Search Results

Search found 13401 results on 537 pages for 'double checked'.

Page 488/537 | < Previous Page | 484 485 486 487 488 489 490 491 492 493 494 495  | Next Page >

• RAID controller dropping the wrong drive

  - by bramp

  I've been having an issue with 3ware 9500S-8 RAID 10, and I have contracted their tech support, but I wanted to hear the serverfault community's recommendations. Firstly, all my data is backuped and secure, so I don't mind blowing my RAID away if I have to. But let me describe the problem I've been seeing. A month ago, disk 6 dropped out of the RAID. It is mirrored with disk 7, so I wasn't that bothered. I went to the data centre and replaced it. When I got back to the office, I noticed that disk 6 will still not in the RAID, and in fact the controller was show the name of the old drive still. A week later I went back and replace the drive again, thinking I might have swapped in a bad drive. Still the same problem. I decided to reboot the machine, to see if that would "force" the controller into seeing the new drive. It did, and a rebuild started to happen (from disk 7). Eventually both drives were showing as good. A week later, the MySQL database has flagged the database is corrupt, and is unable to repair it. I don't know what has gone wrong, but I suspected this 6-7 pair. At this point I noticed that the RAID had constantly been verifying itself, over and over. Regardless of this I began to rebuild the database, which took about 19 hours. It's a big database. Near the end of the repair, the RAID controller told me it had dropped disk 7, and that some data was most likely corrupted. I contacted LSI tech support, and they very promptly started to help me. I mentioned that drive 7 had been dropped. They suspect that drive 7 was always at fault, and drive 6 had always been good. I want to know how often a RAID controller would drop the wrong drive (in this case dropping drive 6 a month ago, instead of 7). I foolishly didn't run smartctl on the drives before I started swapping them out. I just assumed the RAID controller knew what it was talking about. I think my plan of action is to replace drive 7, rebuild the array from scratch, double check smartctl on ALL the disks, and then start restoring my data again. I would appreciate anyone's input on what the correct procedure for swapping drives is, and how often failures like this happen. If anyone would like more information then I'd be happy to provide it. thanks in advance. Oh some more information. I'm running CentOS 5.3, with two RAID arrays, a simple RAID 1 for the OS, and RAID 10 for the database. Both arrays are on different controllers. The RAID 10 is made of 10 identical ST3640323AS drives, until I swapped in a SAMSUNG HD103SJ last month.

  Read the article

• Add user in CentOS 5

  - by Ron

  I created a new user in my CentOS web server with useradd. Added a password with passwd. But I can't log in with the user via SSH. I keep getting 'access denied'. I checked to make sure that the password was assigned and that the account is active. /var/log/secure shows the following error: Aug 13 03:41:40 server1 su: pam_unix(su:auth): authentication failure; logname= uid=500 euid=0 tty=pts/0 ruser=rwade rhost= user=root Please help, Thanks Thanks for the responses so far: I should add that it is a VPS on a remote computer, fresh out of the box. I can log in as the root user quite fine. I can also su to the new user, but I cannot log in as the new user. Here is my sshd_config file: # $OpenBSD: sshd_config,v 1.73 2005/12/06 22:38:28 reyk Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/usr/local/bin:/bin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. #Port 22 #Protocol 2,1 Protocol 2 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh/ssh_host_rsa_key #HostKey /etc/ssh/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 768 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH SyslogFacility AUTHPRIV #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes #StrictModes yes #MaxAuthTries 6 #RSAAuthentication yes #PubkeyAuthentication yes #AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no PasswordAuthentication yes # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes ChallengeResponseAuthentication no # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no GSSAPIAuthentication yes #GSSAPICleanupCredentials yes GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication mechanism. # Depending on your PAM configuration, this may bypass the setting of # PasswordAuthentication, PermitEmptyPasswords, and # "PermitRootLogin without-password". If you just want the PAM account and # session checks to run without PAM authentication, then enable this but set # ChallengeResponseAuthentication=no #UsePAM no UsePAM yes # Accept locale-related environment variables AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL #AllowTcpForwarding yes #GatewayPorts no #X11Forwarding no X11Forwarding yes #X11DisplayOffset 10 #X11UseLocalhost yes #PrintMotd yes #PrintLastLog yes #TCPKeepAlive yes #UseLogin no #UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #ShowPatchLevel no #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner /some/path # override default of no subsystems Subsystem sftp /usr/libexec/openssh/sftp-server

  Read the article

• Apache URL rewriting in reverse proxy

  - by Jeremy Gooch

  I'm deploying Apache in front of a Karaf-hosted application (Apache and Karaf are on separate servers). I want Apache to operate as a reverse proxy and also to hide part of the URL. The URL to get the log-in page of the application directly from the app server is http://app-server:8181/jellyfish. Pages are served by the Jetty instance running within Karaf. Of course, this behaviour would usually be blocked by the firewall for everything except the reverse proxy server. With the firewall off, if you hit this URL then Jetty loads the log-in page. The browser's address bar correctly changes to http://app-server:8181/jellyfish/login?0 and everything works. What I want is for http://web-server (i.e. from the root) to map to Jetty on the app server with the name of the app (jellyfish) suppressed. e.g. The browser would change to show http://web-server/login?0 in the address bar and all subsequent URLs and content would be served with the web-server's domain and without the jellyfish clutter. I can get Apache to operate as a simple reverse proxy, using the following config (snippet):- ProxyPass /jellyfish http://app-server:8181/jellyfish ProxyPassReverse / http://app-server:8181/ ...but this requires the browser's URL to contain jellyfish and going to the root URL (http://web-server) gives a 404 Not Found. I've spent a lot of time trying to use mod_rewrite with and without its [P] flag to get around this, but without success. I then tried the ProxyPassMatch directive, but I can't seem to get that quite correct either. Here's the current config, as is loaded into /etc/apache2/sites-available/ on the web server. Note that there is a locally-hosted images directory. I've also kept the mod_rewrite proxy exploit protection and am suppressing a couple of mod_security rules that were giving false positives. <VirtualHost *:80> ServerAdmin admin@drummer-server ServerName drummer-server ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined Alias /images/ "/var/www/images/" RewriteEngine On RewriteCond %{REQUEST_URI} !^$ RewriteCond %{REQUEST_URI} !^/ RewriteRule .* - [R=400,L] ProxyPass /images ! ProxyPassMatch ^/(.*) http://granny-server:8181/jellyfish/$1 ProxyPassReverse / http://granny-server:8181/jellyfish ProxyPreserveHost On SecRuleRemoveById 981059 981060 <Directory "/var/www/images"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> </VirtualHost> If I go to http://web-server, I get redirected to http://web-server/jellyfish/home but this gives a 404, with a complaint about trying to access /jellyfish/jellyfish/home - NB the browser's address bar does not contain the double /jellyfish. HTTP ERROR 404 Problem accessing /jellyfish/jellyfish/home. Reason: Not Found And, if I go to http://web-server/login, I get redirected to http://web-server/jellyfish/login?0 but this gives a 404, with a complaint about trying to access /jellyfish/jellyfish/login. HTTP ERROR 404 Problem accessing /jellyfish/jellyfish/login. Reason: Not Found So, I'm guessing I'm somehow passing through the rules twice. I am also slightly bemused as to where the home bit of the URL comes from in the first example. Can someone point me in the right direction, please? Thanks, J.

  Read the article

• Win-XP Browsers Hang on page load - (waiting for...)

  - by CHarmon

  Hello, I’m having problems with my browsers hanging on loading pages on my desktop machine. I’m using Windows XP Pro with SP3 and fully updated except for IE 8. All three of my browsers, IE 7, Chrome and Firefox are having the same problems. Pages are not being loaded and are hanging on “waiting for …”. The browsers are waiting for the page being loaded or ad servers. Sometimes a page will load but the loading graphic continues to be displayed as if the page were still loading when the page appears to be fully loaded. The problem is bad enough that I can’t really use any of my browsers. I can eventually get most pages to load by stopping and restarting the page load. I have DSL modem with a wireless router and I have been able to eliminate the modem and router from being the source of my problem. My laptop doesn’t have any problems even when hardwired to the router and with the wireless connection disabled. I deleted the NIC and let XP re-install. Also tried a different network cable. Tried the same router port used in the laptop test. One clue that may be important is that I can’t connect to my router using the desktop machine…the page hangs while trying to connect. I can ping the router and I can quickly connect to the router using the laptop. I also can’t use the Windows update process – the page never fully loads. The problem affects other user accounts and even happens in safe mode. I am convinced the problem is with part of the O/S…some layer able to affect all of the browsers. The purpose of this post is to see if anyone has some ideas before I do a XP repair. I have done quite a bit of trouble-shooting: Ran a full anti-virus scan with AVG – no problems. Ran full scans with Spybot, MalwareBytes and Sophos anti-rootkit – no problems. Ran Chkdsk with both options checked. Ran Disk Clean up Defragged RE-installed IE7 Cleared all the browser caches Ran Ccleaner (registry tool) Ran HijackThis – nothing unusual (problem happens in safe mode too) Ran Process Explorer – no unusual processes Used System Restore and fell back several days – no change in the problem Booted to last known good configuration – no change in the problem Ran MicrosoftFixit50199.msi – no change in the problem Any ideas or suggestions would be appreciated…I’m not looking forward to doing a repair on XP. Thanks in advance for any help.

  Read the article

• Bluetooth not detecting any devices in Windows 7

  - by underDog

  My Lenovo ThinkPad E320 Laptop running Windows 7 64bit has recently been refusing to detect any Bluetooth devices. I have tried to connect, using 'Add devices' under 'devices and printers' to two different Bluetooth mice and my HTC Wildfire android (2.2.1) phone and none of them are detected in the 'Add a device' dialog. History - Bluetooth initially seemed OK when I first got this laptop. I was able to connect to and use my android phone as a remote with no issues. I got my first Bluetooth mouse, it paired, but after each restart, or even after sleeping, it would not 're-connect' (even though it was listed under Bluetooth devices and supposedly 'working'), and I would need to remove the device and add it again. A week or two ago it stopped working all together. It is not detected at all. I gave up on the mouse and bought another (Lenovo ThinkPad brand) only to find that it was not detected either. I subsequently tested my Android phone and discovered it would not detect either. One thing of note is under 'Devices and Printers' there is listed a 'HID Keyboard Device' which under properties is listed as a 'Bluetooth HID Device'. This was not previously there before this problem started. Each time I remove it, or uninstall it from Device Manager it will quickly re-install itself, even with all my Bluetooth devices switched off. My (Google and searching this site) research of this issue has not yielded any definitive answers. I have changed the setting under Device Manager - Bluetooth - Properties - Power Management - 'Allow the computer to turn off this device to save power' to off. I have attempted to un-install and re-install the Bluetooth hardware, including the 'remove drivers' option and downloading and running the Lenovo Bluetooth installer package (found @ http://support.lenovo.com/en_US/downloads/detail.page?DocID=DS014997). Bluetooth is turned on. All items under Bluetooth properties (Discovery and Connections) are checked. I have tried changing the batteries. I'm not sure what else I can try, apart from perhaps doing a fresh install of Windows. Any suggestions?

  Read the article

• Dell PowerEdge R720 - Corrupted RAID

  - by BT643

  Apologies in advance for the lengthy question. We have a Dell PowerEdge R720 server with: 2 x 136GB SAS drives in RAID 1 for the OS (Ubuntu Server 12.04) 6 x 3TB SATA drives in RAID 5 for data A few days ago we were getting errors when trying to access files on the large RAID 5 partition. We rebooted the server and got a message about the raid controller has found a foriegn config. We've had this before, and just needed to use Dell's RAID configuration utility to import foreign config on the RAID. Last time this worked, but this time, it started doing a disk check then we got this: FSCK has returned the following: "/dev/sdb1 inode 364738 has a bad extended attribute block 7 /dev/sdb1 unexpected inconsistency run fsck manually (i.e without -a or -p options) MOUNTALL fsck /ourdatapartition [1019] terminated with status 4 MOUNTALL filesystem has errors /ourdatapartition errors where found while checking the disk drive for /ourdatapartition Press F to fix errors, I to Ignore or M for Manual Recovery" We pressed F to try and fix the errors, but it eventually errored with: Inode 275841084, i_blocks is 167080, should be 0. Fix? yes Inode 275841141 has an invalid extend node (blk 2206761006, lblk 0) Clear? yes Inode 275841141, i_blocks is 227872, should be 0. Fix? yes Inode 275842303 has an invalid extend node (blk 2206760975, lblk 0) Clear? yes .... Error storing directory block information (inode=275906766, block=0, num=2699516178): Memory allocation failed /dev/sdb1: ***** FILE SYSTEM WAS MODIFIED ***** e2fsck: aborted /dev/sdb1: ***** FILE SYSTEM WAS MODIFIED ***** mountall: fsck /ourdatapartition [1286] terminated with status 9 mountall: Unrecoverable fsck error: /ourdatapartition We noticed one of the drive lights was not lit at all, and thought this may have failed and be the problem. We replaced the drive with a spare, and tried "F" to repair it again, but we keep just getting the same error as above. In the RAID configuration utility, all drives show as "online" and "optimal". We do have this data on another replicated server, so we're not worried about "recovering" anything, we just want to get the system back online asap. The server has 64 or 32GB memory, can't remember off the top of my head, but either way, with a 14TB RAID, I think it may still not be enough. Thanks EDIT - I checked the memory usage while fsck was running as suggested and after 2 or 3 minutes, it looked like this, using up nearly all of our servers memory: When it failed after 5 minutes or so with the error in my post, the memory immediately freed up again:

  Read the article

• Vista stuck at "Shutting down..." screen. Any way to get verbose logging?

  - by CapBBeard

  Hi all, My home machine has been running fine for about 3 years, no problems at all. Within the last couple of weeks it's had real trouble trying to shut down. It'll get so far and then just sit there at the "Shutting down..." screen for hours. I've left it overnight, I've tried in safe mode, all to no avail. These days, I just wait for the disk activity to finish up and then hold the power button to turn it off. Feels dirty as, especially because there's a RAID involved! The hardware itself is in pretty good shape and of decent spec; Core 2 Quad, 4GB RAM, 1TB RAID 1+0, so it's not quite like a 7 year old PC coming to end of life! In the last month, hardware hasn't changed except for a new monitor. Admittedly I haven't tried unplugging the monitor but I've never heard of that preventing a shutdown. I might give it a whirl later I guess, as a last resort. I've uninstalled old apps, done updates, checked the event log, looked in device manager, uninstalled all non-present devices, disabled various non-critical devices (imaging, audio etc), unplugged peripherals, stopped non-essential services, unplugged the network, disabled the network adapter entirely, ran chkdsk, verified my RAID, the list goes on. But not a single lead. I'm pretty stumped. It could be hardware, but I have no other evidence to suggest so; when the PC is running, it runs fine. Temperatures are good, gaming is smooth as always, disk performance is fine. Event log even makes it look like the shutdown was completed (gets to the point where the event log service stops). In fact, the PC doesn't appear to realise that I cut the power to it. So my question is, does anyone know if there is a way I can get some verbose output (or a log) from shutdown to give me some idea of what is causing the issue? I'm guessing it's stuck unloading some app/driver but it would be good to get some specifics! Unless anyone has any other ideas? I suspect a reinstall would resolve the issue, however I'm looking to get a new PC built in the next month or so, and the reinstall is going to be quite a big job so I'd rather just wait until then if it comes to that. Would still be nice to get this sorted in the mean time though. Cheers!

  Read the article

• Add user in CentOS 5

  - by Ron

  I created a new user in my CentOS web server with useradd. Added a password with passwd. But I can't log in with the user via SSH. I keep getting 'access denied'. I checked to make sure that the password was assigned and that the account is active. /var/log/secure shows the following error: Aug 13 03:41:40 server1 su: pam_unix(su:auth): authentication failure; logname= uid=500 euid=0 tty=pts/0 ruser=rwade rhost= user=root Please help, Thanks Thanks for the responses so far: I should add that it is a VPS on a remote computer, fresh out of the box. I can log in as the root user quite fine. I can also su to the new user, but I cannot log in as the new user. Here is my sshd_config file: # $OpenBSD: sshd_config,v 1.73 2005/12/06 22:38:28 reyk Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/usr/local/bin:/bin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. #Port 22 #Protocol 2,1 Protocol 2 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh/ssh_host_rsa_key #HostKey /etc/ssh/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 768 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH SyslogFacility AUTHPRIV #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes #StrictModes yes #MaxAuthTries 6 #RSAAuthentication yes #PubkeyAuthentication yes #AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no PasswordAuthentication yes # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes ChallengeResponseAuthentication no # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no GSSAPIAuthentication yes #GSSAPICleanupCredentials yes GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication mechanism. # Depending on your PAM configuration, this may bypass the setting of # PasswordAuthentication, PermitEmptyPasswords, and # "PermitRootLogin without-password". If you just want the PAM account and # session checks to run without PAM authentication, then enable this but set # ChallengeResponseAuthentication=no #UsePAM no UsePAM yes # Accept locale-related environment variables AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL #AllowTcpForwarding yes #GatewayPorts no #X11Forwarding no X11Forwarding yes #X11DisplayOffset 10 #X11UseLocalhost yes #PrintMotd yes #PrintLastLog yes #TCPKeepAlive yes #UseLogin no #UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #ShowPatchLevel no #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner /some/path # override default of no subsystems Subsystem sftp /usr/libexec/openssh/sftp-server

  Read the article

• 40k Event Log Errors an hour Unknown Username or bad password

  - by ErocM

  I am getting about 200k of these an hour: An account failed to log on. Subject: Security ID: SYSTEM Account Name: TGSERVER$ Account Domain: WORKGROUP Logon ID: 0x3e7 Logon Type: 4 Account For Which Logon Failed: Security ID: NULL SID Account Name: administrator Account Domain: TGSERVER Failure Information: Failure Reason: Unknown user name or bad password. Status: 0xc000006d Sub Status: 0xc0000064 Process Information: Caller Process ID: 0x334 Caller Process Name: C:\Windows\System32\svchost.exe Network Information: Workstation Name: TGSERVER Source Network Address: - Source Port: - Detailed Authentication Information: Logon Process: Advapi Authentication Package: Negotiate Transited Services: - Package Name (NTLM only): - Key Length: 0 This event is generated when a logon request fails. It is generated on the computer where access was attempted. The Subject fields indicate the account on the local system which requested the logon. This is most commonly a service such as the Server service, or a local process such as Winlogon.exe or Services.exe. The Logon Type field indicates the kind of logon that was requested. The most common types are 2 (interactive) and 3 (network). The Process Information fields indicate which account and process on the system requested the logon. The Network Information fields indicate where a remote logon request originated. Workstation name is not always available and may be left blank in some cases. The authentication information fields provide detailed information about this specific logon request. - Transited services indicate which intermediate services have participated in this logon request. - Package name indicates which sub-protocol was used among the NTLM protocols. - Key length indicates the length of the generated session key. This will be 0 if no session key was requested. On my server... I changed my adminstrative username to something else and since then I've been inidated with these messages. I found on http://technet.microsoft.com/en-us/library/cc787567(v=WS.10).aspx that the 4 means "Batch logon type is used by batch servers, where processes may be executing on behalf of a user without their direct intervention." which really doesn't shed any light on it for me. I checked the services and they are all logging in as local system or network service. Nothing for administrator. Anyone have any idea how I tell where these are coming from? I would assume this is a program that is crapping out... Thanks in advance!

  Read the article

• System failure - need diagnostic recommendation

  - by Ladislav Mrnka

  I have big problem with my computer. Configuration is: Intel i7 + 6x2GB OCZ DDR3 Motheboard: Asus P6T Deluxe V2, HDD controller configured to AHCI Main drive: OCZ Vertex 2 (SSD) - contains all installed programs and system Second drive: Samsung SpinPoint - contains User profiles, ProgramData, virtual machines and databases Third drive: Samsung SpinPoint - data drive + backups OS: Windows 7 Ultimate x64 I have never had any problem with this computer until now. During weekend my computer completely crashed without any reason. Each time I tried to boot to Windows I got BSOD with message BAD_SYSTEM_CONFIG_INFO and automatic restart (I didn't install any new SW or HW). But after restart main OCZ drive was disconnected (not detected by BIOS). When I turned off and on computer, the drive was again connected. It also happend every single time I tried to repair installation somehow. It ended with some error and after restart drive was disconnected. The only thing which worked was format + fresh install. After installing almost everything I wanted to install Visual Studio 2010 Ultimate (complete installation without SQL Server Express). During installation of VS itself I always get BSOD - it is too fast so I'm not able to read description. After restart it searches for all disk drives for really long time and sometimes it changes boot drive so the system is not able to start - Bootmgr not found. After reconfiguring BIOS the system starts. There is no event describing the failure in Event viewer. Installing VS 2010 is absolutely necessary for me. I need help with diagnostic. I need to find where is the problem - I expect that the problem is in OCZ drive or in HDD controller on motherboard but I don't know how to find it. All components still have valid warranty. Can you recommend me some approach or tools to find the problem? Edit: I'm still looking for source of the problem. New information is that Windows are not able to perform check disk (Chkdsk) on the SSD system drive. After restarting it always starts checking drive and in part where files are checked it fails with BSOD - BAD_SYSTEM_CONFIG_INFO. After next restart and skipping check disk tests the system runs.

  Read the article

• My smtp server is spammed?

  - by Milos

  I have a server and the postfix client on it. Since several days, I noticed a lot of processes running there. When checked, there are a lot of emails sent. Here is an example from the mail log: Aug 18 11:54:56 mem postfix/smtpd[9963]: connect from dslb-188-096-082-167.188.096.pools.vodafone-ip.de[188.96.82.167] Aug 18 11:54:56 mem postfix/smtpd[9301]: connect from unknown[186.113.45.4] Aug 18 11:54:56 mem postfix/smtpd[9963]: 525E7114012D: client=dslb-188-096-082-167.188.096.pools.vodafone-ip.de[188.96.82.167] Aug 18 11:54:56 mem postfix/cleanup[9970]: 525E7114012D: message-id=<B55835C9027BFA9D16CCBB556DB2F48BB82DF004000480BA-db0c3ce8aa74446411898d0d2feb3001@email.filmforthoughtinc.com> Aug 18 11:54:56 mem postfix/qmgr[2581]: 525E7114012D: from=<[email protected]>, size=10702, nrcpt=1 (queue active) Aug 18 11:54:56 mem postfix/smtpd[9301]: EC52711401DC: client=unknown[186.113.45.4] Aug 18 11:54:57 mem postfix/smtpd[9963]: disconnect from dslb-188-096-082-167.188.096.pools.vodafone-ip.de[188.96.82.167] Aug 18 11:54:57 mem postfix/cleanup[8597]: EC52711401DC: message-id=<4C905D97606B436FE50C6F738DE014D9D84F2185BA815D81-1a4dbe6fc2bfcc8183f5faf901cfa15e@email.manguerasespecializadas.com> Aug 18 11:54:57 mem postfix/smtp[9971]: 525E7114012D: to=<[email protected]>, relay=mail.mdpi.com[209.237.236.228]:25, delay=1.2, delays=0.55/0/0.45/0.16, dsn=5.1.1, status=bounced (host mail.mdpi.com[209.237.236.228] said: 550 5.1.1 <[email protected]>: Recipient address rejected: mdpi.com (in reply to RCPT TO command)) Aug 18 11:54:57 mem postfix/cleanup[10067]: 8B1E11140268: message-id=<[email protected]> Aug 18 11:54:57 mem postfix/bounce[10001]: 525E7114012D: sender non-delivery notification: 8B1E11140268 Aug 18 11:54:57 mem postfix/qmgr[2581]: 8B1E11140268: from=<>, size=12693, nrcpt=1 (queue active) Aug 18 11:54:57 mem postfix/qmgr[2581]: 525E7114012D: removed Aug 18 11:54:57 mem postfix/qmgr[2581]: EC52711401DC: from=<[email protected]>, size=10978, nrcpt=1 (queue active) Aug 18 11:54:57 mem postfix/smtp[10013]: connect to aspmx.l.google.com[2607:f8b0:400d:c03::1b]:25: Network is unreachable Aug 18 11:54:57 mem postfix/smtpd[9301]: disconnect from unknown[186.113.45.4] Aug 18 11:54:58 mem postfix/smtp[10013]: 8B1E11140268: to=<[email protected]>, relay=aspmx.l.google.com[74.125.22.26]:25, delay=0.5, delays=0.06/0/0.28/0.16, dsn=5.1.1, status=bounced (host aspmx.l.google.com[74.125.22.26] said: 550-5.1.1 The email account that you tried to reach does not exist. Please try 550-5.1.1 double-checking the recipient's email address for typos or 550-5.1.1 unnecessary spaces. Learn more at 550 5.1.1 http://support.google.com/mail/bin/answer.py?answer=6596 l7si24621420qad.26 - gsmtp (in reply to RCPT TO command)) Aug 18 11:54:58 mem postfix/qmgr[2581]: 8B1E11140268: removed Aug 18 11:54:58 mem postfix/smtp[9971]: EC52711401DC: to=<[email protected]>, relay=mail.mdpi.com[209.237.236.228]:25, delay=1.2, delays=0.66/0/0.44/0.12, dsn=5.1.1, status=bounced (host mail.mdpi.com[209.237.236.228] said: 550 5.1.1 <[email protected]>: Recipient address rejected: mdpi.com (in reply to RCPT TO command)) Aug 18 11:54:58 mem postfix/cleanup[9970]: 414361140254: message-id=<[email protected]> Aug 18 11:54:58 mem postfix/bounce[10001]: EC52711401DC: sender non-delivery notification: 414361140254 Aug 18 11:54:58 mem postfix/qmgr[2581]: 414361140254: from=<>, size=13057, nrcpt=1 (queue active) Aug 18 11:54:58 mem postfix/qmgr[2581]: EC52711401DC: removed Aug 18 11:55:01 mem postfix/smtp[10002]: 414361140254: to=<[email protected]>, relay=manguerasespecializadas.com[99.198.96.210]:25, delay=2.9, delays=0.04/0/2.1/0.84, dsn=2.0.0, status=sent (250 OK id=1XJPGs-0007BE-OI) Aug 18 11:55:01 mem postfix/qmgr[2581]: 414361140254: removed IS my server attacked, spammed? How to check that? Thank you.

  Read the article

• Graphics card artifacting

  - by White Phoenix

  This is my current build: EVGA X58 (first generation) motherboard Intel i7 965 @ stock clocks 3x 2GB DDR3-1600 Corsair RAM at stock timings and voltages Corsair AX750 80 Plus Gold PSU 1 Optical Drive 1 Seagate 7200.10 500 GB drive 2x Western Digital Caviar Black 1 TB drives OCZ Vertex 1 60 GB EVGA GTX 460 Antec 1200 case HT-Omega Striker 7.1 Sound Card Windows 7 32-bit Professional (PAE Enabled) My graphics card started artifacting while I was playing a game. It artifacted, the display blinked, then I got an NVIDIA driver has crashed and recovered message. Kept going, more artifacts, another crash, but this time my display blanked out and I couldn't do anything. Restarted my computer - artifacting is in the BIOS - got to Windows 7 but it BSOD'd before I could even log in. I restarted the computer again - artifacts cleared themselves out and I managed to get to Win7, but it soon started blinking in and out and artifacting again. Checked the card temps and they're well within range. (50 idle, 70 full load) The ambient temperature here is about 80-85F with high humidity. Tried Safe Mode and it still froze up/BSOD'd. Already tried the following to fix this problem: - Reseat the graphics card and swapped in a different slot. - Removed cover on card and sprayed with compressed air to clean it out. - Swapped around memory and/or went with only using one stick at a time. - Underclocked card I called EVGA Tech Support and they said that the voltage on the 12V rail of my Corsair AX750 PSU was on the high end of the "acceptable" range (12.4V, highest within acceptable range is 12.6V - optimal is obviously 12V). They gave me an RMA number anyway, but I want to get a second opinion from you all before I send this thing off, as shipping from where I live to EVGA is kind of pricey. This PSU is only 6 months old. So that I don't have to play RMA tag, which case would be most likely? I'm strapped for cash at the moment so I want to reduce the amount of RMAs I have to do since shipping is expensive here. Is there any surefire way to test to see if it's really the graphics card or the PSU? I tried unplugging any devices that were connected to the 12V rail (except for my SSD and graphics card) as I do have 3 mechanical hard drives, but the voltage for that rail didn't drop (it remained at 12.4V). I'm fairly sure it isn't the drivers since I'm getting the artifacting at the BIOS too. Right now I'm back in Windows 7 but I don't know for how long until it messes up again. Any ideas?

  Read the article

• SSH: Port Forwarding, Firewalls, & Plesk

  - by Kian Mayne

  I edited my SSH configuration to accept connections on Port 213, as it was one of the few ports that my work firewall allows through. I then restarted sshd and everything was going well. I tested the ssh server locally, and checked the sshd service was listening on port 213; however, I still cannot get it to work outside of localhost. PuTTY gives a connection refused message, and some of the sites that allow check of ports I tried said the port was closed. To me, this is either firewall or port forwarding. But I've already added inbound and outbound exceptions for it. Is this a problem with my server host, or is there something I've missed? My full SSH config file, as requested: # $OpenBSD: sshd_config,v 1.73 2005/12/06 22:38:28 reyk Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/usr/local/bin:/bin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. Port 22 Port 213 #Protocol 2,1 Protocol 2 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh/ssh_host_rsa_key #HostKey /etc/ssh/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 768 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH SyslogFacility AUTHPRIV #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes #StrictModes yes #MaxAuthTries 6 #RSAAuthentication yes #PubkeyAuthentication yes #AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no PasswordAuthentication yes # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes ChallengeResponseAuthentication no # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no GSSAPIAuthentication yes #GSSAPICleanupCredentials yes GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication mechanism. # Depending on your PAM configuration, this may bypass the setting of # PasswordAuthentication, PermitEmptyPasswords, and # "PermitRootLogin without-password". If you just want the PAM account and # session checks to run without PAM authentication, then enable this but set # ChallengeResponseAuthentication=no #UsePAM no UsePAM yes # Accept locale-related environment variables AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL #AllowTcpForwarding yes #GatewayPorts no #X11Forwarding no X11Forwarding yes #X11DisplayOffset 10 #X11UseLocalhost yes #PrintMotd yes #PrintLastLog yes #TCPKeepAlive yes #UseLogin no #UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #ShowPatchLevel no #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner /some/path # override default of no subsystems Subsystem sftp /usr/libexec/openssh/sftp-server

  Read the article

• Init script & the green [ OK ]

  - by Lord Loh.

  I am trying to install fast-cgi for nginx on an EC2 instance. I followed the steps explained here, but that is meant for Debian and does not work out of the box for a red-hat based system. I modified the script a bit to look like - #!/bin/bash ### BEGIN INIT INFO # Provides: php-fcgi # Required-Start: $nginx # Required-Stop: $nginx # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Short-Description: starts php over fcgi # Description: starts php over fcgi ### END INIT INFO . /etc/rc.d/init.d/functions (( EUID )) && echo .You need to have root priviliges.. && exit 1 BIND=/tmp/php.socket USER=nginx PHP_FCGI_CHILDREN=15 PHP_FCGI_MAX_REQUESTS=1000 PHP_CGI=/usr/bin/php-cgi PHP_CGI_NAME=`basename $PHP_CGI` PHP_CGI_ARGS="- USER=$USER PATH=/usr/bin PHP_FCGI_CHILDREN=$PHP_FCGI_CHILDREN PHP_FCGI_MAX_REQUESTS=$PHP_FCGI_MAX_REQUESTS $PHP_CGI -b $BIND" RETVAL=0 start() { echo -n "Starting PHP FastCGI: " #ORIGINAL LINE #daemon $PHP_CGI --quiet --start --background --chuid "$USER" --exec /usr/bin/env -- $PHP_CGI_ARGS #MODIFIED LINE daemon --user=$USER $PHP_CGI -b $BIND& RETVAL=$? echo [ $RETVAL -eq 0 ] && touch /var/lock/subsys/php-fcgi #echo "$PHP_CGI_NAME." } stop() { echo -n "Stopping PHP FastCGI: " killall -q -w -u $USER $PHP_CGI RETVAL=$? echo "$PHP_CGI_NAME." rm /var/lock/subsys/php-fcgi } case "$1" in start) start ;; stop) stop ;; restart) stop start ;; *) echo "Usage: php-fastcgi {start|stop|restart}" exit 1 ;; esac exit $RETVAL The problem I have now is - service php-fcgi start keeps the shell blocked. If I run service php-fcgi start & and then ps aux, I see the php-cgi process running bound to the socket. I see the start command stop only when I execute service php-fcgi stop. How do I solve this blocking issue? I have tried adding an & at the end of the line spawning the daemon. But other scripts do not seem to be doing this. This is the most complicated script I am attempting to modify yet :-( How do I get the script to display the green [ OK ]? I checked scripts like httpd and saw that all they were doing was something as shown below. But I never see a green [ OK ] when I execute php-fcgi. I also discovered that putting echo_success with functions sourced displays the green [ OK ] but I do not see any other scripts in the /etc/rc.d/init.d/ executing echo_success or echo_failure. What have I got wrong? Also, How do i specify PHP_FCGI_CHILDREN with daemon? echo [ $RETVAL -eq 0 ] && touch /var/lock/subsys/

  Read the article

• VIM "upgraded" to expandtab and tabstop=8 on Python files

  - by dotancohen

  After reinstalling my OS from Kubuntu 12.10 to Kubuntu 14.04, VIM has changed its behaviour when editing Python files. Though before the reinstall all file types had noexpandtab and tabstop=4 set, now in Python those values are expandtab and tabstop=8, checked also via VIM behaviour and also via asking VIM set foo?. Non-Python files retain the noexpandtab and tabstop=4 behaviour that I prefer. The .vim direcotry and .vimrc were not touched during the reinstall. It can be seen that no files in .vimrc have been touched in months (with the exception of the irrelevant .netrwhist): - bruno():~$ ls -lat ~/.vim total 68 drwxr-xr-x 85 dotancohen dotancohen 12288 Aug 25 13:00 .. drwxr-xr-x 12 dotancohen dotancohen 4096 Aug 21 11:11 . -rw-r--r-- 1 dotancohen dotancohen 268 Aug 21 11:11 .netrwhist drwxr-xr-x 2 dotancohen dotancohen 4096 Mar 6 18:31 plugin drwxr-xr-x 2 dotancohen dotancohen 4096 Mar 6 18:31 doc drwxrwxr-x 2 dotancohen dotancohen 4096 Nov 29 2013 syntax drwxrwxr-x 2 dotancohen dotancohen 4096 Nov 29 2013 ftplugin drwxr-xr-x 4 dotancohen dotancohen 4096 Nov 29 2013 autoload drwxrwxr-x 5 dotancohen dotancohen 4096 May 27 2013 after drwxr-xr-x 2 dotancohen dotancohen 4096 Nov 1 2012 spell -rw------- 1 dotancohen dotancohen 138 Aug 14 2012 .directory -rw-rw-r-- 1 dotancohen dotancohen 190 Jul 3 2012 .VimballRecord drwxrwxr-x 2 dotancohen dotancohen 4096 May 12 2012 colors drwxrwxr-x 2 dotancohen dotancohen 4096 Mar 16 2012 mytags drwxrwxr-x 2 dotancohen dotancohen 4096 Feb 14 2012 keymap Though .vimrc has been touched since the reinstall, it was only me testing to see where the problem is. How can I tell what is settingexpandtab and tabstop? Side note: I'm not even sure what I should read in the built-in help for this issue. I started with ":h plugin" but that did not help other than showing me that the following plugins are loaded (possibly relevant): standard-plugin-list Standard plugins pi_getscript.txt Downloading latest version of Vim scripts pi_gzip.txt Reading and writing compressed files pi_netrw.txt Reading and writing files over a network pi_paren.txt Highlight matching parens pi_tar.txt Tar file explorer pi_vimball.txt Create a self-installing Vim script pi_zip.txt Zip archive explorer LOCAL ADDITIONS: local-additions DynamicSigns.txt - Using Signs for different things NrrwRgn.txt A Narrow Region Plugin (similar to Emacs) fugitive.txt A Git wrapper so awesome, it should be illegal indent-object.txt Text objects based on indent levels. taglist.txt Plugin for browsing source code vimwiki.txt A Personal Wiki for Vim

  Read the article

• Windows Server 2003 Standard R2 CD 1 cannot boot: freeze at No Emulation

  - by TGP1994

  Hi everyone. I've been interested in the Windows Server line of OSes, so since I apply for DreamSpark, I thought I'd go download it and try it. I just so happened to have an old desktop that I was using awhile ago for Windows XP, so I imaged the drive in preparation for it to be overwritten with the new OS. (This system has an Asus A7V8X-X motherboard, an AMD Athlon XP 2800+ processor, and 1GB of RAM.) I tried burning the first disk image on my newer desktop computer, running Windows XP, although the CD burner consistently failed at a particular track area from cd to cd, so it seemed like the burner was toast there. Fortunately, I had a laptop, so I transferred the images over to that, then burned the first disc there. First time around went great, and the burning program reported no errors. I then took the CD over to the computer that I was intending to install Server onto, set the BIOS to boot from the CD drive, then I booted it up. Like normal, after the POST, it printed "Boot from ATAPI CD-Rom: No Emulation", which I was used to seeing with bootable cds. I waited for the "Press any key to continue..." message that I had become so familiar with in windows discs, although I saw none. The computer sat there for about 5 seconds with the cd spinning, then it spun down like it was done reading it. Nothing else happened. No response from the keyboard. I tried again, same result. I then downloaded IMGBurn, and I put the burned cd into the laptop that burned it originally. I also downloaded a fresh image from the dreamspark site. I ran a verify session, and everything checked out. I later tried getting various DOS startup discs, then I tried booting the winnt binary, which supposedly initiates the installation process. Either the shells reported that not enough memory was available (since they would be running in low memory mode), or FreeDOS in particular would report Illegal instructions right away. Is the image corrupt at dreamspark, or am I doing something wrong?

  Read the article

• One user sometimes gets an unknown certificate error opening Outlook

  - by Chris

  Let me clarify a little. This isn't an unknown certificate error it's an unknown certificate error in so much as I can't figure out where the certificate comes from. This happens on a Win 7 Enterprise machine connecting to Exchange 2010 with Outlook 2010. The error he gets is that the root is not trusted because it's a self-signed cert. Take a look at this screenshot because even if I had generated this myself I wouldn't have put "SomeOrganizationalUnit" or "SomeCity" or "SomeState", etc. (Red block covers our domain name.) I'm a little concerned this is a symptom of a security breach. Exchange 2010 has three certificates installed but none of them are this certificate. They all have different expiration dates (one is expired) and different meta-data. edit: There are two scenarios that I see the certificate warning and one of them I can reliably repeat. When the user leaves his computer on over night Outlook pops the Security Warning window. I don't know what time this happens. Using Outlook Anywhere if I connect to Exchange externally via a cellular USB modem the Security Warning window will appear every time I close and reopen Outlook. Whether I say Yes or No does not make a difference on whether or not I can connect to Exchange and send/receive email. In other words, I can always connect to Exchange. I've checked my two Exchange servers and my Cisco router for a certificate that matches this one and I can't find it. edit 2: Here is a screenshot of the Security Alert window. (I've been calling it Security Warning... My mistake.) edit 3: I stopped seeing this error several weeks ago but I can't tie it to any single event (because I just sort of realized that warning had stopped showing up) but I think I found the source of the certificate. Last week I found out that the certificate on our website DomainA.com was invalid. I knew that our web admin had installed a valid certificate so when I look into the problem I found out I was being presented with the invalid certificate that this posting is in regards to. The Exchange server's domain is mail.DomainA.com so I can only guess that Outlook was passing this invalid certificate through as it did some kind of check on DomainA.com. This issue is still a mystery because the certificate warning stopped appearing several weeks ago whereas the invalid certificate issue on the website was only fixed last week. It ended up being a problem with the website control panel. The valid certificate was installed but not being served for some reason and instead the self-signed cert was being served.

  Read the article

• Set up Gmail with Google apps for own domain

  - by erdomester

  I rent a server from a German company. I have remote access to it as well as WHM and CPanel. I decided to use Google's mail servers for obvious reasons. I am not an admin just an average guy trying to set up what needs to be set up. The problem is I am unable to make the necessary settings. I watched Youtube tutorials, followed written ones as well as Google's help, but there is (at least) one serious problem with my domain settings. The domain console alwasy says Your MX records are incorrect When I check dappwall.com in mxtoolbox.com it says Pref Hostname IP Address TTL 10 mail.dappwall.com 46.4.88.247 24 hrs But this is not the host name. I checked WHM and my hostname is server1.dappwall.com. I can confirm it by typing the hostname command in putty. However, if I do an mx lookup at mxtoolbox.com on server1.dappwall.com or mail.dappwall.com I get Lookup failed after 1 name servers timed out or responded non-authoritatively I ran checks on the google apps toolbox on dappwall.com and two problems emerged: 1.No Google mail exchangers found. Relayhost configuration? 10 mail.dappwall.com In Google Apps > Settings for Gmail > Advanced settings it also says that my current MX records for dappwall.com is Priority Points to 10 MAIL.DAPPWALL.COM. So mail.dappwall.com again. I also have access to a robot provided by the company I rent the server from. Here I see this mail at two places but how should I (if it's necessary) modify this? I set Email routing to Automatically Detect Configuration. 2.There SHOULD be a valid SPF record. "v=spf1 include:_spf.google.com ~all" In the DNS Zone Editor I added this spf record: Name TTL Class Type Record dappwall.com. 1440 IN TXT v=spf1 include:_spf.google.com ~all In the cPanel Email Authentication page it says SPF: Status: Enabled Warning: cPanel is unable to verify that this server is an authoritative nameserver for dappwall.com. [?] Your current raw SPF record is : v=spf1 include:_spf.google.com ~all How can I confirm that my server is an authoritative nameserver for dappwall.com? In WHM Service Configuration Mailserver selection Dovecot was set but I disabled it (i don't know if that's ok). What am I missing here? Where is that mail.dappwall.com coming from?

  Read the article

• Trouble creating FTP in Server 2008

  - by Saariko

  I have been trying to create an FTP server on my new Server 2008. I have been following both (very detailed and highly published here guides) For setting up using IIS Manager http://learn.iis.net/page.aspx/321/configure-ftp-with-iis-7-manager-authentication/ and For anonymous FTP http://www.trainsignaltraining.com/windows-server-2008-ftp-iis7 I am able to log as an anonymous user. My need is to use a named user, so I need to use the IIS Manager. I get error 530 when trying to log as a user. Connected to 127.0.0.1. 220 Microsoft FTP Service User (127.0.0.1:(none)): ftpmanager 331 Password required for ftpmanager. Password: 530-User cannot log in. Win32 error: Logon failure: unknown user name or bad password. Error details: Filename: Error: 530 End Login failed. ftp> I can not learn from this message anything. My password is set to: 1234 (so I don't think I make a mistake here - testing purposes only ofc) Thank you. Note - I went over other posts on SE that I read, and couldn't get the result: IIS7 Windows Server 2008 FTP -> Response: 530 User cannot log in. FTP Error 530, User cannot log in, home directory inaccessible. Having trouble setting up FTP server on Windows Server 2008 EDIT I think I found some errors with the physical path. Going to Basic settings, and Test Connection on the physical path, gave me the following error: The server is configured to use pass-through authentication with a built-in account to access the specified physical path. However, IIS Manager cannot verify whether the built-in account has access. Make sure that the application pool identity has Read access to the physical path. If this server is joined to a domain, and the application pool identity is NetworkService or LocalSystem, verify that \$ has Read access to the physical path. Then test these settings again. I am not sure which/whom should get access to the Root folder !? I want to point out, I managed to login with a domain user (change authorization and authentication methods) but this is NOT the requested solution. I checked to make sure that the FTP, folders, access is working properly. I am bit lost here. ==== More tries: I have enabled another Allow rule for ALL Users. I still get the same error. It seems that it doesn't matter if i use a correct or wrong password, I still get Error 530.

  Read the article

• Windows 7 & Virtual PC and Internet (gateway) problems on host PC

  - by Mufasa

  I upgraded to Windows 7 on a PC that is a few years old. The CPU was one revision away from having Hyper-V on it. So, I had to install Microsoft Virtual PC 2007 (v6.0.156.0) to run full XP instances instead of the seamless XP virtualization that is advertised so much. That's fine though; the 'older' version is useful since I use it to run different versions of the whole XP/IE stack for testing. (I'm a web developer.) ...And for the one 16-bit application we still use at the office for scheduling. * sigh * The virtual instances work fine, including networking. My issue is that after a reboot or coming out of sleep mode, my host Windows 7 won't connect to the Internet. It will connect to the local network fine. If I disable the "Virtual Machine Network Services" item (I'll call "VMNS" from here on) in the LAN Connection properties box, it starts working. But than the Virtual PC instances lose their network connectivity. If I re-enable VMNS again in the same instance, everything works (Internet on host and in the virtualized instances). But after the next reboot/sleep cycle this starts over. The route table gave me a clue though. When doing a cycle w/ VMNS enabled: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 On-link 10.0.3.51 20 0.0.0.0 0.0.0.0 10.0.10.10 10.0.3.51 276 ... After VMNS is disabled, the first route goes away. I assume that is for VMNS to intercept virtualized instance's network connections and forward them correctly? Just a guess though. More info: I checked my Firewall settings and Services (because I'm sort of a control nazi and turn off a lot) but couldn't find anything that made sense and if turned on changed anything. So it might be something there I'm missing, but I don't know what. My current hacked solution: So, I figured I'd mess with the routes myself to see if that helped, it did. If I run a route delete 0.0.0.0 on the universal (0.0.0.0) gateway routes, and add back in just the 2nd line with route add 0.0.0.0 mask 0.0.0.0 10.0.10.10--the one that points to my actual gateway (10.0.10.10)--then I don't have to mess with the disable/enable cycle of VMNS, and everything works. Running those two commands is faster then bringing up connection options and disabling and re-enabling VMNS, but I still don't want to have use that hack script every boot either. (Oh, and I also tried messing with hard-coding TCP/IP settings in my network adapter, including setting high metrics, etc., but that didn't help either.) Any suggestions on the right way to fix this?

  Read the article

• Trying to get DNS services running on Windows Server 2008 R2, what am I getting wrong ?

  - by LaserBeak

  Ok, So I am basically trying to get a home server pc up that will provide Domain name services, act as Mail server and web server. I have one static IP, well it's not officially static but hasn't changed in two years so I'll call it static. I have done the following: Configured router NAT/virtual port forward UDP/TCP port 53 to the internal IP of my server 192.168.1.16, in adapter settings specified the manual settings: 192.168.1.16 IP, gateway 192.168.1.1, Subnet: 255.255.255.0 and loopback DNS: 127.0.0.1 Using my public my public IP Checked using http://www.canyouseeme.org/ that port 53 is open and is not being blocked by my ISP. It can see services on this port. Registered Domain name (mydomain.com.au) Updated whois database through the domain registrars site and registered NameServer names: ns0.mydomain.com.au and ns2.mydomain.com.au, both have been associated with my single public IP. (Waited 24 hours) Update the nameserver for mydomain.com.au: primary ns0.mydomain.com.au secondary: ns2.mydomain.com.au (waited 24+ hours) Installed Server 2008 R2, install web server role and DNS role. Webserver works when I enter my public IP into browser of any PC/mobile, get IIS7 welcome page. In DNS server: Created new forward lookup zone: ; ; Database file mydoman.com.au.dns for mydomain.com.au zone. ; Zone version: 10 ; @ IN SOA mydomain.com.au. mydomain.testdomain.com. ( 10 ; serial number 900 ; refresh 600 ; retry 86400 ; expire 3600 ) ; default TTL ; ; Zone NS records ; @ NS ns0.mydomain.com.au. @ NS ns1.mydomain.com.au. ; ; Zone records ; @ A 192.168.1.16 www A 192.168.1.16 The Domain name services will however not work, the whois database updated with ns0.mydomain.com.au etc. but when I type in my site name www.mydomain.com.au from an external machine it will not open site and I can't even ping it (Can't find host) When I check the ns0.mydomain.com.au NS record using a tool Like: http://www.squish.net/dnscheck/ I get: Security: Server ns0.mydomain.com.au (XXX.XXX.XXX.XX <- my public IP) is recursive Domain exists but there is no such record Any ideas, thanks...

  Read the article

• 1600+ 'postfix-queue' processes - OK to have this many?

  - by atomicguava

  I have a Plesk 9.5.4 CentOS server running Postfix. I had been having massive problems with the mailq being full of 'double-bounce' email messages containing errors relating to 'Queue File Write Error', but I believe these are now fixed thanks to this thread. My new problem is that when I run top, I can see lots of processes called 'postfix-queue' and have fairly high load: top - 13:59:44 up 6 days, 21:14, 1 user, load average: 2.33, 2.19, 1.96 Tasks: 1743 total, 1 running, 1742 sleeping, 0 stopped, 0 zombie Cpu(s): 5.1%us, 8.8%sy, 0.0%ni, 85.3%id, 0.8%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 3145728k total, 1950640k used, 1195088k free, 0k buffers Swap: 0k total, 0k used, 0k free, 0k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1324 apache 16 0 344m 33m 5664 S 21.7 1.1 0:03.17 httpd 32443 apache 15 0 350m 36m 6864 S 14.4 1.2 0:13.83 httpd 1678 root 15 0 13948 2568 952 R 2.0 0.1 0:00.37 top 1890 mysql 15 0 689m 318m 7600 S 1.0 10.4 219:45.23 mysqld 1394 apache 15 0 352m 41m 5972 S 0.7 1.3 0:03.91 httpd 1369 apache 15 0 344m 33m 5444 S 0.3 1.1 0:02.03 httpd 1592 apache 15 0 349m 37m 5912 S 0.3 1.2 0:02.52 httpd 1633 apache 15 0 336m 20m 1828 S 0.3 0.7 0:00.01 httpd 1952 root 19 0 335m 28m 10m S 0.3 0.9 1:35.41 httpd 1 root 15 0 10304 732 612 S 0.0 0.0 0:04.41 init 1034 mhandler 15 0 11520 1160 884 S 0.0 0.0 0:00.00 postfix-queue 1036 mhandler 15 0 11516 1120 860 S 0.0 0.0 0:00.00 postfix-queue 1041 mhandler 17 0 11516 1156 884 S 0.0 0.0 0:00.00 postfix-queue 1043 mhandler 15 0 11512 1116 860 S 0.0 0.0 0:00.00 postfix-queue 1063 mhandler 16 0 11516 1160 884 S 0.0 0.0 0:00.00 postfix-queue 1068 mhandler 15 0 11516 1128 860 S 0.0 0.0 0:00.00 postfix-queue 1071 mhandler 17 0 11512 1152 884 S 0.0 0.0 0:00.00 postfix-queue 1072 mhandler 15 0 11512 1116 860 S 0.0 0.0 0:00.00 postfix-queue 1081 mhandler 16 0 11516 1156 884 S 0.0 0.0 0:00.00 postfix-queue 1082 mhandler 15 0 11512 1120 860 S 0.0 0.0 0:00.00 postfix-queue 1089 popuser 15 0 33892 1972 1200 S 0.0 0.1 0:00.02 pop3d 1116 mhandler 16 0 11516 1164 884 S 0.0 0.0 0:00.00 postfix-queue 1117 mhandler 15 0 11516 1124 860 S 0.0 0.0 0:00.00 postfix-queue 1120 mhandler 16 0 11516 1160 884 S 0.0 0.0 0:00.00 postfix-queue 1121 mhandler 15 0 11512 1120 860 S 0.0 0.0 0:00.00 postfix-queue 1130 mhandler 17 0 11516 1160 884 S 0.0 0.0 0:00.00 postfix-queue 1131 mhandler 15 0 11516 1120 860 S 0.0 0.0 0:00.00 postfix-queue 1149 root 17 -4 12572 680 356 S 0.0 0.0 0:00.00 udevd 1181 mhandler 16 0 11516 1160 884 S 0.0 0.0 0:00.00 postfix-queue 1183 mhandler 15 0 11512 1116 860 S 0.0 0.0 0:00.00 postfix-queue 1224 mhandler 16 0 11516 1160 884 S 0.0 0.0 0:00.00 postfix-queue 1225 mhandler 15 0 11516 1120 860 S 0.0 0.0 0:00.00 postfix-queue 1228 apache 15 0 345m 34m 5472 S 0.0 1.1 0:04.64 httpd 1241 mhandler 16 0 11516 1156 884 S 0.0 0.0 0:00.00 postfix-queue 1242 mhandler 15 0 11512 1120 860 S 0.0 0.0 0:00.00 postfix-queue 1251 mhandler 17 0 11516 1156 884 S 0.0 0.0 0:00.00 postfix-queue 1252 mhandler 15 0 11516 1120 860 S 0.0 0.0 0:00.00 postfix-queue 1258 apache 15 0 349m 37m 5444 S 0.0 1.2 0:01.28 httpd When I run ps -Al | grep -c postfix-queue it returns 1618! My question is this: is this normal or is there something else going wrong with Postfix? Right now, if I run mailq it is empty, and qshape deferred / qshape active are empty too. Thanks in advance for your help.

  Read the article

• System won't boot: Gigabyte HD 7790 1GB OC GPU issue or Corsair VS550 PSU issue?

  - by MGOwen

  Installed a new GPU, and PC won't boot. Turn it on and: No monitor signal at all (tried HDMI and VGA via DVI, on 2 working monitors). CPU and GPU fans DO spin, but No system beeps, no sounds from drives (they might make a small noise in the first 1 second or so, but there's definitely no OS loading or anything like that) If hit "power off" button it turns off immediately (no holding down for 3 seconds like usual) If I put my old HD 5670 GPU back in, everything works fine. But (plot twist!) card is not totally dead. My friend put it in his PC, and it works fine (he even played a game for 15 minutes, no issues). He has a Corsair TX850 850W and a Gigabyte MB. So my main theory is: the GPU isn't getting enough power from the PSU. But is it: Bad PSU? Seems unlikely, since it works fine with the other GPU. Also, the PSU Is brand new and 550W (single 42A/504W 12V rail). Overkill for this GPU. Corsair is a decent brand, but maybe just mine is faulty? Bad GPU? Could it be drawing more power than it should be, somehow, or something? Supposedly HD 7790 needs only 21A/75W on the 12v rail, though this one is factory overclocked a bit... but should that triple the power requirement? Something else? Could there be a motherboard incompatibility somehow? Both MB and GPU are less than a year old and PCI Express 3.0 x16. Things I've tried: Re-seating the video card Testing PC with old GPU (works fine, same PCIe slot). Checked AMD's stated amp/watt requirements of a 7790 and my PSU (see above). My PSU can output twice the amps (single rail) and 5x the Wattage a 7790 needs. Here are the full specs: Gigabyte HD 7790 1GB OC GPU Corsair VS550 550W PSU 4GB RAM AsRock H61M U3S3 motherboard i3-2100 500GB SATA HDD (2007-ish) blu-ray drive (new) PCI 802.11g card Edit: Motherboard BIOS Update seems to have fixed it. (If anyone has same problem and it doesn't work, comment here).

  Read the article

• FTP server questions

  - by Brad

  I'm currently trying to set up a home FTP server using debian and proftpd and I've run into a problem that has me confused. I have most things set up already, I believe, but I cannot access my ftp server using my external ip. I've forwarded the correct port on my router and I've checked http://www.yougetsignal.com/tools/open-ports/ to be sure that it is, in fact, opened. I've used telnet locally on my server to check that the port accepts connections. I am able to use ftp via LAN. But, I still cannot access anything externally. I'm thinking that there's still some router configuration to be done in order to fix this, such as routing all connections on my ftp port to my server via the internal ip, but I can't find any option on my router to do this. Is this a necessary step? There is an option to use DMZ hosting, but I'd rather avoid it if possible. I can provide additional information as requested, please let me know any information that you think could help at all. Thanks. -Brad PS - I have a Telus Actiontec Modem/Router Update - !! Trying my ftp server out at work, worked! I guess I did set it up correctly after all. What is confusing me, though, is why doesn't the server allow me to connect locally anymore? That seems very weird to me. Also, I don't really understand why I am denied outright if I attempt to connect from the same network using the external address. I'll look into it more when I get home, but thank you guys for your help. Update 2 - I found the problem with not being able to connect locally anymore. I was setting the masquerade address to my external IP and for some reason that was causing it to hang on MLSD when I connected using my LAN address. I've removed the masquerade address and I'm going to check if I need it at work tomorrow. I'll update this page if I find anything.

  Read the article

• Single domain name potentially resolving to multiple servers

  - by Jace

  first time here at Server Fault, and I apologize in advance that this domain stuff is not really my strength. Any and all suggestions are much appreciated. I am completely lost and incredibly tired! I've inherited an incredibly convoluted system from my predecessor, and I'm trying to find a way to solve it - or I need to be told that it just isn't possible. I've got an old site on ServerA (some kind of Linux distribution), with the domain SomeDomain.com There is a new site sitting on ServerB (Ubuntu), with the intention of having SomeDomain.com to serve it in the future (it is replacing the old site) ServerA also has a web app that is currently in use by other departments within the company (accessible at SomeDomain.com/web-app/) The goal: To have SomeDomain.com and all extensions of this domain name (sub-domains, URL's etc.) serve the new site on ServerB. BUT, the URL SomeDomain.com/web-app/ must serve the Web App on ServerA. The Catch: The ServerA is a shared server with a hosting company with VERY limiting restrictions in place - I cannot adjust DNS settings (apart from Name servers - but cannot set A records or anything, I have full access to ServerB to do as I wish). Therefore the web-app MUST be served from SomeDomain.com/web-app/ and not from a sub-domain or anything. These limitations make migrating the web-app from Server A to Server B rather undesirable, AND this web-app will be replaced in the near future, so it isn't worth the effort right now. Therefore, ultimately I will want 1 domain name to resolve to Server B's IP address most of the time, but in the event that the URL is SomeDomain.com/web-app/, it should resolve to Server A's IP. Note: The domain names don't, technically, have to resolve to one IP or another - but ultimately the URL's must stay consistent Some things I have tried: I've looked into mod_rewrite and .htaccess to try and achieve this effect, but it doesn't look like it's going to work for me - but I may have done it wrong (On Server B, I just checked if the request URI was /web-app/ and tried to serve the /web-app/ folder on Server A) I do have the ability to modify the name servers on both servers I am not able to make a sub domain on Server A that points back to Server A (I assume because the hosting company's servers use the URL to determine what site the serve). I figured this could be good as I'd could set an A record on Server B to point to the web app on Server A - but alas, Server A requires SomeDomain.com. If there is any more information I can give, please let me know. I need a nudge in the right direction, ideas or a solution.

  Read the article

< Previous Page | 484 485 486 487 488 489 490 491 492 493 494 495  | Next Page >