Search Results

Search found 29426 results on 1178 pages for 'user99572 is fine'.

Page 480/1178 | < Previous Page | 476 477 478 479 480 481 482 483 484 485 486 487  | Next Page >

• Network connectivity issue

  - by kubiej21

  I am a novice cisco user and I am trying to investigate as to why one of our connections went down. We have a fiber network ring that is operating just fine. Connected to this ring via ethernet, is a lone 3560. This connection has worked flawlessly for the past year and a half. This morning, I noticed that I could not connect to that remote switch. I checked the configurations on both switches, and nothing has changed (as I expected). In the field, the port lights were flashing, indicating that some sort of communication is occurring. There is only 1 ethernet cable that has been run between these two locations, so testing an alternate path is not possible. What else can I do to fix this connection?

  Read the article

• HP Pavilion dv6 overheating, how do I set fan speed to 100% all the time?

  - by henpenben

  So I have a HP Pavilion dv6, and it works fine. But when I play, say, Minecraft, the temperature jumps to around 60c-70c. I wouldn't be bothered by this, but I bought this computer and played Minecraft on my lap. The laptop overheated and the video card melted. (I'm not kidding) So I was wondering how I could set the fan speed on my laptop to 100% all the time so it never overheats. HP has this "HP Coolsense" thing that when I pick up the laptop and wiggle it around a little bit and pretend it's unstable, the fan cranks up to 100%. I want 100% all the time without me having to pick up the laptop every 10 minutes. Thanks, henpenben

  Read the article

• Two VPN connections from the same IP address

  - by Tayles

  I have set up a server running Windows Server 2008 which two remote users can dial into using a VPN connection. It works fine unless they are both in the same location, in which case only one of them can connect. I understand this is because the PPTP protocol cannot cope with two VPN connections from the same IP address. Is this correct? If so, what can I do about it? Please note that the remote location in question is a serviced office, so we're not in a position to change or play around with their router. Thanks!

  Read the article

• What is the mount point for Windows share on Ubuntu 9.10?

  - by AMS949

  I am new to Ubuntu so please be gentle! I am taking the plunge from Windows!! I connected to a Windows share (using Connect to Server... menu) and I can access it on Gnome just fine. However, I don't know how I can access it in console, or in any other program that requires the path, when it's already connected on Gnome. What's the mount point for that? I tried the mount command but it does not show up.

  Read the article

• One subdomain is not working

  - by BFTrick

  Hello there, My main domain works just fine - www.example.com and a subdomain set up by another developer works as well - sub1.example.com. But when I try to set another subdomain up I go through the process everything seems to work. The software creates the default files where the subdomain files should go. But when I try to browse there it doesn't work. My host uses Plesk to do all of the hosting stuff. What do you think the problem is? I doubt it is some sort of cache issue because I had problems on my phone which I tried after problems on the pc. Maybe for some reason Plesk needs time to set this up? I have used Cpanel before and that works instantly.

  Read the article

• iPhone and Mac Twitter App Not Parsing HTML in Feeds

  - by otakrosak

  I've come across this problem where my tweets on the iPhone and Mac Twitter app are not parsing the HTML properly. In any browser, the HTML is parsed fine. It only happens to the apostrophe character (') and on the iPhone and Mac Twitter app. Also, I'm using the dlvr.it service to push my Drupal blog posts to my Twitter feed. My initial guess was that it was the RSS generated by Drupal, but if that were the case, then the feed displayed on the browser would be affected too. Any ideas anyone? Any help would be very much appreciated. P.S: I apologize beforehand if this question already exists. I did search for it but based on what I queried, nothing came up.

  Read the article

• Cannot assign multi-line values to CustomAttributes with Set-Mailbox

  - by Biglig

  A colleague is implementing an application that generates signatures and publishes them to Outlook. It would be useful to him if I could store a multi-line string for each user in Active-Directory. Using one of the Custom-Attributes seems obvious, but if I try set-mailbox biglig -CustomAtribute1 "First Line``r``n Second Line" then CustomAttribute1 gets set to "FirstLineSecondLine" and looses the breaks. However, the same syntax works fine when I set e.g. StreetAddress or Notes. Of course, those are changed with set-user rather than set-mailbox. According to Technet's reference for set-user and set-mailbox, The CustomAttributes, StreetAddress, and Notes all take a system.string as their value. Is it just the case that some attributes accept multi-line strings and some don't? If so, can anyone suggest a workaround?

  Read the article

• Application got shut down in WinXP if I close the 2nd window of that application.

  - by kinopyo

  I'm using WinXP and here is my question: I run an application, such as Chrome, there would be one app in the task bar, and it's fine. Suppose a new window of Chrome opened(so there would be 2 window and 2 in the task bar), and when I close that,the 2nd one, the whole application just shutdown. And so does chrome, firefox, evernote, Becky!(the email client), even TortoiseSVN. So I think there should be a generic problem cause these applications shutdown, such as the platform - WinXP. Please give me some advice or hint, anything comes to your mind would be helpful!

  Read the article

• How to forbid postfix to send to external domains [closed]

  - by elhoim

  I have a local postfix server, and i want it to only relay emails to the only local domain (localdomain.be): myhostname = localdomain.be mydomain = localdomain.be alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = $myhostname mydestination = $myhostname relay_domains = $mydomain default_transport = smtp relayhost = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 10.0.0.0/24 mailbox_size_limit = 64000000 message_size_limit = 1000000 recipient_delimiter = + inet_interfaces = all inet_protocols = all smtp_host_lookup = native This configuration works fine to allow relay mail locally and on external destination domains, but i would like it to be an impossibility to send to other domains (ie: gmail.com). relay_domains is supposed to ensure that but it does not seem to really filter since i can still send to my gmail address.

  Read the article

• Which LAN driver should I use for Asus F5Z ?

  - by Radek

  A friend of mine asked me to re-install his Asus F5Z notebook with Windows XP. I installed successfully all drivers from Asus driver download site. Everything is working fine but the Ethernet driver. The installation of Lan Driver for Windows XP finishes with strange message "Please shutdown & plug Realtech PCI-e card to complete the installation. Not sure if it matters but OnChip SATA is in 'Native IDE' mode . The original one with Vista was 'IDE - AHCI mode'. Any idea how I can make the LAN adapter to work under Windows XP?

  Read the article

• What can cause a black or blank screen when pressing logout or switch user in windows 7

  - by Medran

  The situation I have here is related to a brand new dell machine with a GTX260 video card. Put simply after one user logs in when that user either 'switch users' or 'logs out' windows goes to a black/blank screen. The TV screen that is used with this computer previously functioned fine with fast user switching on an XP machine. The new computer is windows 7. The TV is not outputting any error messages like 'no signal' or anything else that would be displayed if the computer was off. You can fix the problem by cycling the input on television, after cycling the input the welcome screen appears as normal. What I want to know is what on earth is windows doing that would cause the video card to stop sending the same signal to the monitor when the user logs off or switches users. I mean as far as I can tell the resolution is identical between windows and the welcome screen. Or perhaps if somebody has experienced this before a fix would be great too.

  Read the article

• Mac Snow Leopard Server DNS

  - by panomedia

  I have a Tomcat-driven application on my Windows server that I am planning to move to a MacMiniServer. Before I do this, I want to fully test the transition for licensing purposes. I have a Fire drive setup with Snow Leopard Server and the base app runs just fine BUT I need to be able to resolve the URL to my domain and not localhost. So, I figured I would setup panomedia.net in the DNS Server and also create an A record to my internal network IP so www.panomedia.net would dish out the same thing as localhost. The problem is: The Tomcat web app starts up going through panomedia.local and not through www.panomedia.net and My main network preference panel is still looking at my Comcast DNS search providers even though I put my local IP address as the only DNS Server and Search provider. I need to test this via an actual domain name before I commit to a 400GB data move. Can anyone help?

  Read the article

• Networking issues with WNR3500L

  - by ageis23

  When I try connecting to my wireless network it attempts to connect then gives up. There's something strange going on with the mac's. The eternet switch and all the vlan interfaces have a mac 00:FF:FF:FF:FF:FF. config 'switch' 'eth0' option 'vlan0' '2 3 4 8*' option 'vlan1' '0 8' option 'vlan2' '1 8' config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'lan' option 'type' 'bridge' option 'ifname' 'eth0.1' option 'proto' 'static' option 'netmask' '255.255.255.0' option 'ipaddr' '192.168.2.1' option 'ip6addr' '' option 'gateway' '192.168.1.253' option 'ip6gw' '' option 'dns' '' config 'interface' 'wan' option 'ifname' 'eth0' option 'proto' 'dhcp' option 'ipaddr' '192.168.1.8' option 'ip6addr' '' option 'netmask' '255.255.255.0' option 'gateway' '192.168.1.253' option 'ip6gw' '' option 'dns' '192.168.1.253' config 'interface' 'dmz' option 'ifname' 'eth0.2' option 'proto' 'static' option 'ipaddr' '192.168.0.1' option 'netmask' '255.255.255.0' Any help on this will be greatly appreciated! When I try setting the mac using macaddr it does nothing. It works perfectly fine when I turn the authentication off.

  Read the article

• CNAME lookup failed temporarily. (#4.4.3)

  - by klickverbot

  A friend of mine just told me that he can't send mails to accounts on one of my servers via the SMTP server provided by his ISP. The error message in the bounce he gets reads: Hi. This is the qmail-send program at aon.at. I'm afraid I wasn't able to deliver your message to the following addresses. This is a permanent error; I've given up. Sorry it didn't work out. <[email protected]>: CNAME lookup failed temporarily. (#4.4.3) I'm not going to try again; this message has been in the queue too long. Any ideas what could be the reason for this? I have double-checked the DNS records for my domain, but they seem perfectly fine, and from any other mail servers I tested, delivery works flawlessly…

  Read the article

• Second vm not connecting to internet KVM

  - by potsed

  I cannot connect a second VM to the internet. I have two VM's set up and running, the first vm can connect to the Internet fine, the second does not even get a ping through. They are both set up in the same way with the same base packages but different secondary packages. Different sized disks etc. I am a noob with VM and perhaps I am missing something very simple. Like maybe that they have the same mac address or something. They are both using a bridged connection. Any help would be appreciated, and if you need logs please let me know which ones.

  Read the article

• How to restrict access to the files outside document root in apache?

  - by Bakhtiyor

  I have virtual hosts in /var/www/site1 and /var/www/site2 folders. I want to restrict access to the files outside document root in apache virtual host, i.e. site1 could not access files of site2. Right now this scripts in /var/www/site1 works fine, which is not good: $filename = "/var/www/site2/somefile"; $handle = fopen($filename, "r"); $contents = fread($handle, filesize($filename)); echo $contents; How to solve this problem please? Thank you very much!

  Read the article

• Only 5 simultaneously users with PPTP VPN?

  - by Plastkort

  we have a windows 2008 R2 standard server which job is to accept incoming VPN connections via PPTP. it seems to work fine, but the moment the 6th user try to connect, we get the following error: ERROR_VPN_DISCONNECT 807 The network connection between your computer and the VPN server was interrupted. This can be caused by a problem in the VPN transmission and is commonly the result of internet latency or simply that your VPN server has reached capacity. where do we find out how to increase the amount of simultaneously users?, I read somewhere that we can have over 100 connected clients at the same time, when I created this server, I did the following : Network & sharing - Network adapters - File - new incoming connections now I tried to choose and create users here, but we have a domain controller which seems to override this, so the domain users works after this I was able to connect atleast 5 clients... how and where do I increase the "capacity"?

  Read the article

• Allow Internet Access with Default Gateway on Windows 7 VPN Server

  - by Hakoda

  I have a Windows 7 box at home (which I'll refer to as Home-VPN) that runs a simple PPTP VPN server. I have a range of 2 IP address (192.168.1.10-192.168.1.11) to give out, although the server is only able to give out one concurrent connection. Ports 1723 & 47 are correctly forwarded to the server. IPv6 is disabled on both Home-VPN and the client. I setup Home-VPN just like this Youtube video: http://www.youtube.com/watch?v=1s5JxMG06L4 I can connect to it just fine but I can't access the Internet when connected to Home-VPN, all outside web servers (eg. google.com, mozilla.org, apple.com) are unreachable. I know I can uncheck "Use Default Gateway on Remote Servers" on the client side under IPv4 settings but that will route all my traffic through my current connection, rather than through the VPN, defeating the purpose of said VPN. Any ideas on how I can fix this?

  Read the article

• Performance Drop Lingers after Load [closed]

  - by Charles

  Possible Duplicate: How do you do Load Testing and Capacity Planning for Databases I'm noticing a drop in performance after subsequent load tests. Although our cpu and ram numbers look fine, performance seems to degrade over time as sustained load is applied to the system. If we allow more time between the load tests, the performance gets back to about 1,000 ms, but if you apply load every 3 minutes or so, it starts to degrade to a point where it takes 12,000 ms. None of the application servers are showing lingering apache processes and the number of database connections cools down to about 3 (from a sustained 20). Is there anything else I should be looking out for here?

  Read the article

• IIS 7 with PHP in Domain with Windows Authentication

  - by Michal Saiyan Hajdony

  I have Windows Server 2008 R2 x64b installed with IIS 7, PHP 5.5. This server is added to domain exampledomain , so I have win authentication enabled and all others disabled. I left the two default providers NTLM and negotiate, I granted IIS_IUSRS read access to wwwroot. So far it has worked for me only as I am added to the Administrators group which has read/write access to wwwroot folder. Yet, when someone else is trying to connect, he gets a credentials window and when he puts the domain name and password he cannot get access to the page. The issue is solved when I add read permission to "Domain users" - then all works fine. BUT. My issue is that if one opens windows explorer and types \\servername\wwwroot one can see the files and read them. I have never configured IIS before so I know I miss some really important thing. How can I solve the file visibility problem?

  Read the article

• Is there a way to use something like RewriteRule ... [PT] for an external URL?

  - by nbolton

  I have a non-apache web server running on port 8000, but this cannot be accessed from behind corporate firewalls. So, I would like to use my apache 2 server as a proxy to this other web server. I've tried using: RewriteEngine On RewriteRule /.* http://buildbot.synergy-foss.org:8000/builders/ [PT] ... but this does not work; I get: Bad Request Your browser sent a request that this server could not understand. However, it worked fine with [R]. Update: Also, when using ProxyPass, I get this error: Forbidden You don't have permission to access / on this server.

  Read the article

• xen virtual machines get to many porcentages of cpus

  - by ki0

  Hi everyone, This is my question. I have one Xen server with 8 CPU's and 6 virtual machine running, each virtual hard disk are running in diferent physical hardisk. Everything worked fine but sometimes one virtual machine get almost whole CPU, if the Domain-0 is 90% that is normal, the virtual machine is 500% usage of CPU. I have improved that it is not depends who are working with the VM even when nobody are working with the server this still happens. I dont know what happen. Anyone have any idea?¿ or anyone have happened the same?¿

  Read the article

• Chrome to download Gmail attachments to a different place

  - by Joe

  I'm using Chrome and Gmail. When I download stuff from the web, Chrome automatically puts it in Downloads, which is fine. However, I'm aware that everything I download from Gmail is in the cloud anyway and so I don't really need it taking up space on my hard drive as well. Is there a way to have Gmail attachements automatically download to a different folder, say, Downloads\Gmail? That way I could regularly purge the ones that won't be useful for a while. (Yes, I'm aware that Word documents and the like often get changed after they arrive, I'm more focused on images, pdfs, and zip files.)

  Read the article

• Relating ping to perceived browser GUI response

  - by cvsdave

  We periodically get complaints of poor GUI (browser page) response that we need to explore. I am looking for a quick and cheap first check to see if the issue is network latency, or server performance. Has anyone encountered any discussion of ping time and perceived GUI response? I understand that GUI response is complicated, but it would be nice if we could find or develop a rule of thumb along the lines of "Hmmmm, ping is over 200, it might be network problems". Ideally, this lives in a script on the user's machine so that we can see the latency that they are seeing... (BASH, Linux). A reference to a good discussion page would be a fine answer, as would any recommendation of other source material.

  Read the article

• Can't set up printer

  - by Jason Swett

  I'm trying to set up an HP OFficejet Pro 8500 A909a on my Windows XP machine over the network. I know the IP address of the printer but it's unclear to me how to set it up based on that. I have no idea how to troubleshoot this problem. I've tried installing the drivers but when I do that it tells me the printer is on a different gateway from my workstation, which is not true. Also, other people in the office are able to connect to this printer just fine, although the driver apparently didn't work for them, either.

  Read the article

< Previous Page | 476 477 478 479 480 481 482 483 484 485 486 487  | Next Page >