Search Results

Search found 7992 results on 320 pages for 'hp power protector'.

Page 46/320 | < Previous Page | 42 43 44 45 46 47 48 49 50 51 52 53  | Next Page >

• Proliant server will not accept new hard disks in RAID 1+0?

  - by Leigh

  I have a HP ProLiant DL380 G5, I have two logical drives configured with RAID. I have one logical drive RAID 1+0 with two 72 gb 10k sas 1 port spare no 376597-001. I had one hard disk fail and ordered a replacement. The configuration utility showed error and would not rebuild the RAID. I presumed a hard disk fault and ordered a replacement again. In the mean time I put the original failed disk back in the server and this started rebuilding. Currently shows ok status however in the log I can see hardware errors. The new disk has come and I again have the same problem of not accepting the hard disk. I have updated the P400 controller with the latest firmware 7.24 , but still no luck. The only difference I can see is the original drive has firmware 0103 (same as the RAID drive) and the new one has HPD2. Any advice would be appreciated. Thanks in advance Logs from server ctrl all show config Smart Array P400 in Slot 1 (sn: PAFGK0P9VWO0UQ) array A (SAS, Unused Space: 0 MB) logicaldrive 1 (68.5 GB, RAID 1, Interim Recovery Mode) physicaldrive 2I:1:1 (port 2I:box 1:bay 1, SAS, 73.5 GB, OK) physicaldrive 2I:1:2 (port 2I:box 1:bay 2, SAS, 72 GB, Failed array B (SAS, Unused Space: 0 MB) logicaldrive 2 (558.7 GB, RAID 5, OK) physicaldrive 1I:1:5 (port 1I:box 1:bay 5, SAS, 300 GB, OK) physicaldrive 2I:1:3 (port 2I:box 1:bay 3, SAS, 300 GB, OK) physicaldrive 2I:1:4 (port 2I:box 1:bay 4, SAS, 300 GB, OK) ctrl all show config detail Smart Array P400 in Slot 1 Bus Interface: PCI Slot: 1 Serial Number: PAFGK0P9VWO0UQ Cache Serial Number: PA82C0J9VWL8I7 RAID 6 (ADG) Status: Disabled Controller Status: OK Hardware Revision: E Firmware Version: 7.24 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: True Cache Status: OK Cache Status Details: A cache error was detected. Run more information. Cache Ratio: 100% Read / 0% Write Drive Write Cache: Disabled Total Cache Size: 256 MB Total Cache Memory Available: 208 MB No-Battery Write Cache: Disabled Battery/Capacitor Count: 0 SATA NCQ Supported: True Array: A Interface Type: SAS Unused Space: 0 MB Status: Failed Physical Drive Array Type: Data One of the drives on this array have failed or has Logical Drive: 1 Size: 68.5 GB Fault Tolerance: RAID 1 Heads: 255 Sectors Per Track: 32 Cylinders: 17594 Strip Size: 128 KB Full Stripe Size: 128 KB Status: Interim Recovery Mode Caching: Enabled Unique Identifier: 600508B10010503956574F305551 Disk Name: \\.\PhysicalDrive0 Mount Points: C:\ 68.5 GB Logical Drive Label: A0100539PAFGK0P9VWO0UQ0E93 Mirror Group 0: physicaldrive 2I:1:2 (port 2I:box 1:bay 2, S Mirror Group 1: physicaldrive 2I:1:1 (port 2I:box 1:bay 1, S Drive Type: Data physicaldrive 2I:1:1 Port: 2I Box: 1 Bay: 1 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 73.5 GB Rotational Speed: 10000 Firmware Revision: 0103 Serial Number: B379P8C006RK Model: HP DG072A9B7 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:2 Port: 2I Box: 1 Bay: 2 Status: Failed Drive Type: Data Drive Interface Type: SAS Size: 72 GB Rotational Speed: 15000 Firmware Revision: HPD9 Serial Number: D5A1PCA04SL01244 Model: HP EH0072FARUA PHY Count: 2 PHY Transfer Rate: Unknown, Unknown Array: B Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data Logical Drive: 2 Size: 558.7 GB Fault Tolerance: RAID 5 Heads: 255 Sectors Per Track: 32 Cylinders: 65535 Strip Size: 64 KB Full Stripe Size: 128 KB Status: OK Caching: Enabled Parity Initialization Status: Initialization Co Unique Identifier: 600508B10010503956574F305551 Disk Name: \\.\PhysicalDrive1 Mount Points: E:\ 558.7 GB Logical Drive Label: AF14FD12PAFGK0P9VWO0UQD007 Drive Type: Data physicaldrive 1I:1:5 Port: 1I Box: 1 Bay: 5 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE07QH300009923X1X3 Model: HP DG0300BALVP Current Temperature (C): 32 Maximum Temperature (C): 45 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:3 Port: 2I Box: 1 Bay: 3 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE0AHVH00009924P8F3 Model: HP DG0300BALVP Current Temperature (C): 34 Maximum Temperature (C): 47 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:4 Port: 2I Box: 1 Bay: 4 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE08NAK00009924KWD6 Model: HP DG0300BALVP Current Temperature (C): 35 Maximum Temperature (C): 47 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown

  Read the article

• HP DL160G6 bios update fails

  - by Bojo

  I tried to update the BIOS from my HP DL160G6's. Unfortunately the Windows update degraded my BIOS version from 243 to 237. But when I try to upgrade both servers to version the update fails. First I got a warning like: CMOS Layout difference between System ROM and ROM file has detected. AFU recommand (sic) adding /C commands of your original input commands. Press "A" to accept AFU's recommendation. Press "F" to keep original input commands. And the update did not do anything. But now I get a message like: Reading flash ........ done Bootblock checksum ... ok Module checksums ..... bad Error: BIOS checksum error And the update stops. I tried some commands form this page: http://www.ami.com/support/downloads/txt/AFU_README.TXT But I don't try to much, the servers are still booting. Does anyone know how to update my servers to BIOS version 245? I used this version http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=3884344&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253DMTX_7bd12651ab954fdcb0d7ee164a%257CswEnvOID%253D54%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken and created a bootable USB stick sith HPQUSB.exe

  Read the article

• HP Storageworks 448 tape drive input/output error with Ubuntu

  - by Dan D

  I'm trying to set a backup to tape of a machine using flexbackup. However any attempt to write to the tape drive (via either flexbackup or just tar) results in "/dev/st0: Input/output error" The machine seems to recognise the drive (HP Storageworks Ultrium 448) and that there's a tape in it and "mt status" seems to work... "mt -f /dev/st0 rewind" or "erase" throw no errors... root@stor001:/# mt status SCSI 2 tape drive: File number=0, block number=0, partition=0. Tape block size 0 bytes. Density code 0x42 (LTO-2). Soft error count since last status=0 General status bits on (41010000): BOT ONLINE IM_REP_EN root@stor001:/# cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: DVDRAM GSA-4084N Rev: KS02 Type: CD-ROM ANSI SCSI revision: 05 Host: scsi2 Channel: 00 Id: 03 Lun: 00 Vendor: HP Model: Ultrium 2-SCSI Rev: S65D Type: Sequential-Access ANSI SCSI revision: 03 "tell" does however root@stor001:/# mt -f /dev/st0 tell /dev/st0: Input/output error Based on a forum post I found, I tried: root@stor001:/# dd if=/dev/zero of=/dev/nst0 bs=1024 count=10 10+0 records in 10+0 records out 10240 bytes (10 kB) copied, 5.0815 s, 2.0 kB/s which gave the person on the forum an error but seems to work for me. If anyone has any suggestions, I'm all ears...

  Read the article

• Red Hat 5.3 on HP Proliant DL380 G5 and failed drive on RAID controller

  - by thinkdreams

  I have a development ERP server here in my office that I assist with support on, and originally the DBA requested a single drive setup for some of the drives on the server. Thus the hardware RAID controller (an HP embedded controller) looks like: c0d0 (2 drive) RAID-1 c0d1 (2 drive) RAID-1 c0d2 (1 drive) No RAID <-- Failed c0d3 (1 drive) No RAID c0d4 (1 drive) No RAID c0d5 (1 drive) No RAID c0d2 has failed. I replaced the drive immediately with a spare using the hot-swap, but the c0d2 continues to mark itself as failed, even when I umount the partition. I'm loathe to reboot the server since I'm concerned about the server coming back up in rescue mode but I'm afraid that's the only way to get the system to re-read the drive. I assumed there was some sort of auto-detection routine for this, but I haven't been able to figure out the proper procedure. I have installed the HP ACU CLI utilties, so I can see the hardware RAID setup. I'd really like to find out what the proper procedure should have been, where I went wrong, and how to correct it now. Obviously this goes without saying I should NOT have listened to the DBA and set the drives up as RAID-1 throughout as was my first instinct. He wasn't worried about data loss, but it sure would have been easier to replace the failed drive. :)

  Read the article

• Intel DriverInstall issue on HP ProLiant server DL580G5

  - by TomTom

  Given: A HP ProLiant server to be used for Hyper-V server (R 2) Problem: The server has a HP NC364T quad port card, which actually is an Intel 1000 Pro adapter. We are stuck getting this adapter properly working. We need to get it working with: 2 trunks of 2 ports each one of them fully vlan "aware" (without filtering anything - so that Hyper-V can do the VLAN filtering). So far we did: Install the server Install latest PSP. Problem here - tool does not work to set up teaming. We tried to install the latest ProWin pack from Intel - the drivers there are a LOT more current (26th of Marrch 2010, 9.13.41.0). The intalled driver (Microsoft) is ancient (march 2009, 9.13.4.10) A driver update fails both on command line (pnputil) as well as the PortLock device manager executable. No informatoin is provided. the ANS toolset can not create teams (fails with error - again, no reason provided), I know of no logs and the event log has no information either. Questions: What are the best drivers to use? How do we actually install them? How can we then set up teaming and how do we set up the VLAN behavior wanted?

  Read the article

• HP Officejet 4500 G510n-z Not Showing up in Remote Desktop (Terminal Services)

  - by Greg_the_Ant

  I installed this printer on a windows XP machine. First using the wireless option, and later using USB. In both cases when I connect to my other computer (also Windows XP) via terminal services and check printers in the local resources tab it does not show up on the remote session. I used to have a Samsung connected to my local computer over USB and and that worked fine over terminal services. Things I tried so far: I did read this page and installed the software fix on both computers: (Printers that use ports that do not begin with...) I installed the minimum HP software install on the remote computer and that didn't help either. I also tried running the add new printer wizard on the remote computer: I selected "local printer attached to this computer" and did not check the "automatically.." option. On the next page of the wizard I can select an option for "use the following port". I see options for TS001 through TS009 there. I'm assuming those are coming from the local machine. I tried clicking each one and then checking "have disk" and pointing it to C:\3be8dc611b11322e8ddf8a67\i386\msxpsdrv.inf 1 but for every single TS00.. port it says "The specified location does not contain information about your hardware." Any help would be greatly appreciated. I'm pretty stuck at this point. 1 C:\3be8dc611b11322e8ddf8a67 is the folder I extracted the HP driver software to after I downloaded it.

  Read the article

• Windows XP - Power surge on hub port

  - by Swift-Tuttle

  Since last few weeks I constantly get this error, as status bar balloon: Power Surge on Hub Port - A USB device has exceeded the power limits of its hub port. Due to this now I am unable to access any USB devices properly, they get disconnected intermittently. I did quite a few things to resolve this problem, firstly obviously through the Windows help. I even tried all the things told on the Microsoft website(which essentially says is to check and update the driver) but in vain. One suggestion, I found when I google'd was to disable the USB2 controller through the Device Manager and since at every startup the System configuration comes up complaining that it has been changed etc.(On that same site it is mentioned to ignore this message.) But after everything I still cant solve this problem. Any help is much appreciated. The system is installed with Windows XP service Pack 3 and all the updates till last month. Please let me know if any other hardware info is required. **UPDATE** My laptop is about 5 years old now, its an HP with Celeron 1.4G processor. Windows XP SP3 installed. All latest windows updates installed. 2 USB ports available. BIOS is HP 68DTD ver F.0A Do I need to update my BIOS from somewhere ? or is this a hardware problem altogether?

  Read the article

• Cannot find wireless driver for HP laptop

  - by rodey

  I have an HP laptop (model: dv7-1267cl, Windows 7 64-bit Home Premium) and I cannot find the wireless driver for the laptop. I am need of a different version because my wireless connection under Windows is flaky and unreliable. I have problems printing to my wireless printer and logging in to and using several sites like reddit.com, phoenix.edu and facebook.com - I get several "page cannot be displayed" messages while using my wireless connection. I disable my wireless adapter and use an ethernet cable and it all works fine. I also used an Ubuntu Live CD to confirm that there is not a problem with the hardware. This is software/driver issue. The drivers were auto installed by the OS. The Device Manager shows the wireless adapter as Atheros AR5009 802.11 a/g/n WiFi Adapter. I have checked the HP website for my laptop and they do not have wireless drivers listed for that model wireless adapter. I have also checked with atheros.com and I do not see my model adapter on their list of available hardware. Device Manager lists the Hardware ID's for my adapter as: PCI\VEN_168C&DEV_002A&SUBSYS_1381103C&REV_01 PCI\VEN_168C&DEV_002A&SUBSYS_1381103C PCI\VEN_168C&DEV_002A&CC_028000 PCI\VEN_168C&DEV_002A&CC_0280 A search for the first Hardware ID turned up this question from experts-exchange.com. tl;dr A driver does not exist for that model adapter.

  Read the article

• How do you make this Haskell power function tail recursive?

  - by Linda Cohen

  turboPower a 0 = 1 turboPower a b | even b = turboPower (a*a) (b `div` 2) | otherwise = a * turboPower a (b-1) THANKS!

  Read the article

• HP Laptop recognizes hard drive just long enough to install windows

  - by Joe

  I have an HP laptop, DV6500 (CTO). It refused to boot one day, so I ran some diagnostics (a friend lent me "Hirens Boot Disk", "UBCD" and "PC DR 6"). Everything passed, except for the hdd. I replaced the HDD with a used drive of unknown condition. Installed windows with no problems. Installed the wireless driver, tried to reboot ... no luck. So I went to Best Buy, bought a brand new Western Digital 320gb HDD. Put it in the machine, installed windows (vista home premium). Installed the wired networking driver. Tried to reboot. No luck. Put the first hdd back in the machine, reinstalled windows. Started to install some drivers, went to reboot, and the machine won't come back to life. Put the second hdd in the machine, rinse wash and repeat. I've replaced the memory, even though it passed diagnostics. Problem exists with both brand new memory, and old memory. The BIOS recognizes the hard drive. The computer freezes directly after the bios splash screen, and there is no hard drive activity light. I've tried two linux live distros (gentoo and ubuntu). Neither would run on this laptop, but will on a different HP laptop. UBCD and Hirens Boot Disk both ran, as did PC Doctor 6 which refuses to test anything (gets stuck at "enumerating hard disks"). Is there anything else I can try?

  Read the article

• Windows XP - Power surge on hub port

  - by Swift-Tuttle

  Hi, Since last few weeks I constantly get this error, as status bar balloon: Power Surge on Hub Port - A USB device has exceeded the power limits of its hub port. Due to this now I am unable to access any USB devices properly, they get disconnected intermittently. I did quite a few things to resolve this problem, firstly obviously through the Windows help. I even tried all the things told on the Microsoft website(which essentially says is to check and update the driver) but in vain. One suggestion, I found when I google'd was to disable the USB2 controller through the Device Manager and since at every startup the System configuration comes up complaining that it has been changed etc.(On that same site it is mentioned to ignore this message.) But after everything I still cant solve this problem. Any help is much appreciated. The system is installed with Windows XP service Pack 3 and all the updates till last month. Please let me know if any other hardware info is required. **UPDATE** My laptop is about 5 years old now, its an HP with Celeron 1.4G processor. Windows XP SP3 installed. All latest windows updates installed. 2 USB ports available. BIOS is HP 68DTD ver F.0A Do I need to update my BIOS from somewhere ? or is this a hardware problem altogether?

  Read the article

• What do people mean when they say 'the power of C++'?

  - by Bubba88

  I've heard many times that it is a 'flexible and very powerfull' language, but in what aspect could this be applied to C++?

  Read the article

• Intel HD graphic drivers for ubuntu 10.10 64bit: the brightness says its being adjusted but it isn't

  - by James

  Hey all, I picked up an hp dm3t laptop with intel HD graphics and installed ubuntu 10.10 64 bit on it. It works great -- the only problem is that the brightness controls on the keyboard don't work. The brightness is always at full. When I try to adjust it down, the indicator graphic indicates that it's going down but the actual brightness doesn't change. Is there anything that I can try to make this work? I'd really appreciate any help. I asked this on superuser.com and someone commented that I should play around with the intel hd drivers. I'm a total noob -- how do I do that? What else can I try? I reallly don't want to do back to windows.

  Read the article

• 13.10 hangs on waking from suspend except when suspended from console

  - by Pavel

  I know waking from suspend is an issue, but this looks like a separate bug. When I suspend 13.10 on HP Pavillion dv6 (AMD 6770M/fglrx 13.10.10) from x, it suspends normally but freezes when waking. I get a black screen with a frozen cursor. But when I suspend from console with sudo pm-suspend, it wakes normally, and I can then get back my x with ctrl-alt-f7. If I suspend by closing lid under x, also freezes when waking up. If I suspend by closing lid under console, it wakes up into the x (?) login, then into a clean session.

  Read the article

• installing my Graphic Card on ubuntu12.04

  - by lamouchi amine

  I have a HP Pavillion G6 series 1225, i5 laptop with Radeon HD 6470M switchable VGA. i installed Ubuntu 12.04 LTS but the VGA drivers don't work properly. I want to install drivers into the Ubuntu. But when I do it arrived error message like this: sorry, installation of this driver failed. Please have a look at the log file for details: /var/log/jockey.log I found a solution in a link: http://ubuntuforums.org/showthread.php?t=1930450 It works for a few steps and then in the installation of the package of the AMD driver, a message pops up 'fatal error' and it redirects me to Ask Ubuntu to find a solution, please help me, I need to make it work.

  Read the article

• files power_profile and power_method missing on ubuntu 12.04 after clean isntall

  - by Nikola

  OK here is the problem,I am using gnome-shell, ubuntu 12.04, kernel 3.2.0-32-generic-pae and the proprietary drivers for my ati card (Installed via "additional drivers") , the laptops is a hp 4310s probook and i want to control the power_profiles and power_method , because my GPU temp is high. before i reinstalled ubuntu 12.04, i used the .sh method on startup to write to those files, and everything worked like a charm, but now they are missing, and i can't create them.this is what i get when i try to create the directories mkdir: cannot create directory `/sys/class/drm': No such file or directory How can i can get them back?if you need some information , just ask and i will give it.

  Read the article

• Realtek 8188ce stops working after 2minutes

  - by Max M

  I am using ubuntu 12.10 on an hp dm4-2191us via wubi with the Realtek 8188ce wifi adapter. Everything works very well with the exception of the wifi. I have used wicd and it didn't worked at all so i went back to Network Manager with variable success. It works for 30 min - 2 min before i have to reconnect to get it to work again. I would really like to use Ubuntu (it is a better platform in my opinion) but no wifi could really be a deal breaker.

  Read the article

• Broken package ubuntuone-control-panel-qt

  - by baale7

  An interrupted installation of updates resulted in ubuntuone-control-panel-qt breaking and now I cannot install or update anything. There seems to be an error in python2.7 - ImportError: No module named _sysconfigdata_nd dpkg: error processing archive ubuntuone-control-panel-qt_13.09-0ubuntu1_all.deb (--install): When I try to reinstall the package via .deb a dpkg --audit yields: The following packages are in a mess due to serious problems during installation. They must be reinstalled for them (and any packages that depend on them) to function properly: ?python-pexpect Python module for automating interactive applications ?ubuntuone-control-panel-qt Ubuntu One Control Panel - Qt frontend ?hplip-data HP Linux Printing and Imaging - data files ?python-libxml2 Python bindings for the GNOME XML library ?apport automatically generate crash reports for debugging The following packages are only half configured, probably due to problems configuring them the first time. The configuration should be retried using dpkg --configure or the configure menu option in dselect: ?python-ubuntuone-client Ubuntu One client Python libraries ?python-ubuntuone-control-panel Ubuntu One Control Panel - Python Libraries --configure or --configure -a doesn't work Any help?

  Read the article

• My Laptop Battery Does Not Charge

  - by Oo Nwoye

  I am using a HP Pavilion and Ubuntu 11.10. I have been using Ubuntu for about a year. Recently (in Nov or there about), I noticed my battery never charges fully no matter how long it has been plugged in. I thought it was a problem with the power pack. However, after changing it, the problem is still persisting. I upgraded to 11.10 form 11.04 at about the same time so I do not know if this is a software or hardware issue. How do I solve this? This problem has been written about in various forms Laptop battery not charging after update?. Please help me or find someone that can.

  Read the article

• I cannot change the screen brightness

  - by user1793249

  here's my problem: Ever since I installed Ubuntu 12.10 on my computer I haven't been able to change the screen brightness, it was always set to the maximum. I did take a look at this post: Decrease Backlight Below Minimum And it helped me resolved the issue with the unbearable brightness, however one problem persists: I cannot change it through "Brightness & Lock" or the function buttons (F2 and F3), when I press the buttons, the animation shows up but nothing happens. I tried the following: http://www.refreshit.info/2012/08/solved-brightness-increase-and-decrease.html It did nothing... If it helps: I have an HP-dv6 6185la, it has an ATI Radeon 6770M HD card and an Intel HD Integrated Graphics Card It only detects the "Intel® Sandybridge Mobile" Thanks in advance.

  Read the article

• Can't install Ubuntu 13.10 from 12.04 lts

  - by Matt Carle

  I have ubuntu 12.04 lts installed on my hp pavilion and I want to try 13.10. When I try to boot into the livecd, I get the purple ubuntu splash screen, then a blackscreen where some text flashes (to fast to see what it says) then it goes to a black screen and stays there. I know the installation disc is not the problem because I've successfully installed it on a different machine using the same disc. I've been trying to troubleshoot the issue for a while now and no luck. I have a radeon hd 8250 card. I know it's not much to go off of but any help would be greatly appreciated! Thanks!

  Read the article

• I can not print on Windows 7 shared printer

  - by lrichard

  For a while I can not print from my Ubuntu 12.04 64 bit pc on a Windows 7 shared printer. Before that everything was ok. The printer is HP LaserJet 1100. The error message is: "File "/usr/lib/cups/backend/smb" not available: No such file or directory" I have tried to reinstall the samba, I have configured the workgroup properly. I have tried to reinstall the printer on the Ubuntu machine with the proper address, or with lpd (I have read somewhere). If I restart the printer on the cups web interface ("Resume Printer") the problem seems to be solved, but not. (The printer seems to be idle, and if I want to print, I still get the error message.) I have checked the share rights on the Windows 7 pc, and I think it is ok.

  Read the article

• Add Network Printer drivers in Windows 7/Server 2008 R2?

  - by Matias Nino

  I'm running a 64 bit Windows 7 / Windows 2008 R2 workstation that I just installed. I need to add a printer that is shared on the network from a 32bit Windows 2000 print server. This is an HP LaserJet 5Si printer, the drivers for which HP tells me are automatically built into Windows 7/R2. However, whenever I connect to the printer or try to add it, I get the following screen: Upon clicking OK, I get this screen asking me to locate the driver: How can I possibly locate a driver that is SUPPOSED TO BE NATIVELY SUPPORTED on Windows 7/R2? The tough part is that this printer is one of many shared on a server and does not have a direct IP address. Even worse: I have no access to the print server so I cannot put the 64 bit drivers on there. Any ideas? UPDATE: HP doesn't make a Vista driver either. It claims it is natively supported by Vista and 7, which is true because I am able to create a local printer on a fake tcp/ip port and Windows lets me pick the proper driver. However, when adding from the network, Windows does not let me select a driver and demands an INF. I tried searching the entire sub-structure of the C:\Windows directory and could not find any INF files that contain HP information. The INF might be located somewhere in the Windows installation DVD, but all the files on the DVD are compressed and unrecognizable. UPDATE #2 I installed the proper printer driver as a local printer (with no printer attached) and it installed. However, this did not change the fact that it STILL asks me to provide drivers when connecting to the networked printer.

  Read the article

• Linux - real-world hardware RAID controller tuning (scsi and cciss)

  - by ewwhite

  Most of the Linux systems I manage feature hardware RAID controllers (mostly HP Smart Array). They're all running RHEL or CentOS. I'm looking for real-world tunables to help optimize performance for setups that incorporate hardware RAID controllers with SAS disks (Smart Array, Perc, LSI, etc.) and battery-backed or flash-backed cache. Assume RAID 1+0 and multiple spindles (4+ disks). I spend a considerable amount of time tuning Linux network settings for low-latency and financial trading applications. But many of those options are well-documented (changing send/receive buffers, modifying TCP window settings, etc.). What are engineers doing on the storage side? Historically, I've made changes to the I/O scheduling elevator, recently opting for the deadline and noop schedulers to improve performance within my applications. As RHEL versions have progressed, I've also noticed that the compiled-in defaults for SCSI and CCISS block devices have changed as well. This has had an impact on the recommended storage subsystem settings over time. However, it's been awhile since I've seen any clear recommendations. And I know that the OS defaults aren't optimal. For example, it seems that the default read-ahead buffer of 128kb is extremely small for a deployment on server-class hardware. The following articles explore the performance impact of changing read-ahead cache and nr_requests values on the block queues. http://zackreed.me/articles/54-hp-smart-array-p410-controller-tuning http://www.overclock.net/t/515068/tuning-a-hp-smart-array-p400-with-linux-why-tuning-really-matters http://yoshinorimatsunobu.blogspot.com/2009/04/linux-io-scheduler-queue-size-and.html For example, these are suggested changes for an HP Smart Array RAID controller: echo "noop" > /sys/block/cciss\!c0d0/queue/scheduler blockdev --setra 65536 /dev/cciss/c0d0 echo 512 > /sys/block/cciss\!c0d0/queue/nr_requests echo 2048 > /sys/block/cciss\!c0d0/queue/read_ahead_kb What else can be reliably tuned to improve storage performance? I'm specifically looking for sysctl and sysfs options in production scenarios.

  Read the article

• Why does Ubuntu (and other ubuntu based distros like lubuntu and linux mint) randomly shutdown on my laptop?

  - by Imran

  I have a lenovo g555 laptop and whenever I try and boot a ubuntu based distro off a usb, it randomly shuts off my PC (Not like a normal shutdown with shutdown loading screen but a like a sudden hard power off). This problem occurs even if I have installed the distro on my harddrive. In the past I've been able to use the distro for 10 min or so before it would it would do this. Now with the latest distros, It randomly pwers off even before it has fully booted up. My hardware specs are on this website.

  Read the article

< Previous Page | 42 43 44 45 46 47 48 49 50 51 52 53  | Next Page >