Search Results

Search found 14684 results on 588 pages for 'static rtti'.

Page 417/588 | < Previous Page | 413 414 415 416 417 418 419 420 421 422 423 424  | Next Page >

• Troubleshooting Mid 2007 iMac RAM upgrade

  - by MDT

  I am trying to install new RAM in my friends iMac, something I have done several times before. We unplugged the computer before performing the upgrade, used anti static wrist bands, and yes the memory is compatible and inserted correctly. The stock RAM was Hynix 1gb pc2-5300s-555-12 and the memory we are replacing it with is 2x2gb Centon CMP800SO2048.01. Now I know this model number suggests that the ram is 800MHz and the iMac is only 667MHz but it clearly states on the box that this RAM is PC2-5300 667MHz compatible. The problem is, that when I install the new RAM I get little response from the computer. I hear the hard drive and disk drive start to initialize, but then they just stop and the screen remains black. I have tried every variation of the new RAM and the old RAM in both slots and even tried the same RAM from my old iMac and I just can't get it to boot. Has anyone ever had a problem like this? Thank you in advance for any and all input on thus issue!

  Read the article

• Slow upload speeds with pfsense virtual appliance

  - by Justin Shin

  I have a pfSense virtual appliance set up in front of a Windows server. The pfSense appliance has been configured with two L2L IPSec VPN sites and not too much else. The appliance has two vNics which both exist on the same VLAN, but one is "WAN" and the other is "LAN." When I run speedtest.net on my Windows server when I have configured it to use a static WAN address and gateway, I get great speeds - maybe around 50 down, 15 up. However, when I configure it with a private IP address, I get similar download speeds but terrible upload speeds - around 2 or 3 Mbps consistently. I used Wireshark to see what gives but there didn't appear to be too much helpful information there, or I just could not find it. Besides the L2L VPNs, other configurations include: Automatic Outbound NAT Virtual P-ARP IP for the Windows Server WAN Firewall rule to allow * to * on RDP WAN Firewall rule to allow * to * (enabled this just for testing... didn't help!) No DHCP or any other services besides IPSec VPN No Errors LAN or WAN No collisions LAN or WAN I would be happy to post the full config file if it would help. I've been scratching my head at this one all day!

  Read the article

• Cent OS ifcfg configuration for ranges of IP's with different netmask

  - by Aaron Schlegel

  I have 1 set of 30 public IP's with a netmask of 255.255.255.0 and another set of 30 IP's with a netmask of 255.255.255.128. Both sets of IP's also have different gateways. How can I virtually assign the IP's to the machine? I have tried creating ifcfg-eth0:0 ifcfg-eth0:1 ifcfg-eth0:X ect for each IP. Below is my ifcfg file with. I have this for each IP with the correct gateway IP and netmask for each of my 60 IP's. If I do ip addr show it does show all of the 60 addresses with the correct broadcast IP and netmask. However I can only use 30 of my IP's that are from the same netmask. Am I doing this correctly? If the IP's show up with ip addr show does that mean I have correctly assigned them to the machine virtually? I want to check before I blame my hosting company for not routing the IP's correctly. DEVICE="eth0:1" BOOTPROTO="static" DNS1="**.**.**.**" DNS2="**.**.**.**" GATEWAY="2**.**.***.126" HOSTNAME="localhost.localdomain" HWADDR="0*:19:**:**:**:**" IPADDR="2**.*.**.**" IPV6INIT="no" MTU="1500" NETMASK="255.255.255.128" NM_CONTROLLED="yes" ONBOOT="yes" TYPE="Ethernet" Also is there a better way to do this? I have used ifcfg-eth0:0-range1 before to assign a range of IP's from the same netmask. Is it possible to do this with ranges with different netmask? Thanks!

  Read the article

• Nginx all subdomain points to one subdomain (gitlab) rule

  - by Alkimake

  I have installed gitlab on my server and use nginx as http server... I simply used recipe for gitlab on nginx # GITLAB # Maintainer: @randx # App Version: 3.0 upstream gitlab { server unix:/home/gitlab/gitlab/tmp/sockets/gitlab.socket; } server { listen 192.168.250.81:80; # e.g., listen 192.168.1.1:80; server_name gitlab.xxx.com; # e.g., server_name source.example.com; root /home/gitlab/gitlab/public; # individual nginx logs for this gitlab vhost access_log /var/log/nginx/gitlab_access.log; error_log /var/log/nginx/gitlab_error.log; location / { # serve static files from defined root folder;. # @gitlab is a named location for the upstream fallback, see below try_files $uri $uri/index.html $uri.html @gitlab; } # if a file, which is not found in the root folder is requested, # then the proxy pass the request to the upsteam (gitlab unicorn) location @gitlab { proxy_read_timeout 300; # https://github.com/gitlabhq/gitlabhq/issues/694 proxy_connect_timeout 300; # https://github.com/gitlabhq/gitlabhq/issues/694 proxy_redirect off; proxy_set_header X-Forwarded-Proto $scheme; proxy_set_header Host $http_host; proxy_set_header X-Real-IP $remote_addr; proxy_pass http://gitlab; } } gitlab.xxx.com works fine and i get gitlab web documents. But if i want another subdomain i use for Jira (jira.xxx.com) on port 80 (i setup jira on 8080 port normally) gets gitlab web site also. How can i restrict this rule only serving for gitlab, or may be i can redirect jira.xxx.com to jira.xxx.com:8080

  Read the article

• Apache+PHP on Windows Server 2008

  - by Álvaro G. Vicario

  I've installed Apache/2.2 and PHP/5.3 lots of times under Windows XP, Windows Vista and Windows Server 2003. The official *.msi installers work fine and configure everything. Now I need to install them into a Windows Server 2008 R2 Standard 64-bit box and I'm facing nothing but problems: There are no official 64 bit binaries for Apache and no binaries at all for PHP (official or third-party). It's alright, I'll do with good 32 bits, but it's kind of surprising. Official documentation is vague, generic and completely unaware of UAC or any recent Windows security feature. The PHP installer is unable to configure mod_php and the Apache installer is unable to configure... well, Apache. After three hours I've finally reached the point where I'm installing everything in the root folder and assigning full control access to all users in all files and directories and all I've got is a PHP-less Apache server that's able to serve static pages. So I guess it's time to stop and think. My question is: Has anyone installed an Apache+PHP production server under Windows Server 2008 in a serious, secure and reliable way and documented the whole process? Or should I just find a bundle like XAMPP and the like that requires no installation? === EDIT === I've installed Xampp Lite 1.7.3 and everything was working in 5 minutes. I'd still like to find some documentation about installing the original packages: XAMPP installs tons of stuff I don't need and offers no tool to enable and disable PHP extensions.

  Read the article

• Traceroute, * at first router

  - by Jérôme

  When using traceroute on my mac to check the path to any website, the first line is always 3 stars. imac:~ Jerome$ traceroute google.com traceroute: Warning: google.com has multiple addresses; using 173.194.70.113 traceroute to google.com (173.194.70.113), 64 hops max, 52 byte packets 1 * * * 2 217-168-54-101.static.cablecom.ch (217.168.54.101) 9.515 ms 8.757 ms 10.104 ms 3 172.31.208.73 (172.31.208.73) 14.512 ms 14.605 ms 14.264 ms 4 ch-zrh01b-ra1-ae-1.aorta.net (84.116.134.142) 13.587 ms 12.892 ms 13.936 ms 5 74.125.49.101 (74.125.49.101) 13.966 ms 14.850 ms 14.915 ms 6 72.14.232.120 (72.14.232.120) 26.573 ms 72.14.232.88 (72.14.232.88) 20.072 ms 19.758 ms 7 72.14.236.68 (72.14.236.68) 26.913 ms 72.14.236.20 (72.14.236.20) 26.825 ms 72.14.239.62 (72.14.239.62) 25.381 ms 8 209.85.254.118 (209.85.254.118) 22.240 ms 22.365 ms 209.85.254.112 (209.85.254.112) 24.826 ms 9 * * * 10 fa-in-f113.1e100.net (173.194.70.113) 25.715 ms 26.960 ms 25.191 ms As far as I know, * means no answer from the router. How come I have stars at the very first line ?

  Read the article

• When I ping Internet addresses like yahoo or Google, I get 2 reply packets and 2 lost packets.

  - by navi

  I have Airtel broadband and a Tata broadband connection. i have around 50 PCs connecting through an airtel broadband connection. Both are dsl connections with my phone line going into dsl modems and an Ethernet cable going from dsl modem directly into a switch. Currently, only airtel connection is connected with static IP on my private lan and using the airtel ISP DNS servers as DNS IP address and the default gateway is 192.168.1.1 (IP add. of the dsl modem). All PCs are connected in a work group. When in full use, my users complain of certain web pages are not opening. When I ping Internet addresses like Yahoo or Google I get 2 reply packets and 2 lost packets. I suspect that a single broadband connection is not able to sustain 50 simultaneous downloads/browsing. Is there any device which connect to both DSL and make one line so that its give me high speed simultaneous browsing. Help needed urgently. Thank you all to those who reply.

  Read the article

• Convert raw IMAP server data into local folders, then upload partial dataset to new IMAP server?

  - by Manca Weeks

  I am transitioning a company with about 30 IMAP accounts, loaded with data (about 77GB total), to a new email host. The majority of the data will be converted into a local archive and distributed to the company computers as a static reference data set. The server side folders the users absolutely cannot do without being on the server will be uploaded back to the new server. I used Mac OS X Mail (Snow Leopard 10.6.6) to download the content. I notice some messages have the name [xxx].partial.emlx, which leads me to believe they have not been downloaded all the way. I have root access to the mail server data and could download the IMAP server data via FTP. I am not sure what utility to use to convert that data to local Mail.app mailboxes. Furthermore, I would appreciate any input on the best way to upload a portion of the data to the new server (GoDaddy), preserving the original dates of the messages. edit OK - forget the raw server data. I found a script that apparently does pretty good archiving IMAP folders to local mbx files. My main quest now is to batch upload a mailbox hierarchy to the new IMAP server without having to start-stop and deal with similar issues. Anyone know of a utility (hopefully for OS X, but if not, I'll fire up my XP virtual system...) that would be capable of this? Thanks, M

  Read the article

• Make dhcp assign same IP and hostname for different interfaces at one machine

  - by Egeshi

  I have a feeling that question itself looks stupid but it is not. Please let me clarify. I have dynamic DNS with BIND and NIS configured at my LAN and have laptop which I am using in both wireless and wired mode. I mean that sometimes I have to use wired interface to achieve higher throughput but most of time I don't need it and using wireless mode. Everything works great. Issue is that I want both interfaces get same IP from DHCP. Just for convenient firewall setup. If I add both hosts to dhcp in this manner # bt wireless host bt { hardware ethernet 00:1f:1f:62:60:28; fixed-address 172.16.77.110; } # bt wired host bt { hardware ethernet 00:14:22:b7:5a:de; fixed-address 172.16.77.110; } DHCP says logs following message dhcpd: Dynamic and static leases present for 172.16.77.110 dhcpd: Remove host declaration bt-wired or remove 172.16.77.110 dhcpd: from the dynamic address pool for 172.16/16 Host records are added outside of any subnet, but it makes no difference if I put them there, effect is still the same. This is not critical but either is not my whim because even if DHCP seems to work fine for that "bt" host, I cannot make connection TO it from remote machine anymore with this definitely incorrect DHCP config. I'd be thankful if one spares a minute for advice about how to configure DHCPD correctly. UPDATE. I realize that there's a soulution to assign different hostname in DHCP config but would like to use benefits of short host names.

  Read the article

• Unusual Caching Issue with IE 7/8 and IIS 7

  - by Daniel A. White

  We recently moved a site into production running Server 2008 x64 and IIS 7. The ASP.NET pages apparently load just fine, but when it comes to IE 7 and 8, a weird caching issue has cropped up with the CSS and JavaScript files on the page. On a very sporadic schedule, IE does not get all the files necessary to compose the page (i.e. CSS and JS files). When I manually go to the missing files from the address bar, they come back from local cache as empty. I F5 these source files and magically they come down properly. I refresh the site after loading a few files and the cache seems to hold. This problem has only been reproduced (again, sporadically) on IE 7 and 8 running XP. Chrome and Firefox appear to be immune. We have set IIS to use server-side kernel caching for CSS, JS and images. We also have set to expire content for the App_Themes and Scripts directories to expire immediately. One initial thought it was a SWF loading an FLV on page load. These fixes have not remedied the problem. We had no problems on our staging server which is using Server 2003 and IIS 6. Any ideas would be greatly appreciated. P.S. It sounds similar to this problem: but we do have the Static Content module installed. http://serverfault.com/questions/115099/iis-content-length-0-for-css-javascript-and-images

  Read the article

• Setting up a Pagefile and Partition in Server 2008

  - by Brett Powell

  I am setting up 18 new machines for our company, and I have instructions from my new boss on setting up a Pagefile and Partition. I have looked at their existing machines to base the new setups off of, but there is no consistency between any 2 machines, which has left me extremely frustrated to say the least. My instructions are... 1) Set a static pagefile (use recommended value as max/min), set it on SSD if SSD available. 2) Make 3 partitions: C: is used for OS and install files D: is used for backups on machines with a SSD. On machines without SSD create a D: partition for pagefile (2*installed RAM for partition size) E: must be the partition hosting user files I have never messed with Pagefiles before, and looking at their existing machines is offering no help. My questions are... 1) As the machines I am setting up have no SSD (just 2 SATA drives) does it sound like the Pagefile should be setup on the C: (primary) drive or the D:? The instructions are vague so I have no idea. 2) As C: and D: are both Physical drives, does it sound like C: should be partitioned out to create the E: drive or D:? Thanks for any help I can get. I am extremely stressed out under a massive workload right now, and these vague instructions are quite infuriating.

  Read the article

• How can ICS in Windows 7 be managed via command line, scripts, config files, etc.?

  - by Skya

  I've been using ICS successfully for years, but now I'm looking for a way to control it through something else than the GUI in Control Panel\Network and Internet\Network Connections - Connection Properties: I want to do everything that the encircled checkbox does, without touching the GUI. But what does the checkbox do? Microsoft don't provide specific information and the most helpful forum post I've found is from 2003. Assuming that some of the advice is still valid, I've come to the conclusion that ICS is broken down into 6 parts that have to be set up individually: the sharedAccess service interface settings firewall rules a static route dnsproxy autodhcp I've already learned that the service can be started/stopped with the command net start/stop sharedAccess and that netsh is a good tool for changing the interface settings and the firewall rules. But I don't understand how ICS handles routing and DNS. All hosts in my network are configured statically, so I don't care much about autodhcp. Thanks for your help! EDIT: I've spent the whole day scanning through ProcMon and I've seen reads/writes to both the registry and the filesystem and it is difficult to determine what parts of it actually make ICS work. I'm trying to look for an API instead. I'm looking into this right now, but I still want to know more about the inner workings.

  Read the article

• Workstations cannot see new MS Server 2008 domain, but can access DHCP.

  - by Radix

  The XP Pro workstations do not see the new replacement domain upon boot; they only see their cached entry for the old (server 2003) domain controller. The old_server is not connected to the network. I have DHCP working with the same scope as the old_server. In my "before-asking" search for a solution I came across the following two articles, and I recall doing things as suggested by the articles. http://www.windowsreference.com/windows-server-2008/how-to-setup-dhcp-server-in-windows-server-2008-step-by-step-guide/ http://www.windowsreference.com/windows-server-2008/step-by-step-guide-for-windows-server-2008-domain-controller-and-dns-server-setup/ The only possible issue is: I was under the impression that the domain netbios needed to match the DC's netbios. The DC netbios is city01 while the domain's FQDN is city.domain.org (I think this is mistaken and should have been just domain.org) But, the second link led me to a post which I believe answers my question. I did as they instructed by opening Local Area Connection Properties, then selecting TCP/IPv4 and setting the sole preferred DNS server to the local hosts static IP (10.10.1.1). Search for "Your problems should clear up" for the post I'm referencing: http://forums.techarena.in/active-directory/1032797.htm Have I misunderstood their instructions? I am hoping to reach the point where I can define users and user groups. Also, does TechNet have a single theoretical overview document I could read. I really don't like treating comps as magic. I will be watching this closely and will quickly answer any questions. If I've left anything out it is because I did not know it was needed. PS: I am loath to ask obviously basic questions, but I am tired and wish to fix this before tomorrow. Also, this is my first server installation, thank you for your help.

  Read the article

• Cannot establish a network connect to VMWare Fusion VM

  - by twolfe18

  I am running Snow Leopard 10.6.2 (not the server edition) with VMWare Fusion 3.0.0 and I trying to get my Ubuntu 9.10 x86_64 VM working. I am using a bridged connection, and I have an internet connection FROM the Ubuntu VM (I can download updates, ping websites, etc), but I cannot connect TO the Ubuntu box from any other device on my network. I am trying to get Mongrel up on the Ubuntu VM for some Rails stuff, but it's not working. I know Mongrel/Rails is not the problem because if I start the server on the Ubuntu VM, background the process, and then wget the index page, it works. I just cannot connect to the site from another IP. I have tried using a static IP and a DHCP IP configuration on the Ubuntu VM, neither work (for incoming connections, both work for outwards). I have port scanned the Ubuntu VM, and it appears that all ports are closed. However, the Ubuntu VM does respond to pings. I noticed a similar question here: http://serverfault.com/questions/99757/setting-up-a-bridged-network-with-vmware-fusion, but no answer. Any ideas?

  Read the article

• Convert a Linksys WAG54GP2 ADSL router into Access point only to extend my Wifi range

  - by Preet Sangha

  I have a wireless lan running on my ASDL2 connection. The router (Seimens Gigaset sx763) is provided by the ISP and is generally good. However I have couple of dead spots at the far end of the house and since I have my old router sitting in the drawer I thought that I'd try to convert it into simple WAP. However downloading the manual from linksys it seems to be that the manual is from an earlier firmware, but the very first option on the very first page seems promising: Wan Mode: Router or ADSL However after this I'm a bit lost. I know that the wireless card on this box will need a mac address and it must get its address from the master router (I thought static might be best). However the again the manual is out of date I have the option of DHCP: ON or OFF or RELAY I've not even got to the more complex options yet. Question is can this device even work this way (seems like it but I cannot find any docs on it), and if so how? Edit: Having now fiddled around I'm of the opinion that this cannot be done.

  Read the article

• Linksys WAP54G v3.1 no access, power and link LED solid

  - by user142113

  I'm managing the Network of a small enterprise. A Linksys WAP54G v3.1 used to provide the WiFi network. I was called, because the device did not provide a WiFi network anymore. I first of all tried to ping the device via LAN, but there was no reaction. I've frequently reconnected the AP to the mains and always the POWER and the LINK LED keep solid, even if no network cable is connected. What I've done yet: Reset as documented: Pressed the RESET button for 10 seconds. After that I have tried to access the AP with a direct cable connection to my computer, that I've set to a static ip of 192.168.1.240, but i got no ping response on the default IP 192.168.1.245. Furthermore ipconfig reports "media disconnected". More complex reset method as described here http://bruceshankle.blogspot.de/2005/12/how-to-reset-linksys-wap54g.html as well had no effect. also tried to ping 192.168.1.1 without success Tried this method: http://www.daniweb.com/hardware-and-software/networking/threads/142437/linksys-wireless-access-point-problem#post680245 but there was no ping response when powering up. As well the tftp transfer timed out Finally tried to short pin 15 and 16 of the flash chip on the bottom side of the AP mainboard while booting to provoke a Checksum error. This should lead to the possibility to upload a firmware with tftp, as the AP stops booting and waits for a tftp connection on 192.168.1.1. But I've had no success. As well i've put pin 15 and 16 to ground while booting, also without an effect. After all that I still can't ping the AP, ipconfig still tells me "media disconnected". The POWER and LINK LED are solid. I would appreciate your answers

  Read the article

• Routing WIFI and LAN for specific traffic

  - by jakebird451

  I have two network devices aboard my macbook pro: WIFI (en1): Used for general traffic. Connects to an ip of 192.168.19.* via DHCP LAN (en0): Used for specific traffic. Connects to an ip of 192.168.2.10 as a static IP. Does not connect to a router, only a switch for direct routing connection. I have 4 IP addresses I need to access on the LAN: 192.168.2.1 192.168.2.21 192.168.2.20 192.168.2.30 The rest of the traffic needs to go to WIFI. I have tried setting up a routing table for the specific ip addresses, but I only managed to mess up my network. I do not venture out into the world of networking too often, but this was the latest command I have been trying: sudo route add -host 192.168.2.30 -interface en0 This command killed my ability to use ping. It told me that ping could not allocate memory (is that even possible)? It also killed my wifi access. Logging out and back in fixed the issue. I really do not mind to make this solution permanent, so I am fine with a temporary routing. EDIT: If I currently have been trying: sudo route flush sudo route add default 192.168.19.1 This gets everything to work for about a minute. But after such minute it "forgets" the routing to WiFi while retaining LAN's (en0) routing. If I unplug and replug my LAN (en0) cable, the process works for another minute.

  Read the article

• Windows xp mapped drives disconnect from Windows 7 on Peer to Peer network

  - by Kathryn Codo

  I have a 5 user peer to peer network. 2-XP machines, 3- Windows 7 machines and a Windows 7 machine acting as the file server. I have NO issues with the Windows 7 machines staying connected via the mapped drives to the "server". However, once a day the 2 XP machines will not connect to the Windows 7 machine "server" via the mapped drives. I must restart the "server" in order to see the server and access the files via the mapped drives or Explorer. I have tried the persistent : yes command in NET USE, on the XP machines and also setting a static IP address on the "server". I've turned the firewall off on the "server:, no difference so I turned the firewall back on. No interruption occurs with the internet when this happens, just can't see the server. Again, the Windows 7 users are unaffected. I have gone into the advanced network settings on the "server" and added read/write permissions for Everyone as well as the users of the XP machines. I have double checked that we are all on the same WORKGROUP. I'm at a loss. It seems to happen around mid-day and I've not been able to find any activity that is happening at this time (Like someone plugging in a thumbdrive). Any suggestions would be greatly appreciated as my client is running old XP software he no longer has the disks for and needs for his engineering firm.

  Read the article

• Networking 2 Virtual PC with one VPC as DHCP server

  - by vivek

  My host OS is Win XP Professional. The host has a real network connection via DSL and I created a second network connection using Microsoft Loopback Adapter. Internet connection sharing is enabled. The Microsoft Loopback adapter has a IP address of 192.168.0.1. I have 1 Virtual PC which has Windows Server 2003. I have setup the network connection on this VPC to use Microsoft Loopback Adapter. I setup this VPC to be the Domain Controller , DNS Server and DHCP Server. I set this to a static IP address 192.168.0.2 (on the same subnet as the MS Loopback adapter) I have a second Virtual PC which also has Windows Server 2003. The network connection on this VPC is set to "Local Only". I want this VPC to get its IP address from the 1st VPC on which I setup as a DHCP server. What i want is the 2 VPC should be in a network with one of the VPC acting as the domain controller, DNS Server and DHCP server. The second VPC shoud get its IP address from the 1st VPC. It should be a part of the domain of the 1st VPC. When i tried to make the second VPC get the IP address from the first VPC I am not succeeding. Can somebody post some suggestions on how to go about this ?

  Read the article

• PHP extension causes symbol lookup error

  - by Christian

  Dear, I installed - or better tried to - the NMCryptGate Extension for PHP on my Debian 5.0.8 server. I did this by compiling the sources which came up with no error message. Calling phpinfo() I can see the extension as enabled. BUT, whenever I try calling a method from this extension I get an error logged to the apache error log: /usr/sbin/apache2: symbol lookup error: /usr/lib/php5/20060613+lfs/nmcryptgate.so: undefined symbol: nmlistalloc What is missing? I got two packages from the software company: the php module sources and some files which should - according to their path inside the tar - go to /usr/local/bin|doc|include|lib. I moved them there without any effect. Each of these two packages has its own config file almost looking the same: \# libnmcryptgate.la - a libtool library file \# Generated by ltmain.sh - GNU libtool 1.3.4 (1.385.2.196 1999/12/07 21:47:57) \# \# Please DO NOT delete this file \# It is necessary for linking the library \# The name that we can dlopen(3) dlname='' \# Names of this library library_names='libnmcryptgate.so.1 libnmcryptgate.so libnmcryptgate.so' \# The name of the static archive old_library='' \# Libraries that this one depends upon dependency_libs=' -L. -L/usr/ssl/lib -L/usr/local/ssl/lib -L/usr/local/lib -lssl -lcrypto' \# Version information for libnmcryptgate current=1 age=0 revision=29 \# Is this an already installed library installed=yes \# Directory that this library needs to be installed in libdir='/usr/local/lib' I tried several ways to get it right: moving files, symlinking, changing configurations - always followed by restarting apache - no success. I guess I just have to move the files to the correct location or change the libdir inside the config files but meanwhile I'm totally confused by the two packages: do I need both, which config rules what, do I have to use the libdir variable? And for what? ... Anybody out there hinting me to my source of failure? Thank you in advance, regards, Christian

  Read the article

• Windows Server 2003 with Apache and IIS causing random faulting and performance issues with Apache?

  - by contrebis

  I'm trying to fix a problem on a Windows Server 2003 SE install which is running IIS6 and Apache webserver (with PHP and MySQL). IIS sites are bound to one IP, Apache to the other. Everything seemed fine till the other IP address was installed to allow a webservice to run under IIS. Symptoms: Apache now responds very slowly, even requests for static files (often 30 seconds or more) Sporadic errors are appearing in the event logs like: Faulting application httpd.exe, version 2.2.14.0, faulting module php5ts.dll, version 5.2.13.13, fault address 0x000ac14f. I've double-checked the config files, taken account of this question/answer http://serverfault.com/questions/51230/running-iis-and-apache-on-the-same-windows-server, upped the Apache log level to debug, run TCPView to check for conflicting bindings, upgraded to latest Apache/PHP versions but still no success or indication of a cause. Any suggestions on where to look, or debugging tips would be gratefully received. I'm a web programmer so not so familiar with Windows Server admin or details of the networking stack. Running PHP under IIS is not an option and hosting on another server is non-ideal.

  Read the article

• RRAS NAT not working on a certain computer

  - by legenden

  This is driving me crazy. I have a virtualized W2K8 server running RRAS. Every other computer or server on the network can access the internet through the NAT except one. On one server, it just won't work. I can ping the ip address of the NAT gateway just fine, and everything else works. (SMB, etc) DNS, which is hosted by the same server, also works just fine. I have even reinstalled the OS on the problem server and it still doesn't work. Recap of the steps I tried: There are 3 network cards in the server, I tried every one and different switch ports. Not a hardware problem. Reinstalled W2K8 R2 on server with the problem, didn't help. Tried the IP of the internet gateway directly - this did work (!). But I need NAT to work. All firewalls are disabled. Removed computer from domain, deleted computer membership in Active Directory Users and Computers and added it back. Disabled all other network adapters and set a static ip and specified the gateway ip manually. When I tracert a public IP, the first hop (or any other hop) comes up as: C:\>tracert www.google.com Tracing route to www.l.google.com [209.85.225.106] over a maximum of 30 hops: 1 * * * Request timed out. 2 * * * Request timed out. From a different computer, on which NAT works, the first hop comes up as: tracert www.google.com Tracing route to www.l.google.com [209.85.225.105] over a maximum of 30 hops: 1 <1 ms * <1 ms xxxx [10.5.1.1] This is the most bizarre problem I ever came across, and I realize that it's a long shot asking it here given all the details, but I'm pulling my hair out. Maybe someone has an idea...

  Read the article

• Multiple IPv6 addresses being assigned to single interface

  - by Steven Copestake

  I'm configuring a DHCP scope for IPv6, however all my clients are getting 2 or more IPv6 addresses assigned to the interface. I'm using fda8:6c3:ce53:a890:/64 as the prefix. The scope is on a machine running Windows Server 2008 R2 however I'm looking to roll it out on Server 2012 as well. My clients are getting the following: IPv6 Address. . . . . . . . . . . : 1024::1492:9288:7357:7d30(Preferred) IPv6 Address. . . . . . . . . . . : fda8:6c3:ce53:a890::1(Preferred) IPv6 Address. . . . . . . . . . . : fda8:6c3:ce53:a890:1492:9288:7357:7d30(Pr rred) Link-local IPv6 Address . . . . . : fe80::1492:9288:7357:7d30%10(Preferred) In this example there's no DHCP scope and the machine has a static IP of fda8:6c3:ce53:a890::1. With this in mind where are the 1024 address and the fda8:6c3:ce53:a890:1492:9288:7357:7d30 address coming from?

  Read the article

• Apache2 with lighttpd as proxy

  - by andrzejp

  Hi, I am using apache2 as web server. I would like to help him lighttpd as a proxy for static content. Unfortunately I can not well set up lighttpd and apache2. (OS: Debian) Important things from lighttpd.config: server.modules = ( "mod_access", "mod_alias", "mod_accesslog", "mod_proxy", "mod_status", ) server.document-root = "/www/" server.port = 82 server.bind = "localhost" $HTTP["remoteip"] =~ "127.0.0.1" { alias.url += ( "/doc/" => "/usr/share/doc/", "/images/" => "/usr/share/images/" ) $HTTP["url"] =~ "^/doc/|^/images/" { dir-listing.activate = "enable" } } I would like to use lighttpd in only one site operating as a virtual directory on apache2. Configuration of this virtual directory: ProxyRequests Off ProxyPreserveHost On ProxyPass /images http://0.0.0.0:82/ ProxyPass /imagehosting http://0.0.0.0:82/ ProxyPass /pictures http://0.0.0.0:82/ ProxyPassReverse / http://0.0.0.0:82/ ServerName MY_VALUES ServerAlias www.MY_VALUES UseCanonicalName Off DocumentRoot /www/MYAPP/forum <Directory "/www/MYAPP/forum"> DirectoryIndex index.htm index.php AllowOverride None ... As you can see (or not;)) my service is physically located at the path: / www / myapp / forum and I would like to support lighttpd dealt with folders: / www / myapp / forum / images / www / myapp / forum / imagehosting / www / myapp / forum / pictures and left the rest (PHP scripts) for apache After running lighttpd and apache2 working party, but did not show up any images of these locations. What is wrong?

  Read the article

• Internet connection & IIS stopped on windows xp after VMware server 2 installation

  - by Eduardo Xavier

  Hi, I'm running a local network. My IP ranges from 192.168.1.2 to 192.168.1.15. All IP are static ones. And my router's IP is 192.168.1.1 and I provide it as default gateway and preferred DNS server on client machines. Everything worked fine on this scenario. I could use internet and reach services on other machines. BUT I have installed VMware server 2 on the windows XP to host windows 2003 Virtual Machine (VM). I set the following configuration: Windows XP's => 192.168.1.11. Windows 2003 => 192.168.1.12. (virtual machine) This approach worked just fine as it used to work with Microsoft Virtual PC. I can access mysql & IIS websites on the windows 2003 virtual machine. BUT two things doesn't work anymore on the Windows XP: internet connection - but I can see the MAC address on the wireless router IIS - Ping on 127.0.0.1 it's ok as I can hit localhost:8222 nor localhost Does anyone knows how to fix any of this? (at least the internet connection)

  Read the article

< Previous Page | 413 414 415 416 417 418 419 420 421 422 423 424  | Next Page >