Search Results

Search found 1425 results on 57 pages for 'cisco catalyst'.

Page 47/57 | < Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >

• solaris + dladm + what is unknown state and how to bring it to up?

  - by yael

  I installed Solaris 10 on my netra machine from dladm show-dev I can see which interface are down or up all interfaces are connected to the Cisco switch , and all leds are light's on all LAN cards but I not understand why all interfaces except e1000g0 are in unknown ? Please advice how to bring the unknown interfaces to up ? # dladm show-dev e1000g0 link: up speed: 1000 Mbps duplex: full e1000g1 link: unknown speed: 0 Mbps duplex: unknown e1000g2 link: unknown speed: 0 Mbps duplex: unknown e1000g3 link: unknown speed: 0 Mbps duplex: unknown nxge0 link: unknown speed: 0 Mbps duplex: unknown nxge1 link: unknown speed: 0 Mbps duplex: unknown nxge2 link: unknown speed: 0 Mbps duplex: unknown nxge3 link: unknown speed: 0 Mbps duplex: unknown

  Read the article

• What equipment do real ISP's use?

  - by Allanrbo

  In a dormitory of 550 residents, people often mistakenly set up DHCP servers for the whole network by plugging in their private Wi-Fi routers wrongly. Also recently, someone mistakenly configured their PC to a static IP being the same as that of the default gateway. We use cheap 3Com switches at the moment. I know that Cisco switches support DHCP snooping to solve the DHCP problem, but that still does not solve the default gateway IP takeover problem. What sort of switch equipment do real ISP's use so their customers cannot break the network for the other customers?

  Read the article

• Can't connect to VPN in Windows XP mode

  - by darkstar13

  I have Windows 7 x32 installed on my laptop. I have also Windows XP mode installed. My setup is that my work-remote programs are in Windows XP mode because my VPN installer in Windows XP only. Lately, I have been having troubles getting on / logging in to VPN. I can access the internet in WinXP mode but When I ping the IP address of the target IP of my VPN network (or even just Google.com), I always get a 'Request Timeout'. However, when I ping the same IP address in command prompt in Windows 7, I get 100% data sent. Is there anything I need to adjust? Before, I have been able to connect instantly. Now, it's like trial and error, or I will have to wait for hours just to be able to enter logon credentials in Cisco VPN dialer. NAT is my network adapter in XP mode.

  Read the article

• How do I connect to the serial console port os a Sunfire 280R?

  - by DrStalker

  We have a Sunfire 280R (old SPARC/Solaris server) that is refusing to come up after being relocated. We're trying to connect to the serial console port, but all we get is random gibberish on the screen. We've tried both connecting with a DB25DB9 adapter and using a DB-25-RJ45 adapter with a cisco RJ45-DB9 adapter to a windows laptop. We're configuring the laptop to 9600 baud, 8 bit, 1 stop bit, no parity. We've tried both no flow control and Xon/Xoff. We get the same results hooking up to the serial port on a working SPARC server, so it's probably something in our setup rather than a fault with the server. How do we get access to to serial console so we can work out what is stopping this box from getting to the network? Is there a special sun adapter we need to get/make to get the serial link working?

  Read the article

• Any ideas for automatic initial/scripted configuration of a NetApp?

  - by maddenca

  The background is to make a solution where we can automate as much as possible the building up of ‘pods’ that include server/network/storage and that will be built at remote sites. In an ideal world would be that we create a single management server which is preconfigured with DHCP/TFTP/or whatever. This management server is racked with a CISCO UCS, FAS31x0, etc. at a build site and is then transported to the final customer site where on power it almost configures itself, or at least bootstraps itself far enough that a remote skilled 'expert' can complete the setup of the pod. Ideas (doesn't have to resemble 100% of the above) would be helpful.

  Read the article

• How can you enable SMB2.0 on a router running DD-WRT?

  - by jeffreypriebe

  I think the steps are something like: Install DD-WRT on a router with an external hard-drive Install Optware to get Samba Upgrade to Samba 3.6 (the link shows Samba 3.5, but using the NSLU2 optware packages, you can get 3.6 with built-in SMB2.0) ...then a miracle occurs... Then you can use SMB2.0 to connect to your share What is step 4? I can't find it on forums, etc. Am using Microsoft Network monitor to check for SMB2.0 connection, I'm on Windows 7 and have tried network connections on wireless and gigabit wired to the router. No joy. I doubt it matters, but to get ahead of the questions: DD-WRT v24-sp2 (10/26/10) big (SVN revision 15508M NEWD-2 K2.6 Eko) on Cisco/Linksys E3000

  Read the article

• Wrong source IP when accessing internet directly from TMG server

  - by jarod1701

  Hi everyone, after implementing a ForeFront TMG server I'm facing only one problem: After I added a second IP to the external adapter I had to manually set "NAT Address Selection" inside the network rule "Internet Access" to the first IP since all others would get blocked by the CISCO firewall. This configuration works as long as traffic comes from the internal network (e.g. browser on clients). Traffic from the TMG directed to the internet always carries the second IP as it's source address and gets blocked. All our other TMGs/ISAs are running fine and I never came across this problem- Does anybody have a clue, coz I don't?! Kevin

  Read the article

• Cage nuts - which way to insert them?

  - by Ingmar Hupp

  Cage nuts can be inserted (in square holes) either with the flaps horizontal or vertical. I've seen and used both methods, but am still not sure which is best. Is there a recommended way of inserting them? If so, why is it the best way? From my own experience, the horizontal way (on the left) seems slightly better for no other reason than making it easier to insert or pry out the cage nut in a full rack (with the units above and below being populated), for example when replacing cage nuts with a snap-in rail. Edit: Major vendors each seem to have their own preference too: Horizontal: IBM, Cisco, APC Vertical: HP (and Compaq), Sun/Oracle, Dell

  Read the article

• Remote Desktop app can't connect through VPN or through RDP load balancer

  - by nhinkle

  Using the regular Remote Desktop Client (in the desktop environment) I can connect just fine to remote servers when connected through Cisco VPN or when accessing a server behind a load balancer. When using the Remote Desktop app in the Modern UI, I can't do either of these things. Trying to connect to a remote server that's on a private network fails with: Can't find server, make sure the name and domain are correct and try again And connecting to a server that's behind an RDP load balancer fails with the following error, after accepting credentials: Because of a protocol error, this session will be disconnected. Please try connecting to the remote PC again Is there some way to use the Remote Desktop app in these situations, or am I just out of luck?

  Read the article

• Virtual Desktop Provisioning - Vmware View 5.2 Maintenance Questions

  - by Lee J. DeAngelis

  Currently running an environment of about 400 VMware View 5.2 virtual Desktops. The environment runs pretty efficiently but we sometimes run into problems with certain pools from time to time. Just recently we had a pool that was causing high write latency when users logged in. It just happened all of a sudden and had been working fine for weeks. On a hunch we completely broke down the pool and re-provisioned it from a new image. This corrected the problem. In fact every real issue we've had so far was fixed by a recompose or complete break down and re-provisioning of one pool or another.Our environment consists of Cisco UCS and Netapp 3240s using flashcache running VMware View 5.2. My questions are: What are some maintenance best practices other VDI admins are using? How often are you recomposing? rebalancing? re-provisioning? How long should you keep base image snapshots around?

  Read the article

• Storage product testing

  - by wildchild

  hello, I know this is out of place (being an active member here i am coming for the help from seniors) ,but i need some information regarding storage testing ,testing of Raid arrays, SCSI, SAS ,SATA and also test carried out on fabric manager(Cisco MDS series switches). I am aware that this is an administrative forum and i would really appreciate if you could direct me to the correct forum ar links where i can learn things . @ moderators-Sorry for posting at the wrong place,i would be deleting this as soon as i get the help. Thanks !

  Read the article

• Can a Linksys Router be the cause of bad speeds on a 1.5 mbps link.

  - by gramware

  We use a Linksys 5-port router at a smal organization with about 20 employees. We recently acquired a 1.5 mbps fibre link, but sometimes the link goes down and speeds are still low. On enquirey from the ISP, this was part of the response, However there maybe throttling due to the router in place. A Linksys is a low end router and may be unable to carried traffic of up to 1536Kbps. We are in a position to deploy a Cisco 871 router on test for 2 wks to eliminate that possibility. Also kindly advise the destination of the ping results they look to high. How true is that about the router throttling the network and need for a bigger one.

  Read the article

• IPTables masquerading with one NIC

  - by Tuinslak

  Hi, I am running an OpenVPN server with only one NIC. This is my current layout: public.ip > Cisco firewall > lan.ip > OpenVPN server lan.ip = 192.168.22.70 The Cisco firewall forwards the requests to the oVPN server, thus so far everything works and clients are able to connect. However, all clients connected should be able to access 3 networks: lan1: 192.168.200.0 (vpn lan) > tun0 lan2: 192.168.110.0 (office lan) > eth1 (gw 192.168.22.1) lan3: 192.168.22.0 (server lan) > eth1 (broadcast network) So tun0 is mapped to eth1. Iptables output: # iptables-save # Generated by iptables-save v1.4.2 on Wed Feb 16 14:14:20 2011 *filter :INPUT ACCEPT [327:26098] :FORWARD DROP [305:31700] :OUTPUT ACCEPT [291:27378] -A INPUT -i lo -j ACCEPT -A INPUT -i tun0 -j ACCEPT -A INPUT -i ! tun0 -p udp -m udp --dport 67 -j REJECT --reject-with icmp-port-unreachable -A INPUT -i ! tun0 -p udp -m udp --dport 53 -j REJECT --reject-with icmp-port-unreachable -A FORWARD -d 192.168.200.0/24 -i tun0 -j DROP -A FORWARD -s 192.168.200.0/24 -i tun0 -j ACCEPT -A FORWARD -d 192.168.200.0/24 -i eth1 -j ACCEPT COMMIT # Completed on Wed Feb 16 14:14:20 2011 # Generated by iptables-save v1.4.2 on Wed Feb 16 14:14:20 2011 *nat :PREROUTING ACCEPT [302:26000] :POSTROUTING ACCEPT [3:377] :OUTPUT ACCEPT [49:3885] -A POSTROUTING -o eth1 -j MASQUERADE COMMIT # Completed on Wed Feb 16 14:14:20 2011 Yet, clients are unable to ping any ip (including 192.168.200.1, which is the oVPN's IP) When the machine was directly connected to the internet, with 2 NICs, it was quite simply solved with masquerading and adding static routes in the oVPN client's config. However, as masquerading won't accept virtual interfaces (eth0:0, etc) I am unable to get masquerading to work again (and I'm not even sure whether I need virtual interfaces). Thanks. Edit: OpenVPN server: # ifconfig eth1 Link encap:Ethernet HWaddr ba:e6:64:ec:57:ac inet addr:192.168.22.70 Bcast:192.168.22.255 Mask:255.255.255.0 inet6 addr: fe80::b8e6:64ff:feec:57ac/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6857 errors:0 dropped:0 overruns:0 frame:0 TX packets:4044 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:584046 (570.3 KiB) TX bytes:473691 (462.5 KiB) Interrupt:14 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:334 errors:0 dropped:0 overruns:0 frame:0 TX packets:334 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:33773 (32.9 KiB) TX bytes:33773 (32.9 KiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.200.1 P-t-P:192.168.200.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ifconfig on a client: # ifconfig eth0 Link encap:Ethernet HWaddr 00:22:64:71:11:56 inet addr:192.168.110.94 Bcast:192.168.110.255 Mask:255.255.255.0 inet6 addr: fe80::222:64ff:fe71:1156/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3466 errors:0 dropped:0 overruns:0 frame:0 TX packets:1838 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:997924 (974.5 KiB) TX bytes:332406 (324.6 KiB) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:37847 errors:0 dropped:0 overruns:0 frame:0 TX packets:37847 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2922444 (2.7 MiB) TX bytes:2922444 (2.7 MiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.200.30 P-t-P:192.168.200.29 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:689 errors:0 dropped:18 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:468778 (457.7 KiB) wlan0 Link encap:Ethernet HWaddr 00:16:ea:db:ae:86 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:704699 errors:0 dropped:0 overruns:0 frame:0 TX packets:730176 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:520385963 (496.2 MiB) TX bytes:225210422 (214.7 MiB) static routes line at the end of the client's config (I've been playing around with the 192.168.200.0 -- (un)commenting to see if anything changes): route 192.168.200.0 255.255.255.0 route 192.168.110.0 255.255.255.0 route 192.168.22.0 255.255.255.0 route on a vpn client: # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.200.29 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 192.168.22.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.200.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.110.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.110.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.110.1 0.0.0.0 UG 0 0 0 eth0 edit: Weirdly enough, if I set push "redirect-gateway def1" in the server config, (and thus routes all traffic through VPN, which is not what I want), it seems to work.

  Read the article

• tacacs integration with database

  - by chingupt

  We are setting up TACACS+ in our network which is a mix of Cisco AP's and other brands. However we have a centralized managemnet system which allows our customers to centrally configure services. Hence we would like to setup a tacacs+ server integrated with some database. Can this be done? I found the following package at www.shrubbery.net/tac_plus/ but it does not have the necessary plugins for database. Please let me know how to go about this. TIA Sachin

  Read the article

• Wireless technology - which is better: more single radio APs or less dual radio APs?

  - by gert_78

  We are currently talking to vendors of wireless solutions for a wireless deployment in a university campus with some 5000 students. One vendor is offering us a Cisco solution with a WLC 5508 controller and 69 2x2 MIMO Dual-band/Dual radio APs (Aironet AP 1042 model) The other vendor is offering us an Aruba solution with a 3600 controller and 96 2x2 MIMO dual band BUT single radio APs (Aruba AP93) Both vendors are charging 82.000 US$ (support, 3y service contracts, switches and additional required options all included of course) The Aruba vendor is trying to convince me that 96 single radio APs will give us more connection/users/capacity then the 69 dual radio APs. I have my doubts about that and since it is my core competence-domain I wanted to ask here the opinion of people that have a more profound knowledge and experience in this area. When you talk to vendors it's often hard to get objective information. So try to answer only if you are sure and please mention it if you are affiliated with one of the vendors. I appreciate all useful help and want to thank you in advance for the effort!

  Read the article

• Where are Credentials stored for Network Drives on WinXP?

  - by Tom Tresansky

  I have a drive mapped to a folder on a remote machine that I connect to using the Cisco VPN client. The password to the Windows account I use on that remote machine has changed. I had stored the username/password locally, using Window's remember my password feature, so I wouldn't have to enter it every time (the enter user/password login dialog used to appear each time I attempted to open the remote folder, and I would have to look up and enter my credentials). The password to that remote Windows account has changed. Now, I am no longer prompted to enter a user name / password, but instead, upon trying to open the remote folder, receive a message: unknown user name or bad password. How do I view and change these stored credentials?

  Read the article

• EC2-like virtualisation platform with non-RDP access

  - by code'

  I'm looking into setting up a few small VMs. The trouble is the software I intend to install on them (Cisco VPN Client) blocks out networking (other than to the target VPN destination...) with no workaround. This means that Remote Desktop or other methods of connecting to VMs that go via the Internet (e.g. GoToMyPC, LogMeIn) are a non-starter. What I'm really looking for is an EC2-like platform but which gives direct access to the VM through (for example) Hyper-V Manager. Sadly the only way they all seem to offer to remote control the VMs is direct access via Remote Desktop, whereas I need to be one layer above that (if that makes sense). A viable alternative would be to run virtualisation software within a Windows EC2 instance; obviously hardware virtualisation is impossible but I wonder if there are any software virtualisation platforms that could be run and that would work. Does anyone know if something like this exists/is possible? Thanks! C

  Read the article

• What equipment do real ISP's use?

  - by Allanrbo

  In a dormitory of 550 residents, people often mistakenly set up DHCP servers for the whole network by plugging in their private Wi-Fi routers wrongly. Also recently, someone mistakenly configured their PC to a static IP being the same as that of the default gateway. We use cheap 3Com switches at the moment. I know that Cisco switches support DHCP snooping to solve the DHCP problem, but that still does not solve the default gateway IP takeover problem. What sort of switch equipment do real ISP's use so their customers cannot break the network for the other customers? What we ended up doing In case anyone are courious, we ended up doing seperate VLANs for each user. And as a matter of fact, not just the 550 users, but for 2500 users (11 dorms). Here's a page describing the setup: http://k-net.dk/technicalsetup/ (the section "Transparent firewall using VLANs"). There was no significant load on the router server as I feared in one of the comments below. Even at 800Mpbs.

  Read the article

• Can I set up a 2nd home wireless router, with router2 connecting to the internet through a desktop which is wirelessly connected to router1?

  - by gil b.

  Hi, I apologize for the crudeness of my MSPaint drawing, but please view my diagram of what I'd like to accomplish: Proposed home network architecture Currently, all devices are connected to 1 wireless router. I would like to make my own subnet, with a box in-between my subnet and the shared wireless router, so that I can learn about IDS, traffic analysis, etc. I was also given a cisco PIX firewall to play around with, and it'd be an added bonus if I could incorporate that into my network. The reason for this proposed architecture is so that I can monitor all MY traffic, without seeing anything going on with my roommates' traffic. my MAIN Question is, is it possible to have my desktop connect to the wireless router with internet via wireless card AND share that connection via the ethernet card, hooked to wireless router 2? cable modem - wireless router - desktop pc connected wirelessly - wireless router 2 getting internet from wired connection to desktop pc - laptops connected wirelessly The PIX can be left out for now, but I'm wondering if it could eventually be incorporated? THANKS!

  Read the article

• WS2008R2 / W7PRO: Cannot rename folder - folder redirection

  - by castor

  After few months from migrating one of my networks on Active Directory this issue started. A few users are encountering an issue from time to time - they cannot rename folders and files on desktop. The system throws an error saying the folder or file is already in use. Folder redirection takes place in this scenario (Desktop and My Documents) Subnet with user PCs is different from subnet with servers (Cisco ASA5505 Security Plus between - all inspection policies disabled on these interfaces) Users are running Windows 7 Professional x86 Server is running Windows Server 2008 R2 Standard Any ideas?

  Read the article

• A Linux DHCP server that will listen on an non-broadcast (tap) interface?

  - by TomOnTime

  Are there any Linux DHCP servers that will listen to what Cisco calls an "unnumbered" interface, or what others might call a "NBMA" (non-broadcast) interface. I have a Linux system that connects to a number of others using GRE tunnels. The machines on the other end send DHCP requests to this machine, I can see them with tcpdump. However, ISC DHCP 3.0.3 refuses to listen to the interface because it is non-broadcast. The interface I'd like DHCP to listen to is: tap2 Link encap:Ethernet HWaddr removed-for-privacy inet6 addr: removed-for-privacy/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:518 errors:0 dropped:0 overruns:0 frame:0 TX packets:510 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:196242 (191.6 KiB) TX bytes:52425 (51.1 KiB)

  Read the article

• Process of carrying out a BER Test

  - by data

  I am subscribed to an ISP supplying a 3meg ADSL line. Lately (for the last 4 weeks) speeds have dropped from the usual average downstream speed of ~250kbps to just 0.14Mbps (according to speedtest.net) and employees are complaining about lack of access to the server. I have been calling customer support and logging calls for the last 3 weeks, but they have been unable to determine the source of the problem other than carrying out a few bitstream tests and checking the DHCP renewal times. I am going to call back and suggest carrying out a BER test. What type of equipment is needed to carry out this test? I have access to a wide range of Cisco networking equipment. Other: We don't need a leased line as there are less than ten employees.

  Read the article

• VPN: What should my Gateway remote ID be?

  - by Lynn Owens

  I have a Netgear ProSafe UTM. I set the Gateway local ID to it's WAN IP. But I'm not sure what to put for it's Remote ID. I want to be able to connect to it from a laptop across the internet. I can chose between: Remote IP FQDN Client FQDN Cert DN Frankly I've tried them messing around with them all but I'm just shooting in the dark, and the help desk docs are worthless. Also, Googling around seems to end up with lots of pages not really related to what I want. A lot of pages on configuring Cisco or Windows home networking or privacy advocates.

  Read the article

• DVD player Ubuntu 9.10

  - by pcguynardone

  Hello everyone at SeverFault. I am new to this fourm. I have been using ubuntu since 8.04. Here is my problem. When I try to watch one of my cisco videos I get wmas error. I never had to use this format before. I went on ubuntu fourm they told me to use vlc media. I am using vlc media. mplayer, it still have error with that, sounds and video. Is there a program that I could use to watch wmas files on my ubuntu 9.10. It is a laptop ACer Extensa 5620z. Thank you for who ever will help !!

  Read the article

• DVD player Ubuntu 9.10

  - by pcguynardone

  Hello everyone at SeverFault. I am new to this fourm. I have been using ubuntu since 8.04. Here is my problem. When I try to watch one of my cisco videos I get wmas error. I never had to use this format before. I went on ubuntu fourm they told me to use vlc media. I am using vlc media. mplayer, it still have error with that, sounds and video. Is there a program that I could use to watch wmas files on my ubuntu 9.10. It is a laptop ACer Extensa 5620z. Thank you for who ever will help !!

  Read the article

< Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >