Search Results

Search found 87901 results on 3517 pages for 'exchange server'.

Page 452/3517 | < Previous Page | 448 449 450 451 452 453 454 455 456 457 458 459  | Next Page >

• How do I setup JBoss 5.1.0.GA to run multiple instances?

  - by djangofan

  Does anyone have any experience or advice in setting up multiple JBoss 5.1.x instances on the same machine that has 1 network card? Here is what I did: Installed JBoss 5.1.0.GA into c:\myjboss 1.5. I copied the server/default directory to server/ports-01 and server/ports-02 so they have their own config. did I assume correctly? Ran .\run.bat -c ports-01 Ran .\run.bat -c ports-02 At this point there are 2 instances but the second instance doesn't load correctly because of what is probably a few port conflicts. For example: the http port ends up being 8080 for both instances, which it gets from line #49 in the C:\myjboss\server\all\conf\bindingservice.beans\META-INF\bindings-jboss-beans.xml file. Earlier in the server load it clearly gets the value from line#63 in that same file. I don't know why it gets part of the port config from line #49 and the other part from line#63. Confused. I also tried: .\run.bat -Djboss.service.binding.set=ports-01 -c ports-01 and it made little difference. Any ideas on what I am doing wrong?

  Read the article

• Site hanging in iis7 - how do I troubleshoot?

  - by Chris Foot

  I am currently having a problem with a windows 2008 server running IIS 7. The server runs several sites but only seems to have the issue with one particular site. Every so often, the whole server slows to a crawl with nearly all requests timing out! Invariably, when we log in to take a look there is always an IIS process using up around 90% cpu. Looking into the worker processes in IIS there are usually one or two requests that have been running for a long time. They are always in the ExecuteRequestHandler state with ManagedPipeline as the module name and the current ones i'm looking at have been running for 7686248 (what units is this in, it doesn't say?). It is also not always the same page, in fact we have seen at least 3 different pages listed under url when this has happened. It seems that the only way to bring the server back to life is to kill the 90% process! The site is running under .Net 4.0 and the code on it is very similar to other sites on the server which do not have the problem! How do I start troubleshooting this?

  Read the article

• Cygwin's RSYNC for large data transfer

  - by Tim Brigham

  I'm using rsync from Cygwin to do a large scale data transfer from an aging HP MSA 1000 to a new DAS attached to a different server. I have a daemon running on the remote server in read only mode and a local copy writing the files to disk. One of my servers is an image repository with over a million files spread across about 300 directories. Each file averages only a couple hundred kilobytes. More so than any other box this one is proving problematic. The rsync process will work for a while - some times 20 minutes, some times an hour - and then it simply quits and sits idle at a given file name. I have verified that the file isn't corrupt on the remote server and that the file is successfully created on the local drive. I ran the rsync client in -vv mode, which returns nothing. I checked out the logs created by the daemon. I looked at the network utilization on the interface, which is sitting idle. I looked at the AV settings to see if anything could pose a problem there. I even updated to the latest release of Cygwin. What do I need to in order to keep this connection up? EDIT: The client system is using the command rsync.exe server::Drives/f/Repo/ /cygdrive/T/Repo --archive -P -vv The server is using the command rsync.exe --daemon --no-detach --config "rsyncd.conf" The contents of rsyncd.conf: use chroot = false strict modes = false hosts allow = 192.168.100.9 log file = c:/rsyncd.log uid=0 gid=0 [Drives] path = /cygdrive read only = yes EDIT: The file server is 2003, the disk type on the array is GPT and the size is of the array is about 4 TB. EDIT: Stranger.. It looks like the process is reliably erroring out at about 175,000 files. Rsync runs fine when I pick the same directory it has problems with one at a time. EDIT: rsync version 3.0.9 protocol version 30 Copyright (C) 1996-2011 by Andrew Tridgell, Wayne Davison, and others. Web site: http://rsync.samba.org/ Capabilities: 64-bit files, 64-bit inums, 32-bit timestamps, 64-bit long ints, no socketpairs, hardlinks, symlinks, IPv6, batchfiles, inplace, append, ACLs, xattrs, iconv, symtimes A similar failure occurred when going from the same set of files with Cygwin to a Linux install. It didn't happen until several hours later than normal however.

  Read the article

• DHCP for Multiple Subnets

  - by TheD

  So this is the current setup - essentially I would like to get my DHCP server, serving DHCP requests for two seperate subnets. Netgear DG834G acting as a modem connected to a Sonicwall Pro 2040. X0 - LAN - 192.168.1.0/24 X1 - WAN - <WAN-IP> X2 - WLAN - 192.168.10.0/24 At the moment, I have a 2008R2 server with DHCP installed, with an IP address on the 192.168.1.0/24 range handling DHCP fine for this subnet. The Sonicwall is configured correctly - anything connected to the WLAN has Full Allow to anything in the LAN, and vice versa but it will not lease an IP from my Server. I've also added another IP address to the server, so the physical NIC now has two IP's: 192.168.1.2 and 192.168.10.2 with a DHCP scope configured for each. Still no luck! Any ideas? Thanks!

  Read the article

• How to bypass vpn talking to VMWare Guest?

  - by marc esher

  Greetings. Network/VPN n00b question here. I'm running VMWare Workstation with a Guest Windows 2003 Server. It has SQL Server 2000 installed. The sole purpose for this Guest is to house SQL Server... it needn't have internet access or access to any other resources on the network other than the host. When launch Check Point VPN software, the host routes through the company network before it connects to the guest ... i.e. it's no longer a direct connection. I assume this is just how things are supposed to work. However, what's happening is that the connection between my host and the SQL Server instance on the guest intermittently drops. It's not consistent, and some databases on the server will be responsive while others aren't. It appears that the databases with the most traffic on the guest (the ones I'm hitting with load tests) are the ones that become intermittently unresponsive. This problem only manifests when VPN is on; when it's off, I can pound away on this database with no troubles. Thanks for any advice!

  Read the article

• OpenVPN bridged not pinging beyond openvpn server on Ubuntu/Windows 2003

  - by ani

  I set up an OpenVPN server using Ubuntu and a windows server 2003 client to interconnect two networks between two different offices. They can now ping each other, but the rest of the network cannot be contacted by the windows client. Office 1 has internal network of: 192.168.0.0 255.255.240.0 Office 2 has internal network of: 192.168.16.0 255.255.255.0 And the configuration files are: Server.conf port 1194 --script-security 2 up "/etc/openvpn/up.sh br0" down "/etc/openvpn/down.sh br0" # TCP or UDP server? ;proto tcp proto udp dev tap0 ;dev tun ca ca.crt cert openvpn.crt key openvpn.key dh dh1024.pem ifconfig-pool-persist ipp.txt server-bridge 192.168.0.59 255.255.240.0 192.168.6.72 192.168.6.75 push "route 192.168.0.0 255.255.240.0" push "dhcp-option DNS 192.168.0.2" push "dhcp-option DOMAIN testeers.local" keepalive 10 120 tls-auth ta.key 0 # This file is secret comp-lzo user nobody group nogroup persist-key persist-tun log /var/log/openvpn/openvpn.log status /var/log/openvpn-status.log verb 3 Client Config file client dev tap ;dev tun --script-security 2 ;proto tcp proto udp remote 1xx.2xx.xxx.124 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert admin-VAIO.crt key admin-VAIO.key ns-cert-type server tls-auth ta.key 1 comp-lzo verb 3 Ifconfig on the server now shows the following: br0 Link encap:Ethernet HWaddr 00:50:56:8b:1a:49 inet addr:192.168.0.59 Bcast:192.168.15.255 Mask:255.255.240.0 inet6 addr: fe80::250:56ff:fe8b:1a49/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1081860 errors:0 dropped:1358 overruns:0 frame:0 TX packets:242385 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:76600615 (76.6 MB) TX bytes:64474575 (64.4 MB) eth0 Link encap:Ethernet HWaddr 00:50:56:8b:1a:49 UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:1144125 errors:0 dropped:7172 overruns:0 frame:0 TX packets:252486 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:109893729 (109.8 MB) TX bytes:66372620 (66.3 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:67865 errors:0 dropped:0 overruns:0 frame:0 TX packets:67865 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5183276 (5.1 MB) TX bytes:5183276 (5.1 MB) tap0 Link encap:Ethernet HWaddr 32:4f:42:11:b7:c5 inet6 addr: fe80::304f:42ff:fe11:b7c5/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:3329 errors:0 dropped:0 overruns:0 frame:0 TX packets:215472 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:373205 (373.2 KB) TX bytes:17465832 (17.4 MB)

  Read the article

• SMTP IP - Bad reputation, how do I work around?

  - by Louis van Tonder

  I recently had a spamming incident and got listed on a blacklist. I have rectified the issue, removed from the blacklist, but my IP reputation is now classified as a high volume sender. What is the best way to rectify this? I have an additional IP address. I am thinking configure my server to make outbound SMTP connections using the other IP. My questions are: How long does it take for my reputation to stabilize again? How do I configure my server/mailserver to use a specified outbound IP? Setup: Server 2008 Web hMailserver 2 IPs configured on one NIC Cloud based server Your urgent help would be greatly appreciated. Cheers

  Read the article

• Suggestions for splitting server roles amongst Hyper-V virtual servers / RAID6 or RAID10? / AppAssure

  - by Anon

  We have 2 Hyper-V hosts at present running 1 virtual server that was converted from a physical box running all roles. My plan is to split the roles over various virtual machines, upgrading to the latest software versions as I go, and use the backup server as a standby in case the main server fails. AppAssure backup software has a feature called Virtual Standby, so the VHD's can be ready to be fired up on the backup server if necessary. Off-site backups will be done via external USB drive for now. I'm just seeking some input/suggestions into how I'm planning to split the roles out amongst various virtual servers. Also, I'm curious how to setup the storage on the servers. We do not have any NAS's, SAN'S or any budget for this. What would the best RAID level be to use? I'm thinking either RAID6 (which is currently used) however I'm concerned about the write speeds, or RAID10 but again I'm worried that I can only lose 1 drive (from the same mirror) as opposed to any 2 with RAID6. I realise I have a hot swap for this, but what if a further drive fails during a rebuild? Is the write penalty of RAID6 worth the extra reliability over RAID10? Or will it be too slow with all the roles I am planning, therefore RAID10 is my only real option? The reason for the needed redundancy is I am the only technician and I'm not always on-site. Options I've considered: 1) 5 drives in RAID6 set, 200gb for host OS, rest for VM storage. 1 drive for hot swap - this is how it is currently setup 2) 4 drives in RAID10 set, 200gb for host OS, rest for VM storage. 2 drives for hot swap 3) 4 drives in RAID10 set for VM storage, 2 drives in RAID1 set for host OS. No drives for hot swap - While this is probably the best option with the amount of drives I have, I don't like the idea of having no hot swap 4) 3 drives in RAID6 set for VM storage, 2 drives in RAID1 set for host OS. 1 drive for hot swap All options give us enough storage capacity for our files, etc. We don't have any budget for extra drives or extra hot swap HD chassis for the servers. We have about 70 clients and about 150 users. MAIN SERVER Intel Xeon 5520 @ 2.27 GHz (2 processors) 16GB RAM 6 x 1TB Seagate Barracuda ES.2 Enterprise SATA drives Intel SRCSATAWB RAID controller Virtual machine workload using Hyper-V on Windows Server 2008 R2: DC01 - Active Directory Domain Controller / DNS server / Global catalog - 1GB RAM DC02 - Active Directory Domain Controller / DNS server / Global catalog - 1GB RAM Member Server - DHCP server, File server, Print server - 1GB RAM SCCM Member Server - 4GB RAM Third Party Software Member Server - A/V server, Ticketing software, etc - 4GB RAM Exchange 2007 - 4GB RAM - however we are probably migrating to a hosted solution, therefore freeing up resources BACKUP SERVER Intel Xeon E5410 @ 2.33GHz (2 processors) 16GB RAM 6 x 2TB WD RE4 SATA drives Intel SRCSASRB RAID controller Virtual machine workload using Hyper-V on Windows Server 2008 R2: AppAssure backup software - 8GB RAM

  Read the article

• What Windows licenses are required to run additional terminal service sessions

  - by John P

  We need to build out a server running Windows 2008 R2 Standard that can allow up to 10 simultaneous RDP/Terminal Services connections and I'm a little confused about how the CAL licenses work. From one source I was told I needed 10 "server CALs" and an additional 10 "RDP CALs" (total of 20 CALs). From another, I was told I just needed the 10 "RDP CALs", which implicitly came with the server CAL. The Microsoft licensing website (http://www.microsoft.com/windowsserver2008/en/us/licensing-rds.aspx) seems to support scenario #1, but it is still not real clear what those server CALs are needed for. Also, can we use the 2 "built-in" RDP clients, meaning we only need to purchase 8 CALs to reach a total of 10?

  Read the article

• How to use remote desktop on Ubuntu without a X logged in session?

  - by ycseattle

  I am able to use remote desktop on my Ubuntu server (with gnome desktop installed) when I also have an active session on the desktop. I would like to be able to remote desktop to this server after I just turn on the power (no screen and keyboard to the server), is that possible? Thanks!

  Read the article

• Route through site-to-site VPN not working

  - by Jonathan

  I'm trying to set up a site-to-site VPN using RRAS on two 2K8r2 servers since yesterday. The connection is working at this point, but I can't get it to send traffic from one site to the other one. Set up: the set up is the same on both sites: the server is connected to a router that's connected to a modem. The routers act like a DHCP-server and assign IP addresses from the range subnet.21-subnet-.100. Both servers use a static IP address, subnet.11, and are set up as DMZ. Configuration: the servers are configured using the wizard to set up a site-to-site connection. This works with a demand-dial interface and a PPTP VPN connection. As mentioned, the VPN connection work properly. Problem: I can't get the servers to send the traffic for the other site, to be sent through the VPN connection. I added a static route on both server (home, office 1) and I can see the result in the IP routing table (home, office 1). I did this because the route didn't show up automatically. My guess is that this last step isn't right, for example because the routing table states "non demand-dial", which seems not correct. Home: Subnet: 10.0.1.0/24 Router: 10.0.1.1 Server: 10.0.1.11 (DMZ) DHCP: 10.0.1.21-10.0.1.100 RRAS DHCP: 10.0.1.101-10.0.1.150 Office 1: Subnet: 10.0.2.0/24 Router: 10.0.2.1 Server: 10.0.2.11 (DMZ) DHCP: 10.0.2.21-10.0.2.100 RRAS DHCP: 10.0.2.101-10.0.2.150 I hope someone has an idea to get this route working!

  Read the article

• Is there any problem using the ftpd that comes with Kerberos on CentOS?

  - by Chen Levy

  Hello, I need to configure ftpd on a CentOS 5.3 host to allow anonymous ftp (upload and download) from a well defined directory. I wish the setup to be as simple as possible, and to introduce as little new dependencies as possible. Scanning the current server configuration, I found the ftpd server that comes as part of the Kerberos workstation: > rpm -ql krb5-workstation | grep ftpd$ /usr/kerberos/sbin/ftpd Is there any reason I could or should not use this ftp server?

  Read the article

• EventID 1058 Code 5, Sysvol is subdir of Sysvol - how to fix?

  - by nulliusinverba

  I have been trying to resolve this error, like many others: The processing of Group Policy failed. Windows attempted to read the file \domain.local\SysVol\domain.local\Policies{3EF90CE1-6908-44EC-A750-F0BA70548600}\gpt.ini from a domain controller and was not successful. Group Policy settings may not be applied until this event is resolved. This issue may be transient and could be caused by one or more of the following: a) Name Resolution/Network Connectivity to the current domain controller. b) File Replication Service Latency (a file created on another domain controller has not replicated to the current domain controller). c) The Distributed File System (DFS) client has been disabled. Error code: 5 = Access Denied. The incredibly helpful post is this one (http://www.experts-exchange.com/OS/Microsoft_Operating_Systems/Server/2003_Server/A_1073-Diagnosing-and-repairing-Events-1030-and-1058.html). Quoting from this post: HERE IS A LIST OF POTENTIAL PROBLEMS THAT CAN LEAD TO 1030 AND 1058 EVENT ERRORS: --Sometimes the permissions of the file folders that contain Group policies (the Sysvol folder) can be corrupted. --Sometimes you have problems with NetBIOS: --Sometimes the GPO itself is corrupt, or you have a partial set of data for that GPO. --Sometimes you may have problems with File Replication Services, which almost always indicates a problem with DNS --Sysvol may be a subfolder of itself: Sysvol/Sysvol I have the problem listed where sysvol is a subfolder of sysvol. The directory structure is: -sysvol -domain -staging -staging areas -sysvol (shared as "\\server\sysvol") -domain.local -ClientAgent -Policies -scripts Interestingly, the second sysvol folder is the one that is shared as "\server\sysvol". This makes me confident this is the issue with the permissions and error code 5. Also interestingly, my server 2008 R2 servers can see it fine - my server 2008 servers cannot, and get the error. This is consistent across all my servers. This latter fact makes me uncertain what I need to do to fix this up. Do I, e.g., simply move the shared sysvol folder up a level to replace the non-shared one? Any help greatly appreciated. Cheers, Tim.

  Read the article

• New SBS 2011 installation (not migration) in an existing 2008 R2 domain

  - by Tong Wang

  My current network setup has two servers: a Windows 2008 R2 with TMG 2010 as edge firewall (TMG server), a second 2008 R2 with DC, DNS and Hyper-V roles (DCDNS server). I was trying to install SBS 2011 as a child partition on DCDNS, first I installed SBS 2011 in English and did the migration successfully. However, later on, I found that I can't change the display language in SBS 2011 once it's installed (but the clients require a different language), so I had to re-install the SBS in a different language. It is during the re-installation that the problem came up: the migration can't be completed with some error message stating "can't access the source server". I re-ran the migration preparation tool, but it didn't make any difference. I wonder if it's because the source server can only be "migrated" once. Since I only need to setup a handful of users and computers, so I decided to do a new install of SBS and picked a different domain name. But I can't get the SBS to connect to LAN: it can't ping other servers, neither can other servers ping the SBS server. I've tried to stop the DC/DNS services on DCDNS and restart SBS, but with no difference. Anyone has idea how to fix this problem?

  Read the article

• Automatically restarting Perfmon Data Collector Sets

  - by Scott Herbert

  I have a number of User Defined Data Collector Sets running on a Windows 2008R2 server, collecting perfmon stats from various servers. Whenever there is a network interruption, or a server rebooted (at worst, when the server which is running all these DCSs is rebooted), I have to manually restart some or all of the Data Collector Sets. Is there a way to configure them to automatically restart, or otherwise be more resilient?

  Read the article

• rdate for Windows 2008

  - by Lars D

  I need a command line tool that adjusts the time of a Windows 2008 server, using an internet clock. The purpose is to adjust the time in a script, when other apps from that script are not running. It is not an option to use the built-in NTP service because that makes some apps on this server fail - note, that this server is used in an industrial environment with no PCs on the network and no Windows update or similar applied. Any idea, anyone?

  Read the article

• “NT AUTHORITY\ANONYMOUS LOGON” error in Windows 7 (ASP.NET & Web Service)

  - by Tony_Henrich

  I have an asp.net web app which works fine in Windows XP machine in a domain. I am porting it to a Windows 7 stand alone machine. The app uses a web service which makes a call to sql server. The web server (IIS 7.5) and SQL Server are on the same stand alone machine. I enabled Windows authentication for the website and web service. The web service uses a trusted connection connection string. The web service credentials uses System.Net.CredentialCache.DefaultCredentials. I noticed username, password and domainname are blank after the call! The webservice and web site use the 'Classic .NET AppPool' with NetworkServices identity. I am getting an exception "NT AUTHORITY\ANONYMOUS LOGON" in the database call in the web service. I am assuming it's related to the blank credentials. I am expecting ASPNET user to be the security token to the database. Why is this not happening? Did I miss a setting? (Usually this happens when sql server and web server are on two different machines in a domain, delegation & double hopping, but in my case everything is on a dev box)

  Read the article

• SQL 2008 R2 replication error: The process could not connect to Distributor

  - by Lance Lefebure

  I have two servers running SQL 2008 R2 Standard, each with an instance named "MAIN". I have a small test database on my primary server (one table, 13 rows) that I want to replicate to a second server as a proof-of-concept for some larger databases that I want to replicate. I set up the primary server to be a publisher and distributor, and set the database to do transactional replication. I copied the data to the second server via a backup/restore, not via a snapshot (which I'll have to do with the larger databases due to database size and limited bandwidth). I followed the instructions here: http://gnawgnu.blogspot.com/2009/11/sql-2008-transactional-replication-and.html Now on the subscriber, I go under Replication / Local Subscriptions / Right click / Properties on my subscription to the DB. The status of the last synchronization shows a status of: "The process could not connect to Distributor 'PRIMARYSERVER\MAIN'." Data IS replicating from the primary to the secondary. Any record I add on the primary shows up on the secondary server within seconds. Is the Distributor part of the Snapshot system that I'm not using, or is it part of the transaction replication stuff? Thanks, Lance

  Read the article

• How do you monitor the health of a mirrored disk in Windows?

  - by NitroxDM

  I have a Mirrored Dynamic disk on my Windows 2003 Server. How do you monitor the health of the volume? Is there a way to have the server send an email when there is an issue with the volume? Is there a way to have the server run S.M.A.R.T. tests? EDIT: Nothing says WTF like logging into a client server, running DISKPART LIST VOLUME and seeing this. Volume ### Ltr Label Fs Type Size Status Info ---------- --- ----------- ----- ---------- ------- --------- -------- Volume 0 X xDrive NTFS Mirror 233 GB Failed Rd Volume 1 C NTFS Simple 57 GB Healthy System Volume 2 D DVD-ROM 0 B Healthy Volume 3 F RAW Partition 466 GB Healthy Volume 4 E New Volume NTFS Partition 932 GB Healthy

  Read the article

• All Tasks..Advanced Operations option missing from Certificaces MMC Snap-In

  - by JohnFx

  I am trying to follow the instructions in this article to create a custom certificate to support SSL on a web server. I'm stick on the following step: Click on Personal – All Tasks – Advanced Operations – Create Custom request The problem is that on the web server (Windows Server 2003 R2) I don't have an "Advanced Operations" option under "All Tasks". I do on my desktop machine (Windows 7), but not on the server. All the documentation I can find indicates that it should be available on WS-2003-R2, but it just isn't. Note: I'm going through this manual process because I need to specify a alternate host names in the CSR, which you can't do through the IIS 6.0 console certificate managment functionality. Any suggestions for how to make this option show up?

  Read the article

• No write access on Windows 2008 workgroup share

  - by Serge - appTranslator

  Hi All, I'm trying to access network shares on my new Windows 2008 server (workgroup) using my server's local admin account. I can read files but not modify them. Permissions (sharing + file system) say: Users = Read only. Admins = Full Control. Even though I connect using my admin account (net use x: \\server\share /user:server\me), I can't write. OTOH, I have another share on the same computer where users have Read AND Write. I can write into that one. What's the problem? Does it have to do with UAC? TIA for your help.

  Read the article

• How much RAM on a windows VPS (2003, 2008, 2008R2)

  - by Pietro

  Right now I'm running Windows Server 2003 on a VPS with 640mb RAM and it works fine. I would like to upgrade OS to Windows Web Server 2008 or Windows Web Server 2008 R2. I understand that it is difficult to say how much RAM is needed, but can you make a comparison between 2003 and the two new 2008 versions? RAM on VPS is by far the most expensive item, so I wonder if I can get similar performances with 1GB and 2008 or 2008R2 compared to 640MB and 2003. Basically I run IIS, SQL Server and MailEnable.

  Read the article

• What is this service called in English?

  - by moomoochoo

  DETAILS I'm not familiar with server administration and am trying to find the name of a particular service offered by a Japanese website provider. The service is for a dedicated server. I have attached a picture detailing the service below. The left side of the picture shows the server without the service. The right side shows the server with the service. Once I know the name of the service I will Google it, but any additional information in regards to the pros and cons of such a service would be much appreciated. Thanks! QUESTION What is the name of the service in the picture. What are the pros and cons of this service?

  Read the article

• Win2008 - restrict VPN user permissions

  - by Sebas

  Windows 2008 R2 SP1 Foundations file server with no AD, only workgroup sharing some folders, and now a RRAS server. Shared folders are open to everyone in the office (XPs and Sevens) without accounts/passwords, but I was thinking about partially limiting access to the new "VPNuser" account. I'm new to Windows Server and its permissions settings: I thought about denying access to vpnuser through NTFS rights in some folders. It doesn't work, but now I'm guessing that the vpnuser is not considered as a logged user (doesn't appear as such) and is considered a "guest", like the rest of people connecting in the office. I say that because of this: http://social.technet.microsoft.com/Forums/windowsserver/en-US/ff6d3726-ff41-4d3f-9d97-5361af0206dd/vpn-users-on-server-shows-as-guest?forum=winserverNIS Also, because when I create a txt file using the VPN connection, owner field shows in description as "guest". Am I right? How can I set different rights for the VPNuser from the rest of "guest" users in the office?

  Read the article

• IIS 7 and ASP.NET State Service Configuration

  - by Shawn

  We have 2 web servers load balanced and we wanted to get away from sticky sessions for obvious reasons. Our attempted approach is to use the ASP.NET State service on one of the boxes to store the session state for both. I realize that it's best to have a server dedicated to storing sessions but we don't have the resources for that. I've followed these instructions to no avail. The session still isn't being shared between the two servers. I'm not receiving any errors. I have the same machine key for both servers, and I've set the application ID to a unique value that matches between the two servers. Any suggestions on how I can troubleshoot this issue? Update: I turned on the session state service on my local machine and pointed both servers to the ip address on my local machine and it worked as expected. The session was shared between both servers. This leads me to believe that the problem might be that I'm not using a standalone server as my state service. Perhaps the problem is because I am using the ip address 127.0.0.1 on one server and then using a different ip address on the other server. Unfortunately when I try to use the network ip address as opposed to localhost the connection doesn't seem to work from the host server. Any insight on whether my suspicions are correct would be appreciated.

  Read the article

< Previous Page | 448 449 450 451 452 453 454 455 456 457 458 459  | Next Page >