Search Results

Search found 13891 results on 556 pages for 'maybe homework'.

Page 421/556 | < Previous Page | 417 418 419 420 421 422 423 424 425 426 427 428  | Next Page >

  • Running computer from separate room

    - by Dan
    I want my computer to be in the basement, but to use it on the first floor. Which cables should I run through the floor? Can some be wireless or other methods? Here are some of the options I've thought of: Basic: Run DVI, usb (mouse), usb (keyboard), and audio cable (4 cables) USB Hub option: Run DVI, and 1 usb, then using a usb hub split it into mouse, keyboard, maybe even audio (2-3 cables) HDMI Option: If I get a new video card and monitor that supports HDMI, would I be able to run both audio and video through it? Would the monitor have to have an audio out? Also there is a lot of extra bandwidth in the HDMI cables, could I send two monitors on 1 cable or would I have to use 2 cables? How about sending mouse/keyboard through the HDMI cable? I see a lot of monitors with USB hubs built in, but I assume I'd still have to wire HDMI + 1 USB cable to use the USB hubs? X Terminal Machine/Thin Client: I don't really know much about this option. Not sure if it would allow me to run graphics acceleration and watch movies, does anyone know more details about what this would allow me to do? Other options: Any other ways to do this? Can any of this be wireless?

    Read the article

  • Lost Windows 7 boot after EasyBCD with EFI

    - by drent
    I've got a Lenovo Y580 with a 64GB SSD and a 1TB HDD setup using GPT and setup to boot from (U?)EFI. I was trying to get my Linux Mint installation on the Windows boot manager using EasyBCD (I didn't realise EFI but it wiped my boot partition/loader and I cannot seem to get Windows back (and I still can't get a bootable Linux Mint). Using the System Recovery utility, Startup Repair can't "see" windows (it might be because I'm using a 7 Pro disk to recover Home Premium?). In command prompt, Bootrec tools don't do anything and bootsect can't run because it says that it's for BIOS only and I've booted with EFI. I can see the EFI data on the 200mb SSD partition using diskpart but I don't know how to add Windows back onto whatever bootloader I have/need. At the moment the only options I can see are: Do a fresh install of Windows and hope that the setup remains as fast as the default one (the SSD is some kind of cache for Windows but I can't quite see how it works given that the rest of the SSD is unpartitioned space). This seems like overkill given that Windows was working fine til EasyBCD deleted it. Try forcing BIOS mode and see if that somehow magically fixes things Try converting from GPT to MBR to try and use the bootrec/bootsect tools (and maybe back again) which seems like a really bad idea. Anyone have any ideas?

    Read the article

  • Todo/task manager for android and desktop linux

    - by RiaD
    I'm looking forward to Task/ToDo Manager. It should work under Android, Linux(or Web). If it's very cool, one of them is OK too, Android is preferable in this situation. Necessary features: Russian or English language Possibility to mark task as finished Interesting features: (I want as more, as possible, while it's OK, if some of them isn't avaliable) Nice and easy-to-use interface Possibility to choose finish time for task. After that it's showed as overdue. Possibility to choose start time for task. Before it task is inactive and maybe shown or hide Possibility to add nested tasks. Task marks completed when all sub-tasks are completed. Possibility to make dependencies. If A depends on B, and B isn't finished yet, A is inactive as in third feature. Possibility to create task in a moment without fill-all-this-forms Syncronization between version(Android to linux or Android to web) Notification (on Android only) Features, that I'm not interested in: Creating more than one todo list sharing ToDo's I've seen couple of managers. Best I've seen now is Task Coach for Linux, but I don't very like its interface, and there is no version for Android.

    Read the article

  • Hard Disk based storage library

    - by Ryan M.
    We have a Tandberg T24 tape device to handle all of our long term backups right now. We decided that we're not backing up nearly everything that we would like to and that we still have a lot of vulnerabilities. To get to where we want to be, we're going to have to back up a lot more servers than we're currently doing. All of our internal servers have some sort of directly attached drive (I.e. LaCie Raid box or a simple portable hard drive) doing backups, but what we want to do is get those backups off-site. The current tape drive is directly attached via SCSI to a Windows Server 2008 File Server. So to back up anything to tape, it has to be funneled through the File Server. With the current increase that we have planned, I don't think that funneling everything through the File Server is the right course of action and I'm thinking that maybe a second backup device would be more appropriate. I would like your input on a couple of ideas. 1) Doing HDD instead of tape. Tape is hard to deal with. We have a regular rotation cycle, so they don't need years and years of shelf life, so I'm wondering if something HDD-based would be better. 2) Something accessible over the network. Instead of having the device directly attached to one specific machine, have it available to all the servers over the network. Our File Server is a 12-disk raid 6 set up.. I was thinking something like that, but with no raid involved, all disks are stand alone so they can be used/installed/removed on an individual basis. Does any such thing exist? Thanks for your ideas. I'm really interested to hear about some of the solutions you guys are using..

    Read the article

  • Please help me get rid of asmonitor.exe

    - by LCD Fire
    It might be silly and I trully apologize if the question is not apropriate here, but I have really tried and got to nowhere. I have a windows xp startup error which indicates something about asmonitor.exe program from the ActualSpy keylogger. I had installed but removed ActualSpy keylogger using Superantispyware or something close. I have searched the registries and found a asmonitor entry deleted. I looked at startup programs and can not find the asmonitor program. In addition, I searched the c: drive using regular explorer search and searched using ESET NOD32 antivirus. In each case I cannot find the application... I have even looked at startup programs using msinfo32 command. msconfig-startup NOTHING! it drives me crazy! I can't get rid of it. it is still showing up at windows startup! Where do I find this little program? where is it located? I don't want it to keep showing up. I don't want programs that can do it.. or maybe free ones. But I prefer manual solutions. aren't are any?

    Read the article

  • System With Two Network Adapters [closed]

    - by Synetech inc.
    Hi, My system has a NIC (Marvell Yukon) built-into the motherboard, but I also have a D-Link (RealTek) card. I figure that using the D-Link and disabling the Marvell makes the most sense, though I'm wondering if maybe the built-in one has better throughput (not that my Internet connection is so fast). Also, I'm wondering about the merits of using both at the same time. My router has four ports and I have experimented with enabling and plugging both NICs into the router. I was able to connect to the Internet, but the pattern of usage seemed irregular (which adapter was chosen for the transfer and any given point). I also considered bridging the two, but am having difficulty in finding out what exactly creating network bridge does in the context of the Windows Network Connections window. I am familiar with the concept of connecting networks, so it seems to me that birding two connections on the same segment is pointless at best (and can cause problems like loops?) Does anyone have any tips on what to do if a system has more than one NIC and any clarification on the bridge option? Thanks a lot.

    Read the article

  • What do Windows 8 Refresh and Reset my PC really do?

    - by Jerry Nixon
    In Windows 8 I can reset everything and reinstall Windows. I assume this will clear my drive and start from scratch? Is that right? Does this create a Windows.old folder? I see this dialog, but aren't my settings and preferences saved in the cloud? If I screw up my settings and reset like this, are my settings also refreshed back to defaults? Since I use SkyDrive to sync my files, my personal files are safe, right? Also, in Windows 8 I can refresh my PC without affecting files. Are my desktop and/or Windows store apps uninstalled when I refresh my PC? I see this dialog, but I still am not sure. For example, when it says apps are "kept" does that mean I don't have to buy them again or are they installed after the refresh is over for me? I assume "from disk" means desktop apps? Or maybe corp apps? What would motivate a user to choose between these two?

    Read the article

  • How can I rapidly switch hosts?

    - by EAMann
    I'm in the process of migrating a forum setup from one version of the software on one machine (older shared Windows host) to a new VPS (Windows Server 2008). To install the software, I used my hosts file to temporarily point the domain at the new IP address. To see the old site, I obviously re-edit the hosts file to remove the reference. But this leaves me constantly adding/removing a # from my hosts file just so I can switch back and forth between the two servers. Is there a way to do this more rapidly? I've found a handful of toggling batch scripts, but all they do is automate the addition/removal of the # character ... so there's still a noticeable lag where I have to repeatedly hit F5 to force my system to detect the new settings. Ideally, I could view both servers at the same time on the same machine. Maybe one through a regular browser session and one through some kind of a proxy. Unfortunately, I don't have the first idea how to set that up. Ideas?

    Read the article

  • Scripting around the lack of user:password@domain url functionality in jscript/IE

    - by Idiomatic
    I currently have a jscript that runs a php script on a server for me, dead simple. But... I want to be atleast somewhat secure so I setup a login. Now if I use the regular user:password@domain system it won't work (IE decided it was a security issue). And if I let IE just remember the password then it pops up a security message confirming my login every time (which kills the point of the button). So I need a way to make the security message go away. I could lower security settings, which tbh I am fine with but nothing seems to make it fuck off (there might be some registry setting to change). Find a fix for jscript that will let me use a password in the url. There used to be a regedit that worked for older systems which allowed IE to use url passwords (not working on my 64bit windows7 setup) though I doubt that'd have helped jscript anyways (since it outright crashes). Use an app other than IE. Inwhich case I'm not sure how to go about it, I want it to be responsive and invisible so IE was a good choice. It is near instant. Use XMLHttpRequest instead of IE directly? May even be faster but I've no idea if it'd help or just have the same error. Use a completely different approach. Maybe some app that can script website browsing. var args = {}; var objIEA = new ActiveXObject("InternetExplorer.Application"); if( WScript.Arguments.Item(0) == "pause" ){ objIEA.navigate("http://domain/index.html?pause"); } if( WScript.Arguments.Item(0) == "next" ){ objIEA.navigate("http://domain/index.html?next"); } objIEA.visible = false; while(objIEA.readyState != 4) {} objIEA.quit();

    Read the article

  • How can I prevent a DDOS attack on Amazon EC2?

    - by cwd
    One of the servers I use is hosted on the Amazon EC2 cloud. Every few months we appear to have a DDOS attack on this sever. This slows the server down incredibly. After around 30 minutes, and sometimes a reboot later, everything is back to normal. Amazon has security groups and firewall, but what else should I have in place on an EC2 server to mitigate or prevent an attack? From similar questions I've learned: Limit the rate of requests/minute (or seconds) from a particular IP address via something like IP tables (or maybe UFW?) Have enough resources to survive such an attack - or - Possibly build the web application so it is elastic / has an elastic load balancer and can quickly scale up to meet such a high demand) If using mySql, set up mySql connections so that they run sequentially so that slow queries won't bog down the system What else am I missing? I would love information about specific tools and configuration options (again, using Linux here), and/or anything that is specific to Amazon EC2. ps: Notes about monitoring for DDOS would also be welcomed - perhaps with nagios? ;)

    Read the article

  • Mysql server high trafic makes websites really slow or unable to load

    - by Holapress
    Lately we have been having a lot of problems with our mysql server, from websites being really slow or even unable to load them at all. The server is a dedicated server that only runs our mysql database. i have been running some test using a profiler (JetProfiler) and tool to stress test (loadUI). If I use loadUI to connect with 50 simultaneous connections to one of our websites that runs a resently big query it will already make the website be unable to load. One of the things that makes me worried is that when I look at Jetprofile it always shows a Treads_connected of 1.00 and it seems that when it hits around 2.00 that I'm unable to connect. The 3 big peaks are when I run a test with loadUI, first one was 15 simultaneous connections wich made it still able for me to load the website but just really slow, the second one was 40 simultaneous connections which already made it impossible to load and the third one was with 100 connection which also didn't make it load anymore. Another thing that worries me is that in JetProfiler it says all the queries that get used are full table scans, could this maybe be the problem? The website I run as a test runs 3 queries, one for a menu that outputs around 1000 rows, one for the adds that has around 560 rows and a big one to get posts that has around 7000 rows (see screenshot bellow) I also have monitored the cpu of the server and there seems to be no problem there, even when I make a lot of connections with loadui the cpu stays low. I can't seem to figure out what is the main cause of the websites being unable to load when there is a high amount of traffic, if anyone has other suggestions for testing or something that might cause the problem please let me know.

    Read the article

  • Find which files an apache process is writing to?

    - by Haluk
    We have this apache process which becomes io-bound time to time. Using atop, we can see it is a write operation. Using lsof -p <PID> we can see a list of files open by the httpd process. First we thought "log" files must be the problem. So we turned them off just to test. However write operations still continues. We will continue testing a few other things. For instance we use php session variables a lot. Maybe php session files are getting all the writing. But is there a way to quickly identify files which get written to by the httpd process? This way we can focus our efforts on those files. UPDATE: We used the strace command as suggested. Here are two lines from the output. write(23, "\27\0\0\0\3SET CHARACTER SET utf8", 27) = 27 write(23, "\17\0\0\0\3SET NAMES utf8", 19) = 19 We do not have a mysql process on this server. So is strace also showing what is being written to an ethernet port? UPDATE2: During high io load, the process which consumes most of the write resources gives the following output to strace -e trace=write -p <PID>: --- SIGCHLD (Child exited) @ 0 (0) --- write(9, "!", 1) = 1 write(19, "OPTIONS * HTTP/1.0\r\nUser-Agent: Apache (internal dummy connection)\r\n\r\n", 70) = 70 However I cannot figure out where these are being written to.

    Read the article

  • Windows Server 2008 IIS7 - page requests randomly hang or timeout

    - by seb835
    I've just installed a fresh copy of Windows Server 2008 x64 with IIS7 and PHP (fast CGI). However, I'm noticing that after moving my web site from a similarly specified machine to this one, I'm getting issues. The issue seems to be that randomly, as I'm clicking through the web pages being served, the browser will suddenly hang saying "waiting for mysite.com...". Sometimes the page will then timeout, or finally resolve after 20 to 30 seconds, but maybe missing the CSS style sheet. Very strange, as this is the only website installed on this new server, and only myself using/testing it. Server is installed in the same data centre below the old server. Has anyone else had a similar problem? I tried increasing the max workers pool to 10 (from 1), but this has no effect. Seems to happen most frequently after 1 or 2 minutes of inactivity on the website, then trying to load/refresh a web page. Many thank for any info and help. Kind Regards, Seb

    Read the article

  • 64-bit Windows 7 gets stuck on logo screen on bootup

    - by Richard B
    I've had a PC running Windows 7 in my office which I'm not using at the moment (cause I'm working elsewhere as a consultant atm), I'm only accessing the PC using Team Viewer (http://www.teamviewer.com/) which means the PC has been running for quite some time now. I've restarted it maybe twice a week though. A few days ago I couldn't access it using Team Viewer and when I got to the office the screen was black with only the mouse pointer showing. The PC has four hard disks, three of them (all 1Tb) is using RAID 5. This is what I've done so far: I reboot and everything seems to load correctly. I get to a screen that gives me two choices - boot Windows normally or perform a startup repair. Choosing to boot Windows only gets me to the Windows 7 logo screen which only animates over and over again. Choosing to repair gets me to the repair screen that "checks for problems" and then it gets stuck on the "Attempting repairs..."-screen (I let it run for about 24 hours before giving up). What is the next step to take? I don't have any backups and no system restore points saved. I can access files and folders through a terminal window using a Windows 7 DVD so I guess nothing is lost yet... Please help me, thanks!

    Read the article

  • How do I configure IIS to allow access to network resources for PHP scripts?

    - by Dereleased
    I am currently working on a PHP front-end that joins together a series of applications running on separate servers; many of these applications generate files that I need access to, but these files (for various reasons) reside on their parent servers. If I, from the command line, issue a bit of script such as: <?php var_dump(glob("\\\\machine-name\\some\\share\\*")); I will get the full contents of that directory, proving that there's no problem programmatically with PHP reading the contents of a UNC share. However, if I try to execute the same script from the web server, I get an empty array -- more specifically, if I use more explicitly functions designed to "open" a directory like it was a file, I get access errors. I believe this to be a permissions issue, but I am not a server/network administrator type, so I'm not sure what I need to do to correct this and get my script running, and the links I've checked out have not been a terrible amount of help, perhaps due to my background, or lack thereof as far as IIS is concerned, coupled with the fact that we are not actually using .NET for this. Relevant Stats: Windows Server 2008 Standard SP2 IIS 7.0 PHP 5.2.9 I will be connecting to two types of servers: a few other nearly-identical Server 2008 machines, and a machine running embedded XP. Links that have not been particularly helpful but maybe I am just misreading: http://support.microsoft.com/?id=306158 http://support.microsoft.com/kb/207671/EN-US/ http://support.microsoft.com/kb/280383/

    Read the article

  • Is there a way to log commands that a user runs in Windows 7?

    - by camster342
    I manage a large enterprise environment, and while we try to advise users not to, there are inevitably users that need to have local admin access to their machines. The problem is that some of these users like to "fiddle" and sometimes screw up their machines in "wonderful" ways. Is there an easy way to log what a user does on a machine, specifically in the command prompt? Maybe there is 3rd party tools I could use to log this information? With Linux that I used to use in past ages, you could look at a users bash history file to see what commands they have run. While I realise that specific log could also be altered by the user if they wanted to cover their tracks, that is the sort of log I'm looking for. If there are other ways I can also log what other system configuration type changes they make as well (not necessarily command line based), that's also useful. I know about event/system logs and so on, but that doesn't necessarily catch all the information I need to figure out how the user has buggered their machine this time.

    Read the article

  • How would I change the DocumenRoot on the version of Apache that came pre-installed on my Mac OS X s

    - by racl101
    OK, so I want to take advantage of the Apache server that comes installed on my Mac OS X system (which means, I would like not to have to install my own version of Apache since I might as well tryto use what comes bundled), and as such, I went to change some settings in the configuration file: /etc/apache2/httpd.conf Namely, I changed the these two lines: DocumentRoot "/Users/myusername/Sites" <Directory "/Users/myusername/Sites"> So that they initially pointed to a folder in my Dropbox folder (so I could have my docs sync to my Dropbox): DocumentRoot "/Users/myusername/Dropbox/public_html" <Directory "/Users/myusername/Dropbox/public_html"> That didn't work. So then I figured, ok maybe it was too much to ask to make folder in my Dropbox be my document root. So then I thought, what if I make the Document root another folder of my choosing like so: DocumentRoot "/Users/myusername/dev-sites/public_html" <Directory "/Users/myusername/dev-sites/public_html"> and that didn't work either. After looking within the httpd.conf file for clues it seems that only two directories appear to work as Document root paths for the Apache that comes bundled with Mac OS X: /Users/myusername/Sites (or ~/Sites) and /Library/WebServer/Documents/ But trying to use any other directories didn't seem to work. I would get 403 errors on my browser. I was wondering if there was some other settings to change on the httpd.conf file or any permissions to set to make this work. Any help would be appreciated and many thanks in advance.

    Read the article

  • What I should know about memory management?

    - by bua
    first of all: I don't use stackadmin or similar so please don't vote for moving there, I'm reading man top and paper "what every programmer should know about memory ..." I need really simple explanation like for retard ;) Having following top dump: top - 11:21:19 up 37 days, 21:16, 4 users, load average: 0.41, 0.75, 1.09 Tasks: 313 total, 5 running, 308 sleeping, 0 stopped, 0 zombie Cpu(s): 0.4%us, 0.6%sy, 0.9%ni, 96.2%id, 0.1%wa, 0.0%hi, 1.9%si, 0.0%st Mem: 132103848k total, 131916948k used, 186900k free, 54000k buffers Swap: 73400944k total, 73070884k used, 330060k free, 13931192k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 3305 tudb 25 10 144m 52m 940 R 6.0 0.0 1306:09 app 3011 tudb 15 0 71528 19m 604 S 3.3 0.0 171:57.83 app 3373 tudb 25 10 209m 93m 940 S 3.0 0.1 1074:53 app 3338 tudb 25 10 144m 47m 940 R 2.7 0.0 780:48.48 app 4227 tudb 25 10 208m 99m 904 S 1.3 0.1 198:56.01 app 8506 tudb 25 10 80.7g 49g 932 S 2.0 39.6 458:31.22 app I'm wondering what is: RES (my expl. physical memory consumption ? see 49GB) VIRT (memory mapped disk to cache? see 80GB) SHR (shared pages?) Swap: (is this cached label - for memory mapped disk into swap cache?) Should sum of RES give MEM: X used? or maybe sum of VIRT?

    Read the article

  • My Samsung R480 laptop freezes for short and inconsistent periods of time.

    - by anonymous
    I have a Samsung R480 laptop running Windows 7. It's great, I love it to death, but every so often it'll start having, for lack of a better term, "hiccups". It would freeze completely, emit a loud BZZZZZZT from the speakers (think when a video freezes and the sound gets stuck), then return to working order all in a span of 0.5~2 seconds. It has happened while I was playing Mass Effect, while I was watching both HD and non-HD videos, and while I was surfing the internet (which I've noticed while watching YouTube videos and playing Entanglement, but also noticed while using Facebook, minus the buzzing sound). My Initial hypothesis was that my GPU or CPU were overheating as it would shut down while playing Mass Effect, but when I turned off my WiFi card hardware using [fn + F9], the problem was resolved. As I currently see it, it could be a problem with my CPU, my WiFi card, or my sound card. It could also be a software related issue, possibly an ill-functioning process. It could be chrome related. A memory leak from chrome maybe? Does anyone know how to resolve this?

    Read the article

  • Manual Http error response code in non-existent folder via routing

    - by Slytherin
    Apache server running on ubuntu-like linux I am getting unexpected behaviour when i try to manually send error response. If my .htaccess is responsible for the error response , then appropriate error document is loaded and displayed , with according response code in browser console. However , if my router is origin of the response code , then i get blank screen , but correct response code. .htaccess looks like this RewriteEngine On # RewriteBase / RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule !\.(css|js|icon|zip|rar|png|jpg|gif|pdf)$ index.php [L] ErrorDocument 404 /err/404.html ErrorDocument 403 /err/403.html ErrorDocument 500 /err/500.html part of my router that sends the response is the following header("HTTP/1.1 403 Forbidden"); trying this format didnt help either header("HTTP/1.1 403 Forbidden", TRUE, 403); I also tried HTTP/1.0. Furthermore i was thinking that maybe relative path to error page might be an issue , but discarded this idea after attempting to access a document that is forbidden via .htaccess EDIT I should also point out , this scenario happens when URL for not-existing article is requested. Is it possible that Server is looking for a .htaccess file in a folder based on URL ? Eg: domain/blog/non-existent , is server looking for blog folder ? I am specifically asking this because there is no blog folder

    Read the article

  • Computer wont start, just blinks on and off

    - by Ryan
    This is really strange. I had a comp that was working fine for over a year, then suddenly it started to shut off, it got so bad that I press the power button and in around 30 secs while booting windows it would shut off, then 20 secs... then 10 secs, then it refused to start all together. So I bought a new PSU (850w Thermaltake, the old one was 550w corsair) thinking that was the problem, I fitted the new PSU now and its the same thing, I press the power button and my fans start for a split second (they have led lights on them, so the lights come on) and then everything goes off again. I thought maybe it was my power button that was loose on my comp, luckily I had another chassis near by so I disconnected the powerSW from the old one and put ran the powerSW from the new chassis, press the power on the new chassis and same thing, it blinks for a split second and off again. Double checked connections from the PSU to the cpu power as well as board mobo power, its tight. It's pretty unlikely both the PSUs have the same exact problem so am lost... Suggestions?

    Read the article

  • How best to handle end user notification in the event of system failure incl. email?

    - by BrianLy
    I've been asked to research ways of handling end user notifications when systems such as email are experiencing problems. Perhaps an example will make this a little clearer. We have a number of sites in different countries. Recently email was impacted at one of the sites, but it could have been a complete network outage. Information was provided by phone to local IT managers at the site but onward communication was slower than some would have liked. It seems like almost everyone at the site has a personal mobile phone which could receive text messages, and perhaps access a remote website with postings on the situation. However managing and supporting a system to text people on these relatively infrequent occasions would be very costly to do internally. What are other people doing to handle situations like this? Some things I've thought of include: Database of phone numbers to text. Seems costly and not very easy to maintain for an already stretched IT group. Is there an external service that would let you do this policies? Send voicemail message to all phones on site. Maintain an external website. This would not work in all situations (network failure), and there is a limit on the amount of info that can be posted externally. A site outage could be sensitive information in some situations. How could the site be password protected? Maybe OpenId/Facebook connect would work. Use a site like Yammer.com which is publicly accessible but only by people with a company email address. Anyone using this for IT outage notifications? To me it looks like there is no clear answer, and that there are solutions for some subsets of users. To be comprehensive a number of solutions would need to be combined. Any additional thoughts or recommendations? What worked or didn't work for your organization?

    Read the article

  • What does the 'Burst Rate' stat mean in HDTune?

    - by UpTheCreek
    I recently upgraded my laptop's v slow hard drive to a seagate momentus 7200. Everything is working fine, but I'm a bit confused by these benchmark results: The burst rate is significantly less than the Maximim transfer rate, and not much higher than the normal minimum (if you ignore the spikes). What's going on here? On the HDtune website it defines Burst Rate as: ...the highest speed (in megabytes per second) at which data can be transferred from the drive interface (IDE or SCSI for example) to the operating system. Which begs some questions... e.g. if this is the highest, then how did the bechmarking tool record the 103MB/sec maximum? And if this really is the true maximum, then where is the bottleneck? The laptops SATA interface is on an Intel 82801GBM southbridge controller. When I check in hardware manager, I see that it's driver is iaStor.sys from 2005. Maybe that's the issue? I'll look for a newever version, but any insights would be appreciated. Thanks

    Read the article

  • How do I setup a proper VPN for my friends to play LAN games AND give them internet access?

    - by Gizmo
    I'm trying to setup a VPN on my local network, but everyone who connects to me DOES have access to my laptop but not to the internet or other devices on the network. How can I properly configure my VPN on windows to work correctly (giving internet + access to all devices on my network to the remote pc)? Or is there software on windows which makes creating a VPN server easier? or maybe a VMWare image linux vpn server? I can't find any of those! My requirement is that my friends don't have to install additional software, they have to be able to connect with default windows stuff. My OS is Windows 8 Standart edition (not pro or enterprise) OEM. Most of my friends have also windows 8, some windows 7. Extra info: My device is DMZ'ed (Demilitarized Zone, [disabled NAT on my device so it's accessible on the WAN]) I can access files, websites and services on other devices on my network, and all devices can access file shares, website and all other services on my device When enabling VPN everything works except the client is unable to get internet access or access to any device on my network, client has only access to my device.

    Read the article

  • Why does lighttpd keep static files in cache, even when modified on disk ?

    - by Pixelastic
    I am using lighttpd to serve static files. I have a bunch of images in a dir that I regularly update. This will change the file content (and filesize) as well as the modification date, but not their filename. When I access the files through http, the updates are not taken into account and lighty serves the old file. I can manually rename the file to something different, then lighttpd will return a 404 error, and if I rename my file back, I will get the correct updated version. Seems like lightty is using some kind of cache mechanism of its own (which is fine) to return static files. Unfortunatly, it seems that this mechanism doesn't update itself when files are modified. I checked through Wireshark, and my browser is really doing a request to the file, this is not a browser caching issue. It returns a 200 OK when requesting it from an empty cache, and a 304 Not Modified otherwise, as expected. But the file is returned with a wrong Last-Modified header that do not reflect the real last modification date. Maybe there is some config directive that I am not aware of ? I would like the files returned by lighty to reflect the changes made on disk directly, or at least being able to invalidate its cache.

    Read the article

< Previous Page | 417 418 419 420 421 422 423 424 425 426 427 428  | Next Page >