Search Results

Search found 2053 results on 83 pages for 'signal'.

Page 44/83 | < Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >

• A design for watching IPTV anywhere in the house?

  - by Carlos

  I'm currently getting TV and internet via IP to my house. The service comes into an ISP-supplied Router (ST585) which is in turn connected to an IPTV box. I need to replace the router, as it's port forwarding seems to be broken, so I was thinking of getting a box with an IGMP proxy. I once mistakenly got a non-IGMP box, with the result that the internet worked, but the IPTV didn't. The trouble is, I have no idea how to set up the IPTV part of the installation. I do have a copy of the ST585 configuration, but it doesn't look anything like the Cisco stuff that I learned about at CCNA. What are the steps necessary to reproduce the IGMP setup? I was thinking of WireSharking the communications on the network, but I suppose I'd need a hub for that? As a bonus, since the packets are coming in with the TV signal, is it possible to mess with the IGMP setup so I can watch TV anywhere in the house?

  Read the article

• Why does my wifi fail to stay connected?

  - by Mark0978

  We have 5 different laptops in the house, 1 macbook, 1 Compaq, 3 dells, plus numerous little devices like ipods, squeezeboxs, squeezebox radios and controllers, you name it. All of them connect to and stay connected to the "downstairs" WIFI just fine. But my laptop (the most expensive of the lot) refuses to stay connected, preferring the much weaker and slower signal upstairs. My laptop is running Win7 (64 bit) Ultimate with an Intel 3945ABG WIFI contoller (It's a Dell Precision M6300). The WIFI Access Point is a Cisco WRT54G2 V1 with firmware: Firmware: DD-WRT v24-sp2 (10/10/09) micro Time: 11:11:10 up 42 min, load average: 0.06, 0.01, 0.00 WAN: Disabled

  Read the article

• How to identify cause of system lock on debian squeeze?

  - by David Sanders

  I have a desktop system at work with debian squeeze installed. Every couple days or so, when I come in in the morning, the system appears to be asleep and won't wake up. I suspect it goes into power save mode and then doesn't receive the wake up signal when I click the mouse or touch the keyboard. Does anyone know where I should look in order to start tracking this down? Like log files, etc? I doubt it, but maybe the fact that I'm using a mac aluminum usb keyboard and a wireless usb mouse (that has an off switch) has something to do with it? Maybe, when I turn my mouse off at the end of the day, the system loses track of the device somehow? I dunno :P. Thanks in advance.

  Read the article

• How do I configure additional phone lines asterisk/trixbox?

  - by Matt

  I have a 4 port Digium card in there, and have 4 lines running smoothly. Now, we added ANOTHER 4 port card and have 4 more analog lines coming into the Trixbox server. It still runs the 4 fine, but what do I need to do to add the additional 4 phone numbers/lines? I want it to act exactly as before, there's nothing special about the new lines. We just need more lines so that when we have 4 out of state customers call, we can have 4 more call and not get the busy signal. Trixbox CE 2.8

  Read the article

• No picture on HDMI Output from a Pioneer 921 AV Receiver to a Projector

  - by Alexey Kulikov

  I am trying hard to tackle a what seemed to be simple problem if wiring my setup together. The setup: Mac Mini (2011) with HDMI Output Pioneer 921 K AV Receiver Acer HD Projector (HDMI) When I hook up my Mac Mini directly to the Projector with a 30 foot (10 meter) HDMI Cable everything is just fine. The picture is sharp and the colors brilliant. However, when I send HDMI to the receiver (into the BD HDMI Input) then I get absolutely no HDMI output to the projector, it keeps saying "no signal". Is there perhaps some magic combination of setup buttons that may help me resolve this problem?

  Read the article

• kill SIGABRT does not generate core file from daemon started from crontab.

  - by Guma

  I am running CentOS 5.5 and working on server application that sometimes I need to force core dump so I can see what is going on. If I start my server from shell and send kill SIGABRT, a core file is created. If I start same program from crontab and then I send the same signal to it the server is "killed" but no core file is generated. Does any one know why is that and what need to be added to my code or changed in system settings to allow core file generation? Just a side note I have ulimit set to unlimited in /etc/profile I have set kernel.core_uses_pid = 1 kernel.core_pattern=/var/cores/%h-%e-%p.core in /etc/sysctl.conf Also my server app was added to crontab under same login id as I am running it from shell. Any help greatly appreciated

  Read the article

• IDE Motherboard to Boot from a SATA 1T Hdd

  - by JavaMan

  I want to use my SATA HDD in my very old ASUS A7V8X-X motherboard (made in 2003). I intended to buy a cheap adapter for this. Say something similar to this one: http://www.cooldrives.com/satoidecofor.html But would there be any issue if I want to boot from this SATA drive? My impression is that these kind of adapters convert SATA signal and commands to PATA directly and such a low level conversion should be transparent to the motherboard and BIOS - in case the BIOS doesn't support SATA. And, for my motherboard, it sure doesn't. Does anyone ever used such a kind of adapter to support a boot drive? Any success sorry?

  Read the article

• how to troubleshoot shutdown problems in windows 7

  - by Ieyasu Sawada

  I have a desktop with windows 7 ultimate installed. Whenever I shut it down from the start button. The text that says that it is logging off and shutting down is present and the monitor blacks out and says no signal. But the lights in the RAM is still on and all the fans in the desktop is still spinning. Why is that? It seems like its not shutting down completely. I have also got disk problems lately. Event id 175 and 50. Which I think is caused by the computer not shutting down completely. How do I troubleshoot this one? Feel free to ask if you need more details, thanks.

  Read the article

• Second monitor not detected

  - by Gabriel

  Hi I have two VGA monitors, my GPU is ATI PowerColor 6850 which has two DVI slots, I use adapters for both VGA monitors. If I connect any the two monitors in the first slot it will work right away (along the plugin confirmation sound). And if I connect any of both monitors to the second slot I won't get anything, nor a signal or confirmation sound. I also tried auto detecting via Catalyst Control Center and Windows Desktop Resolution. I have the latest drivers installed. EDIT: I found this on the Spec Description: Display Connectors DL-DVI-I/SL-DVI-D And in NewEgg: 2 x DVI (1 Single Link, 1 Dual Link) Could this have anything to do with my issue?

  Read the article

• What is causing my internet to be slow on one laptop but not the other and only at a distance?

  - by Matt Case

  I have a newer laptop, purchased within the last year (acer aspire 7740). This laptop does not have any problem connecting to wireless networks and indicates that the signal strength is excellent on most of the wireless networks I connect to. When the laptop is within 10 feet of my wireless router it gets 30 down 10 up. When it is farther away than 10 feet it will be lucky to get 3 down and 1 up. I also have an older laptop, purchased in 2005, that has no problems at all at the same range. None of my phones, gaming consoles or tablets have this problem. I am beginning to think that the problem must be some hardware defect with the wireless card. I can provide additional information if needed. Just thought I'd check to see what others thought because I've been working on computers my whole life and have never heard of this happening. I have also tried to change the channels on my wireless router and have had no success with this idea.

  Read the article

• How to watch disk free space change on Linux?

  - by Bob

  As the title implies, I want to know how to watch disk free space change on Linux instead polling it periodically via statfs. When the free space is changed, a signal is emitted to allow the application having a chance to handle the change event. On Windows, it can be done by FindFirstChangeNotification with FILE_NOTIFY_CHANGE_SIZE. When the free space is changed, the HANDLE object returend by FindFirstChangeNotification gets signaled and let application do something. Is there any similar way to do that on Linux? Thanks.

  Read the article

• Bridging two connections in windows 7

  - by Serban Razvan

  I have recently bought an Samsung UE32ES5500 and I want to connect it to the internet. Not wanting to buy an expensive Samsung wireless adapter for the TV, I've decided to use an ethernet cable. Because the Internet cable passes through underground to the bedroom and the TV is located in the living room, i decided to put a router in the bedroom, and receive it's signal in the living room using a windows 7 laptop. Afterwards I connected the laptop to the TV through an ethernet cable, and bridged the two connections in Network Connections in Control Panel on the laptop. The TV successfully finds the laptop (and the router I think) but still cannot connect to the internet. Does anyone knows a solution to this problem? (the connections must be bridged because I want to have only one network in the house)

  Read the article

• Have to reset wireless frequently on iPad / Macs connected to Cisco WRV200

  - by retailevolved

  I have a Cisco WRV200 set up in our small office. The wireless signal works great for PCs, but I have found that Macs and iPads have to frequently reset the connection. It will be working for about 10 minutes, then stop. To fix it, I just turn off Airport and turn it on again. On an iPad, I have to go into settings, shut the wireless off, and then turn it on again. The router is broadcasting mixed B/G on channel 6. Security is WPA-PSK2. Anybody out there had similar issues with their router? How can I fix it?

  Read the article

• Media Center is sending duplicate #'s when changing channels

  - by Robert

  I recently switched from cable to DirecTV (satellite). I went through the "Set up TV signal" in Media Center, and I went through the manual setup of the remote as it didn't recognize the DirecTV remote. All seemed okay, except sometimes (often - about 1/2 the time) when I select a channel in Media Center's guide it sends 5527 instead of 527 or 5446 instead of 546 - so it doesn't change the channel correctly. (I see the numbers show up on the TV screen before the channel changes.) I tried re-learning the remote, but the problem is still there. (Media Center is changing channels through the IR Blaster attached to the front of the DirecTV box.)

  Read the article

• FreeBSD 8 and Samba 3.3 smb_panic

  - by scraft3613

  What is causing samba to crash? Need help diagnosing ... [2010/06/14 16:11:42, 0] lib/fault.c:fault_report(40) =============================================================== [2010/06/14 16:11:42, 0] lib/fault.c:fault_report(41) INTERNAL ERROR: Signal 11 in pid 951 (3.3.8) Please read the Trouble-Shooting section of the Samba3-HOWTO [2010/06/14 16:11:42, 0] lib/fault.c:fault_report(43) From: http://www.samba.org/samba/docs/Samba3-HOWTO.pdf [2010/06/14 16:11:42, 0] lib/fault.c:fault_report(44) =============================================================== [2010/06/14 16:11:42, 0] lib/util.c:smb_panic(1673) PANIC (pid 951): internal error [2010/06/14 16:53:40, 0] smbd/server.c:main(1274) Edit: A bit more info -- log.smbd: [2010/06/14 15:59:02, 0] smbd/server.c:main(1274) smbd version 3.3.8 started. Copyright Andrew Tridgell and the Samba Team 1992-2009 [2010/06/14 15:59:02, 0] printing/print_cups.c:cups_connect(103) Unable to connect to CUPS server localhost:631 - Connection refused [2010/06/14 15:59:02, 0] printing/print_cups.c:cups_connect(103) Unable to connect to CUPS server localhost:631 - Connection refused smb.conf [global] workgroup = WASH netbios name = PROD1 [media] path = /jon/media read only = no guest ok = yes

  Read the article

• How to set up Asus RT-N66U in bridge mode with wired connection to main router?

  - by Milligan

  I have a wired router (TP-Link RT-860) in the basement where the cable service comes in. Eight wired ethernet connections span two buildings. I currently have a Linksys wireless router set up in bridge mode, but its signal doesn't span the whole area. I have purchased an Asus RT-N66U to replace it, but I can't figure out how to set it up in bridge mode. Does anyone know if this is possible? Second question: Would there be any advantage in installing DD-WRT on the Asus?

  Read the article

• Trouble with external monitor under Windows 7 on MacBook Pro Boot Camp

  - by Colm

  I'm running Windows 7 32-bit on a mid-2010 15" MacBook Pro Intel Core i5 under Boot Camp. I've had trouble getting it to work with my second display and searching Google for an appropriate answer has failed me. I'm on the latest version of Boot Camp - 3.2 - and have updated the drivers for the NVIDIA GeForce GT 330M. The monitor is connected via a VGA cable, and is a Dell ST2410. The monitor is recognised by Windows, which knows it's a Dell and its resolution. The desktop should be extended onto the second monitor - however nothing is showing. It remains black, though it doesn't show a lack of signal coming through which I would have expected. Any ideas what's wrong?

  Read the article

• Why do I have no TTY on a basic Ubuntu 9.10 server install?

  - by pr1001

  I have reinstalled Ubuntu 9.10 Server several times on a bog standard 1RU server and each time I finish the install and reboot I see GRUB run and am then presented with a black screen. The machine is running just fine, as I am able to SSH in, but I can't see anything on the attached monitor. I have a simple LCD screen connected via VGA and a signal is apparently being output to it, as it doesn't go asleep. Looking at /var/log/syslog I see: Mar 24 14:57:44 bridge5 rsyslogd-2039: Could no open output file '/dev/xconsole' [try http://www.rsyslog.com/e/2039 ] However, I later see: Mar 24 14:57:44 bridge5 kernel: [ 0.001368] console [tty0] enabled Any thoughts? Thanks!

  Read the article

• Cannot connect to internet with Clearwire modem.

  - by ide

  I'm currently using a Motorola WiMAX modem (CPEi 25725) and cannot connect to the internet. I can connect to the modem at 192.168.15.1 and check its status. It says that it has good/excellent connectivity to the internet and shows all five signal bars. Additionally it has sent and received some WiMAX packets so I believe it is connected to a tower. I'm at a loss for what the problem is. Unplugging the modem, restarting it from software, and restarting my computer (Windows 7) have not helped. Windows still reports that it is not connected to the internet. Alternatively, could this be an ISP issue? I have heard that Clearwire is a not-so-reputable ISP that blocks VoIP, and I was using Skype recently.

  Read the article

• DVI problem with LG L204WT

  - by Holgerwa

  I have a LG L204WT which has VGA and DVI connectors. Until recently, I have used the monitor via VGA, but now I have upgraded the graphics board and switched to DVI. The problem is that each time after the computer starts, the monitor either doesn't show anything (black screen, but doesn't go into standby) or the picture is distorted. I then switch the monitor off and on several times, and at some point it starts correctly and then I can work as usual. This only happens on startup. It is one out of 3 monitors, the other two work fine. It seems to me as if the monitor is not able to synchronize on the DVI signal and either shows a distorted picture or nothing at all. There are no settings in the monitor setup that would change anything. What could be the problem?

  Read the article

• How can you convert audio (3.5mm) to S/PDIF?

  - by SSumner

  I have a monitor that I want to use as my 'TV' for my gaming system. I connect it via HDMI, so sound and video go through the monitor, but I want sound to my headphones, which travels via optical (S/PDIF) cable. The monitor (Dell U2713HM) has a 3.5mm audio jack on it for line out, but I couldn't find anything that simply plugs in an converts the analog audio signal to a digital one so I can plug in a S/PDIF cable. What sort of device do I need to do this? (I am not asking for shopping recommendations, merely what options allow this conversion. I would prefer the smallest option, as space is limited).

  Read the article

• Share ADSL Internet connection between two computers 40 meters away (straight) from each other

  - by dario_ramos

  I have a box with a working ADSL Internet connection. About 40 meters away (straight), in another house, there is another, older box. There are two houses in between. Would there be some practical way to supply an Internet connection to the older box? The neighbors are ok with us installing cables and stuff. I'd say wifi would not be practical, since the houses in between would weaken the signal too much. And using Ethernet cables might require a switch or router in between, due to Ethernet distance limitations. Advice?

  Read the article

• Suggestion of device WiFi range in it's spec. Possible?

  - by SeeR

  I have router Draytek Vigor 2100VG at home almost in the center of it. The farthest point at my home is my balcony, ~12m from it. I have constant wifi signal range problems with some of my devices, but not with others. Notebook Lenovo W510 - no problems Nokia Home Music - always on 10m - no problems Sony PS3 - always on 7m - no problems Sony tablet S - problems around 6m Sony PSP - problems around 8m Sony PS Vita - problems around 8m Nokia E63 - problems around 8m I'm curious why my Notebook don't have any problems even on the balcony? I guess it has better hardware or uses more power for transmission. This information is really important when you want to buy new device/computer, so my real question is: Can device wifi range can somehow be found/suggested from official hardware technical specification? If not Is there some web page with wifi range reviews?

  Read the article

• No sigal showing on LCD TV when Conects Leptop via VGA Cable [migrated]

  - by Amit Prajapati

  I am trying to connect my laptop to Samsung LCD TV by VGA TO HDMI cable My Laptop find Samsung tv on display setting. But When I press fn+F7 key my TV display No Signal My laptop specifications are: "Lenovo R61 ThinkPad, Model: 8935AE7 Window7 Ultimate 32 bits 2GB RAM VGA Port available No HDMI Port My TV specification are: Samsung LCD 26 HDMI Port available VGA Port Available I want to know what is problem? When I connect Another Dell Laptop (Window7 32 bit) with HDMI to HDMI cable it work properly. Thanks in Advance!

  Read the article

• after power outage, monitor won't turn on

  - by J82

  I had a power outage in my apartment today during a Windows 7 SP1 update. I installed SP1 and it told me to restart so I did and that's when the power outage happened. After the power came back on, I started the computer and it looks like the computer is running normally but my monitor is not getting a signal. I am using a Wacom Cintiq 21UX. I tried unplugging all the cords and plugs in the power strip and turning it back on. I also tried a strange method I read in another thread of removing the power cord, holding the on button for 30 seconds, putting the power cord back in, and turning it on. Still no dice. How can I get my monitor to turn on? please help..

  Read the article

< Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >