Search Results

Search found 47818 results on 1913 pages for 'super cat'.

Page 44/1913 | < Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >

• Ubuntu 9.10 Only Sees 244 MB RAM, while BIOS and Windows Sees 1.5 GB

  - by nicorellius

  I have 1.5 GB of RAM installed on an older Dell, Pentium 4. I just installed Ubuntu 9.1 and the system is only seeing 244 MB of RAM, even though there is 1.5 GB on the system. The BIOS sees all of it. I ran a Knoppix disc and it only saw 25 MB upon booting. I made no particular changes to the installation taht would affect this. I looked through the BIOS and the only setting I could see was the AGP aperture. Not even sure what this is. Anyone know where I went wrong? I also tried moving the memory modules around on the board. Booted with the 1 GB stick, still saw 244 MB. NOTE - This same system, except for the hard drive, had Windows XP running on it. The user who ran it said that the RAM was good and always showed 1.5 GB. Here is sudo cat /proc/meminfo MemTotal: 250064 kB MemFree: 3832 kB Buffers: 13356 kB Cached: 52216 kB SwapCached: 19676 kB Active: 91504 kB Inactive: 113884 kB Active(anon): 60572 kB Inactive(anon): 82156 kB Active(file): 30932 kB Inactive(file): 31728 kB Unevictable: 0 kB Mlocked: 0 kB HighTotal: 0 kB HighFree: 0 kB LowTotal: 250064 kB LowFree: 3832 kB SwapTotal: 4883720 kB SwapFree: 4781204 kB Dirty: 496 kB Writeback: 720 kB AnonPages: 123796 kB Mapped: 23368 kB Slab: 17248 kB SReclaimable: 7932 kB SUnreclaim: 9316 kB PageTables: 5304 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 5008752 kB Committed_AS: 740372 kB VmallocTotal: 770600 kB VmallocUsed: 26008 kB VmallocChunk: 662544 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 4096 kB DirectMap4k: 114128 kB DirectMap4M: 147456 kB

  Read the article

• pam debugging "check pass; user unknown"

  - by lvc

  I am attempting to get Prosody authenticating with its auth_pam module. It is configured to use the pam service name xmpp. The pam.d/xmpp file is copied straight from the one configured for dovecot (originally taken from, I think, dovecot's documentation), which is known to be working: # cat /etc/pam.d/xmpp auth required pam_unix.so nullok debug account required pam_unix.so debug Logging in with dovecot works wonderfully. Logging in with prosody, with exactly the same username and password, causes Prosody to return 'Not authorized', and the following in journalctl -f: Oct 29 22:12:14 riscque.net prosody[9396]: c2s1d010b0: Client sent opening <stream:stream> to riscque.net Oct 29 22:12:14 riscque.net prosody[9396]: c2s1d010b0: Sent reply <stream:stream> to client Oct 29 22:12:14 riscque.net prosody[9396]: [178B blob data] Oct 29 22:12:14 riscque.net unix_chkpwd[9408]: check pass; user unknown Oct 29 22:12:14 riscque.net prosody[9396]: pam_unix(xmpp:auth): conversation failed Oct 29 22:12:14 riscque.net prosody[9396]: pam_unix(xmpp:auth): unable to obtain a password Oct 29 22:12:14 riscque.net prosody[9396]: pam_unix(xmpp:auth): auth could not identify password for [lvc] Oct 29 22:12:14 riscque.net prosody[9396]: riscque.net:saslauth: sasl reply: <failure xmlns='urn:ietf:params:xml:ns:xmpp-sasl'><not-authorized/><text>Unable to authorize you with the authentication credentials you&apos;ve sent.</text></failure> This series of errors seems mutually contradictory - first it says "user unknown", but then that it can't obtain the password for lvc - this username certainly exists on the system. What is likely going on here, and how would I debug this further?

  Read the article

• Laptops with easy heat sink service?

  - by Niten

  Can you recommend a current laptop model with easy heat sink access – or better yet, a removable air intake filter – making it easy to periodically clean out the dust and lint that always packs up in these things? Every laptop I've owned has eventually overheated on account of a clogged heat sink. (I suppose it doesn't help that I have a cat who loves to hang out where I'm working, or that my laptop is almost always running.) One of the things I really love about my current system, a Dell Inspiron 1420n, is how easy it is to service its cooling system: whenever I notice the fan starting to work harder and the CPU temperature climbing higher than it should be, I merely have to unscrew a single panel from the bottom of the machine, clean out the heat sink, and then I'm good for another few months. Which current models of the "business laptop" variety offer similar easy cooling system service? I'm looking for something roughly along the lines of: 14- or 15-inch display Nehalem-based CPU Solid construction – magnesium chassis or better (like the Inspiron) TPM (for BitLocker) ideal, but not mandatory Docking adapter ideal, but not mandatory Good battery life For example, the ThinkPad T410 would have been my top choice, but it seems like it would be a serious chore to service its heat sink. For the current MacBook Pros it looks downright impossible. No matter how nice the laptop is in other respects, it'll be of no use to me when it's overheating. So, any suggestions? Thanks in advance... (I'm constantly surprised that customers and manufacturers don't pay more attention to this feature, at least in the business laptop subcategory. In the last couple months I've fixed two friends' laptops which were also overheating due to clogged cooling systems; clearly I'm not the only one affected by this.)

  Read the article

• Networking Home Office

  - by Matt

  I'm in the process of building an office in my garden. It's about 25m away from my house. I'd like to run a wired network connection to the office. I'd rather not go down the powerline route, as speeds don't seem great, and I'm likely to want to be moving a lot of data around on the internal network. I have an electrician who is running armoured electrical cable to the office, and is providing conduit for me to run network cable. My questions are: 1) What type of cable to run 2) How I terminate/connect it at both ends I could get something like armoured cat6 utp solid core (like this: http://www.netstoredirect.com/cat6-cable/289166-external-armoured-cat6-utp-solid-cable-price-per-metre.html) which seems fairly robust, but then I have to terminate it. Additionally, where the cable enters my house, there is about another 15m to where my router is situated. I also read this artice: http://www.audioholics.com/audio-video-cables/bjc-cat-network-cable-quality-interview which scared me into realising I don't know what I'm doing!! particularly with termination. Or I could get an "cat6 external patch cable" (e.g http://www.netstoredirect.com/rj45-network-cables/239231-external-cat6-utp-ldpe-rj45-patch-leads.html) and run that in the conduit, and work out how to terminate it at the house end. At the office end I guess I can just plug it into a switch. Any help? Thanks

  Read the article

• Failed to mount to nfs server with "Program not Registered"

  - by Farrel

  I'm trying to setup nfs server on Fedora 17 and I'm getting "Program not Registered" error when I'm trying to mount. I guess the main reason for this is rpcbind. I'm a newbie in linux, so I don't know what info should I provide you with. Here is some info that might be useful. rpcinfo -p program vers proto port service 100000 4 tcp 111 portmapper 100000 3 tcp 111 portmapper 100000 2 tcp 111 portmapper 100000 4 udp 111 portmapper 100000 3 udp 111 portmapper 100000 2 udp 111 portmapper 100005 1 udp 20048 mountd 100005 1 tcp 20048 mountd 100005 2 udp 20048 mountd 100005 2 tcp 20048 mountd 100005 3 udp 20048 mountd 100005 3 tcp 20048 mountd 100024 1 udp 42223 status 100024 1 tcp 50054 status cat /etc/exports /home/Farrel/prog 192.168.xxx.xxx (ro,sync) service nfs status Redirecting to /bin/systemctl status nfs.service nfs-server.service - NFS Server Loaded: loaded (/usr/lib/systemd/system/nfs-server.service; enabled) Active: active (exited) since Fri, 02 Nov 2012 09:29:04 +0300; 5min ago Process: 924 ExecStartPost=/usr/lib/nfs-utils/scripts/nfs-server.postconfig (code=exited, status=0/SUCCESS) Process: 909 ExecStart=/usr/sbin/rpc.nfsd $RPCNFSDARGS ${RPCNFSDCOUNT} (code=exited, status=0/SUCCESS) Process: 885 ExecStartPre=/usr/sbin/exportfs -r (code=exited, status=0/SUCCESS) Process: 864 ExecStartPre=/usr/lib/nfs-utils/scripts/nfs-server.preconfig (code=exited, status=0/SUCCESS) CGroup: name=systemd:/system/nfs-server.service Warning: Journal has been rotated since unit was started. Log output is incomplete or unavailable. Firewall is disabled on both systems. I spent a lot of time reading on the topic but all manuals on setting up nfs server lead to "Program not Registered" error. Any how-to-fix-it ideas?

  Read the article

• How can find the USB wireless adapter into the dmesg log file?

  - by AndreaNobili

  I am pretty new in Linux (RaspBian for RaspBerry Pi but I think that there are not difference) and I have to install an USB wireless network adapter (the product is the TP-Link TL-WN725N, this one: http://www.tp-link.it/products/details/?model=TL-WN725N ) Now, I think that this is not automatically recognized by my system because if I execute ifconfig command I obtain the following output: pi@raspberrypi ~ $ ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:2a:9f:b0 inet addr:192.168.1.8 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:424 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:34195 (33.3 KiB) TX bytes:89578 (87.4 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So now it see only my ethernet network interface and not the wireless. So I was thinkig to try to see into the dmesg, but I don't know what have I to see and how to select it into the dmesg output. For example by the following command I can see the line of the dmesg log file relate to my ethernet port: pi@raspberrypi ~ $ cat /var/log/dmesg |grep -i eth [ 3.177620] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:2a:9f:b0 [ 18.030389] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 19.642167] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 But what can I try to search for the USB wireless adapter? Tnx

  Read the article

• VNC error: "Could not connect to session bus: Failed to connect to socket"

  - by GJ

  I started a vncserver on display :1 on an ubuntu machine. When I connect to it, I get a grey X window with an error message Could not connect to session bus: Failed to connect to socket. The vnc log is: Xvnc Free Edition 4.1.1 - built Apr 9 2010 15:59:33 Copyright (C) 2002-2005 RealVNC Ltd. See http://www.realvnc.com for information on VNC. Underlying X server release 40300000, The XFree86 Project, Inc Sun Mar 20 15:33:59 2011 vncext: VNC extension running! vncext: Listening for VNC connections on port 5901 vncext: created VNC server for screen 0 error opening security policy file /etc/X11/xserver/SecurityPolicy Could not init font path element /usr/X11R6/lib/X11/fonts/Type1/, removing from list! Could not init font path element /usr/X11R6/lib/X11/fonts/Speedo/, removing from list! Could not init font path element /usr/X11R6/lib/X11/fonts/misc/, removing from list! Could not init font path element /usr/X11R6/lib/X11/fonts/75dpi/, removing from list! Could not init font path element /usr/X11R6/lib/X11/fonts/100dpi/, removing from list! cat: /var/run/gdm/auth-for-link2-eGnVvf/database: No such file or directory gnome-session[24880]: WARNING: Could not make bus activated clients aware of DISPLAY=:1.0 environment variable: Failed to connect to socket /tmp/dbus-FhdHHIq8jt: Connection refused gnome-session[24880]: WARNING: Could not make bus activated clients aware of GNOME_DESKTOP_SESSION_ID=this-is-deprecated environment variable: Failed to connect to socket /tmp/dbus-FhdHHIq8jt: Connection refused gnome-session[24880]: WARNING: Could not make bus activated clients aware of SESSION_MANAGER=local/dell:@/tmp/.ICE-unix/24880,unix/dell:/tmp/.ICE-unix/24880 environment variable: Failed to connect to socket /tmp/dbus-FhdHHIq8jt: Connection refused Sun Mar 20 15:34:10 2011 Connections: accepted: 0.0.0.0::51620 SConnection: Client needs protocol version 3.8 SConnection: Client requests security type VncAuth(2) VNCSConnST: Server default pixel format depth 16 (16bpp) little-endian rgb565 VNCSConnST: Client pixel format depth 16 (16bpp) little-endian rgb565 gnome-session[24880]: Gtk-CRITICAL: gtk_main_quit: assertion `main_loops != NULL' failed gnome-session[24880]: CRITICAL: dbus_g_proxy_new_for_name: assertion `connection != NULL' failed Any ideas how to fix it?

  Read the article

• can't properly shutdown ubuntu and sound problem on HP mini 311 netbook

  - by Viele

  hi, I recently bought a HP mini 311 netbook. I replaced its harddrive and installed ubuntu 10.04. Since then, I have encountered some very strange problem with its sound and shutdown/reboot. At times, when I start the computer, it will have no sound, on the GUI the sound is at max, but no sound is available. This sometimes also happen after after upgrades, hibernate, and toggling the wireless radio button. Strangely, when the sound is out the device will also refuse to be shutdown. If I shutdown the computer using the GUI, it will simply go back to the log in screen without actually shutting down. If I use "sudo shutdown 0", the computer will hang on the loading screen of the shut down process. I had to force the pc to shutdown by holding the power button down. usually (probably always) after I force a turn-off then start off again. the sound and shutdown become normal. I wonder if anyone have clues regarding to the cause of this problem. This the info about the computer: 1) installed ubuntu 10.04LTS RC, later upgraded to formal released version. 2) cat /proc/asound/version == "Advanced Linux Sound Architecture Driver Version 1.0.21." however, when doing 'alsaconf' the version displayed is 1.0.23 any help is appreciated. Thanks

  Read the article

• How to extract terms from an HTML document

  - by bookcasey

  I have a HTML document filled with terms that I need to put into a spreadsheet. They follow this basic pattern: <ul> <li class="name"><a href="spot.html">Spot</a></li> <li class="type">Dog</li> <li class="color">Red</li> </ul> <ul> <li class="name"><a href="mittens.html">Mittens</a></li> <li class="type">Cat</li> <li class="color">Brown</li> </ul> <ul> <li class="name"><a href="squakers.html">Squakers</a></li> <li class="type">Little Parrot</li> <li class="color">Rainbow</li> </ul> It's very consistent. I need to extract the string within the li.name a (so, "Spot") but only if the type is "Dog" or "Parrot", and put them in a spreadsheet. I've been trying to use Sublime Text's ability to Find with regex, but I'm really struggling, and since regex and HTML usually don't play nice, I was wondering if there is a better and easier way to accomplish this. Thanks.

  Read the article

• Join mp4 files in linux

  - by Jose Armando

  I want to join two mp4 files to create a single one. The video streams are encoded in h264 and the audio in aac. I can not re-encode the videos to another format due to computational reasons. Also, I cannot use any gui programs, all processing must be performed with linux command line utilities. FFmpeg cannot do this for mpeg4 files so instead I used MP4Box e.g. MP4Box -add video1.mp4 -cat video2.mp4 newvideo.mp4 unfortunately the audio gets all mixed up. I thought that the problem was that the audio was in aac so I transcoded it in mp3 and used again MP4Box. In this case the audio is fine for the first half of newvideo.mp4 (corresponding to video1.mp4) but then their is no audio and I cannot navigate in the video also. My next thought was that the audio and video streams had some small discrepancies in their lengths that I should fix. So for each input video I splitted the video and audio streams and then joined them with the -shortest option in ffmpeg. thus for the first video I ran avconv -y -i video1.mp4 -c copy -map 0:0 videostream1.mp4 avconv -y -i video1.mp4 -c copy -map 0:1 audiostream1.m4a avconv -y -i videostream1.mp4 -i audiostream1.m4a -c copy -shortest video1_aligned.mp4 similarly for the second video and then used MP4Box as previously. Unfortunately this didn't work either. The only success I had was when I joined the video streams separetely (i.e. videostream1.mp4 and videostream2.mp4) and the audio streams (i.e. audiostream1.m4a and audiostream2.m4a) and then joined the video and audio in a final file. However, the synchronization is lost for the second half of the video. Concretelly, there is a 1 sec delay of audio and video. Any suggestions are really welcome.

  Read the article

• Broken fonts in Konsole KDE 4.3.4

  - by depesz

  I have a strange situation - after some upgrades a couple of days ago fonts in KDE Konsole broke. To make it more specific - standard fonts look more or less OK, but when I use my national characters (like acelnsózz) they all look broken - like from another font, or badly scaled. The same problem doesn't exist in GNOME Terminal. I usually use the Terminus font, so I used this for demonstration, but it shows in other fonts as well - if that will be necessary I will provide list. Konsole shot: GNOME Terminal shot: As for my settings: =$ cat /etc/X11/xorg.conf Section "Device" Identifier "Builtin Default intel Device 0" Driver "intel" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Screen" Identifier "Builtin Default intel Screen 0" Device "Builtin Default intel Device 0" Monitor "Monitor0" EndSection Section "InputDevice" Identifier "touchpad" Driver "synaptics" Option "CorePointer" EndSection Section "ServerLayout" Identifier "Builtin Default Layout" Screen "Builtin Default intel Screen 0" InputDevice "touchpad" EndSection =$ xdpyinfo | grep -E resolution\|dimensions dimensions: 1680x1050 pixels (444x277 millimeters) resolution: 96x96 dots per inch I tried forcing DPI in system settings (to 120), or adding monitor size to xorg.conf - so far nothing helped. Any idea on what should I do to make it work sanely again?

  Read the article

• NFS high CPU usage

  - by user269836

  Hello, I have a very strange issue. I have next server: Intel(R) Xeon(TM) MP CPU 3.16GHz cat /proc/cpuinfo | grep proce | wc -l 8 free -m total used free shared buffers cached Mem: 28203 27606 596 0 10789 9714 -/+ buffers/cache: 7103 21100 Swap: 24695 0 24695 RAID card *-storage description: RAID bus controller product: MegaRAID vendor: LSI Logic / Symbios Logic physical id: 7 bus info: pci@0000:13:07.0 logical name: scsi2 version: 01 width: 32 bits clock: 66MHz capabilities: storage pm bus_master cap_list rom configuration: driver=megaraid latency=32 resources: irq:134 memory:d8ff0000-d8ffffff(prefetchable) memory:df600000-df60ffff(prefetchable) HDD: 10x148Gb SCSI U320 15k - RAID5 /dev/sdb1 807G 674G 93G 88% /storage /dev/sdb1 /storage ext4 defaults,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,noatime,nodiratime,noacl,errors=remount-ro 0 1 network cards ethtool -i eth0 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ethtool -i eth1 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ifconfig bond0 Link encap:Ethernet HWaddr 00:0f:1f:ff:d6:4d inet addr:192.168.15.71 Bcast:192.168.15.255 Mask:255.255.255.0 inet6 addr: fe80::20f:1fff:feff:d64d/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:1062818202 errors:0 dropped:3918 overruns:0 frame:0 TX packets:1041317321 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10000 RX bytes:258867684559 (241.0 GiB) TX bytes:396569192650 (369.3 GiB) this server running only nfs-kernel-server uname -a Linux nas2-backup 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux Debian 6. What do I have, once per day or two, LA goes up, it can be reached around LA: 40 but if I do: nfs-kernel-server restart. Every thing is OK. But on the next day or a little bit later, LA goes up again. Servers are connected to d-link dgs 1016d with 24 GBits ports. I have tried everything to find out what the problem is. Why it's happening, but still I can not resolve this issue. Any ideas on what is happening here?

  Read the article

• How can I find the USB wireless adapter into the dmesg log file?

  - by AndreaNobili

  I am pretty new in Linux (RaspBian for RaspBerry Pi but I think that there are not difference) and I have to install an USB wireless network adapter (the product is the TP-Link TL-WN725N, this one: http://www.tp-link.it/products/details/?model=TL-WN725N ) Now, I think that this is not automatically recognized by my system because if I execute ifconfig command I obtain the following output: pi@raspberrypi ~ $ ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:2a:9f:b0 inet addr:192.168.1.8 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:424 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:34195 (33.3 KiB) TX bytes:89578 (87.4 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So now it see only my ethernet network interface and not the wireless. So I was thinkig to try to see into the dmesg, but I don't know what have I to see and how to select it into the dmesg output. For example by the following command I can see the line of the dmesg log file relate to my ethernet port: pi@raspberrypi ~ $ cat /var/log/dmesg |grep -i eth [ 3.177620] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:2a:9f:b0 [ 18.030389] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 19.642167] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 But what can I try to search for the USB wireless adapter? Tnx

  Read the article

• Bootable GRUB partition

  - by MA1

  I have a customized live fedora 12 USB which is working fine. What i want to do is to make a partition of my hard disk bootable so that my customized fedora can be run from hard disk. To accomplish this i did the following steps: Created a primary partition(/dev/sda2) and format it as ext3 and set it as active. Copy all the files in the live usb to /dev/sda2. Following are the live usb contents(all directories): a. boot b. EFI c. LiveOS d. syslinux Then i installed the GRUB in boot/grub Created the grub.conf in boot/grub Following are the contents of each directory in the USB: syslinux/ boot.cat isolinux.bin splash.jpg vesamenu.c32 initrd0.img ldlinux.sys syslinux.cfg vmlinuz0 LiveOS/ livecd-iso-to-disk osmin.img squashfs.img EFI/ boot/ boot.conf grub.conf boot.efi bootia32.conf bootia32.efi splash.jpg splash.xpm.gz vesamenu.c32 initrd0.img isolinux.bin isolinux.cfg vmlinuz0 boot/grub/ core GRUB files grub.conf olpc.fth Following are contents of grub.conf default=0 splashimage=/EFI/boot/splash.xpm.gz timeout 2 hiddenmenu title funLinux kernel /EFI/boot/vmlinuz0 root=live:LABEL=myFun rootfstype=auto ro liveimg quiet ssb.blacklist=1 selinux=0 vga=normal nomodeset rhgb initrd /EFI/boot/initrd0.img Now when i try to boot from the hard disk it shows the grub menu and fedora starting to load but during loading it said No root device found Boot has failed, sleeping forever So, where is the problem? what i am doing wrong?

  Read the article

• Broken fonts in konsole kde 4.3.4

  - by depesz

  I have strange situation - after some upgrade couple of days ago fonts in KDE konsole broke. To make it more specific - standard fonts look more or less ok, but when I use my national characters (like acelnsózz) they all look broken - like from another font, or badly scaled. The same problem doesn't exist in gnome-terminal. I usually use Terminus font, so I used this for demonstration, but it shows in other fonts as well - if that will be necessary I will provide list. Konsole shot: gnome-terminal shot: As for my settings: =$ cat /etc/X11/xorg.conf Section "Device" Identifier "Builtin Default intel Device 0" Driver "intel" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Screen" Identifier "Builtin Default intel Screen 0" Device "Builtin Default intel Device 0" Monitor "Monitor0" EndSection Section "InputDevice" Identifier "touchpad" Driver "synaptics" Option "CorePointer" EndSection Section "ServerLayout" Identifier "Builtin Default Layout" Screen "Builtin Default intel Screen 0" InputDevice "touchpad" EndSection =$ xdpyinfo | grep -E resolution\|dimensions dimensions: 1680x1050 pixels (444x277 millimeters) resolution: 96x96 dots per inch I tried forcing DPI in system settings (to 120), or adding monitor size to xorg.conf - so far nothing helped. Any idea on what should I do to make it work sanely again?

  Read the article

• CentOS - mdadm raid1 drive won't mount to default location

  - by danny

  I'm running CentOS 5.5, the system, boot, swap, etc. is all on /dev/sda and I have two identical single-partition drives /dev/sdb1 /dev/sdc1 that are configured in RAID1 (using mdadm). It was working fine (configured to mount to /mnt/data in the fstab file) and I recently let yum install a couple of automatic updates without paying attention to what they were, and now it doesn't work. Raid is working fine (dmesg shows it gets loaded correctly). mdstat shows: # cat /proc/mdstat Personalities : [raid1] md0 : active raid1 sdc1[1] sdb1[0] XXXX blocks [2/2] [UU] unused devices: <none> Additionally, I can mount it anywhere other than its default directory (i.e. the following works, and I can read data off the drives). # mount /dev/md0 /mnt/data2 EXT3-fs warning: mounting fs with errors, running e2fsck is recommended But when I run the following I get: # mount -a mount: /dev/sdb1 already mounted or /mnt/data busy It says nothing is mounted when I try to umount /dev/sdb1 or umount /mnt/data, so I assume it's the second of those errors. However, lsof | grep mnt shows nothing. The weird thing is that I can save files in /mnt/data. So something is obviously mounted there, but when I try to umount it I get the error that nothing is mounted. /etc/mtab doesn't mention any of the partitions or files I am trying to work with, and fstab just has that one line I mentioned above that is supposed to mount my raid partition. Again, it was all working fine until I On Google I've found a few things about dmraid interfering with mdadm after an update, but I yum remove'd dmraid and rebooted and it didn't help. I'm really confused and need to get this working to get on with my work!

  Read the article

• Restrict SSH user to connection from one machine

  - by Jonathan

  During set-up of a home server (running Kubuntu 10.04), I created an admin user for performing administrative tasks that may require an unmounted home. This user has a home directory on the root partition of the box. The machine has an internet-facing SSH server, and I have restricted the set of users that can connect via SSH, but I would like to restrict it further by making admin only accessible from my laptop (or perhaps only from the local 192.168.1.0/24 range). I currently have only an AllowGroups ssh-users with myself and admin as members of the ssh-users group. What I want is something that works like you may expect this setup to work (but it doesn't): $ groups jonathan ... ssh-users $ groups admin ... ssh-restricted-users $ cat /etc/ssh/sshd_config ... AllowGroups ssh-users [email protected].* ... Is there a way to do this? I have also tried this, but it did not work (admin could still log in remotely): AllowUsers [email protected].* * AllowGroups ssh-users with admin a member of ssh-users. I would also be fine with only allowing admin to log in with a key, and disallowing password logins, but I could find no general setting for sshd; there is a setting that requires root logins to use a key, but not for general users.

  Read the article

• Advanced Linux file permission question (ownership change during write operation)

  - by Kent

  By default the umask is 0022: usera@cmp$ touch somefile; ls -l total 0 -rw-r--r-- 1 usera usera 0 2009-09-22 22:30 somefile The directory /home/shared/ is meant for shared files and should be owned by root and the shared group. Files created here by usern (any user) are automatically owned by the shared group. There is a cron-job taking care of changing owning user and owning group (of any moved files) once per day: usera@cmp$ cat /etc/cron.daily/sharedscript #!/bin/bash chown -R root:shared /home/shared/ chmod -R 770 /home/shared/ I was writing a really large file to the shared directory. It had me (usera) as owning user and the shared group as group owner. During the write operation the cron job was run, and I still had no problem completing the write process. You see. I thought this would happen: I am writing the file. The file permissions and ownership data for the file looks like this: -rw-r--r-- usera shared The cron job kicks in! The chown line is processed and now the file is owned by the root user and the shared group. As the owning group only has read access to the file I get a file write error! Boom! End of story. Why did the operation succeed? A link to some kind of reference documentation to back up the reason would be very welcome (as I could use it to study more details).

  Read the article

• Linux: How do I remove bootchart from the boot process?

  - by java.is.for.desktop

  Hello, everyone! I have OpenSUSE 11.2. I removed bootchart and forgot to run mkinitrd. Now, right at the start of the boot process, I get boot/93-bootchart.sh: line 17: 462 Terminated stopinitrd 5 I Can't find any 93-bootchart.sh anywhere. Failsafe boot mode doesn't help. Earlier I got an error message about non existing /sbin/bootchartd, but I just copied /bin/cat to /sbin/bootchartd using a GParted boot disk. I tried to use chroot with an OpenSUSE boot disk, but mkinitrd can't find the root device, which is there actually (/dev/sda5). How can I make my system boot again? EDIT Ok, now I managed to re-install the bootchart rpm, using OpenSUSE boot disk and chmod. The system starts again. But that annoying bootchart is still there. I will not try again to remove it. First I will try to figure out, how to disable it during the boot process. Hopefully with your help ;)

  Read the article

• Is there any free software to check for issues with a DVD drive?

  - by AgentConundrum

  I don't usually play movies on my laptop (prefer the standalone with the tv), but I tried to watch one the other night, and noticed playback was really choppy and had audio artifacts in places. I thought it could be related to memory issues so I rebooted and tried again, but the results were the same. I considered that it could be an issue with the disc, so I tried to clean it but again there was no change. I don't think the problem is with the disc, because I tried another disc and it also had the same problem. I don't think I've ever watched the second disc since I've had it, so it should have been safe in its jewel case. Also, there were no issues when I watched an episode off the first disc in my standalone player. What I'm wondering is: are there are any (free) utilities that can check for issues with the drive itself? I looked around but most of the software I found focuses on integrity checks for the disc, not the drive. I have had issues with this laptop recently (had to replace the keyboard when the cat damaged it while I was cleaning dust out and the machine was ripped apart, also replaced part of the chassis after I cracked it when I tried to open it not knowing a screw was still in it) so I may have just replaced the drive incorrectly. I'm going to check on this while I await an answer to this question. Thanks.

  Read the article

• LG W3000H-BN monitor cannot go above 1280x800

  - by Jo Profit

  I noticed that there are many people complaining about this issue with the W3000H but I have yet to find a solution that works for me. I am using Windows 7 Professional and and using a nVidia Quadro NVS 240 video card with a 4 monitor splitter cable. The cable from the monitor and the splitter are rated DVI-D Dual Link and the video card itself is rated for 2560x1600. I have installed the latest drivers for the video card and just grabbed the .inf, icm and cat file from the LG website and manually installed the monitor drivers. Does anyone have problems with the same setup? I have 3 other monitors (2 at 1920x1080 and 1 at 1280x1024). I really would like to be able to display the full resolution or else the large screen is useless. (I triple checked that the monitor itself supports this resolution). So monitor, cable, splitter and card supposedly support 2560x1600. Drivers are up to date but I cannot select that resolution when in the "Screen Resolution" menu, nor through the nVidia control panel. Please save me from madness :)

  Read the article

• Authenticate VNC session with ConsolKit?

  - by lori

  I have a linux machine running Fedora 16 in a cupboard. It has no screen or keyboard. I connect to it using a combination of vnc and ssh. Recently, after an update, I have had issues with authentication on the machine. If I vnc to it, the kde desktop pops up an error dialog every few minutes saying Authorization failed. Failed to obtain authentication. If I plug in a USB drive it fails to mount, Dolphin reports an authentication issue again. I have had limited success finding the solution. AFAICT, it is an issue with ConsoleKit deeming me to be a non-local user so it prevents authentication. This is the output from ck-list-sessions: $ ck-list-sessions Session5: unix-user = '1000' realname = 'steve' seat = 'Seat6' session-type = '' active = FALSE x11-display = ':1' x11-display-device = '' display-device = '' remote-host-name = '' is-local = FALSE on-since = '2012-09-16T08:07:03.137011Z' login-session-id = '1' I have tried to update my .vnc/xstartup script to include ck-launch-session as follows: $ cat ~/.vnc/xstartup #!/bin/sh exec ck-launch-session vncconfig -iconic & unset SESSION_MANAGER unset DBUS_SESSION_BUS_ADDRESS export XKL_XMODMAP_DISABLE=1 OS=`uname -s` if [ $OS = 'Linux' ]; then case "$WINDOWMANAGER" in *gnome*) if [ -e /etc/SuSE-release ]; then PATH=$PATH:/opt/gnome/bin export PATH fi ;; esac fi if [ -x /etc/X11/xinit/xinitrc ]; then exec ck-launch-session /etc/X11/xinit/xinitrc fi if [ -f /etc/X11/xinit/xinitrc ]; then exec ck-launch-session sh /etc/X11/xinit/xinitrc fi [ -r $HOME/.Xresources ] && xrdb $HOME/.Xresources exec ck-launch-session xsetroot -solid grey exec ck-launch-session xterm -geometry 80x24+10+10 -ls -title "$VNCDESKTOP Desktop" & exec ck-launch-session twm & This has not helped. How can I either authenticate myself to ConsoleKit, or trick it into believing I am a local user?

  Read the article

• GRUB reporting wrong partition type

  - by plok

  It all started when I had to replace one of the disks that the software RAID 1 on this machine currently uses. From that moment on I have not been able to boot to the Windows XP that is installed on the fourth hard drive, /dev/sdd. I am almost positive that the problem is related not to Windows but to GRUB, as if I unplug all the other hard drives so that the Windows XP disk is now /dev/sda it boots with no problem. The problem seems to be that GRUB detects a wrong partition type, which I understand suggest that something is really messed up. This is what I get when I try to follow the steps that until now had worked like a charm: grub> map (hd0) (hd3) grub> map (hd3) (hd0) grub> root (hd3,0) Filesystem type is ext2fs, partition type 0xfd 0xfd? That doesn't make sense. /dev/sdb and sdc are 0xfd (Linux raid), but not /dev/sdd: edel:~# fdisk -l [...] Disk /dev/sdd: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00048d89 Device Boot Start End Blocks Id System /dev/sdd1 * 1 30400 244187968+ 7 HPFS/NTFS edel:/boot/grub# cat device.map (hd0) /dev/sda (hd1) /dev/sdb (hd2) /dev/sdc (hd3) /dev/sdd I have been trying to work this out for hours, to no avail. Can anyone point me in the right direction?

  Read the article

• How do I hook into Tar with BASH?

  - by orb

  Long Story Short I am working with Tar archives that contain PNG images in base64 encoding. I would like to use BASH (or whatever else works) to hook into the extraction function of Tar to decode PNG images from base64 encoding to standard PNG encoding after the files are unpacked. A simple cat $input-file | base64 -d >$output-file will successfully decode the images. Is there a way I can hook into tar -xf so that users do not have to do any (or minimal) extra work to decode the images? In the GNU Tar documentation (http://www.gnu.org/software/tar/manual/html_chapter/Backups.html#SEC97) I found that there are in fact variables reserved to hold the names of functions I desire to be hooked into various moments in Tar program execution. However, the documentation explains that these variables, along with other variables that can be set to configure Tar, are located in a file named backup-specs. Unfortunately, the path to this file is not given. Further, running sudo find / -name backup-specs tells me that this file is not present on my Ubuntu version 13.04 system. Background Information not included in the Long Story Short I have been working on a browser-based (WebGL) particle effect creation application (http://www.particleeffect.org), (https://github.com/cgrabowski/webgl-particle-effect-editor), (https://github.com/cgrabowski/webgl-particle-effect). I have began to write a client-side-only solution for saving and loading effect data as a tar archive. However, since client-side JavaScript has limited capability to process binary data, the images used as textures in the effect are saved with base64 encoding. I have been able to implement saving effect data as a Tar archive (haven't pushed that to Github yet). However, the images present in said Tar archive cannot be manipulated unless they are decoded from base64 encoding.

  Read the article

• Why does my DSDT table is different from what I found online?

  - by Hao Shen

  I have found a field in DSDT table where I want to modify from here http://www.ztex.de/misc/c2ctl.e.html Generally, I want to modify the _PSS field about the processor so that I can have more frequency levels available in the CPUfreq driver interface. I try to use this command to dissemble the DSDT table from my Desktop(Linux2.6.29,Intel CORE 2): cat /proc/acpi/dsdt > dsdt.aml iasl -d dsdt.aml Then I have a file dsdt.dsl as following(very long, so I just show the beginning of the file): /* * Intel ACPI Component Architecture * AML Disassembler version 20090123 * * Disassembly of dsdt.aml, Mon May 6 20:41:40 2013 * * * Original Table Header: * Signature "DSDT" * Length 0x00003794 (14228) * Revision 0x01 **** ACPI 1.0, no 64-bit math support * Checksum 0x46 * OEM ID "DELL" * OEM Table ID "dt_ex" * OEM Revision 0x00001000 (4096) * Compiler ID "INTL" * Compiler Version 0x20050624 (537200164) */ DefinitionBlock ("dsdt.aml", "DSDT", 1, "DELL", "dt_ex", 0x00001000) { Method (DBIN, 0, NotSerialized) { Noop } Scope (\) { Device (_SB.VBTN) ................... But I can not find the _PSS field as shown in the website I have given above. I do not know why? I am sure the current cpufreq driver shows 4 frequency levels available. So at least there should be something in the table showing this..right? Has anybody here played with the DSDT table before? Thanks,

  Read the article

< Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >