Search Results

Search found 2436 results on 98 pages for 'hdd cloning'.

Page 45/98 | < Previous Page | 41 42 43 44 45 46 47 48 49 50 51 52  | Next Page >

  • Laptop will not boot

    - by WillumMaguire
    This is a dell studio 1558 laptop. Now, something is wrong with the charger that it won't charge the laptop, but the laptop can turn on and operate properly as long as it is attached. It has been like this for a while, but it's not the problem. My problem is that as of yesterday, It takes several minutes to get past the "dell" startup logo (where is says "f2 setup" and "f12 boot options"). After it gets past, it beeps as normal to tell me about the charger and gives me the f2/f12 options and f1 to continue as normal. I can press f12 to get into boot options and load into my live USB BackTrack 5 ISO, but after "startx" it just stays at a black screen. I can also access BIOS setup, but see nothing that would help the problem. When I boot to the HDD, it gives me this Intel UNDI, PXE-2.1 (build 083) Realktek PCIe GBE Family Controller Series V.2.29 (06/30/09) PXE-E61: Media test failure, check cable PXE-M0F: Exiting PXE ROM Operating System not found Also, pressing f8 gives me the same results as booting as normal. It is running Windows 7 Ultimate, dual-core Intel i3 @ 2.27ghz and 4gb RAM. I think there is an issue with the HDD, as the "Operating System not found" would lead me to believe. Is this a fixable problem?

    Read the article

  • Are SATA II and SATA 3.0 Gbps compatible?

    - by Johnny Maelstrom
    I am trying to check that if I buy a new internal HDD it will work in the NAS I am buying. Currently I'm confused about naming schemes and once that is resolved whether there is compatibility. I will gladly author this question to be more general if there is not already an article helping with the confusion of SATA naming and standards. I see similar, but not identical questions and will accept this as a duplicate if thought as such. The specifications on the eCommerce site for the NAS says, "Controller Interface Type Serial ATA-150", the product home page for the manufacturer says, "Compatible with SATA and SATA II HDD". The specifications on the eCommerce site for the hard drives say, "Interface Type Serial ATA-300", the product home page for the manufacturer says, "Interface SATA 3.0 Gbps" Wikipedia says many things about different naming conventions, the closest being, "SATA II 3.0 Gbit/s, which was colloquially referred to as "SATA 3G" [bps] or "SATA 300" [MB/s] since 1.5 Gbit/s SATA I and 1.5 Gbit/s SATA II were referred to as both "SATA 1.5G" [b/s] or "SATA 150" [MB/s]). Therefore, they will operate with negligible differences between them." Are SATA II and SATA 3.0 Gbps the same? I feel I'm tantalisingly close to getting a definitive answer here before I purchase, but really want to clear up these naming schemes.

    Read the article

  • I need help choosing between two configurations of the Dell Studio 14

    - by Adnan
    There are two configurations of the Dell Studio 14 (1458) which I'm looking at: Config 1: Core i7-720QM @ 1.6 GHz; ATI Mobility Radeon HD 5450 1GB; 4gb DDR3 RAM @ 1066 MHz; 500 GB SATA HDD @ 7200 RPM; Price: $999 Config 2: Core i5-430M; ATI Mobility Radeon HD 4530 512MB; 4GB DDR3 RAM @ 1066 MHz; 500 GV SATA HDD @ 7200 RPM; Price: $874 What I want to know is, would config 1 still be able to do decent gaming (maybe some Starcraft II), and is there a great performance difference between the i5 and i7 processors? Is the $130 extra worth it for the i7 and better graphics card? I do more than just basic computing. I plan on getting into web design (specifically using Photoshop and Dreamweaver), and I wish to do gaming. I know Conifg 1 is the better value, but I want to be sure that the $130 more is truly worth it. I dont have too much money and want to spend wisely as possible, yet I am a computer geek and plan on doing a lot more than the average user.

    Read the article

  • How to find out which program a default beep is coming from in Windows 7?

    - by leeand00
    There's a "default beep" (as defined in System Sounds) that emanates from my computer every so often. It kind of goes like this (where each number is a "default beep" sound): 1, 2, 3, 4, 5. So there's a distinct pattern to it. I thought I had this figured out a way to figure out what was happening by going to Control Panel-Ease of Access-Ease of Access Center-Replace sounds with visual cues But that just isn't the case. Whichever window I click on, that one displays the visual queue when this happens. It's driving me crazy, and I can't figure out which program is causing this. Update: it appears to only happen on one user profile on the computer...does that help? Update 2: Discovered that this sound was coming from a utility on my laptop called ASUS NB Probe; I'm certain that it is emanating from this program because the error message displayed by it changes in sync with the sound playing. Apparently the S.M.A.R.T. feature of my hard drive was reporting an issue. It displays the issue for a brief second and then makes it disappear, I'll have to keep watching it to see what it says, but I believe is says something about a read. I have an external hdd connected with eSATA to a container of sorts (BlacX) that you can plug two hdds into. I have one hdd attached and it's a Western Digital WD1001FALS - 00E8B0 Thanks again! Now I'm off to go around the Internet and report on this...since I posted it so many places!

    Read the article

  • ASUS M51SE freezes for no apparent reason

    - by Piotr Justyna
    First of all, it's my first question on superuser so please excuse me if it doesn't belong here, a similar one has already been posted here or if I missed some details. My ASUS M51 freezes up. It all started a couple of months ago and I basically forgot about it since I bought a new laptop around that time. This is, however, bugging me since then and I can't explain why it's happening. Let me quickly describe what's wrong. When switched on and running (win 7) it freezes after a couple of minutes of normal usage (or even if I don't actually do anything). By 'freezes', I mean it's like a static image of my desktop was being displayed on the screen. Nothing happens, alt+ctrl+del doesn't help, I basically have to switch it off using a power button. I tried to remove the hard drive and to start the laptop without it. The same here - it freezes on the the initial black loading screen (a couple of minutes after the computer says it can't find the hdd) I tried to remove RAM - the same thing. All fans are spinning as they should. I cleaned the fans using a small paintbrush but it doesn't change anything. The laptop is generally clean and in pretty good physical shape. Well, almost, obviously :). One possible clue I can think of is that the laptop is heating excessively even when it doesn't actually do anything (hdd removed). Do you have any ideas what is the cause of this or what else can I try? Thanks, Piotr

    Read the article

  • No OS will boot, all freeze

    - by Gyan
    This is for a computer with the following configuration: Asus P5KPL-AM/PS motherboard Pentium D 820 (dual core 2.8 GHz) 1 x 2 GB DDR2-800 Transcend RAM 1 SATA2 Samsung 160 GB HDD 1 PATA LG CD/DVD Writer PS/2 generic Keyboard USB Razer mouse The computer was working fine till a month ago with a Hitachi HDD in place of the Samsung. But that drive died and I sent it in for warranty replacement. Since then and till last week, the computer had not been turned on. I then got hold of a spare but XPSP2-loaded Samsung drive from another computer and decided to get this computer temporarily running. However, when I tried to boot into XP, it didn't load. It got stuck at the first graphical screen. When trying Safe Mode, the file list would be updated up to diskio.sys and then freeze. If I tried to boot Kubuntu off a CD, I would get past the first menu, but then get stuck at the subsequent graphical interface in the loading process. A similar thing happend with a friend's Windows XP-on-a-pen-drive. I switched the RAM into the other slot, but no luck. Then I booted the Ultimate Boot CD and ran Memtest86+ and a couple of the bundled CPU stress tests but these detected no errors. Some searching on the Internet brought up the notion of the CPU failing to switch from "real" to "protected mode". I'm hoping to get a fix on what the problem is and what I can do about it. Edit: I've flashed to the latest BIOS, but that doesn't help. Also, Knoppix LiveCD also freezes. I notice that the LED in my mouse goes off at the time of freeze, but trying to boot without the mouse connected produces the same result.

    Read the article

  • Improving IO with FlashCache

    - by Devator
    I have a server with 2 HDD's (2x 1 TB), running in RAID 1 (SW-RAID). I want to improve IO performance by using flashcache. There are running KVM virtual machines on it, using LVM. Regarding this, I have the following questions: Will this even work? flashcache works for block devices, however these are all virtual machines with their own setup. How much would I expect to increase performance? Most virtual machines run websites and some host games. How big does the SSD needs to be? Would having a bigger SSD increase performance since it's able to cache more files? What happens if the SSD dies? Would flashcache retrieve files from the traditional HDD and I could simply replace the SSD? How much faster would writeback be in comparison with writethrough and writearound? I have no access to a test system unfortunately, so could I install flashcache on a live server without unmounting the the disks? I found a great tutorial here which I would be using.

    Read the article

  • Debian software raid 1: boot from both disk

    - by bsreekanth
    I newly installed debian squeeze with software raid.The way I did was, as also given in this thread. I have 2 HDD with 500 GB each. For each of them, I created 3 partitions (/boot, / and swap) I selected the hard drive and created a new partition table I created a new partition that was 1GB. I then specified to use the partition as a Physical Volume for RAID. and used for /boot and enabled bootable. Created another partition, which is of 480 GB, and then specified to use the partition as a Physical Volume for RAID. and used for /. Created another partion and used for swap Then RAID configuration: Through Configure RAID menu - create MD device - (2 for the number of drives, 0 for spare devices) Next select the partitions you want to be members of /dev/MD0. I selected /dev/sda1 and /dev/sdb1 (for /boot) Next select the partitions you want to be members of /dev/MD1. I selected /dev/sda6 and /dev/sdb6 (for /) And no RAID for swap partitions 'Finish Partitioning and write changes to disk' -- Finish the rest of the install like normal Everything is ok now, except I am not sure how to test my raid config. When I pull the power of the HDD, it only boots from one disk. I read in some forum that I may have to install GRUB manually on the other. In Debian Squeeze, there is no grub command. Not sure how to make my software raid bootable from both disk. Also, please comment on my steps above. Anything unusual. I configured /boot partitions of both disks to be boot=yes. Not sure whether that is ok. Thanks, Bsr

    Read the article

  • Windows 8: Clean Install Fails BEFORE country Screen

    - by Mark
    G'day, I've been trying to (clean) install Windows 8 on my PC now for over two weeks now, and it's really getting old. You can see here that I've outlined my issue to the Windows Technical Community, which has resulted in... absolutely no help at all. http://answers.microsoft.com/en-us/windows/forum/windows_8-windows_install/windows-8-clean-install-fails-before-country/64229d0a-0220-45a9-bdc6-c41062df8a75 Tl;dr? Yeah, me too. Basically, I've shrunk the HDD, it's working (I'm on that PC on XP). I've put both the x64 and the x86 DVD's, AND an another HDD with W8 installed on it from my test machine, and they ALL Fail to load. (I get the slanty windows logo, and after about 10 seconds BOOM. Sad face error screen.) I really don't want to have to remove the video card, or the unevenly/not partnered DIMM in the 2nd Memory channel - because the case is .. stupid, and in an awkward spot, but I'm running out of ideas! PS. I tried turning on ACHI tonight. All that resulted in was XP wigging out about new drivers & explorer.exe crashing. Fun times! :(

    Read the article

  • Force spin-down of external hard-drive on linux (raspberry pi)

    - by user258346
    I'm currently setting up a home-server using a Raspberry Pi with an external hard-disk connected via usb. However, my hard-drive will never spin down when being idle. I tried already the hints provided at raspberrypi.org ... without any success. 1.) sudo hdparm -S5 /dev/sda returns /dev/sda: setting standby to 5 (25 seconds) SG_IO: bad/missing sense data, sb[]: 70 00 04 00 00 00 00 0a 00 00 00 00 44 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 2.) sudo hdparm -y /dev/sda returns /dev/sda: issuing standby command SG_IO: bad/missing sense data, sb[]: 70 00 04 00 00 00 00 0a 00 00 00 00 44 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ...and 3.) sudo sdparm --flexible --command=stop /dev/sda returns /dev/sda: HDD 1234 ... without spin-down of the drive. I use the following hardware: Inateck FDU3C-2 dual Ports USB 3.0 HDD docking station Western Digital WD10EZRX Green 1TB Is it possible, that the sent spin-down-signals are somewhere overwritten/lost/ignored?

    Read the article

  • EFI vs MBR - Installing Windows Server 2008 R2 or 2012 on 8TB

    - by Riaan de Lange
    I'm having some difficulty installing Windows Server 2008 R2 and Windows Server 2012 on an Intel Server platform. The server specs is as follows: Intel Grizzly Pass Server System - R2308GZ4GC 2x Intel Xeon 2620 - 2.0 GHZ - BX80621E52620 132 GB of Memory REG-DIMM - TS1GKR72V6H 4x Seagate Constellation ES 2TB 3.5" 7200rpm 6GB/S - ST32000645NS Intel Big Laurel 4CH 6G SAS RAID 512MB - RS2BL040 On the Intel RAID Controller Setup, I have setup the HDD to be in RAID-0 - for testing purposes. (Ultimately configured in RAID-5) So, the total size of HDD space I can use is 7.6 TB something... When I install the Server OS's, they don't seem to go beyond 2 TB (1.76 TB) I have read up on EFI and UEFI boot, and this seems to work in 2012, but I could not install any drivers for the motherboard... So, I also tried EFI for 2008R2, and this worked while installing the OS, it did not however work with the Windows Boot Manager option in the BIOS. It kept on freezing once it tries to load the partition. My idea was to allocate the complete 8 TB for the OS, and load a few VM's on there. I have now started with a new approach where I'll have a 256 GB OS Partition, and a secondary 7.5 TB Data partition. Oh, and I also did a diskpart - convert disk to gpt whilst installing 2008R2. The whole disk was accessible, 7.6TB Can anyone please clarify that EFI/UEFI is meant for larger boot volumes? Bigger than 2TB. If I were to have an ideal situation where my OS is run on a SSD, 256GB, and I can attach the 8 TB drives as normal disk to the OS? I'm I correct in saying that if I wanted to boot from a 8TB partition, I would need to force the BIOS to boot from EFI? The limit for MBR is 2 TB as far as I know now... *FYI: The motherboard is EFI-ready

    Read the article

  • Updating a backup image (.wim and/or Acronis .tib)

    - by Backdraft
    Anyways, I've got a Windows 7 installation that I want to make a generalized backup image of so I can use it for future installs on not only my desktop from which the image is to be derived from, but also other systems with dissimilar hardware. Therefore I've arrived at either 2 options, using either sysprep/imagx from WAIK (guide here), or the simpler Acronis True Image w/ their Universal Restore addon. Of course, they create distinct image file types, .wim and .tib respectively. What I'd like to do is to periodically update this image, say with Windows Updates, by booting it to either a physical partition or using virtualization (VirtualBox/VMWare), perform the updates, and save the updated .wim or .tib image file again. What's the simplest way I could do this? Another question is, I created this generalized backup image on a 500GB Seagate 7200RPM HDD. Say I get an SSD as an OS drive in the future, can I just deploy this backup image to the SSD normally, or are there any potential problems to be aware/avoid (ie. is it best to completely reinstall the OS on the SSD from scratch, or can I use the image created on the normal HDD with no issue)? Thanks and Happy Holidays.

    Read the article

  • What is the fastest way to resize a large partition?

    - by Jook
    Due to a new HDD-Configuration I am currently handling larger backup/resize tasks with partitions between around 900MB, wich are 70-90% full. some background: First thing I've noticed was, that the Acronis-WesternDigital TrueImage was extremly slow while running it under Windows 7, even though on high priority. To create a normal backup for 650gb of data (900gb partition), it would have taken 3 days! The same task done with the boot-cd version of this acronis version took about 2 hours (SATA3 copy from one disk to another, both around 110MB/s). Now, after I have done all my backups, I've wanted to remove some obsolete partitions and resize the leftovers to full hdd size. Of course, usually this takes quite some time - in this case for this 900gb partition, to extend it to 931 (30gb+ from front, 1gb+ from end), it will take around 6 hours (using gparted)! Had I new that erlier, I would have just restored the image. But no - first it showed a reasonable time of 1:45h and 0 of 1 operations, but after finishing 1:45h it started again, only this time with 4h to go, still 0 of 1 operations, but now it was copying instead of moving. Question: However, why has it to be this slow to resize a partition? I am asking for a good explanaition. This has bugged me, since I started partitioning - why does it require to copy all the data around, can't it just stay in place?!

    Read the article

  • How do I repair a Windows 7 installation damaged by Windows 8 sleep mode

    - by Mat
    I'm experimenting with a Windows 8 installation which is on a separate SSD. My actual Windows 7 installation I'm working with is on my old HDD. While Windows 8 was in sleep mode I swapped the hard disks and put in the Windows 7 HDD (I thought the computer was off). When I started the computer, Windows 8 started back up to the login screen – then it was stuck and some seconds later the computer rebooted. Now the Windows 7 Installation is damaged. When I boot, after the Windows 7 startup logo appears, a bluescreen shows up for few seconds stating: STOP: c000021a {Fatal System Error} The verification of KnownDLL failed. System process terminated unexpectedly with a status of 0xc000012f (0x00f0bb90 0x00000000). The system has been shut down. and then the computer reboots. The same happens in safe mode. 'Windows startup repair' cannot repair the issue. Any idea what could have happened exactly and/or how to repair this Windows 7 Installation?

    Read the article

  • PC powers off at random times

    - by Timo Huovinen
    Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

    Read the article

  • prevalent, recurring hardrive failure intel macbook from 2006/2007

    - by SimonSalman
    Hi, Long story: My MacBook's hard drive failed one year ago, just a month after its warranty ended or: a year and a month after I bought it. After about ten phone calls to Apple's service, they agreed to extend the warranty for another year, so that I got it replaced free of charge. In the mean time, I got to know that many MacBook users that experience/report hard drive failures. Every reported crash was preceded by a slowdown of system performance, an increased occurrence of the spinning beach ball wait courser, and frequent crashes of applications that used to run very robust until then. It happened (as far as I know) with MacBooks from 2006/2007. All these MacBooks additionally suffer from a recurring wearing down of their "top case". Many heavy users had to replace their HDDs three time since 2006/2007 resulting in an head crash, making it impossible to recover data (diagnosis of recovery specialists) in most but not all cases HDD was Seagate (doesn't necessarily have to be the cause, if majority of the MacBook charge contained Seagate drives) And right now (one year after my first disk crash), these symptoms are cumulating on my system, again ... Short version: prevalent hard drive failure on MacBook charge from 2006/2007 (i.e. 2.16 GHz Intel Core 2 Due) I am looking for any (preferable open source) tool for checking the hard drive condition, especially to detect the known "MacBook problem". So, that I can replace the disk on time. If any Mac user found a solution to prevent the repeated failure of heir hard drive, I would be very glad to get to known it. I really enjoy my old MacBook, but I hate to get interrupted every year by an HDD crash. BTW, the issue is already in discussion for a long time, but there seems to be no solution, so far. Thanks, Simon

    Read the article

  • Hosting websites in our Workplace custom-built datacentre

    - by i.h4d35
    I'm faced with unique learning opportunity at work at the moment. Due to the slowdown (amongst other reasons), the powers that be at my office have decided to abandon our shared hosting providers (both shared and dedicated hosting) and have decided to host the websites at our office's datacentre. We're running 7 websites, wherein the average unique hits per day at the moment is about 900. We have 2 servers set aside for this - one is a DELL POWER EDGE 1850 (Intel Xeon 3 GHZ*2, 4GB RAM, 73GB HDD and the other is an HP DL 380 G3 (Intel Xeon 2.8 GHz, 6 GB RAM, 73 GB HDD) a) I would like to know the pros and cons of going ahead with this project.All the sites will be hosted on a single IP. In all probability, the OS is going to be CentOS. b) Do you think I should consider Virtualization into this equation (KVM/Xen)? I was thinking in terms of separate instances of the DB server and the frontend though I do not know if this is the best way to go. c) Should I be trying to use cloud stacks like OpenStack and try to make it look like websites hosted on some sort of Public Cloud? (something that I checked out here). Here is something else I came across, which looks similar to what needs to be done at our office. About the websites - Of the 7 websites, 4 are basic static websites which basically gives a whole lot of information about a few local institutions. The remaining 3 are local product-based websites developed in PHP wherein end user can view products and order them online. I am trying to take this as a learning experience wherein I can learn to build something from scratch and save the company a little something in the process. The migration needs to be completed by Easter so I guess it gives us some time (or am I being overly optimistic??). I am confused here and would appreciate all the help I can get. Thanks in advance.

    Read the article

  • Installing Windows 7 from USB on a Thinkpad T61

    - by Halik
    I am trying to install Windows 7 Professional from USB 3.0 flashdrive, on a Thinkpad T61. The problem is, Thinkpads BIOS will not detect the flash drive as bootable medium, and won't allow to boot from it. What I did: Enabled USB BIOS Support in BIOS (it was on by default) In startup menu, added USB HDD to boot order (it has '-' sign in front of it) Created Windows 7 install media with UNetbootin, WinUSB (linux tool) dd and Grub4DOS. As you can tell, currently, I only have access to Linux machine to make the flashdrive. What happens: The T61 BIOS shows '-USB HDD' in boot order menu. The '-' sign suggests that the plugged flash drive is currently not bootable. The same flashdrive (with the same Windows image on it) is booting without any problems on a Dell D430 and Lenovo Y550. Also, Ubuntu 12.04 install USB created with Unetbootin shows as bootable ('+' sign in BIOS boot order menu) and boots from the F12 boot menu. Additional info thinkwiki.org says that some Thinkpad BIOSes do not use MBR on flashdrives. It suggests using Extended-IPL boot loader, but the provided links are broken and there seems to be no mirrors. Solution: http://superuser.com/a/430186/54970

    Read the article

  • SSD causing 100% CPU usage in Apache/PHP

    - by Tim Reynolds
    I wanted to increase the performance on my development laptop so I added an Intel 320 Series SSD as my primary drive. Everything is amazingly fast, as expected, except Apache/PHP. I develop Magento by using an Ubuntu 10.10 virtual machine. Information: Host OS: Win 7 Professional 64bit Guest OS: Ubuntu 10.10 32bit Processor: i7 Chipset QM55 SSD: Intel 320 Series 160gb 30% full HDD: Hitachi 320gb 50% full (in side bay using an adapter) Laptop: Lenovo T510 Using: Shared folders Apache Version: 2.2.16 PHP Version: 5.3.3-1 APC Version: 3.1.3p1 APC Memory: 128M Using tmpfs for cache, log, session directories in Magento In the VM running on the SSD (VM files and source files are on the same drive) loading a product page in the Admin takes on average 26.2 seconds and uses 100% CPU for nearly the entire time. In the VM running on the old HDD loading the same page takes on average 4.4 seconds. It mostly uses around 40-50% of the CPU while rendering the page. I have read this post: Performance issues when using SSD for a developer notebook (WAMP/LAMP stack)? It says to change some settings in the bios. I have turned any and all power management features off in the bios. I can't for the life of me understand why this would be happening.

    Read the article

  • Migrating away from LVM

    - by Kye
    I have an Ubuntu home media server setup with 4.5TB split across a few hard-drives (1x3TB, 2x1TB) and I'm using LVM2 to manage the volumes. I have recently added a 60GB SSD to my server, and I wish to use it to house the 'root' partition of my server (which is currently under the LVM group). I don't want to simply add it to the LVM volume group, because (afaik) there's no way to ensure that the SSD will be used for the root filesystem. If I just throw it at the VG, it may be used to house my media, which would defeat the purpose of having the SSD in the first place. I feel that my only solution is to somehow remove my root partition from the LVM setup and copy it across to the SSD. My boot partition is, of course, not part of the LVM group. My disk setup is as follows: 60GB SSD: EMPTY. 1TB HDD: /boot, LVM space. 1TB HDD: LVM space. 3TB HHD: LVM space. I have a few logical volumes. my root (/), a 'media' volume for my media collection, a backup one for my network backups.etc. Does anyone have any advice as to how to go about this? My end goal is to have the 60GB SSD used for my boot and root partitions, with everything else on the 3TB/1TB/1TB hard-drives.

    Read the article

  • Disaster recovery backup of files/photos for personal use

    - by Renesis
    I'm looking for the best method to store a backup of important files and 5+ years of digital photos that is safe from some type of fire/flood disaster in my home. I'm looking for: Affordable: Less than $100/yr or first-time cost. Reliable: At least a smaller chance of failing than there is of fire or flood Easy for initial backup and to add to, and at least semi-easy to recover. I recently purchased a small home safe for physical vitals. It was inexpensive, solid, and is fire/water safe. If I had a physical copy of the digital files, the safe would work fine for this, but I don't know what to store in it that adequately meets the requirements above. Hard drive - I read that the danger of it not spinning up makes a hard drive a bad choice for this type of storage, although it was my first thought and would definitely be the simplest choice - very easy to take out once a month and add files to. DVDs - Way too much of a hassle for both backup and restore. Tape - No idea on the affordability of this option Online - Given that I have at least 300GB already and ever-increasing megapixels means ever-bigger files, and my ISP upload is about 2Mb at the best, this just doesn't sound like a good option for me, but I could be convinced. Other - Have I missed something? Also, I'm already covered both for sync between computers (Dropbox) and a nightly backup of these files (External HDD). The problem with the nightly backup is obviously that it's always with the computer and in a disaster would be destroyed along with it. Is anyone else doing something similar? Is the HDD as poor of a choice as I read, or is it a feasible option? Maybe two to reduce the likelihood of failure?

    Read the article

  • Window 7 Computer name changing on its own?

    - by DC
    Very odd problem... I have a Dell Latitude D830 with XP Pro that has been running on my local domain for many years. I recently Installed Windows 7 Enterprise on the D830 using a brand new HDD so that I could still use XP if I needed by just swapping out the HDD's. I added the W7 installed system to my domain using a completely different machine name than that used for the XP system and everything seemed to be functioning as it should. On boot up over the last 2 weeks or so I occasionally (3 times now) get to the login screen and try to login to the domain only to get an error saying that the Computer name is not a trusted machine in the domain I'm trying to log in to. Come to find out that the machine name on the W7 system has been changed somehow to that of my old XP system. If on the W7 system I then change the name back to the correct name, disjoin the domain, reboot, add the machine back into the domain … all is well for an unknown period of time until this happens again. This last time, I know for a fact that everything was fine the day before when I shut down the system. I came in today, powered up the system and the machine name had been changed to that of my old XP system again. Has anybody else seen this behavior or hav any ideas on what could be causing it? Thanks!

    Read the article

  • Can Current Backflow from Powered Hub's Adapter & cause PC Damage?

    - by SuperUserMan
    Getting this short: Can current flow from a powered USB hub's power adapter (lying 10 Meter away) back to computer via usb port and cause damage to Computer components like mobo, etc? What should be my concerns? Using a 2 Amp 5V Power adapter to power a 10m Long Active Repeater USB extension cable with 4 port HUB & plugging into PC's Front port, causes PC Chassis fan to keep running (thought slower than regular speed) Front Chassis HDD & power LED to turn on (though bit dim) may be other things which i cant detect/see at chip level, in motherboard?? All this even after PC is shut down (bit scary) More detail (in case still want to read): To run 4 High power (needing 450 mAmps) Wifi Adapters, far away from PC, Bought Active Repeater USB Extension Cable with 4 Ports & power port at far end http://www.ebay.com/itm/33FT-USB-2-0-Male-to-Female-Extension-Cable-Hub-Splitter-Adapter-with-4-USB-Port-/390846115254 Then added a locally bought 2 Amp 240V AC to 5V DC Power Adapter and plugged into USB hub which is a part of & situated at far end of a 10 Meter Active Repeater usb extension cable. Even 4 Wifi Adapters run fine (appear to) using this setup, but running chassis fan, dimly lighted Power & HDD LED, even when PC is switched off is bit scary and surely mean 5V & some current is flowing all though that 10 meter extension cable into my USB port & powering stuff. Can this cause damage? and what should be my concerns. Of course I can't switch off the power adapter (lying 10 meters away from PC) every time I switch off my PC to prevent this.

    Read the article

  • Windows 7 Won't Boot

    - by Vie
    I recently built a new computer, my fifth one. ASUS Maximus III Formula LGA 1156 Intel P55 ATX Motherboard EVGA 01G-P3-1452-TR GeForce GTS 450 Superclocked 1GB 128-bit GDDR5 PCI Express 2.0 x16 HDCP Video Card COOLMAX RM-1000B 1000W ATX psu Intel Core i7-875K lynnfield 2.93GHz LGA 1156 95w Quad-Core unlocked processor G.SKILL Ripjaws Series 16 (4x4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10666) memory WD VelociRaptor WD3000GLFS 300gb 10000 RPM SATA 3.0Gb/s Hard Drive Sony Optiarc CD/DVD Burner model AD-7261S-0B LightScribe Windows 7 Home Premium 64-bit It gets hung up on the starting windows screen. When I went to install the OS it did the same thing wouldn't go past the windows logo, so I put the new HDD into my old computer and installed windows 7 thinking it was just an installer error. Put the fully installed HDD back into my new machine and it still gets stuck on the starting windows screen. I've tried most everything I've looked up. Disabled USB, Disabled Turbo Boost, Disabled everything that wasn't essential(just about every configuration I can think of), took it apart and put it back together, took all the ram out save one 4g stick(wouldn't even boot when I did this), did a memory scan which came back successful, I don't know what could be wrong. Only thing I can think of is a compatibility issue somewhere, but I've ran over it again and again and I don't know where there would be an issue like that. Need Backup! .<

    Read the article

  • New SSD, is the MBR broken? DISK BOOT FAILURE

    - by Shevek
    I've been running Windows 7 on a WD 500gb SATA single drive, single partition setup for some time with no issues. I've just installed a new Kingston V Series 64gb SSD and performed a clean install of Win7 to it, deleting the partitions on the 500gb and using that as a data drive. All was well for a few reboots but then I started to get "DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER" messages. If I put the Win7 install DVD back in the drive it boots fine. Tried a clean install again, after replacing SATA cables and swapping SATA ports, with a complete partition wipe of both drives. Again, rebooted fine a few times then back with the "DISK BOOT FAILURE" error. Looked on the web and found some discussions about it so I then started from scratch again. This time I wiped the MBR on both drives using MBRWork, disconnected the 500gb and reinstalled to the SSD. Removed the install DVD and installed all the drivers which involved many reboots, all with no problem. To make sure I also did a few cold boots as well. Reconnected the 500gb, initialised, partitioned and formatted it. Copied data to it and did some more reboots and shutdowns. All was ok. Then out of the blue comes another "DISK BOOT FAILURE" and again, if the Win7 install DVD is in the drive it boots fine. So, is the SSD a bad'un? TIA UPDATE: It was a BIOS issue! I found a hidden away option for HDD boot order, which was separate from the usual HDD/CDRom/FDD boot order option. The WD was set to boot before the SSD... Swapped them round and all is well. Still don't understand how it worked at first though... Thanks Solaris

    Read the article

< Previous Page | 41 42 43 44 45 46 47 48 49 50 51 52  | Next Page >