Search Results

Search found 17860 results on 715 pages for 'virtual pc'.

Page 427/715 | < Previous Page | 423 424 425 426 427 428 429 430 431 432 433 434  | Next Page >

• Apache won't accept external requests

  - by Eric

  I am running Apache 2.2 on windows and I would like to access it remotely. Currently I can only access it from my local machine. I know the problem is not port forwarding because I tested it with other web servers (written in python). My httpd.conf file is below. I installed apache with the PHP installer. # # This is the main Apache HTTP server configuration file. It contains the # configuration directives that give the server its instructions. # See <URL:http://httpd.apache.org/docs/2.2> for detailed information. # In particular, see # <URL:http://httpd.apache.org/docs/2.2/mod/directives.html> # for a discussion of each configuration directive. # # Do NOT simply read the instructions in here without understanding # what they do. They're here only as hints or reminders. If you are unsure # consult the online docs. You have been warned. # # Configuration and logfile names: If the filenames you specify for many # of the server's control files begin with "/" (or "drive:/" for Win32), the # server will use that explicit path. If the filenames do *not* begin # with "/", the value of ServerRoot is prepended -- so "logs/foo.log" # with ServerRoot set to "C:/Program Files (x86)/Apache Software Foundation/Apache2.2" will be interpreted by the # server as "C:/Program Files (x86)/Apache Software Foundation/Apache2.2/logs/foo.log". # # NOTE: Where filenames are specified, you must use forward slashes # instead of backslashes (e.g., "c:/apache" instead of "c:\apache"). # If a drive letter is omitted, the drive on which httpd.exe is located # will be used by default. It is recommended that you always supply # an explicit drive letter in absolute paths to avoid confusion. # # ServerRoot: The top of the directory tree under which the server's # configuration, error, and log files are kept. # # Do not add a slash at the end of the directory path. If you point # ServerRoot at a non-local disk, be sure to point the LockFile directive # at a local disk. If you wish to share the same ServerRoot for multiple # httpd daemons, you will need to change at least LockFile and PidFile. # ServerRoot "C:/Program Files (x86)/Apache Software Foundation/Apache2.2" # # Listen: Allows you to bind Apache to specific IP addresses and/or # ports, instead of the default. See also the <VirtualHost> # directive. # # Change this to Listen on specific IP addresses as shown below to # prevent Apache from glomming onto all bound IP addresses. # #Listen 12.34.56.78:80 Listen 80 # # Dynamic Shared Object (DSO) Support # # To be able to use the functionality of a module which was built as a DSO you # have to place corresponding `LoadModule' lines at this location so the # directives contained in it are actually available _before_ they are used. # Statically compiled modules (those listed by `httpd -l') do not need # to be loaded here. # # Example: # LoadModule foo_module modules/mod_foo.so # LoadModule actions_module modules/mod_actions.so LoadModule alias_module modules/mod_alias.so LoadModule asis_module modules/mod_asis.so LoadModule auth_basic_module modules/mod_auth_basic.so #LoadModule auth_digest_module modules/mod_auth_digest.so #LoadModule authn_alias_module modules/mod_authn_alias.so #LoadModule authn_anon_module modules/mod_authn_anon.so #LoadModule authn_dbd_module modules/mod_authn_dbd.so #LoadModule authn_dbm_module modules/mod_authn_dbm.so LoadModule authn_default_module modules/mod_authn_default.so LoadModule authn_file_module modules/mod_authn_file.so #LoadModule authnz_ldap_module modules/mod_authnz_ldap.so #LoadModule authz_dbm_module modules/mod_authz_dbm.so LoadModule authz_default_module modules/mod_authz_default.so LoadModule authz_groupfile_module modules/mod_authz_groupfile.so LoadModule authz_host_module modules/mod_authz_host.so #LoadModule authz_owner_module modules/mod_authz_owner.so LoadModule authz_user_module modules/mod_authz_user.so LoadModule autoindex_module modules/mod_autoindex.so #LoadModule cache_module modules/mod_cache.so #LoadModule cern_meta_module modules/mod_cern_meta.so LoadModule cgi_module modules/mod_cgi.so #LoadModule charset_lite_module modules/mod_charset_lite.so #LoadModule dav_module modules/mod_dav.so #LoadModule dav_fs_module modules/mod_dav_fs.so #LoadModule dav_lock_module modules/mod_dav_lock.so #LoadModule dbd_module modules/mod_dbd.so #LoadModule deflate_module modules/mod_deflate.so LoadModule dir_module modules/mod_dir.so #LoadModule disk_cache_module modules/mod_disk_cache.so #LoadModule dumpio_module modules/mod_dumpio.so LoadModule env_module modules/mod_env.so #LoadModule expires_module modules/mod_expires.so #LoadModule ext_filter_module modules/mod_ext_filter.so #LoadModule file_cache_module modules/mod_file_cache.so #LoadModule filter_module modules/mod_filter.so #LoadModule headers_module modules/mod_headers.so #LoadModule ident_module modules/mod_ident.so #LoadModule imagemap_module modules/mod_imagemap.so LoadModule include_module modules/mod_include.so LoadModule info_module modules/mod_info.so LoadModule isapi_module modules/mod_isapi.so #LoadModule ldap_module modules/mod_ldap.so #LoadModule logio_module modules/mod_logio.so LoadModule log_config_module modules/mod_log_config.so #LoadModule log_forensic_module modules/mod_log_forensic.so #LoadModule mem_cache_module modules/mod_mem_cache.so LoadModule mime_module modules/mod_mime.so #LoadModule mime_magic_module modules/mod_mime_magic.so LoadModule negotiation_module modules/mod_negotiation.so #LoadModule proxy_module modules/mod_proxy.so #LoadModule proxy_ajp_module modules/mod_proxy_ajp.so #LoadModule proxy_balancer_module modules/mod_proxy_balancer.so #LoadModule proxy_connect_module modules/mod_proxy_connect.so #LoadModule proxy_ftp_module modules/mod_proxy_ftp.so #LoadModule proxy_http_module modules/mod_proxy_http.so #LoadModule reqtimeout_module modules/mod_reqtimeout.so #LoadModule rewrite_module modules/mod_rewrite.so LoadModule setenvif_module modules/mod_setenvif.so #LoadModule speling_module modules/mod_speling.so #LoadModule ssl_module modules/mod_ssl.so LoadModule status_module modules/mod_status.so #LoadModule substitute_module modules/mod_substitute.so #LoadModule unique_id_module modules/mod_unique_id.so #LoadModule userdir_module modules/mod_userdir.so #LoadModule usertrack_module modules/mod_usertrack.so #LoadModule version_module modules/mod_version.so #LoadModule vhost_alias_module modules/mod_vhost_alias.so #LoadModule php5_module "c:/php/php5apache2_2.dll" <IfModule !mpm_netware_module> <IfModule !mpm_winnt_module> # # If you wish httpd to run as a different user or group, you must run # httpd as root initially and it will switch. # # User/Group: The name (or #number) of the user/group to run httpd as. # It is usually good practice to create a dedicated user and group for # running httpd, as with most system services. # User daemon Group daemon </IfModule> </IfModule> # 'Main' server configuration # # The directives in this section set up the values used by the 'main' # server, which responds to any requests that aren't handled by a # <VirtualHost> definition. These values also provide defaults for # any <VirtualHost> containers you may define later in the file. # # All of these directives may appear inside <VirtualHost> containers, # in which case these default settings will be overridden for the # virtual host being defined. # # # ServerAdmin: Your address, where problems with the server should be # e-mailed. This address appears on some server-generated pages, such # as error documents. e.g. [email protected] # ServerAdmin [email protected] # # ServerName gives the name and port that the server uses to identify itself. # This can often be determined automatically, but we recommend you specify # it explicitly to prevent problems during startup. # # If your host doesn't have a registered DNS name, enter its IP address here. # #ServerName :80 # # DocumentRoot: The directory out of which you will serve your # documents. By default, all requests are taken from this directory, but # symbolic links and aliases may be used to point to other locations. # DocumentRoot "C:/Program Files (x86)/Apache Software Foundation/Apache2.2/htdocs" # # Each directory to which Apache has access can be configured with respect # to which services and features are allowed and/or disabled in that # directory (and its subdirectories). # # First, we configure the "default" to be a very restrictive set of # features. # <Directory /> Options FollowSymLinks AllowOverride None Order deny,allow Allow from all </Directory> # # Note that from this point forward you must specifically allow # particular features to be enabled - so if something's not working as # you might expect, make sure that you have specifically enabled it # below. # # # This should be changed to whatever you set DocumentRoot to. # <Directory "C:/Program Files (x86)/Apache Software Foundation/Apache2.2/htdocs"> # # Possible values for the Options directive are "None", "All", # or any combination of: # Indexes Includes FollowSymLinks SymLinksifOwnerMatch ExecCGI MultiViews # # Note that "MultiViews" must be named *explicitly* --- "Options All" # doesn't give it to you. # # The Options directive is both complicated and important. Please see # http://httpd.apache.org/docs/2.2/mod/core.html#options # for more information. # Options Indexes FollowSymLinks # # AllowOverride controls what directives may be placed in .htaccess files. # It can be "All", "None", or any combination of the keywords: # Options FileInfo AuthConfig Limit # AllowOverride All # # Controls who can get stuff from this server. # Order deny,allow Allow from all </Directory> # # DirectoryIndex: sets the file that Apache will serve if a directory # is requested. # <IfModule dir_module> DirectoryIndex index.html index.php index.phtml index.htm default.html default.php default.phtml default.htm </IfModule> # # The following lines prevent .htaccess and .htpasswd files from being # viewed by Web clients. # <FilesMatch "^\.ht"> Order allow,deny Deny from all Satisfy All </FilesMatch> # # ErrorLog: The location of the error log file. # If you do not specify an ErrorLog directive within a <VirtualHost> # container, error messages relating to that virtual host will be # logged here. If you *do* define an error logfile for a <VirtualHost> # container, that host's errors will be logged there and not here. # ErrorLog "logs/error.log" # # LogLevel: Control the number of messages logged to the error_log. # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. # LogLevel warn <IfModule log_config_module> # # The following directives define some format nicknames for use with # a CustomLog directive (see below). # LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common <IfModule logio_module> # You need to enable mod_logio.c to use %I and %O LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio </IfModule> # # The location and format of the access logfile (Common Logfile Format). # If you do not define any access logfiles within a <VirtualHost> # container, they will be logged here. Contrariwise, if you *do* # define per-<VirtualHost> access logfiles, transactions will be # logged therein and *not* in this file. # CustomLog "logs/access.log" common # # If you prefer a logfile with access, agent, and referer information # (Combined Logfile Format) you can use the following directive. # #CustomLog "logs/access.log" combined </IfModule> <IfModule alias_module> # # Redirect: Allows you to tell clients about documents that used to # exist in your server's namespace, but do not anymore. The client # will make a new request for the document at its new location. # Example: # Redirect permanent /foo http:///bar # # Alias: Maps web paths into filesystem paths and is used to # access content that does not live under the DocumentRoot. # Example: # Alias /webpath /full/filesystem/path # # If you include a trailing / on /webpath then the server will # require it to be present in the URL. You will also likely # need to provide a <Directory> section to allow access to # the filesystem path. # # ScriptAlias: This controls which directories contain server scripts. # ScriptAliases are essentially the same as Aliases, except that # documents in the target directory are treated as applications and # run by the server when requested rather than as documents sent to the # client. The same rules about trailing "/" apply to ScriptAlias # directives as to Alias. # ScriptAlias /cgi-bin/ "C:/Program Files (x86)/Apache Software Foundation/Apache2.2/cgi-bin/" </IfModule> <IfModule cgid_module> # # ScriptSock: On threaded servers, designate the path to the UNIX # socket used to communicate with the CGI daemon of mod_cgid. # #Scriptsock logs/cgisock </IfModule> # # "C:/Program Files (x86)/Apache Software Foundation/Apache2.2/cgi-bin" should be changed to whatever your ScriptAliased # CGI directory exists, if you have that configured. # <Directory "C:/Program Files (x86)/Apache Software Foundation/Apache2.2/cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> # # DefaultType: the default MIME type the server will use for a document # if it cannot otherwise determine one, such as from filename extensions. # If your server contains mostly text or HTML documents, "text/plain" is # a good value. If most of your content is binary, such as applications # or images, you may want to use "application/octet-stream" instead to # keep browsers from trying to display binary files as though they are # text. # DefaultType text/plain <IfModule mime_module> # # TypesConfig points to the file containing the list of mappings from # filename extension to MIME-type. # TypesConfig conf/mime.types # # AddType allows you to add to or override the MIME configuration # file specified in TypesConfig for specific file types. # #AddType application/x-gzip .tgz # # AddEncoding allows you to have certain browsers uncompress # information on the fly. Note: Not all browsers support this. # #AddEncoding x-compress .Z #AddEncoding x-gzip .gz .tgz # # If the AddEncoding directives above are commented-out, then you # probably should define those extensions to indicate media types: # AddType application/x-compress .Z AddType application/x-gzip .gz .tgz # # AddHandler allows you to map certain file extensions to "handlers": # actions unrelated to filetype. These can be either built into the server # or added with the Action directive (see below) # # To use CGI scripts outside of ScriptAliased directories: # (You will also need to add "ExecCGI" to the "Options" directive.) # #AddHandler cgi-script .cgi # For type maps (negotiated resources): #AddHandler type-map var # # Filters allow you to process content before it is sent to the client. # # To parse .shtml files for server-side includes (SSI): # (You will also need to add "Includes" to the "Options" directive.) # #AddType text/html .shtml #AddOutputFilter INCLUDES .shtml AddType application/x-httpd-php .php AddType application/x-httpd-php .phtml </IfModule> # # The mod_mime_magic module allows the server to use various hints from the # contents of the file itself to determine its type. The MIMEMagicFile # directive tells the module where the hint definitions are located. # #MIMEMagicFile conf/magic # # Customizable error responses come in three flavors: # 1) plain text 2) local redirects 3) external redirects # # Some examples: #ErrorDocument 500 "The server made a boo boo." #ErrorDocument 404 /missing.html #ErrorDocument 404 "/cgi-bin/missing_handler.pl" #ErrorDocument 402 http:///subscription_info.html # # # EnableMMAP and EnableSendfile: On systems that support it, # memory-mapping or the sendfile syscall is used to deliver # files. This usually improves server performance, but must # be turned off when serving from networked-mounted # filesystems or if support for these functions is otherwise # broken on your system. # #EnableMMAP off #EnableSendfile off # Supplemental configuration # # The configuration files in the conf/extra/ directory can be # included to add extra features or to modify the default configuration of # the server, or you may simply copy their contents here and change as # necessary. # Server-pool management (MPM specific) #Include conf/extra/httpd-mpm.conf # Multi-language error messages #Include conf/extra/httpd-multilang-errordoc.conf # Fancy directory listings #Include conf/extra/httpd-autoindex.conf # Language settings #Include conf/extra/httpd-languages.conf # User home directories #Include conf/extra/httpd-userdir.conf # Real-time info on requests and configuration #Include conf/extra/httpd-info.conf # Virtual hosts #Include conf/extra/httpd-vhosts.conf # Local access to the Apache HTTP Server Manual #Include conf/extra/httpd-manual.conf # Distributed authoring and versioning (WebDAV) #Include conf/extra/httpd-dav.conf # Various default settings #Include conf/extra/httpd-default.conf # Secure (SSL/TLS) connections #Include conf/extra/httpd-ssl.conf # # Note: The following must must be present to support # starting without SSL on platforms with no /dev/random equivalent # but a statically compiled-in mod_ssl. # <IfModule ssl_module> SSLRandomSeed startup builtin SSLRandomSeed connect builtin </IfModule> #PHPIniDir "c:/php" #BEGIN PHP INSTALLER EDITS - REMOVE ONLY ON UNINSTALL PHPIniDir "C:/PHP/" LoadModule php5_module "C:/PHP/php5apache2_2.dll" #END PHP INSTALLER EDITS - REMOVE ONLY ON UNINSTALL P.S sorry for the shortness of this post. I am in a rush

  Read the article

• Apache won't accept external requests

  - by Eric

  I am running Apache 2.2 on windows and I would like to access it remotely. Currently I can only access it from my local machine. I know the problem is not port forwarding because I tested it with other web servers (written in python). My httpd.conf file is below. I installed apache with the PHP installer. # # This is the main Apache HTTP server configuration file. It contains the # configuration directives that give the server its instructions. # See <URL:http://httpd.apache.org/docs/2.2> for detailed information. # In particular, see # <URL:http://httpd.apache.org/docs/2.2/mod/directives.html> # for a discussion of each configuration directive. # # Do NOT simply read the instructions in here without understanding # what they do. They're here only as hints or reminders. If you are unsure # consult the online docs. You have been warned. # # Configuration and logfile names: If the filenames you specify for many # of the server's control files begin with "/" (or "drive:/" for Win32), the # server will use that explicit path. If the filenames do *not* begin # with "/", the value of ServerRoot is prepended -- so "logs/foo.log" # with ServerRoot set to "C:/Program Files (x86)/Apache Software Foundation/Apache2.2" will be interpreted by the # server as "C:/Program Files (x86)/Apache Software Foundation/Apache2.2/logs/foo.log". # # NOTE: Where filenames are specified, you must use forward slashes # instead of backslashes (e.g., "c:/apache" instead of "c:\apache"). # If a drive letter is omitted, the drive on which httpd.exe is located # will be used by default. It is recommended that you always supply # an explicit drive letter in absolute paths to avoid confusion. # # ServerRoot: The top of the directory tree under which the server's # configuration, error, and log files are kept. # # Do not add a slash at the end of the directory path. If you point # ServerRoot at a non-local disk, be sure to point the LockFile directive # at a local disk. If you wish to share the same ServerRoot for multiple # httpd daemons, you will need to change at least LockFile and PidFile. # ServerRoot "C:/Program Files (x86)/Apache Software Foundation/Apache2.2" # # Listen: Allows you to bind Apache to specific IP addresses and/or # ports, instead of the default. See also the <VirtualHost> # directive. # # Change this to Listen on specific IP addresses as shown below to # prevent Apache from glomming onto all bound IP addresses. # #Listen 12.34.56.78:80 Listen 80 # # Dynamic Shared Object (DSO) Support # # To be able to use the functionality of a module which was built as a DSO you # have to place corresponding `LoadModule' lines at this location so the # directives contained in it are actually available _before_ they are used. # Statically compiled modules (those listed by `httpd -l') do not need # to be loaded here. # # Example: # LoadModule foo_module modules/mod_foo.so # LoadModule actions_module modules/mod_actions.so LoadModule alias_module modules/mod_alias.so LoadModule asis_module modules/mod_asis.so LoadModule auth_basic_module modules/mod_auth_basic.so #LoadModule auth_digest_module modules/mod_auth_digest.so #LoadModule authn_alias_module modules/mod_authn_alias.so #LoadModule authn_anon_module modules/mod_authn_anon.so #LoadModule authn_dbd_module modules/mod_authn_dbd.so #LoadModule authn_dbm_module modules/mod_authn_dbm.so LoadModule authn_default_module modules/mod_authn_default.so LoadModule authn_file_module modules/mod_authn_file.so #LoadModule authnz_ldap_module modules/mod_authnz_ldap.so #LoadModule authz_dbm_module modules/mod_authz_dbm.so LoadModule authz_default_module modules/mod_authz_default.so LoadModule authz_groupfile_module modules/mod_authz_groupfile.so LoadModule authz_host_module modules/mod_authz_host.so #LoadModule authz_owner_module modules/mod_authz_owner.so LoadModule authz_user_module modules/mod_authz_user.so LoadModule autoindex_module modules/mod_autoindex.so #LoadModule cache_module modules/mod_cache.so #LoadModule cern_meta_module modules/mod_cern_meta.so LoadModule cgi_module modules/mod_cgi.so #LoadModule charset_lite_module modules/mod_charset_lite.so #LoadModule dav_module modules/mod_dav.so #LoadModule dav_fs_module modules/mod_dav_fs.so #LoadModule dav_lock_module modules/mod_dav_lock.so #LoadModule dbd_module modules/mod_dbd.so #LoadModule deflate_module modules/mod_deflate.so LoadModule dir_module modules/mod_dir.so #LoadModule disk_cache_module modules/mod_disk_cache.so #LoadModule dumpio_module modules/mod_dumpio.so LoadModule env_module modules/mod_env.so #LoadModule expires_module modules/mod_expires.so #LoadModule ext_filter_module modules/mod_ext_filter.so #LoadModule file_cache_module modules/mod_file_cache.so #LoadModule filter_module modules/mod_filter.so #LoadModule headers_module modules/mod_headers.so #LoadModule ident_module modules/mod_ident.so #LoadModule imagemap_module modules/mod_imagemap.so LoadModule include_module modules/mod_include.so LoadModule info_module modules/mod_info.so LoadModule isapi_module modules/mod_isapi.so #LoadModule ldap_module modules/mod_ldap.so #LoadModule logio_module modules/mod_logio.so LoadModule log_config_module modules/mod_log_config.so #LoadModule log_forensic_module modules/mod_log_forensic.so #LoadModule mem_cache_module modules/mod_mem_cache.so LoadModule mime_module modules/mod_mime.so #LoadModule mime_magic_module modules/mod_mime_magic.so LoadModule negotiation_module modules/mod_negotiation.so #LoadModule proxy_module modules/mod_proxy.so #LoadModule proxy_ajp_module modules/mod_proxy_ajp.so #LoadModule proxy_balancer_module modules/mod_proxy_balancer.so #LoadModule proxy_connect_module modules/mod_proxy_connect.so #LoadModule proxy_ftp_module modules/mod_proxy_ftp.so #LoadModule proxy_http_module modules/mod_proxy_http.so #LoadModule reqtimeout_module modules/mod_reqtimeout.so #LoadModule rewrite_module modules/mod_rewrite.so LoadModule setenvif_module modules/mod_setenvif.so #LoadModule speling_module modules/mod_speling.so #LoadModule ssl_module modules/mod_ssl.so LoadModule status_module modules/mod_status.so #LoadModule substitute_module modules/mod_substitute.so #LoadModule unique_id_module modules/mod_unique_id.so #LoadModule userdir_module modules/mod_userdir.so #LoadModule usertrack_module modules/mod_usertrack.so #LoadModule version_module modules/mod_version.so #LoadModule vhost_alias_module modules/mod_vhost_alias.so #LoadModule php5_module "c:/php/php5apache2_2.dll" <IfModule !mpm_netware_module> <IfModule !mpm_winnt_module> # # If you wish httpd to run as a different user or group, you must run # httpd as root initially and it will switch. # # User/Group: The name (or #number) of the user/group to run httpd as. # It is usually good practice to create a dedicated user and group for # running httpd, as with most system services. # User daemon Group daemon </IfModule> </IfModule> # 'Main' server configuration # # The directives in this section set up the values used by the 'main' # server, which responds to any requests that aren't handled by a # <VirtualHost> definition. These values also provide defaults for # any <VirtualHost> containers you may define later in the file. # # All of these directives may appear inside <VirtualHost> containers, # in which case these default settings will be overridden for the # virtual host being defined. # # # ServerAdmin: Your address, where problems with the server should be # e-mailed. This address appears on some server-generated pages, such # as error documents. e.g. [email protected] # ServerAdmin [email protected] # # ServerName gives the name and port that the server uses to identify itself. # This can often be determined automatically, but we recommend you specify # it explicitly to prevent problems during startup. # # If your host doesn't have a registered DNS name, enter its IP address here. # #ServerName :80 # # DocumentRoot: The directory out of which you will serve your # documents. By default, all requests are taken from this directory, but # symbolic links and aliases may be used to point to other locations. # DocumentRoot "C:/Program Files (x86)/Apache Software Foundation/Apache2.2/htdocs" # # Each directory to which Apache has access can be configured with respect # to which services and features are allowed and/or disabled in that # directory (and its subdirectories). # # First, we configure the "default" to be a very restrictive set of # features. # <Directory /> Options FollowSymLinks AllowOverride None Order deny,allow Allow from all </Directory> # # Note that from this point forward you must specifically allow # particular features to be enabled - so if something's not working as # you might expect, make sure that you have specifically enabled it # below. # # # This should be changed to whatever you set DocumentRoot to. # <Directory "C:/Program Files (x86)/Apache Software Foundation/Apache2.2/htdocs"> # # Possible values for the Options directive are "None", "All", # or any combination of: # Indexes Includes FollowSymLinks SymLinksifOwnerMatch ExecCGI MultiViews # # Note that "MultiViews" must be named *explicitly* --- "Options All" # doesn't give it to you. # # The Options directive is both complicated and important. Please see # http://httpd.apache.org/docs/2.2/mod/core.html#options # for more information. # Options Indexes FollowSymLinks # # AllowOverride controls what directives may be placed in .htaccess files. # It can be "All", "None", or any combination of the keywords: # Options FileInfo AuthConfig Limit # AllowOverride All # # Controls who can get stuff from this server. # Order deny,allow Allow from all </Directory> # # DirectoryIndex: sets the file that Apache will serve if a directory # is requested. # <IfModule dir_module> DirectoryIndex index.html index.php index.phtml index.htm default.html default.php default.phtml default.htm </IfModule> # # The following lines prevent .htaccess and .htpasswd files from being # viewed by Web clients. # <FilesMatch "^\.ht"> Order allow,deny Deny from all Satisfy All </FilesMatch> # # ErrorLog: The location of the error log file. # If you do not specify an ErrorLog directive within a <VirtualHost> # container, error messages relating to that virtual host will be # logged here. If you *do* define an error logfile for a <VirtualHost> # container, that host's errors will be logged there and not here. # ErrorLog "logs/error.log" # # LogLevel: Control the number of messages logged to the error_log. # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. # LogLevel warn <IfModule log_config_module> # # The following directives define some format nicknames for use with # a CustomLog directive (see below). # LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common <IfModule logio_module> # You need to enable mod_logio.c to use %I and %O LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio </IfModule> # # The location and format of the access logfile (Common Logfile Format). # If you do not define any access logfiles within a <VirtualHost> # container, they will be logged here. Contrariwise, if you *do* # define per-<VirtualHost> access logfiles, transactions will be # logged therein and *not* in this file. # CustomLog "logs/access.log" common # # If you prefer a logfile with access, agent, and referer information # (Combined Logfile Format) you can use the following directive. # #CustomLog "logs/access.log" combined </IfModule> <IfModule alias_module> # # Redirect: Allows you to tell clients about documents that used to # exist in your server's namespace, but do not anymore. The client # will make a new request for the document at its new location. # Example: # Redirect permanent /foo http:///bar # # Alias: Maps web paths into filesystem paths and is used to # access content that does not live under the DocumentRoot. # Example: # Alias /webpath /full/filesystem/path # # If you include a trailing / on /webpath then the server will # require it to be present in the URL. You will also likely # need to provide a <Directory> section to allow access to # the filesystem path. # # ScriptAlias: This controls which directories contain server scripts. # ScriptAliases are essentially the same as Aliases, except that # documents in the target directory are treated as applications and # run by the server when requested rather than as documents sent to the # client. The same rules about trailing "/" apply to ScriptAlias # directives as to Alias. # ScriptAlias /cgi-bin/ "C:/Program Files (x86)/Apache Software Foundation/Apache2.2/cgi-bin/" </IfModule> <IfModule cgid_module> # # ScriptSock: On threaded servers, designate the path to the UNIX # socket used to communicate with the CGI daemon of mod_cgid. # #Scriptsock logs/cgisock </IfModule> # # "C:/Program Files (x86)/Apache Software Foundation/Apache2.2/cgi-bin" should be changed to whatever your ScriptAliased # CGI directory exists, if you have that configured. # <Directory "C:/Program Files (x86)/Apache Software Foundation/Apache2.2/cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> # # DefaultType: the default MIME type the server will use for a document # if it cannot otherwise determine one, such as from filename extensions. # If your server contains mostly text or HTML documents, "text/plain" is # a good value. If most of your content is binary, such as applications # or images, you may want to use "application/octet-stream" instead to # keep browsers from trying to display binary files as though they are # text. # DefaultType text/plain <IfModule mime_module> # # TypesConfig points to the file containing the list of mappings from # filename extension to MIME-type. # TypesConfig conf/mime.types # # AddType allows you to add to or override the MIME configuration # file specified in TypesConfig for specific file types. # #AddType application/x-gzip .tgz # # AddEncoding allows you to have certain browsers uncompress # information on the fly. Note: Not all browsers support this. # #AddEncoding x-compress .Z #AddEncoding x-gzip .gz .tgz # # If the AddEncoding directives above are commented-out, then you # probably should define those extensions to indicate media types: # AddType application/x-compress .Z AddType application/x-gzip .gz .tgz # # AddHandler allows you to map certain file extensions to "handlers": # actions unrelated to filetype. These can be either built into the server # or added with the Action directive (see below) # # To use CGI scripts outside of ScriptAliased directories: # (You will also need to add "ExecCGI" to the "Options" directive.) # #AddHandler cgi-script .cgi # For type maps (negotiated resources): #AddHandler type-map var # # Filters allow you to process content before it is sent to the client. # # To parse .shtml files for server-side includes (SSI): # (You will also need to add "Includes" to the "Options" directive.) # #AddType text/html .shtml #AddOutputFilter INCLUDES .shtml AddType application/x-httpd-php .php AddType application/x-httpd-php .phtml </IfModule> # # The mod_mime_magic module allows the server to use various hints from the # contents of the file itself to determine its type. The MIMEMagicFile # directive tells the module where the hint definitions are located. # #MIMEMagicFile conf/magic # # Customizable error responses come in three flavors: # 1) plain text 2) local redirects 3) external redirects # # Some examples: #ErrorDocument 500 "The server made a boo boo." #ErrorDocument 404 /missing.html #ErrorDocument 404 "/cgi-bin/missing_handler.pl" #ErrorDocument 402 http:///subscription_info.html # # # EnableMMAP and EnableSendfile: On systems that support it, # memory-mapping or the sendfile syscall is used to deliver # files. This usually improves server performance, but must # be turned off when serving from networked-mounted # filesystems or if support for these functions is otherwise # broken on your system. # #EnableMMAP off #EnableSendfile off # Supplemental configuration # # The configuration files in the conf/extra/ directory can be # included to add extra features or to modify the default configuration of # the server, or you may simply copy their contents here and change as # necessary. # Server-pool management (MPM specific) #Include conf/extra/httpd-mpm.conf # Multi-language error messages #Include conf/extra/httpd-multilang-errordoc.conf # Fancy directory listings #Include conf/extra/httpd-autoindex.conf # Language settings #Include conf/extra/httpd-languages.conf # User home directories #Include conf/extra/httpd-userdir.conf # Real-time info on requests and configuration #Include conf/extra/httpd-info.conf # Virtual hosts #Include conf/extra/httpd-vhosts.conf # Local access to the Apache HTTP Server Manual #Include conf/extra/httpd-manual.conf # Distributed authoring and versioning (WebDAV) #Include conf/extra/httpd-dav.conf # Various default settings #Include conf/extra/httpd-default.conf # Secure (SSL/TLS) connections #Include conf/extra/httpd-ssl.conf # # Note: The following must must be present to support # starting without SSL on platforms with no /dev/random equivalent # but a statically compiled-in mod_ssl. # <IfModule ssl_module> SSLRandomSeed startup builtin SSLRandomSeed connect builtin </IfModule> #PHPIniDir "c:/php" #BEGIN PHP INSTALLER EDITS - REMOVE ONLY ON UNINSTALL PHPIniDir "C:/PHP/" LoadModule php5_module "C:/PHP/php5apache2_2.dll" #END PHP INSTALLER EDITS - REMOVE ONLY ON UNINSTALL P.S sorry for the shortness of this post. I am in a rush

  Read the article

• Weird WLAN connection

  - by tuelsch

  I assembled my first computer on my own. As I realised it had no WLAN (AsRock Z77 Extreme 4m) I bought a WLAN stick (ZyXel NWD 2105), plugged it in, started the setup from the CD and it worked, until I restarted the PC. That's when the problems started. The stick is able to connect to the router (P-660HN-F1Z) and the connection is stable, but not the internet access. In estimately 1 minute intervals there might be a short connection timeframe and dropbox or windows update are able to download some data, but as soon as I try to open a website the internet access is away. Note that the connection to the router does not shut down and remains stable at around 80-90%. The problem is definetly located on my pc, because with my laptop and phone the connection is stable and fast. Because I was so pissed off, I bought a EW-7612PIn V2 (PCI-E WLAN adapter), same problem. Now the weird thing is, if I don't use the PC for about 2 days, start it up, there is internet access (happened with both the stick and the PCI-E card). A bit slow, but it does not get away just like that, until I shut it down. Then, no matter how many times I restart, it won't come back. I googled a lot but now I'm at the end with my latin. Has anyone had a similar problem and resolved it? Technical details: Motherboard: AsRock Z77 Extreme 4M OS: Windows 7 professional 64bit Stick: Zyxel wireless N adapter NWD2105 PCI-E card: Edimax EW-7612PIn V2 Router: ZyXel P-660HN-F1Z Windows-IP-Konfiguration Hostname . . . . . . . . . . . . : xyz Primäres DNS-Suffix . . . . . . . : Knotentyp . . . . . . . . . . . . : Hybrid IP-Routing aktiviert . . . . . . : Nein WINS-Proxy aktiviert . . . . . . : Nein Drahtlos-LAN-Adapter Drahtlosnetzwerkverbindung 5: Medienstatus. . . . . . . . . . . : Medium getrennt Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Microsoft Virtual WiFi Miniport Adapter # 3 Physikalische Adresse . . . . . . : 80-1F-02-61-C0-A6 DHCP aktiviert. . . . . . . . . . : Ja Autokonfiguration aktiviert . . . : Ja Drahtlos-LAN-Adapter Drahtlosnetzwerkverbindung 4: Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Edimax 802.11n Wireless Adapter Physikalische Adresse . . . . . . : 80-1F-02-61-C0-A6 DHCP aktiviert. . . . . . . . . . : Ja Autokonfiguration aktiviert . . . : Ja Verbindungslokale IPv6-Adresse . : fe80::38d2:f489:726d:1fb5%17(Bevorzugt) IPv4-Adresse . . . . . . . . . . : 192.168.1.41(Bevorzugt) Subnetzmaske . . . . . . . . . . : 255.255.255.0 Lease erhalten. . . . . . . . . . : Donnerstag, 15. November 2012 10:51:05 Lease läuft ab. . . . . . . . . . : Sonntag, 18. November 2012 10:51:18 Standardgateway . . . . . . . . . : 192.168.1.1 DHCP-Server . . . . . . . . . . . : 192.168.1.1 DHCPv6-IAID . . . . . . . . . . . : 578821890 DHCPv6-Client-DUID. . . . . . . . : 00-01-00-01-17-FF-D5-FE-BC-5F-F4-48-FC-4B DNS-Server . . . . . . . . . . . : 91.233.182.2 194.230.1.39 NetBIOS über TCP/IP . . . . . . . : Aktiviert Tunneladapter isatap.{263BEB98-344B-435C-888F-1B15B97C3AC1}: Medienstatus. . . . . . . . . . . : Medium getrennt Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Microsoft-ISATAP-Adapter Physikalische Adresse . . . . . . : 00-00-00-00-00-00-00-E0 DHCP aktiviert. . . . . . . . . . : Nein Autokonfiguration aktiviert . . . : Ja Tunneladapter Teredo Tunneling Pseudo-Interface: Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physikalische Adresse . . . . . . : 00-00-00-00-00-00-00-E0 DHCP aktiviert. . . . . . . . . . : Nein Autokonfiguration aktiviert . . . : Ja IPv6-Adresse. . . . . . . . . . . : 2001:0:9d38:6ab8:209c:2944:3f57:fed6(Bevo rzugt) Verbindungslokale IPv6-Adresse . : fe80::209c:2944:3f57:fed6%11(Bevorzugt) Standardgateway . . . . . . . . . : :: NetBIOS über TCP/IP . . . . . . . : Deaktiviert C:\Users\xyz>ping 192.168.1.1 Ping wird ausgeführt für 192.168.1.1 mit 32 Bytes Daten: Antwort von 192.168.1.1: Bytes=32 Zeit=2ms TTL=254 Antwort von 192.168.1.1: Bytes=32 Zeit=2ms TTL=254 Antwort von 192.168.1.1: Bytes=32 Zeit=2ms TTL=254 Antwort von 192.168.1.1: Bytes=32 Zeit=2ms TTL=254 Ping-Statistik für 192.168.1.1: Pakete: Gesendet = 4, Empfangen = 4, Verloren = 0 (0% Verlust), Ca. Zeitangaben in Millisek.: Minimum = 2ms, Maximum = 2ms, Mittelwert = 2ms

  Read the article

• Having an issue with overwriting an element of a file correctly (numeric)

  - by IngeniousHax

  This is an ATM style program, but currently it doesn't do exactly what I need it to do... I need to get the current balance, and when money is transferred from either checking or savings, it should add it to checking and subtract it from savings. which is does, but not correctly... Input example -=[ Funds Transfer ]=- -=[ Savings to Checking ]=- Account Name: nomadic Amount to transfer: $400 New Balance in Checking: $900 // original was 500 New Balance in Savings: $7.7068e+012 // this should now be 1100... Here is my code, it's a lot of code, but there are no errors, so throwing it into an IDE and compiling should be fairly quick for whoever would like to help. mainBankClass.h mainBankClass.h #ifndef MAINBANKCLASS_H #define MAINBANKCLASS_H #include <iostream> #include <fstream> #include <string> using namespace std; class Banking { protected: string checkAcctName, saveAcctName; // Name on the account int acctNumber[13]; // Account number float acctBalance, initSaveDeposit, initCheckDeposit, depAmt; // amount in account, and amount to deposit public: char getBalanceChoice(); // Get name on account for displaying relevant information char newAccountMenu(); // Create a new account and assign it a random account number void invalid(char *); // If an invalid option is chosen char menu(); // Print the main menu for the user. virtual float deposit(){ return 0; } // virtual function for deposits // virtual float withdrawal() = 0; // Virtual function for withdrawals void fatal(char *); // Handles fatal errors. Banking(); }; class Checking : public Banking { public: friend ostream operator<<(ostream &, Checking &); friend istream operator>>(istream &, Checking &); Checking operator <= (const Checking &) const; void newCheckingAccount(); void viewCheckingBalance(); void transferFromSaving(); float deposit() { return (acctBalance += depAmt); } }; class Saving : public Banking { public: friend ostream &operator<<(ostream &, Saving &); friend istream &operator>>(istream &, Saving &); Saving operator <= (const Saving &) const; void newSavingAccount(); void viewSavingBalance(); void transferFromChecking(); float deposit() { return (acctBalance += depAmt); } }; class checkAndSave : public Banking { public: void newCheckAndSave(); void viewBothBalances(); }; #endif bankAccount.cpp #include <iostream> #include <sstream> #include <string> #include <iomanip> #include <fstream> #include <time.h> #include "MainBankClass.h" /*****************************\ | BANKING CONSTRUCTOR | \*****************************/ Banking::Banking() { string acctName; // Name on the account acctNumber[13] = 0; // Account number acctBalance = 0; initCheckDeposit = 0; initSaveDeposit = 0; depAmt = 0; }; /********************************\ | The following code is to print the menu | | and recieve the users choice on what | | they want to do with the ATM | \********************************/ char Banking::menu() { char choice; system("cls"); cout << "\t\t -=[ Main Menu ]=- \n\n" << "\tA) Create New Account\n" << "\tB) View Account Balance\n" << "\tC) Transfer Funds From Checking To Savings\n" << "\tD) Transfer Funds From Savings To Checking\n" << "\tE) Exit\n" << "\n\n\tSelection: "; cin >> choice; cin.ignore(); choice = toupper(choice); while(!isalpha(choice)) { invalid("[!!] Invalid selection.\n[!!] Choose a valid option: "); cin >> choice; cin.ignore(); } return choice; } /*********************\ | Will read in account choic | | and display it for the user | \*********************/ char Banking::getBalanceChoice() { char choice; fstream saveFile("saving.dat", ios::in | ios::beg); system("cls"); cout << "\t\t -=[ View Account Balance ]=-\n\n"; cout << "A) View Checking Account\n" << "B) View Saving Account\n" << "C) View Checking \\ Saving Account\n" << endl; cout << "Choice: "; cin >> choice; choice = toupper(choice); if(!isalpha(choice)) fatal(" [!!] Invalid Choice"); return choice; } /***************************\ | Incase an invalid decision to made | | this throws the error message sent | | to it by the calling area | \***************************/ void Banking::invalid(char *msg) { cout << msg; } /*************************\ | Used if files can not be opened | | and exits with code 251: | | miscommunication with server | \*************************/ void Banking::fatal(char *msg) { cout << msg; exit(1); } /***************************\ | Create an account, either checking | | or savings, or both. | | Must should create a randomly | | generated account number that will | | correspond with each account. | \***************************/ /************************\ NOTE:: WILL BE UPDATED TO CONTAIN A PIN FOR ACCOUNT VERIFICATION *************************/ char Banking::newAccountMenu() { srand(time(NULL)); // Seed random generator with time initialized to NULL char acctChoice; // choice for the account type ofstream checkFile("checking.dat", ios::out | ios::app); // For saving checking accounts ofstream saveFile("saving.dat", ios::out | ios::app); // For saving savings accounts system("cls"); cout << "\t\t-=[ New Account Creation ]=-\n\n" << endl; cout << "A) Checking Account\n" << "B) Savings Account\n" << "C) Checking and Saving Account\n" << endl; cout << "New account type: "; cin >> acctChoice; acctChoice = toupper(acctChoice); cin.clear(); cin.sync(); return acctChoice; } /********************************************************************* ********************************************************************** CHECKING ACCOUNT CODE ********************************************************************** **********************************************************************/ // New Checking Account Creation void Checking::newCheckingAccount() { system("cls"); ofstream checkFile("checking.dat", ios::out | ios::app); // For saving checking accounts cout << "\t\t -=[ New Checking Account ]=- \n" << endl; cout << "Name of the main holder to be on the account: "; getline(cin, checkAcctName); cout << "Initial deposit amount: $"; cin >> initCheckDeposit; if(initCheckDeposit <= 0) { while(initCheckDeposit <= 0) { invalid("[!!] 0 or negative amount entered\nMaybe a typo?\n"); cout << "Deposit Amount: $"; cin >> initCheckDeposit; } } if(!checkFile) fatal("[!!] Fatal Error 251: Miscommunication with server\n"); checkFile << checkAcctName << endl; for(int j = 0; j < 13; j++) { acctNumber[j] = (rand() % 10); // Build a random checking account number checkFile << acctNumber[j]; } checkFile << endl; checkFile << initCheckDeposit << endl; checkFile.close(); } void Checking::viewCheckingBalance() { fstream checkFile("checking.dat", ios::in | ios::beg); string name; int i = 0; double balance = 0; system("cls"); cout << "\t\t -=[ View Checking Account ]=-\n\n" << endl; cout << "Account Name: "; cin.sync(); getline(cin, name); getline(checkFile, checkAcctName); while(name != checkAcctName && !checkFile.fail()) { i++; getline(checkFile, checkAcctName); } if(name == checkAcctName) { system("cls"); cout << "\t\t -=[ Checking Account Balance ]=-\n\n" << endl; cout << "Account Name: " << checkAcctName << "\n"; cout << "Account Number: "; for(int j = 0; j < 13; j++) { char input_number; stringstream converter; checkFile.get(input_number); converter << input_number; converter >> acctNumber[j]; cout << acctNumber[j]; } // if balance a problem, try the below commented out line // checkFile.ignore(numeric_limits<streamsize>::max(), '\n'); cout << endl; checkFile >> acctBalance; cout << "Balance: $" << fixed << showpoint << setprecision(2) << acctBalance << endl; } else fatal("[!!] Invalid Account\n"); checkFile.close(); getchar(); } void Checking::transferFromSaving() // Move funds FROM SAVINGS to CHECKING { system("cls"); string name; long checkPos = 0; long savePos = 0; float savingBalance = 0; string saveAcctName; int i = 0; cin.clear(); fstream saveFile("saving.dat", ios::in | ios::out | ios::beg); fstream checkFile("checking.dat", ios::in | ios::out | ios::beg); cout << "\t\t-=[ Funds Transfer ]=-" << endl; cout << "\t\t-=[ Savings to Checking ]=-" << endl; cout << "Account Name: "; cin.sync(); getline(cin, name); getline(checkFile, checkAcctName); while(name != checkAcctName && !checkFile.fail()) { i++; getline(checkFile, checkAcctName); } getline(saveFile, saveAcctName); while(name != saveAcctName && !saveFile.fail()) { i = 0; i++; getline(saveFile, saveAcctName); } if(name == checkAcctName) { cout << "Amount to transfer: $"; float depAmt = 0; cin >> depAmt; for(int j = 0; j < 13; j++) { char input_number; stringstream converter; checkFile.get(input_number); converter << input_number; converter >> acctNumber[j]; } checkPos = checkFile.tellg(); // if the file is found, get the position of acctBalance and store it in ptrPos checkFile.seekg(checkPos); checkFile >> acctBalance; savePos = saveFile.tellg(); saveFile.seekg(savePos); // sending the cursor in the file to ptrPos + 1 to ignore white space saveFile >> savingBalance; if(savingBalance < depAmt) // if checking account does not have enough funds, exit with NSF code fatal("[!!] Insufficient Funds\n"); acctBalance += depAmt; // can be changed to an overloaded operator savingBalance -= depAmt; // can be changed to an overloaded operator checkFile.seekp(checkPos); // go to position previously set above checkFile << acctBalance; // write new balance to checkFile saveFile.seekp(savePos); // same thing as above comment saveFile << savingBalance; // write new balance to saveFile cout << "New Balance in Checking: $" << acctBalance << endl; // will be removed later cout << "New Balance in Savings: $" << savingBalance << endl; // will be removed later aswell } else fatal("[!!] Linked accounts do not exist.\n"); // if account is not found saveFile.close(); checkFile.close(); } /******************************************************** ******************************************************** SAVING ACCOUNT CODE ********************************************************* *********************************************************/ void Saving::newSavingAccount() { system("cls"); ofstream saveFile("saving.dat", ios::out | ios::app); // For saving savings accounts cout << "\t\t -=[ New Savings Account ]=- \n" << endl; cout << "Name of the main holder to be on account: "; getline(cin, saveAcctName); cout << "Deposit Amount: $"; cin >> initSaveDeposit; if(initSaveDeposit <= 0) { while(initSaveDeposit <= 0) { invalid("[!!]0 or negative value entered.\nPerhaps a typo?\n"); cout << "Deposit amount: $"; cin >> initSaveDeposit; } } if(!saveFile) fatal("[!!] Fatal Error 251: Miscommunication with server\n"); saveFile << saveAcctName << endl; for(int j = 0; j < 13; j++) { acctNumber[j] = (rand() % 10); saveFile << acctNumber[j]; } saveFile << endl; saveFile << initSaveDeposit << endl; saveFile.close(); } void Saving::viewSavingBalance() { string name; int i = 0; fstream saveFile("saving.dat", ios::in | ios::beg); cin.clear(); system("cls"); cout << "\t\t -=[ View Saving Account ]=-\n\n" << endl; cout << "Account Name: "; cin.sync(); getline(cin, name); getline(saveFile, saveAcctName); while(name != saveAcctName && !saveFile.fail()) { i++; getline(saveFile, saveAcctName); } if(name == saveAcctName) { system("cls"); cout << "\t\t -=[ Saving Account Balance ]=-\n\n" << endl; cout << "Account Name: " << saveAcctName << "\n"; cout << "Account Number: "; for(int j = 0; j < 13; j++) { char input_number; stringstream converter; saveFile.get(input_number); converter << input_number; converter >> acctNumber[j]; cout << acctNumber[j]; } // if balance a problem, try the below commented out line // checkFile.ignore(numeric_limits<streamsize>::max(), '\n'); cout << endl; saveFile >> acctBalance; cout << "Balance: $" << fixed << showpoint << setprecision(2) << acctBalance << endl; } else fatal("[!!] Invalid Account\n"); saveFile.close(); getchar(); } // NEED TO WORK ON THIS PORTION TOMORROW AND MONDAY, ADD OVERLOADED OPS FOR ASSIGNMENT!!!!!!! void Saving::transferFromChecking() // This is to take money FROM checking and ADD IT TO SAVING { system("cls"); string name; long savePos = 0; long checkPos = 0; float checkingBalance = 0; string checkAcctName; int i = 0; cin.clear(); fstream saveFile("saving.dat", ios::in | ios::out | ios::beg); fstream checkFile("checking.dat", ios::in | ios::out | ios::beg); cout << "\t\t-=[ Funds Transfer ]=-" << endl; cout << "\t\t-=[ Checking to Savings ]=-" << endl; cout << "Account Name: "; cin.sync(); getline(cin, name); getline(saveFile, saveAcctName); getline(checkFile, checkAcctName); while(name != saveAcctName && name != checkAcctName && !saveFile.fail() && !checkFile.fail()) { i++; getline(saveFile, saveAcctName); getline(checkFile, checkAcctName); } if(name == saveAcctName) { cout << "Amount to transfer: $"; float depAmt = 0; cin >> depAmt; for(int j = 0; j < 13; j++) { char input_number; stringstream converter; saveFile.get(input_number); converter << input_number; converter >> acctNumber[j]; } savePos = saveFile.tellg(); // if the file is found, get the position of acctBalance and store it in ptrPos saveFile.seekg(savePos); saveFile >> acctBalance; checkPos = checkFile.tellg(); checkFile.seekg(checkPos); // if file is found, store current position of the cursor to ptrPos checkFile >> checkingBalance; if(checkingBalance < depAmt) // if checking account does not have enough funds, exit with NSF code fatal("[!!] Insufficient Funds\n"); // Can also place overloaded op here acctBalance += depAmt; // can be changed to an overloaded operator checkingBalance -= depAmt; // can be changed to an overloaded operator saveFile.seekg(savePos); // go to position previously set above saveFile << acctBalance; // write new balance to saveFile checkFile.seekg(checkPos); // same thing as above comment checkFile << checkingBalance; // write new balance to checkFile cout << "New Balance in Savings: $" << acctBalance << endl; // will be removed later cout << "New Balance in Checking: $" << checkingBalance << endl; // will be removed later aswell } else fatal("[!!] Linked accounts do not exist.\n"); // if account is not found saveFile.close(); checkFile.close(); } /******************************************** ******************************************** CHECK AND SAVE CODE ********************************************** **********************************************/ void checkAndSave::newCheckAndSave() { system("cls"); ofstream saveFile("saving.dat", ios::out | ios::app); // For saving savings accounts ofstream checkFile("checking.dat", ios::out | ios::app); // For saving checking accounts cout << "\t -=[ New Checking & Saving Account ]=- \n" << endl; cout << "Name of the main holder to be on account: "; getline(cin, checkAcctName); saveAcctName = checkAcctName; cout << "Checking Deposit Amount: $"; cin >> initCheckDeposit; if(initCheckDeposit <= 0) { while(initCheckDeposit <= 0) { invalid("[!!] 0 or negative amount entered\nMaybe a typo?\n"); cout << "Deposit Amount: $"; cin >> initCheckDeposit; } } cout << "Saving Deposit Amount: $"; cin >> initSaveDeposit; if(initSaveDeposit <= 0) { while(initSaveDeposit <= 0) { invalid("[!!]0 or negative value entered.\nPerhaps a typo?\n"); cout << "Deposit amount: $"; cin >> initSaveDeposit; } } if(!saveFile || !checkFile) fatal("[!!] Fatal Error 251: Miscommunication with server\n"); checkFile << checkAcctName << endl; saveFile << saveAcctName << endl; for(int j = 0; j < 13; j++) { acctNumber[j] = (rand() % 10); checkFile << acctNumber[j]; saveFile << acctNumber[j]; } saveFile << endl; saveFile << initSaveDeposit << endl; checkFile << endl; checkFile << initCheckDeposit << endl; checkFile.close(); saveFile.close(); } void checkAndSave::viewBothBalances() { string name; int i = 0; fstream checkFile("checking.dat", ios::in | ios::beg); fstream saveFile("saving.dat", ios::in | ios::beg); system("cls"); cin.clear(); cout << "\t-=[ Saving & Checking Account Balance ]=-\n\n" << endl; cout << "Account Name: "; cin.sync(); getline(cin, name); getline(checkFile, checkAcctName); saveAcctName = name; /**********************\ | Checking Account portion | | of the checking & savings | | overview | \**********************/ while(name != checkAcctName && !checkFile.fail()) { i++; getline(checkFile, checkAcctName); } system("cls"); if(name != checkAcctName && checkFile.fail()) invalid("\n\n[!!] No Checking Account Found\n"); cout << "\t\t -=[ Checking Account ]=- \n" << endl; cout << "Account Name: " << checkAcctName << "\n"; cout << "Account Number: "; for(int j = 0; j < 13; j++) { char input_number; stringstream converter; checkFile.get(input_number); converter << input_number; converter >> acctNumber[j]; cout << acctNumber[j]; } // if balance a problem, try the below commented out line // checkFile.ignore(numeric_limits<streamsize>::max(), '\n'); cout << endl; checkFile >> acctBalance; cout << "Balance: $" << fixed << showpoint << setprecision(2) << acctBalance << endl; /*********************\ | Saving Account portion | | of the checking & saving | | overview | \*********************/ getline(saveFile, saveAcctName); while(name != saveAcctName && !saveFile.fail()) { i++; getline(saveFile, saveAcctName); } if(name != saveAcctName && saveFile.fail()) invalid("\n\n[!!] No Saving Account Found\n"); if(name == saveAcctName) { cout << "\t\t -=[ Saving Account ]=-\n\n" << endl; cout << "Account Name: " << saveAcctName << "\n"; cout << "Account Number: "; for(int j = 0; j < 13; j++) { char input_number; stringstream converter; saveFile.get(input_number); converter << input_number; converter >> acctNumber[j]; cout << acctNumber[j]; } // if balance a problem, try the below commented out line // checkFile.ignore(numeric_limits<streamsize>::max(), '\n'); cout << endl; saveFile >> acctBalance; cout << "Balance: $" << fixed << showpoint << setprecision(2) << acctBalance << endl; } if(name != saveAcctName && name != checkAcctName && saveFile.fail() && checkFile.fail()) fatal("[!!] No Accounts Have Been Found\n"); checkFile.close(); saveFile.close(); getchar(); } Main.cpp #include <iostream> #include "MainBankClass.h" using namespace std; int main() { Banking bank; Checking check; Saving save; checkAndSave CanS; char choice; choice = bank.menu(); // Call the banking menu switch(choice) { case 'A': choice = bank.newAccountMenu(); switch(choice) { case 'A': check.newCheckingAccount(); break; case 'B': save.newSavingAccount(); break; case 'C': CanS.newCheckAndSave(); break; default: system("cls"); bank.fatal("[!!] Invalid option\n"); break; } break; /***********************************************/ case 'B': choice = bank.getBalanceChoice(); switch(choice) { case 'A': check.viewCheckingBalance(); break; case 'B': save.viewSavingBalance(); break; case 'C': CanS.viewBothBalances(); break; default: bank.fatal("Invalid decision\n"); break; } /*************************************************/ break; case 'C': check.transferFromSaving(); break; case 'D': save.transferFromChecking(); break; case 'E': system("cls"); cout << "\t\t-=[ Disconnecting From System ]=-\n"; cout << "\t\t\t Thank you" << endl; cout << "\t\t Have a nice day!" << endl; exit(1); break; default: system("cls"); bank.invalid("\n\n\n\n\t\t [+] Invalid Selection \n\t\t[+] Disconnecting From System \n\t\t\tGood-bye \n\n\n\n\n\n\n"); exit(1); break; } return 0; }

  Read the article

• Windows CE Chat Transcript (March 30, 2010)

  - by Bruce Eitman

  For those of you who missed the chat today, here is the raw transcript.   By raw, I mean that I copied and pasted the discussion without any edits. This is divided into two parts, the top part is the answers from the Microsoft Experts and the bottom part is the questions from the audience. Answers from Microsoft:   Karel Danihelka [MS] (Expert)[2010-3-30 12:2]: Hi everyone, my name is Karel Danihelka and I am developer in partner response team. Sing Wee [MS] (Expert)[2010-3-30 12:2]: Hi, I'm Sing Wee, part of the CoreOS/BSP Test Team. GLanger_MS (Expert)[2010-3-30 12:2]: Hi, I'm Glen Langer, program manager on the Core Team. Karel Danihelka [MS] (Expert)[2010-3-30 12:3]: Q: I need to implement hardware timers on my windows CE 6.0 device to trigger events at microsecond intervals. Where should i start? A: Until you are using CPU with GHz frequency your only chance is use interrupt handler and implement all funcionality there. But it will be really tricky and may reduce system performance. If period will be near to millisecond timeframe you can use normal thread wait for event pattern. Karel Danihelka [MS] (Expert)[2010-3-30 12:5]: Q: I want to partition my NAND Flash device. One partition to use for hive ragistry and the other for the apps and data. The only way to do it is programmatically or setting some registry values ? A: It need to be set in registry - generally you need mark this partition as boot partition. Karel Danihelka [MS] (Expert)[2010-3-30 12:7]: Q: My CPU is Intel celeron M processor 1Ghz. A: In this case you can try use normal approach - in interrupt handler return SYSINTR and start thread in device driver which will spin thread waiting on event attached to this SYSINTR. Karel Danihelka [MS] (Expert)[2010-3-30 12:7]: Q: If i need to implement it using interrupt handlers, What are all the files that I should look at? A: Good quesiton - I would recommend documentation and there was BSP development book to download for free. mikehall_ms (Moderator)[2010-3-30 12:8]: Q: Hi guys, what's the formal way to report bugs back to the core team / product team? The mechanism of calling the support phone number every time is really onerous and time-consuming. Is there another mechanism? A: Using product support is the formal way to report bugs/issues - Product support can then create an issue that can be tracked. Karel Danihelka [MS] (Expert)[2010-3-30 12:9]: Q: But the operation for creating the partitions ? A: This is tricky - if you will make it autopartition & autoformat it will be created by filesystem. But generally it depends on your boot loader. mikehall_ms (Moderator)[2010-3-30 12:10]: Q: Is Windows Phone 7 related to Windows CE? If so, can you tell me what version of Windows CE is the basis? Is it in fact the new version of Windows Mobile? A: At MIX 2010 Charlie Kindel presented a session that described some of the core technologies that make up Windows Phone 7 Series, including the underlying operating system (Windows CE) and the new ISV programming model based on Silverlight and .NET - check out the Mix Online Videos to get more information. davbo-msft (Moderator)[2010-3-30 12:10]: Q: Is Windows Phone 7 related to Windows CE? If so, can you tell me what version of Windows CE is the basis? Is it in fact the new version of Windows Mobile? A: This forum is to discussed released products in the industry. Windows Mobile & Windows CE are based on the same Windows CE Kernel/system. Windows CE is focused on deliverying the OS for embedded customers in the market where Windows Mobile is focused on deliverying compelling Windows Phone platform. davbo-msft (Moderator)[2010-3-30 12:11]: Q: Is Windows Phone 7 related to Windows CE? If so, can you tell me what version of Windows CE is the basis? Is it in fact the new version of Windows Mobile? A: http://en.wikipedia.org/wiki/Windows_CE Wikipedia gives a good breakdown of the version history. Travis Hobrla [MS] (Expert)[2010-3-30 12:13]: Q: I created a OS design with KITL and kernel debugger enabled. But I am unable to connect to the target for debugging. I am getting the following error when i try to connect with the device. PB Debugger Cannot initialize the Kernel Debugger. PB Debugger Debugger could not initialize connection. PB Debugger The Kernel Debugger is waiting to connect with target. PB Debugger The Kernel Debugger has been disconnected successfully. A: One possibility is that a rogue cesvchost.exe has co-opted the debugger. I am assuming this is CE 6.0? Can you try exiting visual studio and manually killing the cesvchost.exe process from the Task Manager? davbo-msft (Moderator)[2010-3-30 12:14]: Q: Hi guys, what's the formal way to report bugs back to the core team / product team? The mechanism of calling the support phone number every time is really onerous and time-consuming. Is there another mechanism? A: For info on contacting Microsoft support refer to the support page on the Embedded website: http://msdn.microsoft.com/en-us/windowsembedded/dd897633.aspx Sing Wee [MS] (Expert)[2010-3-30 12:16]: Q: Do u mean ISR/IST implementation? How can i register an interrupt? What kind of interrupt should i register? A: A good introduction to interrupts in WinCE 6.0 can be found here (aside from the documentation on MSDN): http://download.microsoft.com/download/9/c/f/9cffaa58-4000-48d6-a4b2-5fed9e4e6410/Chapter%206%20-%20Developing%20Device%20Drivers.pdf mikehall_ms (Moderator)[2010-3-30 12:16]: Q: What will be different in Windows Compact 7 from CE 6.0? A: Unfortunately we cannot discuss unreleased products on this chat - keep an eye on the Windows Embedded web site and blogs to keep up to date with product announcements. Travis Hobrla [MS] (Expert)[2010-3-30 12:16]: Q: I am using CE 6.0. There is no cesvchost process running in my system. A: What operating system are you using? Karel Danihelka [MS] (Expert)[2010-3-30 12:16]: Q: So...I have to modify file system code to create 2 partition at system startup ?!! I haven't understood.... A: You don't need to modify code, there are registry settings to achive this (look to documentation). But you may need to create partition table in boot loader. Unfortunatelly there isn't simple way how to do it. davbo-msft (Moderator)[2010-3-30 12:18]: Q: I would like to get a handle to a Silverlight screen section, is that possiable? A: Windows Embedded CE 6.0 R3 includes Sliverlight for Windows Embedded. Refer to New Features overview on the embedded web site. http://www.microsoft.com/windowsembedded/en-us/products/windowsce/default.mspx. Silverlight - The power of Silverlight brought to Windows Embedded CE to create rich applications and user interfaces is new part of Windows CE Embedded. mikehall_ms (Moderator)[2010-3-30 12:20]: Q: The link for developing device drivers is not working. can u please check that? A: http://msdn.microsoft.com/en-us/library/ms923714.aspx davbo-msft (Moderator)[2010-3-30 12:20]: Q: I would like to get a handle to a Silverlight screen section, is that possiable? A: Sorry misunderstood the question I thought you were asking if embedded CE could handle Silverlight. Please repost so that the question goes back into the active queue because once answered no way to put the status back to open. Travis Hobrla [MS] (Expert)[2010-3-30 12:21]: Q: sorry! Windows XP SP3 A: Can you try exiting VS2005 and confirming cesvchost.exe is not running, then renaming C:\Documents and Settings\USERNAME\Local Settings\Application Data\Microsoft\CoreCon\1.0 to 1.0_backup, then restarting VS2005? Sing Wee [MS] (Expert)[2010-3-30 12:24]: Q: Can I have the book's name please? A: I believe the downloadable version is related to the last link I sent. If you go to the following website, I believe you can download the whole thing: http://msdn.microsoft.com/en-us/windowsembedded/ce/cc294468.aspx davbo-msft (Moderator)[2010-3-30 12:24]: Q: If one has an image on a Silverlight page, it seems to be cached. How would one refresh that cache after changing the underlying image? A: change the URI of the image or use a writeable bitmap if they want to manually toggle the pixels Sing Wee [MS] (Expert)[2010-3-30 12:25]: A: Whoops, hit [ENTER] too early. On the right side, you'll see there an "Exam Preparation Kit" link that can be downloaded in several different languages. Sing Wee [MS] (Expert)[2010-3-30 12:25]: Q: Can I have the book's name please? A: Whoops, hit [ENTER] too early. On the right side, you'll see there an "Exam Preparation Kit" link that can be downloaded in several different languages. Karel Danihelka [MS] (Expert)[2010-3-30 12:26]: Q: I have a NAND Flash on my target device. On this flash I have the hive registry and an application.I have observed that when the NAND flash is fully, the system startup time is longer....is there a degradation of NAND use that influences the startup time ? Why ? A: Yes - on boot flash abstraction library (old one) read metadata from all sectors to rebuild physical - logical mapping table. davbo-msft (Moderator)[2010-3-30 12:27]: Q: I would like to get a handle to a Silverlight screen section, is that possiable? A: Need addition info on this question. Can you provide more details on what you are trying to do in Silverlight? davbo-msft (Moderator)[2010-3-30 12:27]: Q: If one has an image on a Silverlight page, it seems to be cached. How would one refresh that cache after changing the underlying image? A: Additonal Info: if you want to manually touch the pixels use WriteableBitmap if you want to use the underlying HWND then use IXRVisualHost::GetHWND() davbo-msft (Moderator)[2010-3-30 12:28]: Q: Writable bitmap, is there an example of the syntax? A: if you want to manually touch the pixels use WriteableBitmap if you want to use the underlying HWND then use IXRVisualHost::GetHWND() davbo-msft (Moderator)[2010-3-30 12:29]: Q: I would like to get a handle to a Silverlight screen section, is that possiable? A: Can I get more information about this question about what you are trying to accomplish in Silverlight? davbo-msft (Moderator)[2010-3-30 12:31]: Q: IXRVisualHost::GetHWND() exactly what I needed Thanks, A: Your welcome Sing Wee [MS] (Expert)[2010-3-30 12:31]: Q: ok. thanks for the book's link A: No problem. Travis Hobrla [MS] (Expert)[2010-3-30 12:32]: Q: Typically for SoC devices you name your hardware specific libraries in the form "SOCDIRNAME_LIBNAME". In our platform "OMAP35XX_TPS659XX_TI_V1" if you do this we cause the catalog parser to die... For example if we have a library "Musbfn_OMAP35XX_TPS659XX_TI_V1.dll" entering this in the catalogs pbcxml file in a <module> section causes the XML parser to fail with : Error 3 The 'urn:Microsoft.PlatformBuilder/Catalog:Module' element is        invalid - The value '012345678901234567890123456789.dll' is invalid         according to its datatype         'urn:Microsoft.PlatformBuilder/Catalog:CatalogFileName' - The actual         length is greater than the MaxLength value. A: There are a couple workarounds I can think of. I believe the Module element is only used when doing SYSGEN parsing to make sure dependent SYSGENs are present when the item is selected, so I believe it is optional to the catalog. The other obvious workaround is to shorten the soc name. I realize neither of these solutions is ideal. This is not something we anticipated when we tested CE6.0, sorry. Travis Hobrla [MS] (Expert)[2010-3-30 12:33]: Q: I am getting this error only when I select the KdStub as the debugger in Target device connectivity. A: Right, but KdStub is the debugger that you should use. Have you tried the steps I suggested? Travis Hobrla [MS] (Expert)[2010-3-30 12:36]: Q: If I select Active KTIL, My OS doesn't boots. It says "loading NK.EXE at 0x<xxxxx> location" after that nothing comes in the debug log. A: Can you look at the serial debug output and see what is happening there? Often it can give you a clue to the KITL driver malfunctioning. Travis Hobrla [MS] (Expert)[2010-3-30 12:38]: Q: I have tried that and I am getting the same error. A: I am assuming you have a device created in Target -> Connectivity Options in Platform Builder. What are the Kernel download / Kernel transport for your device? Travis Hobrla [MS] (Expert)[2010-3-30 12:40]: Q: KITL: *** Device Name CEPC56059 *** WARN: KITL will run in polling mode VBridge:: built on [Jul 10 2009] time [10:20:14] VBridgeInit()...TX = [16384] bytes -- Rx = [16384] bytes Tx buffer [0xA1B84860] to [0xA1B88860]. Rx buffer [0xA1B88880] to [0xA1B8C880]. VBridge:: NK add MAC: [0-60-65-2-DA-FB] Connecting to Desktop KITL: Connected host IP: 1 Port: 1086 .. this is the output of the serial debug A: This looks reasonable and does not give clues as to why boot would halt at that point. If you capture a network trace or turn on KITL debug zones via dpCurSettings in kitl.dll, do you see KITL active after this? Travis Hobrla [MS] (Expert)[2010-3-30 12:41]: Q: Both is happening via Ethernet. A: Only thing I have left to suggest is a Platform Builder installation Repair, then. Karel Danihelka [MS] (Expert)[2010-3-30 12:42]: Q: Hi, I saw that the ATADISK is quite generic and des not have any optimizations. Do you have any advice to consider while tryin to improve the performance of it? A: If I remember correctly sample code has support for some specific hardware controllers (little obsolete now). This should be good start point (if you will not decide take existing driver as sample and write you own). Travis Hobrla [MS] (Expert)[2010-3-30 12:44]: Q: I didn't do that. I have to try. A: I think that's the next valid step. You need to figure out whether KITL is hanging or the device - use instrumented serial debug messages and network trace to determine this. Sing Wee [MS] (Expert)[2010-3-30 12:46]: Q: KITL: *** Device Name CEPC56059 *** WARN: KITL will run in polling mode VBridge:: built on [Jul 10 2009] time [10:20:14] VBridgeInit()...TX = [16384] bytes -- Rx = [16384] bytes Tx buffer [0xA1B84860] to [0xA1B88860]. Rx buffer [0xA1B88880] to [0xA1B8C880]. VBridge:: NK add MAC: [0-60-65-2-DA-FB] Connecting to Desktop KITL: Connected host IP: 1 Port: 1086 .. this is the output of the serial debug A: Neo, have you by any chance tried looking into your firewall to see if it might be blocking traffic on any particular ports? Wireshark/netmon might be able to help you here if that's the issue. davbo-msft (Moderator)[2010-3-30 12:48]: Q: I lost spell check, how can i get it back A: Hello - can you give additional details about your question? Is this related to a Windows CE Embedded application? masatos_MSFT (Expert)[2010-3-30 12:51]: Q: When attempting to run the CETK cellcore tests the documentation states the pre-requisites include "stinger.ini", "ltk.ini" but windows CE doesn't provide these or document what they fully need to contain. Implicitly you also need "datatrans.xml" which isn't supplied. If you get around this error and steal these from Windows Mobile instead, when you try and run the CETK tests you get a data abort in radiometricsdll.dll. How should we invoke the cellcore parts of CETK? A: Hi Pev, what version of Windows CE and CETK are you using? I do not have the expertise to answer this question, but can find somebody who can. Travis Hobrla [MS] (Expert)[2010-3-30 12:52]: Q: I don't see a kitlcore.dll in my OS. is my debug image fails to load because of that? A: kitl.dll should be all that's needed, kitlcore.lib is linked into that. Travis Hobrla [MS] (Expert)[2010-3-30 12:55]: Q: I've got a platform (not developed by myself) where I2C bus support has to be provided through the OAL as the kernel needs to talk to devices such as the power management IC and gas gauge so a 'proper' I2C driver hanging off device manager isn't possible. This happens to be a polled driver, so obviously it hits the system hard when either under lots of traffic or an error condition occurs and the driver constantly polls. I originally thought that there was no straightforward way to make such code interrupt driven in the kernel (as it's a cludge) but I realised that that's exactly what ETHDBG drivers do. Is there any reason why I shouldn't have a go at implementing a similar mechanism for our kernel resident I2C driver? If not, are there any obvious pitfalls - I've not seen any other BSP's do this in the past... A: You can make a 'proper' driver that calls down into the OAL to do the actual I2C transactions. Alternatively you can build an interrupt-based version in the OAL where you handle everything in the ISR. There is nothing wrong with that so long as the rest of your drivers and app threads can handle longer times with interrupts off while you are servicing I2C interrupts. Sing Wee [MS] (Expert)[2010-3-30 12:55]: Q: I am having trouble with my mouse, I have the microsoft wireless mobile mouse 3000, when I push the scroll button I am suppose to have autoscroll instead it shows other web pages,Can you help me out tell me what to do!!! A: Sorry, this current chat is about Windows Embedded Compact. Hope you're able to find an answer to your question elsewhere. davbo-msft (Moderator)[2010-3-30 12:56]: Q: Is the Silverlight Animation "Spline" a BezierSpline? A: Spline - http://msdn.microsoft.com/en-us/library/ee501495.aspx<BR< a>>   masatos_MSFT (Expert)[2010-3-30 12:57]: Thanks for the info Pev. I will follow up with the CETK experts here and get back to you. davbo-msft (Moderator)[2010-3-30 12:59]: Q: Spline- bad link A: http://msdn.microsoft.com/en-us/library/ee501495.aspx davbo-msft (Moderator)[2010-3-30 13:0]: Q: Sorry, got to tirm the ">" A: No Worries http://msdn.microsoft.com/en-us/library/ee501495.aspx davbo-msft (Moderator)[2010-3-30 13:0]: Hello everyone, we are just about out of time. Thank you for joining us for our Windows Embedded CE 6.0 chat today! <http://www.Microsoft.com/Embedded>; A special thank you to the product group members for coming out. The transcript of today’s chat will be posted online as soon as possible, to <http://msdn.microsoft.com/en-us/chats>;. We’ll see you again for another chat next month. Please check <http://msdn.microsoft.com/en-us/chats>; for the list of upcoming chats. If you still have unanswered questions, let me suggest that you post them on one of our newsgroups on <http://msdn.microsoft.com/en-us/windowsembedded/ce/default.aspx> -Windows Embedded CE 6.0 R3 Now Available! <http://msdn.microsoft.com/windowsembedded/ce/dd630616.aspx>; davbo-msft (Moderator)[2010-3-30 13:1]: Q: hi everybody. I would like to know if there is something know about a bug in RTC API (VOIP), especially when using SIP. According the to the analysis with application verifyier there is a heap link in rtcdllmedia.dll. All of the unreleased chunks seem to have a size of 6560 bytes. A: I will follow up with the Networking Team for a response. davbo-msft (Moderator)[2010-3-30 13:1]: Q: Hi, we've problems with debugging of applications (= breakpoints in Platform Builder will be ignored) over KITL on Windows CE 5.0, if the PDB files are large (over 60MB). Are there any limitations to size of the PDB files? A: I will follow up with the tools team for a response and post with the transcript. Sing Wee [MS] (Expert)[2010-3-30 13:1]: Q: I am unable to use the target control in my development environment. any ideas? A: Make sure you have SYSGEN_SHELL=1 set in your build environment. davbo-msft (Moderator)[2010-3-30 13:3]: Q: what are the main differences between Object Store and RAM disk ? They are both in RAM...are there performance differences ? access differences ? A: I will follow up with the Core Team and get a response posted with the transcript to MSDN  The Questions   [2010-3-30 12:57]: Thanks for the info Pev. I will follow up with the CETK experts here and get back to you. [2010-3-30 12:59]:   [2010-3-30 13:0]:   [2010-3-30 13:0]: Hello everyone, we are just about out of time. Thank you for joining us for our Windows Embedded CE 6.0 chat today! <http://www.Microsoft.com/Embedded>; A special thank you to the product group members for coming out. The transcript of today’s chat will be posted online as soon as possible, to <http://msdn.microsoft.com/en-us/chats>;. We’ll see you again for another chat next month. Please check <http://msdn.microsoft.com/en-us/chats>; for the list of upcoming chats. If you still have unanswered questions, let me suggest that you post them on one of our newsgroups on <http://msdn.microsoft.com/en-us/windowsembedded/ce/default.aspx> -Windows Embedded CE 6.0 R3 Now Available! <http://msdn.microsoft.com/windowsembedded/ce/dd630616.aspx>; [2010-3-30 13:1]: [2010-3-30 13:1]: [2010-3-30 13:1]: [2010-3-30 13:3]: neo (Guest)[2010-3-30 11:37]: Hi all KellyG (Guest)[2010-3-30 11:37]: Hi KellyG (Guest)[2010-3-30 11:37]: I have a question unrelated to windows Ce embedded, can you please help me?? neo (Guest)[2010-3-30 11:38]: I need to implement hardware timers on my windows CE 6.0 device to trigger events at microsecond intervals! c neo (Guest)[2010-3-30 11:38]: yes. post it. May be i cud give a try KellyG (Guest)[2010-3-30 11:38]: My Product key listed on my tower is not the product key I need for microsoft office, but that is the only product key listed. neo (Guest)[2010-3-30 11:39]: I hope this is a chat for windows embedded. please post ur queries in office forums KellyG (Guest)[2010-3-30 11:39]: it is but i could not find a forum for office neo (Guest)[2010-3-30 11:40]: I think moderators will help u out. @ davbo-msft: can u help this guy? neo (Guest)[2010-3-30 11:41]: Q: I need to implement hardware timers on my windows CE 6.0 device to trigger events at microsecond intervals. Where should i start? davbo-msft (Moderator)[2010-3-30 11:50]: Our chat today covers the topic of Windows Embedded CE! 1. This chat will last for one hour. During this hour, our Experts will respond to as many questions as they can. Please understand that there may be some questions we cannot respond to due to lack of information or because the information is not yet public. 2. We encourage you to submit questions for our Experts. To do so, type your questions in the send box, select the “ask the Experts” box and click SEND. Questions sent directly to the Guest Chat room will not be answered by the Experts, but we encourage other community members to assist. 3. We ask that you stay on topic for the duration of the chat. This helps the Guests and Experts follow the conversation more easily. We invite you to ask off topic questions after this chat is over, but not during. 4. Please abide by the Chat Code of Conduct. Chat code of conduct: <http://msdn.microsoft.com/chats/chatroom.aspx?ctl=hlp#Conduct>; Pev (Guest)[2010-3-30 11:54]: Evening! davbo-msft (Moderator)[2010-3-30 11:54]: Hello everyone this is Dave Boyce - I worked in the Multimedia area for Windows CE. neo (Guest)[2010-3-30 11:55]: hello dave neo (Guest)[2010-3-30 11:55]: The chat code of conduct link is not working! Pev (Guest)[2010-3-30 11:56]: Best be polite just in case then ;-) neo (Guest)[2010-3-30 11:56]: davbo-msft (Moderator)[2010-3-30 11:57]: I'll check out the issue w/ the link paolopat (Guest)[2010-3-30 12:0]: Hello davbo-msft (Moderator)[2010-3-30 12:0]: We are pleased to welcome our Experts for today’s chat. I will have them introduce themselves now. Chat will begin in a couple of minutes. <http://www.Microsoft.com/Embedded>; paolopat (Guest)[2010-3-30 12:3]: Hello Experts ! neo (Guest)[2010-3-30 12:3]: Welcome all! paolopat (Guest)[2010-3-30 12:3]: Q: I want to partition my NAND Flash device. One partition to use for hive ragistry and the other for the apps and data. The only way to do it is programmatically or setting some registry values ? neo (Guest)[2010-3-30 12:3]: Q: I need to implement hardware timers on my windows CE 6.0 device to trigger events at microsecond intervals. Where should i start? neo (Guest)[2010-3-30 12:5]: Q: My CPU is Intel celeron M processor 1Ghz. Pev (Guest)[2010-3-30 12:5]: neo: if your silicon has multiple general purpose timers, pick one that's not in use for the system timer / profiler and set it up to trigger irqs for your purpose. You can't guarantee hard realtime type responses though... GarySwalling (Guest)[2010-3-30 12:5]: Q: Is Windows Phone 7 related to Windows CE? If so, can you tell me what version of Windows CE is the basis? Is it in fact the new version of Windows Mobile? Pev (Guest)[2010-3-30 12:6]: Q: Hi guys, what's the formal way to report bugs back to the core team / product team? The mechanism of calling the support phone number every time is really onerous and time-consuming. Is there another mechanism? paolopat (Guest)[2010-3-30 12:6]: Q: But the operation for creating the partitions ? neo (Guest)[2010-3-30 12:6]: Q: If i need to implement it using interrupt handlers, What are all the files that I should look at? GPM (Guest)[2010-3-30 12:6]: Q: I would like to get a handle to a Silverlight screen section, is that possiable? Jhony (Guest)[2010-3-30 12:7]: Q: I created a OS design with KITL and kernel debugger enabled. But I am unable to connect to the target for debugging. I am getting the following error when i try to connect with the device. PB Debugger Cannot initialize the Kernel Debugger. PB Debugger Debugger could not initialize connection. PB Debugger The Kernel Debugger is waiting to connect with target. PB Debugger The Kernel Debugger has been disconnected successfully. Charles (Guest)[2010-3-30 12:7]: What will be different in Windows Compact 7 from CE 6.0? neo (Guest)[2010-3-30 12:8]: Can I have the book's name please? kiefs_dev (Guest)[2010-3-30 12:8]: Q: hi everybody. I would like to know if there is something know about a bug in RTC API (VOIP), especially when using SIP. According the to the analysis with application verifyier there is a heap link in rtcdllmedia.dll. All of the unreleased chunks seem to have a size of 6560 bytes. paolopat (Guest)[2010-3-30 12:10]: Q: So...I have to modify file system code to create 2 partition at system startup ?!! I haven't understood.... neo (Guest)[2010-3-30 12:10]: Q: Do u mean ISR/IST implementation? How can i register an interrupt? What kind of interrupt should i register? neo (Guest)[2010-3-30 12:11]: Q: Can I have the book's name please? Charles (Guest)[2010-3-30 12:11]: Q: What will be different in Windows Compact 7 from CE 6.0? PaulT (Guest)[2010-3-30 12:11]: neo: I'd say that you really need the docs for YOUR BSP, not generic documents for BSPs in general. Each BSP may be architected differently. If you're using the CEPC BSP, then the documentation that comes with Platform Builder is a reasonable place to look. GPM (Guest)[2010-3-30 12:11]: Q: If one has an image on a Silverlight page, it seems to be cached. How would one refresh that cache after changing the underlying image? Elektrobit (Guest)[2010-3-30 12:12]: Q: Hi, we've problems with debugging of applications (= breakpoints in Platform Builder will be ignored) over KITL on Windows CE 5.0, if the PDB files are large (over 60MB). Are there any limitations to size of the PDB files? Jhony (Guest)[2010-3-30 12:15]: Q: I am using CE 6.0. There is no cesvchost process running in my system. alexquisi (Guest)[2010-3-30 12:15]: Q: Hi, I saw that the ATADISK is quite generic and des not have any optimizations. Do you have any advice to consider while tryin to improve the performance of it? Jhony (Guest)[2010-3-30 12:17]: Windows XP service pack 1 Jhony (Guest)[2010-3-30 12:17]: Q: sorry! Windows XP SP3 neo (Guest)[2010-3-30 12:19]: Q: The link for developing device drivers is not working. can u please check that? paolopat (Guest)[2010-3-30 12:20]: Q: I have a NAND Flash on my target device. On this flash I have the hive registry and an application.I have observed that when the NAND flash is fully, the system startup time is longer....is there a degradation of NAND use that influences the startup time ? Why ? Pev (Guest)[2010-3-30 12:20]: Q: When attempting to run the CETK cellcore tests the documentation states the pre-requisites include "stinger.ini", "ltk.ini" but windows CE doesn't provide these or document what they fully need to contain. Implicitly you also need "datatrans.xml" which isn't supplied. If you get around this error and steal these from Windows Mobile instead, when you try and run the CETK tests you get a data abort in radiometricsdll.dll. How should we invoke the cellcore parts of CETK? Pev (Guest)[2010-3-30 12:21]: Hi all, Pev (Guest)[2010-3-30 12:21]: oops Pev (Guest)[2010-3-30 12:21]: :-D Pev (Guest)[2010-3-30 12:24]: Typically for SoC devices you name your hardware specific libraries in the form "SOCDIRNAME_LIBNAME". In our platform "OMAP35XX_TPS659XX_TI_V1" if you do this we cause the catalog parser to die... For example if we have a library "Musbfn_OMAP35XX_TPS659XX_TI_V1.dll" entering this in the catalogs pbcxml file in a <module> section causes the XML parser to fail with : Pev (Guest)[2010-3-30 12:25]: Q: Error 3 The 'urn:Microsoft.PlatformBuilder/Catalog:Module' element is        invalid - The value '012345678901234567890123456789.dll' is invalid         according to its datatype         'urn:Microsoft.PlatformBuilder/Catalog:CatalogFileName' - The actual         length is greater than the MaxLength value. GPM (Guest)[2010-3-30 12:25]: Q: Writable bitmap, is there an example of the syntax? Pev (Guest)[2010-3-30 12:25]: Q: Typically for SoC devices you name your hardware specific libraries in the form "SOCDIRNAME_LIBNAME". In our platform "OMAP35XX_TPS659XX_TI_V1" if you do this we cause the catalog parser to die... For example if we have a library "Musbfn_OMAP35XX_TPS659XX_TI_V1.dll" entering this in the catalogs pbcxml file in a <module> section causes the XML parser to fail with : Error 3 The 'urn:Microsoft.PlatformBuilder/Catalog:Module' element is        invalid - The value '012345678901234567890123456789.dll' is invalid         according to its datatype         'urn:Microsoft.PlatformBuilder/Catalog:CatalogFileName' - The actual         length is greater than the MaxLength value. Pev (Guest)[2010-3-30 12:25]: sorry, messed up submission there! GPM (Guest)[2010-3-30 12:26]: Q: I would like to get a handle to a Silverlight screen section, is that possiable? GPM (Guest)[2010-3-30 12:28]: Q: IXRVisualHost::GetHWND() exactly what I needed Thanks, PaulT (Guest)[2010-3-30 12:29]: GPM: You don't have to keep submitting the questions. The chat experts have an application that they're using to follow the chat and all Ask the Experts questions are logged. Jhony (Guest)[2010-3-30 12:29]: Q: I am getting this error only when I select the KdStub as the debugger in Target device connectivity. neo (Guest)[2010-3-30 12:30]: Q: ok. thanks for the book's link Pev (Guest)[2010-3-30 12:31]: Hm, did those two I submitted get picked up by anyone? neo (Guest)[2010-3-30 12:33]: Q: If I select Active KTIL, My OS doesn't boots. It says "loading NK.EXE at 0x<xxxxx> location" after that nothing comes in the debug log. PaulT (Guest)[2010-3-30 12:34]: Pev: PaulT (Guest)[2010-3-30 12:35]: Pev: I'm sure they did. The guys who are actually on the chat may not be experts in that part of things. That's usually the explanation when you don't get an answer in 10 minutes or so. Pev (Guest)[2010-3-30 12:36]: Ah, fair enough Susie (Guest)[2010-3-30 12:36]: My Outlook Express incoming mail is corrput. No ONE has been able to fix the problem, Dell or Norton. I have dial up I'm in a rural area Jhony (Guest)[2010-3-30 12:37]: Q: I have tried that and I am getting the same error. Pev (Guest)[2010-3-30 12:37]: Susie : Use Thunderbird instead :-D PaulT (Guest)[2010-3-30 12:37]: Susie: Sorry, but this chat is not about Windows, but Embedded (like what runs on a phone). Your best chance is to find a local expert or talk to your ISP. paolopat (Guest)[2010-3-30 12:37]: Q: what are the main differences between Object Store and RAM disk ? They are both in RAM...are there performance differences ? access differences ? Susie (Guest)[2010-3-30 12:38]: My computer knowlege is very limited, what is Thunderbird? Pev (Guest)[2010-3-30 12:38]: A different email client :-D neo (Guest)[2010-3-30 12:39]: Q: KITL: *** Device Name CEPC56059 *** WARN: KITL will run in polling mode VBridge:: built on [Jul 10 2009] time [10:20:14] VBridgeInit()...TX = [16384] bytes -- Rx = [16384] bytes Tx buffer [0xA1B84860] to [0xA1B88860]. Rx buffer [0xA1B88880] to [0xA1B8C880]. VBridge:: NK add MAC: [0-60-65-2-DA-FB] Connecting to Desktop KITL: Connected host IP: 1 Port: 1086 .. this is the output of the serial debug Susie (Guest)[2010-3-30 12:39]: Do I need to uninstall Outlook Express youngboyzie (Guest)[2010-3-30 12:39]: I need to start battery calibration for my new battery for my dell inspiron 1525 laptop and should be able to reach the BIOS screen by hitting f2 but this isnt working... help? Pev (Guest)[2010-3-30 12:39]: Nah, you can run it instead - you'll still need help from your ISP to configure it I expect Jhony (Guest)[2010-3-30 12:39]: Q: Both is happening via Ethernet. PaulT (Guest)[2010-3-30 12:40]: youngboyzie: You're off-topic. This is not a general chat for Windows and certainly not for Dell. You'll have to ask Dell how to get to setup; it's their machine. bill (Guest)[2010-3-30 12:41]: I lost spell check, how can i get et back neo (Guest)[2010-3-30 12:42]: Q: I didn't do that. I have to try. Jhony (Guest)[2010-3-30 12:43]: Q: Ok. I will do it then. bill (Guest)[2010-3-30 12:43]: Q: I lost spell check, how can i get it back PaulT (Guest)[2010-3-30 12:44]: bill: This isn't a general Windows chat. There are some Web forums that you might try. GarySwalling (Guest)[2010-3-30 12:45]: Q: Thanks, I found the Phone 7 presentation at http://live.visitmix.com/MIX10/Sessions/CL13 GPM (Guest)[2010-3-30 12:45]: Q: Is the Silverlight Animation "Spline" a BezierSpline? neo (Guest)[2010-3-30 12:46]: Q: ok. I'll do it. thanks Pev (Guest)[2010-3-30 12:46]: Whowever was asking about KITL connection : I've had this loads in the past. I think I started debugging last time by using wireshark to see what was happening on the network then setting up the OAL_ETHER and OAL_FUNC and OAL_VERBOSE as well as OAL_KITL flags to see what was actually happening in the driver.... Pev (Guest)[2010-3-30 12:47]: I'd generally make sure that you're testing though a 10baseT hub (instead of anything faster) and forcing Active KITL in polled mode too... neo (Guest)[2010-3-30 12:48]: Q: I disabled the firewall in my PC. Pev (Guest)[2010-3-30 12:50]: Q: I've got a platform (not developed by myself) where I2C bus support has to be provided through the OAL as the kernel needs to talk to devices such as the power management IC and gas gauge so a 'proper' I2C driver hanging off device manager isn't possible. This happens to be a polled driver, so obviously it hits the system hard when either under lots of traffic or an error condition occurs and the driver constantly polls. I originally thought that there was no straightforward way to make such code interrupt driven in the kernel (as it's a cludge) but I realised that that's exactly what ETHDBG drivers do. Is there any reason why I shouldn't have a go at implementing a similar mechanism for our kernel resident I2C driver? If not, are there any obvious pitfalls - I've not seen any other BSP's do this in the past... neo (Guest)[2010-3-30 12:51]: Q: I don't see a kitlcore.dll in my OS. is my debug image fails to load because of that? Pev (Guest)[2010-3-30 12:52]: Q: Hi masatos, I'm using Windows Embedded CE 6.0 with R3 and patched to feb 2010's QFE's (with it's associated CETK version) this is a machine with only CE 6.0 on (no conflicts with earlier CE or WM...) neo (Guest)[2010-3-30 12:54]: ok. Got it neo (Guest)[2010-3-30 12:54]: Q: ok. Got it Roundman (Guest)[2010-3-30 12:55]: Q: I am having trouble with my mouse, I have the microsoft wireless mobile mouse 3000, when I push the scroll button I am suppose to have autoscroll instead it shows other web pages,Can you help me out tell me what to do!!! Pev (Guest)[2010-3-30 12:55]: Hey neo, debugging kitl issues is really frustrating but dont lose heart :-) neo (Guest)[2010-3-30 12:55]: @ pev : u fixed the problem of KITL after that? neo (Guest)[2010-3-30 12:56]: I am getting the same error again and again. I even cleaned my environment and tried in a fresh PC. But didn't succeed yet Pev (Guest)[2010-3-30 12:56]: Well, eventually - my experiences probably won't help you as different platforms have different reasons for doing that neo (Guest)[2010-3-30 12:56]: I think so PaulT (Guest)[2010-3-30 12:58]: neo: Have you searched the old messages in microsoft.public.windowsce.platbuilder? It seems to me that there was a packet size situation where it was possible to have problems with KITL connections based on a setting on the PC. Google Groups, groups.google.com, Advanced Groups Search will allow you to search a single newsgroup or a set of newsgroups easily. GPM (Guest)[2010-3-30 12:58]: Q: Spline- bad link PaulT (Guest)[2010-3-30 12:58]: GPM: without the > at the end does it work? It seems to for me... neo (Guest)[2010-3-30 12:58]: But some times if i try to connect to the device again. The Image information is seen in the serial debug. what does that mean?Download BIN file information: ----------------------------------------------------- [0]: Base Address=0x220000 Length=0x18DAADC Received a broadcast message !CheckUDP: Not UDP (proto = 0x00000001) after this i am getting the old errors. PB debugger cannot initialize ... GPM (Guest)[2010-3-30 12:59]: Q: Sorry, got to tirm the ">" neo (Guest)[2010-3-30 12:59]: ok paul. I ll look into that. davbo-msft (Moderator)[2010-3-30 13:0]: Hello everyone, we are just about out of time. Thank you for joining us for our Windows Embedded CE 6.0 chat today! <http://www.Microsoft.com/Embedded>; A special thank you to the product group members for coming out. The transcript of today’s chat will be posted online as soon as possible, to <http://msdn.microsoft.com/en-us/chats>;. We’ll see you again for another chat next month. Please check <http://msdn.microsoft.com/en-us/chats>; for the list of upcoming chats. If you still have unanswered questions, let me suggest that you post them on one of our newsgroups on <http://msdn.microsoft.com/en-us/windowsembedded/ce/default.aspx> -Windows Embedded CE 6.0 R3 Now Available! <http://msdn.microsoft.com/windowsembedded/ce/dd630616.aspx>; neo (Guest)[2010-3-30 13:1]: Q: I am unable to use the target control in my development environment. any ideas? Pev (Guest)[2010-3-30 13:1]: Sure, if KITL isn't connected target control won't work as it runs over kitl... neo (Guest)[2010-3-30 13:1]: ok .thanks pev neo (Guest)[2010-3-30 13:2]: yes. sysgen_shell is set to 1 neo (Guest)[2010-3-30 13:2]: Q: yes. sysgen_shell is set to 1 Marcelovk (Guest)[2010-3-30 13:2]: Q: Is there any way to extract the default command lines of the tests in CETK? I want to have it running unconnected from the desktop.   Copyright © 2010 – Bruce Eitman All Rights Reserved

  Read the article

• getting SIGSEGV in std::_List_const_iterator<Exiv2::Exifdatum>::operator++ whilst using jni

  - by HJED

  Hi I'm using jni to access the exiv2 API in my Java project and I'm getting a SIGSEGV error in std::_List_const_iterator::operator++. I'm uncertain how to fix this error. I've tried using high -Xmx values as well as running on both jdk1.6.0 (server and cacao JVMs) and 1.7.0 (server JVM). gdb traceback: #0 0x00007fffa36f2363 in std::_List_const_iterator<Exiv2::Exifdatum>::operator++ (this=0x7ffff7fd3500) at /usr/include/c++/4.4/bits/stl_list.h:223 #1 0x00007fffa36f2310 in std::__distance<std::_List_const_iterator<Exiv2::Exifdatum> > (__first=..., __last=...) at /usr/include/c++/4.4/bits/stl_iterator_base_funcs.h:79 #2 0x00007fffa36f224d in std::distance<std::_List_const_iterator<Exiv2::Exifdatum> > (__first=..., __last=...) at /usr/include/c++/4.4/bits/stl_iterator_base_funcs.h:114 #3 0x00007fffa36f1f27 in std::list<Exiv2::Exifdatum, std::allocator<Exiv2::Exifdatum> >::size (this=0x7fffa4030910) at /usr/include/c++/4.4/bits/stl_list.h:805 #4 0x00007fffa36f1d50 in Exiv2::ExifData::count (this=0x7fffa4030910) at /usr/local/include/exiv2/exif.hpp:518 #5 0x00007fffa36f1d30 in Exiv2::ExifData::empty (this=0x7fffa4030910) at /usr/local/include/exiv2/exif.hpp:516 #6 0x00007fffa36f1763 in getVars (path=0x7fffa401d2f0 "/home/hjed/PC100001.JPG", env=0x6131c8, obj=0x7ffff7fd37a8) at src/main.cpp:146 #7 0x00007fffa36f19d8 in Java_photo_exiv2_Exiv2MetaDataStore_impl_1loadFromExiv (env=0x6131c8, obj=0x7ffff7fd37a8, path=0x7ffff7fd37a0, obj2=0x7ffff7fd3798) at src/main.cpp:160 #8 0x00007ffff21d9cc8 in ?? () #9 0x00000000fffffffe in ?? () #10 0x00007ffff7fd3740 in ?? () #11 0x0000000000613000 in ?? () #12 0x00007ffff7fd3738 in ?? () #13 0x00007fffaa1076e0 in ?? () #14 0x00007ffff7fd37a8 in ?? () #15 0x00007fffaa108d10 in ?? () #16 0x0000000000000000 in ?? () Java error: # A fatal error has been detected by the Java Runtime Environment: # # SIGSEGV (0xb) at pc=0x00007fac11223363, pid=11905, tid=140378349111040 # # JRE version: 6.0_20-b20 # Java VM: OpenJDK 64-Bit Server VM (19.0-b09 mixed mode linux-amd64 ) # Derivative: IcedTea6 1.9.2 # Distribution: Ubuntu 10.10, package 6b20-1.9.2-0ubuntu2 # Problematic frame: # C [libExiff2-binding.so+0x4363] _ZNSt20_List_const_iteratorIN5Exiv29ExifdatumEEppEv+0xf # # If you would like to submit a bug report, please include # instructions how to reproduce the bug and visit: # https://bugs.launchpad.net/ubuntu/+source/openjdk-6/ # The crash happened outside the Java Virtual Machine in native code. # See problematic frame for where to report the bug. # --------------- T H R E A D --------------- Current thread (0x0000000000dbf000): JavaThread "main" [_thread_in_native, id=11909, stack(0x00007fac61920000,0x00007fac61a21000)] siginfo:si_signo=SIGSEGV: si_errno=0, si_code=128 (), si_addr=0x0000000000000000 Registers: ... Register to memory mapping: RAX=0x6c8948f0245c8948 0x6c8948f0245c8948 is pointing to unknown location RBX=0x00007fac0c042c00 0x00007fac0c042c00 is pointing to unknown location RCX=0x0000000000000000 0x0000000000000000 is pointing to unknown location RDX=0x6c8948f0245c8948 0x6c8948f0245c8948 is pointing to unknown location RSP=0x00007fac61a1f4e0 0x00007fac61a1f4e0 is pointing into the stack for thread: 0x0000000000dbf000 "main" prio=10 tid=0x0000000000dbf000 nid=0x2e85 runnable [0x00007fac61a1f000] java.lang.Thread.State: RUNNABLE RBP=0x00007fac61a1f4e0 0x00007fac61a1f4e0 is pointing into the stack for thread: 0x0000000000dbf000 "main" prio=10 tid=0x0000000000dbf000 nid=0x2e85 runnable [0x00007fac61a1f000] java.lang.Thread.State: RUNNABLE RSI=0x00007fac61a1f4f0 0x00007fac61a1f4f0 is pointing into the stack for thread: 0x0000000000dbf000 "main" prio=10 tid=0x0000000000dbf000 nid=0x2e85 runnable [0x00007fac61a1f000] java.lang.Thread.State: RUNNABLE RDI=0x00007fac61a1f500 0x00007fac61a1f500 is pointing into the stack for thread: 0x0000000000dbf000 "main" prio=10 tid=0x0000000000dbf000 nid=0x2e85 runnable [0x00007fac61a1f000] java.lang.Thread.State: RUNNABLE R8 =0x00007fac0c054630 0x00007fac0c054630 is pointing to unknown location R9 =0x00007fac61a1f358 0x00007fac61a1f358 is pointing into the stack for thread: 0x0000000000dbf000 "main" prio=10 tid=0x0000000000dbf000 nid=0x2e85 runnable [0x00007fac61a1f000] java.lang.Thread.State: RUNNABLE R10=0x00007fac61a1f270 0x00007fac61a1f270 is pointing into the stack for thread: 0x0000000000dbf000 "main" prio=10 tid=0x0000000000dbf000 nid=0x2e85 runnable [0x00007fac61a1f000] java.lang.Thread.State: RUNNABLE R11=0x00007fac11223354 0x00007fac11223354: _ZNSt20_List_const_iteratorIN5Exiv29ExifdatumEEppEv+0 in /home/hjed/libExiff2-binding.so at 0x00007fac1121f000 R12=0x0000000000dbf000 "main" prio=10 tid=0x0000000000dbf000 nid=0x2e85 runnable [0x00007fac61a1f000] java.lang.Thread.State: RUNNABLE R13=0x00007fac13ad1be8 {method} - klass: {other class} R14=0x00007fac61a1f7a8 0x00007fac61a1f7a8 is pointing into the stack for thread: 0x0000000000dbf000 "main" prio=10 tid=0x0000000000dbf000 nid=0x2e85 runnable [0x00007fac61a1f000] java.lang.Thread.State: RUNNABLE R15=0x0000000000dbf000 "main" prio=10 tid=0x0000000000dbf000 nid=0x2e85 runnable [0x00007fac61a1f000] java.lang.Thread.State: RUNNABLE Top of Stack: (sp=0x00007fac61a1f4e0) ... Instructions: (pc=0x00007fac11223363) ... Stack: [0x00007fac61920000,0x00007fac61a21000], sp=0x00007fac61a1f4e0, free space=1021k Native frames: (J=compiled Java code, j=interpreted, Vv=VM code, C=native code) C [libExiff2-binding.so+0x4363] _ZNSt20_List_const_iteratorIN5Exiv29ExifdatumEEppEv+0xf C [libExiff2-binding.so+0x4310] _ZSt10__distanceISt20_List_const_iteratorIN5Exiv29ExifdatumEEENSt15iterator_traitsIT_E15difference_typeES5_S5_St18input_iterator_tag+0x26 C [libExiff2-binding.so+0x424d] _ZSt8distanceISt20_List_const_iteratorIN5Exiv29ExifdatumEEENSt15iterator_traitsIT_E15difference_typeES5_S5_+0x36 C [libExiff2-binding.so+0x3f27] _ZNKSt4listIN5Exiv29ExifdatumESaIS1_EE4sizeEv+0x33 C [libExiff2-binding.so+0x3d50] _ZNK5Exiv28ExifData5countEv+0x18 C [libExiff2-binding.so+0x3d30] _ZNK5Exiv28ExifData5emptyEv+0x18 C [libExiff2-binding.so+0x3763] _Z7getVarsPKcP7JNIEnv_P8_jobject+0x3e3 C [libExiff2-binding.so+0x39d8] Java_photo_exiv2_Exiv2MetaDataStore_impl_1loadFromExiv+0x4b j photo.exiv2.Exiv2MetaDataStore.impl_loadFromExiv(Ljava/lang/String;Lphoto/exiv2/Exiv2MetaDataStore;)V+0 j photo.exiv2.Exiv2MetaDataStore.loadFromExiv2()V+9 j photo.exiv2.Exiv2MetaDataStore.loadData()V+1 j photo.exiv2.Exiv2MetaDataStore.<init>(Lphoto/ImageFile;)V+10 j photo.ImageFile.<init>(Ljava/lang/String;)V+11 j test.Main.main([Ljava/lang/String;)V+67 v ~StubRoutines::call_stub V [libjvm.so+0x428698] V [libjvm.so+0x4275c8] V [libjvm.so+0x432943] V [libjvm.so+0x447f91] C [java+0x3495] JavaMain+0xd75 Java frames: (J=compiled Java code, j=interpreted, Vv=VM code) j photo.exiv2.Exiv2MetaDataStore.impl_loadFromExiv(Ljava/lang/String;Lphoto/exiv2/Exiv2MetaDataStore;)V+0 j photo.exiv2.Exiv2MetaDataStore.loadFromExiv2()V+9 j photo.exiv2.Exiv2MetaDataStore.loadData()V+1 j photo.exiv2.Exiv2MetaDataStore.<init>(Lphoto/ImageFile;)V+10 j photo.ImageFile.<init>(Ljava/lang/String;)V+11 j test.Main.main([Ljava/lang/String;)V+67 v ~StubRoutines::call_stub --------------- P R O C E S S --------------- Java Threads: ( => current thread ) 0x00007fac0c028000 JavaThread "Low Memory Detector" daemon [_thread_blocked, id=11924, stack(0x00007fac11532000,0x00007fac11633000)] 0x00007fac0c025800 JavaThread "CompilerThread1" daemon [_thread_blocked, id=11923, stack(0x00007fac11633000,0x00007fac11734000)] 0x00007fac0c022000 JavaThread "CompilerThread0" daemon [_thread_blocked, id=11922, stack(0x00007fac11734000,0x00007fac11835000)] 0x00007fac0c01f800 JavaThread "Signal Dispatcher" daemon [_thread_blocked, id=11921, stack(0x00007fac11835000,0x00007fac11936000)] 0x00007fac0c001000 JavaThread "Finalizer" daemon [_thread_blocked, id=11920, stack(0x00007fac11e2d000,0x00007fac11f2e000)] 0x0000000000e36000 JavaThread "Reference Handler" daemon [_thread_blocked, id=11919, stack(0x00007fac11f2e000,0x00007fac1202f000)] =>0x0000000000dbf000 JavaThread "main" [_thread_in_native, id=11909, stack(0x00007fac61920000,0x00007fac61a21000)] Other Threads: 0x0000000000e2f800 VMThread [stack: 0x00007fac1202f000,0x00007fac12130000] [id=11918] 0x00007fac0c02b000 WatcherThread [stack: 0x00007fac11431000,0x00007fac11532000] [id=11925] ... Heap PSYoungGen total 18432K, used 632K [0x00007fac47210000, 0x00007fac486a0000, 0x00007fac5bc10000) eden space 15808K, 4% used [0x00007fac47210000,0x00007fac472ae188,0x00007fac48180000) from space 2624K, 0% used [0x00007fac48410000,0x00007fac48410000,0x00007fac486a0000) to space 2624K, 0% used [0x00007fac48180000,0x00007fac48180000,0x00007fac48410000) PSOldGen total 42240K, used 0K [0x00007fac1de10000, 0x00007fac20750000, 0x00007fac47210000) object space 42240K, 0% used [0x00007fac1de10000,0x00007fac1de10000,0x00007fac20750000) PSPermGen total 21248K, used 2831K [0x00007fac13810000, 0x00007fac14cd0000, 0x00007fac1de10000) object space 21248K, 13% used [0x00007fac13810000,0x00007fac13ad3d80,0x00007fac14cd0000) Dynamic libraries: ... VM Arguments: jvm_args: -Dfile.encoding=UTF-8 java_command: test.Main Launcher Type: SUN_STANDARD Environment Variables: PATH=/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games USERNAME=hjed LD_LIBRARY_PATH=/usr/lib/jvm/java-6-openjdk/jre/lib/amd64/server:/usr/lib/jvm/java-6-openjdk/jre/lib/amd64:/usr/lib/jvm/java-6-openjdk/jre/../lib/amd64 SHELL=/bin/bash DISPLAY=:0.0 Signal Handlers: ... --------------- S Y S T E M --------------- OS:Ubuntu 10.10 (maverick) uname:Linux 2.6.35-24-generic #42-Ubuntu SMP Thu Dec 2 02:41:37 UTC 2010 x86_64 libc:glibc 2.12.1 NPTL 2.12.1 rlimit: STACK 8192k, CORE 0k, NPROC infinity, NOFILE 1024, AS infinity load average:0.27 0.31 0.30 /proc/meminfo: MemTotal: 4048200 kB MemFree: 106552 kB Buffers: 838212 kB Cached: 1172496 kB SwapCached: 0 kB Active: 1801316 kB Inactive: 1774880 kB Active(anon): 1224708 kB Inactive(anon): 355012 kB Active(file): 576608 kB Inactive(file): 1419868 kB Unevictable: 64 kB Mlocked: 64 kB SwapTotal: 7065596 kB SwapFree: 7065596 kB Dirty: 20 kB Writeback: 0 kB AnonPages: 1565608 kB Mapped: 213424 kB Shmem: 14216 kB Slab: 164812 kB SReclaimable: 102576 kB SUnreclaim: 62236 kB KernelStack: 4784 kB PageTables: 44908 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 9089696 kB Committed_AS: 3676872 kB VmallocTotal: 34359738367 kB VmallocUsed: 332952 kB VmallocChunk: 34359397884 kB HardwareCorrupted: 0 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB DirectMap4k: 48704 kB DirectMap2M: 4136960 kB CPU:total 8 (4 cores per cpu, 2 threads per core) family 6 model 26 stepping 5, cmov, cx8, fxsr, mmx, sse, sse2, sse3, ssse3, sse4.1, sse4.2, popcnt, ht Memory: 4k page, physical 4048200k(106552k free), swap 7065596k(7065596k free) vm_info: OpenJDK 64-Bit Server VM (19.0-b09) for linux-amd64 JRE (1.6.0_20-b20), built on Dec 10 2010 19:45:55 by "buildd" with gcc 4.4.5 main.cpp: jobject toJava(std::auto_ptr<Exiv2::Value> v, const char * type, JNIEnv * env) { jclass stringClass; jmethodID cid; jobject result; stringClass = env->FindClass("photo/exiv2/Value"); cid = env->GetMethodID(stringClass, "<init>", "(Ljava/lang/String;Ljava/lang/Object;)V"); jvalue val; if ((strcmp(type, "String") == 0) || (strcmp(type, "String") == 0)) { val.l = env->NewStringUTF(v->toString().c_str()); } else if (strcmp(type, "Short") == 0) { val.s = v->toLong(0); } else if (strcmp(type, "Long") == 0) { val.j = v->toLong(0); } result = env->NewObject(stringClass, cid, env->NewStringUTF(v->toString().c_str()), val); return result; } void inLoop(std::auto_ptr<MetadataContainer> md, JNIEnv * env, jmethodID mid, jobject obj) { jvalue values[2]; const char* key = md->key().c_str(); values[0].l = env->NewStringUTF(key); /** md->value().toString().c_str(); const char* value = md->typeName(); values[1].l = env->NewStringUTF(value); TODO: do type conversions */ //std::cout << md->typeName() << std::endl; /** const char* type = md->value().toString().c_str(); values[1].l = env->NewStringUTF(type);*/ values[1].l = toJava(md->getValue(), md->typeName(), env); env->CallVoidMethodA(obj, mid, values); } void getVars(const char* path, JNIEnv * env, jobject obj) { //Load image Exiv2::Image::AutoPtr image = Exiv2::ImageFactory::open(path); assert(image.get() != 0); image->readMetadata(); //load method jclass cls = env->GetObjectClass(obj); jmethodID mid = env->GetMethodID(cls, "exiv2_reciveElement", "(Ljava/lang/String;Lphoto/exiv2/Value;)V"); //Load IPTC data /**loadIPTC(image, path, env, obj, mid); loadEXIF(image, path, env, obj, mid);*/ Exiv2::IptcData &iptcData = image->iptcData(); if (mid != NULL) { //is there any IPTC data AND check that method exists if (iptcData.empty()) { std::string error(path); error += ": failed loading IPTC data, there may not be any data"; } else { Exiv2::IptcData::iterator end = iptcData.end(); for (Exiv2::IptcData::iterator md = iptcData.begin(); md != end; ++md) { std::auto_ptr<MetadataContainer> meta(new MetadataContainer(md)); inLoop(meta, env, mid, obj); } } Exiv2::ExifData &exifData = image->exifData(); //is there any Exif data AND check that method exists if (exifData.empty()) { //error occurs here (main.cpp:146) std::string error(path); error += ": failed loading Exif data, there may not be any data"; } else { Exiv2::ExifData::iterator end = exifData.end(); for (Exiv2::ExifData::iterator md = exifData.begin(); md != end; ++md) { std::auto_ptr<MetadataContainer> meta(new MetadataContainer(md)); inLoop(meta, env, mid, obj); } } } else { std::string error(path); error += ": failed to load method"; } } JNIEXPORT void JNICALL Java_photo_exiv2_Exiv2MetaDataStore_impl_1loadFromExiv(JNIEnv * env, jobject obj, jstring path, jobject obj2) { const char* path2 = env->GetStringUTFChars(path, NULL); getVars(path2, env, obj); env->ReleaseStringUTFChars(path, path2); } Thanks for any help, HJED EDIT This is the output when runing the jvm with the -cacao option: run: null:/usr/local/lib Error: Directory Olympus2 with 1536 entries considered invalid; not read. LOG: [0x00007ff005376700] We received a SIGSEGV and tried to handle it, but we were LOG: [0x00007ff005376700] unable to find a Java method at: LOG: [0x00007ff005376700] LOG: [0x00007ff005376700] PC=0x00007feffe4ee67d LOG: [0x00007ff005376700] LOG: [0x00007ff005376700] Dumping the current stacktrace: at photo.exiv2.Exiv2MetaDataStore.impl_loadFromExiv(Ljava/lang/String;Lphoto/exiv2/Exiv2MetaDataStore;)V(Native Method) at photo.exiv2.Exiv2MetaDataStore.loadFromExiv2()V(Exiv2MetaDataStore.java:38) at photo.exiv2.Exiv2MetaDataStore.loadData()V(Exiv2MetaDataStore.java:29) at photo.exiv2.MetaDataStore.<init>(Lphoto/ImageFile;)V(MetaDataStore.java:33) at photo.exiv2.Exiv2MetaDataStore.<init>(Lphoto/ImageFile;)V(Exiv2MetaDataStore.java:20) at photo.ImageFile.<init>(Ljava/lang/String;)V(ImageFile.java:22) at test.Main.main([Ljava/lang/String;)V(Main.java:28) LOG: [0x00007ff005376700] vm_abort: WARNING, port me to C++ and use os::abort() instead. LOG: [0x00007ff005376700] Exiting... LOG: [0x00007ff005376700] Backtrace (15 stack frames): LOG: [0x00007ff005376700] /usr/lib/jvm/java-6-openjdk/jre/lib/amd64/cacao/libjvm.so(+0x4ff54) [0x7ff004306f54] LOG: [0x00007ff005376700] /usr/lib/jvm/java-6-openjdk/jre/lib/amd64/cacao/libjvm.so(+0x5ac01) [0x7ff004311c01] LOG: [0x00007ff005376700] /usr/lib/jvm/java-6-openjdk/jre/lib/amd64/cacao/libjvm.so(+0x66e9a) [0x7ff00431de9a] LOG: [0x00007ff005376700] /usr/lib/jvm/java-6-openjdk/jre/lib/amd64/cacao/libjvm.so(+0x76408) [0x7ff00432d408] LOG: [0x00007ff005376700] /usr/lib/jvm/java-6-openjdk/jre/lib/amd64/cacao/libjvm.so(+0x79a4c) [0x7ff004330a4c] LOG: [0x00007ff005376700] /lib/libpthread.so.0(+0xfb40) [0x7ff004d53b40] LOG: [0x00007ff005376700] /home/hjed/libExiff2-binding.so(_ZNSt20_List_const_iteratorIN5Exiv29ExifdatumEEppEv+0xf) [0x7feffe4ee67d] LOG: [0x00007ff005376700] /home/hjed/libExiff2-binding.so(_ZSt10__distanceISt20_List_const_iteratorIN5Exiv29ExifdatumEEENSt15iterator_traitsIT_E15difference_typeES5_S5_St18input_iterator_tag+0x26) [0x7feffe4ee62a] LOG: [0x00007ff005376700] /home/hjed/libExiff2-binding.so(_ZSt8distanceISt20_List_const_iteratorIN5Exiv29ExifdatumEEENSt15iterator_traitsIT_E15difference_typeES5_S5_+0x36) [0x7feffe4ee567] LOG: [0x00007ff005376700] /home/hjed/libExiff2-binding.so(_ZNKSt4listIN5Exiv29ExifdatumESaIS1_EE4sizeEv+0x33) [0x7feffe4ee22b] LOG: [0x00007ff005376700] /home/hjed/libExiff2-binding.so(_ZNK5Exiv28ExifData5countEv+0x18) [0x7feffe4ee054] LOG: [0x00007ff005376700] /home/hjed/libExiff2-binding.so(_ZNK5Exiv28ExifData5emptyEv+0x18) [0x7feffe4ee034] LOG: [0x00007ff005376700] /home/hjed/libExiff2-binding.so(_Z7getVarsPKcP7JNIEnv_P8_jobject+0x3d7) [0x7feffe4ed947] LOG: [0x00007ff005376700] /home/hjed/libExiff2-binding.so(Java_photo_exiv2_Exiv2MetaDataStore_impl_1loadFromExiv+0x4b) [0x7feffe4edcdc] LOG: [0x00007ff005376700] [0x7feffe701ccd] Java Result: 134 BUILD SUCCESSFUL (total time: 0 seconds)

  Read the article

• Linq 2 SQL using base class and WCF

  - by Gena Verdel

  Hi all. I have the following problem: I'm using L2S for generating entity classes. All these classes share the same property ID which is autonumber. So I figured to put this property to base class and extend all entity classes from the base one. In order to be able to read the value I'm using the override modifier on this property in each and every entity class. Up to now it's live and kicking. Then I decided to introduce another tier - services using WCF approach. I've modified the Serialization mode to Unidirectional (and added the IsReference=true attribute to enable two directions), also added [DataContract] attribute to the BaseObject class. WCF is able to transport the whole object but one property , which is ID. Applying [DataMember] attribute on ID property at the base class resulted in nothing. Am I missing something? Is what I'm trying to achieve possible at all? [DataContract()] abstract public class BaseObject : IIccObject public virtual long ID { get; set; } [Table(Name="dbo.Blocks")] [DataContract(IsReference=true)] public partial class Block : INotifyPropertyChanging, INotifyPropertyChanged { private static PropertyChangingEventArgs emptyChangingEventArgs = new PropertyChangingEventArgs(String.Empty); private long _ID; private int _StatusID; private string _Name; private bool _IsWithControlPoints; private long _DivisionID; private string _SHAPE; private EntitySet<BlockByWorkstation> _BlockByWorkstations; private EntitySet<PlanningPointAppropriation> _PlanningPointAppropriations; private EntitySet<Neighbor> _Neighbors; private EntitySet<Neighbor> _Neighbors1; private EntitySet<Task> _Tasks; private EntitySet<PlanningPointByBlock> _PlanningPointByBlocks; private EntityRef<Division> _Division; private bool serializing; #region Extensibility Method Definitions partial void OnLoaded(); partial void OnValidate(System.Data.Linq.ChangeAction action); partial void OnCreated(); partial void OnIDChanging(long value); partial void OnIDChanged(); partial void OnStatusIDChanging(int value); partial void OnStatusIDChanged(); partial void OnNameChanging(string value); partial void OnNameChanged(); partial void OnIsWithControlPointsChanging(bool value); partial void OnIsWithControlPointsChanged(); partial void OnDivisionIDChanging(long value); partial void OnDivisionIDChanged(); partial void OnSHAPEChanging(string value); partial void OnSHAPEChanged(); #endregion public Block() { this.Initialize(); } [Column(Storage="_ID", AutoSync=AutoSync.OnInsert, DbType="BigInt NOT NULL IDENTITY", IsPrimaryKey=true, IsDbGenerated=true)] [DataMember(Order=1)] public override long ID { get { return this._ID; } set { if ((this._ID != value)) { this.OnIDChanging(value); this.SendPropertyChanging(); this._ID = value; this.SendPropertyChanged("ID"); this.OnIDChanged(); } } } [Column(Storage="_StatusID", DbType="Int NOT NULL")] [DataMember(Order=2)] public int StatusID { get { return this._StatusID; } set { if ((this._StatusID != value)) { this.OnStatusIDChanging(value); this.SendPropertyChanging(); this._StatusID = value; this.SendPropertyChanged("StatusID"); this.OnStatusIDChanged(); } } } [Column(Storage="_Name", DbType="NVarChar(255)")] [DataMember(Order=3)] public string Name { get { return this._Name; } set { if ((this._Name != value)) { this.OnNameChanging(value); this.SendPropertyChanging(); this._Name = value; this.SendPropertyChanged("Name"); this.OnNameChanged(); } } } [Column(Storage="_IsWithControlPoints", DbType="Bit NOT NULL")] [DataMember(Order=4)] public bool IsWithControlPoints { get { return this._IsWithControlPoints; } set { if ((this._IsWithControlPoints != value)) { this.OnIsWithControlPointsChanging(value); this.SendPropertyChanging(); this._IsWithControlPoints = value; this.SendPropertyChanged("IsWithControlPoints"); this.OnIsWithControlPointsChanged(); } } } [Column(Storage="_DivisionID", DbType="BigInt NOT NULL")] [DataMember(Order=5)] public long DivisionID { get { return this._DivisionID; } set { if ((this._DivisionID != value)) { if (this._Division.HasLoadedOrAssignedValue) { throw new System.Data.Linq.ForeignKeyReferenceAlreadyHasValueException(); } this.OnDivisionIDChanging(value); this.SendPropertyChanging(); this._DivisionID = value; this.SendPropertyChanged("DivisionID"); this.OnDivisionIDChanged(); } } } [Column(Storage="_SHAPE", DbType="Text", UpdateCheck=UpdateCheck.Never)] [DataMember(Order=6)] public string SHAPE { get { return this._SHAPE; } set { if ((this._SHAPE != value)) { this.OnSHAPEChanging(value); this.SendPropertyChanging(); this._SHAPE = value; this.SendPropertyChanged("SHAPE"); this.OnSHAPEChanged(); } } } [Association(Name="Block_BlockByWorkstation", Storage="_BlockByWorkstations", ThisKey="ID", OtherKey="BlockID")] [DataMember(Order=7, EmitDefaultValue=false)] public EntitySet<BlockByWorkstation> BlockByWorkstations { get { if ((this.serializing && (this._BlockByWorkstations.HasLoadedOrAssignedValues == false))) { return null; } return this._BlockByWorkstations; } set { this._BlockByWorkstations.Assign(value); } } [Association(Name="Block_PlanningPointAppropriation", Storage="_PlanningPointAppropriations", ThisKey="ID", OtherKey="MasterBlockID")] [DataMember(Order=8, EmitDefaultValue=false)] public EntitySet<PlanningPointAppropriation> PlanningPointAppropriations { get { if ((this.serializing && (this._PlanningPointAppropriations.HasLoadedOrAssignedValues == false))) { return null; } return this._PlanningPointAppropriations; } set { this._PlanningPointAppropriations.Assign(value); } } [Association(Name="Block_Neighbor", Storage="_Neighbors", ThisKey="ID", OtherKey="FirstBlockID")] [DataMember(Order=9, EmitDefaultValue=false)] public EntitySet<Neighbor> Neighbors { get { if ((this.serializing && (this._Neighbors.HasLoadedOrAssignedValues == false))) { return null; } return this._Neighbors; } set { this._Neighbors.Assign(value); } } [Association(Name="Block_Neighbor1", Storage="_Neighbors1", ThisKey="ID", OtherKey="SecondBlockID")] [DataMember(Order=10, EmitDefaultValue=false)] public EntitySet<Neighbor> Neighbors1 { get { if ((this.serializing && (this._Neighbors1.HasLoadedOrAssignedValues == false))) { return null; } return this._Neighbors1; } set { this._Neighbors1.Assign(value); } } [Association(Name="Block_Task", Storage="_Tasks", ThisKey="ID", OtherKey="BlockID")] [DataMember(Order=11, EmitDefaultValue=false)] public EntitySet<Task> Tasks { get { if ((this.serializing && (this._Tasks.HasLoadedOrAssignedValues == false))) { return null; } return this._Tasks; } set { this._Tasks.Assign(value); } } [Association(Name="Block_PlanningPointByBlock", Storage="_PlanningPointByBlocks", ThisKey="ID", OtherKey="BlockID")] [DataMember(Order=12, EmitDefaultValue=false)] public EntitySet<PlanningPointByBlock> PlanningPointByBlocks { get { if ((this.serializing && (this._PlanningPointByBlocks.HasLoadedOrAssignedValues == false))) { return null; } return this._PlanningPointByBlocks; } set { this._PlanningPointByBlocks.Assign(value); } } [Association(Name="Division_Block", Storage="_Division", ThisKey="DivisionID", OtherKey="ID", IsForeignKey=true, DeleteOnNull=true, DeleteRule="CASCADE")] public Division Division { get { return this._Division.Entity; } set { Division previousValue = this._Division.Entity; if (((previousValue != value) || (this._Division.HasLoadedOrAssignedValue == false))) { this.SendPropertyChanging(); if ((previousValue != null)) { this._Division.Entity = null; previousValue.Blocks.Remove(this); } this._Division.Entity = value; if ((value != null)) { value.Blocks.Add(this); this._DivisionID = value.ID; } else { this._DivisionID = default(long); } this.SendPropertyChanged("Division"); } } } public event PropertyChangingEventHandler PropertyChanging; public event PropertyChangedEventHandler PropertyChanged; protected virtual void SendPropertyChanging() { if ((this.PropertyChanging != null)) { this.PropertyChanging(this, emptyChangingEventArgs); } } protected virtual void SendPropertyChanged(String propertyName) { if ((this.PropertyChanged != null)) { this.PropertyChanged(this, new PropertyChangedEventArgs(propertyName)); } } private void attach_BlockByWorkstations(BlockByWorkstation entity) { this.SendPropertyChanging(); entity.Block = this; } private void detach_BlockByWorkstations(BlockByWorkstation entity) { this.SendPropertyChanging(); entity.Block = null; } private void attach_PlanningPointAppropriations(PlanningPointAppropriation entity) { this.SendPropertyChanging(); entity.Block = this; } private void detach_PlanningPointAppropriations(PlanningPointAppropriation entity) { this.SendPropertyChanging(); entity.Block = null; } private void attach_Neighbors(Neighbor entity) { this.SendPropertyChanging(); entity.FirstBlock = this; } private void detach_Neighbors(Neighbor entity) { this.SendPropertyChanging(); entity.FirstBlock = null; } private void attach_Neighbors1(Neighbor entity) { this.SendPropertyChanging(); entity.SecondBlock = this; } private void detach_Neighbors1(Neighbor entity) { this.SendPropertyChanging(); entity.SecondBlock = null; } private void attach_Tasks(Task entity) { this.SendPropertyChanging(); entity.Block = this; } private void detach_Tasks(Task entity) { this.SendPropertyChanging(); entity.Block = null; } private void attach_PlanningPointByBlocks(PlanningPointByBlock entity) { this.SendPropertyChanging(); entity.Block = this; } private void detach_PlanningPointByBlocks(PlanningPointByBlock entity) { this.SendPropertyChanging(); entity.Block = null; } private void Initialize() { this._BlockByWorkstations = new EntitySet<BlockByWorkstation>(new Action<BlockByWorkstation>(this.attach_BlockByWorkstations), new Action<BlockByWorkstation>(this.detach_BlockByWorkstations)); this._PlanningPointAppropriations = new EntitySet<PlanningPointAppropriation>(new Action<PlanningPointAppropriation>(this.attach_PlanningPointAppropriations), new Action<PlanningPointAppropriation>(this.detach_PlanningPointAppropriations)); this._Neighbors = new EntitySet<Neighbor>(new Action<Neighbor>(this.attach_Neighbors), new Action<Neighbor>(this.detach_Neighbors)); this._Neighbors1 = new EntitySet<Neighbor>(new Action<Neighbor>(this.attach_Neighbors1), new Action<Neighbor>(this.detach_Neighbors1)); this._Tasks = new EntitySet<Task>(new Action<Task>(this.attach_Tasks), new Action<Task>(this.detach_Tasks)); this._PlanningPointByBlocks = new EntitySet<PlanningPointByBlock>(new Action<PlanningPointByBlock>(this.attach_PlanningPointByBlocks), new Action<PlanningPointByBlock>(this.detach_PlanningPointByBlocks)); this._Division = default(EntityRef<Division>); OnCreated(); } [OnDeserializing()] [System.ComponentModel.EditorBrowsableAttribute(EditorBrowsableState.Never)] public void OnDeserializing(StreamingContext context) { this.Initialize(); } [OnSerializing()] [System.ComponentModel.EditorBrowsableAttribute(EditorBrowsableState.Never)] public void OnSerializing(StreamingContext context) { this.serializing = true; } [OnSerialized()] [System.ComponentModel.EditorBrowsableAttribute(EditorBrowsableState.Never)] public void OnSerialized(StreamingContext context) { this.serializing = false; } }

  Read the article

• "CB Monitor Windows" proccess blocks XP shutdown

  - by Shiki

  I've got a home server. Simple, low-power-consumption Intel Atom based PC built by me. It runs XP since Win7 was an overkill for this poor thing. Everything was OK, always used Avast! antivirus + Spybot. However, it stopped shutting down after a while. Few days ago I noticed a "CB Monitor Windows" proccess is blocking this (didn't quit from rdp after sending the shutdown command). What is this proccess? How can I disable/remove it? Tried Malwarebytes, found ONE malware, removed it, did a reboot, no change. Avast is up-to-date, Spybot is the same. What could I do?

  Read the article

• Sony DCR-TRV14E Video Camera Drivers for Windows 7 64-bit

  - by A_M

  Hi, I've just built a new PC and installed 64-bit Windows 7 RC. I'm trying to get my video camera to work with it. It's a Sony DCR-TRV14E (PAL). When using Firewire, Windows detects the camera but does not display the "autorun" popup dialog with the various options of what to do with the files on the camera. However, the camera does appear in the devices page of Control Panel. When using USB, Windows fails when trying to install drivers. I can't find any drivers on the Sony site which say they'll be compatible with Windows 7 (or 64-bit). Has anyone had any luck with this Sony camera (or similar ones?). Thanks.

  Read the article

• s3fs Input/output error

  - by shadow_of__soul

  i'm trying to set up a backup system with s3fs and the amazon s3 service. i followed this 2 guides: http://qugstart.com/blog/linux/how-to-mount-an-amazon-s3-bucket-as-virtual-drive-on-centos-5-2/ http://blog.eberly.org/2008/10/27/how-i-automated-my-backups-to-amazon-s3-using-rsync/ anyway making a tail to the /var/log/messages i get: Aug 28 13:37:46 server s3fs:###response=403 i already tried creating the authentication file on /etc/passwd-s3fs and setting there the access and private key, passing it trough the command line, i checked several times the credentials and i used it with s3fox, and is working. i also have set the time of the machine (with the date command) to be the same as the amazon S3 servers (i got the time of the S3 server uploading a file with the file manager) not only rsync don't work, commands like ls or cp in the /mnt/s3 didn't work also. any help of how i can solve/debug this? Regards, Shadow.

  Read the article

• Hyper-V and Hyper-threading: On or off?

  - by CapBBeard

  Hey all, With the new Xeon CPUs supporting Hyper-threading, what is the current wisdom with regard to using it (or not) on a Hyper-V host machine? I was originally under the impression that turning it on in a virtual host environment could be detrimental as the 'extra' CPUs were not true cores. However I've also read (unconfirmed) comments along the lines of MS doing some hard work to get Hyper-V running well in a Hyper-threading environment. Does anyone have any solid information or experience in this regard? Cheers!

  Read the article

• Severe errors in solr configuration: Error loading class 'solr.TrieDateField'

  - by James Lawruk

  Installed Solr on my Windows XP PC. Tomcat seems to be working fine. Cannot get Solr to work. I noticed the TrieDateField is declared in a file called schema.xml in the SolrHome directory. Any thoughts? The Url http://localhost:8080/solr/ returns: HTTP Status 500 - Severe errors in solr configuration. Check your log files for more detailed information on what may be wrong. If you want solr to continue after configuration errors, change: false in null ------------------------------------------------------------- org.apache.solr.common.SolrException: Unknown fieldtype 'date' specified on field updated Here is an excerpt from the catalina log file: SEVERE: org.apache.solr.common.SolrException: Error loading class 'solr.TrieDateField' at org.apache.solr.core.SolrResourceLoader.findClass(SolrResourceLoader.java:273) Caused by: java.lang.ClassNotFoundException: solr.TrieDateField

  Read the article

• Can not enable Windows SmartScreen. Says: "this setting is managed by your system administrator"

  - by Afshin Gh

  I can not enable my Windows SmartScreen on Windows 8.1 My PC is not joined to any domain. I'm not talking about SmartScreen feature available in IE but the feature that is available in File Explorer. Control Panel Action Center Change Windows SmartScreen settings I searched in group policy but couldn't find anything that is preventing me from enabling it. Update 1: My user is a member of administrators group. Other things work fine. When I try to change something that needs administrative permission, UAC window appears, but nothing here.

  Read the article

• Sonicwall VPN, Domain Controller Issues

  - by durilai

  I am trying to get the domain logon script to execute when I connect to VPN. I have a SonicWall 4060PRO, with the SonicOS Enhanced 4.2.0.0-10e. The VPN connects successfully, but the script does not execute. I am posting the log below, but I see two issues. The first is the inability to connect to domain. 2009/12/18 19:49:53:457 Information XXX.XXX.XXX.XXX NetGetDCName failed: Could not find domain controller for this domain. The second is the failure of the script. 2009/12/18 19:49:53:466 Warning XXX.XXX.XXX.XXX Failed to execute script file \DT-WIN7netlogondomain.bat, Last Error: The network name cannot be found.. I assume the second issue is caused because of the first, also on the second issue it seems to be trying to get the logon script from my local PC, not the server. Finally, the DC can be pinged and reached by its computer name once the VPN is connected. The shares that the script is tring to map can be mapped manually. Any help is appreciated. 2009/12/18 19:49:31:063 Information The connection "GroupVPN_0006B1030980" has been enabled. 2009/12/18 19:49:32:223 Information XXX.XXX.XXX.XXX Starting ISAKMP phase 1 negotiation. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX Starting aggressive mode phase 1 exchange. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX NAT Detected: Local host is behind a NAT device. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX The SA lifetime for phase 1 is 28800 seconds. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX Phase 1 has completed. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX Received XAuth request. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX XAuth has requested a username but one has not yet been specified. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX Sending phase 1 delete. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX User authentication information is needed to complete the connection. 2009/12/18 19:49:32:393 Information An incoming ISAKMP packet from XXX.XXX.XXX.XXX was ignored. 2009/12/18 19:49:36:962 Information XXX.XXX.XXX.XXX Starting ISAKMP phase 1 negotiation. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX Starting aggressive mode phase 1 exchange. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX NAT Detected: Local host is behind a NAT device. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX The SA lifetime for phase 1 is 28800 seconds. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX Phase 1 has completed. 2009/12/18 19:49:37:094 Information XXX.XXX.XXX.XXX Received XAuth request. 2009/12/18 19:49:37:100 Information XXX.XXX.XXX.XXX Sending XAuth reply. 2009/12/18 19:49:37:110 Information XXX.XXX.XXX.XXX Received initial contact notify. 2009/12/18 19:49:37:153 Information XXX.XXX.XXX.XXX Received XAuth status. 2009/12/18 19:49:37:154 Information XXX.XXX.XXX.XXX Sending XAuth acknowledgement. 2009/12/18 19:49:37:154 Information XXX.XXX.XXX.XXX User authentication has succeeded. 2009/12/18 19:49:37:247 Information XXX.XXX.XXX.XXX Received request for policy version. 2009/12/18 19:49:37:253 Information XXX.XXX.XXX.XXX Sending policy version reply. 2009/12/18 19:49:37:303 Information XXX.XXX.XXX.XXX Received policy change is not required. 2009/12/18 19:49:37:303 Information XXX.XXX.XXX.XXX Sending policy acknowledgement. 2009/12/18 19:49:37:303 Information XXX.XXX.XXX.XXX The configuration for the connection is up to date. 2009/12/18 19:49:37:377 Information XXX.XXX.XXX.XXX Starting ISAKMP phase 2 negotiation with 10.10.10.0/255.255.255.0:BOOTPC:BOOTPS:UDP. 2009/12/18 19:49:37:377 Information XXX.XXX.XXX.XXX Starting quick mode phase 2 exchange. 2009/12/18 19:49:37:472 Information XXX.XXX.XXX.XXX The SA lifetime for phase 2 is 28800 seconds. 2009/12/18 19:49:37:472 Information XXX.XXX.XXX.XXX Phase 2 with 10.10.10.0/255.255.255.0:BOOTPC:BOOTPS:UDP has completed. 2009/12/18 19:49:37:896 Information Renewing IP address for the virtual interface (00-60-73-4C-3F-45). 2009/12/18 19:49:40:189 Information The virtual interface has been added to the system with IP address 10.10.10.112. 2009/12/18 19:49:40:319 Information The system ARP cache has been flushed. 2009/12/18 19:49:40:576 Information XXX.XXX.XXX.XXX NetWkstaUserGetInfo returned: user: Dustin, logon domain: DT-WIN7, logon server: DT-WIN7 2009/12/18 19:49:53:457 Information XXX.XXX.XXX.XXX NetGetDCName failed: Could not find domain controller for this domain. 2009/12/18 19:49:53:457 Information XXX.XXX.XXX.XXX calling NetUserGetInfo: Server: , User: Dustin, level: 3 2009/12/18 19:49:53:460 Information XXX.XXX.XXX.XXX NetUserGetInfo returned: home dir: , remote dir: , logon script: 2009/12/18 19:49:53:466 Warning XXX.XXX.XXX.XXX Failed to execute script file \DT-WIN7netlogondomain.bat, Last Error: The network name cannot be found..

  Read the article

• Installing Win7 over PXE through Serva fails on Loading Network Resources

  - by Armand

  Trying to install Win7 OS to a Lenovo E335 with no DVD/CD. I have to do it either over PXE/Network or USB. Although I am able to get passt the installation menu of Serva, it fails on Loading Network Resources ... FAILED No NIC/Driver, ABORTING! This is the only log on the Serva Client PC and nothing on the Serva-server. Would appreciate if someone can tell me how to go pass this error. THe network card works fine, it has already loaded the Windows installation structure on a X: drive on the new laptop. Another detail: I am using a normal Ethernet Cable to connect the PCs. Should this be enough or a crossover cable is a must in this case?

  Read the article

• Event 4098, 0x80070533 Logon failure: account currently disabled?

  - by Josh King

  Having started to upgrade our PCs to Windows 7 we have noticed that we are getting group policy warnings in Event Viewer such as: "The user 'Word.qat' preference item in the 'a_Office2007_Users {A084A37B-6D4C-41C0-8AF7-B891B87FC53B}' Group Policy object did not apply because it failed with error code '0x80070533 Logon failure: account currently disabled.' This error was suppressed." 15 of these warnings appear every two hours on every Windows 7 PC, most of which are to do with core office applications and two are for plug-ins to out document management system. These warnings aren't afecting the users, but it would be nice to track down the source of them before we rollout Win7 to the rest of the Organisation. Any ideas as to where the login issue could be comming from (All users are connecting to the domain and proxy, etc fine)?

  Read the article

• Show me other ways to activate is disabled?

  - by Simon

  I have installed an instance of Win Server 2008 R2 on a Virtual machine. This machine is purposefully on an isolated environment (no internet) for testing purposes. I need to activate the machine and I have my MSDN key ready to go. I just ran through the same steps with a Windows 7 VM, and was able to register using an automated telephone service from Microsoft. With Windows Server 2008, I can see the same option to register using this service, but it is greyed out: Google pointed me to people experiencing this issue but the only workarounds I saw where to use the internet (not an option for me). Does anyone know how to enable this option?

  Read the article

• Import IIS6 website configuration into IIS7

  - by sinni800

  Hello, I have many websites hosted on IIS6 and I want to migrate them to IIS7. It is enough if the basic configuration (folder, virtual folders inside, hostheaders, ) is migrated. a great part of the configuration is in web.config anyway. It is even okay if they're just created as "classic" mode applications. I have tried the following things: Msdeploy. This copies the whole directoried though, not good... Tried exporting the iis websites to xml... Found nothing to give them to iis7... Anybody got an idea?

  Read the article

• Import IIS6 website configuration into IIS7

  - by sinni800

  Hello, I have many websites hosted on IIS6 and I want to migrate them to IIS7. It is enough if the basic configuration (folder, virtual folders inside, hostheaders, ) is migrated. a great part of the configuration is in web.config anyway. It is even okay if they're just created as "classic" mode applications. I have tried the following things: Msdeploy. This copies the whole directoried though, not good... Tried exporting the iis websites to xml... Found nothing to give them to iis7... Anybody got an idea?

  Read the article

• verify cert with certutil.exe

  - by Michal

  Hi, I have stupid problem, what is correct syntax on verify certificate in certificate store with certutil.exe. I have client certificate in cerstore. I try this: certutil.exe -verify CertCommonName but in finish with this error : DecodeFile returned The system cannot find the file specified. 0x80070002 (WIN32 : 2) LoadCert(Cert) returned The system cannot find the file specified. 0x80070002 (W IN32: 2) CertUtil: -verify command FAILED: 0x80070002 (WIN32: 2) CertUtil: The system cannot find the file specified. When I ping certutil.exe -ping it connect to pc.

  Read the article

• "No active network adapters found" Hyper-V 2008 R2

  - by mnemosyn

  I fiddled around with the virtual network settings of my Hyper-V server, because Windows Update failed to run in the VMs. I set the flag that makes the NIC exclusively usable by the VM. Now, the host system tells me it has no active network adapters. What does that even mean? According to netsh, there are three enabled network connections. I tried to restart the NICs using devcon.exe (the correct x64 version), but that doesn't make any difference - still, devcon reports the NICs are there and they are activated?! Is there any way I can force the host to re-enable the NICs?

  Read the article

• IE 8 plays sound, Ulead pop-up message appears, crash

  - by benzado

  I'm experiencing a problem on a new PC using Outlook Web Access in Internet Explorer 8. When OWA plays a sound, a message box appears: the about box for Ulead MP3 codec. When I click OK to dismiss the box, I get a message that IE has stopped responding and Windows eventually has to force the browser window closed. This is apparently not an isolated incident, occurring on computers from different manufacturers and on other websites that play sound (such as AOL's Webmail). The only "fix" I've found on discussion boards is to prevent the website from playing sound in the first place. That's not a fix, that's just avoiding the trigger. I'd like to know what's causing this and uninstall it or repair it, so the computer can work like it's supposed to. Since Super User users are smarter than the average bear, I thought I'd have better luck here.

  Read the article

• OpenVPN Problems, connecting with Windows OpenVPC client to Linux OpenVPN

  - by Filip Ekberg

  After following this guide and connecting to the VPN Server, I get the following error: Sat Mar 06 19:43:08 2010 us=127000 NOTE: failed to obtain options consistency info from peer -- this could occur if the remote peer is running a version of OpenVPN before 1.5-beta8 or if there is a network connectivity problem, and will not necessarily prevent OpenVPN from running (0 bytes received from peer, 0 bytes authenticated data channel traffic) -- you can disable the options consistency check with --disable-occ. I am using Archlinux and installed openvpn with Pacman. I want to acheive the following: Connect to the VPN Server, being able to route certain made up hosts through it. Is this possible? openvpn --version gives me the following openvpn --version OpenVPN 2.1.1 i686-pc-linux-gnu [SSL] [LZO2] [EPOLL] built on Jan 31 2010 Originally developed by James Yonan Copyright (C) 2002-2009 OpenVPN Technologies, Inc. <[email protected]> Suggestions?

  Read the article

• OpenVPN Problems, connecting with Windows OpenVPC client to Linux OpenVPN

  - by Filip Ekberg

  After following this guide and connecting to the VPN Server, I get the following error: Sat Mar 06 19:43:08 2010 us=127000 NOTE: failed to obtain options consistency info from peer -- this could occur if the remote peer is running a version of OpenVPN before 1.5-beta8 or if there is a network connectivity problem, and will not necessarily prevent OpenVPN from running (0 bytes received from peer, 0 bytes authenticated data channel traffic) -- you can disable the options consistency check with --disable-occ. I am using Archlinux and installed openvpn with Pacman. I want to acheive the following: Connect to the VPN Server, being able to route certain made up hosts through it. Is this possible? openvpn --version gives me the following openvpn --version OpenVPN 2.1.1 i686-pc-linux-gnu [SSL] [LZO2] [EPOLL] built on Jan 31 2010 Originally developed by James Yonan Copyright (C) 2002-2009 OpenVPN Technologies, Inc. <[email protected]> Suggestions?

  Read the article

• SonicPoint AP Clients Not Able To Connect With DHCP

  - by Mike Keller

  This is my first time setting up anything like this so please be gentle. I'm a web developer who fell into setting up a few SonicWall NSA 4200's... I've tried doing as much research on this through Google and ServerFault but haven't been able to hunt down an answer as to what I'm doing wrong. We've got two virtual access points set up here, one that is intended for employees (tied to X2) and the other for guests (tied to X2:V1). We are not using the DHCP server on the NSA 4200, but one already on the network. When a client connects to the employee SSID they are able to obtain a IP from the network's DHCP server. However when attempting to connect to the guest SSID the client does a search for a DHCP server but can't find one. Any clues, resources, answers would be appreciated.

  Read the article

< Previous Page | 423 424 425 426 427 428 429 430 431 432 433 434  | Next Page >