Search Results

Search found 25783 results on 1032 pages for 'enterprise service bus'.

Page 476/1032 | < Previous Page | 472 473 474 475 476 477 478 479 480 481 482 483  | Next Page >

• System says memory controller not available and doesn't boot?

  - by Martin

  Hello everybody, Recently I have had a MainBoard-problem. I've send my mainboard to service and today I got it back from the company. It is a Foxconn 520a mainboard. Now I have installed my exchanged mainboard. But now I have a problem. My system boots until the device list with IRQ entries appear. The system says "Verifying DMI-pool-data..." and nothing happens. The IRQ-device list shows that the memory-controller is not available. All other devices have got an IRQ. Bus No. Device No. Func No. Vendor/Device Class Device Class IRQ 0 0 0 10DE 0547 0500 Memory Controller NA Do you have any ideas where the problem could be? I already have disconnected all unnecessary devices like the hard disks. Perhaps it is a BIOS problem, but I don't know where I should look. Would be nice if there is any advice, Greetings, Martin

  Read the article

• 912 stream processor available in OpenCL

  - by tugrul büyükisik

  I am thinking of assembling this system: AMD CPU (A8-3870 APU which has Radeon HD 6550D inside: 400 stream processors:xxx GFLOPS) nearly 110$ AMD Graphics card: HD 7750 (512 stream processors:819 GFLOPS peak performance) nearly 170$ Appropriate ram (1600MHz bus) Mainboard What GFLOPS level can I reach as a stable mode with using OpenCL and similar programs? Can I use all 912 stream processors at the same time? I am not trying to do a VS question. I need to know what could be better for scientific computing (%75 of the time) and gaming (%25 of the time) because I have a low budget. With "scientific calculations" I mean fluid dynamics/solid state physics simulating; with games I mean those that need openCL and PhysX.

  Read the article

• upgrading my computer system for office use

  - by denise ellul

  Presently I have the under-mentioned computer system. What should be changed and upgraded with the following products that I own presently? I am interested in performance issues related to cache memory, bus speed, RAM, CAS latency as well as other considerations. Thanks for your help. Processor (CPU): Intel Celeron Dual Core E3300 2.5 GHz Motherboard: Asus P5QPL-AM G41 Main Memory (RAM): 2 GB Team Elite DDR2 PC8000 Case: Coolermaster RC330 Power Supply Unit: 500W EZ-Cool Standard Storage Device (Hard Drive): 500GB Samsung Video Card: Intel GMA X4500 (On-board) Optical Drive: LG GH22NS50 Sound Card: AC 97 (On – board) Card Reader: Akasa Black TFT Monitor: 19” View Sonic Speakers: Logitech S120 2.0

  Read the article

• Brand New MOnitor Won't Get Input From CPU

  - by HollerTrain

  I have an old Dell 2350. I found a HD a few months ago and plugged it in and it booted up. So I just purchased a monitor and plugged it in, and put the HD inside and connected the two connections (Bus, and a four pronged connector) and no signal is being sent to monitor. is this a monitor issue or the HD is just dead? HD is spinning. CPU is turned on :) Yet no signal.. any thoughts?

  Read the article

• Logitech M185 Wirless Mouse issue

  - by Elliot Harrison

  An issue with a Logitech M185 mouse today. A user is unable to use the device. The device works perfectly fine on my PC (It appears as HID-compliant mouse), but not on her laptop. It does not appear in her device manager on the 'Mice and other pointing devices' section. I did notice an unknown device in the Universal Serial Bus Controllers section, but when I try to update the driver, it says it has the most up to date driver. We've tried plugging in the dongle in multiple USB slots but no luck. Any advice? It's a HP 620 Laptop on Windows 7. Thank you :)

  Read the article

• Is an Ethernet point to point connection without a switch real time capable?

  - by funksoulbrother

  In automation and control, it is commonly stated that ethernet can't be used as a bus because it is not real time capable due to packet collisions. If important control packets collide, they often can't keep the hard real time conditions needed for control. But what if I have a single point to point connection with Ethernet, no switch in between? To be more precise, I have an FPGA board with a giga-Ethernet port that is connected directly to my control PC. I think the benefits of giga Ethernet over CAN or USB for a p2p connection are huge, especially for high sampling rates and lots of data generation on the FPGA board. Am I correct that with a point to point connection there can't be any packet collisions and therefore a real time environment is given even with ethernet? Thanks in advance! ~fsb

  Read the article

• Should USB controller drivers be updated?

  - by Coldblackice

  Should USB controller drivers be updated? In Windows 7, many of the core system devices/buses/controllers still use stock Microsoft drivers dating back to 2006 -- things such as USB controllers and the PCI bus (and subsequent devices in the tree). Should these be getting updated? I would think that surely there would have been improvements/fixes/updates to some or any of these drivers by now, now over 7 years old. Does Windows know "best" in this case, updating these respective drivers when it's needed, or should the user be keeping an eye out for drivers in this "vein" of devices (meaning integrated/core/non-pluggable system devices that are built into the motherboard)?

  Read the article

• MD3200i Slow Performance and Queue Depth

  - by Caleb_S

  Read performance on our SAN is slow under certain workloads. When we compare this to some local storage, we find the local storage performing 2x as fast. The SAN performs well with a high Queue Depth, and poorly with a low queue depth. However, the local storage performs well with a low Queue Depth. I'd like to know the reason for this occurring and find out what the specific limiting factor is in this situation. MD3200i iSCSI SAN ($15,000) 6 x 600GB 15k SAS RAID5 6 x 2TB 7.2k NLS RAID5 XCOPY /j Benchmark: (Slow) 15k Array - 71MB/s (Queue Depth 1) 7.2k Array- 71MB/s (Queue Depth 1) Robycopy /MT:32 Benchmark: (Fast) 15k Array - 171MB/s (Queue Depth ~12) 7.2k Array- 128MB/s (Queue Depth ~12) , , Read Performance on a Local controller is fast under the workload the SAN is slow at. , HighPoint 2230 RAID Controller ($600) 4 x 1TB 7.2k SATA RAID5 XCOPY /j Benchmark: 7.2k Array - 145MB/s (Queue Depth 1) (appears to max out the SATA bus)

  Read the article

• if there are multiple kernel module can drive the same device, what is the rule to choose from them?

  - by Dyno Fu

  both pcnet32 and vmxnet can drive the device. $ lspci -k ... 02:01.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] (rev 10) Subsystem: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] Flags: bus master, medium devsel, latency 64, IRQ 19 I/O ports at 2000 [size=128] [virtual] Expansion ROM at dc400000 [disabled] [size=64K] Kernel driver in use: vmxnet Kernel modules: vmxnet, pcnet32 both kernel modules are loaded, $ lsmod | grep net pcnet32 32644 0 vmxnet 17696 0 mii 5212 1 pcnet32 as you see, kernel driver in use is vmxnet. is there any policy/algorithm in kernel how to choose from the candidates?

  Read the article

• ata error: UnrecovData Handshk

  - by Aaron Digulla

  I just saw this message in my log (openSUSE 11.3, Linux 2.6.36.2): ata6.00: exception Emask 0x10 SAct 0x1 SErr 0x400100 action 0x6 frozen ata6.00: irq_stat 0x08000000, interface fatal error ata6: SError: { UnrecovData Handshk } ata6.00: failed command: WRITE FPDMA QUEUED ata6.00: cmd 61/58:00:9f:69:00/00:00:00:00:00/40 tag 0 ncq 45056 out res 40/00:04:9f:69:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error) ata6.00: status: { DRDY } ata6: hard resetting link ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata6.00: configured for UDMA/133 ata6: EH complete Two questions: Which disk caused the error? I search /sys and /proc but couldn't find a way to map ata6 to a device (/dev/sdaXY) When such an error happens, does Linux retry the disk operation? Or do I have a corrupt filesystem?

  Read the article

• How to tell if OpenGL is really working in Ubuntu 10.04

  - by Jonathan

  I have a lenovo S9e running Intel integrated graphics. Here is my lspci output related to the graphics: 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) Subsystem: Lenovo Device 3870 Flags: bus master, fast devsel, latency 0 Memory at f0580000 (32-bit, non-prefetchable) [size=512K] Capabilities: [d0] Power Management version 2 I want to know how I can make sure OpenGL support is running in full on an Ubuntu 10.04 installation. I have a few hints to think that it is not: The "Desktop Effects" will not load Apps such as stardock, when attempting to use OpenGL rendering, will display black boxes instead of transparency In the games Pioneers, the number-tile icons are suspiciously just black circles Windows games running with Wine will only support software rendering, not hardware rendering When I boot into a Knoppix LiveCD, the desktop effects do work, splendidly, meaning compiz detects my computer as capable. My problem with troubleshooting is that Canonical has basically eliminated the conf-file-based mechanism of X11 as far as I can tell, thus making it even harder to ensure graphics modules are loading properly. How do I debug and test OpenGL on m Ubuntu 10.04 installation?

  Read the article

• ARM Debian (squeeze) USB driver with mismatch 3.3.3 kernel but /lib/modules/2.6.36

  - by frank

  Hei guys, my sheevaplug embedded server works fine, but when I wanted to use USB, the device gets not attached to /dev/tty/USB0 lsusb shows correctly: Bus 001 Device 002: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port an modprobe usbserial raises: FATAL: Could not load /lib/modules/3.3.3/modules.dep: No such file or directory in the /lib/modules/ Folder there is instead a 2.6.36-Folder uname -r gives 3.3.3 How can I overcome this mismatch? Can I create a symlink? I can't flash this embedded device since it is deployed somewhere, only ssh? Please advise!

  Read the article

• Brand New Monitor Won't Get Input From Computer

  - by HollerTrain

  I have an old Dell 2350. I found a HD a few months ago and plugged it in and it booted up. So I just purchased a monitor and plugged it in, and put the HD inside and connected the two connections (Bus, and a four pronged connector) and no signal is being sent to monitor. is this a monitor issue or the HD is just dead? HD is spinning. CPU is turned on :) Yet no signal.. any thoughts?

  Read the article

• help building a PC that can image a dozen hard drives simultaneously

  - by Bigbio2002

  Not sure if this belongs on here or SuperUser, but here goes... I'm trying to figure out how to make a mass hard drive imaging PC out of COTS parts. A dedicated imaging device can do 10 drives at a time, but costs several thousand dollars. So far, I'm thinking to use several 3-port PCI-E Firewire cards, and use some kind of Firewire-to-IDE adapter to connect the drives themselves. The "software" would consist of scripting diskpart, or some other imaging utility. The problem is that I can't seem to find any sort of adapter. I could use standard external hard drive bays, but then I'd have a dozen power cables that I need to plug in. Ugly, messy, and inefficient. I picked Firewire over USB not only for better transfer speeds, but also because FW can deliver power over the bus (and could theoretically power a hard drive). Does anyone have any input on this?

  Read the article

• Motherboard memory question

  - by JERiv

  I am currently drawing up specs on a new workstation for my office. I am considering the Asus P6X58D for a motherboard. This board's specs list it as supporting 24 gigs of memory. Suppose I were to use six four gig memory cards and then two video cards with 1 gig of memory apiece. Is the maximum supported memory similar to how 32 bit operating systems only have enough address space for 4 gigs of memory? Simply: Will the board post? If so, will the system be able to address all the memory, both the 24 gigs on the ddr3 bus and the 3 gigs on the graphics card?

  Read the article

• Computer won't reboot without waiting for a while

  - by Benjamin

  I've got an unusual problem with my computer. When ever I reboot my computer it won't boot, I get a few beeps from the BIOS and nothing else, however if I wait for a few minuets the computer will boot perfectly. I tried to count the beeps and I get around 7-9 of them; the first two are noticeably closer together than the rest. [Edit: I'm now reasonably confident it's 1 long followed by 8 short beeps. That would be a display related issue: http://www.bioscentral.com/beepcodes/amibeep.htm] My BIOS is American Megatrends Inc and version P1.80, the Motherboard is an ASRock X58 Extreme (both according to dmidecode) Here's an output from LSPCI, I'm not sure what else might be useful but I can provide whatever's asked. 00:00.0 Host bridge: Intel Corporation 5520/5500/X58 I/O Hub to ESI Port (rev 13) 00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 (rev 13) 00:03.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 (rev 13) 00:07.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 7 (rev 13) 00:14.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub System Management Registers (rev 13) 00:14.1 PIC: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch Pad Registers (rev 13) 00:14.2 PIC: Intel Corporation 5520/5500/X58 I/O Hub Control Status and RAS Registers (rev 13) 00:14.3 PIC: Intel Corporation 5520/5500/X58 I/O Hub Throttle Registers (rev 13) 00:1a.0 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 00:1c.1 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 2 00:1c.5 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 6 00:1d.0 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA AHCI Controller 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 02:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6315 Series Firewire Controller 02:00.1 IDE interface: VIA Technologies, Inc. VT6415 PATA IDE Host Controller (rev a0) 03:00.0 SATA controller: JMicron Technology Corp. JMB360 AHCI Controller (rev 02) 05:00.0 VGA compatible controller: nVidia Corporation GT200b [GeForce GTX 285] (rev a1) ff:00.0 Host bridge: Intel Corporation Xeon 5500/Core i7 QuickPath Architecture Generic Non-Core Registers (rev 05) ff:00.1 Host bridge: Intel Corporation Xeon 5500/Core i7 QuickPath Architecture System Address Decoder (rev 05) ff:02.0 Host bridge: Intel Corporation Xeon 5500/Core i7 QPI Link 0 (rev 05) ff:02.1 Host bridge: Intel Corporation Xeon 5500/Core i7 QPI Physical 0 (rev 05) ff:03.0 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller (rev 05) ff:03.1 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Target Address Decoder (rev 05) ff:03.4 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Test Registers (rev 05) ff:04.0 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 0 Control Registers (rev 05) ff:04.1 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 0 Address Registers (rev 05) ff:04.2 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 0 Rank Registers (rev 05) ff:04.3 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 0 Thermal Control Registers (rev 05) ff:05.0 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 1 Control Registers (rev 05) ff:05.1 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 1 Address Registers (rev 05) ff:05.2 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 1 Rank Registers (rev 05) ff:05.3 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 1 Thermal Control Registers (rev 05) ff:06.0 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 2 Control Registers (rev 05) ff:06.1 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 2 Address Registers (rev 05) ff:06.2 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 2 Rank Registers (rev 05) ff:06.3 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 2 Thermal Control Registers (rev 05) Update: ok I installed lm-sensors and here's the output. coretemp-isa-0000 Adapter: ISA adapter Core 0: +58.0°C (high = +80.0°C, crit = +100.0°C) Core 1: +59.0°C (high = +80.0°C, crit = +100.0°C) Core 2: +58.0°C (high = +80.0°C, crit = +100.0°C) Core 3: +57.0°C (high = +80.0°C, crit = +100.0°C) it8720-isa-0a10 Adapter: ISA adapter in0: +0.93 V (min = +0.00 V, max = +4.08 V) in1: +0.06 V (min = +0.00 V, max = +4.08 V) in2: +3.25 V (min = +0.00 V, max = +4.08 V) +5V: +2.91 V (min = +0.00 V, max = +4.08 V) in4: +3.04 V (min = +0.00 V, max = +4.08 V) in5: +2.94 V (min = +0.00 V, max = +4.08 V) in6: +2.14 V (min = +0.00 V, max = +4.08 V) 5VSB: +2.96 V (min = +0.00 V, max = +4.08 V) Vbat: +3.28 V fan1: 1869 RPM (min = 0 RPM) fan2: 0 RPM (min = 0 RPM) fan3: 0 RPM (min = 0 RPM) fan4: 1106 RPM (min = -1 RPM) fan5: 225000 RPM (min = -1 RPM) temp1: +39.0°C (low = +0.0°C, high = +127.0°C) sensor = thermistor temp2: +56.0°C (low = +0.0°C, high = +127.0°C) sensor = thermistor temp3: +127.0°C (low = +0.0°C, high = +127.0°C) sensor = thermistor cpu0_vid: +1.650 V intrusion0: ALARM If it helps here's the summery from sensors-detect Driver `it87': * ISA bus, address 0xa10 Chip `ITE IT8720F Super IO Sensors' (confidence: 9) Driver `adt7475': * Bus `NVIDIA i2c adapter 3 at 5:00.0' Busdriver `nvidia', I2C address 0x2e Chip `Analog Devices ADT7473' (confidence: 5) Driver `coretemp': * Chip `Intel digital thermal sensor' (confidence: 9)

  Read the article

• Apps not starting on Mac OS X Lion

  - by KPS

  I have a strange problem, some apps that I download do not launch. There are 2 scenarios The application starts but keeps bouncing, once I click the bouncing icon in the tray it disappears. The process also closes in activity monitor The application fails to start, how ever many times I launch it, it refuses. The process does not even show up in activity monitor What I have done so far to resolve: Repaired permissions Clear all cache/temp using CleanMyMac Used DiskWarrior via OS and not during boot Additional Info: Model Name: MacBook Pro Model Identifier: MacBookPro5,2 Processor Name: Intel Core 2 Duo Processor Speed: 2.8 GHz Number of Processors: 1 Total Number of Cores: 2 L2 Cache: 6 MB Memory: 8 GB Bus Speed: 1.07 GHz Boot ROM Version: MBP52.008E.B05 SMC Version (system): 1.42f4

  Read the article

• Need help upgrading MacBookPro3,1 RAM to 4GB.

  - by Fantomas

  My questions are: 1) Where to buy it and what to buy? I have heard that this RAM is generic enough and it does not have to come from Apple. 2) Can I reuse my existing stick(s)? Would I have a single 2GB module, or 2 x 1GB modules? 3) If I have 2GB already, is it a good idea to have one old stick and one new one? Which one is better placed at the top and which one at the bottom? Let me know what questions you have. My computer's info: Hardware Overview: Model Name: MacBook Pro Model Identifier: MacBookPro3,1 Processor Name: Intel Core 2 Duo Processor Speed: 2.4 GHz Number Of Processors: 1 Total Number Of Cores: 2 L2 Cache: 4 MB Memory: 2 GB Bus Speed: 800 MHz Boot ROM Version: MBP31.0070.B07 SMC Version (system): 1.16f11

  Read the article

• Random Server shutdown? - CentOS

  - by Kevin Hammett

  My system was working fine, and then it just had a random restart. Anyone have any idea of the problem? The message log: Jul 6 22:56:34 909I7 shutdown[719711]: shutting down for system halt Jul 6 22:56:34 909I7 init: Switching to runlevel: 0 Jul 6 22:56:35 909I7 smartd[10743]: smartd received signal 15: Terminated Jul 6 22:56:35 909I7 smartd[10743]: smartd is exiting (exit status 0) Jul 6 22:56:42 909I7 hcid[8749]: Got disconnected from the system message bus Jul 6 22:56:42 909I7 auditd[8430]: The audit daemon is exiting. Jul 6 22:56:42 909I7 kernel: audit(1341640602.922:344412): audit_pid=0 old=8430 by auid$ Jul 6 22:56:43 909I7 pcscd: pcscdaemon.c:572:signal_trap() Preparing for suicide Jul 6 22:56:43 909I7 pcscd: hotplug_libusb.c:376:HPRescanUsbBus() Hotplug stopped Jul 6 22:56:44 909I7 pcscd: readerfactory.c:1379:RFCleanupReaders() entering cleaning f$ Jul 6 22:56:44 909I7 pcscd: pcscdaemon.c:532:at_exit() cleaning /var/run Jul 6 22:56:44 909I7 kernel: Kernel logging (proc) stopped. Jul 6 22:56:44 909I7 kernel: Kernel log daemon terminating. Jul 6 22:56:45 909I7 exiting on signal 15

  Read the article

• Will this RAM work well in an iMac?

  - by sala_7

  I want to increase the RAM of my 2.4GHz Intel Core 2 Duo 24" iMac. I currently have 1GB of RAM DDR2 SDRAM 667 MHz. I really want to upgrade, but know nothing about RAM or hardware in general... These are the cards I found: http://www.crucial.com/eu/store/mpartspecs.aspx?mtbpoid=D4B6F603A5CA7304 Are these of quality or should I look at something else? Finally, I have 800MHz of Bus speed, couldn't I get faster RAM? Thanks for taking the time to read, and hoping you take the time to answer.

  Read the article

• What hardware factors may be considered bottlenecks on a Hyper-V virtual server during load testing?

  - by sean

  Our organization is load testing our application using virtual servers via Hyper-V to see what the user load can be using fair equipment on a single box setup. The developer group questioned the validity of the tests given the normal use of the box by the other virtual machines. IT admins answered that it is an acceptable platform to load test on because it has its own CPUs, memory and disks allocated. Is their answer mostly correct? What hardware factors may be considered bottle necks given the other virtual machines when testing our application? For example, would bus speed be a concern or network IO? The application consists of a windows service written using the 4.0 .NET Framework and SQL Server 2008 R2.

  Read the article

• Real RAM latency

  - by user32569

  Hi, very quick question. When I look for RAM timing, I got 2 different explanations on what is CAS latency. First states, its the time after command to read has been issued from CPU and data are send to data bus. Second says its time betwen column in memory layout has been activated. So, where is the truth? I mean, when I want to know total RAM latenci, in case 1, ot would be just CAS times one clock time. In second case, it would be CAS+other things like RAstoCAS and so times one clock time. Thanks.

  Read the article

• Removing integrated video card drivers broke other hardware?

  - by jsnlxndrlv

  I just purchased and installed an XFX ATI Radeon HD 4650 video card. The installation instructions said to remove the old video card drivers before installing the new driver. I did both things, but now every time I start my computer, the Found New Hardware wizard pops up for the following three devices: PCI Device SM Bus Controller Other PCI Bridge Device Furthermore, my LAN port no longer functions. The cable's connected, and the light on the port comes on, but the computer can't find any servers when I attempt to connect with it. The modem and router are working, and obviously I'm able to use the other computer here to post this. What do I do to fix this?

  Read the article

• How to use a D-Link usb network adapter on debian

  - by Barranka

  I have a Debian (squeeze) desktop, and I need to use a D-Link 150 USB Wireless Network Adapter. So far I've done this: $ lsusb ... Bus 001 Device 006: ID 2001:3c18 D-Link Corp. ... After looking for a solution in google, I found that I needed to install the following package: firmware-ralink_0.28+squeeze1_all.deb I've installed it, but Debian doesn't want to find the adapter. When I run lsmod, I can't find what I'm supposed to find: rt2870sta Can you point me in the right direction?

  Read the article

• Assembling a number-crunching computer [closed]

  - by tugrul büyükisik

  What is needed to make a GPU fully fed by CPU? Comparing their flops/s is enough? For example, if i could manage to make a very old(pentium-3) CPU with one of Nvidia-Fermi GPU, it would not be able to fed the gpu with data per sec. What is the criteria to fit CPU to GPU exactly when OpenCL or some similar work needed? Of course RAM and BUS will be chosen in a similar way but how exactly? Assume each GPU-core will calculate a sqrt and a division and an adding for 100 times for every itearation. Thanks.

  Read the article

< Previous Page | 472 473 474 475 476 477 478 479 480 481 482 483  | Next Page >