Search Results

Search found 90601 results on 3625 pages for 'user friendly'.

Page 460/3625 | < Previous Page | 456 457 458 459 460 461 462 463 464 465 466 467  | Next Page >

• Windows 8.1 - Won't boot (0xc000000f), bcdedit fails

  - by user3014097

  I’m pretty much stuck at this point. So, backstory: Windows was installed on one of the SSDs currently in my tower. I bought a new SSD to install Windows (8.1 64 bit) on. Windows installation went fine, booted up, and formatted the old SSD from within Windows (this seems to have been a mistake, but I didn’t realize that at the time). Despite formatting the old SSD, whenever I tried to boot I was told that there were 2 Windows installations. Apparently, when I formatted the old drive, not all of the partitions were removed. So, I booted up with the repair utility, went into cmd, and deleted the non-primary partitions on the old SSD (there were 2 – think they were system and recovery, although I’m forgetting now). Reboot – computer won’t boot. Getting the 0xc000000f “The boot selection failed because a required device is inaccessible” error. Troubleshooting so far: Automatic repair doesn’t fix anything (I’ve never had luck with it though) If I go to install a new version of Windows, the drives and partitions are all there. The SSD is functioning, I at least know that. I’ve essentially gone through this guide: https://neosmart.net/wiki/recovering-windows-bootloader/ Unfortunately, I’m not getting anywhere. I’m not even entirely sure how to describe the errors I’m getting, so I’ve just included pictures of every step (I can't actually post them though so I just included a photobucket link). http://s319.photobucket.com/user/DGalt11/library/Computer%20Issue Am I completely screwed here (i.e. reformat and reinstall?)? Thanks

  Read the article

• prevalent, recurring hardrive failure intel macbook from 2006/2007

  - by SimonSalman

  Hi, Long story: My MacBook's hard drive failed one year ago, just a month after its warranty ended or: a year and a month after I bought it. After about ten phone calls to Apple's service, they agreed to extend the warranty for another year, so that I got it replaced free of charge. In the mean time, I got to know that many MacBook users that experience/report hard drive failures. Every reported crash was preceded by a slowdown of system performance, an increased occurrence of the spinning beach ball wait courser, and frequent crashes of applications that used to run very robust until then. It happened (as far as I know) with MacBooks from 2006/2007. All these MacBooks additionally suffer from a recurring wearing down of their "top case". Many heavy users had to replace their HDDs three time since 2006/2007 resulting in an head crash, making it impossible to recover data (diagnosis of recovery specialists) in most but not all cases HDD was Seagate (doesn't necessarily have to be the cause, if majority of the MacBook charge contained Seagate drives) And right now (one year after my first disk crash), these symptoms are cumulating on my system, again ... Short version: prevalent hard drive failure on MacBook charge from 2006/2007 (i.e. 2.16 GHz Intel Core 2 Due) I am looking for any (preferable open source) tool for checking the hard drive condition, especially to detect the known "MacBook problem". So, that I can replace the disk on time. If any Mac user found a solution to prevent the repeated failure of heir hard drive, I would be very glad to get to known it. I really enjoy my old MacBook, but I hate to get interrupted every year by an HDD crash. BTW, the issue is already in discussion for a long time, but there seems to be no solution, so far. Thanks, Simon

  Read the article

• What do I need to consider when buying hardware to meet my needs?

  - by Darth Android

  I'm looking to build a new computer from the ground up. I'm not sure what to look out for and need guidance and help on how to pick the hardware needed to construct my new rig. How do I know what to buy? How do I find out if a given CPU will be enough for a certain game or application that I want to run? How do I find out if a given graphics card will be enough for a certain game or application? What is important when looking at motherboards? How much memory do I need? How do I know how much wattage I need for a power supply? What size case do I need? What relevant standards do I need to read up on and be aware of? PCI, PCIe, SATA, USB 2.0, USB 3.0, etc... What "gotchas" do I need to be on the lookout for? Please keep responses generation-agnostic to ensure they will be helpful to our future users. While Stack Exchange does not permit shopping recommendations, it doesn't provide any general advice to consider when buying hardware. So, instead of just telling those that ask what to buy that it's not allowed, let's tell them how to figure out what they need. This question was Super User Question of the Week #20 Read the June 20, 2011 blog entry for more details or submit your own Question of the Week.

  Read the article

• Password Protect XML-RPC

  - by Terence Eden

  I have a service running on a server which I want to access via XML-RPC. I've installed all the necessary bits. Within /etc/apache2/httpd.conf I have the single line SCGIMount /RPC2 127.0.0.1:5000 I can run xmlrpc commands from my server - and any server which connects to /RPC2. What I want to do is password protect the directory to stop unauthorised usage. Within /etc/apache2/httpd.conf I've added <Location /RPC2> AuthName "Private" AuthType Basic AuthBasicProvider file AuthUserFile /home/me/myhtpasswd Require user me </Location> Trying to access /RPC2 brings up the "Authorization Required" box and it accepts my username and password. However, xmlrpc now doesn't work! If I run xmlrpc localhost some_command on my server, I get the error Failed. Call failed. HTTP response code is 401, not 200. (XML-RPC fault code -504) Is there any way I can password protect my /RPC2 directory and have xmlrpc commands work?

  Read the article

• Setup Version Control on Dreamweaver

  - by John Isaacks

  I have a win computer on the Network called WIN2K8FS1 I have TortoiseSVN on a win computer and when I go to checkout a repository with Tortoise it asks me for the URL of the repository. I put in: file://WIN2K8FS1/Media/SVN_repo And it creates the working copy. I am trying to setup Dreamweaver CS5 to work with subversion. I create a new site and I go to the Version Control tab and it asks for a lot if info. First is Access. I choose Subversion since that is the only option Second is Protocol. Not sure which I need so I go with HTTP? Third is Server Address. I am assuming this is the name of the computer with the repository so I put in \\WIN2K8FS1\ Fourth is Repository Path. I put in /Media/SVN_repo Fifth is Port which I leave default to 80 Then it asks for user name and password. I never set one up for anything so I put in my domain username and password. I click test and it tells me: Server and project are not accessible! I am not sure what I am doing wrong. I am not the server admin but I did create the repository and have access to it via Tortoise. So I am not sure what I am doing wrong in Dreamweaver.

  Read the article

• Can Safari 5.1 for Mac OS display favicons for bookmarks in the Bookmarks Bar?

  - by Greg R.

  When bookmarking a web site, most contemporary browser will display the site's favicon next to the bookmark, both in the bookmark view and the bookmark toolbar. This is a useful feature. In the bookmark toolbar you can edit the name of the bookmark to be blank, effectively leaving the favicon there as an easily identifiable "button" from which to launch the bookmark. This allows you to make more effective user of the space in the bookmark toolbar. I use this approach effectively in Firefox, Chrome, and IE. For example, here is a portion of my Bookmarks Toolbar from Firefox: However, in Safari, no favicon is ever displayed for bookmarks. In the full bookmark view only a generic globe icon is displayed. In the Bookmark Bar in Safari, no icon at all is displayed. Which means the habit of removing the bookmark name & leaving the favicon is useless. Here's what the same configuration (synced between browsers via Xmarks) looks like in Safari. That blank space is where the favicons should be. The boomark is there -- if you hover over it, the blank space changes color to indicate the presence of a bookmark and a tool tip will with the URL will pop up after about two seconds. However, it's really quite unusable. So. The question: is there an extension, plug-in, or modification of some sort that will enable the display of favicons for bookmarks in Safari (OS X Lion 10.7.3 , Safari version 5.1.3)?

  Read the article

• Looking for an application to record audio and video on a linux "embedded" device

  - by Luke404

  I am working with a linux x86 device with limited CPU resources (as a prototype we just use a pentium-m netbook). We'd like to record video from one V4L2 device (we'll probably end up using just USB Video Class devices like all modern webcams) and one audio stream from an ALSA source. The thing will not have screen and keyboard, and obviously no X11 environment. Goals are: do as little work as possible to cope with little cpu resources - for example I'd like to record video in the native MJPEG I get out of the UVC devices encoding audio to MPEG3 Layer-2 (aka mp2) is ok since it let us save a lot of space (compared to raw pcm samples) and does use little cpu power I don't mind loosing some video frames here and there (UVC devices do that) as long as I can get audio and video streams syncronized not require user input to start the thing (a python script takes care of initialization, startup, shutdown, etc...) be able to open the resulting files for postprocessing without too much effort (ie, if mplayer or vlc can play it, it's fine) So far the only app I found that could be started from command line and record V4L2 video + ALSA audio is mencoder but I'm having some difficulties with it. It should be able to do that but I cannot record audio and video together - just one of the two. And if I use two different processes to record to two different files I have no means to get them in sync (audio is more or less always correct, but video framerate will vary over time and it seems to lack timestamps to correctly play it back to the correct time). Long story short, how do you record an unconverted MJPEG stream (from an UVC device) and an audio stream (from an ALSA device, possibly encoding to any standard format) using a command line tool, to a single file (MPEG or any other container), keeping audio and video in sync?

  Read the article

• How to forceably unmount stuck network share in Mac OS X?

  - by Kyle Lowry

  Not long ago my Xserve failed (power loss) while an iMac was working with files on a particular network share (called "Work Share"). This volume, "Work Share", is now stuck. It can't be seen in the GUI, you can only detect it using the Terminal. Even after power cycling over the course of several days, ls -a still shows that it's there, but I can't unmount it using any command - not even as root in single user mode. Every time I attempt to unmount that volume, I get the message that the resource is busy (which it can't possibly be since nothing is using it), and error code 4915. The issue is that when I mount the real "Work Share", it internally is renamed to "Work Share-1", which breaks all my links, and several files in the share. If I can't unmount the false "Work Share", then that computer would be unuseable without a reformat, I would imagine - and I don't want it to have to come to that. I've tried everything I can think of - it looks like sudo can't save me now. Any ideas on how to unmount this stuck volume?

  Read the article

• Using GUI ftp on Win7 and Vista without additional software

  - by Stephen Jones

  Goal: provide a 'no-software' method for 'less technical' users to access password protect ftp location from Win7 and Vista (existing approach for WinXP works). 'No software' method to mean without installing additional software (e.g. FileZilla, WinSCP) - the solution is supplied to external non-technical users. WinXP (works): Using Windows Explorer, WinXP supports non-technical ftp access by pasting: ftp://username:[email protected] into the address bar. The remote ftp site's files / directory structure becomes available and can be copied to / from easily (in the style of local file copy / paste) by a 'less technical' user. Win7 / Vista (doesn't work): Pasting the same URL into the Windows Explorer on Win7 or Vista causes an error: An error occurred opening that folder on the FTP server. Make sure you have permission to access that folder. Details: The connection with the server was reset. Notes: a) The same username/password/server typed from the (DOS) command line achieves access to the server, but this is a more 'technical' solution than desired. I am looking for a WinXP equivalent solution. b) Under 'Control Panel' / 'Internet options' / 'Advanced' tab - the boxes for 'Enable FTP folder view' and 'Use Passive FTP' are ticked (enabled) c) Adding an inbound firewall rule for local port 20 (TCP) was attempted with no difference in results (i.e. failure)

  Read the article

• Triple-monitor set-up (2 unique, 1 cloned): Can a VGA splitter be used on one output of a dual-head

  - by stakx

  Background: I'm currently researching hardware components for some kind of information terminal we're building. This application of ours makes use of three output screens: (1) A touch screen where all user input is made; (2) A regular LCD monitor where the requested information is being displayed; and (3) A projector which displays exactly the same signal as screen (2) does. (All screens will run at the same resolution of 1024x768 btw.) Now I figured that using a dual-head video card would be sufficient, let's say a Matrox P690 low-profile PCI card. This would involve having a Y cable connected to the graphics card itself, then two DVI-to-VGA adapters at each end of the Y cable, and then having a VGA splitter on one of the VGA outputs. The following shows the setup in question: 0--1---------2-> VGA (DSUB-15) \ \ ----2-3---------> VGA (DSUB-15) \ \ -----------------> VGA (DSUB-15) 0: graphics card (LFH60 jack) 1: LFH60 to DVI-I dual monitor Y cable 2: DVI-to-VGA adapters 3: VGA splitter cable Question(s): Will this work? I'm particularly concerned about the following points: Can a low-profile PCI video card output a signal which is strong enough for three monitors (even if it's a dual-head card)? Does the combination of so many adapters and splitter cables work? (The LFH-to-DVI cable comes with the video card) Will the VGA splitter cable degrade the signal on the output screen & projector significantly? (If so, would a USB-powered splitter cable remedy this problem?) I can't possibly expect anyone to answer all those questions, but any input is appreciated.

  Read the article

• Why is SSH finding remote keys for other accounts?

  - by Brian Pontarelli

  This is a strange issue I'm having with SSH from my Macbook Pro to a Linux (Ubuntu 11.10) server. I have a DSA key setup on the remote Linux server under my home directory like this: /home/me/.ssh/authorzied_keys I also have the same DSA key setup for a few other accounts on the machine named "foo" and "bar". I can log into all of the accounts fine without any password. Therefore, the DSA keys are all setup correctly. The strange behavior I'm seeing is when debugging the SSH connection. During the connection, the SSH debug is outputting this: debug2: key: /Users/me/.ssh/id_dsa (0x7f91a1424220) debug2: key: /home/foo/.ssh/id_dsa (0x7f91a1425620) debug2: key: /home/bar/.ssh/id_rsa (0x7f91a1425c60) debug2: key: /Users/me/.ssh/id_rsa (0x0) This is strange for so many reasons, but essentially, why is SSH listing out keys on the server (/home/foo/.ssh/id_dsa and /home/bar/.ssh/id_rsa)? These files don't even exist on the server, so why are they listed? I'm not logging into the "foo" or "bar" accounts, so why is SSH even listing those? On my Macbook Pro, I only have a DSA key, but SSH is listing out an RSA key, what's that all about? Another user on the server doesn't get any of these messages when they log in and they have the exact same setup for their DSA key and the exact same Macbook Pro setup as mine? Does anyone know what these messages are and why SSH is outputting them?

  Read the article

• Office 2007 constantly crashes, logged as Event ID 1000

  - by Nori

  I have a user, who despite my best efforts, is having constant Office 2007 crashes. I've tried deleting their profile and setting it up again, repairing office, uninstalling completely and then reinstalling, and swapping out memory sticks. One event log error I keep getting is the following: (note all the Office errors are event id 1000) Faulting application name: OUTLOOK.EXE, version: 12.0.6539.5000, time stamp: 0x4c12486d Faulting module name: EMSMDB32.DLL, version: 12.0.6539.5000, time stamp: 0x4c1246f8 Exception code: 0xc0000005 Fault offset: 0x0005d8e2 Faulting process id: 0xf6c Faulting application start time: 0x01cb6633f33384f3 Faulting application path: C:\Program Files (x86)\Microsoft Office\Office12\OUTLOOK.EXE Faulting module path: c:\progra~2\micros~1\office12\EMSMDB32.DLL Report Id: 0d4a2eab-d231-11df-80a0-4061868f5d10 I also get this: Faulting application name: OUTLOOK.EXE, version: 12.0.6539.5000, time stamp: 0x4c12486d Faulting module name: olmapi32.dll, version: 12.0.6538.5000, time stamp: 0x4bfc6ad9 Exception code: 0xc0000005 Fault offset: 0x002357a9 Faulting process id: 0x5e4 Faulting application start time: 0x01cb661f4546aa77 Faulting application path: C:\Program Files (x86)\Microsoft Office\Office12\OUTLOOK.EXE Faulting module path: c:\progra~2\micros~1\office12\olmapi32.dll Report Id: a4a90658-d224-11df-80a0-4061868f5d10 The Excel error is this: Faulting application name: EXCEL.EXE, version: 12.0.6535.5002, time stamp: 0x4bd2a7f1 Faulting module name: KERNELBASE.dll, version: 6.1.7600.16385, time stamp: 0x4a5bdbdf Exception code: 0xe06d7363 Fault offset: 0x0000b727 Faulting process id: 0x14a8 Faulting application start time: 0x01cb61ab7bc0abab Faulting application path: C:\Program Files (x86)\Microsoft Office\Office12\EXCEL.EXE Faulting module path: C:\Windows\syswow64\KERNELBASE.dll Report Id: ba0c454b-cd9e-11df-80a0-4061868f5d10 Also have gotten this for PowerPoint: Faulting application name: POWERPNT.EXE, version: 12.0.6500.5000, time stamp: 0x49a68f9d Faulting module name: COMShim.dll, version: 2010.3.325.110, time stamp: 0x4c51e0b1 Exception code: 0x40000015 Fault offset: 0x0001e388 Faulting process id: 0x1480 Faulting application start time: 0x01cb5fe9a0660e81 Faulting application path: C:\Program Files (x86)\Microsoft Office\Office12\POWERPNT.EXE Faulting module path: C:\Program Files (x86)\FactSet\COMShim.dll Report Id: e03d2a21-cbdc-11df-9bc8-4061868f5d10 (Some of the above lines edited to keep you from scroll horizontally.) Lastly, I get this error several times a day, I don't think it is related but maybe it is: Failed extract of third-party root list from auto update cab at: http://www.download.windowsupdate.com/msdownload/update/v3/static/trustedr/en/authrootstl.cab with error: A required certificate is not within its validity period when verifying against the current system clock or the timestamp in the signed file. Any ideas? This is driving me nuts.

  Read the article

• [Mac OS X] Terratec Cinergy Hybrid T USB XS is not recognized anymore

  - by Gabble

  I have used Terratec Cinergy Hybrid T USB XS for years now, alongside with Elgato EyeTV software. I am a happy and completely satisfied user! Since a couple of weeks the USB sitck stopped working on my MacPro1,1 (OS version 10.6.3): EyeTV does not see any device attached, and actually, the green led on the stick stays off. 1) it is not a USB port fault: I have unplugged any other USB/Firewire device and tried with different USB ports, to no avail (any other USB devices work as expected on any port) 2) I have completely uninstalled EyeTV software, including preferences and system daemons/extensions, rebooted and reinstalled the latest EyeTV. No way. 3) reset the PRAM. Nope. 4) checked the Apple System Profiler - USB: No device attached, The MacPro does not see it at all. ============= I need to say that: a) the device worked as a charm even with the latest OS 10.6.x (so it's not a OS upgrade cause) b) I have plugged the Terratec Cinergy Hybrid T USB XS to my MacBook5,1 where EyeTV is not installed and was never installed: The green led on the stick turns on, the growl bubble pops up, and the device is perfectly recognized by the system. Apple System Profiler says (sorry, Italian language): Cinergy Hybrid T USB XS (2882): ID prodotto: 0x005e ID fornitore: 0x0ccd Versione: 1.10 Numero di serie: 061102005755 Velocità: Fino a 12 Mb/sec Produttore: TerraTec Electronic GmbH ID posizione: 0x04100000 Corrente disponibile (mA): 500 Corrente necessaria (mA): 500 At this point I am pretty sure the Terratec stick is not damaged and there is something wrong with my MacPro. I kindly ask you: Is there a way to force my MacPro recognize the USB device? What can I check? Is there something that caches USB connection that can be reset? A OS reinstall would be the very last resort for me… Thanks in advance for any help you will offer!

  Read the article

• 1and1 ssh - connection refused

  - by kitensei

  I'm having troubles connecting through SSH to my 1&1 account. When I try to connect with command userXXX@host -p22 -vv I have the following output: OpenSSH_5.8p1 Debian-7ubuntu1, OpenSSL 1.0.0e 6 Sep 2011 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to mySite.com [ip_here] port 22. debug1: connect to address ip_here port 22: Connection refused Moreover, once I try to connect through SSH and it fails, even the HTTP access is dead, I cannot access the website through explorer anymore :/ please help < I'm running ubuntu 11.10 EDIT: don't know if it can help, here's the .htaccess of the 1and1 server Options +Indexes Satisfy any Order Deny,Allow Allow from 212.227.X.X Deny from all RemoveType .html .gif AuthType Basic AuthName "Access to /logs" AuthUserFile /kunden/homepages/43/d376072470/htpasswd Require user "user_here" and sftp.log: Mar 26 09:21:24 193.251.X USER_HERE Connection from 193.251.X port 51809 Mar 26 09:21:30 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:39 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:41 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:45 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:57 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 10:53:36 212.227.X tmp64459736-3228 Connection from 212.227.X port 23275 Mar 26 10:53:36 212.227.X tmp64459736-3228 Accepted password for tmp64459736-3228 from 212.227.X port 23275 ssh2 Mar 26 11:53:37 212.227.X tmp64459736-3228 Connection closed by 212.227.X Mar 26 18:58:17 212.227.X tmp64459736-5363 Connection from 212.227.X port 23353 Mar 26 18:58:17 212.227.X tmp64459736-5363 Accepted password for tmp64459736-5363 from 212.227.X port 23353 ssh2 Mar 26 19:53:36 212.227.X tmp64459736-8525 Connection from 212.227.X port 5166 Mar 26 19:53:36 212.227.X tmp64459736-8525 Accepted password for tmp64459736-8525 from 212.227.X port 5166 ssh2 Mar 26 19:58:17 212.227.X tmp64459736-5363 Connection closed by 212.227.X

  Read the article

• Debian - starting UFW (Uncomplicated Firewall) before network interfaces are operational

  - by Tomasz Zielinski

  I want to install UFW on Debian Lenny. Everything looks straightforward except that I don't know where to plug UFW startup script so that it configures iptables before hax0rs can break in. I've reviewed runlevel directories and in /etc/rc0.d, /etc/rc6.d and /etc/rcS.d there are items like these: S35networking -> ../init.d/networking S36ifupdown -> ../init.d/ifupdown Runlevel 0 and 6 are for shutdown and reboot so I guess nothing should be changed there, but runlevel S advertises itself (in README) like something for me: The scripts in this directory whose names begin with an 'S' are executed once when booting the system, even when booting directly into single user mode. The following sequence points are defined at this time: * After the S40 scripts have executed, all local file systems are mounted and networking is available. All device drivers have been initialized. (What bothers me is that both rc0/6.d and rcS.d point to the same networking and ifupdown scripts, but after looking at sources I believe those scripts are smart enough to figure out where to start and where to stop networking.) Now, I think that I should plug my /lib/ufw/ufw-init into /etc/rcS.d, with priority higher that the one of ifupdown and networking, i.e. <= 38 for my /etc/rcS.d. Am I right in this "analysis" ?

  Read the article

• Apple / Mac OS X - Is there a Package Manager like Linux

  - by Walter White

  I am a Linux/UNIX user and love the package management that comes with it. For the most part, I like Ubuntu, but just like anything else, it is the minor things that you live with daily that would be nice if they just worked. My main issue is my wacom tablet while it works, every time there is an OS update, I have to rebuild the wacom driver. The other slightly annoying issue is, my ATI video card is not fully supported. When I use the HDMI out, the sound doesn't go through it, and the screen is not entirely used. I would happily get an Apple if it had a similar package management system like Ubuntu, Gentoo, or other Linux distribution. This takes the work out of getting the latest enhancements or fixes. It also takes all the guess work out about what you need to get something to work. I just want to use my computer, not administer it. Aside from Apple applications, if I wanted to install the GIMP on an apple, would it go and fetch ufraw if I wanted support for that and whatever other dependencies GIMP has? If I want Netbeans installed, will it go and get a JDK and maven if I want that? If not, is there something in the works? I know I don't update my applications that frequently, but that is mainly because I'm not aware of the updates. The updates all happen in the background. Walter

  Read the article

• Getting Apache to serve same directory with different authentication over SSL?

  - by Lasse V. Karlsen

  I have set up VisualSVN server, a Subversion server that internally uses Apache, to serve my subversion repositories. I've managed to integrate WebSVN into it as well, and just now was able to get it to serve my repositories through WebSVN without having to authenticate, ie. no username or password prompt comes up. This is good. However, with this set up there is apparently no way for me to authenticate to WebSVN at all, which means all my private repositories are now invisible as far as WebSVN goes. I noticed there is a "Listen 81" directive in the .conf file, since I'm running the server on port 81 instead of 80, so I was wondering if I could set up a https:// connection to a different port, that did require authentication? The reason I need access to my private repositories is that I have linked my bug tracking system to the subversion repositories, so if I click a link in the bug tracking system, it will take me to diffs for the relevant files in WebSVN, and some products are in private repositories. Here's my Location section for WebSVN: <Location /websvn/> Options FollowSymLinks SVNListParentPath on SVNParentPath "C:/Repositories/" SVNPathAuthz on AuthName "Subversion Repository" AuthType Basic AuthBasicProvider file AuthUserFile "C:/Repositories/htpasswd" AuthzSVNAccessFile "C:/Repositories/authz" Satisfy Any Require valid-user </Location> Is there any way I can set up a separate section for a different port, say 8100, that does not have the Satisfy Any directive there, which is what enable anonymous access. Note that a different sub-directory on the server is acceptable as well, so /websvn_secure/, if I can make a location section for that and effectively serve the same content only without the Satisfy Any directive, that'd be good too.

  Read the article

• Windows 7 VPN Error 619

  - by TravisPUK

  So I am running Windows 7 Enterprise. This morning I was able to VPN using the built in VPN (Connect to Work Network etc). I had to change my network's IP address range and now the VPN will not work. It just stalls on the Verifying user name and password... message. But then it returns the 619 error. Anybody know why changing my machine's IP address would cause this problem? Where should I be looking to try and fix this issue? I have tried this on a Windows XP machine that also had the IP address range change and this still connects fine using exactly the same connection details. EDIT The internal network range changed from 192.x.x.x to 10.x.x.x. This was done on the entire Active Directory. All machines are running fine and the Windows XP machine, that works going to the same client VPN mentioned above is on the same network. Both the XP and the Win 7 machines are using DHCP served by the Domain Controller. The client domain is not performing any IP range checks/restrictions. The VPN is outside the internal network, connection is being made via the Internet and not passing through any other machine, other than the normal domain machines, ie DNS etc. This is passing through a router and the router has the relevant VPN passthrough options configured. All internal machines are working correctly with other forms of VPN, ie Cisco, Sonic etc (these were tested on other machines, they are not installed on the Vista or Win7 machines). After further testing, this is occurring on all Win7 and Vista machines where they can no longer connect to the client VPN, however all XP machines can still connect fine. This has been tested on three Vista, two Win7 and five XP machines. All machines are on DHCP and tests have been done with both the firewalls turned on and off, as well as with fixed IPs being used. Thanks Travis

  Read the article

• DriveImage XML fails with a Windows Volume Shadow Service Error

  - by ssvarc

  I'm trying to image a SATA laptop hard drive, using DriveImageXML, that is attached to my computer via a USB adapter. I'm running Win7 Ultimate 64 bit. DriveXML is returning: Could not initialize Windows Volume Shadow Service (VSS). ERROR C:\Program Files (x86)\Runtime Software\Drivelmage XML\vss64.exe failed to start. ERROR TIMEOUT Make sure VSSVC.EXE is running in your task manager. Click Help for more information. VSSVC.EXE is running in Task Manager, as is VSS64.exe. Looking at the FAQ on the Runtime webpage this turned up: Please verify in Settings-Control Panel-Administrative Tools-Services that the following services are enabled: MS Software Shadow Copy Provider Volume Shadow Copy Also make sure you are able to stop and start these services. Possible reasons for VSS failures: For VSS to work, at least one volume in your computer must be NTFS. If you use only FAT drives, VSS will not function. The required NTFS volume does not need to be identical with the volume you want to image. You should make sure that VSSVC.EXE is running in your task manager. If the problems persist, registering "oleaut.dll" and "oleaut32.dll" using "regsvr32" might help. Both of those services are running and can be started and stopped without issue. Using "regsvr32" to register ""oleaut32.dll" returns successful, but "oleaut.dll" returns: The module "oleaut.dll" failed to load. Make sure the binary is stored at the specified path or debug it to check for problems with the binary or dependent .DLL files. The specified module could not be found. Some other information that might be relevant. Browsing to the drive is successful, but accessing certain folders returns an "access" error. Windows runs a permissions adder that adds the current user profile to the NFTS permissions. Could this be the cause of the issue? DriveImage XML is running as Administrator. Thoughts?

  Read the article

• /dev/input/uinput Device appears to be 'broken'

  - by Adam Luchjenbroers

  I'm trying to setup Pystromo so that I can remap the keys on my Belkin N52TE gamepad. Pystromo basically captures the key strokes and then outputs the remapped keystrokes to the uinput device. However, at the moment it simply swallows the input and outputs absolutely nothing. I've tracked the issue to something being wrong with my uinput device, with the smoking gun being: # ls -l /dev/input/uinput crw-rw---- 1 root plugdev 10, 223 Dec 31 2009 /dev/input/uinput # cat /dev/input/uinput cat: /dev/input/uinput: No such device The uinput module is loaded, and can be clearly seen via lsmod. Anyone seen this before, or can think of something worth attempting? Current Setup Gentoo Linux Kernel 2.6.32 (Gentoo Sources 2.6.32-r1) HP DV7 Laptop Output dmesg dmesg | grep uinput does nothing, and no new lines appear if I run modprobe -r uinput && modprobe uinput. Yet the uinput module can clearly be seen when running lsmod: # lsmod | grep uinput uinput 6200 0 lsusb # lsusb Bus 005 Device 003: ID 050d:0200 Belkin Components Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 1532:0101 Razer USA, Ltd Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 5986:0143 Acer, Inc Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 002: ID 03f0:171d Hewlett-Packard Wireless (Bluetooth + WLAN) Interface [Integrated Module] Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub lsusb -v PasteBin Update Hmm, updating evdev and hal seems to have partially fixed it. /dev/input/uinput still can't be accessed but Pystromo is now remapping keys successfully. I'm a little bit mystified about what's going on here, but it seems that my understanding of how all this works is flawed. Since I've posted a bounty, I'll leave this here for someone to post an explanation for how user-space input devices work under the hood.

  Read the article

• Wget save cookies not working

  - by TrymBeast

  I've been trying to login in the pyload through the web api, but wget is not saving the cookies and I don't understand why. I'm using the following command: wget --delete-after --keep-session-cookies --save-cookies=my_cookies.txt --post-data="username=USERNAME&password=PASSWORD" http://localhost:8000/api/login But the content of my_cookies.txt is: # HTTP cookie file. # Generated by Wget on 2012-06-23 22:31:33. # Edit at your own risk. When I run the same command but in debug mode I get the following output that includes the set cookie in the header response: DEBUG output created by Wget 1.10.2 (Red Hat modified) on linux-gnueabi. --22:31:11-- http://localhost:8000/api/login Resolving localhost... 127.0.0.1 Caching localhost => 127.0.0.1 Connecting to localhost|127.0.0.1|:8000... connected. Created socket 3. Releasing 0x000504d0 (new refcount 1). ---request begin--- POST /api/login HTTP/1.0 User-Agent: Wget/1.10.2 (Red Hat modified) Accept: */* Host: localhost:8000 Connection: Keep-Alive Content-Type: application/x-www-form-urlencoded Content-Length: 32 ---request end--- [POST data: username=USERNAME&password=PASSWORD] HTTP request sent, awaiting response... ---response begin--- HTTP/1.1 200 OK Content-Length: 34 Content-Type: application/json Cache-Control: no-cache, must-revalidate Set-cookie: beaker.session.id=405390ddc809efed54820638c95d7997; expires=Tue, 19-Jan-2038 04:14:07 GMT; Path=/ Connection: Keep-Alive Date: Sat, 23 Jun 2012 21:31:11 GMT Server: CherryPy/3.1.2 WSGI Server ---response end--- 200 OK hs->local_file is: login (not existing) Registered socket 3 for persistent reuse. TEXTHTML is on. Length: 34 [application/json] Saving to: `login' 100%[=======================================>] 34 --.-K/s in 0s 22:31:11 (1.28 MB/s) - `login' saved [34/34] Removing file due to --delete-after in main(): Removing login. Saving cookies to my_cookies.txt. Done saving cookies. Can anyone tell me what am I doing wrong? Thanks in advance!

  Read the article

• Win7 Credential manager and accessing SQL Server from outside of the domain

  - by David Lively

  My SQL Server is set to use windows authentication. If I am connected to the domain directly from my Win7 Ultimate x64 machine, SQL Management Studio (SSMS) will let me authenticate with Windows authentication. However, if I am connected via the VPN (from a different machine that is not joined to the domain), it won't. If I start SSMS with the following command line: C:\Windows\system32>runas /netonly /user:domainname\username "C:\Program Files (x86)\Microsoft SQL...\ssms.exe" then connecting to the SQL Server (which is in the domain) with Windows Authentication works fine. I'd like to save these credentials so that I don't have to launch SSMS from the command line, or modify the shortcut. I know I can use the SysInternals ShellRunAs extension to do this, but I again have to enter my domain username and password each time, and shift+right-click to see that menu option. The Windows Credential Manager seems designed to solve this problem, and works for network shares. However, it doesn't seem to work for SSMS. Any suggestions? I've tried using the /savecred option with runas to create the necessary credentials, but that appears to be incompatible with the /netonly option. Running the above command line with the addition of /savecred just displays the runas help screen. Grrr. Argh.

  Read the article

• Windows XP only loads in VGA mode, and crashes when raising resolution

  - by Harel

  My kid's computer (Windows XP, SP3) started to (what appears to be) crash on boot. It will only boot in Safe or VGA mode, and if I try to raise the resolution from 640x480 it just reboots itself, and a error appears in the Event Log. When it loads up not in VGA mode, the monitor shuts off just after the windows logo is shown. It seems like windows is actually running but I can't see anything on screen (monitor is off for lack of signal). Nothing was installed recently that I know of, short of the usual windows updates. Thanks, Harel Below is the event log error: Event Type: Error Event Source: System Error Event Category: (102) Event ID: 1003 Date: 15/04/2012 Time: 16:27:11 User: N/A Computer: ----- Description: Error code 1000008e, parameter1 c0000005, parameter2 f745b0bf, parameter3 ede24f98, parameter4 00000000. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 53 79 73 74 65 6d 20 45 System E 0008: 72 72 6f 72 20 20 45 72 rror Er 0010: 72 6f 72 20 63 6f 64 65 ror code 0018: 20 31 30 30 30 30 30 38 1000008 0020: 65 20 20 50 61 72 61 6d e Param 0028: 65 74 65 72 73 20 63 30 eters c0 0030: 30 30 30 30 30 35 2c 20 000005, 0038: 66 37 34 35 62 30 62 66 f745b0bf 0040: 2c 20 65 64 65 32 34 66 , ede24f 0048: 39 38 2c 20 30 30 30 30 98, 0000 0050: 30 30 30 30 0000

  Read the article

• pppd disconnects from 3G, doesn't reconnect, w/ persist set

  - by bytenik

  I am trying to configure pppd to connect to a 3G network (Sprint, in this case) and then stay connected, reconnecting automatically if the remote connection is terminated. I have enabled the persist option. My configuration file is as follows: hide-password noauth connect "/usr/sbin/chat -v -f /etc/chatscripts/cellular" debug /dev/cell 921600 defaultroute noipdefault user " " persist maxfail 0 lcp-echo-failure 10 lcp-echo-interval 60 holdoff 5 However, when the peer disconnects the connection, pppd often waits a long time (substantially more than my holdoff) to reconnect the modem -- if it ever reconnects at all! An example log showing this: May 23 05:17:24 00270e0a8888 pppd[2408]: rcvd [LCP TermReq id=0x26] May 23 05:17:24 00270e0a8888 pppd[2408]: LCP terminated by peer May 23 05:17:24 00270e0a8888 pppd[2408]: Connect time 60.1 minutes. May 23 05:17:24 00270e0a8888 pppd[2408]: Sent 0 bytes, received 0 bytes. May 23 05:17:24 00270e0a8888 pppd[2408]: Script /etc/ppp/ip-down started (pid 2456) May 23 05:17:24 00270e0a8888 pppd[2408]: sent [LCP TermAck id=0x26] May 23 05:17:24 00270e0a8888 pppd[2408]: Script /etc/ppp/ip-down finished (pid 2456), status = 0x0 May 23 05:17:24 00270e0a8888 pppd[2408]: Hangup (SIGHUP) May 23 05:17:24 00270e0a8888 pppd[2408]: Modem hangup May 23 05:17:24 00270e0a8888 pppd[2408]: Connection terminated. May 23 05:17:24 00270e0a8888 pppd[2408]: Terminating on signal 15 May 23 05:17:24 00270e0a8888 pppd[2408]: Exit. May 23 06:08:07 00270e0a8888 pppd[2500]: pppd 2.4.5 started by root, uid 0 May 23 06:08:10 00270e0a8888 pppd[2500]: Script /usr/sbin/chat -v -f /etc/chatscripts/cellular finished (pid 2530), status = 0x0 May 23 06:08:10 00270e0a8888 pppd[2500]: Serial connection established. May 23 06:08:10 00270e0a8888 pppd[2500]: using channel 11 The disconnect at the request of the peer occurs at 5:17, but the reconnect didn't happen until 6:08. I had a friend monitoring the server so I'm not certain that this wasn't a manual reconnection. Either way, it either took almost an hour to reconnect or never reconnected. Shouldn't persist + holdoff 5 cause this to automatically reconnect after 5 seconds of the link terminating?

  Read the article

• Software to automate website screenshot capture

  - by Leniel Macaferi

  Do you know any software that can automate the process of getting screenshots of every page of a website? It would act like a spider/crawler/robot. You name it... For example: I developed a website and now I'd like to get a screenshot of every page of the site. I of course could do it manually (a lot of work). For each module of the site (Student, Payment, etc) I have different pages (Create, Edit, Details, Delete, etc) forms. The thing I'm looking for is a software that can visit every link of the site and then capture the screen - a software that can automate the whole process. It would also be good if the software allowed the user to pass a list of URLs to capture screenshots allowing even more fine grained configuration. EDIT: I tried Selenium mentioned by Aaron in his answer but I managed to find an app that does exactly what I needed. It's called Paparazzi!. I wrote a blog post to showcase my attempt at Selenium and the findings regarding Paparazzi!'s batch capture functionality: Software to automate website screenshot capture

  Read the article

< Previous Page | 456 457 458 459 460 461 462 463 464 465 466 467  | Next Page >