Search Results

Search found 13776 results on 552 pages for 'high technology'.

Page 452/552 | < Previous Page | 448 449 450 451 452 453 454 455 456 457 458 459  | Next Page >

• Improve wireless performance

  - by djechelon

  Hello, I have a Trust Speedshare Turbo Pro router, which is running on channel 6. I found that the wireless signal (and network performance) dramatically drops from my PDA (I can barely attach to the network, even if I set the PDA's energy settings to maximum wireless performance) when I even exit my room, and I don't have shielded walls or something like that. I can't even stream a SD video from my desktop (connected via LAN) to my laptop using WiFi, while via LAN it works fine. I read that changing router's channel could improve performance due to interference reducing. I found that almost all wireless networks around here run on channels 6 and 11. I tried to go to my router's settings page to change channel, but I found that the combo box only allows me to select 6!! I'm not sure, but I may have been able in the past to change channel, though not to all of the available channels. A few minutes ago I tried a firmware upgrade, but it didn't solve my problem. My question is Is it possible that my router is someway locked to its channel? I bought it on my own, I didn't receive it from my ISP Apart from boosting the antenna power to the maximum (which, by the way, increases the EM radiation my and my family's bodies absorb 24/7 and is little more environment-unfriendly), do you have any tips on getting high quality transmission up to 5 metres from the antenna? Thank you

  Read the article

• No sound out of headphone port on laptop

  - by Thanatos

  I cannot get sound out of the headphone port on a laptop. Headphones are plugged in, and sound comes out of the internal speakers. Windows behaves normally (sound switches to headphones when headphones are inserted). It did work in Linux at one point, but something changed, we're just not sure what. Rebooting doesn't fix. This appears to occur whether or not PulseAudio is running. Things I've tried: Rebooting. No effect. Booting into Windows. It works properly, so probably not a hardware issue. All of alsamixer. My only controls are this: "Master" Volume bar & mutable, unmuted. Controls volume. "PCM" Volume bar only. 100%. "S/PDIF" Mutable only, currently muted, has no effect. "S/PDIF" Default PCM", Mutable only, currently unmuted, has no effect. Killing PulseAudio. No effect. (It also won't stay dead! Something appears to be restarting it, and I can't tell what, but it is annoying as fuck.) alsactl init 0, no effect. sudo rm -f /var/lib/alsa/asound.state, no effect. General system info: Ubuntu 10.04 LTS Toshiba Satellite T135D-S1324 lspci says I have: 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller Some edits: Yes, the headphones are in all the way. This works in Windows: You plug headphones in, the internal speakers stop making noise, and noise comes out the head phones. Windows says I only have two sound cards: the HDMI port (which I don't care about) and the "sound card", which it claims is a "Conexant Pebble High Definition SmartAudio" In Windows, both the internal speakers and the headphone jack show up as one soundcard, which in my experience, is typical. (This is a laptop)

  Read the article

• i7 Windows 7 laptop or Macbook Pro 15" (For making 3D model and Animation)

  - by sppdhs

  Hi everyone, I'm thinking of buying a new laptop as my current one will be 5 years old next year and it currently gives me a blue screen everytime I run a heavy software to make 3D models and animation. Question is: Should I buy Macbook Pro or a Windows 7 laptop? I tried to research and some say that Windows would be better, especially because you can buy a very high spec laptop with cheaper price. While some other say Macbook Pro is the better choice as it can run bootcamp with windows 7 100% performance on every software even though it's a mac. Is this true? Which one is actually better? Btw, the software that I usually use is 3Ds Max, Maya, and ZBrush. To note as well, I have never used a Mac before. I've checked around some stores and budget wise, I'll need around AU$3000+ to buy a Macbook pro, and AU$2000+ to buy a windows laptop. Quite a big difference in price range. Thanks in advance for your help.

  Read the article

• Switched from DVI to HDMI, possible audio artifacts?

  - by I take Drukqs

  I'm using an ASUS VH236H monitor and an EVGA GeForce 570 GTX both of which are brand new. My monitor has an audio out port for speakers/headphones so I plugged in my headphones and made a random selection from my library when I noticed two things: There are static-like artifacts during "louder" parts of songs. There's what seems to be a volume cap in place. When I crank the volume past 100% in VLC the decibel level does not truly increase but the amount of static does. The cable is not new; I yanked it off of my PS3 when my DVI cable broke. It has been used a good amount on my HDTV and PS3 so I doubt it's a matter of burn-in. I like the way the setup works with an HDMI cable as opposed to DVI because my headphones barely reach my rig whereas I have plenty of slack when they're plugged into my monitor. Thanks in advance for any support. Note: I'm using a high quality HDMI cable from monoprice, AKG K702 headphones, and VLC media player.

  Read the article

• AWS: Multi-region setup using single RDS instance

  - by Ion

  I'm trying to scale our web application (PHP, MySQL, memcache) in a multi-region scheme. Currently we are using a setup with two EC2 instances behind an ELB and an RDS instance, all of them in US-EAST (Virginia) region. We would like to have a presence in the EU (Ireland) region as well. This means at least a new EC2 instance there (identical to the others, serving the same application). I have copied the desired AMI, setup the new instance, setup a same ELB configuration (required for SSL termination) and configured latency-based routing in Route53. And it works as suggested. But, clients from EU have speed problems. This is due to the fact that the EU EC2 instances connect to the US-based RDS instance. As far as I know Amazon has not yet enabled RDS multi-region replication. Do you have any suggestions on how to properly speed up the whole setup while using the single RDS instance? Also, any ideas in general on how to scale things up? Ideally we would like to continue using the RDS technology for various reasons. Nevertheless, I am open to suggestions (I guess the next idea would be to host our own MySQL servers).

  Read the article

• 3000 videos songs... some are loud in voice & some low.. I want to make them equal (equal in volume only)

  - by Mister.9

  I have thousands Video flv/avi files, which are all songs only. Some of them are high in volume and some are low. Every time the song ends I have to up or down the volume at once..to escape my ears ruined by headphones... and by woofers, save my life from my neighbor sleeping after hard-earning all the day long. :-( Any idea to make all files sound equal? Does such kind of application/software exist? Any converter that may convert all audio files into same volume? I know iTunes has sound-check option but can it convert? If I want to write CDs, does any burner have the feature like this, to burn in equal sound? If yes, suggest something for me... For, I am really really worried... It would be a great help..... Hoping your kind reply, Thanks in advance! (I am I am John.martin188@yahoo for having mails also in this regard)

  Read the article

• Home Server: storage virtualisation, what to choose?

  - by Huygens

  I'm looking for virtualisation solutions for storage and OS for a home server. A sort of private cloud where I manage the storage space independently of the VM one. This question focus on storage management. (I have another question related to the VM/compute instance management). Here my environement and wishes. Server: HP Proliant MicroServer with 8 GB RAM (AMD Turion dual core with AMD-V technology) with 1 250GB system disk and up to 4 HDD (2 TB) for "data" OS types: only Linux (perhaps a *BSD VM in the future) Linux distributions do not matter, I'm familiar with RHEL, Fedora, Suse, Ubuntu, but any other recommandation will be fine The 4 HDD is going to be a software RAID array, probably RAID 5. storage should be "virtualised/cloudified": easy to extend: if I add a NAS on the network, I can include the NAS space capacity within this storage space as one virtual disk. This can be a NAS, an external HDD or another server. cluster FS or S3 style space or OpenStack block storage? Whatever is easier to manage/maintain and easy to integrate/plug to VM/compute instance. I would prefer free (libre, as in a free speach) and open source tools. But it does not have to be free as in a free beer. Note: the VMs I intend to run on top of this server are one dedicated to backup, one for a "owncloud/dropbox"-like service and perhaps one for media server (hosting video and photos). I'm not sure if traditional VMs or compute instance are the most suitable for this.

  Read the article

• Video card not detected in POST on initial boot.

  - by Jeff M

  I have a minor problem with my desktop computer after cleaning it out for dust. When I first boot up the computer, the video card does not get detected so I can't see anything. In POST, I'm getting the "can't detect video card" beeps. The boot sequence continues normally, just without video. However, if I restart it (using the restart button) anytime after POST, it would boot up normally. I have no reason to think that the motherboard, video card or PSU got damaged in the process. It was working fine before, works fine after resetting. Took all the necessary precautions while cleaning. On the initial boot, I can hear the video card's fan power up but immediately power down and try again one more time only to fail. After the beep, resetting gets everything running and sounding normally. I've reseated the card a couple of times and reset the BIOS but doesn't seem to help. I'm hoping I won't have to take it out and remove and reinstall everything again. Does anyone recognize these symptoms to know exactly what the problem is? My guess is that the video card isn't getting enough juice initially to be running stable to be detected. I just don't know what I did (or didn't do) to get it to be in this state. It's not a high priority thing for me at the moment, just means I have to always reset it after initially turning it on but will eventually remove everything and reinstall if it comes to that. I don't think the specs are relevant here but just in case, here's the relevant stuff: Motherboard: Gigabyte P35-DS3P Video: EVGA GeForce 8600 GTS PSU: Antec True Power Trio 650W Built ~2 years ago, still running well

  Read the article

• What is the best private cloud storage setup

  - by vdrmrt

  I need to create a private cloud and I'm searching for the best setup. These are my 2 most important requirements 1. Disk and system redundant 2. Price / GB as low as possible The system is going to be used as backup setup which will receive data 24/7 over SFTP and rsync. High throughput is not that important. I'm planning to use glusterfs and consumer grade 4TB hard-drives. I have worked out 3 possible setups 3 servers with 11 4TB HDD Setup up a replica 3 glusterfs and setup each hard drive as a separate ext4 brick. Total capacity: 44TB HDD / TB ratio of 0.75 (33HDD / 44TB) 2 servers with 11 4TB HDD The 11 hard-drives are combined in a RAIDZ3 ZFS storage pool. With a replica 2 gluster setup. Total capacity: 32TB (+ zfs compression) HDD / TB ratio of 0.68 (22HDD / 32TB) 3 servers with 11 4TB consumer hard-drives Setup up a replica 3 glusterfs and setup each hard-drive as a separate zfs storage pool and export each pool as a brick. Total capacity: 32TB (+ zfs compression) HDD / TB ratio of 0.68 (22HDD / 32TB) (Cheapest) My remarks and concerns: If a hard drive fails which setup will recover the quickest? In my opinion setup 1 and 3 because there only the contents of 1 hard-drive needs to be copied over the network. Instead of setup 2 were the hard-drive needs te be reconstructed by reading the parity of all the other harddrives in the system. Will a zfs pool on 1 harddrive give me extra protection against for example bit rot? With setup 1 and 3 I can loose 2 systems and still be up and running with setup 2 I can only loose 1 system. When I use ZFS I can enable compression which will give me some extra storage.

  Read the article

• Performance data collection for short-running, ephemeral servers

  - by ErikA

  We're building a medical image processing software stack, currently hosted on various AWS resources. As part of this application, we have a handful of long-running servers (database, load balancers, web application, etc.). Collecting performance data on those servers is quite simple - my go-to- recipe of Nagios (for monitoring/notifications) and Munin (for collection of performance data and displaying trends) will work just fine. However - as part of this application, we are constantly starting up and terminating compute instances on EC2. In typical usage, these compute instances start up, configure themselves, receive a job from a message queue, and then get to work processing that job, which takes anywhere from 15 minutes to over 8 hours. After job completion, these instances get terminated, never to be heard from again. What is a decent strategy for collecting performance data on these short-lived instances? I don't necessarily need monitoring on them - if they fail for whatever reason, our application will detect this and handle re-starting the job on another instance or raising the flag so an administrator can take a look at things. However, it still would be useful to collect information like CPU (user, idle, iowait, etc.), memory usage, network traffic, disk read/write data, etc. In our internal database, we track the instance ID of the machine that runs each job, and it would be quite helpful to be able to look up performance data for a specific instance ID for troubleshooting and profiling. Munin doesn't seem like a great candidate, as it requires maintaining a list of munin nodes in a text file - far from ideal for an environment with a high amount of churn, and for the short amount of time each node will be running, I'd rather keep the full-resolution data indefinitely than have RRD water down the data over time. In the end, my guess is that this will require a monitoring engine that: uses a database (MySQL, SQLite, etc.) for configuration and data storage exposes an API for adding/removing hosts and services Are there other things I should be thinking about when evaluating options? Perhaps I'm over-thinking this, though, and just ought to run sar at 1-minute intervals on these short-lived instances and collect the sar db files prior to termination.

  Read the article

• Salary Survey Entry Level network position [closed]

  - by will

  Hello, I started interning with a company about 5 months ago and for the past 7 months I have been a normal part time employee. This week I have a review, where I am hoping to get a raise. I started at $8 interning, and now I'm up to $13. What I am trying to figure out is how to survey what others are making in similar positions so I can take it to the review as a base number. here are my thoughts on my position right now. Review Thoughts My Qualifications: • Associates of applied Science - IT network Specialist • CompTIA A+ certification • CompTIA Server+ certification • CompTIA Network+ certification • Currently pursuing Cisco certifications • Junior status at Insert college Pursuing Bachelors in Information Technology with an emphasis in Networking. 3.4 GPA • 1 year of working at Insert Company. My contributions to Insert Company • Offering near fulltime through semester and fulltime through summer. • Ability to work after hours and on weekends • Developed and support helpdesk system • Set up and maintain Update server to keep desktop clients up to date • Deployed and maintain antivirus solution for end users • Assist with main projects such as SAN, Virtualization, and network survey. Any tips on determining an asking number would help. I was thinking $17-$18, am I way off here? • Migrating end user stations to Windows 7 (current project) • Developing imaging solution for Desktop PCs (current project)

  Read the article

• Disk usage on IIS, PHP5, performance problems.

  - by Jacob84

  Hi everybody, I'm quite worried with a performance problem that I'm facing in one of our production servers. I'm working for a hosting company, so you can imagine how heterogeneous the applications runnning here are. All started with a call of a client complaining about the speed loading a Joomla. The setup is IIS6 (Windows 2003) with PHP5 and FAST CGI wich normally works pretty well. I've tested the loading time and indeed, he was right. 7 or 8 seconds to load, when usually this can be accomplished in 2. Seeing this results, I started to check first CPU and RAM. Everithing normal, 2GB of RAM free, 3%-8% of CPU activity. That's what I call a relaxed server ;). Unfortunately, digging a little deeper I've found the 'PhysicalDisk' counters quite high (above 10), specially the read queues. I've used Process Explorer to see wich of those processes has the higher deltas, but everything seemed normal. As the problem is specially related to PHP pages, I've checked specific IIS counters, as Actual connections, Number of CGI requeriments and Number of ISAPI requeriments. CGI -> 3 to 7 ISAPI -> 5 to 9 Connections-> 90 to 120 (wich appears at the top of the graph) More than a solution (I know this is hard to find), I would like to know if you have an specifical methodology to face this kind of problems. Thanks a lot, as always.

  Read the article

• Is Hyper-V server suitable as a desktop testbench?

  - by Thomas.Winsnes

  At the moment we are running a test bench with several desktop computers, that are reimaged every time we need to test on a different operation system. Also because different versions of our software is tested on each image, we have to install our software every time we want to test it. The problem we have had with going with a virtualization technology is that our software is depending on directx/opengl and 3D acceleration, and this has not been something that virtual machines have excelled at. With the release of SP1 for Windows 7 and Server 2008 R2 Hyper-V has gotten better 3D acceleration support, so we are looking into virtualizing our testbench using this. Our test scenario would most likely be something close to this: 1. Remote into the hyper-V server and load the test VM needed for the current tests 2. Remote into the VM and install the new version of the software 3. Run the tests It would be nice, but not essential, if our support team could remote into the VMs to match the users OS+software combination when doing support. Does anyone have any experience with this kind of settup with hyper-v?

  Read the article

• How to diagnose storage system scaling problems?

  - by Unknown

  We are currently testing the maximum sequential read throughput of a storage system (48 disks total behind two HP P2000 arrays) connected to HP DL580 G7 running RHEL 5 with 128 GB of memory. Initial testing has been mainly done by running DD-commands like this: dd if=/dev/mapper/mpath1 of=/dev/null bs=1M count=3000 In parallel for each disk. However, we have been unable to scale the results from one array (maximum throughput of 1.3 GB/s) to two (almost the same throughput). Each array is connected to a dedicated host bust adapter, so they should not be the bottleneck. The disks are currently in JBOD configuration, so each disk can be addressed directly. I have two questions: Is running multiple DD commands in parallel really a good way to test maximum read throughput? We have noticed very high SWAPIN-% numbers in iotop, which I find hard to explain because the target is /dev/null How shoud we proceed in trying to find the reason for the scaling problem? Do you thing the server itself is the bottleneck here, or could there be some linux parameters that we have overlooked?

  Read the article

• Best way to build / implement a corporate developer Linux distro with multiple kernels?

  - by Garen

  At work we have Linux users who understandably prefer using Ubuntu. Problem is, we also have developer tools that only work with 'officially' supported Linux distributions that use much older 2.6.18 based kernels. (And even if they worked with newer ones, the vendors could always say they won't "support" the software unless it's on one of their 'officially' supported platforms.) We could of course just tell them to use CentOS or something else 2.6.18-based, and I'm sure their response would be something like: "you can take Ubuntu from our cold, dead hands." :) Which brings to me some questions--is there any good/easy/recommended way to run something like Ubuntu as a host VM and Centos 5.x as a guest OS (with which system--Xen,KVM,VMWare, ...?), and then roll that into our own custom internal distribution that could be easily installed? KVM looks like a good high-performance option just recently included in RHEL 5.4, but if hardware support for virtualization like Intel-VT or AMD-V is necessary, then I'd guess only those folks with fairly new PCs will be able to do it. Would be very interested to hear how anyone else has addressed this kind issue. EDIT: The target audience / users of this kind of system would be developers, each one needs to run locally licensed commercial software, so building out some separate beefy central machines isn't an option unfortunately due to license restrictions. Even if that weren't the case, a couple developers could quickly eat up the resources with parallel builds. :) Ideally, I was hoping there was some step-by-step guide out there to build your own pre-built distribution that had e.g. CentOS 5.x and Ubuntu Desktop as a guest.

  Read the article

• Intel Ethernet Bottlenecking Internet?

  - by Donald Darma

  I'm having trouble with my internet speeds. So I just recent build a pc and everything is fine. I installed the Intel drivers and connected to the internet. It connects but I'm only half the speed I should be getting. My normal speed is 20mbps but speedtest.net is only showing 10. It can't be my ISP (which is TWC if anyone is asking) because my other devices like my laptop and my smartphone are showing 20 down. Heres my system: CPU: i5 4430 HSF: Stock cooler Mobo: Gigabyte Z87MX-D3H GPU: x2 MSI R7950-3GD5/OC BE RAM: Crucial Ballistix Tactical Tracer 8GB dual channel PSU: Silencer High Performance Power Supply 750 Watt 80+ (It's a subdivision of OCZ) HDD: Seagate Barracuda 7200RPM 3TB SSD: Samsung 840 Evo 120 GB Case: Corsair Obsidian 350D Edit: I am using the stock adapter that is on the motherboard. I know for a fact that the cable is good because I used it on my laptop and it ran fine. Its a CAT5E cable. I also ran IPERF and its giving me the same results, 10 mbps.

  Read the article

• How to manage unprivileged administration of system services using Debian?

  - by ypnos

  At our lab, we have several services handled by different phd students (like myself). Fluctuation is high and people do the job next to their research duties. Until now, services were running on different machines, with different OS setups that can result in administration hell quickly. We want to consolidate our service setup. Our main idea is that the guys responsible for the services should not meddle with the underlying system anymore. Apart from core systems like NFS and kerberos, a typical service is able to run as non-root already. I'm talking about apache, mysql, subversion, mail with openxchange, and so on. Redirecting privileged ports is also no issue (source). What is left is the configuration of the service and its payload. One scenario we envisioned is that every service has its own user and home directory, accessable by the corresponding admins. Backup and fallback of the service is easy, as everything needed for the service to run is found in one place. Are there established ways to create such a setup? Does a mostly unique method exist to make services find their files (other than in system directories) while still using the corresponding debian packages? Are there any catches with our idea that we may have overlooked? Would you maybe claim that virtualization is the answer to our problem? (In our POV, it wouldn't help us keeping system setup strictly separated from service setup.) Thank you for any advice!

  Read the article

• Log shipping on select tables.

  - by Scott Chamberlain

  I know I am most likely using incorrect terminology so please correct me if I use the wrong terms so I can search better. We have a very large database at a client's site and we would like to have up to date copies of some of the tables sent across the internet to our servers at our office. We would like to only copy a few of the tables because the bandwidth requirement to do log shipping of the entire database (our current solution) is too high. Also replication directly to our servers is out of the question as our servers are not accessible from the internet and management does not want to do replication (more on that later). One possible Idea we had is to do some form of replication on the tables we need to another database on the same server and do log shipping of that second smaller database but management is concerned that the clients have broken replication (it was between two servers on their internal network however) on us in the past and would like to stay away from it if possible. Any recommendations would be greatly appreciated. If using some form of replication is the only solution, I am not against replication, I just need compelling arguments to convince management to do it. This is to be set up on multiple sites that are running either Sql2005 or Sql2008 we will have both versions on our end to restore the data to so that is not a issue. Thank you.

  Read the article

• Can't mount Linux usb disk. It just create /dev/sg device but no /dev/sd

  - by MTilsted

  I have a Corsair R60 ssd disk which is a disk with both sata and usb connectors. But the usb thing seems to be a bit non-standard, or maybe its just my fedora linux. When I insert the disk using a usb cabel to a running Fedora 14 linux system, a device called /dev/sg3 is added but that is all. No new /dev/sd* device is created so I can't mount the disk. If I look at cat /proc/scsi/sg/device_strs I get ATA Hitachi HTS54321 FB2O HL-DT-ST DVDRAM GSA-T50N RP05 Seagate Desktop 0130 Corsair CSSD-R60GB2 So the disk is there. (The last entry) but my linux will for some reason not see it as a usb hard disk. When I insert other usb disks they work fine. It is only this specific disk which causes problems. I have tried on 3 different computers with the same result. A hint to the problem may be that if I add the disk to a windows system(With usb) the disk is called "A fixed disk" and not a portable disk as expected. The disk works fine with linux If i connect it with the sata cabel, but I would really like to have it working with usb too. (To mount it on computers without sata). Added: I did try to mount /dev/sg3 but mount say that its not a block device. (File say Its a character special device). Added output from dmesg: [ 97.454073] usb 7-1: USB disconnect, address 2 [ 105.913055] hub 2-0:1.0: unable to enumerate USB device on port 3 [ 107.048054] usb 2-3: new high speed USB device using ehci_hcd and address 5 [ 107.162900] usb 2-3: New USB device found, idVendor=1b1c, idProduct=1ab8 [ 107.162903] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=5 [ 107.162906] usb 2-3: Product: CSSD-R60GB2 [ 107.162908] usb 2-3: Manufacturer: Corsair [ 107.162910] usb 2-3: SerialNumber: 10111441000000990069 [ 107.167651] scsi7 : usb-storage 2-3:1.0 [ 108.195543] scsi 7:0:0:0: Direct-Access Corsair CSSD-R60GB2 PQ: 1 ANSI: 0 [ 108.197732] scsi 7:0:0:0: Attached scsi generic sg3 type 0

  Read the article

• Wired to wireless bridge in Linux

  - by adrianmcmenamin

  I am attempting to set up my Raspberry Pi as a bridge (but I think this is not a question specific to the hardware) - using Debian wheezy. I have a hostapd.conf: (some details changed for security)... interface=wlan0 bridge=br0 driver=nl80211 auth_algs=1 macaddr_acl=0 ignore_broadcast_ssid=0 logger_syslog=-1 logger_syslog_level=0 hw_mode=g ssid=MY_SSID channel=11 wep_default_key=0 wep_key0=MY_KEY wpa=0 (yes, I know WEP is no good) And this in /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp allow-hotplug wlan0 iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp auto br0 iface br0 inet dhcp bridge-ports eth0 wlan0 Everything seems to come up ok, but I cannot associate with the bridged wireless connection - even though the flashing lights on the USB stick suggest packets are being exchanged. I have read somewhere that not all cards/devices will run in hostap mode - they won't pass packets in one direction: is that right? (The info was a bit old)- this my card: [ 3.663245] usb 1-1.3.1: new high-speed USB device number 5 using dwc_otg [ 3.794187] usb 1-1.3.1: New USB device found, idVendor=0cf3, idProduct=9271 [ 3.804321] usb 1-1.3.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48 [ 3.816994] usb 1-1.3.1: Product: USB2.0 WLAN [ 3.823790] usb 1-1.3.1: Manufacturer: ATHEROS [ 3.830645] usb 1-1.3.1: SerialNumber: 12345 So, what have I got wrong here?

  Read the article

• Why am I seeing Zero errors in non-ECC RAM?

  - by Alexander Shcheblikin

  According to sources, memory errors are a very probable event: Some say the probability of a DRAM error is 95% in just 3 days of operation of a computer with just 4 GB of RAM, others say 32% of servers experience at least one error in a month with 8% of DIMMs being at fault. Contrary to those horrors, in my more than 10 years of personal computers use I have seen exactly none of the memory errors. I admit I never paid special attention to the subject. However, I have ventured multi-hour memtest86 runs couple of times and never seen an error either. Some of the factors that IMO should aggravate the memory problems: I build my computers out of the most "bulk commodity" parts: mainstream budget motherboards and the next to cheapest memory. also I usually max out the technology available, e.g. in the times of 32 bit OS'es I used 4 GB of RAM and with the current desktop CPUs and the newer 64 bit OS'es I use 32 GB of RAM. memory usage is moderately heavy with lots of virtual machines up running small and big tasks 24/7/365. But nevertheless, no memory-related problems ever found! How's that?

  Read the article

• Migrating JBoss installation and install it on a PHP server

  - by David Martinez

  I'm configuring a new dedicated server that is going to run 3 sites, 2 of then are migrating from a old server. Each site have it's own domain and dedicated ip. 2 of this sites are already up and running on php (one of then use cakePHP), the third site is a migration from an old server and it runs on JBoss. 1) Is it possible to have both Jboss and php running on the same Apache instance, or would I have to install a new one? 2) Can I just move the old JBoss server directory to the new server and start the server with the shell script? From what I red here JBoss is distributed as a zip/tgz file with the server structure, so moving it from the old server to the new one should be the same. I want to do this because the old server is already configured, and it have 2 JBoss instances. I didn't develop this site and I don't have experience with JBoss. I have some documentation of the site, but it is not much, mostly server structure and the technology they used. The new server runs on CentOS with CPanel, I have full root access to the server. This question is similar to this one How can I run JBoss Application Server and Apache on the same server? but there he didn't have a dedicated IP for each domain.

  Read the article

• VMWare Workstation 8 Disk I/O & Hard Faults

  - by Scott

  I have VMWare Workstation 8 installed on a host machine with the following specs: Intel i5 2500k CPU 16GB DDR3 1600 ram 1TB Western Digital Caviar Black HD I have two Windows 7 virtual machines configured (currently running one at a time but will be operating both at once when my 32GB RAM kit arrives in a couple days). Each one is configured with 8GB of RAM and no tweaks/performance customizations or anything done. All of the VMWare settings are the defaults. When I boot into these machines and run various programs (Visual Studio, Outlook, etc), I can hear the disk thrashing quite a bit and checking Resource Monitor, I can see that I'm getting anywhere between 300-800 hard faults per second. From the host machine, it shows they're coming from the VMWare image. If I go to the virtual machine, whatever app I'm currently loading is the image that's causing the hard faults. As I understand it, hard faults are (simply) when an address in memory has been swapped out to the page file and has to be read from the page file instead of from memory. I don't understand why this is happening though. With 8GB of ram on the guest machine and 6.5GB available, what could be causing this? I know Windows 7 supposedly improved on page file management over XP but it seems excessive for this kind of slowdown, disk thrashing and high hard fault count when I have that much free RAM. Is there anything I can to to improve the performance in my guest machines? On the host machine, I can open/run any applications at all and hard faults stays around 0 with low disk I/O.

  Read the article

• h264 inside FLV container vs. MP4 container?

  - by Gotys

  I am developing a tube site, and currently having issues with h264 format . By looking at youtube, I noticed they are putting their hi-def videos into mp4 container, so logically I did the same. Next, I installed mod_h264_streaming for lighttpd to make streaming and timeline-scrubbing work. Problem is, that large files (500mb+ at somewhat high resolution) take for EVER to even start buffering ( I read the flowplayer or other flash players need to download metadata first) . I moved the xmov atom to the front of the file with MP4Box (i tried qt-quickstart too) , and the problem didn't go away. Next I read online I need to interleave audio tracks, so I did that too. No change in slowness. So I tried putting the same exact h264 movie into an FLV container, and the playback buffering starts almost instantly - no slowness. So what am I missing here? Why would I choose MP4 container with mod_264_streaming module , which seems super-slow over a regular FLV container with lighttpd's built-in mod_flv_streaming ? Obviously many websites pick mp4 container , but I fail to understand why ? And as a side question - I tried using HTML5's VIDEO tag to try the same h264 MP4 movie, and the scrubbing is LIGHTING FAST! I looked into lighttpd's log file, and i noticed taht Flash Players append video.mp4?start=234 each time timeline is scrubbed, wheres HTML5's video tag does no such thing . Is this some sort of limitations of Flash ? Why Can't flash streaming be same fast as HTML5 streaming? Thanks to ALL who can help. I very much appreciate this community.

  Read the article

• Mesh Networked servers via vpn

  - by microspino

  I got a design idea and I would like to have some advice from SF about It. I have 5 customers with small real-estate databases. I've built for them a desktop app and now they would like to merge their database to share their data. I don't want to centralize everything in one place nor I want to do maintenance for servers. They told me also, that all of them in their offices, have little servers and maintenance guys available. Although everything seems suitable for web application, I had the idea to experiment something new: Any customer small-server wild be connected to the others in a sort of mesh network without a single point of failure and through VPNs. If one of the servers went down the customers could still connect to their databases from one of the other mesh networked servers instead of from the local one that is down. During normal operations all the servers sync the db with the others through VPNs. I can accept a half-day timing window of NON synched data, in other words, since I don't need real time synchronization, the server don't have to always stay in synch. I can migrate my data over to other Non-Sql technologies like CouchDB or Redis or whatever you suggest. As you can see I don't have a lot of constraints and although I could go with a web application I would like to delegate and decentralize support, data-privacy and management, as more as I can to my customers offices. Is that a crazy idea? Do you know If something similar exist? Which technology would you suggest?

  Read the article

< Previous Page | 448 449 450 451 452 453 454 455 456 457 458 459  | Next Page >