Search Results

Search found 19446 results on 778 pages for 'network printer'.

Page 418/778 | < Previous Page | 414 415 416 417 418 419 420 421 422 423 424 425  | Next Page >

• LMDE detects a wireless card, but can't use it

  - by Davidos

  LMDE can see my wireless card, and correctly identifies it, but it refuses to let me turn it on through the shiny graphical interface. Is there a way to use the non-shiny terminal to turn on my wireless? One small tidbit I noticed was the stated version; it says the version is 00. I believe that's hexadecimal for 0, which may indicate something screwy with the software. It would be nice if someone could tell me how to figure out how to solve this kind of problem in the future. *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 00 serial: 91:e3:7b:0d:a3:a9 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-1-amd64 firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:43 memory:e1d00000-e1d01fff I've tested multiple other network managers, and none of them work. W ireless switch is on, I'm sure it's a driver problem.

  Read the article

• Different subnets routing with just one layer 3 switch

  - by GustavoFSx

  Our current network looks like this: Location 1: 2 Layer 2 switches | subnet 192.168.1.0/24 | Firewall for our VPN Location 2: 1 Layer 2 switch | subnet 192.168.3.0/24 | Firewall for our VPN Location 3: 1 Layer 2 switch | subnet 192.168.5.0/24 | Firewall for our VPN We just got a direct fiber connection between location 1 and 2, we also got a new HP V1910 24G layer 3 switch. I tried to follow the instructions on this site, but I can't get it to work. I think our network should look like this: Location 1: HP Switch FIBER to L2 | subnet 192.168.1.0/24 | Firewall for our VPN Location 2: 1 Layer 2 switch | subnet 192.168.3.0/24 | FIBER to L1 Location 3: 1 Layer 2 switch | subnet 192.168.5.0/24 | Firewall for our VPN So, how can I get routing working on our location 2? It's old gateway was a firewall device on ip 192.168.3.1. I'm thinking on creating a VLAN Interface on 192.168.3.1 on the switch for the Location 2. But how will I handle that on the HP switch that has a direct fiber connection with that switch? Please help, I'm not very good with networking.

  Read the article

• How to use non-free drivers during debian install

  - by blokeley

  I'm trying to install debian stable using unetbootin. The install process fails with "network autoconfiguration failed", probably due to the ethernet driver not working. My Lenovo U350 has a Broadcom BCM57780 which does not seem to be supported out-of-the-box: there are various bug reports here, here and here, but I don't know if the fix has made it into debian (6) stable. One discussion says that you have to use an ethernet driver from the firmware-linux-nonfree package. I'm not sure that this is correct because the BCM57780 is not in the list of drivers in firmware-linux-nonfree. The specific question tree is: Is BCM57780 supported in debian stable? If so, what could be wrong? Should I install debian unstable instead? If not, do I need to use firmware-linux-nonfree during installation and, if so, how do I do this? Please note: I've used ubuntu and debian loads in the past but please post line-by-line guidance rather than some cryptic abbreviation of any instructions. Thanks in advance for any help. Updates: Debian stable with non-free drivers did not work. Debian unstable (free drivers only) did not work. Tried loading firmware-iwlwifi_0.28_all.deb from another USB stick to get wireless working rather than BCM57780. The .deb file was found but the network configuration still failed! That's it, I'm giving up. Unfortunately I'll use ubuntu even though the Unity user interface will be very unstable for the next couple of years :(

  Read the article

• Migrate active directory to Google apps for business

  - by dewnix

  I've got a problem migrating active directory to Gapps. I'm stuck on google apps directory sync (GADS) where it just gives the error "java.lang.NullPointerException" after testing the connection during the LDAP configuration step. I checked the logs and I've pretty much determined that port 389 (standard LDAP port) isn't listening on the exchange server. I've tried telneting to it (from another machine in the same network) with no luck but I can telnet to other ports, that i know are open, successfully. I know they're open because I used portqry and netstat to see them. I'm suspecting that the active directory isn't even installed/running on this machine because there's no active directory services at all running on it. There's no active directory services that say they're NOT running either though. Is it possible AD is installed somewhere else? does it have to be on a machine inside the same network? I found the domain controller and it's host name and when I telnet with port 389, it works however GADS still gives me the same exact error when I substitute that server in. Actually, no matter what ridiculous settings i put into GADS, i still get that same NullPointer error. If i could get some different error than that NullPointer, i'd call that a successful day.

  Read the article

• Sizing Switches for Storage and Production

  - by Untalented

  Couple questions. Should you always completely separate the storage network switches from production switches or are VLANs fine to segment this traffic? Is there a golden rule here? How do you properly size a switch for your environment based on the specifications the manufacturer provide (Throughput, Forwarding Throughput, Stacking Throughput, Max Mac)? If you have two switch options and one has a maximum Mac address of 8,000 vs. another with 16,0000. What does this really mean to me? How do make sure one vs. another is sized properly for me? Besides VLAN and Jumbo Frame support, is there any other "Must" haves for a virtual environments production or storage networks? There is a wealth of knowledge on sizing SANs and such, but this seems equally important and it's quite challenging to find as much information. -- Just to add some tidbits of information for the environment. This setup above is referring to the data centers which supports two different locations which have about 100 users between the two in total. The storage traffic will be iSCSI and will be 3 ESXi Hosts and one SAN housing about 2.7TB of data. Since there is currently no storage network in place (no SAN), I'm having a hard time regarding #2 to really determine what backplane throughput and switch specifications will be sufficient.

  Read the article

• Can only ssh when not using wifi

  - by AChrapko

  So I have 3 machines, a windows 7 desktop that is always wired to my router, osX laptop, and raspberry pi running debian linux. My router is a Linksys e1000 wireless N. My goal is to be able to ssh the raspi from any machine, while it is connected via wifi. My problem is that when trying to ssh from either the win7 or osX to the Pi it either times out, or gives an error: "ssh: connect to host 192.168.1.### port 22: No route to host" The only times that I have managed to connect to the pi from any machine were when it connected to the router via an Ethernet cable. Currently with win7 desktop wired, macbook wireless, and pi wireless tests give the following: win7 ping macbook: Destination host unreachable. macbook ping win7: Request timeout. win7 ping pi: Destination host unreachable. macbook ping pi: Request timeout. blah blah blah Plugging the macbook into the router with an Ethernet cable all communication between win7 and macbook works. Pings, ssh, ftp, smb ect... No changes to the pi, still no connections possible to or from any of the other 2 machines. Note All machines, are able to connect to the internet and ssh to the same machine on a completely different network, wired or over wifi. Plugging the Pi in with Ethernet (and macbook still wired) I can ssh to the pi from both win7 and macbook. I can ssh from the pi to macbook. All machines still able to connect the the off network machine. Also another little side note- I was playing warcraft 3 with my roommates the other day, and the only time they were able to see my LAN game was when they were plugged into the router with an Ethernet cable. Once or twice one of the laptops was able to connect over wifi, but not without another computer connecting first via Ethernet. So basically does anyone have any info as to why my router seems to completely ignore local wireless traffic?

  Read the article

• Removing Phantom Registry Entries

  - by shedd

  First, some background: I'm trying to install an HP OfficeJet 6500. I've got the printer setup on my network fine, but the driver software installation on Windows XP (SP3) is a PITA. The installation program keeps dying with the following error: Product: Network -- Error 1324. The folder path 'WD Sync Data' contains an invalid character. WD Sync Data is a program on external Western Digital harddrives, which I used to use on this computer, but no external drive is current mounted. I've searched my registry for those keywords, but haven't found anything. I also ran CCleaner on the registry just to make sure, but no loose ends detected there, either. There are a number of Google results for the error, but no solutions. One post pointed me to the Windows Installer Cleanup Utility, but this utility doesn't even run - it dies with the same error before even starting. Any thoughts on where I could look to clean up this invalid character so I can get the HP installation wizard to successfully run? Many thanks in advance!

  Read the article

• BIND9 Forwarding by view

  - by Triztian

  Hi I think this is a simple issue, I'd like to forward only to certain IPs in the LAN network, for example I have 2 acl lists: acl "office1" { 192.168.1.15; // With internet access }; acl "production" { 192.168.1.101; // No internet access }; I know that there probably should be more efficient ways to restrict internet access, but at the moment this is what I'd like to try.Here's what I've tried in named.conf.local // Inlcude my acl definitions include "/etc/bind/acls.conf"; view "no-internet" { match-clients { production; }; include "/etc/bind/named.conf.default-zones"; zone "localdomain.com" { type master; file "/etc/bind/db.localdomain.com"; }; zone "1.168.192.in-addr.arpa" { type master; file "/etc/bind/db.192.168.1"; }; } view "internet" { match-clients { office1; }; include "/etc/bind/named.conf.default-zones"; forwarders { 201.56.59.14; // Made Up 201.56.59.15; // Made Up }; zone "localdomain.com" { type master; file "/etc/bind/db.localdomain.com"; }; zone "1.168.192.in-addr.arpa" { type master; file "/etc/bind/db.192.168.1"; }; }; As you can see I want a localdomain.com defined for every computer in my network and forward internet access to the computers in the office but not to the ones on the production floor. I've modified my conf file, however the IP in the "no-internet" acl is able to resolve the domains, even though I've rebooted the computer, flushed the DNS using ipconfig /flushdns and set my DNS Server as the only one, why is this still happening? Thanks in advance.

  Read the article

• Windows Update broke Wirless driver - Can't get it working again

  - by private_meta

  I naively installed a driver update incoming from Windows Updates yesterday. That caused my Wifi on my Notebook (HP ELitebook 2740p) to break. The network is working as I tried it with my other mobile devices. When installing said driver, it told me that the installation failed. I tried to do a system restore, which did not help getting wifi connectivity back. The device said it was working, but did not get any wifi connection and did not discover any networks. What I tried next was to uninstall the device from my Device Manager and install either the current drivers found through windows, then I tried the same with the current drivers on the HP driver page. both of those attempts failed. It always tells me that installation failed when I uninstall and reinstall drivers. If I try to update the broken driver via internet, it tells me it is up to date, and in the device manager it still views as broken. Next, I 'played' around a bit and reinstalled drivers, and I managed to install drivers from 2012, and when trying to update drivers manually and picking drivers that match the device, it lets me choose between drivers from 2010 and 2014. 2014 would be the current one, picking the 2010 driver leads to the driver being accepted. However, no wireless network can be found. I'm pretty much out of ideas by now, short of reinstalling. The only option I can still think of was that the device broke at the exact moment I installed the new windows driver, but I find that a bit unlikely. Any help would be appreciated fixing this issue.

  Read the article

• Directory service unavailiable, new hardware same settings

  - by Alex

  I'm working on a project with 2 sites connected by a VPN. Site 1 has the main server and there is a secondary server at site 2 which I am trying to replace. The current setup works perfectly however I can't for the life of me get the replacement server at site 2 up and running. I'm trying to replace like for like just upgraded hardware. I have installed the OS (all Server 2003 Standard SP2) and used exactly the same settings as the old server. I have setup Active Directory, DNS Server, DHCP Server and WINS Server configured. I have used all the same settings as the old server (except IP address and name). I can access the active directory but I can't do anything; add, edit, delete all returns "the directory service is unavaliable". No-one can login on any of the computers on site 2 and the internet is down. Plugging the old server back in and connecting it to the network rectifies the issue (so both new and old are connected at site 2), everyone can login and the internet is back (curious since the modem connects direct to the switch, and even with the new server online I can connect to the router via IP but not the net). I really don't have much experience but I've been roped into doing this because my company is too cheap to hire a real network admin. Any suggestions of where I can start to troubleshoot this, its driving me crazy and I only have a day before all the users are back on site.

  Read the article

• My server cant resolve domains?

  - by Nuker

  I am on a VPS that is pretty much unmanaged so it means im on my own. I did my best to configure it so i can host my own site for other people to see it online but seems like i have network problems because in the last days many of my users report they cant enter my site from my domain and seems like Google and Facebook cant either (this never happened before). Its weird because i can enter my site without problems and so many other people as well. But then i tried to make a php include and i get this error: Warning: include(): php_network_getaddresses: getaddrinfo failed: Name or service not known in I was told that seems like my server cant resolve domains. The includes work if i use IPs instead of domains. So it means i have a DNS problem or something? What can i do to fix it? Im on a Linux 2.6.32-431.11.2.el6.x86_64 on x86_64 CentOS Linux 6.5 Thank you. EDIT: i have this on my resolv.conf # Generated by NetworkManager # No nameservers found; try putting DNS servers into your # ifcfg files in /etc/sysconfig/network-scripts like so: # # DNS1=xxx.xxx.xxx.xxx # DNS2=xxx.xxx.xxx.xxx # DOMAIN=lab.foo.com bar.foo.com nameserver 8.8.8.8 nameserver 8.8.4.4

  Read the article

• Different behaviour when running exe from command prompt than in windows

  - by valoukh

  Forgive me if I'm not using the correct terminology here but I'll try to explain the issue I'm having as best I can! We use a program that allows you to view video footage from several cameras, and it works in such a way that when it is opened it then automatically loads several video files within its interface. These video files are stored in a subfolder, e.g. "videos\video1.asf", etc. I didn't create the program so I can't say what method it uses to open the files. The files are stored on a network server and are being accessed via a share/UNC path. When the file is run from windows explorer (by navigating to the network share and double-clicking the exe), it works perfectly. When the file is run via the (elevated) command prompt (e.g. by typing the \server\path\to\file.exe) it opens, but the corresponding video files do not load. I am trying to create a script that launches the program via the command prompt, so the first step is finding out why the two actions above have different consequences. Any advice on how running executables from the command prompt could produce a different result would be greatly appreciated. Thanks

  Read the article

• Local traffic through VPN, global traffic through WAN

  - by ikonoma

  I have an issue with my internet connection. I am using VPN (Aventail Client) to access the local resources. When connected to VPN the Internet traffic passes through it, not through my LAN or Wi-Fi network. I would like to change the routing table to use the Wi-Fi adapter of the PC for WAN traffic. I have routing file, which works very well and routes the traffic in this way, but only when I am physically connected to the local network through LAN. But I can't set it to work with the VPN connection, because I have no gateway when I am connected to it. Etc this in bold is missing. What to do? route change 0.0.0.0 mask 0.0.0.0 172.16.76.1 metric 200 if 12 route change 0.0.0.0 mask 0.0.0.0 10.44.2.1 metric 400 if 11 route add 150.251.0.0 mask 255.255.0.0 10.44.2.1 metric 100 if 11 route add 10.0.0.0 mask 255.0.0.0 10.44.2.1 metric 100 if 11 pause

  Read the article

• Asterisk relay between multiple subnets

  - by immoune

  I wonder what's the best way to go when you have phones on multiple networks which are not directly reachable. I have 3 networks 10.3.x.x 10.6.x.x 10.17.x.x My asterisk server resides on the 10.3.0.5 IP. The machines from the 10.6 and 10.17 networks are routed here through VPN tunnels. At this point we don't talk about NAT anywhere on the network just pure routing. Since the 10.3.0.5 PBX has routes back to all the subnet's it has no problem to communicate with softphones/hardphones from these ranges. The problem comes from that Asterisk (as far as I understand) only responsible for the SIP communication part not the Audio/Video transmission which is in P2P fashion done between the devices. So although a client using sipdroid from 10.6.x.x is able to connect to the pbx (10.3.0.5) and dial a bria client on the 10.17.x.x network once the phone rings out and the call establishes no audio will be transmitted simply because it has no way to directly connect there. For this there are multiple solutions described in this text: http://msdn.microsoft.com/en-us/library/ee480411%28v=winembedded.60%29.aspx What I would prefer is to keep these networks segregated as they are now. What would be the best solution? Is it possible to actually relay through all the audio/video information through the Asterisk server? That would be the best in my case, I using Astlinux there which has a lot of other parts. Thanks

  Read the article

• Routing Traffic With OpenVPN

  - by user224277

  Few minutes ago i configured my VPN server, and actually I can connect to my VPN but all trafic is going through my normal home network. On my OpenVPN application I've got an information : Server IP: **.185.***.*10 Client IP: 10.8.0.6 Traffic: 7.3 KB in, 5.6 KB out Connected: 10 June 2014 19:21:59 So everything is connected but how I can setup on windows 7 that all trafic have to go through OpenVPN network card ?? Client setting : client dev tun proto udp # enter the server's hostname # or IP address here, and port number remote **.185.***.*10 1194 resolv-retry infinite nobind persist-key persist-tun # Use the full filepaths to your # certificates and keys ca ca.crt cert user1.crt key user1.key ns-cert-type server comp-lzo verb 6 Server setting : port 1194 proto udp dev tun # the full paths to your server keys and certs ca /etc/openvpn/keys/ca.crt cert /etc/openvpn/keys/server.crt key /etc/openvpn/keys/server.key dh /etc/openvpn/keys/dh2048.pem cipher BF-CBC # Set server mode, and define a virtual pool of IP # addresses for clients to use. Use any subnet # that does not collide with your existing subnets. # In this example, the server can be pinged at 10.8.0.1 server 10.8.0.0 255.255.255.0 # Set up route(s) to subnet(s) behind # OpenVPN server push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" ifconfig-pool-persist /etc/openvpn/ipp.txt keepalive 10 120 status openvpn-status.log verb 6 and sysctl : net.ipv4.ip_forward=1 Thank you for your time and help.

  Read the article

• Trying to migrate old server to new. Getting duplicate name errors

  - by SpaceCowboy74

  I have an existing server on my network that is running under windows 2000 with SQL Server 2000 on it. We are in the process of moving the server to a windows 2008 platform, with SQL 2008 as well. A few changes are happening though. For one, applications that were on the old server, will now be on a new application server. The issue is, the developers of the original applications hard coded the server name in the apps and/or batch files. I could change all the code, but that would require weeks of work. My original idea was to change the hosts and lmhosts files to point to the new servers with a different IP. So i implemented the following where oldserver was the original server and server is the new one brought online: hosts: 192.168.1.10 oldserver 192.168.1.15 server lmhosts: 192.168.1.10 oldserver #pre 192.168.1.15 server #pre Problem is, when i try to do this, i get the following errors: \\server\c$ Logon Failure : The target account name is incorrect. and \\oldserver\c$ A duplicate name exists on the network. I know about renaming servers in AD, but can't do so yet as the original server is in production and i cannot rename it without breaking a lot of things at the moment. I'm wanting to do a proof of concept to the management before renaming the servers. Any idea how i should resolve this?

  Read the article

• Why won't sql server express 2008 service restart after I enable TCP/IP Protocol?

  - by John

  Whenever I enable TCP/IP connections on my SQL Server Express 2008 database server running on Windows XP SP3, I cannot restart the service, it simply states "The request failed or did respond in a timely fashion". Any suggestions of what I may have configured incorrectly? [update] Here is the applicable part of the Error Log: MSSQL$SQLEXPRESS Server failed to list on 'any' 3060. Error: 0x2747. To proceed, notify you system administrator. MSSQL$SQLEXPRESS TDSSNIClient initialization failed with error 0x2747, status code 0xa. Reason: Unable to initialize the TCP/IP listener. An operation on a socket could not be performed because the system lacked sufficient buffer space or because a queue was full. MSSQL$SQLEXPRESS TDSSNIClient initialization failed with error 0x2747, status code 0x1. Reason: Initialization failed with an infrastructure error. Check for previous errors. An operation on a socket could not be performed because the system lacked sufficient buffer space or because a queue was full. MSSQL$SQLEXPRESS Could not start the network library because of an internal error in the network library. To determine the cause, review the errors immediately preceding this one in the error log. MSSQL$SQLEXPRESS SQL Server could not spawn FRunCM thread. Check the SQL Server error log and the Windows event logs for information about possible related problems.

  Read the article

• Windows-7 Ultimate 64 bit wont connect to my wired/wireless networks

  - by A302

  Windows 7 Ultimate 64 bit. Everything was working fine & then just stopped working. The nic card Realtek PCIe GBE Family Controller is enabled but does not connect to my router (cables & router ports are good). Wireless Atheros AR5007EG is enabled but the connection is limited (encryption type / key have been verified). A laptop running XP can connect both wired / wireless. SSID is not being broadcast, connect to network if it is not broadcasting is checked. Have checked services.msc for Bonjour & did not see it listed. Network & sharing center does not list any active networks. Device manager lists both devices as functioning properly. Router configuration has not been changed. Virus scan has not found anything. I would like to fix this rather than using Acronis to do a system restore. Thanks in advance for any advice offered in solving this. 26 Jan, the nic card & wireless are working using PCLinux OS Live CD. It appears that the problem is Windows 7 related.

  Read the article

• PPTP VPN on Server 2008 Enterprise

  - by Mike K

  I asked this question on Server fault and was told that was not allowed so im moving it here. I am running Windows Server 2008 enterprise in my HOME network inside of vmware workstation. I am running this on my home network to setup a PPTP VPN connection at home. I have correctly setup everything I needed to make it work, including opening all the ports, 1723 and 43 (GRE). I am able to connect just fine, but when I connect I dont have internet unless I uncheck use remote gateway. The thing is, I want to use the remote gateway to route all my traffic through that connection. Can someone tell me why this isnt working and how to get it to work. When I have remote gateway checked, and I do an ipconfig I dont get a remote gateway for the VPN connection, its 0.0.0.0 when id assume if connected properly should be 192.168.1.254 (my ATT Home Router). Also, if I cant get the remote gateway issue to work, and I have to uncheck that box to get internet, does this mean my VPN session is no longer encrypted? I am fully aware the PPTP VPN is the weakest VPN encryption out there but still having that extra layer of security when im on an unsecure wifi connection makes me feel a bit better. Thank you for all your help in advance. Someone told me I need to setup a gateway or router configured on the server. If thats the case, how go I go about telling the remote co

  Read the article

• How to set up vpn tunnel (ipsec) connection

  - by Alfwed

  I'm working with a client who wants to set up a vpn tunnel between their network and ours. They're in charge of the tunnel and to give us the access they are asking me my public IP and my LAN IP. This is what i've got when i do an ifconfig on the server i will use to connect to the vpn $ ifconfig eth0 Link encap:Ethernet HWaddr d4:ae:52:cd:xx:xx inet adr:62.210.xxx.xxx Bcast:62.210.xxx.xxx Masque:255.255.255.0 adr inet6: fe80::d6ae:52ff:xxxx:xx/64 Scope:Lien UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Packets reçus:55255032 erreurs:0 :779628 overruns:0 frame:0 TX packets:5419527 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:1000 Octets reçus:5598164393 (5.5 GB) Octets transmis:1034297288 (1.0 GB) Interruption:16 Mémoire:c0000000-c0012800 lo Link encap:Boucle locale inet adr:127.0.0.1 Masque:255.0.0.0 adr inet6: ::1/128 Scope:Hôte UP LOOPBACK RUNNING MTU:16436 Metric:1 Packets reçus:45923382 erreurs:0 :0 overruns:0 frame:0 TX packets:45923382 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:0 The inet adr:62.210.xxx.xxx is my public IP but it seems like i dont have any LAN IP. Can the connection work without LAN IP or should I create a private network somehow?

  Read the article

• How can I find which logon script is being run?

  - by user2517266

  I'm having an issue with network drives. Suddenly some computers and users aren't getting their mapped network drives from the logon script. I am NOT a domain admin, I don't have permission to login to the domain controller. And I know very little about Active Directory. The issue seems random, some users this day, different users tomorrow. Some computers run fine and some won't map no matter who logs in. They are mixed OS's XP (SP3), Vista, and 7. I was looking at the domain in windows explorer and I have found the batch file(s) that maps the drives in several locations, how do I know which one is actually being ran? The .bat file is located in \DOMAIN\NETLOGON\script.bat and \DOMAIN\SYSVOL\DOMAIN\scripts\script.bat and \DOMAIN\SYSVOL\DOMAIN\policies\GUID(Right? It's a crazy string)\User\Scripts\Logon\script.bat So, how can I figure out which one is actually being ran per computer or user? Cause they are all slightly different from each other and one of them doesn't map properly. Do all the files in NETLOGON get ran? Cause there are 15+ files in there. Or is it specified in Group Policy which one(s) get ran? EDIT: I am able to access a program called Active Directory Users and Computers, but the properties tab for any user is blank for the logon script.

  Read the article

• Y560 Lenovo IdeaPad bandwidth issue

  - by Vlakarados

  I have a Y560 Lenovo IdeaPad, my config: i7 740QM, 4GB RAM, RADEON HD 6570m/5700 1024MB and my network adapter is Intel WIFI Link 5150. The laptop is 2 years old and the problem I'm about to describe is present from the first day. As may be seen here, the receive bandwidth should be up to 300 Mbps, but the maximum download speed from LAN and using torrents is about 2.4MB/s. My internet connection is 100Mbps and other laptops in my house have the appropriate download speed - up to 12MB/s, I have tested at my friends house and at my job, the speed remains the same. I have tried all possible configurations I could think of in network settings - nothing helps. I use Windows 7 and I have had installed different versions (Ultimate, Professional, Home, OEM Home, 64 and 32 bit versions). Some time ago I searched for the problem and found one or two threads that had the same problem and there were something said about a limitation in firmware that some experienced users have managed to bypass. Updating drivers didn't help me either. Is there any reliable way to fix this?

  Read the article

• how to throttle http requests on a linux machine?

  - by hooraygradschool

  EDIT: here is the summery: i need to reduce max connections preferably system wide on Ubuntu 11.04 but at least within Google Chrome. i do not need or want to throttle bandwidth, Verizon seems to only care about the number of connections so that is all i want to change. also, i don't want to use firefox unless i have to, i have three other machines all using chrome and synced and i just prefer it over firefox. i use tethering for my home internet connection via my verizon cell phone. without paying for it. this works just fine for streaming netflix via my nintendo wii and pretty much every other conceivable use ive had for it. except, during heavy usage with multiple tabs open on my laptop, the network connection on my phone will just turn off, then on again, then off, but it never fully connects. i think, based on this and other questions that this is caused by verizon getting too many http requests from my phone. is there some software, script, setting or otherwise that would allow me to throttle my requests to say, 5 or 10 or whatever it turns out is 1 less than verizon is looking for, so that my cell's network connection is not lost? i would far prefer a slow down rather than complete shut off of my internet connection. i am almost certain is from quantity of requests and not related to data, because, as i mentioned, netflix will run all day without a hitch, and that uses more data than anything else i would be doing. if i had a router i am pretty sure there are settings i could easily change to only allow so many requests at a time ... but in this case, my phone is my router, so no settings. im using ubuntu 11.04 on my netbook with an htc incredible on verizon (not that the phone details are relevant) i have been trying to figure this out for quite some time, currently the only fix is ensure that all requests are stopped and then sometimes it works again, other times i have to manually turn my 3g service off and then back on. thank you so much for any assistance!

  Read the article

• Can't connect to FTP server from a specific location

  - by wv_pip

  Last week while uploading website files to our server via FTP, the transfer failed. Ever since then, I haven't been able to connect to the server from work. I can connect just fine from home, or by using an FTP app on my cell phone as long as I'm on the cell network. I can't access the server from any machine on my work network. It's not a credential issue, either. The error message that I always get says that a connection cannot be established, and I am never prompted for my credentials. I have changed absolutely nothing on our domain controller or our firewall/router. I've contacted our ISP (who hosts the website/FTP server) and they can't find anything wrong on their end. They insist that it must be something here at the office that is blocking access. I've also tested access to other FTP servers (ea.com, nvidia.com, etc.) so I know that port 21 is not being blocked. I'm totally stumped. Any help is much appreciated. EDIT: wireshark info here: http://www.cloudshark.org/captures/85a118ae9296?filter=ip.dst%3D%3D66.118.64.208

  Read the article

• Setting up a server that routes local traffic through vpn, while still being able to access internet directly

  - by Kazuo

  The goal is to setup a local server that routes local traffic through an uncontrolled remote vpn service while still being able to access the internet directly (not tunneled via vpn) and provide services through that direct connection. It is supposed to look like this: http://i.stack.imgur.com/74dGC.png Note: There is another router with modem between the local server and the internet. What is the easiest (best?) way to get this network setup working? I'm planning to setup the connection between the local router and the local server with simple ip forwarding. The problem now is that all the server's traffic is routed through the vpn tunnel as soon as I connect the server's openvpn client to the remote service so there is no direct internet connection available. My first idea was to setup a virtual machine (lxc container or something) and run the vpn client and local networking stuff in the vm. So that the vm receives all the incoming traffic from the local router and tunnels it through the vpn. This, as far as I understand, should not affect the physical server's network connection and should allow it to provide services to the internet. Before I start trying to set this up (I don't have much experience in networking), is there any easier or better way to do this? I would be thankful for every suggestion. Edit: Let's say the interface connected to the internet is eth0 and the interface connected to the local router is eth1. Another idea would be to create a virtual interface eth0:0 and specifiy it as openvpn's local endpoint and then force any traffic coming from eth1 through eth0:0. I'm not sure how I would force the traffic through eth0:0, though (possibly by adding routes).

  Read the article

< Previous Page | 414 415 416 417 418 419 420 421 422 423 424 425  | Next Page >