Search Results

Search found 12281 results on 492 pages for 'ip blocking'.

Page 46/492 | < Previous Page | 42 43 44 45 46 47 48 49 50 51 52 53  | Next Page >

  • blocking port 80 via iptables

    - by JoyIan Yee-Hernandez
    I'm having problems with iptables. I am trying to block port 80 from the outside, basically plan is we just need to Tunnel via SSH then we can get on the GUI etc. on a server I have this in my rule: Chain OUTPUT (policy ACCEPT 28145 packets, 14M bytes) pkts bytes target prot opt in out source destination 0 0 DROP tcp -- * eth1 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 state NEW,ESTABLISHED And Chain INPUT (policy DROP 41 packets, 6041 bytes) 0 0 DROP tcp -- eth1 * 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 state NEW,ESTABLISHED Any guys wanna share some insights?

    Read the article

  • Static IP addressing issue in Ubuntu on BeagleBoneBlack Rev C

    - by Stringfellow
    I have my BBB configured to use a static IP address using the following in the file /etc/network/interfaces: allow-hotplug eth0 iface eth0 inet static address 192.168.0.1 netmask 255.255.255.0 network 192.168.0.0 This seems to work ok on boot, but when the ethernet cable is unplugged and then plugged back in, I lose the IP address. Any ideas what's going on here? Another weird symptom: If I boot the BBB with the network cable unplugged, but the switch it's plugged into off, I'll get my static IP. But, when I turn the switch on, I'll get a DHCP-assigned address. This is even though I have it configured with a static IP address. One last thing. If I ifdown etho, the interface will be gone when I do an ifconfig. If I wait a few seconds, though, and then re-run ifconfig, it will reappear, without an IP address. (Before I disabled IPv6, I used to get a IPv4 DHCP address in this case... weird). When that happens, I get a message like this in /var/log/messages: Apr 23 20:32:06 beaglebone kernel: [ 737.170172] libphy: 4a101000.mdio:00 - Link is Up - 100/Full Apr 23 20:32:06 beaglebone kernel: [ 737.170304] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Here's my uname -a: root@beaglebone:/etc# uname -a Linux beaglebone 3.8.13-bone47 #1 SMP Fri Apr 11 01:36:09 UTC 2014 armv7l GNU/Linux Any ideas what's going on here?

    Read the article

  • Send email from different domains to different external IP's on a single server

    - by user140429
    I have set up a windows 2008 R2 server to route email from Exchange 2010 using SMTP Server in IIS. I have 3 seperate domains and would like to route each one through a different internal and external IP for (IP Reputation etc), at the minute it is only using the primary IP on the server to route email externally. Is this at all possible using SMTP Server in IIS, or is there any other software available to do this?

    Read the article

  • Samba deny host not blocking that host

    - by datadevil
    I want to block access to some Samba shares from a certain machine, but somehow I can't get it to work: the machine can still access the shares, and I did restart and reload the samba daemon. Here is a part of my configuration: security = share hosts allow = 127.0.0.1 192.168.1.0/24 interfaces = 127.0.0.1 eth1 192.168.1.2 bind interfaces only = yes hosts deny = 192.168.1.251 encrypt passwords = yes guest ok = yes The shares themselves look like this: [examples] comment = Example path = /foo/bar read only = No guest ok = yes What am I doing wrong here?

    Read the article

  • debian lenny : problem modifying static ip

    - by supertiti
    hello all, i'm trying to change a static ip assigned to a debian VM. I modified the /etc/network/interfaces file but my debian doesn't seem to like the new settings currently the machine's ip is set to 192.168.1.136 and i want the machine's ip to be set to 192.168.1.8 here's my modified /etc/network/interfaces : auto lo iface lo inet loopback allow-hotplug eth0 auto eth0 iface eth0 inet static address 192.168.1.8 gateway 192.168.1.1 netmask 255.255.255.0

    Read the article

  • Mac | Router not assigning the IP address.

    - by Vaibhav Bajpai
    I recently installed Mac OS X 10.6, however the ethernet state is down. The assigned IP is 169.x.x.x. When booted the live USB of Ubuntu, I properly get an IP assigned in the range 192.168.1.x from the router 192.168.1.1 I am using the same router and same ethernet line. I tried to ping to 192.168.1.1 from my Mac and I get a host down message. I tried to manually assign the IP and set the router IP to 192.168.1.1 but still the router is unreachable.

    Read the article

  • Configure Virtualbox guest with static IP, SSH and internet access from host

    - by koskoz
    I have an Ubuntu Server 12 virtualbox guest running on a Windows 7 host which has a dynamic IP (and I don't wanna change this considering it's a laptop and I'm changing network frenquently). I want to have a static IP for my VM and a SSH access from my host but I still want to have the internet access on my VM. I tried added a second host only adapter and configured /etc/network/interface to set eth1 to a static ip, but I can't connect via SSH to it. Setting only adapter1 to host only works for SSH and static IP but I lose the internet access.

    Read the article

  • Firewall is blocking internet traffic to OpenVPN clients

    - by user268905
    I have a virtual network setup with a Linux router/firewall connected to two private networks. An OpenVPN server in routing mode and a web server are in one of the networks. On the other are linux client machines which access the webserver and the Internet through the OpenVPN server. Also, external clients can access the OpenVPN from the Internet. The OpenVPN's server.conf is setup to use routing mode in udp, push DNS and routes to the network it is in so clients can access the webserver. Here are my very strict firewall rules. After connecting to the OpenVPN server, my clients can not access the Internet or the web server. When I allow FORWARD traffic to go through, it works just fine. The OpenVPN server has full internet connectivity. What firewall rule do I need to add to allow internet traffic to reach my clients?

    Read the article

  • Why is Linux choosing the wrong source ip address

    - by Scheintod
    and what to do to let it choose the right one? This all happens inside an OpenVZ container: The Host is Debian/Wheezy with Redhat/OpenVZ Kernel: root@mycl2:~# uname -a Linux mycl2 2.6.32-openvz-042stab081.5-amd64 #1 SMP Mon Sep 30 16:40:27 MSK 2013 x86_64 GNU/Linux The container has two (virtual) network interfaces. One in public and one in private address-space: root@mycl2:~# ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:127.0.0.2 P-t-P:127.0.0.2 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:775 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:32059 (31.3 KiB) TX bytes:56309 (54.9 KiB) venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:80.123.123.29 P-t-P:80.123.123.29 Bcast:80.123.123.29 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 venet0:1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.0.1.29 P-t-P:10.0.1.29 Bcast:10.0.1.29 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 The route to the private network is set manually: root@mycl2:~# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 venet0 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 venet0 Tring to ping others on the private network leads to the wrong source address been choosen: root@mycl2:~# ip route get 10.0.1.26 10.0.1.26 dev venet0 src 80.123.123.29 cache mtu 1500 advmss 1460 hoplimit 64 Why is this and what can I do about it? EDIT: If I create the route with (thanks to Joshua) ip route add 10.0.0.0/8 dev venet0 src 10.0.1.29 it is working. But according to man ip-route the src parameter should only set the source-ip if this route is chosen. But if this route is chosen then the source-ip would be that anyway.

    Read the article

  • TCP Sessions and IP Changes

    - by Kyle Brandt
    What happens to a TCP session when the IP of a client changes? I did a simple test of having netcat listen on a port, and connecting to that port from a client machine. I then changed the IP of the client while that nc session was open and sent some data, no data was received by server after changing the IP. I know they are different layers, but does TCP use IPs for part of how it distinguishes sessions? Does my example not work because of how the application handles it, or is this not working because of something happening at TCP/IP/Ethernet layers? Does this depend on the OS implementation? ( I am most interested in Linux at the moment)

    Read the article

  • UFW blocking webrick on port 3000

    - by t Book
    On a ubuntu 10.0.4 server runs redmine. starting webrick with: ./server webrick -e production -b lvps46-173-79-113.dedicated.hosteurope.de -d makes redmine available in browser. as soon as we enable ufw, webrick can´t be accessed anymore. of course we allowed Port 3000 from anywhere ufw allow 3000/tcp ufw allow 3000/udp also a grep for iptables doesn´t show a deny rule iptables -nL | grep 3000 find the whole iptables output here http://pastebin.com/k6WNqdPU checking lsof -ni tcp:2222 tells me ruby is listening on port 3000 ruby 3457 root 5u IPv4 864846667 0t0 TCP 46.173.79.113:3000 (LISTEN) What else can we check? what´s wrong with the ufw rules for port 3000?

    Read the article

  • Cisco ASA Multiple Public IP

    - by KGDI
    I have a Cisco ASA5510 and articles related to ASA and mulitple Public IP says this cant be done. My question is how to best solve a scenario like this: I have 3 zones, Outside, Inside and DMZ Outside is Internet Inside is Client machines DMZ is a zone for servers related to external and internal services. My scenario is a bit more complex, but to keep things simple this will do: I want to place an Exchange server and a web server (externally reachable in the DMZ zone) The webserver uses both TCP80/443, the Exchange server uses 443 So to the problem: With the ASA only having one public IP, how would you make a DNAT to port 443 on both the internal hosts behind 1 Public IP? Usually, when i do this kind of scenario With Linux boxes i use alias Interfaces like eth0:0, eth0:1 and set 1 Public IP on each. To me this must be a pretty common scenario, any ideas on how to solve it With ASA? /KGDI

    Read the article

  • How can I install a scanner by IP?

    - by user54266
    I'm trying to install a scanner by IP the same way you would install a printer by IP. I don't want to install the horrible HP Solution Center software but I don't know how to install a network scanner without the software. I'm having a hard time googling this because when I search for things like "install network scanner" or "install scanner by IP" all the results are for things like Angry IP Scanner which is clearly different than what I'm trying to get. Thanks in advance. This is for Windows Vista, but Windows 7 instructions will do.

    Read the article

  • Non-blocking service to receive messages on port via UDP

    - by stUrb
    I want to build a service on my Linux VPS which listens to a certain UDP port and does something with the (text)message which is captured. This processing consists of appending the message to a locally stored txt-file and send it as http, with a post variable to another server. I've looked into Nginx but as far is can see this server can only be bound to receive http packets. Although it is asynchronous. What is the best way to achieve this listening-service on linux? And which has the capabilities to do the above mentioned processing?

    Read the article

  • Static IP question

    - by blade
    If I want to set a static IP for my AD DS, do I need an ISP which provides this facility? Also, if my VMS also need a static IP, would this have to be another IP or can it be the same? (I know this sounds a bit noobish). Thanks

    Read the article

  • CentOS I/O blocking flushing dirtypages

    - by user3662224
    I have an Apache webserver on CentOS. It is not doing anything fantastic or complicated at all but it does at intervals experience a high load (120 for 4 CPUs) for some reason. During this time I see high waits and write durations. I have narrowed this down to flushing of dirtypages to disk to make room for new data. I have tried many things and talked to the developers who are also puzzled by this. I am stumped. Details: vmware virtual guest server 4 cpus 12G RAM Apache PHP I have 40 servers in this cluster that share the same disk structure. Only the webservers are experiencing this issue. Any ideas?

    Read the article

  • Server IP must be a LAN IP (Port Forwarding Netgear Router)? [closed]

    - by rphello101
    I'm trying to set up a server (Apache) on my computer (fairly new to it). As I understand it, for it to be accessible to other computers, I need to forward port 80. When I try to forward the port though, I get the error: Server IP must be a LAN IP. I noticed in ipconfig that my default gateway is different than my wireless router. My computer is not hardwired, not on WiFi. Furthermore, I do not, at this point, have a static IP. I read that it should still work with a dynamic IP until it changes. Any ideas on what I can do? I'm using Windows 7 in case it matters.

    Read the article

  • VPN instead of KVM over IP? [on hold]

    - by Blazer
    I have a server colocated on datacenter.CentOS operating system. They use KVM-ip when I need remote hands. Somoene told me that login using that will allow administrators (if they want) to get disk encryption password or ssh root pass via KVM-ip(is that true ?). Someone told me I can use VPN to login to my server instead of kvm over ip. Anyone have experience with that ? Is that option valid ? Thank you

    Read the article

  • iptable rules not blocking

    - by psychok7
    so i am trying to allow ssh access to a certain range of ips (from 192.168.1.1 to 192.168.1.24) and block all the rest but since i am new to iptables i can't seem to figure, i have : iptables -A INPUT -s 192.168.1.0/24 -p udp --dport ssh -j ACCEPT iptables -A INPUT -s 192.168.1.0/24 -p tcp --dport ssh -j ACCEPT iptables -A INPUT -p tcp --dport ssh -j REJECT iptables -A INPUT -p udp --dport ssh -j REJECT but this does not work, with a vm set with 192.168.1.89 i can still access through ssh. can someone help?

    Read the article

  • Why Wouldn't Root Be Able to Change a Zone's IP Address in Oracle Solaris 11?

    - by rickramsey
    You might assume that if you have root access to an Oracle Solaris zone, you'd be able to change the root's IP address. If so, you'd proceed along these lines ... First, you'd log in: root@global_zone:~# zlogin user-zone Then you'd remove the IP interface: root@user-zone:~# ipadm delete-ip vnic0 Next, you'd create a new IP interface: root@user-zone:~# ipadm create-ip vnic0 Then you'd assign the IP interface a new IP address (10.0.0.10): root@user-zone:~# ipadm create-addr -a local=10.0.0.10/24 vnic0/v4 ipadm: cannot create address: Permission denied Why would that happen? Here are some potential reasons: You're in the wrong zone Nobody bothered to tell you that you were fired last week. The sysadmin for the global zone (probably your ex-girlfriend) enabled link protection mode on the zone with this sweet little command: root@global_zone:~# dladm set-linkprop -p \ protection=mac-nospoof,restricted,ip-nospoof vnic0 How'd your ex-girlfriend learn to do that? By reading this article: Securing a Cloud-Based Data Center with Oracle Solaris 11 by Orgad Kimchi, Ron Larson, and Richard Friedman When you build a private cloud, you need to protect sensitive data not only while it's in storage, but also during transmission between servers and clients, and when it's being used by an application. When a project is completed, the cloud must securely delete sensitive data and make sure the original data is kept secure. These are just some of the many security precautions a sysadmin needs to take to secure data in a cloud infrastructure. Orgad, Ron, and Richard and explain the rest and show you how to employ the security features in Oracle Solaris 11 to protect your cloud infrastructure. Part 2 of a three-part article on cloud deployments that use the Oracle Solaris Remote Lab as a case study. About the Photograph That's the fence separating a small group of tourist cabins from a pasture in the small town of Tropic, Utah. Follow Rick on: Personal Blog | Personal Twitter | Oracle Forums   Follow OTN Garage on: Web | Facebook | Twitter | YouTube

    Read the article

  • IIS7.5 + Wordpress + Restrict Access to wp-login.php by client IP address

    - by JuanValdez
    I am moving from an Apache host to IIS. One of my sites in Wordpress (running Multi-site) which give me multiple blogs. I have moved all my rules from my .htaccess to the Microsoft URL ReWrite module. I have one section left that will not import. I want to restrict access to all instances of the file wp-login.php by Client IP address. In my .htaccess file I did the following: <Files wp-login.php> Order Deny,Allow Deny from all Allow from 192.168 </Files> Any smart ideas on how to accompish this in IIS7.5?

    Read the article

  • Simple thread-safe non-blocking file logger class in c#

    - by Jason Renlan
    I have a web application, that will log some information to a file. I am looking for a simple thread-safe non-blocking file logger class in c#. I have little experience with threading. I known there are great logging components out there like log4Net, Enterprise Library Logging Block, ELMAH, but I do not want an external dependence for my application. I was thinking about using this queue implementation http://www.codeproject.com/KB/cpp/lockfreeq.aspx

    Read the article

  • Cannot ping static ip on eth1

    - by Calvin Froedge
    I am trying to ping the network interface I have set up for eth1. This is my config: auto eth1 iface eth1 inet static address 192.168.1.2 netmask 255.255.255.0 gateway 192.168.1.1 broadcast 192.168.1.255 If I ping 192.168.1.2, I get: Ping 192.168.1.2 (192.168.1.2) 56(84) bytes of data. From 192.168.1.3 icmp_seq=3 Destination Host Unreachable Results of ifconfig tell me that the IPv4 address is 192.168.1.3. I can ping this ip. Bcast and Mask are as expected (same as in definition). I can ping 192.168.1.3 from my macbook. I cannot ping 192.168.1.2 locally or from my macbook. Any ideas why?

    Read the article

< Previous Page | 42 43 44 45 46 47 48 49 50 51 52 53  | Next Page >