Search Results

Search found 16764 results on 671 pages for 'provider model'.

Page 440/671 | < Previous Page | 436 437 438 439 440 441 442 443 444 445 446 447  | Next Page >

• FreeNAS/ZFS/Raid-Z slightly different disks

  - by muskratt

  I'm considering using FreeNAS and "recycling" some of my older 1TB disks. Two are the exact same model Western Digital while another is Seagate and the fourth is Samsung. Typically, since all disks are not equal, I'll create my arrays on a Windows-based server 1GB undersized to prevent a replacement disk not being large enough. Dell is notorious for sending replacement SATA disks of different brand---knock on wood, no problems yet. Since not all drives are created equally and they can vary a few MBs, is there a way to make the the FreeNas/ZFS/Raid-Z function in the same way I do for my Windows-based servers above? Thanks

  Read the article

• Manual TRIM Windows 7 on OCZ VERTEX 2 SATA II 2.5" SSD

  - by INTPnerd

  I have an OCZ VERTEX 2 SATA II 2.5" SSD with Windows 7 Professional installed on it. I am pretty sure TRIM is not working because my motherboard is the Asus M2N-SLI (not the Deluxe model) which does not support AHCI mode for the drive. Is there a utility that is compatible with this drive that I could possibly run once a day that would do something similar to a manual TRIM in order to keep the drive performance up? I could not find one specifically for this drive on the OCZ website. I did find a User-Initiated Garbage Collection wiper tool, but it is for a Vertex drive not Vertex 2. I tried to run it, but it said that wiper could not be run for all the drives on this system.

  Read the article

• Windows XP/Firewall -- Can't open UDP port 9100 for JetDirect sharing

  - by Barton Chittenden

  I'm setting up my Dad's laptop (Vista) to print to an HP Deskjet printer attached to a Windows XP Desktop box. The XP box is running Windows firewall. Laptop sits on 192.168.1.66, Desktop 192.168.1.65. I set up logging in the firewall, and determined that it is dropping inbound packets on TCP port 9100, used by JetDirect, the printing protocol. I set up an exception on TCP port 9100, allowing access to the local subnet. There's also an entry under the 'allow applications' tab which was marked for the exact printer model. I selected this as well, then tried to print again... I see more dropped packets from 192.168.1.66 to 192.168.1.65 for TCP port 9100. What do I try next?

  Read the article

• My laptop suppose to have 6 GB ram but it's only 2 GB installed

  - by monablo

  My laptop is supposed to have 6 GB ram but it only detects 2 GB of it, so I don't know what to do. I searched the web for answer and what i get that there's 2 possible problem: 1- That 4 GB ram card is broken and not working 2- or the 2 ram card have a different path so the windows chose the path of the smaller ram card which would be the 2 GB ram I don't know what is the path in first place so I really don't know what to do. How would I troubleshoot, and work out why the 4 GB stick is not being detected? My laptop's specifications are as follows: Windows 7 Home premium 64- bit Operating system processor : intel (R) core(TM) i7 CPU Q740 @1.73 GHz 1.73GHz installed memory(RAM) : 2.00 GB (but it suppose to be 6 GB -_- ) My laptop is Dell and it's Model N5010

  Read the article

• Startech SVx41HDI Series Server Remote Control Usage Question - How do I switch away from a dead por

  - by tajh

  We have a Startech KVM over IP model SV841HDI and it was stuck pointing a port where the machine has been removed. We ended up having to physically plug something into that port in order to switch ports again, meaning that if someone in support accidentally switches to an empty port, we need to have a documented solution for making it useable again. The unit is old, no longer under warranty, firmware updates for it are no longer available (interestingly it runs a powerPC version of busybox). Since it does work well except for this one catch, we would like to avoid replacing it. Reading the manual, you have a several recommended methods. I tried them. Hit the left CTRL key a few times (as well as all the other popular KVM keys I could think of). The VNC GUI offers lots of buttons - none of them switch away from a dead port. The question is: how do I switch away from a dead port on this particular KVM remotely?

  Read the article

• Mac failing (failed?) hard drive - is all hope lost?

  - by Daniel

  It's a 500 GB Seagate laptop hard drive that came with my Macbook Pro. Apple partition format. Already replaced and now have it external, connected via SATA/USB adapter. Trying to get just a few files that I worked on while out of town when it crashed (and thus did not have my time machine backup drive). Drive will not mount, but OS X Disk Utility detects it and can read the capacity, model number, and even the name of the partition, which leads me to believe all hope may not be lost. Failed attempts so far: Disk Utility verify+repair says drive cannot be repaired and that I should back up immediately (lovely) Disk Warrior says it cannot rebuild the directory due to hardware failure Data Rescue quick & deep scans immediately failed PhotoRec says "error reading sector" for every sector (at least for the few minutes I let it run before closing it to explore other options) What else can I try here? Again, I'm just looking for a few, small files (python scripts to be specific) - not a full recovery.

  Read the article

• Using a CF card as an IDE HDD

  - by dartacus

  I have an old Sony laptop (Vaio TR1-MP) that I like. The HDD has died and since it's a hard-to-find 1.8" IDE hard drive I'm considering buying one of those little CF card adaptors and a 16gb CF card. The total cost of that is about £30 and replacement HDDs for this model are far pricier. Has anyone replaced their HDD with a CF card in this way, and, crucially, is the performance utterly horrible afterwards? ;-) I've seen a couple of threads which hint it's possible but the advice eventually given was just to buy a SSD, but I'm not even sure if its possible to get a 1.8" SSD with an IDE connector that'll fit my laptop. (I freely admit that the most sensible thing to do would be to bin it and just buy a cheap netbook which would be smaller, faster and lighter than the sony, but it does have a very nice widescreen display and dammit I just like it !) Thanks, G

  Read the article

• Impossible do find motherboard drivers to Dell Dimension 3000

  - by Masziej

  Hello, I recently formatet and reinstalled XP on my girlfriends computer. Ive had this computer since 2001, never formatet it, until now =) Anyway the problem is that i cant find any drivers for the motherboard (integrated audio, video and ethernet). as i said its an old ass Dell. Cant remember if I got any cds along with it. Even if i did theyre gone a long time ago. So, I ran CPUZ and got this: --Motherboard-- Dell Computer Corp. Model 0K8980 And started googling. But didnt find any drivers. Still cant So im asking for a little help here. I really need to get the computer going before she wants a new one :D And yes i have looked on dells homesite, but they dont seem to wanna host drivers for their old stuff

  Read the article

• How to connect to my US network overseas via VPN?

  - by GiH

  I purchased an Apple TV for my parents and I have a netflix account. My parents live overseas, and I was wondering if they could use my account to get it to work. I read that it won't work unless you use proxies or a VPN, so I was wondering if its possible for me to setup a VPN to my network in the US instead of paying a service like StrongVPN? Setup: Router in US - Airport Extreme Router abroad - D-link (not sure of model) I know that the AppleTV doesn't have a built-in VPN client, maybe eventually when its jailbroken there will be an app, but as of now I'll have to use the routers right? Any other ideas are welcome as well!

  Read the article

• Why is Windows 7 so slow to log-on when my Wireless USB dongle is plugged in?

  - by Sam

  I'm using an Edimax Wireless USB dongle (model EW-7711UTN) on Windows 7 64-bit. The dongle works brilliantly (it was truly plug-and-play) except for one thing. I've noticed that if the dongle is plugged in whilst I'm logging on to Windows it introduces a massive delay - after I type in my password and hit enter, Windows shows the "Welcome" screen, then the screen goes black for 2 minutes or so (with just the cursor showing) before finally displaying my desktop. If I unplug the dongle before I enter my password, Windows goes straight to my desktop. Even though the dongle didn't appear to need drivers for Windows 7, I did try downloading the latest ones from the Edimax website, but that made no difference.

  Read the article

• printing in linux

  - by Neilvert Noval

  Hello all. I've been a linux user for quite some time. But haven't do printing until now. I just wanna ask how to do printing in linux? I have researched a bit on it. I found some $> echo "print me" > /dev/lp0, but unfortunately, I have no lp0 in my /dev. I don't know if this is the right thing to do. Nevertheless, please tell me of ways on how I can print from my linux box. Here are some details: OS: debian linux 5.0.4 printer: disclosed until it is necessary connection: usb connection So do i need to add a printer first? From the printer manual that I read, this printer model has no linux driver.

  Read the article

• Windows XP Pro 'Connect to' logon box greyed out with Guest

  - by HaydnWVN

  Have a machine i've just nuked and paved to be used in a public enviroment, yet still connected to a Workgroup. Would like it to prompt for a logon when accessing any of the network shares as different departments will be using it. It does prompt for a login but the username field is greyed out. Have disabled simple file sharing, disabled guest account, changed Local Security Policies (Network access Sharing and Security model to 'classic') all to no avail. A google around has lots of other people with the same issues, lots of 'fixes' with very few feedback. Of course none of these work for me! :)

  Read the article

• Laptop hot after format [migrated]

  - by Dany Khalife

  I recently formatted an HP G62 Laptop and installed all drivers from the HP site that should be installed for this model. But i noticed a very strange behavior, using Coretemp, the temp is always above 50 (on idle) and reaches 70 very quickly sometimes (Critical is 90) If i open youtube or skype alone, i can get temperatures as high as 83. Normally it was around 32 (on idle) and reaches 70 when i open games but not youtube.... I have a i3 processor and AMD graphics so i am wondering if somehow it's a graphics card issue (since i3 has integrated graphics as far as i know) Device manager shows only AMD graphics card tho, not sure if i3 graphics should appear here too. Any ideas what i might have forgotten to do after the format ?

  Read the article

• Upgrading HP DL185 G5 8LFF, is using a Dell J1520 4-Drop SATA Adapter possible?

  - by jpreed00

  The HP DL185 G5 8LFF model supports 8 3.5" drives and 1 optical drive. However, instead of the optical drive, I'd like to have 2x 2.5" drives instead. The problem is that the PSU has no more SATA power cables (even though the motherboard has 4 additional SATA data ports). The PSU does have a free 10-pin connector and it looks like the J1520 cable from Dell would fit the bill. Link to cable description Does anyone have any experience using these cables? Are they safe? Any other ideas for adding the disks to the server if I don't use the cable? Thanks!

  Read the article

• What's the best way to block IP spoofing on a layer 3 switch?

  - by toupeira

  We're hosting Dedicated Servers and are currently using old 3com switches with IP-based ACLs. So each port has an ACL that allows all IP addresses assigned to this customer, and blocks everything else. But now 3com was bought by HP, and the follow-up model only supports basic ACL that aren't flexible enough to both allow certain IPs while blocking others. Looking at other switches in a similar price-range, we've found that most of them have similar problems or don't offer any ACL features at all. I assume this could also somehow be done with VLANs, but if I understand this correctly we'd still need some kind of ACL to actually specify the valid IP addresses for each port. What do you use to make sure your customers don't use unassigned IP addresses? Or what switches can you recommend that have flexible ACL functionality?

  Read the article

• further troubleshooting on a p8z77 motherboard

  - by Journeyman Geek

  I just bought a brand now asus p8z77 motherboard with a intel 3770. Its currently not booting - the system powers up for half a second and then powers down, and the CPU error light shines. I've tried switching ram between slots, switching PSUs, updating the bios (which can be done sans processor or ram on this model). Power: The 8 pin power connector is definitely in place correctly, and I've tried swapping PSUs between a new seasonic m12, and a known good cheapie PSU Ram: Ram is in the recommended slot for single stick operation, and tried swapping between the two sticks of DDR3 I have. Processor: Its installed correctly as far as I can tell, no obvious bent pins on the motherboard. At this point I'm guessing I'll need to RMA something. Are there any 'definitive' tests I can try, short of swapping CPU and motherboard that would let me know it is the CPU? Can I actually trust the error light on the motherboard?

  Read the article

• No sigal showing on LCD TV when Conects Leptop via VGA Cable [migrated]

  - by Amit Prajapati

  I am trying to connect my laptop to Samsung LCD TV by VGA TO HDMI cable My Laptop find Samsung tv on display setting. But When I press fn+F7 key my TV display No Signal My laptop specifications are: "Lenovo R61 ThinkPad, Model: 8935AE7 Window7 Ultimate 32 bits 2GB RAM VGA Port available No HDMI Port My TV specification are: Samsung LCD 26 HDMI Port available VGA Port Available I want to know what is problem? When I connect Another Dell Laptop (Window7 32 bit) with HDMI to HDMI cable it work properly. Thanks in Advance!

  Read the article

• How to make a quiet laptop ? [closed]

  - by psihodelia

  Most modern laptops have very noisy fans. I am looking for a quiet laptop or a small stationary computer which has all its hardware built in a display. Most tasks will be pdf/docs processing, real-time audio processing, web-surfing and skype video chats. Certainly, there is no any fan-less model today; but maybe some of the existed laptops do not switch on their fans so often or implement different solutions? For example, an iPad has no fan at all and it is fast enough for my needs, but it has no normal operating system, so I can't use it for anything but audio chats and web-surfing. Or maybe I can buy a laptop and tweak it to make it absolutely noiseless? Can you recommend me any solution please? Thanks in advance!

  Read the article

• Can I connect my ipod's earphones to my computer?

  - by user1361315

  My computer (recent model Dell z600) has 2 input devices on the front of the computer, 1 has an icon of headphones and the other is a Mic icon. When I plugin my earphones to the input device that has the headphones, and play some sound I don't hear anything from my earphones (sounds comes from built in speakers). I know when I plugin a USB headphone set, it switches over to those on but for some reason my earphones are not being picked up. Is it not compatible? Note: my earphones look similar to http://www.hdaccessory.com/catalog/reprearphone.jpg

  Read the article

• How can the shared hosting server provide unlimited physical subdomains as opposed to unlimited virtual subdomains?

  - by xport

  Some hosting companies offer unlimited subdomains. There are two kind of subdomains: physical subdomains and virtual subdomains. A physical subdomains has its own site directory rather than being nested inside the site directory of its parent domain. A virtual subdomain site directory, on the other hand, is nested inside the site directory of its parent domain. I wonder how can the shared hosting company provide unlimited (theoritically) physical subdomains? In my understanding, each physical subdomain represents a new site (rather than a new application or virtual directory) in IIS. Please correct me if my mental model is wrong.

  Read the article

• Can't run monitor at native 1080p resolution on Windows 7

  - by Rex

  I have a 24" ViewSonic VX2453 monitor that supports 1920x1080p, connected using HDMI. However at that resolution, the desktop goes off the screen. Using the Nvidia control panel, I have to set it to a custom resolution of 1804x1014 to display correctly. The monitor has its drivers properly installed (the correct model name shows up in control panel after installing the drivers), and I'm running 64 bit Win7 Ultimate. I have a GeForce 560 Ti card, if that helps. Why does this happen?

  Read the article

• My Portable Hard Drive with USB3 didn't work when connected to My Laptop, but it working with USB2 properly

  - by Mohammad Hasan Esfahanian

  I have Western Digital My Passport Essential Portable Hard Drive with USB3 and Model:WDBACY5000ABK-EESN. Until about two or three months ago when I connected that to My Laptop USB3 port, that worked very well. But now when I'm connecting that to My device, The system does not detect any Hard Drives. When plug in the USB2 port is working properly. I connected that to another Laptop whit USB3 port but I had the same problem. I tested My Laptop port with a Flash Memory by USB3 and ports were healthy and I'm sure they are working. For this issue, I changed the windows, but it still did not work. What can I do? Thanks in advance.

  Read the article

• TextPad printing to incorrect printer

  - by TecBrat

  I have tried to find an answer on Google, and searched SU, but have not found anything on this particular issue. I Looked for a setting in the TextPad menu and didn't see anything that seemed relevant. I have 2 networked printers that are the same model. (HP LaserJet 2200 Series PCL 5) One is near me and the other is across the building. The one near me is my default. It seems that TextPad remembers the last printer used and defaults to it rather than printing to the system default, so when I force it to print to my default printer once, the problem is solved until I decide to print to the other printer for some reason. If I don't remember the problem, and specifically print a job to the nearby printer to correct it, I'll end up either wasting paper or wasting trips across the building to pick up printjobs that got printed there by accident. Has anyone else noticed this problem? Is there a solution?

  Read the article

• Recover Bios HP DV9700T windows 7 64

  - by petebob796

  I downloaded the latest DV9700t bios (.59) and ran the update tool in windows 7 64. This seemed to go ok and did the usual system will shutdown in 10 seconds dialog. Updon the reboot nothing happens I get no BIOS screen or anything so I think the bios update went wrong. Which I am annoyed about I have never known a bios update to fail before and lots of people on the internet seem to have had the same problem with the same model. There is a way to recover apparently using crisdisk utility and creating a bootable usb key then holding win+b at power on, unfortunately the utility to make the disk doesn't seem to work in 64 bit versions of windows, the only type I have easy access to. Anyone know a way to create the boot disk in 64?

  Read the article

• About Hard Disk Drive Docks

  - by Crossbrowser

  I'm thinking of buying a drive dock to put my unused large HDD to use. I will also probably use the dock to backup files and swap the drives regularly. I have a few questions though: Are they noisy? I plan to use them via USB (because I don't think I have eSata connectors), am I gonna want to kill myself every time I backup? (I know it's supposed to be 480 Mbps, but how realistic is this?) Do you recommend a particular model? (I was thinking about this Startech HDD dock) Thank you

  Read the article

< Previous Page | 436 437 438 439 440 441 442 443 444 445 446 447  | Next Page >