Search Results

Search found 23435 results on 938 pages for 'i give terrible advice'.

Page 454/938 | < Previous Page | 450 451 452 453 454 455 456 457 458 459 460 461  | Next Page >

• Amazon EC2 instance missing Network Interface

  - by Sergiks

  I am running Linux on a t1.micro instance at Amazon EC2. Once I noticed bruteforce ssh login attemtps from a certain IP, after litle Googling I issued the two following commands (other ip): iptables -A INPUT -s 202.54.20.22 -j DROP iptables -A OUTPUT -d 202.54.20.22 -j DROP Either this, or maybe some other actions like yum upgrade perhaps, caused the follwing fiasco: after rebooting the server, it came up without the Network Interface! I only can connect to it through AWS Management Console JAVA ssh client - via local 10.x.x.x address. Console's Attach Network Interface as well as Detach.. are greyed out for this instance. Network Interfaces item at the left does not offer any Subnets to choose from, to create a new N.I. Please advice, how can I recreate a Network Interface for the instance? Upd. The instance is not accessible from outside: cannot be pinged, SSH'ed or connected by HTTP on port 80. Here's the ifconfig output: eth0 Link encap:Ethernet HWaddr 12:31:39:0A:5E:06 inet addr:10.211.93.240 Bcast:10.211.93.255 Mask:255.255.255.0 inet6 addr: fe80::1031:39ff:fe0a:5e06/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1426 errors:0 dropped:0 overruns:0 frame:0 TX packets:1371 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:152085 (148.5 KiB) TX bytes:208852 (203.9 KiB) Interrupt:25 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) What is also unusual: a new micro instance I created from scratch, with no relation to the troubled one, was not pingable too.

  Read the article

• Extremely high mysqld CPU usage with no active queries

  - by RadarNyan

  I have a VPS running Ubuntu 12.04 LTS with LEMP stack, followed the guide from Linode Library (since I'm using a Linode) to setup, and everything worked fine until now. I don't know what's wrong, but my CPU usage just goes up since a week ago. Today things getting really bad - I got 74% CPU usage so I went check and found that mysqld taking too much CPU usage (somewhere around 30% ~ 80%) So I did some Google Search, tried disable InnoDB, restart mysql, reset ntp / system clock (Isn't this bug supposed to happen more than a year ago?!) and reboot my VPS, nothing helped. Even with mysql processlist empty, I still get mysqld CPU usage very high. I don't know what I missed and have totally no idea, any advice would be appreciated. Thanks in advance. Update: I got these from running "strace mysqld" write(2, "InnoDB: Unable to lock ./ibdata1"..., 44) = 44 write(2, "InnoDB: Check that you do not al"..., 115) = 115 select(0, NULL, NULL, NULL, {1, 0}^[[A^[[A) = 0 (Timeout) fcntl64(3, F_SETLK64, {type=F_WRLCK, whence=SEEK_SET, start=0, len=0}, 0xbfa496f8) = -1 EAGAIN (Resource temporarily unavailable) hum... I did tried to disable InnoDB and it didn't fix this problem. Any idea? Update2: # ps -e | grep mysqld 13099 ? 00:00:20 mysqld then use "strace -p 13099", the following lines appears repeatedly: fcntl64(12, F_GETFL) = 0x2 (flags O_RDWR) fcntl64(12, F_SETFL, O_RDWR|O_NONBLOCK) = 0 accept(12, {sa_family=AF_FILE, NULL}, [2]) = 14 fcntl64(12, F_SETFL, O_RDWR) = 0 getsockname(14, {sa_family=AF_FILE, path="/var/run/mysqld/mysqld.sock"}, [30]) = 0 fcntl64(14, F_SETFL, O_RDONLY) = 0 fcntl64(14, F_GETFL) = 0x2 (flags O_RDWR) setsockopt(14, SOL_SOCKET, SO_RCVTIMEO, "\36\0\0\0\0\0\0\0", 8) = 0 setsockopt(14, SOL_SOCKET, SO_SNDTIMEO, "<\0\0\0\0\0\0\0", 8) = 0 fcntl64(14, F_SETFL, O_RDWR|O_NONBLOCK) = 0 setsockopt(14, SOL_IP, IP_TOS, [8], 4) = -1 EOPNOTSUPP (Operation not supported) futex(0xb786a584, FUTEX_WAKE_OP_PRIVATE, 1, 1, 0xb786a580, {FUTEX_OP_SET, 0, FUTEX_OP_CMP_GT, 1}) = 1 futex(0xb7869998, FUTEX_WAKE_PRIVATE, 1) = 1 poll([{fd=10, events=POLLIN}, {fd=12, events=POLLIN}], 2, -1) = 1 ([{fd=12, revents=POLLIN}]) er... now I totally don't get it x_x help

  Read the article

• Reconnecting OST with Exchange

  - by syrenity

  Hi. I have a quite big problem with customer's MS Exchange. The server got it's disk filled about 2 weeks ago, so it's currently offline. They plan to upgrade it, but not in hurry, as they use it mainly for OWA and back-up - the mails exchange is done via SMTP and POP3. Trying to diagnose some problem today, one of the users has (following the ISP instructions), removed the Exchange account from Outlook, which essentially left the OST orphaned. The user naturally didn't move the emails or any other data to the Archive / PST before, so these emails located on the OST only. So currently I'm trying to figure out how to restore them. There are 2 options: 1) Make the user buy some tool to convert them to PST, and import as archive / main Outlok file? 2) Reconnect the Outlook to Exchange (once it up), let it sync the old server content, then shutdown Outlook and replace the new OST with the old one, start Outlook again in offline mode and move these files to archive. 3) Any other method? Can someone advice what would be the best approach here? The used versions are Outlook 2007 and Exchange 2003. Thanks!

  Read the article

• Creating Custom ISO Images

  - by ericl42

  I am working on creating some custom ISO images using primarily Fedora and CentOS. I want the image to be a bootable live CD with some specific files on it. I also want it to have the option to be able to be downloaded to the hard drive. I've read some various articles but want to get a few more opinions since I've never done this before. Currently I'm trying 2 different methods. Install Fedora with the configuration exactly how I want it and then run the livecd-tools program to pull everything I currently have to an ISO. I haven't got this to work yet but I do see a few issues with it. Such as the default passwords I had to put in. Run a Fedora live CD and install a few things I want on it and then copy the image of it. I believe this would work better since it has more of a live cd feel. However I"m not 100% sure how I should go about pulling the current image to my own ISO. I know some people have said to use mkisofs and a few other programs but any advice would be greatly appreciated.

  Read the article

• Running $ORIGIN linked binaries from setuid scripts on linux

  - by drscroogemcduck

  I'm using suidperl to run some programs that require root permissions. however, the runtime linker won't expand library paths which contain $ORIGIN entries so the programs i want to run (jstack from java) won't run. more info here There is one exception to the advice to make heavy use of $ORIGIN. The runtime linker will not expand tokens like $ORIGIN for secure (setuid) applications. This should not be a problem in the vast majority of cases. my program looks something like this: #!/usr/bin/perl $ENV{PATH} = "/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin:/usr/java/jdk1.6.0_12/bin:/root/bin"; $ENV{JAVA_HOME} = "/usr/java/jdk1.6.0_12"; open(FILE, '/var/run/kil.pid'); $pid = <FILE>; close(FILE); chomp($pid); if ($pid =~ /^(\d+)/) { $pid = $1; } else { die 'nopid'; } system( "/usr/java/jdk1.6.0_12/bin/jstack", "$pid"); is there any way to fork off a child process in a way so that the linker will work correctly.

  Read the article

• VMware NAS/iSCSI recommendations - smallish organization

  - by Bubnoff

  I have two VMware servers - ESX + ESXi. Two backup NAS boxes. The current NAS boxes are low-cost and unsuitable for running VMs from. Support NFS only. Slow. My plan is to have a dedicated iSCSI/NAS for storing and running VMs. Two additional low-cost boxes for backup. I'm looking for advice regarding 2 things really: Recommendations as far as VMware architecture/design for a smaller organization. Less than 20 Virtual Machines. 2 servers + 2 x 1.5 terabyte backup NAS boxes. A good NAS/iSCSI box with your recommendation on RAID config ...I would go with 6 or better. I'm trying to design an installation that is both fast and reliable/redundant. If you have any experiences to share or your current configuration including network design ( switches, fiber ...etc ), I will be enormously thankful. I'm not married to this idea, so if you have a design not using iSCSI NAS boxes ...let er rip. Cost? Can we stay around $5,000 ( on top of already stated components )? Links to info are welcome also. Thanks for reading! Bubnoff

  Read the article

• System State Backup Retention Policies

  - by isoscelestriangle

  I was wondering if there was a general consensus on how long to keep system state backups. I am trying to reevaluate our current backup process, and trying to get a good handle on our current storage requirements. Our current setup involves tapes and sending backups offsite with Barracuda Networks. We have been doing our system state backups with Barracuda now, which does full backups daily, leaving our storage requirements growing quite quickly. My boss is a little too gung-ho with backups and wants our system states saved for quite a while. We currently have 5 days of nightlies, 5 weeklies, 3 monthlies, and so on. I think this is quite overkill for system state backups. My boss wants the ability to go back in time to find when an issue appeared, but I don't think that is practical. Many things change in the course of several months. I also think it would be hard not to notice problems with our DCs and other servers for several months. I would think that a previous week's snapshot and the current week's dailies would suffice. Any advice or reading you can point me to? Thanks!

  Read the article

• Correctly setting up UFW on Ubuntu Server 10 LTS which has Nginx, FastCGI and MySQL?

  - by littlejim84

  Hello. I'm wanting to get my firewall on my new webserver to be as secure as it needs to be. After I did research for iptables, I came across UFW (Uncomplicated FireWall). This looks like a better way for me to setup a firewall on Ubuntu Server 10 LTS and seeing that it's part of the install, it seems to make sense. My server will have Nginx, FastCGI and MySQL on it. I also want to be allow SSH access (obviously). So I'm curious to know exactly how I should set up UFW and is there anything else I need to take into consideration? After doing research, I found an article that explains it this way: # turn on ufw ufw enable # log all activity (you'll be glad you have this later) ufw logging on # allow port 80 for tcp (web stuff) ufw allow 80/tcp # allow our ssh port ufw allow 5555 # deny everything else ufw default deny # open the ssh config file and edit the port number from 22 to 5555, ctrl-x to exit nano /etc/ssh/sshd_config # restart ssh (don't forget to ssh with port 5555, not 22 from now on) /etc/init.d/ssh reload This all seems to make sense to me. But is it all correct? I want to back this up with any other opinions or advice to ensure I do this right on my server. Many thanks!

  Read the article

• Sign multiple domains with single Domain Key (dk-filter)

  - by Lashae

  Motivation The private shopping website GILT, send periodical update emails from giltgroupe.bounce.ed10.net however all of the mails are signed with domain keys of giltgroupe.com. mailed-by giltgroupe.bounce.ed10.net signed-by giltgroupe.com My Story I couldn't manage to sign x.com with y.com 's domain key using dk-filter under Debian Lenny with postfix. If I try to init dk-filter service with following arguments: DAEMON_OPTS="$DAEMON_OPTS -d x.com,y.com -c nofws -k -i /var/dk-filter/internal_hosts -s /etc/dk-keys.conf" dk-filter service signs with domain x.com (d=x.com) If I change the daemon arg.s as following: DAEMON_OPTS="$DAEMON_OPTS -d x.com -c nofws -k -i /var/dk-filter/internal_hosts -s /etc/dk-keys.conf" then emails sent From y.com is not being signed. the dk-keys.conf file is as follows: *:/var/dk-filter/y.com/mail I managed to do same thing with DKIM, works perfect. However DK doesn't seem to work. I don't have any problem signing y.com's emails with y.com's key and x.com's emails x.com's key, which indicates there is no configuration problem. Do you have any experience/advice to make it possible to sign emails from multiple domains by a specific chosen domain?

  Read the article

• How to handle sh: fetch: command not found

  - by Tyler Johnson

  Okay, I'm a noobie. I know how to build and compose a website, but I have no idea what I'm doing when it comes to servers and server commands, etc. I've recently had a problem with all of my sites on our servers going down all at once and then I have to go in and reboot the server for them to come up again. At first this was annoying, but now it is becoming agonizing as it now takes 3-4 reboots for the websites to come back up. I contacted support for my hosting, but they are not being very helpful. They just keep telling me what the issue might be and basically telling me that I'm going to have to look into it and figure it out, which really isn't possible since I know nothing. Anyway, here are the things they said were possible reasons: They said I have "strange logs" in my Apache webserver log, error: sh: fetch: command not found. My php.ini memory limit is: 256M which is very high. It should be 32M or 64M. Server is reaching Max Clients, meaning we have more than 150 visitors at a time. (They supposedly "fixed" this, but the sites/server are still going down) I have some Wordpress sites with plugins getting errors like: PHP Warning: pack(): Type H: illegal hex digit G in... PHP Fatal error: Cannot use object of type stdClass as array in... PHP Fatal error: Maximum execution time of 30 seconds exceeded in... PHP Fatal error: Call to undefined function file_exists() in... PHP Parse error: syntax error, unexpected '<' I know that's a lot, but I really am at wits end and have no idea what to do now. If anyone could maybe give me some advice or point me in the right direction I would greatly appreciate it! Thanks! Oh, and here are the specs for my server: RAM: 2048MB CPU Shares: 40 Primary Disk: 50GB Data Transfer: 75GB Port Speed: 5Mbps

  Read the article

• How can I proxy multiple LDAP servers, and still have grouping of users on the proxy?

  - by Chris

  I have 2 problems that I'm hoping to find a common solution to. First, I need to find a way to have multiple LDAP servers (Windows AD's across multiple domains) feed into a single source for authentication. This is also needed to get applications that can't natively talk to more than one LDAP server to work. I've read this can be done with Open LDAP. Are there other solutions? Second, I need to be able to add those users to groups without being able to make any changes to the LDAP servers I'm proxying. Lastly, this all needs to work on Windows Server 2003/2008. I work for a very large organization, and to create multiple groups and have large numbers of users added to, moved between, and removed from them is no small task. This normally requires tons of paperwork and a lot of time. Time is the one thing we don't normally have; dodging the paperwork is just a plus. I have very limited experience in all this, so I'm not even sure what I'm asking will make sense. Atlassian Crowd comes close to what we need, but falls short of having it's own LDAP front end. Can anyone provide any advice or product names? Thanks for any help you can provide.

  Read the article

• How do I access my samba drive through several layers of network topology?

  - by stephenmm

  I have a new windows 7 Home Premium machine that is in a different room than my main computer area. As such I have to use a bridge and another router. Everything is working wonderfully except I cannot access the SAMBA drive with the new machine. I know that SAMBA is accessible as an older WinXP machine can access it. A picture of my network would probably be helpfull: To ISP | | +---------------------------+ | WAN | | Cable Modem | | (2WIRE678) | | | | | +---------------------------+ | +---------------------------+ | | (|) (|) +-----------+ | Belkin Router | | | | Wireless | | (F5D) |--+ +--| WinXP | | | |SAMBA USER | | | +-----------+ +---------------------------+ | | | | +------------+ | | Ubuntu | | | Apache + | | |SAMBA Server| | +------------+ | | +---------------------------+ | | | Netgear Bridge | | (XET1001) | | | +---------------------------+ # # +---------------------------+ | | | Netgear Bridge | | (XET1001) | | | +---------------------------+ | +---------------------------+ | | | D-Link Router | | (DI-524) | | | | | +---------------------------+ | | | | +-----------+ | | | Win7 | |SAMBA USER?| +-----------+ More interesting data points: 1. I can ping the SAMBA server from the Win7 machine locally (Ie. 192.168.2.2) 2. I can access the webserver from the Win7 machine locally (Ie. 192.168.2.2) 3. I followed the advice to get Win7 and SAMBA to play nice: http://www.tannerwilliamson.com/2009/09/windows-7-seven-network-file-sharing-fix-samba-smb/ Sorry for being so long winded but it is kind of complex and I am really at a loss as to how to fix it. If any of you have some suggestions I would love to hear it!

  Read the article

• e2fsck / resize2fs problems

  - by BlakBat

  I've got 6 drives (each 1.5T, all same model and firmware revision) that are part of a RAID5 array. The RAID5 makes a LVM volume group and a logical group. The latter contains only one ext3 partition. I've recently ran: e2fsck -f /dev/vg03/lv01 && resize2fs -M /dev/vg03/lv01 which exited without an error. Now when I try to mount /dev/vg03/lv01 I get: EXT3-fs error (device dm-0): ext3_check_descriptors: Block bitmap for group 30533 not in group (block 1000532368)! EXT3-fs: group descriptors corrupted! How do I get out of this predicament? This is all the info I can currently give you: fdisk -l /dev/sd[cdefgh] shows (correctly) that they are "Linux raid autodetect" but fdisk now shows: fdisk -l /dev/md0 Disk /dev/md0: 7501.5 GB, 7501495664640 bytes ... Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table (instead of a LVM type partition) fdisk -l /dev/vg03/lv01 Disk /dev/vg03/lv01: 7501.5 GB, 7501491732480 bytes ... Disk identifier: 0x00000000 Disk /dev/vg03/lv01 doesn't contain a valid partition table (instead of a ext3 type partition) I've tried: e2fsck -fy /dev/vg03/lv01 e2fsck 1.41.12 (17-May-2010) e2fsck: Group descriptors look bad... trying backup blocks... Block bitmap for group 30533 is not in group. (block 1000532368) Relocate? yes Inode bitmap for group 30533 is not in group. (block 1000532369) Relocate? yes Pass 1: Checking inodes, blocks, and sizes Relocating group 30533's block bitmap to 1000524246... Error allocating 1 contiguous block(s) in block group 30533 for inode bitmap: Could not allocate block in ext2 filesystem e2fsck: aborted Extra information I can give you: cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active (auto-read-only) raid5 sdg1[0] sdh1[5] sdf1[4] sde1[3] sdc1[2] sdd1[1] 7325679360 blocks level 5, 128k chunk, algorithm 2 [6/6] [UUUUUU] bitmap: 1/175 pages [4KB], 4096KB chunk unused devices: Lastly, all smartctl tests (short and extendend) showed no errors on any of the disks. Should I try to resize2fs to grow /dev/vg03/lv01 and redo a e2fsck ? Should I cfdisk /dev/md0 and /dev/vg03/lv01 back to their real types? Thanks in advance for all and any help. 2011-09-20 UPDATE I issued the following commands and was able to remount the partition, but by viewing the size (df) of before and after, it seems that 1Tb of data have gone missing. By checking the MD5SUMS (from an old backup) of some files with the "same" files from the remounted partition, some errors have been detected. Commands issued to remount the partition were: dumpe2fs /dev/vg03/lv01 Block count: 1000491435<br /> Block size: 4096<br /> tune2fs -O ^has_journal /dev/vg03/lv01 resize2fs -p /dev/vg03/lv01 dumpe2fs /dev/vg03/lv01 Block count: 1831418880<br /> Block size: 4096<br /> mount -o ro,noatime /dev/vg03/lv01 /mnt/raid OK... but files have been damaged / gone missing.

  Read the article

• Webapp in Jetty can't find properties file after running a couple days

  - by Cuga

  I have a webapp running in Jetty on Mac OS 10.6. After a few days of it running and without the server losing power or rebooting, it seems to stop working saying it can't find a properties file. This properties file is included inside the .war file deployed to the /webapps directory. If I restart Jetty as the superuser the web service works again just fine. Can anyone lend any advice to what's going on and how I can fix it? The error being shown when it isn't working is: Problem accessing /my-web-service. Reason: INTERNAL_SERVER_ERROR Caused by: java.lang.NullPointerException at com.company.service.Dao.readFromPropertiesFile(BwDao.java:35) at com.company.service.ServletHandler.doGet(ProxyClass.java:66) ... at org.mortbay.jetty.HttpConnection.handle(HttpConnection.java:404) at org.mortbay.io.nio.SelectChannelEndPoint.run(SelectChannelEndPoint.java:410) at org.mortbay.thread.QueuedThreadPool$PoolThread.run(QueuedThreadPool.java:582) Here's where the properties files exist that it's trying to read from the .war file: And this is how the properties are being read from the classpath: Properties properties = new Properties(); properties.load(Thread.currentThread().getContextClassLoader().getResourceAsStream( "app.properties")); Again, this does work just fine if I have just restarted the server, but it seems to fail after running a few days.

  Read the article

• Mac mini simple customized, Mac mini server or other?

  - by microspino

  I'm in front of a big IT choice for my little office and I need some advice. We have 5 users, 1 super user, 1 HP500 DesignJet Plotter, other 4 laser printers, 1 HP Fax/Print/Scan/Copy machine. All the clients are XP Sp3 boxes. We would like to: centralize and share 90Gb of files using a Dropbox (this way we will have LAN sync of local working directories + internet backup + access our files wherever we are). centralize our plotter, printers and fax machine backup all the workstations share outlook calendar and tasks run 24x7 saving some energy Of course this setup It's just the first step to a more serious and creative network management of our office, so we are open to new ideas. The budget vary from 400€ to 900€, we are not tech gurus but at least one of us is a power user close to become a geek. I've read some articles on macminicolo about a mac mini either normal or with snow leopard server. I heard about Windows Home Server too on the lifehacker website but I'm in a sort of analysis - paralysis can You help me?

  Read the article

• How should I perform database maintenance on a 24x7 system

  - by solublefish

  I'm a software developer who inherited a part-time DBA role. I'm responsible for an application backed by a small, high-volume 24x7 database on SQL Server 2008. While there's other stuff in the DB, the critical piece is a 50GB, 7.5M row table that serves 100K requests/sec during peak load, and about half that at "night". This is 99%+ read traffic, but the writes are constant, and required. I need to be able to perform periodic maintenance without a maintenance window. Say an index rebuild, a job to purge old data, Windows Update, or hardware upgrade. Most of the advice I've seen is along the lines of "MAKE a maintenance window." While I appreciate the sentiment, I hope there's another way. If it will solve this problem, I do have the ability to purchase new hardware or modify the database, the clients (a set of web services servers), and much of the application code (ADO.NET + ASP.NET). I've been thinking along the lines of using the warm spare (or a 3rd server) to do the maintenance, and then "swap" it into production. 1 Synchronize the spare by restoring backups, including a current transaction log. 2 Perform the maintenance tasks. 3 Reconfigure clients to connect to the spare server. Existing connections are finished within a minute or so. 4 The spare server is now the production server. The problem remaining is that the new production server is now out of date by however long it took to perform maintenance. Is there some way that the original production server can be made to queue up changes and merge them to the spare between steps 2 and 3? Any other ideas?

  Read the article

• How to bypass vpn talking to VMWare Guest?

  - by marc esher

  Greetings. Network/VPN n00b question here. I'm running VMWare Workstation with a Guest Windows 2003 Server. It has SQL Server 2000 installed. The sole purpose for this Guest is to house SQL Server... it needn't have internet access or access to any other resources on the network other than the host. When launch Check Point VPN software, the host routes through the company network before it connects to the guest ... i.e. it's no longer a direct connection. I assume this is just how things are supposed to work. However, what's happening is that the connection between my host and the SQL Server instance on the guest intermittently drops. It's not consistent, and some databases on the server will be responsive while others aren't. It appears that the databases with the most traffic on the guest (the ones I'm hitting with load tests) are the ones that become intermittently unresponsive. This problem only manifests when VPN is on; when it's off, I can pound away on this database with no troubles. Thanks for any advice!

  Read the article

• NTLM, Kerberos and F5 switch issues

  - by G33kKahuna

  I'm supporting an IIS based application that is scaled out into web and application servers. Both web and applications run behind IIS. The application is NTLM capable when IIS is configured to authenticate via Kerberos. It's been working so far without a glitch. Now, I'm trying to bring in 2 F5 switches, 1 in front of the web and another in front of the application servers. 2 F5 instances (say ips 185 & 186) are sitting on a LINUX host. F5 to F5 looks for a NAT IP (say ips 194, 195 and 196). Created a DNS entry for all IPs including NAT and ran a SETSPN command to register the IIS service account to be trusted at HTTP, HOST and domain level. With the Web F5 turned on and with eachweb server connecting to a cardinal app server, when the user connects to the Web F5 domain name, trust works and user authenticates without a problem. However, when app load balancer is turned on and web servers are pointed to the new F5 app domain name, user gets 401. IIS log shows no authenticated username and shows a 401 status. Wireshark does show negotiate ticket header passed into the system. Any ideas or suggestions are much appreciated. Please advice.

  Read the article

• How can I wipe my iPod classic and fix any bad sectors on the hard drive without killing it?

  - by Sam Meldrum

  My iPod never finishes syncing and only syncs audio, not pictures or video. Any ideas as to how I can fix it? My iPod classic 160GB worked well for a couple of years. I used to sync a lot of photos at full resolution to it, but this recently stopped working after I moved to Windows 7. iTunes is on latest version - 9.1.1.12 iPod software is up to date - 1.1.2 Windows 7 is fully up to date and patched The symptoms are that the iPod will start to sync, all audio (music and podcasts will sync successfully) but the syncing will then just appear to continue - itunes message: Syncing iPod. Do not Disconnect. This sync never completes - I have left it trying for days. I have tried resetting the iPod using the Restore button, whereupon it restarts sync from default options and again will sync audio, but nothing else. I suspect that something has gone wrong on the hard-drive - either a bad sector or some corrupt data. Is there a process I can go through to fix this? E.g. SpinRite or a format? If so how do I go about formatting an iPod and will it be recognised as an iPod after format and work as normal? Any advice on what to try next much appreciated? Update I have eliminated problems with the files, PC or iTunes as they sync fine to other iPods. I have also eliminated the cable by trying different cables which work with other iPods. What I'd really like to know is if there is any way to more fundamentally wipe the iPod safely, attempt to repair any bad sectors on the hard drive and then start from scratch. Anyone ever managed this?

  Read the article

• VirtualBox VM running web server not accessible via external IP

  - by mwigdahl

  I have a Windows 7 machine running VirtualBox with an Ubuntu guest. The guest has a Bitnami LAMP stack installed. I have the guest configured for Bridged networking, and I can access the guest web server just fine from other machines on my LAN using the guest's IP. I'm trying to configure port forwarding so that I can access the web server from outside my LAN. (The router is a 2WIRE model as I'm on ATT's UVerse). I've set up port forwarding for ports 80 and 443 to the guest's IP in a similar manner to how I had them set up for my previous, physical web server, which worked just fine. However, I cannot seem to access the new, virtual web server using my external IP on the forwarded port. I suspected Windows Firewall issues on the host, but disabling it didn't solve the issue. Anyone have advice on what I should try next? EDIT: I've now attempted disabling the firewall on the guest with sudo ufw disable -- that doesn't seem to help either. However, after checking the router's port forwarding in more detail I may see the problem. My VM is named "linux" and in the router's configuration pages it shows up inconsistently. Sometimes it reports with a valid LAN IP and other times it doesn't show up with any IP. Even when it shows the correct IP the router indicates that it is disconnected. Could this be an indication that the 2WIRE router doesn't play well with VirtualBox's bridged networking mode?

  Read the article

• nginx reverse proxy to apache mod_wsgi doesn't work

  - by user11243

  I'm trying to run a django site with apache mod-wsgi with nginx as the front-end to reverse proxy into apache. In my Apache ports.conf file: NameVirtualHost 192.168.0.1:7000 Listen 192.168.0.1:7000 <VirtualHost 192.168.0.1:7000> DocumentRoot /var/apps/example/ ServerName example.com WSGIDaemonProcess example WSGIProcessGroup example Alias /m/ /var/apps/example/forum/skins/ Alias /upfiles/ /var/apps/example/forum/upfiles/ <Directory /var/apps/example/forum/skins> Order deny,allow Allow from all </Directory> WSGIScriptAlias / /var/apps/example/django.wsgi </VirtualHost> In my nginx config: server { listen 80; server_name example.com; location / { include /usr/local/nginx/conf/proxy.conf; proxy_pass http://192.168.0.1:7000; proxy_redirect default; root /var/apps/example/forum/skins/; } #error_page 404 /404.html; # redirect server error pages to the static page /50x.html error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } } After restarting both apache and nginx, nothing works, example.com simply hangs or serves index.html in my /var/www/ folder. I'd appreciate any advice to point me in the right direction. I've tried several tutorials online to no avail.

  Read the article

• What is the main reason of adsl modem/routers dying ?

  - by ldigas

  The other day my home adsl modem/router (dwg 684t in this case) died. A guy from the telecom company came, brought another so no problem in day to day operation, but he also left this one. Now, I'm interested ... it didn't fall, it wasn't electrocuted ... but it just doesn't work. What could be the problem ? Can they be fixed ? Is it worth it (in which case I would have two which is always nice) ... What are the usual problems that occur with them ? In this case, I can connect to the router, I can see its settings, I just can't connect to the internet. With the new one everything works. Weird. Edit: Additional question: Can those things be fixed ? I mean, is it worth giving it to a local tinker for him to experiment on it ? I'm not looking for a definite opinion, just your personal advice ... (although in the end I think I'm gonna archive it in the "cylinder register")

  Read the article

• Using URL rewrite module for http to https redirect

  - by johnnyb10

  Following ruslany's suggestion on the URL Rewrite Tips page here, I'm trying to use URL Rewrite to redirect http:// requests for my site to https://. I've written and tested the rule using a test site I set up, and so now the final piece is to create a second site (http) to redirect to my https site. (I need to use a second site because I don't want to uncheck the "Require SSL encryption" checkbox on my existing site.) I'm an IIS newbie so my question is: how do I do this? Should I create a site with the same name and host header, only it will be bound to http? Will IIS let me create a site with the same name? I don't want to screw anything up with my existing site (which is a SharePoint site, currently used by external users). That site currently has http and https bound to it. So my assumption is that, using ISS (not SharePoint), I will create a new site (http only) with the same name and host header as my existing site, and add the URL Rewrite rule to the http site. And then I guess I should remove the http binding from my existing site? Does that seem correct? Any advice, gotchas, etc., would be appreciated. Thanks.

  Read the article

• Monitoring AWS Systems Behind ElasticBeanStalk

  - by A. Avadis

  So I'm getting a company set up in the Amazon Cloud -- creating IAAS protocol/solutions/standardized implementation, etc while also being the SysAdmin for individual systems, app environments, and day-to-day uptime. One of the biggest issues I'm having is tracking various system/application logs, as well as logging/monitoring/archiving system metrics like memory usage, cpu usage, etc etc In a centralized fashion. E.g. -- Nagios + Urchin. The BIGGEST impediment to my endeavors is the following: The company application is deployed in the form of a Java *.WAR file, uploaded to an Elastic BeanStalk application environment, load balancing and auto-scaling between 3(min) and 10(max) servers, and the EC2's that run the application are fired up and disposed of ad-hoc. That is to say, I can't monitor the individual EC2's for very long because so many are being terminated then auto-provisioned/auto-scaled on the fly -- so I'd constantly be having to "monitor what I'm monitoring", and continuously remove/add EC2 machine addresses to my monitoring lists. IS there some sort of way to use monitoring tools like Zabbix or Nagios to monitor the ElasticBeanStalk, and have it automatically add on new EC2's, and remove terminated/failed EC2's from its monitoring list automatically? Furthermore, is there anything I can do with GrayLog to achieve similar results with the aggregation/centralization of my application logs from multiple EC2 instances into ONE consolidated set of logs/events? If not GrayLog, is there ANYTHING LIKE GrayLog that can automatically detect what EC2 members are being added/removed from the environment, and collect the logs from them automatically? Any and all advice or direction is appreciated. Thanks much, and cheers!!

  Read the article

• Windows Server 2012 Hyper-V very slow

  - by Matt Taylor

  I have been running several Hyper-V VMs on Windows Server 2008 R2 for the past couple of years and enjoying perfectly adequate performance for my testing/development/r&d environments. I'm a software developer so my hardware knowledge is basic however I built the rig using: •Gigabyte GA-X58A-UD3R Intel X58 (Socket 1366) DDR3 Motherboard •Intel Core i7 960 3.20GHz (Bloomfield) (Socket LGA1366) •24GB triple channel RAM The host OS is running on an OCZ SSD and all the VMs are running on a 2TB Marvell SATA3 RAID 0 array consisting of 2 Western Digital Caviar Black 7,200rpm drives. I have tested the speed of the 2TB drive and appear to be getting less than 3Mbs but it can adequately run a 4 VM farm including a DC, (SQL) database and IIS application servers. I recently upgraded the SSD on which the host runs to a 256GB OCZ Vertex 4 and took the opportunity to upgrade to Windows Server 2012 and installed the Hyper-V role. I tried importing one of my existing Windows Server 2008 R2 VMs (and converted it to .vhdx) plus I have tried creating a brand new Windows Server 2008 R2 VM but both are running extremely slowly and I can see nothing obvious using the host and guest Task Manager/Resource Monitor tools. In both cases the VM has 8GB RAM (fixed), 4 CPUs, fixed size HD (not expanding) and is using an external virtual network running on a separate NIC to the host. I have upgraded the BIOS to the latest available version and checked the virtualization settings. I have run out of "obvious" (to a developer) things to check/configure and my next option will be to re-install the host OS but before I do I would very much appreciate any advice from any experts out there. Thanks

  Read the article

< Previous Page | 450 451 452 453 454 455 456 457 458 459 460 461  | Next Page >