Search Results

Search found 1217 results on 49 pages for 'jack yuan'.

Page 48/49 | < Previous Page | 44 45 46 47 48 49  | Next Page >

• Integrated webcam in lenovo t410 not working with 12.04

  - by kristianp

  I have a Lenovo T410 with an inbuilt webcam and I haven't been able to get the webcam working. I tried skype, cheese, both just give me a black window. The microphone works fine with skype, by the way. Can anyone provide any clues please? The webcam is enabled in the bios, but there is no light indicating the webcam is on (not sure if there should be, though). I tried this on Kubuntu 11.10 and have upgraded to 12.04 with the same results. The Fn-F6 keyboard combination doens't seem to do anything either. EDIT: I got the webcam replaced, it looks like it was a hardware problem, because it works fine now. Thanks guys. $ ls /dev/v4l/* /dev/v4l/by-id: usb-Chicony_Electronics_Co.__Ltd._Integrated_Camera-video-index0 /dev/v4l/by-path: pci-0000:00:1a.0-usb-0:1.6:1.0-video-index0 And lsusb: $ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 147e:2016 Upek Biometric Touchchip/Touchstrip Fingerprint Sensor Bus 001 Device 004: ID 0a5c:217f Broadcom Corp. Bluetooth Controller Bus 001 Device 005: ID 17ef:480f Lenovo Integrated Webcam [R5U877] Bus 002 Device 003: ID 05c6:9204 Qualcomm, Inc. Bus 002 Device 004: ID 17ef:1003 Lenovo Integrated Smart Card Reader Here is the output from guvcview, minus lots of lines describing the available capture formats. It says "unable to start with minimum setup. Please reconnect your camera.". guvcview 1.5.3 ALSA lib pcm_dmix.c:1018:(snd_pcm_dmix_open) unable to open slave ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.rear ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.center_lfe ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.side ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib pcm_dmix.c:957:(snd_pcm_dmix_open) The dmix plugin supports only playback stream ALSA lib pcm_dmix.c:1018:(snd_pcm_dmix_open) unable to open slave Cannot connect to server socket err = No such file or directory Cannot connect to server socket jack server is not running or cannot be started video device: /dev/video0 Init. Integrated Camera (location: usb-0000:00:1a.0-1.6) { pixelformat = 'YUYV', description = 'YUV 4:2:2 (YUYV)' } { discrete: width = 640, height = 480 } Time interval between frame: 1/30, .... { discrete: width = 1600, height = 1200 } Time interval between frame: 1/15, vid:17ef pid:480f driver:uvcvideo checking format: 1196444237 libv4l2: error setting pixformat: Device or resource busy VIDIOC_S_FORMAT - Unable to set format: Device or resource busy Init v4L2 failed !! Init video returned -2 trying minimum setup ... video device: /dev/video0 Init. Integrated Camera (location: usb-0000:00:1a.0-1.6) { pixelformat = 'YUYV', description = 'YUV 4:2:2 (YUYV)' } { discrete: width = 640, height = 480 } .... vid:17ef pid:480f driver:uvcvideo checking format: 1448695129 libv4l2: error setting pixformat: Device or resource busy VIDIOC_S_FORMAT - Unable to set format: Device or resource busy Init v4L2 failed !! ERROR: Minimum Setup Failed. Exiting... VIDIOC_REQBUFS - Failed to delete buffers: Invalid argument (errno 22) cleaned allocations - 100% Closing portaudio ...OK Terminated.

  Read the article

• ArchBeat Link-o-Rama for 2012-06-26

  - by Bob Rhubart

  Software Architecture for High Availability in the Cloud | Brian Jimerson Brian Jimerson looks at the paradigm shifts from machine-based architectures to cloud-based architectures when designing fault tolerance, and how enterprise applications need to be engineered to ensure the highest level of availability in the cloud. SOA, Cloud & Service Technology Symposium 2012 London - Special Oracle Discount Registration is now open for one of the premier SOA, Cloud, and Service Technology events. Once again, the Oracle community is well-represented in the session schedule. And now you can save on registration with a special Oracle discount code. Progress 4GL and DB to Oracle and cloud | Tom Laszewski "Getting from client/server based 4GLs and databases where the 4GL is tightly linked to the database to Oracle and the cloud is not easy," says cloud migration expert Tom Laszewski. "The least risky and expensive option...is to use the Progress OpenEdge DataServer for Oracle." Embrace 'big data' now or fall behind the competition, analyst warns | TechTarget TechTarget's Mark Brunelli's story says, in essence, that Big Data is not your fathers Business Intelligence. Calculating the Size (in Bytes and MB) of a Oracle Coherence Cache | Ricardo Ferreira Ferreira illustrates a programmatic way to use the Oracle Coherence API to calculate the total size of a specific cache that resides in the data grid. WebCenter Portal Tutorial Part 7: Integrating Discussions and Link service | Yannick Ongena The latest chapter in Oracle ACE Yannick Ongena's ongoing series. How to Setup JDeveloper workspace for ADF Fusion Applications to run Business Component Tester? | Jack Desai Helpful technical tips from yet another member of the Oracle Fusion Middleware Architecture Team. Big Data for the Enterprise; Software Architecture for High Availability in the Cloud; Why Cloud Computing is a Paradigm Shift - And Why It Isn't This week on the OTN Solution Architect Homepage, along with an updated events list and this weeks list of selected community blog posts. Worst Practices for Big Data | Dain Hansen Dain Hansen shares some insight on what NOT to do if you want to captialize on Big Data. Free Virtual Developer Day - Oracle Fusion Development | Grant Ronald "The online conference will include seminars, hands-on lab and live chats with our technical staff including me!" says Grant Ronald. "And the best bit, it doesn't cost you a single penny. It's free and available right on your desktop." Penguin is Getting Ready for Oracle OpenWorld 2012 | Zeynep Koch Linux fan? Check out Zeynep Koch's post for a list of Linux-based sessions at Oracle OpenWorld 2012 in San Francisco. Amazon Web Services (AWS) Autoscaling | Frank Munz "Autoscaling on AWS can only be configured with lengthy commands from the command line but not from the web cased AWS console," says Frank Munz. "Getting all the parameters right can be tricky." He demonstrates one easy example in this video. Oracle Fusion Applications Design Patterns Now Available For Developers | Ultan O'Broin "These Oracle Fusion Applications UX Design Patterns, or blueprints, enable Oracle applications developers and system implementers everywhere to leverage professional usability insight," says O'Broin. How Much Data Is Created Every Minute? [INFOGRAPHIC] | Mashable Explaining what the "Big" in Big Data really means -- and it's more than a little mind-boggling. Thought for the Day "Real, though miniature, Turing Tests are happening all the time, every day, whenever a person puts up with stupid computer software." — Jaron Lanier Source: SoftwareQuotes.com

  Read the article

• How do I get my character to move after adding to JFrame?

  - by A.K.

  So this is kind of a follow up on my other JPanel question that got resolved by playing around with the Layout... Now my MouseListener allows me to add a new Board(); object from its class, which is the actual game map and animator itself. But since my Board() takes Key Events from a Player Object inside the Board Class, I'm not sure if they are being started. Here's my Frame Class, where SideScroller S is the player object: package OurPackage; //Made By A.K. 5/24/12 //Contains Frame. import java.awt.BorderLayout; import java.awt.Button; import java.awt.CardLayout; import java.awt.Color; import java.awt.Container; import java.awt.Dimension; import java.awt.Graphics; import java.awt.Graphics2D; import java.awt.GridBagLayout; import java.awt.GridLayout; import java.awt.Image; import java.awt.Rectangle; import java.awt.event.ActionEvent; import java.awt.event.ActionListener; import java.awt.event.KeyEvent; import java.awt.event.MouseAdapter; import java.awt.event.MouseEvent; import java.awt.event.MouseListener; import javax.swing.*; import javax.swing.plaf.basic.BasicOptionPaneUI.ButtonActionListener; public class Frame implements MouseListener { public static boolean StartGame = false; JFrame frm = new JFrame("Action-Packed Jack"); ImageIcon img = new ImageIcon(getClass().getResource("/Images/ActionJackTitle.png")); ImageIcon StartImg = new ImageIcon(getClass().getResource("/Images/JackStart.png")); public Image Title; JLabel TitleL = new JLabel(img); public JPanel TitlePane = new JPanel(); public JPanel BoardPane = new JPanel(); JPanel cards; JButton StartB = new JButton(StartImg); Board nBoard = new Board(); static Sound nSound; public Frame() { frm.setLayout(new GridBagLayout()); cards = new JPanel(new CardLayout()); nSound = new Sound("/Sounds/BunchaJazz.wav"); TitleL.setPreferredSize(new Dimension(970, 420)); frm.add(TitleL); frm.add(cards); cards.setSize(new Dimension(150, 45)); cards.setLayout(new GridBagLayout ()); cards.add(StartB); StartB.addMouseListener(this); StartB.setPreferredSize(new Dimension(150, 45)); frm.setDefaultCloseOperation(JFrame.EXIT_ON_CLOSE); frm.setSize(1200, 420); frm.setVisible(true); frm.setResizable(false); frm.setLocationRelativeTo(null); frm.pack(); } public static void main(String[] args) { SwingUtilities.invokeLater(new Runnable() { public void run() { new Frame(); } }); } public void mouseClicked(MouseEvent e) { nSound.play(); StartB.setContentAreaFilled(false); cards.remove(StartB); frm.remove(TitleL); frm.remove(cards); frm.setLayout(new GridLayout(1, 1)); frm.add(nBoard); //Add Game "Tiles" Or Content. x = 1200 nBoard.setPreferredSize(new Dimension(1200, 420)); cards.revalidate(); frm.validate(); } @Override public void mouseEntered(MouseEvent arg0) { // TODO Auto-generated method stub } @Override public void mouseExited(MouseEvent arg0) { // TODO Auto-generated method stub } @Override public void mousePressed(MouseEvent arg0) { // TODO Auto-generated method stub } @Override public void mouseReleased(MouseEvent arg0) { // TODO Auto-generated method stub } }

  Read the article

• Give a session on C++ AMP – here is how

  - by Daniel Moth

  Ever since presenting on C++ AMP at the AMD Fusion conference in June, then the Gamefest conference in August, and the BUILD conference in September, I've had numerous requests about my material from folks that want to re-deliver the same session. The C++ AMP session I put together has evolved over the 3 presentations to its final form that I used at BUILD, so that is the one I recommend you base yours on. Please get the slides and the recording from channel9 (I'll refer to slide numbers below). This is how I've been presenting the C++ AMP session: Context (slide 3, 04:18-08:18) Start with a demo, on my dual-GPU machine. I've been using the N-Body sample (for VS 11 Developer Preview). (slide 4) Use an nvidia slide that has additional examples of performance improvements that customers enjoy with heterogeneous computing. (slide 5) Talk a bit about the differences today between CPU and GPU hardware, leading to the fact that these will continue to co-exist and that GPUs are great for data parallel algorithms, but not much else today. One is a jack of all trades and the other is a number cruncher. (slide 6) Use the APU example from amd, as one indication that the hardware space is still in motion, emphasizing that the C++ AMP solution is a data parallel API, not a GPU API. It has a future proof design for hardware we have yet to see. (slide 7) Provide more meta-data, as blogged about when I first introduced C++ AMP. Code (slide 9-11) Introduce C++ AMP coding with a simplistic array-addition algorithm – the slides speak for themselves. (slide 12-13) index<N>, extent<N>, and grid<N>. (Slide 14-16) array<T,N>, array_view<T,N> and comparison between them. (Slide 17) parallel_for_each. (slide 18, 21) restrict. (slide 19-20) actual restrictions of restrict(direct3d) – the slides speak for themselves. (slide 22) bring it altogether with a matrix multiplication example. (slide 23-24) accelerator, and accelerator_view. (slide 26-29) Introduce tiling incl. tiled matrix multiplication [tiling probably deserves a whole session instead of 6 minutes!]. IDE (slide 34,37) Briefly touch on the concurrency visualizer. It supports GPU profiling, but enhancements specific to C++ AMP we hope will come at the Beta timeframe, which is when I'll be spending more time talking about it. (slide 35-36, 51:54-59:16) Demonstrate the GPU debugging experience in VS 11. Summary (slide 39) Re-iterate some of the points of slide 7, and add the point that the C++ AMP spec will be open for other compiler vendors to implement, even on other platforms (in fact, Microsoft is actively working on that). (slide 40) Links to content – see slide – including where all your questions should go: http://social.msdn.microsoft.com/Forums/en/parallelcppnative/threads.   "But I don't have time for a full blown session, I only need 2 (or just 1, or 3) C++ AMP slides to use in my session on related topic X" If all you want is a small number of slides, you can take some from the session above and customize them. But because I am so nice, I have created some slides for you, including talking points in the notes section. Download them here. Comments about this post by Daniel Moth welcome at the original blog.

  Read the article

• Can't remove JPanel from JFrame while adding new class into it

  - by A.K.

  Basically, I have my Frame class, which instantiates all the properties for the JFrame, and draws a JLabel with an image (my title screen). Then I made a separate JPanel with a start button on it, and made a mouse listener that will allow me to remove these objects while adding in a new Board() class (Which paints the main game). *Note: The JLabel is SEPARATE from the JPanel, but it still gets moved to the side by it. Problem: Whenever I click the button though, it only shows a little square of what I presume is my board class trying to run. Code below for the Frame Class: package OurPackage; //Made By A.K. 5/24/12 //Contains Frame. import java.awt.BorderLayout; import java.awt.Color; import java.awt.Container; import java.awt.Dimension; import java.awt.Graphics; import java.awt.Graphics2D; import java.awt.GridBagLayout; import java.awt.GridLayout; import java.awt.Image; import java.awt.Rectangle; import java.awt.event.ActionEvent; import java.awt.event.ActionListener; import java.awt.event.KeyEvent; import java.awt.event.MouseAdapter; import java.awt.event.MouseEvent; import java.awt.event.MouseListener; import javax.swing.*; import javax.swing.plaf.basic.BasicOptionPaneUI.ButtonActionListener; public class Frame implements MouseListener { public static boolean StartGame = false; ImageIcon img = new ImageIcon(getClass().getResource("/Images/ActionJackTitle.png")); ImageIcon StartImg = new ImageIcon(getClass().getResource("/Images/JackStart.png")); public Image Title; JLabel TitleL = new JLabel(img); public JPanel panel = new JPanel(); JButton StartB = new JButton(StartImg); JFrame frm = new JFrame("Action-Packed Jack"); public Frame() { TitleL.setPreferredSize(new Dimension(1200, 420)); frm.add(TitleL); frm.setLayout(new GridBagLayout()); frm.add(panel); panel.setSize(new Dimension(220, 45)); panel.setLayout(new GridBagLayout ()); panel.add(StartB); StartB.addMouseListener(this); StartB.setPreferredSize(new Dimension(220, 45)); frm.setDefaultCloseOperation(JFrame.EXIT_ON_CLOSE); frm.setSize(1200, 420); frm.setVisible(true); frm.setResizable(false); frm.setLocationRelativeTo(null); } public static void main(String[] args) { new Frame(); } public void mouseClicked(MouseEvent e) { StartB.setContentAreaFilled(false); panel.remove(StartB); frm.remove(panel); frm.remove(TitleL); //frm.setLayout(null); frm.add(new Board()); //Add Game "Tiles" Or Content. x = 1200 frm.validate(); System.out.println("Hit!"); } @Override public void mouseEntered(MouseEvent arg0) { // TODO Auto-generated method stub } @Override public void mouseExited(MouseEvent arg0) { // TODO Auto-generated method stub } @Override public void mousePressed(MouseEvent arg0) { // TODO Auto-generated method stub } @Override public void mouseReleased(MouseEvent arg0) { // TODO Auto-generated method stub } }

  Read the article

• Determining the health of a Cisco switch port?

  - by ewwhite

  I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced recently, however, the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link. We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

  Read the article

• Is my Cisco switch port bad?

  - by ewwhite

  I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced last week, however the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link (switchport configuration pastebin). We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

  Read the article

• How to install missing Sound Drivers in Ubuntu?

  - by Sakamoto Kazuma

  I seem to be missing drivers for my Gateway laptop MA7. I have looked in System-Admin-Hardware Drivers, but it does not show up in there.There are also no devices listed in Sound-Hardware. I'm guessing at this point that I don't have the driver installed. However, I get the following output: admin@machine001:~$ cat /proc/asound/cards 0 [Intel ]: HDA-Intel - HDA Intel HDA Intel at 0xd8240000 irq 22 admin@machine001:~$ And my lspci shows: 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02) 04:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 04:09.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 04:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) I have also checked alsamixer, and nothing is muted. No headphones plugged into headphone jack either. So the question now is, how do I get sound to work on my laptop? It doesn't work for any application.

  Read the article

• SQL Saturday #44 Huntington Beach Recap

  What a great day. It was long and tiring, but rewarding in so many ways. On Sunday morning, I was driving home and I decided to take the Pacific Coast Highway from Huntington Beach.  It was a great chance to exhale and just enjoy the sun and smells of the beach (I really love SoCal sometimes). And for future reference for all you speakers, the beach and ocean are only 5 minutes from the SQL Saturday location.  I just could help noticing also the shocking number of high priced cars on the road (4 Bentleys, 3 Ferraris, 1 Aston Martins, 3 Maserati, 1 Rolls Royce, and 2 Lamborghinis).  It made me think about this: Price of all those cars: $ 150,000+.  Impacting the ability of people to learn: Priceless.  We have positively impacted the education, knowledge, capabilities of not only our attendees, but also all of their companies and people they might help as well.  That is just staggering and something to be immensely proud of. To all of my fellow community leaders, I salute you. So lets talk about the event Overall We had over 220 people register for the event and had 180+ people attend the event. I was shooting for the magical 200 number, but I guess it just gives us more motivation to make it even bigger and better next time. We had a few snags along the way, but what event doesnt, but I think everything turned out great. I did not hear any negative comments and heard lots of positive comments along with people asking when the next one is going to be (More on that later). Location- Golden West College We could not have asked for a better partner for the event. Herb Cohen from Golden West College was the wizard behind the curtains. From the beginning, he was our advocate to the GWC Board and was instrumental in getting our event approved. The day off, Herb was a HUGE help getting any and all logistics that we needed taken care of. In the craziness of the early morning registration crush it was a big help knowing that he and Bret Stateham (Blog | Twitter) were taking care of testing projectors in all the rooms. Anything we needed he was there and was even proactive in getting some things that I had not even thought of (i.e. a dumpster for all of our garbage). I cannot thank Herb enough along with other members of the GWC staff including Minnie Higgins of the Career and Technical Education Division office, Jack Taylor, public safety, and Ron Pryor, Tech Services Support. And last, but not least, the Wireless on campus was absolutely FANTASTIC! Some lessons learned Unless you are a glutton for punishment, as I no doubt am, you most certainly want to give yourself more than six weeks to plan the event. I am lucky that I have a very understanding wife and had a wonderful set of co-coordinators helping me out. A big thanks goes out to Phil, Marlon (Blog | Twitter), Nitin (Twitter), Thomas (Blog | Twitter), Bret (Blog | Twitter), Ben, and Laurie. Thankfully, the sponsor and speaker community was hugely supportive and we were able to fill out the entire event with speakers and sponsors. I have to say that there is not a lot that I would change after this years event. There are obviously going to be some things that we can do better or differently next time, but overall I think it was a great event and I was more than happy with the response we received from the community. Sponsors We obviously could not have put together our event without our sponsors. So certainly have to show them some love. Platinum Sponsors Quest Software http://www.quest.com My Space http://www.myspace.com/ Gold Strategy Companion http://www.strategycompanion.com Silver Fusion-IO http://www.fusionio.com Bronze WestClinTech http://westclintech.com Professional Association For SQL Server http://www.sqlpass.org Attunity http://www.attunity.com Sharepoint 360 http://www.sharepoint360.com Some additional Thanks Andy Warren (Blog | Twitter) Always there to answer my question and help out when I had some issues or questions with the website. The amount of work that he and everyone else put into SQL Saturday is very amazing. What a great gift to the community! Einstein Bros. Bagels They were our Breakfast Vendor and arrived perfectly on time with yummy bagels, sweets and most importantly coffee. Luccis Deli (http://www.luccisdeli.com) Luccis was out Lunch Vendor. They were great to work with and the food was excellent. They worked with us to give us a great price. Heard lots of great comments about the lunches. Definitely not your ordinary box lunch. Moving Forward Unfortunately, the work does not end after the event. We have a few things to clear up such as surveys, sponsor stuff, presentations uploaded to the website, expense reimbursement, stuff like that. Hopefully, all that should be cleared up within the next couple weeks. After that as a group we are going to get together and decide what our next steps are. We definitely want to keep some of the momentum that we are building as a SQL Community and channel that into future SQL Saturdays and other types of community events. In the meantime, for additional training be sure to check out your local User Group and PASS. San Diego SQL Server Users Group ( http://www.sdsqlug.org/home/index.cfm ) Orange County SQL Server Users Group ( http://www.sqloc.com/ ) L.A. SQL Server Users Group ( http://www.sql.la/ ) SQL PASS ( http://www.sqlpass.org/ ) 24 Hours of PASS ( http://www.sqlpass.org/24hours/2010/ ) So stay tuned, there will be more events to come in SoCal!!Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• Oracle Enterprise Manager Cloud Control 12c: Contributing to emerging Cloud standards

  - by Anand Akela

  Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Contributed by Tony Di Cenzo, Director for Standards Strategy and Architecture, and Mark Carlson, Principal Cloud Architect, for Oracle's Systems Management and Storage Products Groups . As one would expect of an industry leader, Oracle's participation in industry standards bodies is extensive. We participate in dozens of organizations that produce open standards which apply to our products, and our commitment to the success of these organizations is manifest in several way - we support them financially through our memberships; our senior engineers are active participants, often serving in leadership positions on boards, technical working groups and committees; and when it makes good business sense we contribute our intellectual property. We believe supporting the development of open standards is fundamental to Oracle meeting customer demands for product choice, seamless interoperability, and lowering the cost of ownership. Nowhere is this truer than in the area of cloud standards, and for the most recent release of our flagship management product, Oracle Enterprise Manager Cloud Control 12c (EM Cloud Control 12c). There is a fundamental rule that standards follow architecture. This was true of distributed computing, it was true of service-oriented architecture (SOA), and it's true of cloud. If you are familiar with Enterprise Manager it is likely to be no surprise that EM Cloud Control 12c is a source of technology that can be considered for adoption within cloud management standards. The reason, quite simply, is that the Oracle integrated stack architecture aligns with the cloud architecture models being adopted by the industry, and EM Cloud Control 12c has been developed to manage this architecture. EM Cloud Control 12c has facilities for managing the various underlying capabilities of the integrated stack in IaaS, PaaS, and SaaS clouds, and enables essential characteristics such as on-demand self-service provisioning, centralized policy-based resource management, integrated chargeback, and capacity planning, and complete visibility of the physical and virtual environment from applications to disk. Our most recent contribution in support of cloud management standards to come out of the EM Cloud Control 12c work was the Oracle Cloud Elemental Resource Model API. Oracle contributed the Elemental Resource Model API to the Distributed Management Task Force (DMTF) in 2011 where it was assigned to DMTF's Cloud Management Working Group (CMWG). The CMWG is considering the Oracle specification and those of several other vendors in their effort to produce a best practices specification for managing IaaS clouds. DMTF's Cloud Infrastructure Management Interface specification, called CIMI for short, is currently out for public review and expected to be released by DMTF later this year. We are proud to be playing an important role in the development of what is expected to become a major cloud standard. You can find more information on DMTF CIMI at http://dmtf.org/standards/cloud. You can find the work-in-progress release of CIMI at http://dmtf.org/content/cimi-work-progress-specifications-now-available-public-comment . The Oracle Cloud API specification is available on the Oracle Technology Network. You can find more information about the Oracle Cloud Elemental Resource Model API on the Oracle Technical Network (OTN), including a webcast featuring the API engineering manager Jack Yu (see TechCast Live: Inside the Oracle Cloud Resource Model API). If you have not seen this video we recommend you take the time to view it. Simply hover your cursor over the webcast title and control+click to follow the embedded link. If you have a question about the Oracle Cloud API or want to learn more about Oracle's participation in cloud management standards efforts drop us a line. We'd love to hear from you. The Enterprise Manager Standards Blogs are written by Tony Di Cenzo, Director for Standards Strategy and Architecture, and Mark Carlson, Principal Cloud Architect, for Oracle's Systems Management and Storage Products Groups. They can be reached at Tony.DiCenzo at Oracle.com and Mark.Carlson at Oracle.com respectively. Stay Connected: Twitter |  Face book |  You Tube |  Linked in |  Newsletter

  Read the article

• using isight camera in macbookpro(8,2) on ubuntu 12.04 virtualbox VM

  - by Kurt Spindler

  I'm having a lot of trouble using the built-in isight camera on my macbookpro8,2 (early 2011) from an ubuntu 12.04 virtual machine, run inside VirtualBox. The following is the log I get when I try to run guvcview ubuntu@ubuntu:~$ guvcview guvcview 1.5.3 ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.rear ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.center_lfe ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.side ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.surround71 ALSA lib setup.c:565:(add_elem) Cannot obtain info for CTL elem (MIXER,'IEC958 Playback Default',0,0,0): No such file or directory ALSA lib setup.c:565:(add_elem) Cannot obtain info for CTL elem (MIXER,'IEC958 Playback Default',0,0,0): No such file or directory ALSA lib setup.c:565:(add_elem) Cannot obtain info for CTL elem (MIXER,'IEC958 Playback Default',0,0,0): No such file or directory ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.hdmi ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.hdmi ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.modem ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.modem ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.phoneline ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.phoneline ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib pcm_dmix.c:957:(snd_pcm_dmix_open) The dmix plugin supports only playback stream Cannot connect to server socket err = No such file or directory Cannot connect to server socket jack server is not running or cannot be started video device: /dev/video0 Init. FaceTime HD Camera (Built-in) (location: usb-0000:00:0b.0-1) { pixelformat = 'YUYV', description = 'YUV 4:2:2 (YUYV)' } { discrete: width = 160, height = 120 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 176, height = 144 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 320, height = 240 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 352, height = 288 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 640, height = 480 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1280, height = 720 } Time interval between frame: 1/10, { pixelformat = 'MJPG', description = 'MJPEG' } { discrete: width = 960, height = 540 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1024, height = 576 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1280, height = 720 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { pixelformat = 'RGB3', description = 'RGB3' } { discrete: width = 160, height = 120 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 176, height = 144 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 320, height = 240 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 352, height = 288 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 640, height = 480 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1280, height = 720 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 960, height = 540 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1024, height = 576 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { pixelformat = 'BGR3', description = 'BGR3' } { discrete: width = 160, height = 120 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 176, height = 144 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 320, height = 240 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 352, height = 288 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 640, height = 480 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1280, height = 720 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 960, height = 540 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1024, height = 576 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { pixelformat = 'YU12', description = 'YU12' } { discrete: width = 160, height = 120 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 176, height = 144 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 320, height = 240 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 352, height = 288 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 640, height = 480 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1280, height = 720 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 960, height = 540 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1024, height = 576 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { pixelformat = 'YV12', description = 'YV12' } { discrete: width = 160, height = 120 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 176, height = 144 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 320, height = 240 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 352, height = 288 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 640, height = 480 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1280, height = 720 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 960, height = 540 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1024, height = 576 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, vid:05ac pid:8509 driver:uvcvideo checking format: 1196444237 VIDIOC_G_COMP:: Invalid argument compression control not supported fps is set to 1/25 drawing controls no codec detected for H264 no codec detected for MP3 - (lavc) Checking video mode 960x540@32bpp : OK Could not grab image (select timeout): Resource temporarily unavailable Could not grab image (select timeout): Resource temporarily unavailable Could not grab image (select timeout): Resource temporarily unavailable Could not grab image (select timeout): Resource temporarily unavailable Could not grab image (select timeout): Resource temporarily unavailable Could not grab image (select timeout): Resource temporarily unavailable Could not grab image (select timeout): Resource temporarily unavailable Could not grab image (select timeout): Resource temporarily unavailable Could not grab image (select timeout): Resource temporarily unavailable write /home/ubuntu/.guvcviewrc OK free controls cleaned allocations - 100% Closing portaudio ...OK Closing GTK... OK ubuntu@ubuntu:~$ Any help would be greatly appreciated. Only clue I have is that I initially was having problems, tried using the old method of fixing isights (involving installing isight-firmware-tools) before realizing that I just hadn't turned on the VM setting to allow the VM to access the webcam. :) Anyway, I wonder if installing that messed something up. However, I think this is a red herring because I've: shut down and turned back on the Mac, restarted the VM, tried a different VM (for which I never installed isight-firmware-tools, and created an entirely new ubuntu vm. All instances have had this problem. Similarly, other viewers, such as cheese, avplay, avconv have had all various kinds of errors.

  Read the article

• Sound issues after trying everything

  - by Lerp

  I cannot get my sound working properly, no matter what I do, there's always some problem. It's very annoying as it's the only thing preventing me from making Ubuntu my main OS. At the moment my sound always plays through both my speakers and my headphones regardless except the sound through the headphones is crackly. It is also a bit quiet even though everything is maxed. I've managed to improve the situation to a point where the sound out of my speakers is perfect but I have none at all from my headphones. I do have two connectors listed in the sound settings but regardless of which one is selected it always plays through the speakers. I think this might have something to do with the fact that my speakers are plugging into the front of my computer, typically the headphone jack, and my headphones are plugging into the back but when I try disconnecting the speakers from the front there is still no sound from the headphones. I fixed the speaker sound by going through the sound settings and making sure they were all set to 100% then rebooting. Things I have tried: Maxing everything and unmuting everything in alsamixer Uninstalling pulseaudio Making gstreamer use only alsa via gstreamer-properties. This worked with the sound test button including independent sound between headphones and speakers but when I reset the computer it no longer worked. So I tried setting it manually in gconf-editor which didn't work either. Reinstalling alsa and pulseaudio Setting the model in /etc/modprobe.d/alsa-base.conf to 6stack and 6stack-dig neither worked. Upgrading to 12.10 Here's some command output to help you diagnose my problem. aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Intel [HDA Intel], device 0: AD198x Analog [AD198x Analog] Subdevices: 0/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 1: AD198x Digital [AD198x Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 2: AD198x Headphone [AD198x Headphone] Subdevices: 1/1 Subdevice #0: subdevice #0 sudo lshw -C sound *-multimedia description: Audio device product: 82801JI (ICH10 Family) HD Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:70 memory:f7ff8000-f7ffbfff cat /proc/asound/card*/codec* | grep "Codec" Codec: Analog Devices AD1989B cat /etc/modprobe.d/alsa-base.conf # autoloader aliases install sound-slot-0 /sbin/modprobe snd-card-0 install sound-slot-1 /sbin/modprobe snd-card-1 install sound-slot-2 /sbin/modprobe snd-card-2 install sound-slot-3 /sbin/modprobe snd-card-3 install sound-slot-4 /sbin/modprobe snd-card-4 install sound-slot-5 /sbin/modprobe snd-card-5 install sound-slot-6 /sbin/modprobe snd-card-6 install sound-slot-7 /sbin/modprobe snd-card-7 # Cause optional modules to be loaded above generic modules install snd /sbin/modprobe --ignore-install snd $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-ioctl32 ; /sbin/modprobe --quiet --use-blacklist snd-seq ; } # # Workaround at bug #499695 (reverted in Ubuntu see LP #319505) install snd-pcm /sbin/modprobe --ignore-install snd-pcm $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-pcm-oss ; : ; } install snd-mixer /sbin/modprobe --ignore-install snd-mixer $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-mixer-oss ; : ; } install snd-seq /sbin/modprobe --ignore-install snd-seq $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq-midi ; /sbin/modprobe --quiet --use-blacklist snd-seq-oss ; : ; } # install snd-rawmidi /sbin/modprobe --ignore-install snd-rawmidi $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq-midi ; : ; } # Cause optional modules to be loaded above sound card driver modules install snd-emu10k1 /sbin/modprobe --ignore-install snd-emu10k1 $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-emu10k1-synth ; } install snd-via82xx /sbin/modprobe --ignore-install snd-via82xx $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq ; } # Load saa7134-alsa instead of saa7134 (which gets dragged in by it anyway) install saa7134 /sbin/modprobe --ignore-install saa7134 $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist saa7134-alsa ; : ; } # Prevent abnormal drivers from grabbing index 0 options bt87x index=-2 options cx88_alsa index=-2 options saa7134-alsa index=-2 options snd-atiixp-modem index=-2 options snd-intel8x0m index=-2 options snd-via82xx-modem index=-2 options snd-usb-audio index=-2 options snd-usb-caiaq index=-2 options snd-usb-ua101 index=-2 options snd-usb-us122l index=-2 options snd-usb-usx2y index=-2 # Ubuntu #62691, enable MPU for snd-cmipci options snd-cmipci mpu_port=0x330 fm_port=0x388 # Keep snd-pcsp from being loaded as first soundcard options snd-pcsp index=-2 # Keep snd-usb-audio from beeing loaded as first soundcard options snd-usb-audio index=-2 options snd-hda-intel model=6stack

  Read the article

• How do I resolve this exercise on C++? [closed]

  - by user40630

  (Card Shuffling and Dealing) Create a program to shuffle and deal a deck of cards. The program should consist of class Card, class DeckOfCards and a driver program. Class Card should provide: a) Data members face and suit of type int. b) A constructor that receives two ints representing the face and suit and uses them to initialize the data members. c) Two static arrays of strings representing the faces and suits. d) A toString function that returns the Card as a string in the form “face of suit.” You can use the + operator to concatenate strings. Class DeckOfCards should contain: a) A vector of Cards named deck to store the Cards. b) An integer currentCard representing the next card to deal. c) A default constructor that initializes the Cards in the deck. The constructor should use vector function push_back to add each Card to the end of the vector after the Card is created and initialized. This should be done for each of the 52 Cards in the deck. d) A shuffle function that shuffles the Cards in the deck. The shuffle algorithm should iterate through the vector of Cards. For each Card, randomly select another Card in the deck and swap the two Cards. e) A dealCard function that returns the next Card object from the deck. f) A moreCards function that returns a bool value indicating whether there are more Cards to deal. The driver program should create a DeckOfCards object, shuffle the cards, then deal the 52 cards. This above is the exercise I'm trying to solve. I'd be very much appreciated if someone could solve it and explain it to me. The main idea of the program is quite simple. What I don't get is how to build the constructor for the class DeckOfCards and how to generate the 52 cards of the deck with different suits and faces. Untill now I've managed to do this: #include <iostream> #include <vector> using namespace std; /* * */ /* a) Data members face and suit of type int. b) A constructor that receives two ints representing the face and suit and uses them to initialize the data members. c) Two static arrays of strings representing the faces and suits. d) A toString function that returns the Card as a string in the form “face of suit.” You can use the + operator to concatenate strings. */ class Card { public: Card(int, int); string toString(); private: int suit, face; static string faceNames[13]; static string suitNames[4]; }; string Card::faceNames[13] = {"Ace","Two","Three","Four","Five","Six","Seven","Eight","Nine","Ten","Queen","Jack","King"}; string Card::suitNames[4] = {"Diamonds","Clubs","Hearts","Spades"}; string Card::toString() { return faceNames[face]+" of "+suitNames[suit]; } Card::Card(int f, int s) :face(f), suit(s) { } /* Class DeckOfCards should contain: a) A vector of Cards named deck to store the Cards. b) An integer currentCard representing the next card to deal. c) A default constructor that initializes the Cards in the deck. The constructor should use vector function push_back to add each Card to the end of the vector after the Card is created and initialized. This should be done for each of the 52 Cards in the deck. d) A shuffle function that shuffles the Cards in the deck. The shuffle algorithm should iterate through the vector of Cards. For each Card, randomly select another Card in the deck and swap the two Cards. e) A dealCard function that returns the next Card object from the deck. f) A moreCards function that returns a bool value indicating whether there are more Cards to deal. */ class DeckOfCards { public: DeckOfCards(); void shuffleCards(); Card dealCard(); bool moreCards(); private: vector<Card> deck(52); int currentCard; }; int main(int argc, char** argv) { return 0; } DeckOfCards::DeckOfCards() { //I'm stuck here I have no idea of what to take out of here. //I still don't fully get the idea of class inside class and that's turning out as a problem. I try to find a way to set the suits and faces members of the class Card but I can't figure out how. for(int i=0; i<deck.size(); i++) { deck[i]//....There is no function to set them. They must be set when initialized. But how?? } } For easier reading: http://pastebin.com/pJeXMH0f

  Read the article

• Linq to List and IEnumerable issues

  - by Otaku

  I am querying an HTML file with Linq. It looks something like this: <html> <body> <div class="Players"> <div class="role">Goalies</div> <div class="name">John Smith</div> <div class="name">Shawn Xie</div> <div class="role">Right Wings</div> <div class="name">Jack Davis</div> <div class="name">Carl Yuns</div> <div class="name">Wayne Gortonia</div> <div class="role">Centers</div> <div class="name">Lutz Gaspy</div> <div class="name">John Jacobs</div> </div </html> </body> What I'm trying to do is create a list of these folks like in a list of a structure called Players: Structure Players Public Name As String Public Position As String End Structure But I've quickly found out I don't really know what I'm doing when it comes to Linq. I've got this far my my queries: Dim goalieList = From d In player.Elements _ Where d.Value = "Goalies" _ Select From g In d.ElementsAfterSelf _ Take While (g.@class <> "role") _ Select New Players With {.Position = "Goalie", _ .Name = g.Value} Dim centersList = From d In player.Elements _ Where d.Value = "Centers" _ Select From g In d.ElementsAfterSelf _ Take While (g.@class <> "role") _ Select New Players With {.Position = "Centers", _ .Name = g.Value} Which gets me down to the the players by position, but then I can't do much with this afterwards the result type is System.Collections.Generic.IEnumerable(Of System.Collections.Generic.IEnumerable(Of Player)) What I want to do is add these two results to a new list, like: Dim playersList As List(Of Players) = Nothing playersList.AddRange(centersList) playersList.AddRange(goalieList) So that I can then query the list and use it. But it kicks the error: Unable to cast object of type 'WhereSelectEnumerableIterator2[System.Xml.Linq.XElement,System.Collections.Generic.IEnumerable1[Players]]' to type 'System.Collections.Generic.IEnumerable`1[Players]' As you can see, I may really have no idea how to work with all these objects/classes. Does anyone have any insight on what I may be doing wrong and how I can resolve it? RESOLVED: The Linq query needs to return a single iEnumerable, like this: Dim goalieList = From l In _ (From d In players.Elements _ Where d.Value = "Goalies" _ Select d.ElementsAfterSelf.TakeWhile(Function(f) f.@class <> "role")) _ Select New Players With {.Position = "Goalie", .Name = l.Value} and then use goalieList.ToList

  Read the article

• Mouse scroll not working in a scroll viewer with a wpf datagrid and additional UI elements

  - by paladugu457

  I am trying to figure out how to get the mouse scroll working on a wpf window with a scrollviewer and a datagrid within it. The WPF and C# code is below <ScrollViewer HorizontalScrollBarVisibility="Disabled" VerticalScrollBarVisibility="Auto"> <Grid> <Grid.RowDefinitions> <RowDefinition/> <RowDefinition/> </Grid.RowDefinitions> <Grid Grid.Row="0"> <Border Name="DataGridBorder" BorderThickness="2" Margin="1" CornerRadius="4" BorderBrush="#FF080757"> <dg:DataGrid AutoGenerateColumns="False" Name="ValuesDataGrid" BorderThickness="0" CanUserResizeColumns="True" FontWeight="Bold" HorizontalScrollBarVisibility="Auto" CanUserReorderColumns="False" IsReadOnly="True" IsTextSearchEnabled="True" AlternationCount="2" SelectionMode="Extended" GridLinesVisibility="All" HeadersVisibility="Column" CanUserAddRows="False" CanUserDeleteRows="False" CanUserResizeRows="False" CanUserSortColumns="False" RowDetailsVisibilityMode="Collapsed" SelectedIndex="0" RowStyle="{StaticResource CognitiDataGridRowStyle}" > <dg:DataGrid.Columns> <dg:DataGridTemplateColumn Header="Title" > <dg:DataGridTemplateColumn.CellTemplate> <DataTemplate> <StackPanel Orientation="Horizontal" > <TextBlock HorizontalAlignment="Left" VerticalAlignment="Center" Text="{Binding Path=Name}" FontWeight="Normal" /> </StackPanel> </DataTemplate> </dg:DataGridTemplateColumn.CellTemplate> </dg:DataGridTemplateColumn> </dg:DataGrid.Columns> </dg:DataGrid> </Border> </Grid> <Button Grid.Row="1" Height="90" >hello world</Button> </Grid> </ScrollViewer> and the C# code is as follows public partial class Window1 : Window { public Window1() { InitializeComponent(); initialize(); } public void initialize() { ObservableCollection<MyObject> testList = new ObservableCollection<MyObject>(); for (int i = 0; i < 20; i++) { MyObject my = new MyObject("jack " + i); testList.Add(my); } ValuesDataGrid.ItemsSource = testList; } } public class MyObject { public string Name { get; set; } public MyObject(string name) { Name = name; } } The problem i am facing is that when using the mouse to scroll, it works fine when it is over the button but as soon as i move the mouse pointer over the grid and try to scroll, nothing happens. I am able to move the scrollbar of the scrollviewer directly though. I am still a wpf novice so any help on how to get the mouse scroll to work over the datagrid would be appreciated. I am guessing there should be a pretty easy solution for this but I havent been able to figure it out

  Read the article

• How to interpolate hue values in HSV colour space?

  - by nick

  Hi, I'm trying to interpolate between two colours in HSV colour space to produce a smooth colour gradient. I'm using a linear interpolation, eg: h = (1 - p) * h1 + p * h2 s = (1 - p) * s1 + p * s2 v = (1 - p) * v1 + p * v2 (where p is the percentage, and h1, h2, s1, s2, v1, v2 are the hue, saturation and value components of the two colours) This produces a good result for s and v but not for h. As the hue component is an angle, the calculation needs to work out the shortest distance between h1 and h2 and then do the interpolation in the right direction (either clockwise or anti-clockwise). What formula or algorithm should I use? EDIT: By following Jack's suggestions I modified my JavaScript gradient function and it works well. For anyone interested, here's what I ended up with: // create gradient from yellow to red to black with 100 steps var gradient = hsbGradient(100, [{h:0.14, s:0.5, b:1}, {h:0, s:1, b:1}, {h:0, s:1, b:0}]); function hsbGradient(steps, colours) { var parts = colours.length - 1; var gradient = new Array(steps); var gradientIndex = 0; var partSteps = Math.floor(steps / parts); var remainder = steps - (partSteps * parts); for (var col = 0; col < parts; col++) { // get colours var c1 = colours[col], c2 = colours[col + 1]; // determine clockwise and counter-clockwise distance between hues var distCCW = (c1.h >= c2.h) ? c1.h - c2.h : 1 + c1.h - c2.h; distCW = (c1.h >= c2.h) ? 1 + c2.h - c1.h : c2.h - c1.h; // ensure we get the right number of steps by adding remainder to final part if (col == parts - 1) partSteps += remainder; // make gradient for this part for (var step = 0; step < partSteps; step ++) { var p = step / partSteps; // interpolate h var h = (distCW <= distCCW) ? c1.h + (distCW * p) : c1.h - (distCCW * p); if (h < 0) h = 1 + h; if (h > 1) h = h - 1; // interpolate s, b var s = (1 - p) * c1.s + p * c2.s; var b = (1 - p) * c1.b + p * c2.b; // add to gradient array gradient[gradientIndex] = {h:h, s:s, b:b}; gradientIndex ++; } } return gradient; }

  Read the article

• creating executable jar file for my java application

  - by Manu

  public class createExcel { public void write() throws IOException, WriteException { WorkbookSettings wbSettings = new WorkbookSettings(); wbSettings.setLocale(new Locale("en", "EN")); WritableWorkbook workbook1 =Workbook.createWorkbook(new File(file), wbSettings); workbook1.createSheet("Niru ", 0); WritableSheet excelSheet = workbook1.getSheet(0); createLabel(excelSheet); createContent(excelSheet,list); workbook1.write(); workbook1.close(); } public void createLabel(WritableSheet sheet)throws WriteException { WritableFont times10pt = new WritableFont(WritableFont.createFont("D:\font\trebuct"),8); // Define the cell format times = new WritableCellFormat(times10pt); // Lets automatically wrap the cells times.setWrap(false); WritableFont times10ptBoldUnderline = new WritableFont( WritableFont.createFont("D:\font\trebuct"), 9, WritableFont.BOLD, false, UnderlineStyle.NO_UNDERLINE); timesBoldUnderline = new WritableCellFormat(times10ptBoldUnderline); sheet.setColumnView(0,15); sheet.setColumnView(1,13); // Write a few headers addCaption(sheet, 0, 0, "Business Date"); addCaption(sheet, 1, 0, "Dealer ID"); } private void createContent(WritableSheet sheet, ArrayList list) throws WriteException,RowsExceededException { // Write a few number for (int i = 1; i < 11; i++) { for(int j=0;j<11;j++){ // First column addNumber(sheet, i, j,1); // Second column addNumber(sheet, 1, i, i * i); } } } private void addCaption(WritableSheet sheet, int column, int row, String s) throws RowsExceededException, WriteException { Label label; label = new Label(column, row, s, timesBoldUnderline); sheet.addCell(label); } private void addNumber(WritableSheet sheet, int row,int column, Integer integer) throws WriteException, RowsExceededException { Number number; number = new Number(column,row, integer, times); sheet.addCell(number); } public static void main(String[] args) { JButton myButton0 = new JButton("Advice_Report"); JButton myButton1 = new JButton("Position_Report"); JPanel bottomPanel = new JPanel(); bottomPanel.add(myButton0); bottomPanel.add(myButton1); myButton0.addActionListener(this); myButton1.addActionListener(this); createExcel obj=new createExcel(); obj.setOutputFile("c;\\temp\\swings\\jack.xls"); try{ obj.write(); }catch(Exception e){} } and so on. it working fine. i have jxl.jar and ojdbc14.jar files(need this jar file for Excelsheet creation and DB connection )and createExcel.class(.class file) file. how to make this code as executable jar file.

  Read the article

• Fread binary file dynamic size string [C]

  - by Blackbinary

  I've been working on this assignment, where I need to read in "records" and write them to a file, and then have the ability to read/find them later. On each run of the program, the user can decide to write a new record, or read an old record (either by Name or #) The file is binary, here is its definition: typedef struct{ char * name; char * address; short addressLength, nameLength; int phoneNumber; }employeeRecord; employeeRecord record; The way the program works, it will store the structure, then the name, then the address. Name and address are dynamically allocated, which is why it is necessary to read the structure first to find the size of the name and address, allocate memory for them, then read them into that memory. For debugging purposes I have two programs at the moment. I have my file writing program, and file reading. My actual problem is this, when I read a file I have written, i read in the structure, print out the phone # to make sure it works (which works fine), and then fread the name (now being able to use record.nameLength which reports the proper value too). Fread however, does not return a usable name, it returns blank. I see two problems, either I haven't written the name to the file correctly, or I haven't read it in correctly. Here is how i write to the file: where fp is the file pointer. record.name is a proper value, so is record.nameLength. Also i am writing the name including the null terminator. (e.g. 'Jack\0') fwrite(&record,sizeof record,1,fp); fwrite(record.name,sizeof(char),record.nameLength,fp); fwrite(record.address,sizeof(char),record.addressLength,fp); And i then close the file. here is how i read the file: fp = fopen("employeeRecord","r"); fread(&record,sizeof record,1,fp); printf("Number: %d\n",record.phoneNumber); char *nameString = malloc(sizeof(char)*record.nameLength); printf("\nName Length: %d",record.nameLength); fread(nameString,sizeof(char),record.nameLength,fp); printf("\nName: %s",nameString); Notice there is some debug stuff in there (name length and number, both of which are correct). So i know the file opened properly, and I can use the name length fine. Why then is my output blank, or a newline, or something like that? (The output is just Name: with nothing after it, and program finishes just fine) Thanks for the help.

  Read the article

• :contains for multiple words

  - by Emin

  I am using the following jQuery var etag='kate' if (etag.length > 0) { $('div').each(function () { $(this).find('ul:not(:contains(' + etag + '))').hide(); $(this).find('ul:contains(' + etag + ')').show(); }); }? towards the following HTML <div id="2"> <ul> <li>john</li> <li>jack</li> </ul> <ul> <li>kate</li> <li>clair</li> </ul> <ul> <li>hugo</li> <li>desmond</li> </ul> <ul> <li>said</li> <li>jacob</li> </ul> </div> <div id="3"> <ul> <li>jacob</li> <li>me</li> </ul> <ul> <li>desmond</li> <li>george</li> </ul> <ul> <li>allen</li> <li>kate</li> </ul> <ul> <li>salkldf</li> <li>3kl44</li> </ul> </div> basically, as long as etag has one word, the code works perfectly and hides those elements who do not contain etag. My problem is, when etag is multiple words (and I don't have control over it. Its coming from a database and could be combination of multiple words seperated with space char) then the code does not work.. is there any way to achieve this?

  Read the article

• onListItemClick with Mulitple Value/Retrieving Value

  - by JuniorFlip

  Hello, I am trying to retrieve the value from a Arraylist/ArrayAdapter that I have populated. I believe my issue is at the Onitemclick event. What I would like to accomplished is that when I click on Yasmin, I can return the value of 8. Please let me know if I am on the right track import java.util.ArrayList; import android.app.Activity; import android.os.Bundle; import android.view.View; import android.widget.AdapterView; import android.widget.ArrayAdapter; import android.widget.ListView; import android.widget.TextView; import android.widget.AdapterView.OnItemClickListener; public class lister extends Activity { /** Called when the activity is first created. */ TextView txHomeTeam; protected ListView mFavlist; protected ArrayList fakeFavs = new ArrayList(); @Override public void onCreate(Bundle icicle) { super.onCreate(icicle); this.setContentView(R.layout.main); this.txHomeTeam = (TextView)this.findViewById(R.id.title); fakeFavs.add(new Favorite("John", "1")); fakeFavs.add(new Favorite("Yasmin", "8")); fakeFavs.add(new Favorite("Jack", "10")); //this.mFavlist = (ListView) this.findViewById(R.id.list_favorites); this.mFavlist = (ListView) this.findViewById(R.id.list_favorites); initListView(); mFavlist.setTextFilterEnabled(true); mFavlist.setOnItemClickListener(new OnItemClickListener() { @Override public void onItemClick(AdapterView arg0, View view, int position, long id) { // user clicked a list item, //and read the value from <Favorite>.value //txHomeTeam.setText=???? } }); } public void refreshFavListItems() { mFavlist.setAdapter(new ArrayAdapter(this, android.R.layout.simple_list_item_1, fakeFavs)); } public void initListView() { /* Loads the items to the ListView. */ refreshFavListItems(); } protected class Favorite { protected String Detail; protected String value; protected Favorite(String Detail, String value) { this.Detail = Detail; this.value = value; } public String toString() { return Detail; } } }

  Read the article

• Why does the following Java Script fail to load XML?

  - by Pavitar

  I have taken an example taught to us in class,wherein a javascript is used to retrieve data from the XML,but it doesn't work.Please help I have also added the XML file below. <html> <head> <title>Customer Info</title> <script language="javascript"> var xmlDoc = 0; var xmlObj = 0; function loadCustomers(){ xmlDoc = new ActiveXObject("Microsoft.XMLDOM"); xmlDoc.async = "false"; xmlDoc.onreadystatechange = displayCustomers; xmlDoc.load("customers.xml"); } function displayCustomers(){ if(xmlDoc.readyState == 4){ xmlObj = xmlDoc.documentElement; var len = xmlObj.childNodes.length; for(i = 0; i < len; i++){ var nodeElement = xmlObj.childNodes[i]; document.write(nodeElement.attributes[0].value); for(j = 0; j < nodeElement.childNodes.length; j++){ document.write(" " + nodeElement.childNodes[j].firstChild.nodeValue); } document.write("<br/>"); } } } </script> </head> <body> <form> <input type="button" value="Load XML" onClick="loadCustomers()"> </form> </body> </html> XML(customers.xml) <?xml version="1.0" encoding="UTF-8"?> <customers> <customer custid="CU101"> <pwd>PW101</pwd> <email>[email protected]</email> </customer> <customer custid="CU102"> <pwd>PW102</pwd> <email>[email protected]</email> </customer> <customer custid="CU103"> <pwd>PW103</pwd> <email>[email protected]</email> </customer> <customer custid="CU104"> <pwd>PW104</pwd> <email>[email protected]</email> </customer> </customers>

  Read the article

• Learn C# now or finish up with Java and then learn C#?

  - by Sahat

  Ok here is my situation. I've studied Java in my college for 2 semesters. But you know they teach you jack in there, just the basics. We skipped half of our textbook and even then our professors don't teach from section to section of each chapter. I don't blame them. It's hard as it is for new students to understand even the basic concepts of programming. Now this is a community college we are talking about and not Stanford, MIT or Berkeley. So like I said I've done 2 semester of Java. I really like our textbook because it has some challenging projects to do at the end of each chapter. This textbook is pretty clear and i have no problem understanding it (although 2-D and 3-D Arrays have given me some trouble). I have tried reading a few C# books such as Pro C# 2008 and .NET 3.5 and C# 4.0 in a Nutshell. I found these books to be dry and overloaded with information that put me to sleep (No offense to the authors of those 2 wonderful, according to amazon ratings, books). Would you suggest I finish my Java textbook, brush up my knowledge of Arrays, Polymorphism, and etc that are universal to most programming languages. And then switch to C#, plus the syntax is very similar so it should be easy to switch. Or should I just start learning C# right now from the very beginning? If it's the latter then could you recommend some free online resources that will keep me engaged and at the same time teach me everything I need to know about C#. Someone has recommended me to learn .NET first, but I found it to be not the brightest idea. .NET is just a big monster full of libraries. How am I going to apply it if I don't even know the C# or VB!? Anyway back to my question: Master Java and switch to C# or just go with C#? DISCLAIMER: I don't want to start .NET vs J2EE or C# vs Java flame war. I am going with C#. I've decided that I want to work in a Microsoft shop in the future. .NET is what I want to learn. Thanks! Will be waiting for the answers.

  Read the article

• My form submit button is not showing correctly

  - by JackR

  I have created an form that submits the contents to email. I have used the exact same coding in many other websites, but for my new website http://www.peterevansfuneraldirectors.co.uk/contact-us.html the submit button is just a grey square with text, rather than the usual button. Also the hand doesn't come up on hover. My form code is... <form action="php/FormToEmail.php" method="post" name="ContactForm" id="ContactForm" onsubmit="MM_validateForm('name','','R','email','','RisEmail','message subject','','R','message','','R');return document.MM_returnValue" > <div class="form-text"> <b>Name<span class="purple">*</span></b><br /> <input name="name" type="text" id="name" size="35" style="height:23px; background-color:#FFF; color:#000; border: 1px solid #CCC;" /> </div><br /> <div class="form-text"> <b>Email<span class="purple">*</span></b><br /> <input name="email" type="text" id="email" size="35" style="height:23px; background-color:#FFF; color:#000; border: 1px solid #CCC;" /> </div><br /> <div class="form-text"> <b>Message Subject<span class="purple">*</span></b><br /> <input name="message subject" type="text" id="message subject" size="35" style="height:23px; background-color:#FFF; color:#000; border: 1px solid #CCC;" /> </div><br /> <div class="form-text"> <b>Message<span class="purple">*</span></b><br /> <textarea name="message" type="text" id="message" rows="8" cols="55" style="background-color:#FFF; color:#000; border: 1px solid #CCC;" ></textarea> </div><br /> <div class="submit-button"> <input type="submit" name="submit" value="Submit" /> </div> </form> Thanks in advance! Jack.

  Read the article

• extracting multiple tags from xml using PHP

  - by user1479431

  Here is my address.xml <?xml version="1.0" ?> <!--Sample XML document --> <AddressBook> <Addressentry> <firstName>jack</firstName> <lastName>S</lastName> <Address>2899,Ray Road</Address> <Email>[email protected]</Email> </Addressentry> <Addressentry> <firstName>Sid</firstName> <lastName>K</lastName> <Address>238,Baseline Road,TX</Address> <Email>[email protected]</Email> <Email>[email protected]</Email> </Addressentry> <Addressentry> <firstName>Satya</firstName> <lastName>Yar</lastName> <Address>6,Rural Road,Tempe,AZ</Address> <Email>[email protected]</Email> <Email>[email protected]</Email> <Email>[email protected]</Email> </Addressentry> </AddressBook> I am trying to load all the entries using PHP code as below. Each addressentry can have one or more tags. Right now from the code below I am able to extract only one tag. My question is how do I extract all tags associated with particular Addressentry. that is I want to print all emails on the same line. <?php $theData = simplexml_load_File("address.xml"); foreach($theData->Addressentry as $theAddress) { $theFirstName = $theAddress->firstName; $theLastName = $theAddress->lastName; $theAdd = $theAddress->Address; echo "<p>".$theFirstName." ".$theLastName."<br/> ".$theAdd."<br/> ".$theAddress->Email."<br/> </p>"; unset($theFirstName); unset($theLastName); unset($theAdd); unset($theEmail); } ?> Any help would be appreciated

  Read the article

• Bypass BIOS password set by faulty Toshiba firmware on Satellite A55 laptop?

  - by Brian

  How can the CMOS be cleared on the Toshiba Satellite A55-S1065? I have this 7 year old laptop that has been crippled by a glitch in its BIOS: 'A "Password =" prompt may be displayed when the computer is turned on, even though no power-on password has been set. If this happens, there is no password that will satisfy the password request. The computer will be unusable until this problem is resolved. [..] The occurrence of this problem on any particular computer is unpredictable -- it may never happen, but it could happen any time that the computer is turned on. [..] Toshiba will cover the cost of this repair under warranty until Dec 31, 2010.' -Toshiba As they stated, this machine is "unusable." The escape key does not bypass the prompt (nor does any other key), thus no operating system can be booted and no firmware updates can be installed. After doing some research, I found solutions that have been suggested for various Toshiba Satellite models afflicted by this glitch: "Make arrangements with a Toshiba Authorized Service Provider to have this problem resolved." -Toshiba (same link). Even prior to the expiration of Toshiba's support ("repair under warranty until Dec 31, 2010"), there have been reports that this solution is prohibitively expensive, labor charges accruing even when the laptop is still under warranty, and other reports that are generally discouraging: "They were unable to fix it and the guy who worked on it said he couldn’t find the jumpers on the motherboard to clear the BIOS. I paid $39 for my troubles and still have the password problem." - Steve. Since the costs of the repairs can now exceed the value of the hardware, it would seem this is a DIY solution, or a non-solution (i.e. the hardware is trash). Build a Toshiba parallel loopback by stripping and soldering the wires on a DB25 plug to connect connect these pins: 1-5-10, 2-11, 3-17, 4-12, 6-16, 7-13, 8-14, 9-15, 18-25. -CGSecurity. According to a list of supported models on pwcrack, this will likely not work for my Satellite A55-1065 (as well as many other models of similar age). -pwcrack Disconnect the laptop battery for an extended period of time. Doesn't work, laptop sat in a closet for several years without the battery connected and I forgot about the whole thing for awhile. The poor thing. Clear CMOS by setting the proper jumper setting or by removing the CMOS (RTC) battery, or by short circuiting a (hidden?) jumper that looks like a pair of solder marks -various sources for various Satellite models: Satellite A105: "you will see C88 clearly labeled right next the jack that the wireless card plugs into. There are two little solder squares (approx 1/16") at this location" -kerneltrap Satellite 1800: "Underneath the RAM there is black sticker, peel off the black sticker and you will reveal two little solder marks which are actually 'jumpers'. Very carefully hold a flat-head screwdriver touching both points and power on the unit briefly, effectively 'shorting' this circuit." -shadowfax2020 Satellite L300: "Short the B500 solder pads on the system board." -Lester Escobar Satellite A215: "Short the B500 solder pads on the system board." -fixya Clearing the CMOS could resolve the issue, but I cannot locate a jumper or a battery on this board. Nothing that looks remotely like a battery can be removed (everything is soldered). I have looked closely at the area around the memory and do not see any obvious solder pads that could be a secret jumper. Here are pictures (click for full resolution) : Where is the jumper (or solder pads) to short circuit and wipe the CMOS on this board? Possibly related questions: Remove Toshiba laptop BIOS password? Password Problem Toshiba Satellite..

  Read the article

< Previous Page | 44 45 46 47 48 49  | Next Page >