Search Results

Search found 27870 results on 1115 pages for 'standard output'.

Page 439/1115 | < Previous Page | 435 436 437 438 439 440 441 442 443 444 445 446  | Next Page >

• Unable to install 11.10 to new OCZ Agility 3 SSD

  - by Masi

  I know the discussion here where they are not getting the same error as I. I use Lenovo Thinkpad X60. The default partition table: sd1 ext4 53.91GB, sd2 extended 1.99GB and sd5 swap 1.99GB. I get Input/output error during read on /dev/sda when trying to install from LiveCD -mode and when trying to install directly. I get the error normally at the stage of choosing time zone or very last at choosing the keyboard layout. Then there is the box with buttons: back, ignore and continue. Neither of them put the process forward so I need to cancel it. How can you install Ubuntu to SDD disk?

  Read the article

• Speakers don't work in 12.10 but they work fine on windows7

  - by giri

  I have recently upgraded my Ubuntu 12.04 to 12.10 version and find issues with my speakers as well as microphone. When I boot the system they don't work, but(don't know why) when I restart once or twice they work fine. There is no problem with my laptop(dell xps) as they work well on windows7. I have my sound settings as follows Hardware --- Built-in Audio 1 Outpu/1 Input Analog Stereo Duplex Input(Internal Microphone) & Output(Speakers) -----Built-in audio Analog Stereo Any suggestions to fix the problem??

  Read the article

• Can I use GPL software in a commercial application

  - by Petah

  I have 3 questions about the GPL here: If I use GPL software in my application, but don't modify or distribute it, do I have to release my application under the GPL? What if I modify some software that my application uses. Then do I have to release my application under the GPL, or can I just supply the modified software under the GPLs terms. And what if I use GPL software, but don't modify it, can I distribute it with my application? My case in point is, I have a PHP framework which I use the GeSHi library to highlight some output. Because GeSHi is GPL, does my framework have to be GPL? Can I modify GeSHi for particular use cases of my application if I supply the modifications back to the GeSHi maintainers? Can I redistribute my framework with GeSHi?

  Read the article

• SQL Concatenate

  - by Bunch

  Concatenating output from a SELECT statement is a pretty basic thing to do in SQL. The main ways to perform this would be to use either the CONCAT() function, the || operator or the + operator. It really all depends on which version of SQL you are using. The following examples use T-SQL (MS SQL Server 2005) so it uses the + operator but other SQL versions have similar syntax. If you wanted to join two fields together for a full name: SELECT (lname + ', ' + fname) AS Name FROM tblCustomers To add some static text to a value: SELECT (lname + ' - SS') AS Name FROM tblPlayers WHERE PlayerPosition = 6 Or to select some text and an integer together: SELECT (lname + cast(playerNumber as varchar) AS Name FORM tblPlayers Technorati Tags: SQL

  Read the article

• Grep in a variable

  - by Ashfame

  How to do a grep in a variable? I have stored the wget output in a variable and I need to extract out some strings from it. Like the content of the variable is upgrade http://wordpress.org/download/ http://wordpress.org/wordpress-3.0.5.zip 3.0.5 en_US 4.3 4.1.2 I need to check if the string contains the word upgrade, so I can do a simple grep and then check the exit status of it by $? and proceed. But how can I get the value 3.0.5 which is actually the fourth word? And how to actually grep in a variable?

  Read the article

• Quantal analyzes the HD in any boot

  - by Lucio

  I have installed Ubuntu 12.10 formating the HDD. Any time that I turn on the PC and boot Ubuntu, it always analyzes my HDD in search for bad blocks. This is what happens: When I turn on the PC and load Ubuntu, before I can login my user, appears the following image. If I press C, the process ends and I can work, if I wait until the process can finish by itself also I can work. Also I had this problem, related to the HDD. My Hard Disk Driver is a Western Digital. Is there any problem on the system? Can I stop this procedure? Information that can help: tune2fs -l output

  Read the article

• How can a Cisco Aironet wireless card connect to a WPA encrypted network?

  - by Aibara Iduas

  I have a Thinkpad T40 running Ubuntu 10.10. I want to connect to wireless networks with WPA encryption; they appear in the network list, but are grayed out. The card does support WPA, since it works in Windows. In 10.10 the wireless works just fine with unprotected and WEP networks, but cannot connect to any WPA networks. The card is a Cisco Aironet Wireless 802.11b. I've been reading a lot of forum posts trying to find a solution, but either encounter threads where no solution was found or answers longer apply (most date from 2007, since this isn't the newest of computers). Here is the output of sudo lshw -c network: *-network:1 DISABLED description: Wireless Interface product: Cisco Aironet Wireless 802.11b vendor: AIRONET Wireless Communications physical id: 2 bus info: pci@000:02:02.0 logical name: eth1 version: 00 serial: 00:02:8a:78:6a:44 width: 32 bits clock: 33MHz capabilities: pm vpd bus_master cap_list rom ethernet physical wireless logical configuration: broadcast=yes driver=airo latency=64 maxlatency=4 mingnt=4 multicast=yes wireless=IEEE 802.11-DS Thanks, any help would be greatly appreciated!

  Read the article

• Need multiple sound outputs to multiple speakers

  - by Usman Sajeel Haider

  How do I play 3 different music tracks at the same time on my computer, such that song1 is played in speaker1, song2 in speaker2... Is this possible programatically? What additional hardware will I need? Do I need 3 seperate sound cards? Given that the hardware is in place, how would I "route" the sound output for a particular song to a particular speaker. Alternatively, is there a special hardware that can handle multiple inputs and outputs? Appreciate your expert opinions.

  Read the article

• How do you assign commands to keys in Terminal?

  - by NES

  Is there a solution to assign special key combinations to words in terminal use. For example the less command is very usefull and i use i a lot to pipe the output of another process through it. The idea would be to set up special key combinations that are only active in terminal use assigned to write different commands? So pressing CTRL + l in terminal window could write | less or CTRL + G could stand for | grep Note: i just mean adding the letters to commandline not execute the finally. A similar way what's tabcompletion but more specific.

  Read the article

• Why won't USB 3.0 external hard drive run at USB 3.0 speeds?

  - by jgottula

  I recently purchased a PCI Express x1 USB 3.0 controller card (containing the NEC USB 3.0 controller) with the intent of using a USB 3.0 external hard drive with my Linux box. I installed the card in an empty PCIe slot on my motherboard, connected the card to a power cable, strung a USB 3.0 cable between one of the new ports and my external HDD, and connected the HDD to a wall socket for power. Booting the system, the drive works 100% as intended, with the one exception of throughput: rather than using SuperSpeed 4.8 Gbps connectivity, it seems to be falling back to High Speed 480 Mbps USB 2.0-style throughput. Disk Utility shows it as a 480 Mbps device, and running a couple Disk Utility and dd benchmarks confirms that the drive fails to exceed ~40 MB/s (the approximate limit of USB 2.0), despite it being an SSD capable of far more than that. When I connect my USB 3.0 HDD, dmesg shows this: [ 3923.280018] usb 3-2: new high speed USB device using ehci_hcd and address 6 where I would expect to find this: [ 3923.280018] usb 3-2: new SuperSpeed USB device using xhci_hcd and address 6 My system was running on kernel 2.6.35-25-generic at the time. Then, I stumbled upon this forum thread by an individual who found that a bug, which was present in kernels prior to 2.6.37-rc5, could be the culprit for this type of problem. Consequently, I installed the 2.6.37-generic mainline Ubuntu kernel to determine if the problem would go away. It didn't, so I tried 2.6.38-rc3-generic, and even the 2.6.38 nightly from 2010.02.01, to no avail. In short, I'm trying to determine why, with USB 3.0 support in the kernel, my USB 3.0 drive fails to run at full SuperSpeed throughput. See the comments under this question for additional details. Output that might be relevant to the problem (when booting from 2.6.38-rc3): Relevant lines from dmesg: [ 19.589491] xhci_hcd 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 19.589512] xhci_hcd 0000:03:00.0: setting latency timer to 64 [ 19.589516] xhci_hcd 0000:03:00.0: xHCI Host Controller [ 19.589623] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 12 [ 19.650492] xhci_hcd 0000:03:00.0: irq 17, io mem 0xf8100000 [ 19.650556] xhci_hcd 0000:03:00.0: irq 47 for MSI/MSI-X [ 19.650560] xhci_hcd 0000:03:00.0: irq 48 for MSI/MSI-X [ 19.650563] xhci_hcd 0000:03:00.0: irq 49 for MSI/MSI-X [ 19.653946] xHCI xhci_add_endpoint called for root hub [ 19.653948] xHCI xhci_check_bandwidth called for root hub Relevant section of sudo lspci -v: 03:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30) Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f8100000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] #18 Kernel driver in use: xhci_hcd Kernel modules: xhci-hcd Relevant section of sudo lsusb -v: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 3 bMaxPacketSize0 9 idVendor 0x1d6b Linux Foundation idProduct 0x0003 3.0 root hub bcdDevice 2.06 iManufacturer 3 Linux 2.6.38-020638rc3-generic xhci_hcd iProduct 2 xHCI Host Controller iSerial 1 0000:03:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection TT think time 8 FS bits bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Device Status: 0x0003 Self Powered Remote Wakeup Enabled Full, non-verbose lsusb: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 011 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 003: ID 04d9:0702 Holtek Semiconductor, Inc. Bus 009 Device 002: ID 046d:c068 Logitech, Inc. G500 Laser Mouse Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 006: ID 174c:5106 ASMedia Technology Inc. Bus 003 Device 004: ID 0bda:0151 Realtek Semiconductor Corp. Mass Storage Device (Multicard Reader) Bus 003 Device 002: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 006: ID 1687:0163 Kingmax Digital Inc. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 046d:081b Logitech, Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Full output: full dmesg full lspci full lsusb

  Read the article

• Update problems due to "installation of packages from not authenticated sources" error

  - by Denis Hoss

  I have some problems updating my Ubuntu Requires installation of untrusted packages The action would require the installation of packages from not authenticated sources. cinnamon gir1.2-muffin-3.0 libgnome-keyring-common libgnome-keyring0 libmuffin0 muffin-common The downloads are from the Main server, the Source code under Ubuntu Software tab is marked Is there something I have missed? The output of sudo apt-get update is: W: GPG error: http://ppa.launchpad.net oneiric Release: The following signatures couldn't be verified because the public key is not available: NO_PUBKEY 6A9653F936FD5529 W: GPG error: http://ppa.launchpad.net oneiric Release: The following signatures couldn't be verified because the public key is not available: NO_PUBKEY A777609328949509 W: Duplicate sources.list entry http://archive.canonical.com/ubuntu/ oneiric/partner i386 Packages (/var/lib/apt/lists/archive.canonical.com_ubuntu_dists_oneiric_partner_binary-i386_Packages)

  Read the article

• SpriteBatch.Begin() making my model not render correctly

  - by manning18

  I was trying to output some debug information using DrawString when I noticed my model suddenly was being rendered like it was inside-out (like the culling had been disabled or something) and the texture maps weren't applied I commented out the DrawString method until I only had SpriteBatch.Begin() and .End() and that was enough to cause the model rendering corruption - when I commented those calls out the model rendered correctly What could this be a symptom of? I've stripped it down to the barest of code to isolate the problem and this is what I noticed. Draw code below (as stripped down as possible) GraphicsDevice.Clear(Color.LightGray); foreach (ModelMesh mesh in TIEAdvanced.Meshes) { foreach (Effect effect in mesh.Effects) { if (effect is BasicEffect) ((BasicEffect)effect).EnableDefaultLighting(); effect.CurrentTechnique.Passes[0].Apply(); } } spriteBatch.Begin(); spriteBatch.DrawString(spriteFont, "Camera Position: " + cameraPosition.ToString(), new Vector2(10, 10), Color.Blue); spriteBatch.End(); GraphicsDevice.DepthStencilState = DepthStencilState.Default; TIEAdvanced.Draw(Matrix.CreateScale(0.025f), viewMatrix, projectionMatrix);

  Read the article

• How can I use two video cards to power three screens?

  - by notatoad

  I have two Radeon 6450 graphics cards in my computer, with three screens. Only the screens plugged into the first graphics card are recognized and configurable in the displays setting panel. How can I use the displays plugged into my second graphics card? Both cards are present in lspci: 01:00.0 VGA compatible controller: ATI Technologies Inc NI Caicos [AMD RADEON HD 6450] 01:00.1 Audio device: ATI Technologies Inc NI Caicos HDMI Audio [AMD RADEON HD 6450] 02:00.0 VGA compatible controller: ATI Technologies Inc NI Caicos [AMD RADEON HD 6450] 02:00.1 Audio device: ATI Technologies Inc NI Caicos HDMI Audio [AMD RADEON HD 6450] I'm using the open source driver instead of the proprietary driver because the proprietary driver won't output 1440x2560.

  Read the article

• unable to add new repositories [closed]

  - by MuffinStateWide

  Possible Duplicate: How to I fix software center after installing the Linux Mint MATE desktop? please help , im unable to add new repositories below is the output when i try to confirm the action (sudo add-apt-repository ppa:[address here] Traceback (most recent call last): File "/usr/bin/add-apt-repository", line 98, in <module> sp = SoftwareProperties(options=options) File "/usr/lib/python2.7/dist-packages/softwareproperties/SoftwareProperties.py", line 96, in __init__ self.reload_sourceslist() File "/usr/lib/python2.7/dist-packages/softwareproperties/SoftwareProperties.py", line 580, in reload_sourceslist self.distro.get_sources(self.sourceslist) File "/usr/lib/python2.7/dist-packages/aptsources/distro.py", line 91, in get_sources raise NoDistroTemplateException("Error: could not find a " aptsources.distro.NoDistroTemplateException: Error: could not find a distribution template any help would be great , ive recently uninstalled MATE if thats any contribution to fixing this thanks in advance

  Read the article

• A record point not working

  - by Peter

  I'm trying to do an A record point to transfer the hosting of a domain from one provider to another. I don't want to change the nameservers as this will result in emails going down. The output when I dig for the domain shows the correct IP (78.46.63.87) for the new host. I know A records can take a while to propagate but Its been over 36hrs now and I still keep getting this error(below) when I try to pull the domain through as an addon domain via Cpanel on the new host. Are the old nameservers conflicting with the A record point? here's the error: Using nameservers with the following IPs: 208.80.125.4,208.80.126.4,208.80.124.4,208.94.148.4 Sorry, the domain is already pointed to an IP address that does not appear to use DNS servers associated with this server. Please transfer the domain to this servers nameservers or have your administrator add one of its nameservers to /etc/ips.remotedns and make the proper A entries on that remote nameserver.

  Read the article

• overriding implemented base class methods

  - by user793468

  I read somewhere that the chain of inheritance breaks when you alter a behavior from derived class. What does "altering a behavior" mean here? Is overriding an already implemented method in base class considered as "altering behavior"? Or, does the author mean altering method signatures and the output? Also, I ready Duplicating code is not a good practice, and its a maintenance nightmare. Again, does overriding an already implemented method in base class considered "Duplicating code"? If not, what would be considered as "Duplicating code"? I

  Read the article

• Problems after distribution update

  - by Avariya

  I have Ubuntu 11.10. Yesterday I make some distribution updates with Update Manager. And now I can't start my Ubuntu. Video related: http://www.youtube.com/watch?v=nn2MT9h2muQ (you need 25th sec) 1. Starting Ubuntu(output on video) 2. Black screen 3. Then permanent dark gray screen Was related problem with updating from 11.04 to 11.10. Ufter that update Ubuntu not start too and I must reinstall Ubuntu. Help me pls and ask questions if needed.

  Read the article

• fglrx installation without success - gl_conf issue

  - by Lucio

  I followed the steps of this guide. I've installed the drivers without any problems with sudo dpkg -i fglrx*.deb. The next step is Generate a new /etc/X11/xorg.conf file, but I can't do this due to the following reason: When I enter sudo aticonfig --initial -f the terminal show me this output: sudo: aticonfig: command not found This problem is caused by an error with the symbolics links into the fglrx directory. Look at this section, where you can see -how to fix it- but it doesn't work for me. Why it doesn't? Because after I enter sudo update-alternatives --auto gl_conf the terminal show me this: update-alternatives: error: no alternatives for gl_conf. What I have to do to fix this problem? GC: ATI RadeonHD 6670

  Read the article

• ETL Software Research Question

  - by WernerCD

  Where I work, we use an in-house ETL solution that's homegrown and has been around for 5-10 years. I'm still new to my data analysis job, but I was wondering about the ETL tools that are out there. This is a new area for me. My situation, and job, is basically digging in a set of databases (DB2, SQL2005, Citrix, Ancient Cobol Database with a SQL Wrapper on top, MySQL, etc). Gather the desired information. combine the different datasets into one set. output into a file of choice (CSV, Tab Separated, Pipe Separated, XLS, etc). FTP to customer. I guess what my real question is, given my job, what are some good ETL suites that I can look at and compare to my in-house tools? This is more to research some other options. Ultimately, I'd either suggest a new solution or get options/ideas to improve our current app.

  Read the article

• Associating Palettes with View TopComponents

  - by Geertjan

  A side effect of changes in NetBeans Platform 7.1 in the NetBeans window system is that palettes can now be created for view TopComponents. Below, a TopComponent in the "explorer" position is selected, which results in the Palette opening and showing items that can be dragged into the TopComponent: And here, in the same application, a TopComponent in the "output" position is now selected, which causes the Palette to open, showing items that are relevant to the TopComponent: I copied code used in the above two TopComponents from this blog entry: https://blogs.oracle.com/geertjan/entry/simple_component_palette Related issue: http://netbeans.org/bugzilla/show_bug.cgi?id=209238

  Read the article

• dpkg returns error 10 when processing package php5-common

  - by Jesse

  I'm having trouble installing php in 13.04. Seems like the package manager can't (re)configure the php package. I already tried purging every php* package, removing the cache files in /var/cache/aptbut and other solutions I've found but nothing seems to work. Here's the error output: $ sudo dpkg --configure -a Setting up php5-common (5.4.9-4ubuntu2.3) ... dpkg: error processing php5-common (--configure): subprocess installed post-installation script returned error exit status 10 Errors were encountered while processing: php5-common sudo apt-get install -f sudo apt-get install php5-common php5 they all return the same error. How can I fix this?

  Read the article

• How do I get my RTL8192ce based wireless device working properly?

  - by JonnyTruelove

  I am using the rtl8192cu chipset (on a Belkin wireless USB adapter N300) combined with 64 bit architecture and the 3.8 kernel. Some of you may know that this doesn't work. I tried this fix - RTL8188CU USB Network Adaptor on ubuntu 13.04 and now my internet is super slow. I am totally new to Ubuntu and I am concerned I do not have the right driver. The "stock" driver was the RTL8192cu, but it didn't connect 99% of the time and if it did the upload speed was higher than the download. Right now I am connecting through my laptop with a crossover cable, so my internet connection is just fine in my apartment. Relevant output from lsusb is here: Bus 002 Device 002: ID 050d:2103 Belkin Components F7D2102 802.11n N300 Micro Wireless Adapter v3000 [Realtek RTL8192CU] (bonus question: is that [050d:2103] the actual physical address straight from the hardware? Or does it change when I put different drivers on it? I am concerned I do not have the right driver)

  Read the article

• Ethernet not working in 12.04 (Dell Inspiron 14z)

  - by Izabela

  When I plug in a network cable, it is not recognized. The WI-FI is working properly, though. ifconfig output: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1645 errors:0 dropped:0 overruns:0 frame:0 TX packets:1645 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:206840 (206.8 KB) TX bytes:206840 (206.8 KB) wlan0 Link encap:Ethernet HWaddr e0:06:e6:de:57:e7 inet addr:150.164.201.145 Bcast:150.164.201.255 Mask:255.255.255.0 inet6 addr: 2001:12f0:601:a921:98a2:3dd:3be8:c483/64 Scope:Global inet6 addr: 2001:12f0:601:a921:e206:e6ff:fede:57e7/64 Scope:Global inet6 addr: fe80::e206:e6ff:fede:57e7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:23892 errors:0 dropped:0 overruns:0 frame:0 TX packets:14676 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:30123226 (30.1 MB) TX bytes:2189050 (2.1 MB)

  Read the article

• How to get differents backgrounds for each desktop working properly?

  - by MaikoID

  I've followed all the instructions for getting differents wallpapers for each desktop. I'm using Ubuntu 10.10. I've installed compiz-fusion-plugins-extra to add Wallpaper plugin on my Compiz Settings Manager (ccsm). But unfortunaly I cannot get my wallpapers working properly. I follow these instructions http://ubuntuguide.net/different-wallpapers-on-each-workspace-in-ubuntu and I just get a black background. Everything works fine after I press Win+P (I don't know what is this shortcut, refresh output I guess) or switch between ttf1 and ttf8 (ctrl+alt+f1 and ctrl+alt+f8). I tried reboot but the problem persist. What can I do to resolve this issue ?

  Read the article

• Upload Recordings Of The Problem To Your SR

  - by Irina

  Do you find yourself trying several times to explain a problem in a Service Request? Does the support engineer ask more than once for clarification? If so, you might be interested in DITO -- Demo It To Oracle. DITO uses CamStudio (free download!) to record the exact nature of the problem, and upload the output to your SR. The following articles provide more details: Working with Support - MOSSOS (Doc ID 1265130.1) "Demo It To Oracle" (DITO) - CamStudio Help ( Doc ID 11.1) Why take up valuable time first explaining the problem, then trying to get a web conference setup to show exactly what is going on? The next time you file an SR, try including a recording showing exactly which application is failing, where it is failing, and what it looks like when it fails.

  Read the article

< Previous Page | 435 436 437 438 439 440 441 442 443 444 445 446  | Next Page >