Search Results

Search found 12281 results on 492 pages for 'ip blocking'.

Page 438/492 | < Previous Page | 434 435 436 437 438 439 440 441 442 443 444 445  | Next Page >

• Routing table on Linux not respected

  - by MRHaarmann

  I have a very specific problem, building a Linux VPN endpoint (with external VPN Gateway), which should route certain networks over the tunnel, others via default gateway. The Linux VPN should do a NAT on the outgoing connections for the VPN peers. Setup is as following: Internet gateway LAN 192.168.25.1/24 VPN Gateway LAN 10.45.99.2/24 (VPN tunnel 10.45.99.1 to net 87.115.17.40/29, separate connection to Internet) Linux VPN Router eth0 192.168.25.71/24 eth0:503 10.45.99.1/24 Default 192.168.25.1 route to 87.115.17.40/29 via 10.45.99.2 (send_redirects disabled, ip_forward enabled) Linux clients (multiple): eth0 192.168.25.x/24 Default 192.168.25.1 route to 87.115.17.40/29 via 192.168.25.71 Ping to the machines via tunnel from the VPN Router is working. Now I want to establish a routing from my clients over the VPN gateway and the client packet gets routed to 192.168.25.1 ! traceroute output shows the packets get routed to 192.168.25.71, but then to 192.168.25.1. So the route is not respected in forward ! IPTables and Routing: ip route show 87.115.17.40/29 via 10.45.99.2 dev eth0 10.45.99.0/24 dev eth0 proto kernel scope link src 10.45.99.1 192.168.25.0/24 dev eth0 proto kernel scope link src 192.168.25.71 default via 192.168.25.1 dev eth0 iptables -A INPUT -i eth0:503 -j REJECT iptables -t nat -A POSTROUTING -o eth0:503 -j MASQUERADE iptables -A FORWARD -i eth0:503 -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -s 192.168.25.0/24 -o eth0:503 -j ACCEPT So what is wrong with my setup ? The route is chosen correctly from localhost, but all the clients get forwarded to the Internet GW. thanks for helping, Marcus

  Read the article

• Win Svr 2003 DHCP Bad Addresses

  - by VinceM

  After looking at other posts I still can figure this out. I'll start at the beginning... I inherited this network and I'm not the most knowledgeable about networking... We have a AD DHCP Server that is also our DNS server, We were having some VPN issues (on the same server) and my boss decided to disable routing and remote access, which cleared the settings. We couldn't get it set back up correctly so we rolled back to a backup drive they created a number of months ago. Since rolling back I've had Bad_Address listings in DHCP and there is a number of duplicate records in the DNS Forward Lookup Zones. We have less than 50 devices on the network but I have over 90 Bad Addresses showing. This server is currently running but we get IP address conflicts all the time on pretty much all the computers. I have had people do release and renew but it didn't help... I have also deleted and re-added the scope to no avail either. Any help or ideas would be greatly appreciated and I apologize if I missed another post that has information to help. Thanks, Vince

  Read the article

• High latency due to non-presence of a transit provider in my country

  - by nixnotwin

  My ISP, a state owned incumbent, buys bandwidth from different transit providers. Whenever it buys transits it announces only a specific prefix (in most cases a hitherto unused) through the new transit AS. For e.g. if it runs out of bandwidth, it buys bandwidth from a new transit and announces a new prefix through it, while the same prefix is not announced (or announced with lowest metrics, so that the routes are very rarely used) via the old transits which continue to provide bandwidth to it. I am a business customer, so I have a fiber based link to the ISP and a tiny subnet is given to me. The subnet which is provide to me is part of a prefix which is announced by the AS of a transit who, it seems, do not have a presence in my country. So when I do a trace the packets, when they leave my ISP's AS, they take about 275ms to reach the transit providers core router, which is located in USA (half the world away). Also for upstream traffic my ISP uses a transit provider (tier 1) who has a presence in my country. But the return path is always through the transit which is in USA. So, average latency is 400ms. All the users of other ISPs in my country discover my subnet via USA. Even the traffic from neighboring countries, from Europe (which is much nearer) follows the path via USA. Sites using CDNs also resolve to ips in USA. I have informed the ISP NOC about the issue and I have asked them to provide an ip subnet belonging to a prefix announced by a local transit (preferably a tier 1 transit provider) and I am waiting for a reply. My question: Is it a serious issue that I must follow up to get it resolved? When I compared the latency on other providers in my country, it is, in most cases, less than half of my ISPs latency. Why my ISP doesn't announce all its prefixes to all of its transit providers, so that the packets can take efficient and nearest routes to reach prefixes that originate within its network?

  Read the article

• DNS to \\Server\ wrong - \\Server.company.local\ works fine

  - by JimmyClif

  I had a little network glitch and since then one of my servers shows up wrong at some workstations when typing in \\server\. Example: On workstationA I go to Explorer and and type \\server\ and it brings me to our copier at 192.168.2.101. \\server.company.local\ gets me to the right place at 192.168.2.252. Ping with server pings 192.168.2.252 - same correct result with ping server.company.com nslookup also shows correct result with both. reverse lookup by ip is correct also. I flush the DNS on the workstation and the error still occurs. reboot same result. At that point I give up and start remapping the shares to \\server.company.local\share just to get the user back working... DNS Server has correct entries for that server. Can access the server via \\server\ on dns server, all looks fine. Eventually the workstation figures it out by itself and \\server\ works again but my life wouldn't be as stressful if I had a clue what happened or how to fix it myself. Thanks for your time looking and answering.

  Read the article

• Router startup problem

  - by gfmoz

  I have problems with my Tilgin Vood Router. As I try to start my router by turning the power on (captain obvious), it generally doesn't work the first 3-4 times. This is getting very annoying. Five minutes after turning the power on the router's signal LEDs don't blink in the way they should do in a connected state. I can connect to my routers web configuration interface through my PC connected to it via LAN though I can't access the internet. It usually takes the router five minutes to get to the point where it should be connected to the internet but as it doesn't work the first times. So I turn on my router 3-5 times, let him work 5 minutes and then suddenly, after turning the pow*emphasized text*er off and on again it all works. The problem is regarding startup only, when I get it to work everything runs as smooth as a 1980-s text-based C++ game on a 3ghz machine. I also have to restart my PC too in order for everything to work. - How can I solve this problem? - Just leave the router turned on all time? I prefer a daily IP switch, though. - May the problem have something to do with my PC? There is another one connected to the router too and it doesn't work there either.

  Read the article

• Host name change breaking http? Fedora

  - by Dave

  OK so I have been messing around on my development server. It has been a while since I have had my head in linux and I suspect I have broken something. I have SSH running and that is working fine. I also have HTTP and I had FTP running also. Earlier today I decided I wanted to rename the machine so I updated the /etc/hosts file and /etc/sysconfig/network. I also changed the server name in the httpd.conf. I rebooted the machine and reconnected to SSH fine. Later I was messing around with the FTP service (trying to tighten up the user security) and when i tried to connect remotely to FTP no joy, it said cannot connect. I thought that was weird but had planned to remove ftp as we will be using github so removed ftp and moved on. Then I tried to connect to the website but major fail. even connecting to the IP address is failing. I used lynx to connect to the localhost and there was my site so something going on at server level. I thought maybe something up with iptables but I have not changed them but tried adding http but still no joy. I have a - Fedora release 17 (Beefy Miracle) NAME=Fedora VERSION="17 (Beefy Miracle)" ID=fedora VERSION_ID=17 PRETTY_NAME="Fedora 17 (Beefy Miracle)" ANSI_COLOR="0;34" CPE_NAME="cpe:/o:fedoraproject:fedora:17" Fedora release 17 (Beefy Miracle) Fedora release 17 (Beefy Miracle) Linux version 3.3.4-5.fc17.x86_64 ([email protected]) (gcc version 4.7.0 20120504 (Red Hat 4.7.0-4) (GCC) ) #1 SMP Mon May 7 17:29:34 UTC 2012 This is my iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT icmp -- anywhere anywhere ACCEPT all -- anywhere anywhere ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:ssh REJECT all -- anywhere anywhere reject-with icmp-host-prohibited Chain FORWARD (policy ACCEPT) target prot opt source destination REJECT all -- anywhere anywhere reject-with icmp-host-prohibited Chain OUTPUT (policy ACCEPT) target prot opt source destination Like I say I can use SSH no issue but http although running is a no go from a remote computer. Any ideas?

  Read the article

• Unable to login through varnish cache

  - by ArunS

  I am setting up Active Collab Site in my new server. The setup is like below Internet --- varnish ---- apache But i am not able to login to the site through varnish cache.. But i can login to site through apache. Here is my VCL file backend default { .host = "localhost"; .port = "8080"; } acl purge { "localhost"; } sub vcl_recv { if (req.request == "PURGE") { if (!client.ip ~ purge) { error 405 "Not allowed."; } return(lookup); } if (req.url ~ "^/$") { unset req.http.cookie; } } sub vcl_hit { if (req.request == "PURGE") { set obj.ttl = 0s; error 200 "Purged."; } } sub vcl_miss { if (req.request == "PURGE") { error 404 "Not in cache."; } if (!(req.url ~ "wp-(login|admin)")) { unset req.http.cookie; } if (req.url ~ "^/[^?]+.(jpeg|jpg|png|gif|ico|js|css|txt|gz|zip|lzma|bz2|tgz|tbz|html|htm)(\?.|)$") { unset req.http.cookie; set req.url = regsub(req.url, "\?.$", ""); } if (req.url ~ "^/$") { unset req.http.cookie; } } sub vcl_fetch { if (req.url ~ "^/$") { unset beresp.http.set-cookie; } if (!(req.url ~ "wp-(login|admin)")) { unset beresp.http.set-cookie; }} When i try to login through varnish i was redirect back to login page. If i enter wrong password, then it will ask for enter correct password.

  Read the article

• Exchange 2010 issuing NDRs to Hotmail/Live & few other domains on receipt of message

  - by John Patrick Dandison

  I'm working through a beast of an issue at the moment. Exchange 2010 single server on prem Hybrid deployment to Office 365 ESMTP filtering turned off on ASA Certain domains (most consistently, Hotmail/Live) cannot send us mail. At one point, we couldn't send out either, but I created a new Send Connector that forces HELO instead of EHLO. I turned on SMTP logging, an example of the failed inbound message connection is below. I've read that it could be that reverse DNS is the problem, i.e., the exchange banner smtp address needs to reverse-DNS back to the same IP. Since it's the default exchange connector, its banner is the server's name, but the DNS name of the MX record is different. I'm waiting for the PTR records to update to reflect the internal name as well. Is that the right direction? Is this all DNS or something different? SMTP Session Log (single failed session for illustration): SMTPSubmit SMTPAcceptAnySender SMTPAcceptAuthoritativeDomainSender AcceptRoutingHeaders 220 ExchangeServerName.internalSubDomain.example.com Microsoft ESMTP MAIL Service ready at Mon, 15 Oct 2012 09:57:24 -0400 EHLO col0-omc3-s4.col0.hotmail.com 250-ExchangeServerName.internalSubDomain.example.com Hello [65.55.34.142] 250-SIZE 250-PIPELINING 250-DSN 250-ENHANCEDSTATUSCODES 250-STARTTLS 250-X-ANONYMOUSTLS 250-AUTH NTLM LOGIN 250-X-EXPS GSSAPI NTLM 250-8BITMIME 250-BINARYMIME 250-CHUNKING 250-XEXCH50 250-XRDST 250 XSHADOW MAIL FROM:<[email protected]> 08CF5268DABBD9AA;2012-10-15T13:57:24.564Z;1 250 2.1.0 Sender OK RCPT TO:<[email protected]> 250 2.1.5 Recipient OK XXXX 1282 LAST Tarpit for '0.00:00:05' 500 5.3.3 Unrecognized command XXXXXXXXX from COL002-W38 ([65.55.34.135]) by col0-omc3-s4.col0.hotmail.com with Microsoft SMTPSVC(6.0.3790.4675); Tarpit for '0.00:00:05' 500 5.3.3 Unrecognized command " XXXX 15 Oct 2012 06:57:24 -0700" Tarpit for '0.00:00:05' 500 5.3.3 Unrecognized command XXXXXXXXXXX <[email protected]> Tarpit for '0.00:00:05'

  Read the article

• CUPS printer on Vritual Machine can be access via CUPS admin, but not by XP?

  - by SJaguar13

  I have a Zebra label printer connected to a Linux Mint virtual machine. It was set up with CUPS and a Windows XP computer can then print to it via http://192.168.1.76:632/printers/labelprinter. That was all fine and dandy I then hooked up a Fargo Pro L PVC card printer to a Windows XP virtual machine. I had to disconnect the label printer as the server that hosted both virtual machines only has 1 parallel port. Now I plugged in the Zebra again, and it cannot print from the Windows XP computer anymore. If I go to the CUPS admin panel on the Windows XP computer, I can see it, everything looks fine, and I can send it a test page to print which works. If I try to print from Windows, I get an error that the printer is not found/cannot connect to the server. The only other thing that changed was the firewall on the router to allow remote desktop to another computer from outside the network, but all the firewall stuff was for external use. Nothing affected the IP address of the internal network. The Linux Mint VM also had a PDF pritner that was shared with CUPS. That printer is also down. I tried setting up a new CUPS installation on another VM, and when I go to share it with XP, I get the same error. I don't know what to try. It has access, it can get to the admin from that computer, it seems to be up and ready, but when Windows tries to connect, the printer isn't found even though 4 days ago everything was fine. Any ideas?

  Read the article

• Postgres pgpass windows - not working

  - by Scott

  DB: Postgres 9.0 Client: Windows 7 Server Windows 2008, 64bit I'm trying to connect remotely to a postgres instance for purposes of performing a pg_dump to my local machine. Everything works from my client machine, except that I need to provide a password at the password prompt, and I'd ultimately like to batch this with a script. I've followed the instructions here: http://www.postgresql.org/docs/current/static/libpq-pgpass.html but it's not working. To recap, I've created a file on the client (and tried the server as well): C:/Users/postgres/AppData/postgresql/pgpass.conf, where postgresql is the db user. The file has one line with the following data: *:5432:*postgres:[mypassword] (also tried explicit ip/dbname values, all asterisks, and every combination in between. (I've also tried replacing each '*' with [localhost|myip] and [mydatabasename] respectively. From my client machine, I connect using: pg_dump -h [myip] -U postgres -w [mydbname] [mylocaldumpfile] I'm presuming that I need to provide the '-w' switch in order to ignore password prompt, at which point it should look in the AppData directory on the server. It just comes back with "connection to database failed: fe_sendauth: no password supplied. Any insights are appreciated. As a hack workaround, if there was a way I could tell the windows batch file on my client machine to inject the password at the postgres prompt, that would work as well. Thanks.

  Read the article

• My DNS works! But, what is the simplest way to add something to it?

  - by Alex

  This is my current DNS example.com.db zone file. I followed a tutorial. It works, because when I point to this DNS from another server via resolve.conf, it will actually forward me to the right IP when I do "ping example.com". ; ; BIND data file for example.com ; $TTL 604800 @ IN SOA example.com. info.example.com. ( 2007011501 ; Serial 7200 ; Refresh 120 ; Retry 2419200 ; Expire 604800) ; Default TTL ; @ IN NS ns1.example.com. @ IN NS ns2.example.com. example.com. IN MX 10 mail.example.com. example.com. IN A 192.168.254.1 www IN CNAME example.com. mail IN A 192.168.254.1 ftp IN CNAME example.com. example.com. IN TXT "v=spf1 ip4:192.168.254.1 a mx ~all" mail IN TXT "v=spf1 a -all" Right now, ping example.com....goes to 192.168.254.1. That's great!!! it works! My question is--how can I add something do this file so that when my other servers: ping dbserver1....goes to 44.245.66.222 ping cacheserver1 ....goes to 38.221.44.555 I want to use it like a universal hosts file for my machines.

  Read the article

• Why does my Intel Tolapai network chip not transmit packets?

  - by Hanno Fietz

  I'm trying to deploy an embedded system (NISE 110 by Nexcom) based on the Intel EP80579 (Tolapai) chip. Tolapai apparently integrates controllers for Ethernet etc. on a single chip (Intel homepage). The machine can't get a network connection. Diagnosis as far as I could manage: Drivers drivers from Intel compiled and installed without problems (version 1.0.3-144). Kernel version and Linux distribution (CentOS 5.2, 2.6.18) match the driver's installation instructions. drivers are loaded and show up in lsmod (module names are gcu and iegbe) interfaces eth0 and eth1 show up in ifconfig ifconfig I can bring up the interfaces with fixed IP pinging the interface locally works ifconfig shows flag UP but not RUNNING Link ethtool shows "Link detected: no", "Speed: unknown (65536)" and "Duplex: unknown (255)" Link LED is on on the other side of the cable, ethtool shows "Link detected: yes" and reports a speed of 1000 Mbps, which has allegedly been auto-neogotiated with the problematic device. Network traffic analysis the device does not reply on ARP, ICMP echo or anything else (iptables is down) when trying to send ICMP or DHCP requests, they never reach the other end activity LED is off on the device, on at the other end. I tried the following without any effect: Different cables (2 straight, one crossed), I get the link LED lit up on each. Three different devices on the other end (one PC, one netbook, one router) Fixed ARP table entries on both sides Connecting both network ports of the machine with each other, won't ping through the cable, but will ping locally. Tried straight and crossed cables for that.

  Read the article

• DNS Zone file and virtual host question (repost because my question got moved and now I can't comment on the original for some reason)

  - by Jake

  Sorry this is a repost, the original question got moved to here form stack overflow and for some reason I can't comment or respond to answers on that one anymore. Hi all, I'm trying to set up a virtual host for redmine.SITENAME.com. I've edited the httpd.conf file and now I'm trying to edit my DNS settings. However, I'm not sure exactly what to do. Here's an snippet of what's already in the named.conf file (the file was made by someone else who is unreachable): zone "SITENAME.com" { type master; file "SITENAME.com"; allow-transfer { ip.address.here.00; common-allow-transfer; }; }; I figure if I want to get redmine.SITENAME.com working, I need to copy that entry and just replace SITENAME.com with redmine.SITENAME.com but will that work? I was under the impression I needed a .db file but I don't see any reference to one in the current named.conf file. I also don't see any .db files or files named SITENAME in named.conf's directory. Any ideas where these illusive pre-existing db files could be?

  Read the article

• Block SMTP session with sender domain which doesn't itself accept SMTP connection.

  - by bignose

  I'm administrating a mail service for a small business. Their mail host's internet connection is an ADSL service with a permanent IP address. Unfortunately, many misconfigured mail systems will happily deliver to this host, but, when the host attempts to send mail back (e.g. a bounce notice, or a normal response from someone), the declared sender's domain has an MX which refuses to receive connections from this host. That misconfiguration makes their system a one-way mail sender, which is a problem. How can I configure Postfix on this customer's mail host to refuse SMTP sessions that declare a sender domain which itself refuses SMTP from this host? That is, if the SMTP client declares a domain that we can't make SMTP connections back to, then there's not much point accepting the incoming connection in the first place. Note that I'm not, as some commenters have assumed, talking about checking whether the SMTP client will receive messages. The check I want is whether the declared sender's domain (regardless of who the current SMTP client is) will accept SMTP connections from here. In other words: when we get around to sending a message back, we'll need the sender's domain to accept SMTP connections; I want to do that check before accepting the incoming session. I'm imagining a late check (after the low-cost checks to winnow most of the rubbish connections) that keeps the client on the other end while it attempts an SMTP client connection back to the declared domain of the sender. If that connection is rejected, the incoming one is also rejected. I'm also open to other suggestions for how this problem might be addressed (short of not using this mail host at all, which isn't an option).

  Read the article

• virtualbox instances dedicated-server with custom dnsmasq

  - by ovanes

  I have dedicated server where I planned to run virtualbox virtual machines. Since the VMs are managed with vagrant/chef I may end up with many different ones. I thought it would be a great idea to deploy a dnsmasq on the server, which is going to dynamically assign the ip addresses to the VMs. Since each Vagrant/Chef recipe is configured to set the VM's host name I can find/reference the appropriate VM by the host name. Finally, the entire infrastructure is not directly accessible via internet, so the dedicated Server is the OpenVPN host. So the entire infrastructure may be seen as: +-------------------------------------+ | Dedicated Server | | | | +-------------+ +------------+ | +------------------+ | | DNSMasq | | OpenVPN |<==========>| Client | | +-------------+ +------------+ | | | | ^ ^ | +------------------+ | | | | | +--+ | | | | +-------+ | | | | VM1 | | | | +-------+ | | | ... | | | +-------+ | | +-| VM2 | | | +-------+ | +-------------------------------------+ Now some questions which I am struggling with: Are there any other suggestions to access private infrastructure, because I don't want to reinvent the wheel. On the Dedicated Server I don't see the vboxnet0 interface but VirtualBox is installed without GUI. Accessing of virtual boxes via ssh works fine. Did I miss smth? DNSMasq must serve the local VMs only, otherwise there is a chance that local DNSMasq start to serve other server's on the network, what I don't want. Because I don't see vboxnet0 I tend to use no-dhcp-interface=eth0 config option. Are there any thoughts on that despite, the fact that a second NW-card (which is not the case), might start serving DHCP-Requests? How should I config the VM's network interface that I am able to access it via OpenVPN and resolve the hostnames using the DNSMasq. I think it should be the host-only network card. Should I do bridging in the OpenVPN config or is it sufficient to use routing.

  Read the article

• how to block spam email using Microsoft Outlook 2011 (Mac)?

  - by tim8691

  I'm using Microsoft Outlook 2011 for Mac and I'm getting so much spam I'm not sure how to control it. In the past, I always applied "Block Sender" and "Mark as Junk" to any spam email messages I received. This doesn't seem to be enough nowadays. Then I've started using Tools Rules to create rules based on subject, but the same spammer keeps changing subject lines, so this isn't working. I've been tracking the IP addresses they also seem to be changing with each email. Is there any key information I can use in the email to apply a rule to successfully place these spam emails in the junk folder? I'm using a "Low" level of junk email protection. The next higher level, "high", says it may eliminate valid emails, so I prefer not to use this option. There's maybe one or two spammers sending me emails, but the volume is very high now. I'm getting a variation of the following facebook email spam: Hi, Here's some activity you have missed. No matter how far away you are from friends and family, we can help you stay connected. Other people have asked to be your friend. Accept this invitation to see your previous friend requests Some variations on the subject line they've used include: Account Info Change Account Sender Mail Pending ticket notification Pending ticket status Support Center Support med center Pending Notification Reminder: Pending Notification How do people address this? Can it be done within Outlook or is it better to get a third party commercial software to plug-in or otherwise manage it? If so, why would the third party be better than Outlook's internal tools (e.g. what does it look for in the incoming email that Outlook doesn't look at)?

  Read the article

• Files deleted. What could have happened?

  - by jjfine

  I'm having a weird issue today. I was writing and testing out some simple cgi scripts this morning when I realized that I couldn't run them from one of the other computers on the (windows) network. So I had my network admin come in and take a look at what was going on. A few minutes later a co-worker came in and told me that a bunch of files he was working with as well as a bunch of others (all *.c files) on the network drive got deleted. He also noticed some strange apache_dump_500.log.txt files in the same directories where the files got deleted. The apache_dump_500.log.txt files all look like this: REDIRECT_HTTP_ACCEPT=*/*, image/gif, image/x-xbitmap, image/jpeg REDIRECT_HTTP_USER_AGENT=Mozilla/1.1b2 (X11; I; HP-UX A.09.05 9000/712) REDIRECT_PATH=.:/bin:/usr/local/bin:/etc REDIRECT_QUERY_STRING= REDIRECT_REMOTE_ADDR=<my computer's local ip> REDIRECT_REMOTE_HOST= REDIRECT_SERVER_NAME=<my computer's domain url> REDIRECT_SERVER_PORT= REDIRECT_SERVER_SOFTWARE= REDIRECT_URL=/cgi-bin/trojan.py I looked and I don't have any trojan.py in my cgi-bin folder. And all my apache logs are clean. Windows event logger seems to not have any traces of what happened either. My httpd.conf: http://pastebin.com/Yny2Yh8v I think we've got some kind of virus that added this trojan.py file to my cgi-bin, ran the script, and deleted the script and any traces from the logs. Is this a thing that happens? Any ideas whatsoever would be much appreciated!

  Read the article

• Bad Mumble control channel performance in KVM guest

  - by aef

  I'm running a Mumble server (Murmur) on a Debian Wheezy Beta 4 KVM guest which runs on a Debian Wheezy Beta 4 KVM hypervisor. The guest machines are attached to a bridge device on the hypervisor system through Virtio network interfaces. The Hypervisor is attached to a 100Mbit/s uplink and does IP-routing between the guest machines and the remaining Internet. In this setup we're experiencing a clearly recognizable lag between double-clicking a channel in the client and the channel joining action happening. This happens with a lot of different clients between 1.2.3 and 1.2.4 on Linux and Windows systems. Voice quality and latency seems to be completely unaffected by this. Most of the times the client's information dialog states a 16ms latency for both the voice and control channel. The deviation for the control channels mostly is a lot higher than the one of the voice channels. In some situations the control channel is displayed with a 100ms ping and about 1000 deviation. It seems the TCP performance is a problem here. We had no problems on an earlier setup which was in principle quite like the new one. We used Debian Lenny based Xen hypervisor and a soft-virtualised guest machine instead and an earlier version of the Mumble 1.2.3 series. The current murmurd --version says: 1.2.3-349-g315b5f5-2.1

  Read the article

• IPC between multiple processes on multiple servers

  - by z8000

  Let's say you have 2 servers each with 8 CPU cores each. The servers each run 8 network services that each host an arbitrary number of long-lived TCP/IP client connections. Clients send messages to the services. The services do something based on the messages, and potentially notify N1 of the clients of state changes. Sure, it sounds like a botnet but it isn't. Consider how IRC works with c2s and s2s connections and s2s message relaying. The servers are in the same data center. The servers can communicate over a private VLAN @1GigE. Messages are < 1KB in size. How would you coordinate which services on which host should receive and relay messages to connected clients for state change messages? There's an infinite number of ways to solve this problem efficiently. AMQP (RabbitMQ, ZeroMQ, etc.) Spread Toolkit N^2 connections between allservices (bad) Heck, even run IRC! ... I'm looking for a solution that: perhaps exploits the fact that there's only a small closed cluster is easy to admin scales well is "dumb" (no weird edge cases) What are your experiences? What do you recommend? Thanks!

  Read the article

• Apache and Virtual Hosts Problem on OS X

  - by Charles Chadwick

  I recently formatted and installed my iMac. I am running 10.6.5. Prior to this format, I had the default Apache web server up and running with several virtual hosts, and everything ran beautifully. After formatting, I set everything back up again, and now Apache is acting funny. Here is a description of what I have going on. My default root directory for the Apache Web server is pointed to an external hard drive. In my httpd.conf, here is what I have: DocumentRoot "/Storage/Sites" Then a few lines beneath that: <Directory /> Options FollowSymLinks AllowOverride All Order deny,allow Allow from all </Directory> And then beneath that: <Directory "/Storage/Sites"> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny Allow from All </Directory> At the end of this file, I have commented out the user dir include conf file: Include /private/etc/apache2/extra/httpd-userdir.conf And uncommented the virtual hosts conf file: Include /private/etc/apache2/extra/httpd-vhosts.conf Moving on, I have the following entry in my vhosts file: <VirtualHost *:80> DocumentRoot "/Storage/Sites/mysite" ServerName mysite.dev </VirtualHost> I also have a host record in my /etc/hosts file that points mysite.dev to 127.0.0.1 (I also tried using my router IP, 192.168.1.2). The problem I am coming across is, despite having PHP files in /Storage/Sites/mysite, the server is still looking at /Storage/Sites. I know this because in the DocumentRoot contains a php file with phpinfo() (whereas the index.php file in mysite has different code). I have tried setting up other virtual hosts, but they are still doing the same thing. Also, "NameVirtualHost *:80" is in my vhosts file. I saw as a solution on another thread here. Doesn't seem to make a difference. Any ideas on this? Let me know if this is not enough information.

  Read the article

• VLAN Through Switch Doesn't Work

  - by vcsjones

  I have the following scenario: I have a Cisco Aironet 1040 access point. I have it configured with two SSIDs, each going to a different VLAN. So: SSID internal : VLAN 90 SSID guest : VLAN 70 On the router side, I have a Cisco RV220W (with the radios now turned off) and have setup VLANs with like VLAN IDs. VLAN 90 : 192.168.90.0/24 VLAN 70 : 192.168.70.0/24 As far as DHCP is concerned, each VLAN has a "DHCP Server" in the router's configuration: So with the access point connected directly to the router, everything works great. I connect to the internal network, and I get a 192.168.90.x address, and the guest network gets a 70.xxx address. Next I introduced a Cisco SG200-50 PoE switch between the router and the access point. The port is configured as a trunk port, so the VLAN tags should go right through the switch back to the router. However, when something is connected to the access point, nothing works. It isn't able to get an IP address, and manually assigning one doesn't seem to let any traffic route. Given that the access point works correctly when connected to the router directly, I believe the switch is misconfigured. What am I missing here? What can I use to better diagnose what the problem might be? It's small business equipment, so CLI access is not available. Below are screenshots of the switch's config. The access point is connected to GE2.

  Read the article

• Unable to access site over HTTPS using self signed certificate

  - by James

  I am developing a REST API which I want to secure with SSL/TLS. I have implemented a large part of the API which I have tested over HTTP, however, I am now at the stage where I want to switch it over to use HTTPS. At the moment the API is hosted on a Windows XP professional SP2 box running IIS 5.1 (development environment only) and I used the SelfSSL.exe tool from the IIS 6.0 Resource Kit Tools to generate a server certificate. I then configured my API to use this certificate which all appeared to work fine as I attempted to connect to my API using HTTP and I get a 403 response saying "... must be accessed over a secure channel...". However, the problem is when I attempt to access the same the API over HTTPS it just appears to hang! As this is a development environment at the moment I don't have a domain name (just a static IP address) and the API is running on port 81. Also (incase it matters) the API is the default site (I replaced it). Any ideas why I can't connect using HTTPS?

  Read the article

• nginx - proxy_pass is working - Apache isn't doing what it should...

  - by matthewsteiner

  So, I've got this in my nginx.conf: location ~* ^.+.(jpg|jpeg|gif|png|ico|css|zip|tgz|gz|rar|bz2|doc|xls|exe|pdf|ppt|txt|tar|mid|midi|wav|bmp|rtf|js)$ { root /var/www/vhosts/example.com/public/; access_log off; expires 30d; } location / { proxy_pass http://127.0.0.1:8080/; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } So anything that is a "static file" that exists will just be done with nginx. Otherwise, it should pass it off to Apache. Right now, static files are working correctly. However, if something is passed to apache and it's example.com or subdomain.example.com, apache just spits out the "Apache 2 Test Page" that you get if there's nothing there. Apache worked fine before, so I'm guessing it has to do with the way nginx is "asking". I'm not sure though. Any ideas?

  Read the article

• "Network Error - 53" while trying to mount NFS share in Windows Server 2008 client

  - by Mike B

  CentOS | Windows 2008 I've got a CentOS 5.5 server running nfsd. On the Windows side, I'm running Windows Server 2008 R2 Enterprise. I have the "Files Services" server role enabled and both Client for NFS and Server for NFS are on. I'm able to successfully connect/mount to the CentOS NFS share from other linux systems but am experiencing errors connecting to it from Windows. When I try to connect, I get the following: C:\Users\fooadmin>mount -o anon 10.10.10.10:/share/ z: Network Error - 53 Type 'NET HELPMSG 53' for more information. (IP and share name have been changed to protect the innocent :-) ) Additional information: I've verified low-level network connectivity between the Windows client and the NFS server with telnet (to the NFS on TCP/2049) so I know the port is open. I've further confirmed that inbound and outbound firewall ports are present and enabled. I came across a Microsoft tech note that suggested changing the "Provider Order" so "NFS Network" is above other items like Microsoft Windows Network. I changed this and restarted the NFS client - no luck. I've confirmed that the share folder on the NFS server is readable/writable by all (777) I've tried other variations of the mount command like: mount 10.10.10.10:/share/ z: and mount 10.10.10.10:/share z: and mount -o anon mtype=hard \\10.10.10.10:/share * No luck. As per the command output, I tried typing NET HELPMSG 53 but that doesn't tell me much. Just "The network path was not found". I'm lost on how to proceed with troubleshooting. Any ideas?

  Read the article

• How to determine the root cause of a system lockup on Ubuntu 8.04 LTS?

  - by jdt141

  I'm currently working a project that involves setting up a PC/104 stack and running Ubuntu 8.04 LTS. We need to use the PC/104 stack because its an embedded application - and we're required to use a DeviceNet peripheral card to communicate to other devices. (DeviceNet is just a protocol on top of CAN.) Anyway, the following hardware is on the stack: Kontron MOPSPM104 with a 1GHz Intel Celeron processor ConnectTech FlashDrive/104 4GB Industrial Temp (-40 to +85 C) Woodhead (Molex) PC104DVNIO DeviceNet card A run of the mill 104 power supply The Kontron Board offers two serial ports, one VGA out, and two USB ports. The DeviceNet card is an ISA card. Because of this (per the User's Guide for the Kontron Board), I have manually set the IRQs in the BIOS to be appropriately configured, and turned off ACPI in both the BIOS and passed the appropriate flag in GRUB. I've installed Ubuntu 8.04 desktop, 32 bit. The problem that I'm having is that, from time to time, the entire 104 stack locks up. This only seems to happen in two cases, both of which we're running GNOME. We have a custom application that uses the DeviceNet card, and the system will lock up, or (more frequently) when we're running Firefox and either surfing for some information or trying to test it - typically by streaming video from a IP-camera. The reason I ask this questions is I cannot determine the root cause of this lockup. The IRQs appear to correctly configured in the BIOS and as the Kernel sees them, and nothing is logged to dmesg. If you all could help me determine the root cause of this lockup, I would greatly appreciate it. Thanks.

  Read the article

< Previous Page | 434 435 436 437 438 439 440 441 442 443 444 445  | Next Page >