Search Results

Search found 5389 results on 216 pages for 'bridge router'.

Page 42/216 | < Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >

  • ddwrt client brigde acces point lost

    - by llazzaro
    Ok I have an AP with ddwrt firm (i know its not the best, but continue reading!) AP is configured to work like a wifi "transparent" brigde, also it had a virtual wifi network card to expand radius of wifi signal in that same AP. The brigde is working, computers behind AP gets ips from main routers which shares internet....BUT! I cant access webgui of the bridge AP... Main problem : AP is lost, but its working as brigde. I cant find it in the network (it didnt have any ip!) so I cant change any configuration... First solution : Reset AP, but it cannot be done. Reset button dont works due to a bug in ddwrt micro firm that mi linksys WAP54g had installed (I really hate this firmware I like more openwrt that my main router has) Second Solution : arp -a from main router , from computers behind AP...It dont appears in the list. Any more ideas, the router at some level must be there, the brigde is working. I know its possible that the AP is with an ip like 192.168.100.2 , my subnect actually is 172.16.X.X. :) thanks!

    Read the article

  • Wireless Access Point stopped working

    - by Alex Pritchard
    I have a simple LAN set up at home using a Linksys WRT54GSV4 as my primary router and an Encore ENHWI-2AN3 as an access point. I connect the Encore to the Linksys by running a cable from one of the Linksys LAN ports into the Encore WAN input. I originally configured this using the Encore setup wizard, setting the device up in AP Router Mode. It detected the input network and worked about as expected, creating a second network that used my primary network to connect to the internet. It worked fine for about 2 weeks, then abruptly cut out today. I checked to make sure the network was still live through the cable going into the Encore (provides internet when connected to a laptop directly) and that devices are still able to connect to the network being broadcast by the Encore. When I try to rerun the connection wizard on the Encore, I receive the message "No Services found in WAN port." The WAN Settings is no longer retrieving a dynamic ip from the line. I tried providing a static IP, assigning an IP address within the subnet range of my primary router that wasn't being used and pointing the Default Gateway to the Linksys IP, but this did not work either. When I plug the cable into the WAN port, an internet light comes on that is not lit when a live network is not connected. I've tried doing a hard reset on the Encore (held down the rest button until the lights flashed, reconfigured from scratch), but the WAN settings are still not detected. Also tried powering off and on the modem, linksys, and encore. Any suggestions would be appreciated!

    Read the article

  • Cisco configuration for public library internet

    - by AlternateZ
    I'm a C/C++ computer programmer turned IT support guy working for a public library. My day is usually spent helping random grandparents learn how to use email, so my networking knowledge is limited to what I can glean from google. Here's the situation. We have a public library with 20 PCs on a LAN and also public wifi access. Previously we were running all of this on 1 ADSL connection and people complained about low speeds. We hired a networking company to set up a Cisco dual-WAN router for us, and purchased an additional ADSL connection. The intention was to give the LAN PCs a guaranteed amount of bandwidth each, and then let the wifi users split the rest. The results were far worse than what we expected, and all we got from the company was excuses and they've since washed their hands of us. During busy periods, net performance on the LAN PCs are so poor that attaching files to gmail etc often times out and fails - far from the "guaranteed amount of bandwidth each" that we hope for! Sometimes it feels like performance is worse than before when we had 1 ADSL link and an unconfigured router? Anyways, surely this is a problem encountered a million times over across the world? (Sharing internet across many users effectively.) What are standard solutions for something like this? I admit to not even knowing the right jargon to google for (load balancing?) I'd appreciate any links to resources/guides that might help me get a better understanding of the problem/solutions, and perhaps some stories of your own experience in solving similar problems. This will help us evaluate and negotiate with network consultants in the future. If its relevant, our router config contains a section "policy-map" with "bandwidth percent" for each class of user (LAN, wifi), and "fair queue".

    Read the article

  • Configuring two nearby WLANs: should I use the same ssid?

    - by Rory
    I'm configuring a home network for basic internet use (ie don't really need connectivity between workstations on the network). My brick walls mean a single wireless router doesn't provide good coverage throughout the house, so I have purchased two powerline adapters and now have the incoming modem/wireless router at one end of the house plugged into a powerline adapter, and at the other end of the house the other powerline adapter plugged into another wireless router. Currently the two wireless networks have different ssids. (The powerline adapters only do power-Ethernet; they're not wireless access points themselves.) This works well, except when I move between rooms and would ideally like my devices (iPad, phones, laptops) to switch from the weak to the strong signal. Sometimes there's enough signal that they hold on to the weak connects instead of switching to the strong one. Should I name the two networks the same ssid, and if so what is the actual effect? Do the signals get confused, is the bandwidth affected, will this help my devices seamlessly move from one to the other, or is the ssid just a cosmetic thing that actually doesn't have any impact on this situation? Are there any other settings that I should configure to make my setup optimal?

    Read the article

  • Portforwarding Combine Several Ports

    - by kiraitachi
    Hi I got a Raspberry Pi at A.A.A.B in my local network and I have set up a DMZ on my router so that any incoming traffic that comes to my router gets redirected to my raspberry pi wich I can connect via NO-IP adress. The problem is that I want to set up portforwarding since i got several services running on my Pi like SSH, torrent webgui, webalbum, etc. I had this already done before long time ago, but I forgot a bit the syntax and cant get to set it up. Router Help says: The Application allows you to do port forwarding, but only have the ports open when data flowing out of the trigger ports. When a program sends data out on outgoing ports called trigger ports, the device then allows incoming data on the open ports specified in your port triggering configuration. 1.Trigger Port Start Trigger Port Start Specify the start port on the device that would trigger the device to open ports for incoming data. 2.Trigger Port End Specify the end port on the device that would trigger the device to open ports for incoming data. You can enter a port number the same as the trigger port start or enter a larger port number to specify a port range. 3.Trigger Traffic Protocol Type Select the trigger traffic type. Open Port Specify all the ports to be opened. It's content could be: A single port only. A port range only. Start open port number and end port number should be separated by "-" . Combined several single port and several port ranges. Each single port or port range should be separated by "," . Open Traffic Protocol Type Select the open traffic type. This are the fields: http://es.tinypic.com/view.php?pic=n5lv1k&s=8 I think this is the syntax 1-7999,8001-9090,9092-65535. But each time I want to add it gives me an error. Any ideas?

    Read the article

  • DD-WRT RIP2 Router mode configuration

    - by Eduardo
    Can anybody tell me why my wireless router only redirects traffic to ADSL modem when it is on Gateway mode? These are the configurations when it is on RIP2 Router mode: ADSL Modem: ------------ LAN IP: 10.1.1.1 Subnet mask: 255.0.0.0 RIP v2 enabled in both directions Route: destination: 192.168.1.0 Subnet mask: 255.255.255.0 Gateway: 10.1.1.2 Wireless Router (DD-WRT) ------------------------ WAN IP: 10.1.1.2 WAN Subnet mask: 255.0.0.0 LAN IP: 192.168.1.1 LAN Subnet mask: 255.255.255.0 Operating mode: RIP2 Router Static Route: Destination LAN NET: 10.0.0.0 Subnet Mask: 255.0.0.0 Gateway: 10.1.1.1 Interface: LAN & WLAN

    Read the article

  • snmp, how to retrieve ip connected to the router with MIB-II

    - by dany
    Hi all, I want to create a program that acts as manager and that queries the router (or sets a trap) to obtain the list of ip connected to it. My router has these functionalities: SNMP v1, v2c, built-in MIB-I, MIB-II agent. Is it possible to retrieve these informations quering the MIB-II agent of the router in a standard way (not vendor dependent)? Bye

    Read the article

  • Can't get Angular Dart Router to work

    - by JesterXL
    I've tried this syntax in AngularDart 0.11.0: Angular Dart passing data from route service into a controller module.value(RouteInitializerFn, configureRoutes); void configureRoutes(Router router, RouteViewFactory views) { print("configureRoutes"); views.configure({ 'login': ngRoute( path: '/login', view: 'login/login.tpl.html'), 'today': ngRoute( path: '/today', view: '/today/today.tpl.html') }); However, my routing function never seems to get called. I've used both a print statement and breakpoint to no avail. When I attempt to call it like so: WorkoutLoggerApplication(this.rootScope, this.router) { print("WorkoutLoggerApplication::constructor"); new Future.delayed(new Duration(seconds: 2), () { router.go("login", {}); }); } I get: Bad state: Invalid route name: login I've tried 0.10.0, but no dice. I've also tried 3 varieties of the new bind function format, both also don't seem to ever fire the routing function.

    Read the article

  • Why is my Internet connection randomly dropping?

    - by Jeanno
    Ever since I have installed 12.04 (clean install not an upgrade), i have been having a drop in the Internet connection. The drop in the connection can be anything from 15 seconds to about 3 mins, and then the connection comes back. This behaviour happens while I am actively browsing the Internet, or if I wake up the computer and open Firefox (sometimes I have connection and sometimes I don't) . Please note that when the internet connection is on, it is not slow (as speedtest.net results show) In the beginning, I thought it was a problem with the driver r8169 for my RTL8111/8168B Ethernet card, so I downloaded the r8168 from Realtek website, followed the detailed instructions (blacklisted r8169, changed the file to '.bsh' ...), but still the same problem persisted. So I switched to a wireless connection, and I got the same problem with internet connection dropping randomly. Any ideas? Thanks in advance Output from 'lspci -v' Code: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: f8000000-fa0fffff Prefetchable memory behind bridge: 00000000d0000000-00000000dbffffff Capabilities: [88] Subsystem: Dell Device 04a7 Capabilities: [80] Power Management version 3 Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [a0] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [140] Root Complex Link Kernel driver in use: pcieport Kernel modules: shpchp 00:01.1 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: f4000000-f60fffff Prefetchable memory behind bridge: 00000000c0000000-00000000cbffffff Capabilities: [88] Subsystem: Dell Device 04a7 Capabilities: [80] Power Management version 3 Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [a0] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [140] Root Complex Link Kernel driver in use: pcieport Kernel modules: shpchp 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 52 Memory at f6108000 (64-bit, non-prefetchable) [size=16] Capabilities: [50] Power Management version 3 Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+ Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) (prog-if 20 [EHCI]) Subsystem: Dell Device 04a7 Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at f6107000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 53 Memory at f6100000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel Capabilities: [130] Root Complex Link Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 Memory behind bridge: fa400000-fa4fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Dell Device 04a7 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 0000c000-0000cfff Prefetchable memory behind bridge: 00000000dc100000-00000000dc1fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Dell Device 04a7 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: fa300000-fa3fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Dell Device 04a7 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 0000a000-0000afff Memory behind bridge: fa200000-fa2fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Dell Device 04a7 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) (prog-if 20 [EHCI]) Subsystem: Dell Device 04a7 Flags: bus master, medium devsel, latency 0, IRQ 23 Memory at f6106000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge: Intel Corporation P67 Express Chipset Family LPC Controller (rev 05) Subsystem: Dell Device 04a7 Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> Kernel modules: iTCO_wdt 00:1f.2 RAID bus controller: Intel Corporation 82801 SATA Controller [RAID mode] (rev 05) Subsystem: Dell Device 04a7 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 42 I/O ports at f070 [size=8] I/O ports at f060 [size=4] I/O ports at f050 [size=8] I/O ports at f040 [size=4] I/O ports at f020 [size=32] Memory at f6105000 (32-bit, non-prefetchable) [size=2K] Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [70] Power Management version 3 Capabilities: [a8] SATA HBA v1.0 Capabilities: [b0] PCI Advanced Features Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) Subsystem: Dell Device 04a7 Flags: medium devsel, IRQ 5 Memory at f6104000 (64-bit, non-prefetchable) [size=256] I/O ports at f000 [size=32] Kernel modules: i2c-i801 01:00.0 VGA compatible controller: NVIDIA Corporation Device 0dc5 (rev a1) (prog-if 00 [VGA controller]) Subsystem: NVIDIA Corporation Device 085b Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at f8000000 (32-bit, non-prefetchable) [size=16M] Memory at d0000000 (64-bit, prefetchable) [size=128M] Memory at d8000000 (64-bit, prefetchable) [size=32M] I/O ports at e000 [size=128] Expansion ROM at fa000000 [disabled] [size=512K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Capabilities: [b4] Vendor Specific Information: Len=14 <?> Capabilities: [100] Virtual Channel Capabilities: [128] Power Budgeting <?> Capabilities: [600] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?> Kernel driver in use: nouveau Kernel modules: nouveau, nvidiafb 01:00.1 Audio device: NVIDIA Corporation GF106 High Definition Audio Controller (rev a1) Subsystem: NVIDIA Corporation Device 085b Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at fa080000 (32-bit, non-prefetchable) [size=16K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 02:00.0 VGA compatible controller: NVIDIA Corporation Device 0dc5 (rev a1) (prog-if 00 [VGA controller]) Subsystem: NVIDIA Corporation Device 085b Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f4000000 (32-bit, non-prefetchable) [size=32M] Memory at c0000000 (64-bit, prefetchable) [size=128M] Memory at c8000000 (64-bit, prefetchable) [size=64M] I/O ports at d000 [size=128] Expansion ROM at f6000000 [disabled] [size=512K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Capabilities: [b4] Vendor Specific Information: Len=14 <?> Capabilities: [100] Virtual Channel Capabilities: [128] Power Budgeting <?> Capabilities: [600] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?> Kernel driver in use: nouveau Kernel modules: nouveau, nvidiafb 02:00.1 Audio device: NVIDIA Corporation GF106 High Definition Audio Controller (rev a1) Subsystem: NVIDIA Corporation Device 085b Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at f6080000 (32-bit, non-prefetchable) [size=16K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 03:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30 [XHCI]) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at fa400000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] Latency Tolerance Reporting Kernel driver in use: xhci_hcd 04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 51 I/O ports at c000 [size=256] Memory at dc104000 (64-bit, prefetchable) [size=4K] Memory at dc100000 (64-bit, prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Endpoint, MSI 01 Capabilities: [b0] MSI-X: Enable- Count=4 Masked- Capabilities: [d0] Vital Product Data Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel Capabilities: [160] Device Serial Number 03-00-00-00-68-4c-e0-00 Kernel driver in use: r8168 Kernel modules: r8168 05:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6315 Series Firewire Controller (rev 01) (prog-if 10 [OHCI]) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at fa300000 (64-bit, non-prefetchable) [size=2K] I/O ports at b000 [size=256] Capabilities: [50] Power Management version 3 Capabilities: [80] MSI: Enable- Count=1/1 Maskable+ 64bit+ Capabilities: [98] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [130] Device Serial Number 00-10-dc-ff-ff-cf-56-1a Kernel driver in use: firewire_ohci Kernel modules: firewire-ohci 06:00.0 SATA controller: JMicron Technology Corp. JMB362 SATA Controller (rev 10) (prog-if 01 [AHCI 1.0]) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 19 I/O ports at a040 [size=8] I/O ports at a030 [size=4] I/O ports at a020 [size=8] I/O ports at a010 [size=4] I/O ports at a000 [size=16] Memory at fa210000 (32-bit, non-prefetchable) [size=512] Capabilities: [8c] Power Management version 3 Capabilities: [50] Express Legacy Endpoint, MSI 00 Kernel driver in use: ahci Note that my wireless card is not showing, I have the Ralink 3390 card (which apparently does not show up on Ubuntu for some reason), however I am able to connect to wireless network and connect to the internet (when it is working)

    Read the article

  • Wifi not working after a few minutes

    - by drtanz
    I'm using a few MacBooks and iPads connected to a router via WiFi. The problem is that a few minutes after they connect via WiFi the connection stops working. This happens on all devices. I went into the router settings by connecting via cable and everything seems in order. Connecting a laptop via cable to the router I can use internet as normal, the problem is only with WiFi. What can be the problem here? Here are the connected clients Connected Clients MAC Address Idle(s) RSSI(dBm) IP Addr Host Name Mode Speed (kbps) 14:10:9F:F3:48:D6 1 -36 192.168.0.5 Jeans-Air n 78000 14:99:E2:C6:41:10 1 -36 192.168.0.8 JeanGaleasiPad n 24000 Here's the router event log Mon Dec 30 04:12:30 2013 Notice (6) WiFi Interface [wl0] set to Channel 1 (Side-Band Channel:N/A)... Mon Dec 30 04:12:25 2013 Notice (6) WiFi Interface [wl0] set to Channel 1 (Side-Band Channel:5) -... Mon Dec 30 02:17:56 2013 Notice (6) WiFi Interface [wl0] set to Channel 40 (Side-Band Channel:36)... Mon Dec 30 02:16:04 2013 Notice (6) WiFi Interface [wl0] set to Channel 11 (Side-Band Channel:7) ... Mon Dec 30 01:59:26 2013 Notice (6) WiFi Interface [wl0] set to Channel 6 (Side-Band Channel:N/A)... Mon Dec 30 01:59:22 2013 Notice (6) WiFi Interface [wl0] set to Channel 6 (Side-Band Channel:2) -... Sun Dec 29 23:27:51 2013 Notice (6) WiFi Interface [wl0] set to Channel 1 (Side-Band Channel:N/A)... Sun Dec 29 23:27:49 2013 Notice (6) WiFi Interface [wl0] set to Channel 11 (Side-Band Channel:N/A... Sun Dec 29 14:32:55 2013 Critical (3) Started Unicast Maintenance Ranging - No Response received - ... Sat Dec 28 13:08:19 2013 Error (4) DHCP REBIND WARNING - Field invalid in response ;CM-MAC=1c:3e... Fri Dec 27 18:10:19 2013 Critical (3) Started Unicast Maintenance Ranging - No Response received - ... Fri Dec 27 16:08:55 2013 Error (4) Map Request Retry Timeout;CM-MAC=1c:3e:84:f1:6b:84;CMTS-MAC=0... Thu Dec 26 21:08:53 2013 Notice (6) WiFi Interface [wl0] set to Channel 11 (Side-Band Channel:7) ... Thu Dec 26 20:43:50 2013 Notice (6) WiFi Interface [wl0] set to Channel 11 (Side-Band Channel:N/A... Tue Dec 24 12:45:03 2013 Critical (3) Started Unicast Maintenance Ranging - No Response received - ... Tue Dec 24 04:55:52 2013 Error (4) Map Request Retry Timeout;CM-MAC=1c:3e:84:f1:6b:84;CMTS-MAC=0... Mon Dec 23 12:32:00 2013 Notice (6) TLV-11 - unrecognized OID;CM-MAC=1c:3e:84:f1:6b:84;CMTS-MAC=0... Mon Dec 23 12:32:00 2013 Error (4) Missing BP Configuration Setting TLV Type: 17.9;CM-MAC=1c:3e:... Mon Dec 23 12:32:00 2013 Error (4) Missing BP Configuration Setting TLV Type: 17.8;CM-MAC=1c:3e:... Mon Dec 23 12:32:00 2013 Warning (5) DHCP WARNING - Non-critical field invalid in response ;CM-MAC... Mon Dec 23 18:32:02 2013 Notice (6) Honoring MDD; IP provisioning mode = IPv4 Mon Dec 23 18:31:10 2013 Critical (3) No Ranging Response received - T3 time-out;CM-MAC=1c:3e:84:f1... Mon Dec 23 18:28:57 2013 Critical (3) Received Response to Broadcast Maintenance Request, But no Un... Mon Dec 23 18:28:25 2013 Critical (3) Started Unicast Maintenance Ranging - No Response received - ... Mon Dec 23 12:17:48 2013 Notice (6) TLV-11 - unrecognized OID;CM-MAC=1c:3e:84:f1:6b:84;CMTS-MAC=0... Mon Dec 23 12:17:48 2013 Error (4) Missing BP Configuration Setting TLV Type: 17.9;CM-MAC=1c:3e:... Mon Dec 23 12:17:48 2013 Error (4) Missing BP Configuration Setting TLV Type: 17.8;CM-MAC=1c:3e:... Mon Dec 23 12:17:48 2013 Warning (5) DHCP WARNING - Non-critical field invalid in response ;CM-MAC... Mon Dec 23 18:17:48 2013 Notice (6) Honoring MDD; IP provisioning mode = IPv4 Mon Dec 23 18:16:58 2013 Critical (3) No Ranging Response received - T3 time-out;CM-MAC=1c:3e:84:f1... Mon Dec 23 18:16:15 2013 Critical (3) Received Response to Broadcast Maintenance Request, But no Un... Mon Dec 23 18:15:43 2013 Critical (3) Started Unicast Maintenance Ranging - No Response received - ...

    Read the article

  • IPSec VPN's being dropped by router and will not re-establish

    - by David Gard
    We have 3 sites, with our two remote sites connection to head office via LAN-to-LAN VPN's. All 3 sites use DrayTek 2900's with firware version v3.3.1.1_RC2 (this is a release candidate that DrayTek suggested I try, but sadly it made no difference). The only way to re-establish the VPN's once they have been dropped is to restart the router. Head office is set to dial out to both sites, with both the 'Always on' and 'Enable PING to keep alive' (pinging a server in the remote offices) options ticked. However, at random intervals the VPN's drop, logging IKE_RELEASE VPN : Dial-out Profile Index = 7, Name = Shepton (for one connection, and '6' & 'Wincanton' for the other connection). I first tried swapping the router with one at another site, and then had all three replaced, but that failed to solve the problem. Is anyone aware of anything that could cause the VPN's to drop randomly like this? Thanks.

    Read the article

  • Using the Juniper EX3300 Switch as a router?

    - by Richard Whitman
    I have a Juniper EX3300 switch in a data center. And I have connected one of the uplink ports (ge-0/1/0) to my ISP's router. I want to configure it so that all the devices connected to ports in the same VLAN as ge-0/1/0 can access the Internet. I have done some research, and I haven't gotten anywhere really. I have configured the interface as follows: ge-0/1/0 { ether-options { no-auto-negotiation; link-mode full-duplex; speed { 1g; } } unit 0 { family inet { address xx.xx.xx.xx/32; } } } where xx.xx.xx.xx is the "Customer Router Port IP" assigned by my ISP. When I try to commit, I get the following error: Interface ge-0/1/0.0 not enabled for switching Can some one tell me what is the right way to configure it?

    Read the article

  • MTU, DSL router and stalling TCP

    - by user38843
    I am discovering stalling TCP connection problem. The problem arises when I try to scp stuff from remote system from my home network. My home network is connected to internet via PPPoE (ADSL+) and everything works perfectly once working from my home network. The ADSL router has MTU set to 1492 but with that setting the scp from remote system does not work - stalling! When I change the MTU on my router to 1500 the that scp works perfectly but internet accesses from my home network is very slow to most of the www sites - even local ones. Just wondering where the problem exists - my ISP blocking ICMP, etc? Thanks!

    Read the article

  • Trouble with setting up Mac SSH with TP-LINK router

    - by arxanas
    I have a Mac running OS X 10.7.2, and a TP-Link TL-WR740N (whose control panel looks like this). Remote Login is on in the Mac's System Preferences, and port 22 is set to forward on the router. I can access my Mac as a web server using the external IP on port 80, which I have set up through the same port-forwarding mechanism provided by the router, but when I try to ssh server@external-ip, it just times out after a long while. (The same thing happens when I try vnc.) I can, however, ssh and vnc successfully into that computer while I'm on the same network when using its internal IP. Since ssh appears to work and port forwarding appears to work, I can't figure out what's causing the problem. Does anyone have any idea what might cause this?

    Read the article

  • Cannot access a very specific site from my router

    - by DJDarkViper
    This is a problem for me because this site is important to me. It's MY website. And sadly my email is hosted on my site (which I cant access either) When I try to access my website when connected to my Linksys E3000 router, these days it simply just doesn't go through. When I ping it, its all Request Timed Out, and when I tracert C:\Users\Kyle>tracert blackjaguarstudios.com Tracing route to blackjaguarstudios.com [199.188.204.228] over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms CISCO26565 [192.168.1.1] 2 16 ms 15 ms 11 ms 11.4.64.1 3 11 ms 9 ms 11 ms rd1cs-ge1-2-1.ok.shawcable.net [64.59.169.2] 4 20 ms 21 ms 22 ms 66.163.76.98 5 37 ms 36 ms 35 ms rc1nr-tge0-9-2-0.wp.shawcable.net [66.163.77.54] 6 112 ms 84 ms 85 ms rc2ch-pos9-0.il.shawcable.net [66.163.76.174] 7 86 ms 89 ms 90 ms rc4as-ge12-0-0.vx.shawcable.net [66.163.64.46] 8 90 ms 84 ms 85 ms eqix.xe-3-3-0.cr2.iad1.us.nlayer.net [206.223.115.61] 9 97 ms 97 ms 99 ms xe-3-3-0.cr1.atl1.us.nlayer.net [69.22.142.105] 10 128 ms 128 ms 126 ms ae1-40g.ar1.atl1.us.nlayer.net [69.31.135.130] 11 101 ms 97 ms 96 ms as16626.xe-2-0-5-102.ar1.atl1.us.nlayer.net [69.31.135.46] 12 100 ms 97 ms 197 ms 6509-sc1.abstractdns.com [207.210.114.166] 13 * * * Request timed out. 14 * * * Request timed out. 15 * * * Request timed out. 16 * * * Request timed out. 17 * * * Request timed out. 18 * * * Request timed out. 19 * * * Request timed out. 20 * * * Request timed out. 21 * * * Request timed out. 22 * * * Request timed out. 23 * * * Request timed out. 24 * * * Request timed out. 25 * * * Request timed out. 26 * * * Request timed out. 27 * * * Request timed out. 28 * * * Request timed out. 29 * * * Request timed out. 30 * * * Request timed out. Trace complete. C:\Users\Kyle> SHAW Cable being my ISP. Figuring this was all something to do with some setting I made on the router, I reset the thing back to factory defaults. Nope. So I'm at a bit of a loss what to do here, as NO device (Computers, Laptops, Tablets, Phones, PS3/ 360, etc) can access my site or its features, so it's not just my computer either. But every other site is just fine. When I connect to my neighbors router, the site comes up just fine. And shes with SHAW as well. What should I do?!

    Read the article

  • Why is port 444 open on this router?

    - by TJ Thind
    I have a Cisco RV110W. I ran nmap at it from the outside and nmap reports that the router has tcp port 444 open. Yet there are no port forwarding rules specifying this port. It should as far as I can tell, be closed. There's even a service listening to that port which I can connect to through telnet. I threw some SNPP commands at it but the service doesn't respond to any of them so I don't believe it's SNPP. Does anyone have any idea why this particular router has tcp port 444 open? I haven't been able to find anything in the manual or on Cisco's website.

    Read the article

  • Linux router and firewall with IP accounting

    - by Andrew
    I'm working on a project to replace my organisation's aging Slackware gateway/router/firewall machine in our colo rack. Previously we used rc.firewall but we are now looking for something more modern and easily configurable. The requirements are: Act as a gateway router & firewall Port forwarding to a Terminal Server in the colo IP/traffic accounting, preferably accessible via SNMP (already using cacti for other servers) Possibility of acting as a PPTP server & routing these connections Is not an out-of-the-box Cisco product (don't have the finances or support to maintain it) I'd prefer to use Ubuntu or some other Debian-based distro but something that integrates everything we're looking for is certainly an option if it offers all the desired features and is easy to configure. Is there a simple set of packages that will provide me with the Firewall & Accounting features, or am I best served with a custom-built distro / other solution?

    Read the article

  • Connect server to router with workstation in between?

    - by letseatfood
    I have a server (9 yr old Dell with Ubuntu 10.04 Server Edition) and a workstation (Laptop with Vista) which are both connected to a router. The workstation is able to access the server via web browser for testing my web development projects. Since the server is old and does not have a wireless card, I am wondering if it is possible to connect the server directly to the workstation while maintaining the ability to connect to the server from the workstation. The reason is that the computers are in a separate room from the router and I am trying to limit the amount of wires on the floor, along with trying to avoid buying more hardware (like a wireless card). Thanks and I will be more than happy to clarify!

    Read the article

  • belkin wireless router connection drops for ~60sec every ~15 mins

    - by j j
    Hi, I have a belkin wireless-g router, model F5D7230-4. about every 10-15 minutes, for about 1-1.5 mins I won't be able to browse any web sites. during this period, I usually get replys from "ping google.com". maybe 4/5 times I'll get a reply, 1/5 times i don't. I have changed the router DNS entries from "get DNS server from ISP" to 8.8.8.8, google's DNS and that hasn't fixed the situation. This happens on several computers, running windows7, xp, ubuntu, and a mac, so it is definitely NOT an issue with a computer configuration. any ideas?

    Read the article

  • Port Forwarding on Actiontec GT704-WG Router Issues

    - by adamweeks
    I am trying to setup a server at customer's location that has the Actiontec GT704-WG DSL router. The port forwarding it not working at all. Here's the details: Server: OpenSuse Linux box with a static IP address of 192.168.1.200 Application running accepting connections on port 8060 Firewall disabled Local connections (within the network) working properly Router: Updated to latest firmware available DHCP range set to 192.168.1.69-192.168.1.199 to not have any conflicts with the server Firewall set to "off" Rule set in the "Applications" setting to forward 8060 TCP and UDP to 192.168.1.200 machine (I've tried using the "TCP,UDP" option as well as both individual options) I've also tried just simply putting the server in the DMZ to see if I could connect to anything, but still nothing. Looking for any clues before I call and waste hours explaining the issue to tech support.

    Read the article

  • SSH not working after Restoring Running-Config to a Replacement Cisco Router

    - by Kyle Brandt
    One of my Cisco routers died over the weekend, Cisco sent the replacement and I restored the the config using copy tftp: running-config. Everything seems to work fine but I can no longer ssh into the router (I can telnet). The connection is refused, so it isn't listening on port 22 it seems like. I had previously backed up the config by just doing ssh router 'show run' > backup_config from my workstation. So: Is there anything wrong with my method of backup vs copy running-config tftp:? I know I haven't given any debug information, but is there something typical I need to do to get ssh working?

    Read the article

  • Connecting switch to switch to router

    - by elated
    Hello, Not sure if this is the right place to ask this question. But I have a router which connects to the internet. Now I have a switch connected to this router. I added a lot more computers so I added another switch and connected it to the first switch using a cross-over cable. As soon as I connect it to the first switch, my lights in first switch start blinking like crazy and my entire network simply stops working. The minute I remove the second switch's wire, its all fine again. What could be the problem?

    Read the article

  • BGP Router reccomendations for simple redundancy [closed]

    - by Jona
    We have two sites that each have an internet connection and have a dedicated dark fibre between them. Each site has it's own IP space and we have an AS number. We're looking to be resilient to failure of the internet connection to either site and so need to buy a pair of approriate routers. Requirements are: Able to run 2 bgp sessions (one with the ISP, one with the other site router) Option to take a full table from the upstream ISPs would be nice. Able to provide HA gateways on the LAN side (e.g. 192.168.0.254 will automatically migrate if it's host router lost power) A dedicated device rather than a server running Linux / BSD Not crazy expensive. Any help / advice much appreciated.

    Read the article

  • My D-Link Router is only allowing one connection

    - by Blaze
    My Router (Model: DI-624) is only allowing one wireless connection to one laptop. The other laptop is stuck hanging at connecting to the Internet I have the SSID set as "Pedro-Home" and is using a WPA PSK secured password. I have set the router using "Blaze-PC" while wired. Both Laptops critically need the Internet. > Dynamic DHCP Client List > > Host Name IP Address MAC > Address Expired Time > Blaze-PC 192.168.0.100 70-f1-a1-ff-39-a8 Apr/21/2011 17:49:14 > pedro 192.168.0.105 00-26-82-c8-47-25 Apr/21/2011 17:50:05 <<This computer isn't connecting.

    Read the article

  • Remote desktop from internet to windows 7 box via linksys router

    - by larryq
    Hi everyone, I have a linksys wrt54g router and a windows 7 box at home I'd like to be able to remote desktop into from work. Would it be possible for someone to point me in the right direction on what I need to configure to get this working, both on the router and on the win 7 box? I'm sure there are a lot of little steps involved. Ideally I'd like to set it up so that only my work IP address can get through to the win 7 machine. Thanks very much for any pointers and links!

    Read the article

< Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >