Search Results

Search found 11629 results on 466 pages for 'cloud solutions'.

Page 437/466 | < Previous Page | 433 434 435 436 437 438 439 440 441 442 443 444  | Next Page >

  • Setting up a VPN connection to Amazon VPC - routing

    - by Keeno
    I am having some real issues setting up a VPN between out office and AWS VPC. The "tunnels" appear to be up, however I don't know if they are configured correctly. The device I am using is a Netgear VPN Firewall - FVS336GV2 If you see in the attached config downloaded from VPC (#3 Tunnel Interface Configuration), it gives me some "inside" addresses for the tunnel. When setting up the IPsec tunnels do I use the inside tunnel IP's (e.g. 169.254.254.2/30) or do I use my internal network subnet (10.1.1.0/24) I have tried both, when I tried the local network (10.1.1.x) the tracert stops at the router. When I tried with the "inside" ips, the tracert to the amazon VPC (10.0.0.x) goes out over the internet. this all leads me to the next question, for this router, how do I set up stage #4, the static next hop? What are these seemingly random "inside" addresses and where did amazon generate them from? 169.254.254.x seems odd? With a device like this, is the VPN behind the firewall? I have tweaked any IP addresses below so that they are not "real". I am fully aware, this is probably badly worded. Please if there is any further info/screenshots that will help, let me know. Amazon Web Services Virtual Private Cloud IPSec Tunnel #1 ================================================================================ #1: Internet Key Exchange Configuration Configure the IKE SA as follows - Authentication Method : Pre-Shared Key - Pre-Shared Key : --- - Authentication Algorithm : sha1 - Encryption Algorithm : aes-128-cbc - Lifetime : 28800 seconds - Phase 1 Negotiation Mode : main - Perfect Forward Secrecy : Diffie-Hellman Group 2 #2: IPSec Configuration Configure the IPSec SA as follows: - Protocol : esp - Authentication Algorithm : hmac-sha1-96 - Encryption Algorithm : aes-128-cbc - Lifetime : 3600 seconds - Mode : tunnel - Perfect Forward Secrecy : Diffie-Hellman Group 2 IPSec Dead Peer Detection (DPD) will be enabled on the AWS Endpoint. We recommend configuring DPD on your endpoint as follows: - DPD Interval : 10 - DPD Retries : 3 IPSec ESP (Encapsulating Security Payload) inserts additional headers to transmit packets. These headers require additional space, which reduces the amount of space available to transmit application data. To limit the impact of this behavior, we recommend the following configuration on your Customer Gateway: - TCP MSS Adjustment : 1387 bytes - Clear Don't Fragment Bit : enabled - Fragmentation : Before encryption #3: Tunnel Interface Configuration Your Customer Gateway must be configured with a tunnel interface that is associated with the IPSec tunnel. All traffic transmitted to the tunnel interface is encrypted and transmitted to the Virtual Private Gateway. The Customer Gateway and Virtual Private Gateway each have two addresses that relate to this IPSec tunnel. Each contains an outside address, upon which encrypted traffic is exchanged. Each also contain an inside address associated with the tunnel interface. The Customer Gateway outside IP address was provided when the Customer Gateway was created. Changing the IP address requires the creation of a new Customer Gateway. The Customer Gateway inside IP address should be configured on your tunnel interface. Outside IP Addresses: - Customer Gateway : 217.33.22.33 - Virtual Private Gateway : 87.222.33.42 Inside IP Addresses - Customer Gateway : 169.254.254.2/30 - Virtual Private Gateway : 169.254.254.1/30 Configure your tunnel to fragment at the optimal size: - Tunnel interface MTU : 1436 bytes #4: Static Routing Configuration: To route traffic between your internal network and your VPC, you will need a static route added to your router. Static Route Configuration Options: - Next hop : 169.254.254.1 You should add static routes towards your internal network on the VGW. The VGW will then send traffic towards your internal network over the tunnels. IPSec Tunnel #2 ================================================================================ #1: Internet Key Exchange Configuration Configure the IKE SA as follows - Authentication Method : Pre-Shared Key - Pre-Shared Key : --- - Authentication Algorithm : sha1 - Encryption Algorithm : aes-128-cbc - Lifetime : 28800 seconds - Phase 1 Negotiation Mode : main - Perfect Forward Secrecy : Diffie-Hellman Group 2 #2: IPSec Configuration Configure the IPSec SA as follows: - Protocol : esp - Authentication Algorithm : hmac-sha1-96 - Encryption Algorithm : aes-128-cbc - Lifetime : 3600 seconds - Mode : tunnel - Perfect Forward Secrecy : Diffie-Hellman Group 2 IPSec Dead Peer Detection (DPD) will be enabled on the AWS Endpoint. We recommend configuring DPD on your endpoint as follows: - DPD Interval : 10 - DPD Retries : 3 IPSec ESP (Encapsulating Security Payload) inserts additional headers to transmit packets. These headers require additional space, which reduces the amount of space available to transmit application data. To limit the impact of this behavior, we recommend the following configuration on your Customer Gateway: - TCP MSS Adjustment : 1387 bytes - Clear Don't Fragment Bit : enabled - Fragmentation : Before encryption #3: Tunnel Interface Configuration Outside IP Addresses: - Customer Gateway : 217.33.22.33 - Virtual Private Gateway : 87.222.33.46 Inside IP Addresses - Customer Gateway : 169.254.254.6/30 - Virtual Private Gateway : 169.254.254.5/30 Configure your tunnel to fragment at the optimal size: - Tunnel interface MTU : 1436 bytes #4: Static Routing Configuration: Static Route Configuration Options: - Next hop : 169.254.254.5 You should add static routes towards your internal network on the VGW. The VGW will then send traffic towards your internal network over the tunnels. EDIT #1 After writing this post, I continued to fiddle and something started to work, just not very reliably. The local IPs to use when setting up the tunnels where indeed my network subnets. Which further confuses me over what these "inside" IP addresses are for. The problem is, results are not consistent what so ever. I can "sometimes" ping, I can "sometimes" RDP using the VPN. Sometimes, Tunnel 1 or Tunnel 2 can be up or down. When I came back into work today, Tunnel 1 was down, so I deleted it and re-created it from scratch. Now I cant ping anything, but Amazon AND the router are telling me tunnel 1/2 are fine. I guess the router/vpn hardware I have just isnt up to the job..... EDIT #2 Now Tunnel 1 is up, Tunnel 2 is down (I didn't change any settings) and I can ping/rdp again. EDIT #3 Screenshot of route table that the router has built up. Current state (tunnel 1 still up and going string, 2 is still down and wont re-connect)

    Read the article

  • Android sending lots of SMS messages

    - by Robert Parker
    I have a app, which sends a lot of SMS messages to a central server. Each user will probably send ~300 txts/day. SMS messages are being used as a networking layer, because SMS is almost everywhere and mobile internet is not. The app is intended for use in a lot of 3rd world countries where mobile internet is not ubiquitous. When I hit a limit of 100 messages, I get a prompt for each message sent. The prompt says "A large number of SMS messages are being sent". This is not ok for the user to get prompted each time to ask if the app can send a text message. The user doesn't want to get 30 consecutive prompts. I found this android source file with google. It could be out of date, I can't tell. It looks like there is a limit of 100 sms messages every 3600000ms(1 day) for each application. http://www.netmite.com/android/mydroid/frameworks/base/telephony/java/com/android/internal/telephony/gsm/SMSDispatcher.java /** Default checking period for SMS sent without uesr permit */ private static final int DEFAULT_SMS_CHECK_PERIOD = 3600000; /** Default number of SMS sent in checking period without uesr permit */ private static final int DEFAULT_SMS_MAX_ALLOWED = 100; and /** * Implement the per-application based SMS control, which only allows * a limit on the number of SMS/MMS messages an app can send in checking * period. */ private class SmsCounter { private int mCheckPeriod; private int mMaxAllowed; private HashMap<String, ArrayList<Long>> mSmsStamp; /** * Create SmsCounter * @param mMax is the number of SMS allowed without user permit * @param mPeriod is the checking period */ SmsCounter(int mMax, int mPeriod) { mMaxAllowed = mMax; mCheckPeriod = mPeriod; mSmsStamp = new HashMap<String, ArrayList<Long>> (); } boolean check(String appName) { if (!mSmsStamp.containsKey(appName)) { mSmsStamp.put(appName, new ArrayList<Long>()); } return isUnderLimit(mSmsStamp.get(appName)); } private boolean isUnderLimit(ArrayList<Long> sent) { Long ct = System.currentTimeMillis(); Log.d(TAG, "SMS send size=" + sent.size() + "time=" + ct); while (sent.size() > 0 && (ct - sent.get(0)) > mCheckPeriod ) { sent.remove(0); } if (sent.size() < mMaxAllowed) { sent.add(ct); return true; } return false; } } Is this even the real android code? It looks like it is in the package "com.android.internal.telephony.gsm", I can't find this package on the android website. How can I disable/modify this limit? I've been googling for solutions, but I haven't found anything.

    Read the article

  • How can you add a UIGestureRecognizer to a UIBarButtonItem as in the common undo/redo UIPopoverContr

    - by SG
    Problem In my iPad app, I cannot attach a popover to a button bar item only after press-and-hold events. But this seems to be standard for undo/redo. How do other apps do this? Background I have an undo button (UIBarButtonSystemItemUndo) in the toolbar of my UIKit (iPad) app. When I press the undo button, it fires it's action which is undo:, and that executes correctly. However, the "standard UE convention" for undo/redo on iPad is that pressing undo executes an undo but pressing and holding the button reveals a popover controller where the user selected either "undo" or "redo" until the controller is dismissed. The normal way to attach a popover controller is with presentPopoverFromBarButtonItem:, and I can configure this easily enough. To get this to show only after press-and-hold we have to set a view to respond to "long press" gesture events as in this snippet: UILongPressGestureRecognizer *longPressOnUndoGesture = [[UILongPressGestureRecognizer alloc] initWithTarget:self action:@selector(handleLongPressOnUndoGesture:)]; //Broken because there is no customView in a UIBarButtonSystemItemUndo item [self.undoButtonItem.customView addGestureRecognizer:longPressOnUndoGesture]; [longPressOnUndoGesture release]; With this, after a press-and-hold on the view the method handleLongPressOnUndoGesture: will get called, and within this method I will configure and display the popover for undo/redo. So far, so good. The problem with this is that there is no view to attach to. self.undoButtonItem is a UIButtonBarItem, not a view. Possible solutions 1) [The ideal] Attach the gesture recognizer to the button bar item. It is possible to attach a gesture recognizer to a view, but UIButtonBarItem is not a view. It does have a property for .customView, but that property is nil when the buttonbaritem is a standard system type (in this case it is). 2) Use another view. I could use the UIToolbar but that would require some weird hit-testing and be an all around hack, if even possible in the first place. There is no other alternative view to use that I can think of. 3) Use the customView property. Standard types like UIBarButtonSystemItemUndo have no customView (it is nil). Setting the customView will erase the standard contents which it needs to have. This would amount to re-implementing all the look and function of UIBarButtonSystemItemUndo, again if even possible to do. Question How can I attach a gesture recognizer to this "button"? More specifically, how can I implement the standard press-and-hold-to-show-redo-popover in an iPad app? Ideas? Thank you very much, especially if someone actually has this working in their app (I'm thinking of you, omni) and wants to share...

    Read the article

  • Google slideshow shows a blank screen when calling from ajax

    - by ufk
    I'm having problems implementing google slideshow (http://www.google.com/uds/solutions/slideshow/index.html) to my web application by loading it using a jquery load() function. index.html: <script type="text/javascript" src="jquery-1.3.2.js"></script> <div id="moshe"></div> <script type="text/javascript"> $(document).ready(function(){ $('#moshe').load('test.html'); }); </script> test.html: <script type="text/javascript"> function load() { var samples = "http://dlc0421.googlepages.com/gfss.rss"; var options = { displayTime: 2000, transistionTime: 600, linkTarget : google.feeds.LINK_TARGET_BLANK }; new GFslideShow(samples, "slideshow", options); } google.load("feeds", "1"); google.setOnLoadCallback(load); </script> <div id="slideshow" class="gslideshow" style="width:300px;height:300px;position:relative; border: 2px solid blue">Loading...</div> When i execute the test.html, it loads the slideshow just fine. when i try to load using index.html that actually calls Jquery's $.load() function that loads the content of test.html into a specific div element, i see that the gallery is loading on that div, but when it's about to show images the entire page clears and all i have is a blank page. Any ideas ? a different version of index.html without using jquery: <script type="text/javascript"> function makeRequest(url) { var httpRequest; if (window.XMLHttpRequest) { // Mozilla, Safari, ... httpRequest = new XMLHttpRequest(); if (httpRequest.overrideMimeType) { httpRequest.overrideMimeType('text/xml'); // See note below about this line } } else if (window.ActiveXObject) { // IE try { httpRequest = new ActiveXObject("Msxml2.XMLHTTP"); } catch (e) { try { httpRequest = new ActiveXObject("Microsoft.XMLHTTP"); } catch (e) {} } } if (!httpRequest) { alert('Giving up :( Cannot create an XMLHTTP instance'); return false; } httpRequest.onreadystatechange = function() { alertContents(httpRequest); }; httpRequest.open('GET', url, true); httpRequest.send(''); } function alertContents(httpRequest) { if (httpRequest.readyState == 4) { if (httpRequest.status == 200) { document.getElementById('moshe').innerHTML=httpRequest.responseText; } else { alert('There was a problem with the request.'); } } } makeRequest('test.html'); </script>

    Read the article

  • How can I center XHTML content with CSS?

    - by drea
    so I recently converted a website of mine from a table content format to a div content format. Table format Version: Table version of the website: here. Table version style CSS: body { width: 1020px; margin: 0 auto; background-image: url(images/bg.png); } .logo{ width:301px; height:151px; background:url(images/logo.png); text-indent:-9999px; border:none; cursor:pointer; } .logo:hover { opacity:0.9; } .signin{ width:69px; height:30px; background:url(images/signin.png); text-indent:-9999px; border:none; cursor:pointer; } .signin:hover { opacity:0.9; } .register{ width:79px; height:30px; background:url(images/register.png); text-indent:-9999px; border:none; cursor:pointer; } .register:hover { opacity:0.9; } .Contact_Us{ width:53px; height:9px; background:url(images/Contact_Us.png); text-indent:-9999px; border:none; cursor:pointer; } .Contact_Us:hover { opacity:0.9; } .Code_of_Conduct{ width:84px; height:9px; background:url(images/Code_of_Conduct.png); text-indent:-9999px; border:none; cursor:pointer; } .Code_of_Conduct:hover { opacity:0.9; } .Privacy_Policy{ width:65px; height:12px; background:url(images/Privacy_Policy.png); text-indent:-9999px; border:none; cursor:pointer; } .Privacy_Policy:hover { opacity:0.9; } .Copyright{ width:149px; height:9px; background:url(images/Copyright.png); text-indent:-9999px; border:none; cursor:pointer; } .Copyright:hover { opacity:0.9; } .slideshow{ width:301px; height:151px; background: url(slideshow.png), url(minecraft.png), url(tf2.png), url(CSS.png), url(GM.png), url(aos.png), url(CSGO.png), url(voip.png), text-indent:-9999px; border:none; cursor:pointer; } .slideshow:hover { opacity:0.9; } Table version source: <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN" "http://www.w3.org/TR/html4/loose.dtd"> <html> <head profile="http://www.w3.org/2005/10/profile"> <link rel="icon" type="image/png" href="http://www.xodusen.com/resources/images/favicon.png"> <title>Welcome to XodusEN</title> <script type="text/javascript" src="https://ajax.googleapis.com/ajax/libs/jquery/1.8.0/jquery.min.js"></script> <script type="text/javascript" src="http://cloud.github.com/downloads/malsup/cycle/jquery.cycle.all.latest.js"></script> <script type="text/javascript"> $(document).ready(function() { $('.slideshow').cycle({ fx: 'fade' // choose your transition type, ex: fade, scrollUp, shuffle, etc... }); }); </script> <meta name="description" content="This is the homepage of XodusEN. Xodus Entertainment Network is a unique & friendly Gaming Community that welcomes & realises the potential, and value within any user regardless of their origin. " > <meta name="keywords" content="XeN, Xodus, XEN, xen, Xodus Entertainment Network, gaming, community, PC, Steam, XBL, Xbox 360, PSN, Playstation, games, Gaming, Community, XodusEN, Gaming Network, Network, TF2, Server, CS:S, Minecraft, premium, servers, Counter-Strike: Source, Website, Homepage, Minecraftia" > <meta http-equiv="Content-Type" content="text/html; charset=utf-8"> <link href="style.css" rel="stylesheet" type="text/css"> <!--[if IE]> <script type="text/javascript"> window.location = "http://www.xodusen.com/ie/"; </script> <![endif]--> </head> <body bgcolor="#d7d7d7"> <table id="Table_01" border="0" cellpadding="0" cellspacing="0"> <tr> <td colspan="18"> <img src="images/index_01.png" width="1020" height="9" alt=""></td> <td> <img src="images/spacer.gif" width="1" height="9" alt=""></td> </tr> <tr> <td colspan="11" rowspan="2"> <img src="images/index_02.png" width="826" height="252" alt=""></td> <td> <a id="signin" class="signin" href="http://s.xodusen.com/VrtqYm"> <img src="images/signin.png" width="69" height="30" border="0" alt=""></a> <td rowspan="6"> <img src="images/index_04.png" width="3" height="643" alt=""></td> <td colspan="3"> <a id="register" class="register" href="http://s.xodusen.com/WW3rpZ"> <img src="images/Register.png" width="79" height="30" border="0" alt=""></a> <td colspan="2" rowspan="6"> <img src="images/index_06.png" width="43" height="643" alt=""></td> <td> <img src="images/spacer.gif" width="1" height="30" alt=""></td> </tr> <tr> <td rowspan="5"> <img src="images/index_07.png" width="69" height="613" alt=""></td> <td colspan="3" rowspan="5"> <img src="images/index_08.png" width="79" height="613" alt=""></td> <td> <img src="images/spacer.gif" width="1" height="222" alt=""></td> </tr> <tr> <td colspan="5"> <img src="images/index_09.png" width="385" height="53" alt=""></td> <td> <img src="images/index_10.png" width="250" height="53" alt=""></td> <td colspan="5"> <img src="images/index_11.png" width="191" height="53" alt=""></td> <td> <img src="images/spacer.gif" width="1" height="53" alt=""></td> </tr> <tr> <td colspan="4" rowspan="3"> <img src="images/index_09-13.png" width="360" height="338" alt=""></td> <td colspan="3"> <a id="logo" class="logo" href="http://www.xodusen.com/community"> <img src="images/logo.png" alt=""></a> </td> <td colspan="4" rowspan="3"> <img src="images/index_11-15.png" width="165" height="338" alt=""></td> <td> <img src="images/spacer.gif" width="1" height="151" alt=""></td> </tr> <tr> <td rowspan="2"> <img src="images/index_09-16.png" width="25" height="187" alt=""></td> <td> <img src="images/index_16.png" width="250" height="46" alt=""></td> <td rowspan="2"> <img src="images/index_11-18.png" width="26" height="187" alt=""></td> <td> <img src="images/spacer.gif" width="1" height="46" alt=""></td> </tr> <tr> <td> <img src="images/index_12.png" width="250" height="141" alt=""></td> <td> <img src="images/spacer.gif" width="1" height="141" alt=""></td> </tr> <tr> <td rowspan="7"> <img src="images/index_13.png" width="27" height="548" alt=""></td> <td colspan="16" id="slideshow" class="slideshow"> <a href="http://www.xodusen.com/community"><img src="images/slideshow.png" width="960" height="305" alt=""></a> <a href="http://www.xodusen.com/mcurl"><img src="images/minecraft.png" width="960" height="305" alt=""></a> <a href="steam://connect/74.121.188.194:27015"><img src="images/tf2.png" width="960" height="305" alt=""></a> <a href="steam://connect/74.121.188.195:27015"><img src="images/CSS.png" width="960" height="305" alt=""></a> <a href="steam://connect/74.121.188.197:27015"><img src="images/GM.png" width="960" height="305" alt=""></a> <a href="aos://3267131722:32887"><img src="images/aos.png" width="960" height="305" alt=""></a> <a href="steam://connect/74.121.188.196:27015"><img src="images/CSGO.png" width="960" height="305" alt=""></a></td> <td rowspan="7"> <img src="images/index_15.png" width="33" height="548" alt=""></td> <td> <img src="images/spacer.gif" width="1" height="305" alt=""></td> </tr> <tr> <td colspan="16"> <img src="images/index_16-23.png" width="960" height="155" alt=""></td> <td> <img src="images/spacer.gif" width="1" height="155" alt=""></td> </tr> <tr> <td rowspan="5"> <img src="images/index_17.png" width="38" height="88" alt=""></td> <td rowspan="2"> <a id="Copyright" class="Copyright" href="http://www.xodusen.com/community"> <img src="images/Copyright.png" width="149" height="9" border="0" alt=""></a></td> <td colspan="14"> <img src="images/index_25.png" width="773" height="5" alt=""></td> <td> <img src="images/spacer.gif" width="1" height="5" alt=""></td> </tr> <tr> <td colspan="5" rowspan="4"> <img src="images/index_20.png" width="527" height="83" alt=""></td> <td rowspan="3"> <a id="Privacy_Policy" class="Privacy_Policy" href="http://s.xodusen.com/VhGEkH"> <img src="images/Privacy_Policy.png" width="65" height="12" border="0" alt=""></a></td> <td rowspan="4"> <img src="images/index_28.png" width="8" height="83" alt=""></td> <td colspan="3" rowspan="2"> <a id="Code_of_Conduct" class="Code_of_Conduct" href="http://s.xodusen.com/Tf5Gz7"> <img src="images/Code_of_Conduct.png" width="84" height="9" border="0" alt=""></a></td> <td rowspan="4"> <img src="images/index_30.png" width="6" height="83" alt=""></td> <td rowspan="2"> <a id="Contact_Us" class="Contact_Us" href="http://s.xodusen.com/T5EYsG"> <img src="images/Contact_Us.png" width="53" height="9" border="0" alt=""></a></td> <td colspan="2" rowspan="4"> <img src="images/index_26.png" width="30" height="83" alt=""></td> <td> <img src="images/spacer.gif" width="1" height="4" alt=""></td> </tr> <tr> <td rowspan="3"> <img src="images/index_27.png" width="149" height="79" alt=""></td> <td> <img src="images/spacer.gif" width="1" height="5" alt=""></td> </tr> <tr> <td colspan="3" rowspan="2"> <img src="images/index_28-35.png" width="84" height="74" alt=""></td> <td rowspan="2"> <img src="images/index_29.png" width="53" height="74" alt=""></td> <td> <img src="images/spacer.gif" width="1" height="3" alt=""></td> </tr> <tr> <td> <img src="images/index_30-37.png" width="65" height="71" alt=""></td> <td> <img src="images/spacer.gif" width="1" height="71" alt=""></td> </tr> <tr> <td> <img src="images/spacer.gif" width="27" height="1" alt=""></td> <td> <img src="images/spacer.gif" width="38" height="1" alt=""></td> <td> <img src="images/spacer.gif" width="149" height="1" alt=""></td> <td> <img src="images/spacer.gif" width="146" height="1" alt=""></td> <td> <img src="images/spacer.gif" width="25" height="1" alt=""></td> <td> <img src="images/spacer.gif" width="250" height="1" alt=""></td> <td> <img src="images/spacer.gif" width="26" height="1" alt=""></td> <td> <img src="images/spacer.gif" width="80" height="1" alt=""></td> <td> <img src="images/spacer.gif" width="65" height="1" alt=""></td> <td> <img src="images/spacer.gif" width="8" height="1" alt=""></td> <td> <img src="images/spacer.gif" width="12" height="1" alt=""></td> <td> <img src="images/spacer.gif" width="69" height="1" alt=""></td> <td> <img src="images/spacer.gif" width="3" height="1" alt=""></td> <td> <img src="images/spacer.gif" width="6" height="1" alt=""></td> <td> <img src="images/spacer.gif" width="53" height="1" alt=""></td> <td> <img src="images/spacer.gif" width="20" height="1" alt=""></td> <td> <img src="images/spacer.gif" width="10" height="1" alt=""></td> <td> <img src="images/spacer.gif" width="33" height="1" alt=""></td> <td></td> </tr> </table> </body> </html> Div format Version: Div version of the website: here. Div version style CSS: body { width: 1020px; margin: 0 auto; background-image: url(images/bg.png); } #Table_01 { position:absolute; left:0px; top:0px; width:1020px; height:1200px; } #index-01_ { position:absolute; left:0px; top:0px; width:1020px; height:9px; } #index-02_ { position:absolute; left:0px; top:9px; width:826px; height:305px; } #Signin_ { position:absolute; left:826px; top:9px; width:69px; height:30px; } #index-04_ { position:absolute; left:895px; top:9px; width:3px; height:643px; } #Register_ { position:absolute; left:898px; top:9px; width:79px; height:30px; } #index-06_ { position:absolute; left:977px; top:9px; width:43px; height:643px; } #index-07_ { position:absolute; left:826px; top:39px; width:69px; height:613px; } #index-08_ { position:absolute; left:898px; top:39px; width:79px; height:613px; } #index-09_ { position:absolute; left:0px; top:314px; width:360px; height:338px; } #Logo_ { position:absolute; left:360px; top:314px; width:301px; height:151px; } #index-11_ { position:absolute; left:661px; top:314px; width:165px; height:338px; } #index-12_ { position:absolute; left:360px; top:465px; width:301px; height:187px; } #index-13_ { position:absolute; left:0px; top:652px; width:27px; height:548px; } #Slideshow_ { position:absolute; left:27px; top:652px; width:960px; height:305px; } #index-15_ { position:absolute; left:987px; top:652px; width:33px; height:548px; } #index-16_ { position:absolute; left:27px; top:957px; width:960px; height:155px; } #index-17_ { position:absolute; left:27px; top:1112px; width:39px; height:88px; } #Copyright_ { position:absolute; left:66px; top:1112px; width:148px; height:13px; } #index-19_ { position:absolute; left:214px; top:1112px; width:773px; height:5px; } #index-20_ { position:absolute; left:214px; top:1117px; width:526px; height:83px; } #Privacy-Policy_ { position:absolute; left:740px; top:1117px; width:68px; height:23px; } #index-22_ { position:absolute; left:808px; top:1117px; width:6px; height:83px; } #Code-of-Conduct_ { position:absolute; left:814px; top:1117px; width:84px; height:23px; } #index-24_ { position:absolute; left:898px; top:1117px; width:2px; height:83px; } #Contact-Us_ { position:absolute; left:900px; top:1117px; width:57px; height:23px; } #index-26_ { position:absolute; left:957px; top:1117px; width:30px; height:83px; } #index-27_ { position:absolute; left:66px; top:1125px; width:148px; height:75px; } #index-28_ { position:absolute; left:740px; top:1140px; width:68px; height:60px; } #index-29_ { position:absolute; left:814px; top:1140px; width:84px; height:60px; } #index-30_ { position:absolute; left:900px; top:1140px; width:57px; height:60px; } .logo{ width:301px; height:151px; background:url(images/logo.png); text-indent:-9999px; border:none; cursor:pointer; } .logo:hover { opacity:0.9; } .signin{ width:69px; height:30px; background:url(images/signin.png); text-indent:-9999px; border:none; cursor:pointer; } .signin:hover { opacity:0.9; } .register{ width:79px; height:30px; background:url(images/register.png); text-indent:-9999px; border:none; cursor:pointer; } .register:hover { opacity:0.9; } .contact_Us{ width:53px; height:9px; background:url(images/Contact_Us.png); text-indent:-9999px; border:none; cursor:pointer; } .contact_Us:hover { opacity:0.9; } .code_of_Conduct{ width:84px; height:9px; background:url(images/Code_of_Conduct.png); text-indent:-9999px; border:none; cursor:pointer; } .code_of_Conduct:hover { opacity:0.9; } .privacy_policy{ width:65px; height:12px; background:url(images/Privacy_Policy.png); text-indent:-9999px; border:none; cursor:pointer; } .privacy_policy:hover { opacity:0.9; } .copyright{ width:148px; height:13px; background:url(images/Copyright.png); text-indent:-9999px; border:none; cursor:pointer; } .copyright:hover { opacity:0.9; } .slideshow{ width:301px; height:151px; background: url(slideshow.png), url(minecraft.png), url(tf2.png), url(CSS.png), url(GM.png), url(aos.png), url(CSGO.png), url(voip.png), text-indent:-9999px; border:none; cursor:pointer; } .slideshow:hover { opacity:0.9; } Div version source: <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="http://www.w3.org/1999/xhtml"> <head> <script type="text/javascript"> //<![CDATA[ window.__CF=window.__CF||{};window.__CF.AJS={"vig_key":{"sid":"c6d1454039dd49b1c8400bbfdf74df7a"},"trumpet":{"message":"XodusEN is undergoing background maintenance, that will provide performance & graphical improvements to our system, but will not hinder your experience across our services."},"ga_key":{"ua":"UA-35779435-1","ga_bs":"2"},"exprmntly":{"service_id":"7967"},"cdnjs":{"__h":"1","cdnjs":"MO,GF,FX,CS,JS"},"abetterbrowser":{"ie":"10"}}; //]]> </script> <script type="text/javascript"> //<![CDATA[ try{if (!window.CloudFlare) { var CloudFlare=[{verbose:0,p:0,byc:0,owlid:"cf",mirage:{responsive:0,lazy:0},oracle:0,paths:{cloudflare:"/cdn-cgi/nexp/aav=1870252173/"},atok:"d6e39f49946fcb6d690f0d10d5a963f3",zone:"xodusen.com",rocket:"a",apps:{"vig_key":{"sid":"c6d1454039dd49b1c8400bbfdf74df7a"},"trumpet":{"message":"XodusEN is undergoing background maintenance, that will provide performance & graphical improvements to our system, but will not hinder your experience across our services."},"ga_key":{"ua":"UA-35779435-1","ga_bs":"2"},"exprmntly":{"service_id":"7967"},"cdnjs":{"__h":"1","cdnjs":"MO,GF,FX,CS,JS"},"abetterbrowser":{"ie":"10"}}}];document.write('<script type="text/javascript" src="//ajax.cloudflare.com/cdn-cgi/nexp/aav=4114775854/cloudflare.min.js"><'+'\/script>')}}catch(e){}; //]]> </script> <script type="text/javascript" src="//ajax.cloudflare.com/cdn-cgi/nexp/aav=1566821048/appsh.min.js"></script><script type="text/javascript">__CF.AJS.inith();</script><link rel="icon" type="image/png" href="http://www.xodusen.com/resources/images/favicon.png"> <title>Welcome to XodusEN</title> <meta name="description" content="This is the homepage of XodusEN. Xodus Entertainment Network is a unique & friendly Gaming Community that welcomes & realises the potential, and value within any user regardless of their origin. "> <meta name="keywords" content="XeN, Xodus, XEN, xen, Xodus Entertainment Network, gaming, community, PC, Steam, XBL, Xbox 360, PSN, Playstation, games, Gaming, Community, XodusEN, Gaming Network, Network, TF2, Server, CS:S, Minecraft, premium, servers, Counter-Strike: Source, Website, Homepage, Minecraftia"> <meta http-equiv="Content-Type" content="text/html; charset=utf-8"/> <link href="style.css" rel="stylesheet" type="text/css"> <script type="text/rocketscript" data-rocketsrc="https://ajax.googleapis.com/ajax/libs/jquery/1.8.0/jquery.min.js"></script> <script type="text/rocketscript" data-rocketsrc="http://cloud.github.com/downloads/malsup/cycle/jquery.cycle.all.latest.js"></script> <script type="text/rocketscript"> $(document).ready(function() { $('.slideshow').cycle({ fx: 'fade' // choose your transition type, ex: fade, scrollUp, shuffle, etc... }); }); </script> <!--[if IE]> <script type="text/javascript"> window.location = "http://www.xodusen.com/ie/"; </script> <![endif]--> <script type="text/javascript"> /* <![CDATA[ */ var _gaq = _gaq || []; _gaq.push(['_setAccount', 'UA-35779435-1']); _gaq.push(['_trackPageview']); (function() { var ga = document.createElement('script'); ga.type = 'text/javascript'; ga.async = true; ga.src = ('https:' == document.location.protocol ? 'https://ssl' : 'http://www') + '.google-analytics.com/ga.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(ga, s); })(); (function(b){(function(a){"__CF"in b&&"DJS"in b.__CF?b.__CF.DJS.push(a):"addEventListener"in b?b.addEventListener("load",a,!1):b.attachEvent("onload",a)})(function(){"FB"in b&&"Event"in FB&&"subscribe"in FB.Event&&(FB.Event.subscribe("edge.create",function(a){_gaq.push(["_trackSocial","facebook","like",a])}),FB.Event.subscribe("edge.remove",function(a){_gaq.push(["_trackSocial","facebook","unlike",a])}),FB.Event.subscribe("message.send",function(a){_gaq.push(["_trackSocial","facebook","send",a])}));"twttr"in b&&"events"in twttr&&"bind"in twttr.events&&twttr.events.bind("tweet",function(a){if(a){var b;if(a.target&&a.target.nodeName=="IFRAME")a:{if(a=a.target.src){a=a.split("#")[0].match(/[^?=&]+=([^&]*)?/g);b=0;for(var c;c=a[b];++b)if(c.indexOf("url")===0){b=unescape(c.split("=")[1]);break a}}b=void 0}_gaq.push(["_trackSocial","twitter","tweet",b])}})})})(window); /* ]]> */ </script> <meta name="pinterest" content="nopin"/></head> <body style="background-color:#d7d7d7;"><script type="text/javascript"> //<![CDATA[ try{(function(a){var b="http://",c="www.xodusen.com",d="/cdn-cgi/cl/",e="618e40fe1e01787d9cb9aa2f8abc52caf8a32796.gif",f=new a;f.src=[b,c,d,e].join("")})(Image)}catch(e){} //]]> </script> <div id="Table_01"> <div id="index-01_"> <img id="index_01" src="images/index_01.png" width="1020" height="9" alt=""/> </div> <div id="index-02_"> <img id="index_02" src="images/index_02.png" width="826" height="305" alt=""/> </div> <div id="Signin_"> <a href="http://s.xodusen.com/VrtqYm"> <img id="Signin" class="signin" src="images/Signin.png" width="69" height="30" border="0" alt=""/></a> </div> <div id="index-04_"> <img id="index_04" src="images/index_04.png" width="3" height="643" alt=""/> </div> <div id="Register_"> <a href="http://s.xodusen.com/WW3rpZ"> <img id="Register" class="register" src="images/Register.png" width="79" height="30" alt=""/></a> </div> <div id="index-06_"> <img id="index_06" src="images/index_06.png" width="43" height="643" alt=""/> </div> <div id="index-07_"> <img id="index_07" src="images/index_07.png" width="69" height="613" alt=""/> </div> <div id="index-08_"> <img id="index_08" src="images/index_08.png" width="79" height="613" alt=""/> </div> <div id="index-09_"> <img id="index_09" src="images/index_09.png" width="360" height="338" alt=""/> </div> <div id="Logo_"> <a href="http://s.xodusen.com/WW3rpZ"> <img class="logo" src="images/Logo.png" width="301" height="151" alt=""></a> </div> <div id="index-11_"> <img id="index_11" src="images/index_11.png" width="165" height="338" alt=""/> </div> <div id="index-12_"> <img id="index_12" src="images/index_12.png" width="301" height="187" alt=""/> </div> <div id="index-13_"> <img id="index_13" src="images/index_13.png" width="27" height="548" alt=""/> </div> <div id="Slideshow_" class="slideshow"> <a href="http://www.xodusen.com/community"> <img src="images/slideshow.png" width="960" height="305" alt=""></a> <a href="http://www.xodusen.com/mcurl"> <img src="images/minecraft.png" width="960" height="305" alt=""></a> <a href="steam://connect/74.121.188.194:27015"> <img src="images/tf2.png" width="960" height="305" alt=""></a> <a href="steam://connect/74.121.188.195:27015"> <img src="images/CSS.png" width="960" height="305" alt=""></a> <a href="steam://connect/74.121.188.197:27015"> <img src="images/GM.png" width="960" height="305" alt=""></a> <a href="aos://3267131722:32887"> <img src="images/aos.png" width="960" height="305" alt=""></a> <a href="steam://connect/74.121.188.196:27015"> <img src="images/CSGO.png" width="960" height="305" alt=""></a> </div> <div id="index-15_"> <img id="index_15" src="images/index_15.png" width="33" height="548" alt=""/> </div> <div id="index-16_"> <img id="index_16" src="images/index_16.png" width="960" height="155" alt=""/> </div> <div id="index-17_"> <img id="index_17" src="images/index_17.png" width="39" height="88" alt=""/> </div> <div id="Copyright_"> <a href="http://www.xodusen.com/community"> <img id="Copyright" src="images/Copyright.png" width="148" height="13" alt=""></a> </div> <div id="index-19_"> <img id="index_19" src="images/index_19.png" width="773" height="5" alt=""/> </div> <div id="index-20_"> <img id="index_20" src="images/index_20.png" width="526" height="83" alt=""/> </div> <div id="Privacy-Policy_"> <a href="http://s.xodusen.com/VhGEkH"> <img id="Privacy_Policy" src="images/Privacy_Policy.png" width="68" height="23" alt=""></a> </div> <div id="index-22_"> <img id="index_22" src="images/index_22.png" width="6" height="83" alt=""/> </div> <div id="Code-of-Conduct_"> <a href="http://s.xodusen.com/Tf5Gz7"> <img id="Code_of_Conduct" src="images/Code_of_Conduct.png" width="84" height="23" alt=""></a> </div> <div id="index-24_"> <img id="index_24" src="images/index_24.png" width="2" height="83" alt=""/> </div> <div id="Contact-Us_"> <a href="http://s.xodusen.com/T5EYsG"> <img id="Contact_Us" src="images/Contact_Us.png" width="57" height="23" alt=""></a> </div> <div id="index-26_"> <img id="index_26" src="images/index_26.png" width="30" height="83" alt=""/> </div> <div id="index-27_"> <img id="index_27" src="images/index_27.png" width="148" height="75" alt=""/> </div> <div id="index-28_"> <img id="index_28" src="images/index_28.png" width="68" height="60" alt=""/> </div> <div id="index-29_"> <img id="index_29" src="images/index_29.png" width="84" height="60" alt=""/> </div> <div id="index-30_"> <img id="index_30" src="images/index_30.png" width="57" height="60" alt=""/> </div> </div> <script type="text/javascript" src="//ajax.cloudflare.com/cdn-cgi/nexp/aav=4188748942/apps1.min.js"></script><script type="text/javascript">__CF.AJS.init1();</script></body> </html> My issue is, how can I achieve the same 'centered' results in the div format of the website, as the table format of the website? I have done some research to no avail, so I'd thought given the reputation of this site, that i'd post my issue here. Thank you in advance, ~ drea.

    Read the article

  • postfix relaying all mail through office365 problems

    - by amrith
    This is a rather long question with a long list of things tried and travails so please bear with me. The summary is this. I am able to relay email from ubuntu through office365 using postfix; the configuration works. It only works as one of the users; more specifically the user who authenticates against office365 is the only valid "from" More details follow. I have a machine in Amazon's cloud on which I run a bunch of jobs and would like to have statuses mailed over to me. I use office365 at work so I want to relay mail through office365. I'm most familiar with postfix so I used that as the MTA. Configuration is ubuntu 12.04LTS; I've installed postfix and mail-utils. For this example, let me say my company is "company.com" and the machine in question (through an elastic IP and a DNS entry) is called "plaything.company.com". hostname is set to "plaything.company.com", so is /etc/mailname On plaything, I have the following users registered alpha, bravo, and charlie. I have the following configuration files. alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no config_directory = /etc/postfix inet_interfaces = all inet_protocols = ipv4 mailbox_size_limit = 0 mydestination = plaything.company.com, localhost.company.com, , localhost myhostname = plaything.company.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 myorigin = /etc/mailname readme_directory = no recipient_delimiter = + relayhost = [smtp.office365.com]:587 sender_canonical_maps = hash:/etc/postfix/sender_canonical smtp_sasl_auth_enable = yes smtp_sasl_password_maps = hash:/etc/postfix/sasl_passwd smtp_sasl_security_options = noanonymous smtp_sasl_tls_security_options = noanonymous smtp_tls_CAfile = /etc/ssl/certs/ca-certificates.crt smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes As the machine is called plaything.company.com I went through the exercise of registering all the appropriate DNS entries to make office365 recognize that I owned plaything.company.com and allowed me to create a user called [email protected] in office365. In office365, I setup [email protected] as having another email address of [email protected]. Then, I made the following sender_canonical [email protected] [email protected] I created a sasl_passwd file that reads: smtp.office365.com [email protected]:123456password123456 let's just say that the password for [email protected] is 1234...456 With all this setup, login as alpha and mail [email protected] Cc: Subject: test test and the whole thing works wonderfully. email gets sent off by postfix, TLS works like a champ, authenticates as daemon@... and [email protected] in Office365 gets an email message. The issue comes up when logged in as bravo to the machine. sender is [email protected] and office365 says: status=bounced (host smtp.office365.com[132.245.12.25] said: 550 5.7.1 Client does not have permissions to send as this sender (in reply to end of DATA command)) this is because I'm trying to send mail as bravo@... and authenticating with office365 as daemon@.... The reason it works with alpha@... is because in office365, I setup [email protected] as having another email address of [email protected]. In Postfix Relay to Office365, Miles Erickson answers the question thusly: Don't send mail to Office365 as a user from your Office365-hosted e-mail domain. Use a subdomain instead, e.g. [email protected] instead of [email protected]. It wouldn't hurt to set up an SPF record for services.mydomain.com or whatever you decide to use. Don't authenticate against mail.messaging.microsoft.com as an Office365 user. Just connect on port 25 and deliver the mail to your domain as any foreign SMTP agent would do. OK, I've done #1, I have those records on DNS but for the most part they are not relevant once Office365 recognizes that I own the domain. Here are those records: CNAME records: - msoid.plaything.company.com - autodiscover.plaything.company.com MX record: - plaything.company.com (plaything-company-com.mail.protection.outlook.com) TXT record: - plaything.company.com (v=spf1 include:spf.protection.outlook.com -all) I've tried #2 but no matter what I do, office365 just blows away the connection with "not authenticated". I can try even a simple telnet to port 25 and attempt to send and it doesn't work. 250 BY2PR01CA007.outlook.office365.com Hello [54.221.245.236] 530 5.7.1 Client was not authenticated Connection closed by foreign host. Is there someone out there who has this kind of a configuration working where multiple users on a linux machine are able to relay mail using postfix through office365? There has to be someone out there doing this who can tell me what is wrong with my setup ...

    Read the article

  • Server side Xforms form validation and integration into ASP.NET

    - by Nigel
    I have recently been investigating methods of creating web-based forms for an ASP.NET web application that can be edited and managed at runtime. For example an administrator might wish to add a new validation rule or a new set of fields. The holy grail would provide a means of specifying a form along with (potentially very complex) arbitrary validation rules, and allocation of data sources for each field. The specification would then be used to update the deployed form in the web application which would then validate submissions both on the client side and on the server side. My investigations led me to Xforms and a number of technologies that support it. One solution appears to be IBM Lotus Forms, but this requires a very large investment in terms of infrastructure, which makes it infeasible, although the forms designer may be useful as a stand-alone tool for creating the forms. I have also discounted browser plug-ins as the form must be publicly visible and cross-browser compliant. I have noticed that there are numerous javascript libraries that provide client side implementations given an Xforms schema. These would provide a partial solution but server side validation is still a requirement. Another option seems to involve the use of server side solutions such as the Java application Orbeon. Orbeon provides a tool for specifying the forms (although not as rich as Lotus Forms Designer), but the most interesting point is that it can translate an XForms schema into an XHTML form complete with validation. The fact that it is written in Java is not a big problem if it is possible to integrate with the existing ASP.NET application. So my question is whether anyone has done this before. It sounds like a problem that should have been solved but is inherently very complex. It seems possible to use an off-the-shelf tool to design the form and export it to an Xforms schema and xhtml form, and it seems possible to take that xforms schema and form and publish it using a client side library. What seems to be difficult is providing a means of validating the form submission on the server side and integrating the process nicely with .NET (although it seems the .NET community doesn't involve themselves with XForms; please correct me if I'm wrong on this count). I would be more than happy if a product provided something simple like a web service that could validate a submission against a schema. Maybe Orbeon does this but I'd be grateful if somebody in the know could point me in the right direction before I research it further. Many thanks.

    Read the article

  • multiple stateful iframes per page will overwrite JSESSIONID?

    - by Nikita
    Hello, Looking for someone to either confirm or refute my theory that deploying two iframes pointing to two different stateful pages on the same domain can lead to JSESSIONIDs being overwritten. Here's what I mean: Setup suppose you have two pages that require HttpSession state (session affinity) to function correctly - deployed at http://www.foo.com/page1 and http://www.foo.com/page2 assume www.foo.com is a single host running a Tomcat (6.0.20, fwiw) that uses JSESSIONID for session id's. suppose these pages are turned into two iframe widgets to be embedded on 3rd party sites: http://www.site.com/page1" / (and /page2 respectively) suppose there a 3rd party site that wishes to place both widgets on the same page at http://www.bar.com/foowidgets.html Can the following race condition occur? a new visitor goes to http://www.bar.com/foowidgets.html browser starts loading URLs in foowidgets.html including the two iframe 'src' URLs because browsers open multiple concurrent connections against the same host (afaik up to 6 in chrome/ff case) the browser happens to simultaneously issue requests for http://www.foo.com/page1 and http://www.foo.com/page2 The tomcat @ foo.com receives both requests at about the same time, calls getSession() for the first time (on two different threads) and lazily creates two HttpSessions and, thus, two JSESSIONIDs, with values $Page1 and $Page2. The requests also stuff data into respective sessions (that data will be required to process subsequent requests) assume that the browser first receives response to the page1 request. Browser sets cookie JSESSIONID=$Page1 for HOST www.foo.com next response to the page2 request is received and the browser overwrites cookie JSESSIONID for HOST www.foo.com with $Page2 user clicks on something in 'page1' iframe on foowidgets.html; browser issues 2nd request to http://www.foo.com/page1?action=doSomethingStateful. That request carries JSESSIONID=$Page2 (and not $Page1 - because cookie value was overwritten) when foo.com receives this request it looks up the wrong HttpSession instance (because JSESSIONID key is $Page2 and NOT $Page1). Foobar! Can the above happen? I think so, but would appreciate a confirmation. If the above is clearly possible, what are some solutions given that we'd like to support multiple iframes per page? We don't have a firm need for the iframes to share the same HttpSession, though that would be nice. In the event that the solution will still stipulate a separate HttpSession per iframe, it is - of course - mandatory that iframe 1 does not end up referencing httpSession state for iframe 2 instead of own. off top of my head I can think of: map page1 and page2 to different domains (ops overhead) use URL rewriting and never cookies (messes up analytics) anything else? thanks a lot, -nikita

    Read the article

  • Mouse wheel not scrolling in JDialog but working in JFrame

    - by Iulian Serbanoiu
    Hello, I'm facing a frustrating issue. I have an application where the scroll wheel doesn't work in a JDialog window (but works in a JFrame). Here's the code: import javax.swing.*; import java.awt.event.*; public class Failtest extends JFrame { public static void main(String[] args) { new Failtest(); } public Failtest() { super(); setDefaultCloseOperation(JFrame.DISPOSE_ON_CLOSE); setTitle("FRAME"); JScrollPane sp1 = new JScrollPane(getNewList()); add(sp1); setSize(150, 150); setVisible(true); JDialog d = new JDialog(this, false);// NOT WORKING //JDialog d = new JDialog((JFrame)null, false); // NOT WORKING //JDialog d = new JDialog((JDialog)null, false);// WORKING - WHY? d.setTitle("DIALOG"); d.setDefaultCloseOperation(JDialog.DISPOSE_ON_CLOSE); JScrollPane sp = new JScrollPane(getNewList()); d.add(sp); d.setSize(150, 150); d.setVisible(true); } public JList getNewList() { String objs[] = new String[30]; for(int i=0; i<objs.length; i++) { objs[i] = "Item "+i; } JList l = new JList(objs); return l; } } I found a solution which is present as a comment in the java code - the constructor receiving a (JDialog)null parameter. Can someone enlighten me? My opinion is that this is a java bug. Tested on Windows XP-SP3 with 1 JDK and 2 JREs: D:\Program Files\Java\jdk1.6.0_17\bin>javac -version javac 1.6.0_17 D:\Program Files\Java\jdk1.6.0_17\bin>java -version java version "1.6.0_17" Java(TM) SE Runtime Environment (build 1.6.0_17-b04) Java HotSpot(TM) Client VM (build 14.3-b01, mixed mode, sharing) D:\Program Files\Java\jdk1.6.0_17\bin>cd .. D:\Program Files\Java\jdk1.6.0_17>java -version java version "1.6.0_18" Java(TM) SE Runtime Environment (build 1.6.0_18-b07) Java HotSpot(TM) Client VM (build 16.0-b13, mixed mode, sharing) Thank you in advance, Iulian Serbanoiu PS: The problem is not new - the code is taken from a forum (here) where this problem was also mentioned - but no solutions to it (yet) LATER EDIT: The problem persists with jre/jdk_1.6.0_10, 1.6.0_16 also LATER EDIT 2: Back home, tested on linux (Ubuntu - lucid/lynx) - both with openjdk and sun-java from distribution repo and it works (I used the .class file compiled on Windows) !!! - so I believe I'm facing a JRE bug that happens on some Windows configurations.

    Read the article

  • Is MVVM pointless?

    - by joebeazelman
    Is orthodox MVVM implementation pointless? I am creating a new application and I considered Windows Forms and WPF. I chose WPF because it's future-proof and offer lots of flexibility. There is less code and easier to make significant changes to your UI using XAML. Since the choice for WPF is obvious, I figured that I may as well go all the way by using MVVM as my application architecture since it offers blendability, separation concerns and unit testability. Theoretically, it seems beautiful like the holy grail of UI programming. This brief adventure; however, has turned into a real headache. As expected in practice, I’m finding that I’ve traded one problem for another. I tend to be an obsessive programmer in that I want to do things the right way so that I can get the right results and possibly become a better programmer. The MVVM pattern just flunked my test on productivity and has just turned into a big yucky hack! The clear case in point is adding support for a Modal dialog box. The correct way is to put up a dialog box and tie it to a view model. Getting this to work is difficult. In order to benefit from the MVVM pattern, you have to distribute code in several places throughout the layers of your application. You also have to use esoteric programming constructs like templates and lamba expressions. Stuff that makes you stare at the screen scratching your head. This makes maintenance and debugging a nightmare waiting to happen as I recently discovered. I had an about box working fine until I got an exception the second time I invoked it, saying that it couldn’t show the dialog box again once it is closed. I had to add an event handler for the close functionality to the dialog window, another one in the IDialogView implementation of it and finally another in the IDialogViewModel. I thought MVVM would save us from such extravagant hackery! There are several folks out there with competing solutions to this problem and they are all hacks and don’t provide a clean, easily reusable, elegant solution. Most of the MVVM toolkits gloss over dialogs and when they do address them, they are just alert boxes that don’t require custom interfaces or view models. I’m planning on giving up on the MVVM view pattern, at least its orthodox implementation of it. What do you think? Has it been worth the trouble for you if you had any? Am I just a incompetent programmer or does MVVM not what it's hyped up to be?

    Read the article

  • Seeking for faster $.(':data(key)')

    - by PoltoS
    I'm writing an extension to jQuery that adds data to DOM elements using el.data('lalala', my_data); and then uses that data to upload elements dynamically. Each time I get new data from the server I need to update all elements having el.data('lalala') != null; To get all needed elements I use an extension by James Padolsey: $(':data(lalala)').each(...); Everything was great until I came to the situation where I need to run that code 50 times - it is very slow! It takes about 8 seconds to execute on my page with 3640 DOM elements var x, t = (new Date).getTime(); for (n=0; n < 50; n++) { jQuery(':data(lalala)').each(function() { x++; }); }; console.log(((new Date).getTime()-t)/1000); Since I don't need RegExp as parameter of :data selector I've tried to replace this by var x, t = (new Date).getTime(); for (n=0; n < 50; n++) { jQuery('*').each(function() { if ($(this).data('lalala')) x++; }); }; console.log(((new Date).getTime()-t)/1000); This code is faster (5 sec), but I want get more. Q Are there any faster way to get all elements with this data key? In fact, I can keep an array with all elements I need, since I execute .data('key') in my module. Checking 100 elements having the desired .data('lalala') is better then checking 3640 :) So the solution would be like for (i in elements) { el = elements[i]; .... But sometimes elements are removed from the page (using jQuery .remove()). Both solutions described above [$(':data(lalala)') solution and if ($(this).data('lalala'))] will skip removed items (as I need), while the solution with array will still point to removed element (in fact, the element would not be really deleted - it will only be deleted from the DOM tree - because my array will still have a reference). I found that .remove() also removes data from the node, so my solution will change into var toRemove = []; for (vari in elements) { var el = elements[i]; if ($(el).data('lalala')) .... else toRemove.push(i); }; for (var ii in toRemove) elements.splice(toRemove[ii], 1); // remove element from array This solution is 100 times faster! Q Will the garbage collector release memory taken by DOM elements when deleted from that array? Remember, elements have been referenced by DOM tree, we made a new reference in our array, then removed with .remove() and then removed from the array. Is there a better way to do this?

    Read the article

  • html widget communicating with server

    - by Nikita Rybak
    I'm making html widget for websites. Let's say, it will display current stock indexes. In short, arbitrary website owner takes code snippet from me and includes it on his webpage http://website.com/index.html. When arbitrary user opens http://website.com/index.html, my code sends request to my server (provider.com), which performs necessary operations and returns information to user's browser. When response has arrived, user will see relevant stock value on http://website.com/index.html. In index.html service could be called like this <script type="text/javascript" src="provider.com/service.js"> </script> <div id="target_area"></div> <script type="text/javascript"> service.show("target_area", options); </script> Now, the problem is in the same origin policy: I can't just send ajax request from website.com to provided.com and return html to embed in client's webpage. I see several solutions, which I list below, but none quite satisfy me. I wonder, if you could suggest something, especially if you had some relevant experience. 1) iframe, plain and simple. Disadvantage: must have fixed dimensions + stupid scroll bars appearing in some browsers. Can be fixed with javascript, but all this browser-specific tinkering doesn't sound good to me. 2) JSONP. Problem: can't return whole chunk of html, must return only data. Then, on browser side, I'll have to use javascript to embed data into html snippet placed statically in index.html. Doesn't sound nice, because data format is not very simple and may even change later. 3) Use hidden iframe to do ajax requests. A bit tricky, but sounds like a way to go. Well, that's my thoughts on the subject. Are there any better ways? BTW, I tried to check some existing widgets too, but didn't find much useful information. All domain names used in this text are fictional and any resemblance is purely coincidental :)

    Read the article

  • Another design-related C++ question

    - by Kotti
    Hi! I am trying to find some optimal solutions in C++ coding patterns, and this is one of my game engine - related questions. Take a look at the game object declaration (I removed almost everything, that has no connection with the question). // Abstract representation of a game object class Object : public Entity, IRenderable, ISerializable { // Object parameters // Other not really important stuff public: // @note Rendering template will never change while // the object 'lives' Object(RenderTemplate& render_template, /* params */) : /*...*/ { } private: // Object rendering template RenderTemplate render_template; public: /** * Default object render method * Draws rendering template data at (X, Y) with (Width, Height) dimensions * * @note If no appropriate rendering method overload is specified * for any derived class, this method is called * * @param Backend & b * @return void * @see */ virtual void Render(Backend& backend) const { // Render sprite from object's // rendering template structure backend.RenderFromTemplate( render_template, x, y, width, height ); } }; Here is also the IRenderable interface declaration: // Objects that can be rendered interface IRenderable { /** * Abstract method to render current object * * @param Backend & b * @return void * @see */ virtual void Render(Backend& b) const = 0; } and a sample of a real object that is derived from Object (with severe simplifications :) // Ball object class Ball : public Object { // Ball params public: virtual void Render(Backend& b) const { b.RenderEllipse(/*params*/); } }; What I wanted to get is the ability to have some sort of standard function, that would draw sprite for an object (this is Object::Render) if there is no appropriate overload. So, one can have objects without Render(...) method, and if you try to render them, this default sprite-rendering stuff is invoked. And, one can have specialized objects, that define their own way of being rendered. I think, this way of doing things is quite good, but what I can't figure out - is there any way to split the objects' "normal" methods (like Resize(...) or Rotate(...)) implementation from their rendering implementation? Because if everything is done the way described earlier, a common .cpp file, that implements any type of object would generally mix the Resize(...), etc methods implementation and this virtual Render(...) method and this seems to be a mess. I actually want to have rendering procedures for the objects in one place and their "logic implementation" - in another. Is there a way this can be done (maybe alternative pattern or trick or hint) or this is where all this polymorphic and virtual stuff sucks in terms of code placement?

    Read the article

  • ASP.Net MVC Exception Logging combined with Error Handling

    - by Saajid Ismail
    Hi. I am looking for a simple solution to do Exception Logging combined with Error Handling in my ASP.Net MVC 1.0 application. I've read lots of articles, including Questions posted here on StackOverflow, which all provide varying solutions for different situations. I am still unable to come up with a solution that suits my needs. Here are my requirements: To be able to use the [HandleError] attribute (or something equivalent) on my Controller, to handle all exceptions that could be thrown from any of the Actions or Views. This should handle all exceptions that were not handled specifically on any of the Actions (as described in point 2). I would like to be able to specify which View a user must be redirected to in error cases, for all actions in the Controller. I want to be able to specify the [HandleError] attribute (or something equivalent) at the top of specific Actions to catch specific exceptions and redirect users to a View appropriate to the exception. All other exceptions must still be handled by the [HandleError] attribute on the Controller. In both cases above, I want the exceptions to be logged using log4net (or any other logging library). How do I go about achieving the above? I've read about making all my Controllers inherit from a base controller which overrides the OnException method, and wherein I do my logging. However this will mess around with redirecting users to the appropriate Views, or make it messy. I've read about writing my own Filter Action which implements IExceptionFilter to handle this, but this will conflict with the [HandleError] attribute. So far, my thoughts are that the best solution is to write my own attribute that inherits from HandleErrorAttribute. That way I get all the functionality of [HandleError], and can add my own log4net logging. The solution is as follows: public class HandleErrorsAttribute: HandleErrorAttribute { private log4net.ILog log = log4net.LogManager.GetLogger(System.Reflection.MethodBase.GetCurrentMethod().DeclaringType); public override void OnException(ExceptionContext filterContext) { if (filterContext.Exception != null) { log.Error("Error in Controller", filterContext.Exception); } base.OnException(filterContext); } } Will the above code work for my requirements? If not, what solution does fulfill my requirements?

    Read the article

  • How can we implement change notification propagation for WPF and SL in the MVVM pattern?

    - by Firoso
    Here's an example scenario targetting MVVM WPF/SL development: View data binds to view model Property "Target" "Target" exposes a field of an object called "data" that exists in the local application model, called "Original" when "Original" changes, it should raise notification to the view model and then propogate that change notification to the View. Here are the solutions I've come up with, but I don't like any of them all that much. I'm looking for other ideas, by the time we come up with something rock solid I'm certain Microsoft will have released .NET 5 with WPF/SL extensions for better tools for MVVM development. For now the question is, "What have you done to solve this problem and how has it worked out for you?" Option 1. Proposal: Attach a handler to data's PropertyChanged event that watches for string values of properties it cares about that might have changed, and raises the appropriate notification. Why I don't like it: Changes don't bubble naturally, objects must be explicitly watched, if data changes to a new source, events must be un-registered/registered. Why I kind of like it: I get explicit control over propogation of changes, and I don't have to use any types that belong at a higher level of the application such as dependancy properties. Option 2. Proposal: Attach a handler to data's PropertyChanged event that re-raises the event across all properties using the name property name. Why I don't like it: This is essentially the same as option 1, but less intelligent, and forces me to never change my property names, as they have to be the same as the property names on data Why I kind of like it: It's very easy to set up and I don't have to think about it... Then again if I try to think, and change names to things that make sense, I shoot myself in the foot, and then I have to think about it! Option 3. Proposal: Inherit my view model from dependancy object, and notify binding sources of changes directly. Why I don't like it: I'm not even 100% sure dependancy properties/objects can DO this, it was just a thought to look into. Also I don't personally feel that WPF/SL types like Dep Obj belong at the view model level. Why I kind of like it: IF it has the capability that I'm seeking then it's a good answer! minus that pesky layering issue. Option 4. Proposal: Use a consistant agent messaging system based off of Task Parallels DataFlow Library to propogate everything through linked pipelining. Why I don't like it: I've never tried this, and somehow I think it will be lacking, plus it requires me to think about my code completely differently all the way around. Why I kind of like it: It has the possiblity of allowing me to do some VERY fun manipulations with a push based data model and using ActionBlocks as validation AND setters to then privately change view model properties and explicitly control PropertyChanged notifications.

    Read the article

  • Reproduce PIPE functionality in IronPython

    - by Muppet Geoff
    Hi, I am hoping some genious out there can help me out with this... I am using sox to merge and resample a group of WAV files, and pipe the output directly to the input of NeroAACEnc for encoding to AAC format. I originally ran the process in a script, which included: sox.exe d:\audio\1.wav d:\audio\2.wav d:\audio\3.wav -c 1 -r 22050 -t wav - | neroAacEnc.exe -q 0.5 -if - -of test.m4a This worked as expected. The '-' in the comand line translates as 'Pipe/redirect input/output (stdin/stdout)' - So Sox pipes to stdout, and NeroAACEnc reads from stdin, the | joins them together. I then migrated the whole solution to Python, and the equivalent command became: from subprocess import call, Popen, PIPE runwav = Popen(['sox.exe', 'd:\audio\1.wav', 'd:\audio\2.wav', 'd:\audio\3.wav', '-c', '1', '-r', '22050', '-t', 'wav', '-'], shell=False, stdout=PIPE) runm4b = call(['neroAacEnc.exe', '-q', '0.5', '-if', '-', '-of', 'test.m4a'], shell=False, stdin=runwav.stdout) This also worked like a charm, exactly as expected. Slightly more convoluted, but hey :) Well now I have to move it to IronPython, and the Subprocess module isn't available (the partial implementation that is, doesn't have Popen/PIPE support - plus it seems silly to add a custom library when there is probably a native alternative). I should mention here, that I opted for IronPython over C#, because I am comfortable with Python now - however, there is a chance of moving it again later to C# native, and I am using IronPython to ease myself into it :) I have no C# or .net experience. So far I have the following equivalent, that sets up the 2 processes: from System.Diagnostics import Process wav = Process() wav.StartInfo.UseShellExecute = False wav.StartInfo.RedirectStandardOutput = True wav.StartInfo.FileName = 'sox.exe' wav.StartInfo.Arguments = 'd:\audio\1.wav d:\audio\2.wav d:\audio\3.wav -c 1 -r 22050 -t wav -' wav.Start() m4b = Process() m4b.StartInfo.UseShellExecute = False m4b.StartInfo.RedirectStandardInput = True m4b.StartInfo.FileName = 'neroAacEnc.exe' m4b.StartInfo.Arguments = '-q 0.5 -if - -of test.m4a' m4b.Start() I know that these 2 processes start (I can see Nero and Sox in the task manager) but what I can't figure out (for the life of me) is how to string the two output/input streams together, as with the previous two solutions. I have searched and searched, so I thought I'd ask! If anyone knows either: How to join the two streams with the same net result as the Python and Commandline versions; or A better way to acheive what I am trying to do. I would be extremely grateful! Many thanks in advance, Geoff P.S. A code sample based off the above would be awesome :) or a specific code example of a similar process that I can easily translate... this has broked my brayne.

    Read the article

  • JSF Navigation issue Facelets and Beans

    - by ortho
    Hi, I have an issue with navigation in my simple jsf system. I have MainBean that has two methods: public String register() and public String login(). I have played with faces-config.xml for several hours and I feel like I miss something very important because I think like I have tried all simple solutions so far :). I have added the mysql connector (jdbc) to Tomcat's lib folder and I am able to register the table to mySQL databse. It even allows my users to log in to the page. The only problem is that I can't use navigation in any other page than login.xhtml. Seems like navigation is only active on this one. I tried to use * but is no joy. I am sure that there is a simple fix for that and someone will come up with correct solution soon. Let's skip all the mysql part and try to fix the navigation issue please. faces-config.xml: http://java.sun.com/xml/ns/javaee/web-facesconfig_1_2.xsd" version="1.2" com.sun.facelets.FaceletViewHandler mainBean dk.itu.beans.MainBean session registerBean dk.itu.beans.RegisterBean session /login.xhtml success /welcome.xhtml failure /login_failed.xhtml sign /register.xhtml /login_failed.xhtml back /login.xhtml Here the last navigation-rule from login_failed.xhtml does not work at all. login.xhtml (which is the main - starting view): login_failed.xhtml: Here I tried many options. I used action="#{mainBean.register})" method that returns "sign" string and none of these worked. There is one more file (not specified in faces-config.xml file, because did not work either - but going from login.xhtml by button works fine. I tried to manage navigation from login_failed.xhtml first, then I will apply the same rool for registration to come back to login page when customer registers his nick name). register.xhtml: Basicaly mainBean.register now calls the database and returns string, but obviously it doesn't navigate to any view (but gives an entry to database). I believe it is simple fix for most of the experienced web developers and any help will be greately appreciated. I use eclipse, tomcat 6 and Widows Vista if that helps :) Thank you in advance. Kindest regards.

    Read the article

  • Migration Core Data error code 134130

    - by magichero
    I want to do migration with 2 core database. I have read apple developer document. For the first database, I add some attributes (string, integer and date properties) to new version database. And follow all steps, I have done migration successfully with the first once. But the second database, I also add attributes (string, integer, date, transformable and binary-data properties) to new version database. And follow all steps (like the first database) but system return an error (134130). Here is the code: if (persistentStoreCoordinator_) { PMReleaseSafely(persistentStoreCoordinator_); } // Notify NSNotificationCenter *nc = [NSNotificationCenter defaultCenter]; [nc postNotificationName:GCalWillMigrationNotification object:self]; // NSString *sourceStoreType = NSSQLiteStoreType; NSString *dataStorePath = [PMUtility dataStorePathForName:GCalDBWarehousePersistentStoreName]; NSURL *storeURL = [NSURL fileURLWithPath:dataStorePath]; BOOL storeExists = [[NSFileManager defaultManager] fileExistsAtPath:dataStorePath]; // NSError *error = nil; NSDictionary *options = [NSDictionary dictionaryWithObjectsAndKeys: [NSNumber numberWithBool:YES], NSMigratePersistentStoresAutomaticallyOption, [NSNumber numberWithBool:YES], NSInferMappingModelAutomaticallyOption, nil]; persistentStoreCoordinator_ = [[NSPersistentStoreCoordinator alloc] initWithManagedObjectModel:self.managedObjectModel]; [persistentStoreCoordinator_ addPersistentStoreWithType:sourceStoreType configuration:nil URL:storeURL options:options error:&error]; if (error != nil) { abort(); } error is not nil and below is log: Error Domain=NSCocoaErrorDomain Code=134130 "The operation couldn\u2019t be completed. (Cocoa error 134130.)" UserInfo=0x856f790 {URL=file://localhost/Users/greensun/Library/Application%20Support/iPhone%20Simulator/5.0/Applications/D10712DE-D9FE-411A-8182-C4F58C60EC6D/Library/Application%20Support/Promise%20Mail/GCalDBWarehouse.sqlite, metadata={type = immutable dict, count = 7, entries = 2 : {contents = "NSStoreModelVersionIdentifiers"} = {type = immutable, count = 1, values = ( 0 : {contents = ""} )} 4 : {contents = "NSPersistenceFrameworkVersion"} = {value = +386, type = kCFNumberSInt64Type} 6 : {contents = "NSStoreModelVersionHashes"} = {type = immutable dict, count = 2, entries = 0 : {contents = "SyncEvent"} = {length = 32, capacity = 32, bytes = 0xfdae355f55c13fbd0344415fea26c8bb ... 4c1721aadd4122aa} 1 : {contents = "ImportEvent"} = {length = 32, capacity = 32, bytes = 0x7676888f0d7eaff4d1f844343028ce02 ... 040af6cbe8c5fd01} } 7 : {contents = "NSStoreUUID"} = {contents = "51678BAC-CCFB-4D00-AF5C-8FA1BEDA6440"} 8 : {contents = "NSStoreType"} = {contents = "SQLite"} 9 : {contents = "_NSAutoVacuumLevel"} = {contents = "2"} 10 : {contents = "NSStoreModelVersionHashesVersion"} = {value = +3, type = kCFNumberSInt32Type} }, reason=Can't find model for source store} I try a lot of solutions but it does not work. I just add more attributes to 2 new version database, and succeed in migrating once. Thanks for reading and your help.

    Read the article

  • OSX/Darwin unresolved symbols when linking functions from <math.h>

    - by tbone
    I'm in the process of porting a large'ish (~1M LOC) project from a Window/Visual Studio environment to other platforms, the first of which happens to be Mac OS X. Originally the project was configured as Visual Studio solutions and projects, but now I'm using (the excellent) Premake (http://industriousone.com/premake) to generate project files for multiple platforms (VS, XCode, GMake). I configured, ported and built the first few projects without any significant problems, but having ported the math lib, I ran into this weird linking error that I haven't been able to resolve: Any functions used from math.h will fail to link (causing unresolved symbols). For reference, I'm using Premake v4.2.1 to generate projects for XCode v3.2.1, which is building using gcc v4.2 for the x86_64 architecture. (All this on 64-bit Snow Leopard) I've tried to persuade gcc to link and build everything against a 'known' SDK by adding -isysroot /Developer/SDKs/MacOSX10.6.sdk -mmacosx-version-min=10.6 to the build command line. Now under normal circumstances, adding -lm should take care of this, however in Darwin, those math libs are included in libSystem, which, as far as I can tell, gets implicitly linked by gcc/ld. I've tried creating a dummy project from within XCode which just runs: float f = log2(2.0)+log2f(3.f)+log1p(1.1)+log1pf(1.2f)+sin(8.0); std::cout << f << std::endl; and as expected, this builds just fine. However, if I put the same thing in the code inside the Premake generated project, all those math functions end up unresolved. Now comparing the linking command from the 'native' XCode project with my generated XCode project, they seem pretty identical (except that my generated project links other libs as well). 'Native' project: /Developer/usr/bin/g++-4.2 -arch x86_64 -dynamiclib -isysroot /Developer/SDKs/MacOSX10.6.sdk -Lsomepath -Fsomepath -filelist somefile -install_name somename -mmacosx-version-min=10.6 -single_module -compatibility_version 1 -current_version 1 -o somename Generated project: /Developer/usr/bin/g++-4.2 -arch x86_64 -dynamiclib -Lsomepath -Fsomepath -filelist somefile -install_name somename -isysroot /Developer/SDKs/MacOSX10.6.sdk -mmacosx-version-min=10.6 somelib.a somelib2.a somelib.dylib somelib2.dylib -single_module -compatibility_version 1 -current_version 1 -o somename Any help or hints about how to proceed would be most appreciated. Are there any gcc flags or other tools that can help me resolve this?

    Read the article

  • Why does Visual Studio 2010 throw this error with Boost 1.42.0?

    - by ra170
    I'm trying to recompile application, that compiles fine with warning level 4 in visual studio 2005 and visual studio 2008. Since the errors (look below) are coming from std:tr1, I'm thinking there's some conflict, but not sure how to fix. My first thought was to remove all references to boost, such as but then I get an error that it can't find format method. So here's one of the errors: (not sure what it means) Any ideas, suggestions, solutions? Thanks! > c:\program files (x86)\microsoft > visual studio > 10.0\vc\include\type_traits(197): error C2752: > 'std::tr1::_Remove_reference<_Ty>' : > more than one partial specialization > matches the template argument list 1> > with 1> [ 1> > _Ty=bool (__cdecl &)(const BlahBlah &) 1> ] 1> c:\program > files (x86)\microsoft visual studio > 10.0\vc\include\xtr1common(356): could be > 'std::tr1::_Remove_reference<_Ty&&>' > 1> c:\program files > (x86)\microsoft visual studio > 10.0\vc\include\xtr1common(350): or 'std::tr1::_Remove_reference<_Ty&>' 1> > c:\program files (x86)\microsoft > visual studio > 10.0\vc\include\type_traits(962) : see reference to class template > instantiation > 'std::tr1::remove_reference<_Ty>' > being compiled 1> with

    Read the article

  • Autoloading Development or Production configs (best practices)

    - by Xeoncross
    When programming sites you usually have one set of config files for the development environment and another set for the production server (or one file with both settings). I am assuming all projects should be handled by version control like git or svn. Manual file transfers (like FTP) is wrong on so many levels. How you enable/disable the correct settings (so that your system knows which ones to use) is a problem for me. Each system I work on just kind of jimmy-rigs a solution. Below are the 3 methods I know of and I am hoping that someone can submit a more elegant solutions. 1) File Based The system loads a folder structure based on the URL requested. /site.com /site.fakeTLD /lib index.php For example, if the url is http://site.com then the system loads the production config files located in the site.com folder. However, if I'm working on the site locally I visit http://site.fakeTLD to work on the local copy of the site. To setup this I edit my hosts file and add site.fakeTLD to point to my own computer (127.0.0.1/localhost) and then create a vhost in apache. So now I can work on the codebase locally and then push to the server without any trouble. The problem is that this is susceptible to a "host" injection attack. So someone loading site.com could set the host to site.fakeTLD and then the system would load my development config files instead of production. 2) Config Based The config files contain on section for development - and one for production. The problem is that each time you go to push your changes to the repo you have to edit the file to specify which set of config options should be used. $use = 'production'; //'development'; This leaves the repo open to human error should one of the developers forget to enable the right setting. 3) File System Check Based All the development machines have an extra empty file called "development.txt" or something. Each time the system loads it checks for this file - if found then it knows it is in development mode - if missing then it knows it is in production mode. Since the file is NEVER ADDED to the repo then it will never be pushed (and checked out) on the production machine. However, this just doesn't feel right and causes a slight slow down since all filesystem checks are slow. Is there anyway that the server can auto-detect wither to use the development or production configs?

    Read the article

  • Using QT to build a WYSIWYG Editor for a Custom Markup Language

    - by Aaron
    I'm new to QT, and am trying to figure out the best means of creating a WYSIWYG editor widget for a custom markup language that displays simple text, images, and links. I need to be able to propagate changes from the WYSIWYG editor to the custom markup representation. As a concrete example of the problem domain, imagine that the custom markup might have a "player" tag which contains a player name and a team name. The markup could look like this: Last week, <player id="1234"><name>Aaron Rodgers</name><team>Packers</team></player> threw a pass. This text would display in the editor as: Last week, Aaron Rodgers of the Packers threw a pass. The player name and the team name would be editable directly within the editor in standard WYSIWYG fashion, so that my users do not have to learn any markup. Also, when the player name is moused-over, a details pop-up will appear about that player, and similarly for the team. With that long introduction, I'm trying to figure out where to start with QT. It seems that the most logical option would be the Rich Text API using a QTextDocument. This approach seems less than ideal given the limitations of a QTextDocument: I can't figure out how to capture navigation events from clicking on links. Following links on click seems to only be enabled when the QTextEdit is readonly. Custom objects that implement QTextObjectInterface are ignored in copy-and-paste operations Any HTML-based markup that is passed to it as Rich Text is retranslated into a series of span tags and lots of other junk, making it extremely difficult to propagate changes from the editor back to the original custom markup. A second option appears to be QWebKit, which allows for live editing of HTML5 markup, so I could specify a two-way translation between the custom markup and HTML5. I'm not clear on how one would propagate changes from the editor back to the original markup in real-time without re-translating the entire document on every text change. The QWebKit solutions looks like awfully bulky to me (Learning WebKit along with QT) to what should be a relatively simple problem. I have also considered implementing the WYSIWYG with a custom class using native QT containers, labels, images, and other widgets manually. This seems like the most flexible approach, and the one most likely not to run into unresolvable problems. However, I'm pretty sure that implementing all the details of a normal text editor (selecting text, font changes, cut-and-paste support, undo/redo, dragging of objects, cursor placement, etc.) will be incredibly time consuming. So, finally, my question: are there any QT gurus out there with some advice on where to start with this sort of project? BTW, I am using QT because the application is a desktop application that needs platform independence.

    Read the article

  • Dropdownlist and Datareader

    - by salvationishere
    After trying many solutions listed on the internet I am very confused now. I have a C#/SQL web application for which I am simply trying to bind an ExecuteReader command to a Dropdownlist so the user can select a value. This is a VS2008 project on an XP OS. How it works is after the user selects a table, I use this selection as an input parameter to a method from my Datamatch.aspx.cs file. Then this Datamatch.aspx.cs file calls a method from my ADONET.cs class file. Finally this method executes a SQL procedure to return the list of columns from that table. (These are all tables in Adventureworks DB). I know that this method returns successfully the list of columns if I execute this SP in SSMS. However, I'm not sure how to tell if it works in VS or not. This should be simple. How can I do this? Here is some of my code. The T-sQL stored proc: CREATE PROCEDURE [dbo].[getColumnNames] @TableName VarChar(50) AS BEGIN SET NOCOUNT ON; SELECT col.name 'COLUMN_NAME' FROM sysobjects obj INNER JOIN syscolumns col ON obj.id = col.id WHERE obj.name = @TableName END It gives me desired output when I execute following from SSMS: exec getColumnNames 'AddressType' And the code from Datamatch.aspx.cs file currently is: // Add DropDownList Control to Placeholder private void CreateDropDownLists() { SqlDataReader dr2 = ADONET_methods.DisplayTableColumns(targettable); int NumControls = targettable.Length; DropDownList ddl = new DropDownList(); } Where ADONET_methods.DisplayTableColumns(targettable) is: public static SqlDataReader DisplayTableColumns(string tt) { SqlDataReader dr = null; string TableName = tt; string connString = "Server=(local);Database=AdventureWorks;Integrated Security = SSPI"; string errorMsg; SqlConnection conn2 = new SqlConnection(connString); SqlCommand cmd = new SqlCommand("getColumnNames"); //conn2.CreateCommand(); try { cmd.CommandType = CommandType.StoredProcedure; cmd.Connection = conn2; SqlParameter parm = new SqlParameter("@TableName", SqlDbType.VarChar); parm.Value = "Person." + TableName.Trim(); parm.Direction = ParameterDirection.Input; cmd.Parameters.Add(parm); conn2.Open(); dr = cmd.ExecuteReader(); } catch (Exception ex) { errorMsg = ex.Message; } return dr; }

    Read the article

  • Problems related to showing MessageBox from non-GUI threads

    - by Hans Løken
    I'm working on a heavily data-bound Win.Forms application where I've found some strange behavior. The app has separate I/O threads receiving updates through asynchronous web-requests which it then sends to the main/GUI thread for processing and updating of application-wide data-stores (which in turn may be data-bound to various GUI-elements, etc.). The server at the other end of the web-requests requires periodic requests or the session times out. I've gone through several attempted solutions of dealing with thread-issues etc. and I've observed the following behavior: If I use Control.Invoke for sending updates from I/O-thread(s) to main-thread and this update causes a MessageBox to be shown the main form's message pump stops until the user clicks the ok-button. This also blocks the I/O-thread from continuing eventually leading to timeouts on the server. If I use Control.BeginInvoke for sending updates from I/O-thread(s) to main-thread the main form's message pump does not stop, but if the processing of an update leads to a messagebox being shown, the processing of the rest of that update is halted until the user clicks ok. Since the I/O-threads keep running and the message pump keeps processing messages several BeginInvoke's for updates may be called before the one with the message box is finished. This leads to out-of-sequence updates which is unacceptable. I/O-threads add updates to a blocking queue (very similar to http://stackoverflow.com/questions/530211/creating-a-blocking-queuet-in-net/530228#530228). GUI-thread uses a Forms.Timer that periodically applies all updates in the blocking queue. This solution solves both the problem of blocking I/O threads and sequentiality of updates i.e. next update will be never be started until previous is finished. However, there is a small performance cost as well as introducing a latency in showing updates that is unacceptable in the long run. I would like update-processing in the main-thread to be event-driven rather than polling. So to my question. How should I do this to: avoid blocking the I/O-threads guarantee that updates are finished in-sequence keep the main message pump running while showing a message box as a result of an update.

    Read the article

  • Need help manipulating WAV (RIFF) Files at a byte level

    - by Eric
    I'm writing an an application in C# that will record audio files (*.wav) and automatically tag and name them. Wave files are RIFF files (like AVI) which can contain meta data chunks in addition to the waveform data chunks. So now I'm trying to figure out how to read and write the RIFF meta data to and from recorded wave files. I'm using NAudio for recording the files, and asked on their forums as well on SO for way to read and write RIFF tags. While I received a number of good answers, none of the solutions allowed for reading and writing RIFF chunks as easily as I would like. But more importantly I have very little experience dealing with files at a byte level, and think this could be a good opportunity to learn. So now I want to try writing my own class(es) that can read in a RIFF file and allow meta data to be read, and written from the file. I've used streams in C#, but always with the entire stream at once. So now I'm little lost that I have to consider a file byte by byte. Specifically how would I go about removing or inserting bytes to and from the middle of a file? I've tried reading a file through a FileStream into a byte array (byte[]) as shown in the code below. System.IO.FileStream waveFileStream = System.IO.File.OpenRead(@"C:\sound.wav"); byte[] waveBytes = new byte[waveFileStream.Length]; waveFileStream.Read(waveBytes, 0, waveBytes.Length); And I could see through the Visual Studio debugger that the first four byte are the RIFF header of the file. But arrays are a pain to deal with when performing actions that change their size like inserting or removing values. So I was thinking I could then to the byte[] into a List like this. List<byte> list = waveBytes.ToList<byte>(); Which would make any manipulation of the file byte by byte a whole lot easier, but I'm worried I might be missing something like a class in the System.IO name-space that would make all this even easier. Am I on the right track, or is there a better way to do this? I should also mention that I'm not hugely concerned with performance, and would prefer not to deal with pointers or unsafe code blocks like this guy. If it helps at all here is a good article on the RIFF/WAV file format.

    Read the article

< Previous Page | 433 434 435 436 437 438 439 440 441 442 443 444  | Next Page >