Search Results

Search found 1461 results on 59 pages for 'equipment recommendation'.

Page 48/59 | < Previous Page | 44 45 46 47 48 49 50 51 52 53 54 55  | Next Page >

• VMware NAS/iSCSI recommendations - smallish organization

  - by Bubnoff

  I have two VMware servers - ESX + ESXi. Two backup NAS boxes. The current NAS boxes are low-cost and unsuitable for running VMs from. Support NFS only. Slow. My plan is to have a dedicated iSCSI/NAS for storing and running VMs. Two additional low-cost boxes for backup. I'm looking for advice regarding 2 things really: Recommendations as far as VMware architecture/design for a smaller organization. Less than 20 Virtual Machines. 2 servers + 2 x 1.5 terabyte backup NAS boxes. A good NAS/iSCSI box with your recommendation on RAID config ...I would go with 6 or better. I'm trying to design an installation that is both fast and reliable/redundant. If you have any experiences to share or your current configuration including network design ( switches, fiber ...etc ), I will be enormously thankful. I'm not married to this idea, so if you have a design not using iSCSI NAS boxes ...let er rip. Cost? Can we stay around $5,000 ( on top of already stated components )? Links to info are welcome also. Thanks for reading! Bubnoff

  Read the article

• outlook security alert after adding a second wireless access point to the network

  - by Mark

  Just added a Netgear WG103 Wireless Access Point in our conference room to allow visitors to access the internet through out internal network. When switched on visitors can connect to the intenet and everything works fine. Except, when the Access Point is switched on, normal users of the network get a Security Alert when they try to start Outlook 2007. The Security Alert is the same as the one shown in question 148526 asked by desiny back in June 2010 (http://serverfault.com/questions/148526/outlook-security-alert-following-exchange-2007-upgrade-to-sp2) rather than "autodiscover.ad.unc.edu" my security alert references our "Remote.server.org.uk". If I view the certificate it relates to "Netgear HTTPS:....", but the only Netgear equipment we have is the new Access Point installed in the conference room. If the Access Point is not switched on we do not get the Security Alert. At first I thought it was because we had selected "WPA-PSK & WPA2-PSK" Network Authentication Type but it continues to occur even if we opt for "Shared Key" WEP Data Encryption. I do not understand why adding a Netgear Wireless Access point would cause Outlook to issue a Security Alert when users try to read their email. Does anyone know what I have to do to get rid of the Security Alert? Thanks in advance for reading this and helping me out.

  Read the article

• Will wear induced by turning computers off in the evening be offset by energy savings?

  - by sharptooth

  I'm asking this here because this is primarily a huge office scenario and administrators will more likely have the answer I'm looking for. Employees' desktop computers can be either left turned on for the whole night or switched off in the evening and turned back on in the morning. The latter will surely save energy. In the same time turning on and off is very harmful for the equipment - hardware often breaks specifically when turned on. Both energy and hardware replacements cost money. With energy it's quite obvious - you pay every month according to what your power meter shows. With hardware replacements it's worse - you need qualified stuff to quickly diagnose the problems and once something breaks the affected employee will have to wait for some time while his computer is fixed/replaced and the data is recovered. So the company has to choose between saving money on energy and saving money on computer maintaince and lost hours. Such decisions must be well though. Is there any detailed study of how turning computers off each evening affects their lifetime?

  Read the article

• Do eSATA HDD docking stations have a capacity limit?

  - by Michael Kjörling

  I'm looking at perhaps buying an eSATA docking station to be able to easily plug in and unplug hard disk drives, particularly but not necessarily only for backup purposes. Note: This is not a hardware shopping recommendation question. Please don't vote to close it as such. Looking at different models, I find for example this page detailing the Deltaco SI-7908SUS which specifically states "storage capacity: 1.5 TB" as well as "pictured hard disk not included, only for illustration". A customer review specifically mentions that it does not work with 3 TB drives, although does not go into any detail such as OS, drive model, etc. From a brief glance, the vendor's web site does not appear to say either way. Then there is the quite similar Deltaco SI-7908B3 which boasts on the box "all 2.5" and 3.5" HDD/SSD compatible". My question is: Why would what basically amounts to a SATA/eSATA adapter have any say in what storage capacity devices are supported? Does it? Assuming the OS supports the full capacity of the drive, why should introducing another (not even a different, really) connector change anything? Bonus question: Might it make a difference if the docking station exposes multiple interfaces (such as in the case of for example the SI-7908SUS exposing USB 2.0 and eSATA)? (I still think it shouldn't, but it'd be nice to have it confirmed.)

  Read the article

• How far should we take the N+N redundancy craziness ?

  - by Brann

  The industry standard when it comes from redundancy is quite high, to say the least. To illustrate my point, here is my current setup (I'm running a financial service). Each server has a RAID array in case something goes wrong on one hard drive .... and in case something goes wrong on the server, it's mirrored by another spare identical server ... and both server cannot go down at the same time, because I've got redundant power, and redundant network connectivity, etc ... and my hosting center itself has dual electricity connections to two different energy providers, and redundant network connectivity, and redundant toilets in case the two security guards (sorry, four) needs to use it at the same time ... and in case something goes wrong anyway (a nuclear nuke? can't think of anything else), I've got another identical hosting facility in another country with the exact same setup. Cost of reputational damage if down = very high Probability of a hardware failure with my setup : <<1% Probability of a hardware failure with a less paranoiac setup : <<1% ASWELL Probability of a software failure in our application code : 1% (if your software is never down because of bugs, then I suggest you doublecheck your reporting/monitoring system is not down. Even SQLServer - which is arguably developed and tested by clever people with a strong methodology - is sometimes down) In other words, I feel like I could host a cheap laptop in my mother's flat, and the human/software problems would still be my higher risk. Of course, there are other things to take into consideration such as : scalability data security the clients expectations that you meet the industry standard But still, hosting two servers in two different data centers (without extra spare servers, nor doubled network equipment apart from the one provided by my hosting facility) would provide me with the scalability and the physical security I need. I feel like we're reaching a point where redundancy is just a communcation tool. Honestly, what's the difference between a 99.999% uptime and a 99.9999% uptime when you know you'll be down 1% of the time because of software bugs ? How far do you push your redundancy crazyness ?

  Read the article

• Is a Hyperthreaded CPU more powerful and more efficient than a Dual-core CPU? [closed]

  - by user1811864

  which computer to choose with Pentium processor hello they are getting rid of the old computer equipment in the office and i have to choose the computer to take home i get first choice to pick. -15 inch lcd screen 4 gb of ram core 2 duo dual Core E8400 3.00 GHz dvd writer windows vista/ linux -15 inch crt monitor with 2 gb ram and pentium 4 2 ghz single core HT technology windows xp hardisks both 250 GB my friend is telling me to choose the second one Pentium single core HT because he told me it runs faster becuase of HT technology and cooler and consumes less current electricity so it wont get overheated because it has HT technology so it's high definition for encoding and watching HD movies and HD sound and is like a gaming pc to play internet games. And also he said the dual core 8400 runs at 3 ghz compared to the 2 ghz so it heats very much because of the two extra cores so it takes more current raising electricty bills and is not good for gaming and watching HD movies and internet flash animations and games because of getting heated everytime. And he wants to choose and take the E8400 because he has air conditioning at home so it will be safe from heating. So which one computer should i take is it really faster because of the HT High definition technology and will i be able to play internet flash card games better and watch good HD movies Youtube etc and play all the music and songs.

  Read the article

• VLAN Through Switch Doesn't Work

  - by vcsjones

  I have the following scenario: I have a Cisco Aironet 1040 access point. I have it configured with two SSIDs, each going to a different VLAN. So: SSID internal : VLAN 90 SSID guest : VLAN 70 On the router side, I have a Cisco RV220W (with the radios now turned off) and have setup VLANs with like VLAN IDs. VLAN 90 : 192.168.90.0/24 VLAN 70 : 192.168.70.0/24 As far as DHCP is concerned, each VLAN has a "DHCP Server" in the router's configuration: So with the access point connected directly to the router, everything works great. I connect to the internal network, and I get a 192.168.90.x address, and the guest network gets a 70.xxx address. Next I introduced a Cisco SG200-50 PoE switch between the router and the access point. The port is configured as a trunk port, so the VLAN tags should go right through the switch back to the router. However, when something is connected to the access point, nothing works. It isn't able to get an IP address, and manually assigning one doesn't seem to let any traffic route. Given that the access point works correctly when connected to the router directly, I believe the switch is misconfigured. What am I missing here? What can I use to better diagnose what the problem might be? It's small business equipment, so CLI access is not available. Below are screenshots of the switch's config. The access point is connected to GE2.

  Read the article

• Can I share my cable internet connection through my ADSL wireless router?

  - by Roaders

  Hi All Over the xmas period I am at my in-laws. They have Virgin Broadband (cable) and have a basic modem / router that is plugged directly into their computer using an ethernet cable. My wife and I arrived with 5 PCs! (ok, one is a gift and won't be used) 4 of which are laptops so I would like to be able to use their internet connection. At the moment I am working so have plugged the ethernet cable into my work laptop. Rebooting the router meant that my work laptop now has internet. I have my ADSL Netgear router which is wireless. I tried plugging it in between the router and the PC but I didn't seem to be able to share the internet connection wirelessly. The original PC still had internet despite ony being connected to my router but my wireless laptop didn't have a connection. My old cable router had an internet ethernet port on the back that the modem plugged into. My ADSL router doesn't, it has a phone connection socket. Is there a way of doing what I want with the equipment I have? Thanks

  Read the article

• Regarding AD Domain controllers and remote branch offices

  - by Alex

  We have central HQ building and a lot of small branch offices connecting via VPN and want to implement AD (If you can believe we still haven't). We want everyone to log in using domain accounts and be policed centrally. We are OK with having a RODC in a branch office with like 10 computers. But we have these small branches with two to four PCs only. Some of these branches connect to HQ via IPSec site-to-site VPN, some via remote access (client-based) VPN. So there is no problem with ones that have local RODC or connecting to HQ DCs via VPN router. But how about small branches? We don't really want to set up a machine there, neither we want to invest into Windows Server licenses or fancy network equipment. Also, the problem is that we cannot access HQ DCs via VPN because we are not logged in and connected to HQ internal network yet, so DCs aren't reachable. What is typically done in that situation if it is needed to have central management over policies on those PCs? Or is it better to let 'em loose and use local policies and accounts in this situation?

  Read the article

• Privacy, VPN and routers

  - by user123189

  Ever since this ACTA push-up the things are starting to heat up around torrents and privacy. I am using Tribler now, but this is not secure enough for me. Not enough privacy. I've been using in the past a swedish VPN PPTP connection. What I observed is that, when the VPN connection was down, Internet traffic wasn't cut off, rather the downloads were continuing, this time with my real IP, wearing off my protection. 1st : How to enforce a VPN connection that will cut all traffic when down? That is, the moment the connection is down, all internet traffic should cease as if I'd pull the network plug out. 2nd: Is PPTP good enough or should I ask for SSTP or IKEV2 ? 3rd: Should I disable IPv6 ? Is VPN no longer private if I keep IPv6 active? I 'heard some stuff' about dual vpn routers to be able to improve privacy; but nothing more about how to configure one for such a task. 4th: Is there any kind of "black box" hardware equipment that can be used in hiding IP, encrypting traffic and so on ?

  Read the article

• Looking for suggestions for hosting Windows 2000 Server in the cloud / VPS / etc?

  - by JohnyD

  I have a Windows 2000 Server, currently virtualized in Hyper-V, that I would like to get running off-site as a backup (cloud, VPS, etc). You can't virtualize in EC2 and I'm fairly certain there are no Server 2000 AMI's floating about (correct me if I'm wrong!). If anyone has a recommendation on how I can get a virtualized Windows 2000 Server running in a secure, remote environment I would be grateful. As far as locations go I'd be interested in both North America as well as Australia and Europe. In a nutshell, we're ploughing our way out of a legacy codebase and this server is the last that remains of the legacy apps. However, it is still very much used by our clients. Everything is backed up each night (data, images, etc) to tape which is then taken offsite. However, in the event of a fire I would love to have a backup legacy server to point DNS records to. So while I am rebuilding from the ashes our services would already be available. It would save a lot of time and make my managers all the more happy (and that's what it's all about, riighhtt? :D) Thank you all for your suggestions. Please let me know if I've left out any important information. Additional info: - the legacy codebase does not function properly in Server 2003

  Read the article

• Simple vLAN setup

  - by Logan Bissonnette

  I have a basic lab environment set up to try and get 2 vLANs working in hyper-v. I have the following equipment 1 hyper-v server 1 Desktop PC 1 Managed Switch (d-link DES-3052P) 1 cheap router (DI-604) My end goal is to have 1 VM and the desktop on one vLAN with internet, and 1 VM on a separate vLAN with internet access. I am having troubles getting an internet connection to both vLANs. The switch does not have the ability to have asynchronous vLANs. This is my switch configuration Port 1 - Trunk Port - Connected to router Port 2 - Trunk Port - Connected to hyper-v Server Port 3 - Access Port- Connected to Desktop Within hyper-v I have 1 switch and 2 VMs. When the VMs are set up to use vlan ID 1, everything works fine. As soon as a VM is set up to use vlan ID 2, they lose all network connection and cannot communicate with the router anymore. I believe this is because the router is not vLAN aware. Can anyone help me with what settings need to be set up on my switch? I believe I want an egress rule so traffic leaving towards the router is untagged, is that right? If not, any ideas or hints as to what needs to be set up?

  Read the article

• USB question (how durable is it, how should I workaround this)

  - by Shiki

  The plot is quite simple. Got a Razer mouse. If I plug it in, it works. After a shutdown/hibernation, I have to replug it entirely at the back of the PC. (It works in my laptop even after severel shutdown, etc, so yes I guess it's my motherboard.. but it still got 2 years of warranty and it comes with quad SLI, its not an old motherboard at all. (MSI P7N SLI FI (bought it after a hungarian guy's recommendation)). So. I only could come up with one "solution". Get 3 USB cable (you know, USB-USB). If its possible the shortest ones (don't know if the responsibility/anything will worsen), AND replug only the middle+closest to the USB port junction, since those are replaceable. What do you think? Any other idea? (BIOS is updated, mouse driver ... doesn't really matter, the mouse won't even blink a bit after this happens. It lights up and goes totally dead.)

  Read the article

• How can I change the binding order of network adapters in Windows 7?

  - by Chris Farmer

  The end goal here is that I am trying to install an Oracle 10g server on my Windows 7 x64 dev box. I use DHCP, and the Oracle installer is throwing up this warning: Checking Network Configuration requirements ... Check complete. The overall result of this check is: Failed <<<< Problem: The install has detected that the primary IP address of the system is DHCP-assigned. Recommendation: Oracle supports installations on systems with DHCP-assigned IP addresses; However, before you can do this, you must configure the Microsoft LoopBack Adapter to be the primary network adapter on the system. See the Installation Guide for more details on installing the software on systems configured with DHCP. I have installed the loopback adapter, but I am not sure how to make it the primary network adapter. I see this Microsoft KB article on the subject but it's Windows XP-oriented, and I can't seem to find a comparable one for Windows 7. Some of the options it talks about don't seem to be present in the views of the adapters that I see. So, how can I make the loopback adapter become the primary adapter?

  Read the article

• Freebsd jail for an small company - checklist - what shouldn't forget

  - by cajwine

  Looking for an checklist for an "small company freebsd/jail server". Having pretty common starting point: FreeBSD jail (remote/headless) for the company: public web, email, ftp server, and private (maybe in the future partially public) wiki (foswiki) 4 physical persons, (6 email addresses) + one admin - others will never use ssh) have already done usual hardening on the host side (like pf, sshguard etc). my major components are: dovecot, exim, apache22, proftpd, perl5.14. Looking for an checklist, what I shouldn't forget. My plan: openssl self-signed certificates for exim, dovecot and proftpd (wildcard keys) openssl self-signed certificate for apache (later will go for "trusted-signed" key) My questions are: is is an "good practice" having one pair of wildcard SSL-certificates for many programs? (exim, dovecot, proftpd) - or should I generate one key for each service? should I add all 4 persons as standard (unix) users, or I should go with virtual users? Asking because: have only small count of users, and it is more simple to configure everything (exim, dovecot) for local users ($HOME/Maildir), plus ability to set $HOME/.forward/vacation and etc. is here some (special) things what I should consider? (e.g. maybe, in the future we want setup our own webmail - will make this any difference?) any other recommendation? Thank you, hoping that this question fit into the http://serverfault.com/faq under the: Server and Business Workstation operating systems, hardware, software Operations, maintenance, and monitoring Looking for an checklist, but please explain why you're recommending it. See Good Subjective, Bad Subjective. related: What's your suggested mail server configuration for a FreeBSD server?

  Read the article

• Unable to connect to server after a certain amount of time

  - by Troy

  I am a business FIOS subscriber with 5 static IPs. I have the following network setup: Verizon provided ONT Dlink switch Dell server running Ubuntu 12.04 with iptables enabled and a static IP address. The makes/models of hardware are: FIOS ONT Alcatel-Lucent I-211M-H ONT D-Link D-Link Web Smart Switch DES-1228P Server Dell Optiplex 755 (Ubuntu 12.04 Server) I have iptables running on the server with http, https and ssh ports open. I can connect to a website on the server from an external computer, but after a certain amount of time (mins to hours), I can no longer connect. All I have to do to re-enable connectivity is connect to the server via SSH from a computer INSIDE the network. I don't have to actually login, I just have to establish a connection. I can then access the website externally again. I did some googling and it seems some of verizon's equipment had an ARP bug where the ARP entries would expire after a certain time period, but those issues all seem to be from back in 2009 - 2010. I know the switch has an 'auto learning Mac address' feature, but I'm not sure if that could be the problem or not. Does anyone have any ideas or advice on how I can troubleshoot this? Thanks!

  Read the article

• Why are ISP's installing routers on my site when the feed is a form of ethernet already?

  - by Cosmin Prund

  I'm connected to 3 ISP's right now. Two of them already have routers at my site, the third one announced me "they need to install some equipment" when I requested BGP session. I can only assume they need to install a Router, since that connection is now working fine, using the usual /30 net block for the connection, and the "last-mile" solution is not going to change since they only installed it last week and the BGP was in the contract from the beginning. I simply don't understand this: the "feed" is already a form of ethernet. Even those they're using different technologies for the last mile, they're all entering the ISP router using an RJ45 WAN port. I assume the ISP router does something really important that can't be done by the Big Router on the other end of the connection. It must also be something that can hurt them if miss-configured, since they don't trust us (the client) to do the stuff on our router. And I'm not talking cheap throw-away routers here: One of the routers is Cisco 2800. Edit to add network details: I'm connected to 3 ISP's, two over Radio links, one over Fiber Optic. One of the radio links is going to get dropped and the other radio link will be turned into fiber sometime next year. The fiber is 20 Mbit, radio 1 is 40 Mbit and radio 2 is 2 Mbit. I've got a /24 of provider independent address space. I'm not doing out-of-the ordinary stuff with my network, I'm overly connected because my network needs to be "up" all the time.

  Read the article

• Photoshop CS5 performance over network drive (cifs)

  - by grub

  Hello Everyone I did install a QNAP NAS TS410 for a customer (professional photographer) with 3 Hitachi Deskstar 7200rpm 2TB disk configured as RAID5. The NAS and the workstations are connected over a Gigabit network. He and his co-worker are accessing the photos (about 1TB of photos) over a mapped network drive from their windows machines (Windows XP - 32bit and Windows 7 Ultimate - 32bit). Both are using Photoshop CS5 to edit the photos. The problem is that to save a edited photo takes a really long time, it takes about 3 times as long to save a photo as to open it. After some tests I can exclude the network, the NAS and the windows machines as source of the issue. I think the problem is the Photoshop software and its handling of the network drives. Officially network drives are not supported by Adobe. I do not have any experience with the Adobe products, especially with Adobe Photoshop CS5. What are your recommendation to solve the performance issue? Should my customer copy the photos to the local drive, edit them and upload them again to the network drive or is Adobe Drive or Adobe Version Cue the answer? One requirement is that the photos need to be accessible / editable from both computers even when one of them is offline. Adobe Version Cue needs a dedicated service running to be usable, so this solution is not possible as far as I understand the Cue software. Thank you for your input to this issue and have a nice day :-) Greetings grub

  Read the article

• RouterLess, house-wired network using multiple powerline adapters

  - by Cliff Arnell

  related to the 'old days' of one ethernet cable tapped with Ts for each monitor.... my question might be very simple... or not. I have an over-the-air internet provider with a wire dish with a powered transceiver and cat5 cable out of the providers supplied modem. I'm presently connecting the output of the modem into my wireless router which sends the internet signal all over the house. Standard stuff, I believe. My Question. Can I just connect the output of the modem into 1 powerline adapter and tie all my equipment such as computer, printer, laptop, Tivo recorder, etc. into 1-each local powerline adapters located near each devices resulting in a 'house-wired' network and no router? I'm bothered by the idea that my over-the-air provider might be using something in my router to establish and keep my IP connection alive. I did have to configure the router for my IP, a router which, in my proposed scenario, would no longer exist. Thank you for your help.

  Read the article

• MySQL (local) owner and permissions

  - by Steve Nelson

  I asked this question on the MySQL forums and got no answer. I asked on StackOverflow and received a recommendation to try on ServerFault. So here I am. I recently successfully installed the 64 bit version of mysql-5.5.8 on a MacBook Pro in the /usr/local directory. To address a completely unrelated software (RVM actually) , I chown-ed my /usr/local directory to $USER, Which made MySQL very unhappy. It complained specifically about the /usr/local/mysql/data directory, so I chown-ed that directory to _mysql:wheel. Everything appears to work again, but it made me wonder if I would have been better off changing the owner of the whole /usr/local/mysql directory, not just the data subdirectory. Since I neglected to make notes of what owner the default installation runs under before rashly changing the owner of the /usr/local directory, could someone tell me what owner and permissions the /usr/local/mysql directory is by default if you don't inadvertently screw it up? :-/ In terms of permissions I'm guessing rwxr-xr-x would be appropriate (that's what the data directory currently has and it appears to be working fine), but reinforcement for that hunch would be appreciated. Thanks for any help. Steve

  Read the article

• Where did my backup files go? Can they be recovered?

  - by Ken

  I just purchased a Western Digital Essential SE 1TB external hard drive from Best Buy at their recommendation. I then exchanged it for a Toshiba Canvio (I think that was the name). I have a Toshiba Qosmio X505-Q898. The Canvio locked up my computer and rewrote some kind of OS file, and erased all the restore points as well as the system image backup (according to Best Buy) just by plugging it in for the first time. Never even got to the install part or anything -- plugged it in and fried my computer. They spent about an hour and a half on my computer and got it back to a somewhat working condition and gave me access to my files. So now they say I have to back it up using my recovery disk and rewriting my OS. Enter the Essential. Brought it home last night, plugged it in and installed everything. Works perfect, no problems. Backed up everything on it. I unplugged and plugged it twice to make sure that everything was on it. Essential told me it had both the HDD and SSD backed up. So I reinstalled my OS. Plugged the Essential in and everything loads right up. Went to retrieve my files and the Western Digital has nothing on it. It shows all my music, pics, ETC. as still being on my computer and needing to be backed up, but since there are no files on my computer now. Where is this information coming from and where did my files go? It's about 810GB worth of files I've amassed over several years. Is there any way to recover data from this? I plan to contact Western Digital and Best Buy, just thought I would check here too. Any advice will be appreciated as a lot of these files are invaluable to me.

  Read the article

• What format should I convert my iTunes Videos to?

  - by Aequitarum Custos

  Recently got Daniusoft Media Converter, and was about to strip the DRM off my iTunes library, then I found I had a huge decision to make. Converting my music seems obvious, to MP3, however the video formats, I'm at a loss on. It has "optimized" formats for all types of video players such as iPhone, Zune, Droid (which I own), and just a huge list! I bought several seasons of House and a few movies, though I don't know which format would be optimal to not lose quality. While I love my Droid, I have no intention on watching full episodes or movies on it, and I have a feeling that would reduce quality. One of the options sections is HD Video, and it has HD MPEG-4 Video (*.mp4). That one seems like it would be the best format to convert to without losing quality, but again, I'm unsure. Has anyone used this software, or have general expertise in video formats to give a recommendation on what file format I should convert my videos to? Format requirements: No loss in quality Portability would be ideal (as in, will play on my Windows and potentially MAC, and streamable to a bigscreen).

  Read the article

• Reading email from Emacs VM using a secure server (Gmail)

  - by Alan Wehmann

  This is a question (see below) originally entered at https://answers.launchpad.net/vm/+question/108267 and upon the recommendation of Uday Reddy the question and answers are being moved here. The date of the original question was May 4, 2010. One subject of the question is use of the program stunnel with program View Mail (run within Emacs) on a PC running Microsoft Windows, in order to read email from a server that requires use of TSL/SSL (Gmail). See the related question, How to configure Emacs smtp for secure server for using a secure server, for sending email. The programs discussed are Emacs, VM (ViewMail) and stunnel. The platform under discussion is MS Windows. The original question was asked by usr345 on 2010-04-24: I tried to install vm on Windows, but when I tried to get the mail from gmail using ssl, an error emerges, emacs hanges-up. Here is the code from .emacs: (add-to-list 'load-path (expand-file-name "~/vm/lisp")) (add-to-list 'Info-default-directory-list (expand-file-name "~/vm/info")) (require 'vm-autoloads) (setq vm-primary-inbox "~/mail/inbox.mbox") (setq vm-crash-box "~/mail/inbox.crash.mbox") (setq vm-spool-files `((,vm-primary-inbox "pop-ssl:pop.gmail.com:995:pass:usr345:PASSWORD" ,vm-crash-box))) (setq vm-stunnel-program "g:/program files/stunnel/stunnel.exe") So, the question: How to configure pop-ssl on Windows?

  Read the article

• DNS manager in Windows Server 2012 Essentials - My one server appears twice

  - by tetranz

  I have a newly installed Windows Server 2012 Essentials. It works pretty good although I'm working on some DNS improvements. Something that seems a little weird is in DNS Manager, my server appears twice. Once as hostname and once as hostname.mydomain.local. They seem to be identical and locked in sync. If I change one, the other follows. Is this normal? Does anyone know why I have this? I'm talking about the top level on the navigation. The very top is DNS and then these two below. Zones, forwarders etc are below them. I've found a couple of forum posts of people asking the same thing but no useful answer. All tutorials etc I can find with screenshots show only one which makes me uncomfortable. The server was installed out of the box as standard with the wizards. I know about the recommendation not to use .local but the wizards didn't give me any other option.

  Read the article

• Can't see more than the first few lines in an SSH connection

  - by hello

  I need some help for SSH buffer size. I have a vista machine at home and i have installed "Free SSHD" on it. I also have Dynamic DNS setup to access some of my home lab equipment which are connected to this vista machine. From my work machine which is an XP machine I connect to my home machine using Putty. Everything up to this point is working fine without any problem. The issue is I can't see more lines than the first few lines of the output. I press the space bar to get more output off the screen and the output scrolls up and it gets lost as the more output gets displayed on the screen. The Putty client i am using on my work machine has been setup with enough buffer size but the output still only displays few lines and as it moves up, the buffer gets empty automatically. I have searched the entire web and haven’t found any proper solution any where. Can someone please help here? Thanks.

  Read the article

< Previous Page | 44 45 46 47 48 49 50 51 52 53 54 55  | Next Page >