Search Results

Search found 5180 results on 208 pages for 'outside'.

Page 43/208 | < Previous Page | 39 40 41 42 43 44 45 46 47 48 49 50  | Next Page >

• QoS basics on a Cisco ASA

  - by qbn

  Could someone briefly explain how to use QoS on Cisco ASA 5505? I have the basics of policing down, but what about shaping and priorities? Basically what I'm trying to do is carve out some bandwidth for my VPN subnets (in an object-group called priority-traffic). I've seen this Cisco QoS document, however configuring shaping and priority-queue don't seem to have any effects in my test. A full download of the linux kernel from kernel.org will boost a ping to a server via VPN sky high. Policing has been successful in passing this test, although it doesn't seem as efficient (I cap non-vpn traffic at 3 of my 4.5 megabits of bandwidth). Am I misunderstanding the results of the test? I think there is some simple concept I'm not grasping here. EDIT: Here is my config thus far (I have 4.5 megabits of bandwidth): access-list priority-traffic extended permit ip object-group priority-traffic any access-list priority-traffic extended permit ip any object-group priority-traffic access-list priority-traffic extended permit icmp object-group priority-traffic any access-list priority-traffic extended permit icmp any object-group priority-traffic access-list non-priority-traffic extended deny ip object-group priority-traffic any access-list non-priority-traffic extended deny ip any object-group priority-traffic access-list non-priority-traffic extended permit ip any any priority-queue outside queue-limit 440 class-map non-priority-traffic match access-list non-priority-traffic class-map priority-traffic match access-list priority-traffic class-map inspection_default match default-inspection-traffic policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp policy-map outbound-qos-policy class non-priority-traffic police input 2500000 police output 2500000 class priority-traffic priority service-policy global_policy global service-policy outbound-qos-policy interface outside

  Read the article

• Exchange 2003: Fresh install, couple noob questions.

  - by Eli

  Hi All, Thanks for reading! I have a small network set up for a local office here, and have a fresh install of Exchange 2003 on our sole-server PDC. The network uses one domain, call it ourdomain.net, which is DNSed locally, but not DNSed for the actual domain, so ourdomain.net works from within the network, but from outside, it's just pointed to some domain parking. I have a completely different domain, call it emaildomain.com, which is currently setup for our website and email, which is hosted with a standard hosting company. We've been using a combination of Thunderbird and Outlook (with local .pst files) for email. I've been asked to setup Exchange to work with our email, but am not familiar with it. The install seems to have gone just fine. The question is: How do I get email from a domain outside our network to work with the exchange server? Do I need to move the email for that domain to point to our local server (I so hope not!), or can I just set exchange so somehow slurp mail from the existing mailboxes on our host for that domain's mail? Or are there better ideas I don't know to ask for? Any help very appreciated - thanks!

  Read the article

• Troubles installing/starting Redis via Resque

  - by Craig Flannagan

  Trying to complete instructions for Resque/Redis installation here: https://github.com/defunkt/resque/blob/master/README.markdown Am stuck at where I'm trying to start up Redis via Resque at the following command: Craig:/usr/local/src/resque$ rake redis:start (in /usr/local/src/resque) Detach with Ctrl+\ Re-attach with rake redis:attach ../../bin/dtach -A /tmp/redis.dtach ../../bin/redis-server ../../../etc/redis.conf rake aborted! Command failed with status (127): [../../bin/dtach -A /tmp/redis.dtach ../../...] (See full trace by running task with --trace) Rerunning with --trace (showing only part of trace): Craig:/usr/local/src/resque$ rake redis:start --trace (in /usr/local/src/resque) ** Invoke redis:start (first_time) ** Execute redis:start Detach with Ctrl+\ Re-attach with rake redis:attach ../../bin/dtach -A /tmp/redis.dtach ../../bin/redis-server ../../../etc/redis.conf rake aborted! Command failed with status (127): [../../bin/dtach -A /tmp/redis.dtach ../../...] /Users/craigflannagan/.rvm/gems/ruby-1.9.2-head@foo/gems/rake-0.8.7/lib/rake.rb:995:in `block in sh' Not sure what is wrong here - by the way, when I did those instructions $ git clone git://github.com/defunkt/resque.git $ cd resque $ PREFIX=<your_prefix> rake redis:install dtach:install $ rake redis:start I wasn't sure whether or not I was supposed to be doing #1 from within the Rails project, or if I was supposed to have the git clone create a new folder outside the Rails project (in this case, I chose to have folder created outside the project).

  Read the article

• ASA DHCP Relay configuration..

  - by Jeff

  I have locations in different cities, connected using 2 Cisco ASA devices. my main location, corporate, use the IP 192.168.1.x The second location, remote store, use the IP 192.168.3.x I have a DHCP server (192.168.1.254) at my corporate location. I have created a scope for the 192.168.1.x which works fine for the corporate location. I created a scope for the remote location (192.168.3.x) on my DHCP server and tried to configure the remote ASA DCHP Relay, on the remote ASA: I disabled the DHCP Server on the inside. I enabled DHCP Relay on the inside, with set route set at yes. I set the Global DHCP Relay Servers, specify up to four servers to which DHCP requests would be relayed. I added my DHCP, 192.168.1.254 I flashed these settings to the ASA and gave it a try, didn't do anything. am i missing something - forgetting something. not really sure what im doing wrong. DHCP Settings on remote ASA: dhcp-client update dns server both dhcpd dns 192.168.1.254 dhcpd ping_timeout 750 dhcpd domain JEWELS.LOCAL dhcpd auto_config outside dhcpd update dns both ! dhcpd address 192.168.3.2-192.168.3.33 inside ! dhcprelay server 192.168.1.254 outside dhcprelay enable inside dhcprelay setroute inside on my local ASA: i have two ACLs for UDP ports 67 and 68 permitting any inbound traffic from the remote locations IP ... dhcprelay timeout 120

  Read the article

• Lion server profile manager, device enrollment doesn't work

  - by user964406

  I am in the process of setting up Lion Servers profile manager to manage iPads on our local school network. I don't need to manage them while they are outside the network. I have successfully had it working on my personal network. The school network is behind a proxy which we have no control over. I can get the iPads to view the mydevices page and install a trust cert. I have managed to get an iPad to successfully install the remote management profile. After this the profile manager bugs out. It will list the active task of 'new device (sending)' but it's unable to complete the task. If I click on the device on profile manager and try any of the actions out they will all fail to complete. I am using the auto generated certificates and this works if I bring the server and iPad outside of the school network. Shortly after device enrollment the system log on the Lion server reports the following Replaced the actual ip address with INTERNALIP Jun 4 08:40:53 mini sandboxd[760] ([778]): applepushservice(778) deny network-outbound INTERNALIP:8080 Jun 4 08:40:53 mini sandboxd[760] ([778]): applepushservice(778) deny network-outbound INTERNALIP:8080 Jun 4 08:40:53 mini applepushserviced[778]: Got connection error Error Domain=NSPOSIXErrorDomain Code=1 "The operation couldn\u2019t be completed. Operation not permitted" UserInfo=0x7fa483b1a340 {NSErrorFailingURLStringKey=https://albert.apple.com/WebObjects/ALUnbrick.woa/wa/deviceActivation?device=Mac OS, NSErrorFailingURLKey=https://albert.apple.com/WebObjects/ALUnbrick.woa/wa/deviceActivation?device=Mac OS} Jun 4 08:40:53 mini applepushserviced[778]: Failed to get client cert on attempt 2, will retry in 15 seconds Does anyone have any ideas on how to get past this stage? Thanks in advance.

  Read the article

• Cisco ASA: Routing packets based on where the connections started from

  - by DrStalker

  We have a Cisco ASA 5505 (version 8.2(2)) with three interfaces: outside: IP address 11.11.11.11, this is the default route inside: IP address 10.1.1.1, this is the local subnet newlink: 22.22.22.22, this is a new internet connection. We need to move VPN users from the 11.11.11.11 address to the 22.22.22.22 address, and we're using SSH on the ASA as to test and sort out the routing. The problem we have is this: If we define a particular IP as being on a static route out the newlink interface then it can SSH to 22.22.22.22 fine. If we do not define a static route then the traffic hits the ASA, but the return traffic does not come back over newlink; presumably it gets sent over the outside interfcae as that is the default route. We can't define a static route for each remote endpoint because there are dialup VPN users, who obviously change IP a lot What we need to do is configure the ASA so if a connection comes in on the newlink interface then the outgoing packets for that go over the newlink interface, not the default route. With iptables this should be do-able by marking the connection and doing mark-routing, but what is the equivalent for a Cisco ASA?

  Read the article

• VPN Error 619: Behind Cisco Router WRT310N

  - by ty91011

  I've researched a lot on all the forums and this error is too generic for any of the proposed solutions to work. I'll try to give as much detail and tried solutions. I'm running a CentOS PPTP server behind a Cisco WRT310N Router. Multiple clients from outside with different OS have failed with the same error 619, along with turning off windows firewall and disabling antivirus. I believe this is a router and IP routing issue, and not a client issue. When I connect from a client on the same router as the VPN server, it works when I use the 192. network address- but doesn't work with the public IP address. I've tried telnet to port 1723 from an outside server and I get in. I've opened up the VPN port (1723) on the router, VPN udp port (500), and the GRE port (47) to route to the VPN server's ip. Also, the server's router is behind a DSL modem. I had a glimmer of hope when this site: http://www.chicagotech.net/casestudy/vpnerror619.htm suggested that the PPoE authentication should reside on the router and not the modem. But I still came up empty. So does anybody know what the problem is?

  Read the article

• Apache directory structure with multiple hosted languages.

  - by anomareh

  I just got a new work machine up and running and I'm trying to decide on how to set everything up directory wise. I've done some digging around and really haven't been able to find anything conclusive. I know it's a question with a variety of answers but I'm hoping there's some sort of general guidelines or best practices to go by. With that said, here are a few things specific to my situation. I will be doing actual development and testing on the same machine as the server. It is a single user machine in the sense that I will be the only one working on the machine. There will be multiple hosted languages, specifically PHP and RoR while possibly expanding later. I'd like the setup to translate well to a production environment. With those 3 things in mind there are a couple of things I've had in the back of mind. Seeing as it's a single user machine I haven't been able to decide whether or not I should be working on things out of my home directory or if they should be located outside of it. I'm feeling that outside of a user directory would be better as it would translate better to a production environment, but I'm also not sure if that will come with any permission annoyances or concerns seeing as I'll be working on the same machine. Hosting multiple languages seems like it may be a bit quirky. With PHP I've found you're generally just dumping the project somewhere in the document root where as something like a Rails app you have the entire project and you only want the public directory in the document root. Thanks for any insight, opinion, or just personal preference from experience anyone can offer.

  Read the article

• chef clients behind firewall

  - by tec

  I am currently learning about chef. What I understood so far: I have to install chef-server on an own server or use the hosted chef. I have to install chef-client on the servers that I want to manage aka nodes (manually or using knife bootstrap). I installed several chef tools on my own PC that I can use to manage the nodes, e.g. knife. Now in my case the specialty is that the nodes are behind a firewall/load balancer/proxy. The nodes can access servers on the outside via NAT (http works and I can configure chef-specific hosts to work as well). However they can only be contacted from the outside via a ssh tunnel. There is really much documentation about chef available but I did not find an answer to these questions: When using knife, is it enough when I set up a ssh tunnel manually on my own PC or does the chef server need to contact the nodes? When using knife, can I configure it to setup a ssh tunnel automatically? When using the chef server web ui can I configure it to connect to the nodes via ssh tunnel or do I need a setup where I setup the tunnel myself e.g. using monit? Is this even possible with hosted chef? Instead of using knife or the web ui: Can I issue the same management commands directly on the nodes using chef-client? What solution would you recommend? Thanks a lot for taking your time to help and answering one or more of these related questions

  Read the article

• Skype Connect as SIP/Trunk for Asterisk

  - by Kaurin

  First off: I'm not sure if this should be on superuser or here. I have recently built a few Asterisk boxes with OpenVOX FXO/FXS ports little or no trouble. My current project is building an Asterisk box with SIP trunks. My current employer insisted on getting Skype Business/Skype connect for that purpose. After reviewing the Skype Connect plan, I agreed, because I thought it is going to be straightforward: Purchase G729 licences and setup SIP trunk/trunks. Boy was i wrong :) Here is the setup: The setup is for calling US numbers only via skype (we got skype US minute bundles in skype connect) AsteriskNOW - Asterisk 1.4 + asterisk-gui Trunks: SIP Trunk configured with Skype Connect - shows as registered Users: 2 test extensions. Both work fine when calling each other, voicemail etc works fine too The asterisk box is behind a Mikrotik router which i configured to forward all relevant ports: 5060-5090 UDP, 10000-20000 UDP. When trying out an extension outside of my LAN, it worked. I could make calls to the other extension. Outgoing rule: _NXXXXXXXXX Strip:0 Prepend:+1 Use skype trunk Inbound rule: Trunk: Skype Pattern: s Destination: Extension1 (6210) Here is the output of asterisk CLI (-rvvvvv) with outgoing calls: http://pastebin.com/eWVpL72e you can see the circuit-busy response when using trunk1 (skype) When calling my Skype Connect number from the outside, I get nothing in the logs. Can anyone with Skype Connect / Asterisk experience help out? :)

  Read the article

• AD server within another network - DNS issues

  - by Harry Muscle

  Here's a quick summary of the environment I support: we have a domain (domain A) that has about 20 client computers. The domain server for this domain and all the clients sit within the network infrastructure of a larger domain (domain B). All the computers get their network settings via DHCP from domain B's servers. I have no control and am unable to make changes to anything to do with domain B. The problem I have is that currently in order for my domain's (domain A) clients to be able to resolve the domain server and the shares on it they have their DNS server IP address set to domain A's domain server (via the default GPO). Unfortunately when a laptop (windows and mac) gets taken home, they are still looking for the domain server as their DNS server and obviously can't access the internet correctly outside of our environment. Ideally I need a solution where the machines use domain A's domain server as their DNS when inside the office and use what ever DNS server DHCP gives them when they are outside the office. However, since I have no control over the office DHCP server, I'm not sure how this can be accomplished. Any help and advice that anyone can offer is highly appreciated. Thanks, Harry P.S. The solution I'm trying to find needs to require no involvement from the user.

  Read the article

• Terminating multi-mode fiber

  - by murisonc

  I'm looking at the feasibility of terminating multi-mode fiber connections ourselves. We would be using LC connectors. I've done some research and found two different methods. One requires polishing the ends and using epoxy while the other doesn't. I like the idea of not having to polish the ends but there doesn't seem to be much information on quality or ease of use. I've found two vendors (3M and Corning) that offer kits for terminating fiber without polishing or using epoxy. Does anyone have any experience with both methods that can offer some advice? Copper is easy but fiber seems to be a whole different animal. EDIT: After looking into fusion splicing suggested in the answer I've determined it's not for us. It's my understanding that is primarily used for outside plant and is better suited for single mode fiber. It's a good answer but doesn't address the question directly. Some more information about our situation. We will only be terminating multi-mode fiber inside a building and only doing between 4 and 20 pair a year. Hiring an outside person won't work due to our location. There are currently a couple people on-site that can terminate fiber (working for another company and charging large fees) but they can only do ST and SC connectors and we only use LC. So once again does anyone have experience with terminating using both epoxy type connectors and the other type (similar to Corning Unicam)?

  Read the article

• Is it possible to setup an internal test email server to keep all mail sent to it?

  - by MattGrommes

  We have a need at my work to setup a test email server that will take all mail sent to it for delivery and instead just dump it into an account for later retrieval. I've been out of the email server configuration game long enough that I think that's possible but I don't know for sure. As a more specific example of what we need: We have code that sends emails to outside clients in certain cases. We want to point our code to a test server that will accept those emails, but not let them get to the outside world (yes, it's happened before, oops). We then need to be able to verify that Email X would have gotten sent to Client Y if we had sent to the real server. As a bonus, we have a error email alias on our real server that goes to the programmers that we would like to keep getting email from. So anything sent to that alias on the test server would forward to our real server for delivery. My preference is for postfix but our IT staff seems set on using sendmail (or Exchange) for everything so hints/pointers for either server would be helpful. Thanks a lot.

  Read the article

• Windows Server 2008 R2 DNS - One IP, multiple servers

  - by Blu Dragon

  I need opinions and examples on how to best to accomplish the setup I am looking for. I have a public-facing AD domain server with one public IP address. I have setup an external zone for example.com and I successfully have my own name servers pointing to it at ns0.example.com and ns1.example.com. I also have an internal zone for my private network at home.example.com. I am behind a router with the domain server in the DMZ. I want dev.example.com to be accessible from the outside world over https and to point to internal IP address 192.168.1.78. Likewise, I want www.example.com to be accessible from the outside world and point to internal IP address 192.168.1.79. Both dev and www servers are CentOS 5.6 VMs running inside of Hyper-V on the domain server (bad idea I know but I am limited on hardware atm). What is best way to achieve this? From what I have read and researched on Google, I may need to setup a reverse proxy but I am not sure how well that will work with SSL.

  Read the article

• Public-to-Public IPSec tunnel: NAT confusion

  - by WuckaChucka

  I know this is possible -- and apparently fairly common with larger companies that don't/can't route private addresses for overlap reasons -- but I can't wrap my head around how to get this to work. I'm playing around with pfSense, Vyatta and a Cisco 5505 right now, hardware-wise. So here's my setup: WEST: Vyatta outside: 10.0.0.254/24 inside: 172.16.0.1/24 machine a: 172.16.0.200/24 EAST: Cisco 5505 outside: 10.0.0.210/24 inside: 192.168.10.1 machine b (webserver): 192.168.10.2 So what we're trying to do is this: route traffic across the tunnel from machine A to machine B without using private addresses. i.e. 172.16.0.200 makes a TCP request to 10.0.0.210:80, and as far as EAST is concerned, it sees a src IP of 10.0.0.254. On WEST, I have your typical many-to-one Source NAT to translate 172.16.0.0/24 to 10.0.0.254 and that's confirmed to be working. Also on WEST, I have the following IPSec config: Local IP: 10.0.0.254 Peer IP: 10.0.0.210 local subnet: 10.0.0.254/32 remote subnet: 10.0.0.210/32 I have the reversed configuration on EAST. What happens when I make a request from machine A to 10.0.0.210:80 is that the SNAT translates the private address of machine A to 10.0.0.254 and it's routed out (and discarded at the other end) without establishing the tunnel. What I'm assuming is happening is that the inside interface on WEST receives a packet from 172.16.0.200 and since this doesn't match the local subnet defined in the tunnel configuration, it's not processed by the IPSec engine and the tunnel is not established. How do you make this work? Seems like a chicken and egg thing with the NAT and IPSec and I just can't wrap my head around how this can be done: can I say, "if a packet is received on the inside interface with a destination of 10.0.0.210, translate it to 10.0.0.254 before the IPSec engine inspects it"?

  Read the article

• Problem hosting server behing personal router

  - by Venkatesh Hodavdekar

  I recently bought the domain name lucidcontraptions.com and want to host the website from home. I have a D-Link router in which I have set up my personal virtual server correctly. My application server is Apache 2.2. The server works perfectly with the following settings: External IP: 207.172.xx.xx. Public port: 8888 Internal IP: 192.168.xx.xx. Private port: 80 If I go to 207.172.xx.xx:8888/ the server works perfectly and my Apache page shows up without any issues, both from inside the intranet as well as outside. This setting would not work out for me as I am not allowed port numbers in my DNS management. Now when I tweak the settings to the following: External IP: 207.172.xx.xx. Public port: 80 Internal IP: 192.168.xx.xx. Private port: 80 If I go to 207.172.xx.xx/ the server works perfectly and my Apache page shows up without any issues, BUT ONLY FROM INSIDE THE INTRANET. This page does not show up for people outside the intranet.

  Read the article

• What are the attack vectors for passwords sent over http?

  - by KevinM

  I am trying to convince a customer to pay for SSL for a web site that requires login. I want to make sure I correctly understand the major scenarios in which someone can see the passwords that are being sent. My understanding is that at any of the hops along the way can use a packet analyzer to view what is being sent. This seems to require that any hacker (or their malware/botnet) be on the same subnet as any of the hops the packet takes to arrive at its destination. Is that right? Assuming some flavor of this subnet requirement holds true, do I need to worry about all the hops or just the first one? The first one I can obviously worry about if they're on a public Wifi network since anyone could be listening in. Should I be worried about what's going on in subnets that packets will travel across outside this? I don't know a ton about network traffic, but I would assume it's flowing through data centers of major carriers and there's not a lot of juicy attack vectors there, but please correct me if I am wrong. Are there other vectors to be worried about outside of someone listening with a packet analyzer? I am a networking and security noob, so please feel free to set me straight if I am using the wrong terminology in any of this.

  Read the article

• RRAS Public Address Pool on Windows Server 2008

  - by Art

  I have a Windows 2008 server with two NICs running RRAS and a small public website. It also does NAT for several other PCs on my network and everything works great. I have a block of 5 public static IPs from my ISP, one of which is bound to the public NIC in the Windows 2008 server. I would like to assign one of the remainging 4 public IPs to a machine on my private network. I thought I could do this by going into RRAS, selecting NAT under IPv4 and then adding the public IP address to the address pool and specifying a reservation for the machine I would like to use that address by adding its private ip address. When I do this, the machine I reserved the public IP address for seems to loose all outside network connectivity. I can still ping other PCs on my 192.168.0.* net, but anything outside is no longer reachable. When I remove the reservation, everything seems to work. After setting the reservation and right clicking on the external public interface and selecting 'Show Mappings' I can see outbound requests from my private address with the desired associated private address, however I do not see any inbound requests. What am I doing wrong/missing?

  Read the article

• How to setup Mac server to use two gateways

  - by Brady

  I recently asked this question: How to set Mac server to use different Gateway for internet bound traffic The answer given works but has presented me with another issue that I didnt make clear in that question. Here is my network layout as it stands: At the moment outside staff members use some services on the existing internet 1 link. Those services are hosted by the Mac server. If I change the gateway of the Mac server to the second modem those outside staff lose visabilty on those services. Now I dont know how to go about solving this issue. I want the second link to be used when the Mac server goes to rsync data offsite but everything else use link one. How do I do this? Thanks Scott EDIT: This has been resolved by setting the default gateway on the Mac server to 192.168.1.254 Thus leaving everything on the network as it was before. but to get the Mac server to use the other link for rsync I've added a route to the Mac server to route traffic to the rsync server through the second gateway. sudo route add -net {server IP's}/{Netmask} 192.168.1.1 I've awarded the answer to gravyface for pointing me to a post on how to make this route persistant in Mac

  Read the article

• Configuration Help for Sendmail Required

  - by Vinayak Mahadevan

  Hi I need some help with respect to sendmail configuration. The basic problem is that I have some employees working from other places and they need access to their mail. So what I have done right now is whatever mails which are meant for them which are generated from within the company and collected by my internal mail server is bounced to an external mail server from where the employees access it. This is done through a email id on a different domain. This was working fine till I restricted the external mailing access for certain users using rulesets in sendmail.cf. Once I had put that in place only people who had external mailing rights could send mails to people outside the office. What I would like to know is that is there anyway where I can expose sendmail on two different ips and thereby configure everybody's email id to point to the same internal mail server using 2 different ips. one ip when inside the company and one ip outside the company. Is it possible that I have one static ip configured for both internal access and external access or is there any otherway it can be done with sendmail. Can anybody help me Sorry for the long post Regards Vinayak

  Read the article

• How can I debug a port/connectivity issue?

  - by rfw21

  I am running a simple WebSocket server on Amazon EC2 (Fedora Core). I've opened the relevant port using ec2-authorize, and checked that it's opened. Iptables is definitely not running. However I can't connect to the port from outside EC2. I've tried the following (my server is running on port 7000): telnet ec2-public-dns.xx.xx.xx.amazon.com 7000 (from within EC2: connects fine) nmap localhost (output includes line: 7000/tcp open afs3-fileserver) telnet ec2-public-dns.xx.xx.xx.amazon.com 7000 (this time from my local machine: I get "connection refused: Unable to connect to remote host") The strange thing is this: if I start Nginx on port 7000 then it works and I can connect from outside EC2! And the WebSocket server fails on port 80, where Nginx works fine. To me this suggests a problem with the WebSocket server, BUT I can connect to it successfully from within EC2. (And it works fine on a different VPS account). How can I debug this further? If anybody can stop me tearing my hair out, I'd be very grateful indeed :)

  Read the article

• Cisco ASA dropping IPsec VPN between istself and CentOS server

  - by sebelk

  Currently we're trying to set up an IPsec VPN between a Cisco ASA Version 8.0(4) and a CentOS Linux server. The tunnel comes up successfully, but for some reason that we can't figure out, the firewall is dropping packets from the VPN. The IPsec settings in the ASA sre as follows: crypto ipsec transform-set up-transform-set esp-3des esp-md5-hmac crypto ipsec transform-set up-transform-set2 esp-3des esp-sha-hmac crypto ipsec transform-set up-transform-set3 esp-aes esp-md5-hmac crypto ipsec transform-set up-transform-set4 esp-aes esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map linuxserver 10 match address filtro-encrypt-linuxserver crypto map linuxserver 10 set peer linuxserver crypto map linuxserver 10 set transform-set up-transform-set2 up-transform-set3 up-transform-set4 crypto map linuxserver 10 set security-association lifetime seconds 28800 crypto map linuxserver 10 set security-association lifetime kilobytes 4608000 crypto map linuxserver interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption aes hash sha group 2 lifetime 28800 crypto isakmp policy 2 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 crypto isakmp policy 3 authentication pre-share encryption aes-256 hash md5 group 2 lifetime 86400 crypto isakmp policy 4 authentication pre-share encryption aes-192 hash sha group 2 lifetime 86400 crypto isakmp policy 5 authentication pre-share encryption aes-192 hash md5 group 2 group-policy linuxserverip internal group-policy linuxserverip attributes vpn-filter value filtro-linuxserverip tunnel-group linuxserverip type ipsec-l2l tunnel-group linuxserverip general-attributes default-group-policy linuxserverip tunnel-group linuxserverip ipsec-attributes pre-shared-key * Does anyone know where the problem is and how to fix it?

  Read the article

• Conditionally Rewrite Email Headers (From & Reply-To) Exchange 2010

  - by NorthVandea

  I have a client who maintains Company A (with email addresses %username%@companyA.com) and they own the domain companyB.com however there is no "infrastructure" (no Exchange server) set up specifically for companyB.com. My client needs to be able to have the end users within it's company (companyA.com) add a specific word or phrase to the Subject (or Body) line of the Outgoing email (they are only concerned with outgoing, incoming is a non-issue in this case) that triggers the Exchange 2010 servers to rewrite the header From and Reply-To [email protected] with [email protected] but this re-write should ONLY occur if the user places the key word/phrase in the Subject (or Body). I have attempted using Transport Rules and the New-AddressRewriteEntry cmdlet however each seems to have a limitation. From what I can tell Transport Rules cannot re-write the From/Reply-To fields and New-AddressRewriteEntry cannot be conditionally triggered based on message content. So to recap: User sends email outside the organization: From and Reply-To remain [email protected] User sends email outside the organization WITH "KeyWord" in the Subject or Body: From and Reply-To change to [email protected] automatically. Anyone know how this could be done WITHOUT coding a new Mail Agent? I don't have the programming knowledge to code a custom Agent... I can use any function of Exchange Management Shell or Console. Alternatively if anyone knows of a simple add-on program that could do this that would be good too. Any help would be greatly appreciated! Thank you!!!

  Read the article

• Anyone know a good mind mapper that works with a scheduler?

  - by GLycan

  TL;DR: Mind mapping tasks to be processed into a schedule based on task metadata. I have all sorts of ideas about what to invest resources (mainly time) in, but when I actually have time to do something I useually end up browsing reddit for not knowing what do to, and the frequancy with which I forget deadlines scares me. I'd love to bring order and structure into my mind, and always know what to do next. So, I want a mind mapping app, where I'd give each branch (types and subtypes of things I want to do) a importance score (if there were two branches, and one had 60 while the other 40, they would respectivily get 60% and 40% of the parent's importance, with the root being 100) and a how soon that branch should be revised/updated (an hobby I want to try out might be checked, say, once a week, while a school subject should be checked once a day) and give each leaf (something I want/need to do) how much time it takes, deadline (if any), and optionally an absolute importance, reoccurrence (guitar practice might repeat once a week), and prerequisites (reading something requires that book (although that could be brought somewhere), coding requires a box, jogging requires being outside) and maybe some other flags, like if it's enjoyable or not. It should either be packaged or working with a schedular app, to which I'd say, look, my day works this way (completely busy from 8 to 9:15, then 15 minutes of being inside with nothing, ..., two hours with box and possibility to go outside, etc), saying that such-and-such pattern is school and happens ever weekday except such-and-such days. The output should be of the form of a schedule, fit for printing or, when I finally get an android, mobile viewing, that schedules tasks with regards to availability of resources and importance (importance being derived from the leaf-task's parent branches), and the set of flags (all work and no play makes me a dull boy). One of these tasks should be reviewing anything that should be updated on that day, including future day layouts (e.g, if the time slots of future days have changed. This should be done every day.) Does anyone know some collection of preferably open-source (or free, or pirateable) tools, or better yet a single one, that accomplishes this task? I know python pretty well, and should be able to write any necessary glue.

  Read the article

• Unable to browse to apache service, Service is running

  - by Jeff

  Summary I have a very peculiar problem. I am not able to open the "It Works!" page after installing a fresh server with apache. I am able to ssh to the box (from outside the network). Apache seems to be running on my Centos6.4x86_64 box just fine. Nothing useful in /var/logs/httpd/*. What am I missing? The setup I am outside the network right now. The "server" is a VM on my home computer running bridged mode. public ip: A.B.C.D Host: 192.168.1.5 VM: 192.168.1.8 I have a verizon fios router that is forwarding ports 22, 80, and 8888 to the VM. I am able to ssh over port 22, but I am not able to browse to the public URL over port 80. so A.B.C.D:22 is working, but http://A.B.C.D:80 is not. What I've tried nmap to see if it is listening: nmap -sT -O localhost Starting Nmap 5.51 ( http://nmap.org ) at 2013-10-25 11:10 EDT Nmap scan report for localhost (127.0.0.1) Host is up (0.000040s latency). Other addresses for localhost (not scanned): 127.0.0.1 Not shown: 996 closed ports PORT STATE SERVICE 22/tcp open ssh 25/tcp open smtp 80/tcp open http 3306/tcp open mysql I tried going to it locally (lynx) and it does work. So, is the problem in my ports?

  Read the article

< Previous Page | 39 40 41 42 43 44 45 46 47 48 49 50  | Next Page >