Search Results

Search found 41497 results on 1660 pages for 'fault'.

Page 49/1660 | < Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >

• verify cert with certutil.exe

  - by Michal

  Hi, I have stupid problem, what is correct syntax on verify certificate in certificate store with certutil.exe. I have client certificate in cerstore. I try this: certutil.exe -verify CertCommonName but in finish with this error : DecodeFile returned The system cannot find the file specified. 0x80070002 (WIN32 : 2) LoadCert(Cert) returned The system cannot find the file specified. 0x80070002 (W IN32: 2) CertUtil: -verify command FAILED: 0x80070002 (WIN32: 2) CertUtil: The system cannot find the file specified. When I ping certutil.exe -ping it connect to pc.

  Read the article

• Problem with Email Notifications in VisualSVN Server

  - by emzero

  Hey guys! I have a dedicated server running windows 2003 server and Visual SVN Server 2.0.8. I'm trying to configure it to send email notifications on commit. So I found this article on Visual SVN site. It says I have to edit the Post-commit hook and set it to the following: "%VISUALSVN_SERVER%\bin\VisualSVNServerHooks.exe" ^ commit-notification "%1" -r %2 ^ --from <from-email> --to <to-email> ^ --smtp-server <smtp-server> Of course I've replaced the variables there. The problem is when someone commits something, the svn client throws the following error: post-commit hook failed (exit code 1) with no output. The commit process runs with no problems, I mean it does commit the files. But it won't send any email notification. If I remove the post-commit hook, then I don't get the error (and of course I don't get any notification). Could you help me out with it? The error doesn't tell too much =S Thank you!

  Read the article

• Macports Apache not starting at Mac osx snow leopard boot

  - by greg

  Macports Apache2 not starting at Mac Osx snow leopard boot. I've done the launchctl load command, the symlinks point to my /opt/local//etc/LaunchDaemeons/org.macports.apache2/org.macports.apache2.plist, but it never starts. I can start it manually, works fine after that. Just wont load on startup. My server is named in my /opt/localapache2/conf/httd.conf, I had read that sometimes makes a difference. I've done the launchctl unload and load trick, al with no results. I'm out of ideas.

  Read the article

• git on HTTP with gitolite and nginx

  - by Arnaud

  I am trying to setup a server where my git repo would be accessible with HTTP(S). I am using gitolite and nginx (and gitlab for web interface but I doubt it makes any difference). I have searched the whole afternoon and I think I'm stuck. I have think I have understood that nginx needs fcgiwrap to work with gitolite, so I tried several configurations, but none of them work. My repositories are at /home/git/repositories. Here's the three nginx configurations I have tried. 1: location ~ /git(/.*) { gzip off; root /usr/lib/git-core; fastcgi_pass unix:/var/run/fcgiwrap.socket; include /etc/nginx/fcgiwrap.conf; fastcgi_param SCRIPT_FILENAME /usr/lib/git-core/git-http-backend; fastcgi_param DOCUMENT_ROOT /usr/lib/git-core/; fastcgi_param SCRIPT_NAME git-http-backend; fastcgi_param GIT_HTTP_EXPORT_ALL ""; fastcgi_param GIT_PROJECT_ROOT /home/git/repositories; fastcgi_param PATH_INFO $1; #fastcgi_param PATH_TRANSLATED $document_root$fastcgi_path_info; } Result: > git clone http://myservername/projectname.git test/ Cloning into test... fatal: http://myservername/projectname.git/info/refs not found: did you run git update-server-info on the server? and > git clone http://myservername/git/projectname.git test/ Cloning into test... error: The requested URL returned error: 502 while accessing http://myservername/git/projectname.git/info/refs fatal: HTTP request failed 2: location ~ /git(/.*) { fastcgi_pass localhost:9001; include /etc/nginx/fcgiwrap.conf; fastcgi_param SCRIPT_FILENAME /usr/lib/git-core/git-http-backend; fastcgi_param GIT_HTTP_EXPORT_ALL ""; fastcgi_param GIT_PROJECT_ROOT /home/git/repositories; fastcgi_param PATH_INFO $1; } Result: > git clone http://myservername/projectname.git test/ Cloning into test... fatal: http://myservername/projectname.git/info/refs not found: did you run git update-server-info on the server? and > git clone http://myservername/git/projectname.git test/ Cloning into test... error: The requested URL returned error: 502 while accessing http://myservername/git/projectname.git/info/refs fatal: HTTP request failed 3: location ~ ^.*\.git/objects/([0-9a-f]+/[0-9a-f]+|pack/pack-[0-9a-f]+.(pack|idx))$ { root /home/git/repositories/; } location ~ ^.*\.git/(HEAD|info/refs|objects/info/.*|git-(upload|receive)-pack)$ { root /home/git/repositories; fastcgi_pass unix:/var/run/fcgiwrap.socket; fastcgi_param SCRIPT_FILENAME /usr/lib/git-core/git-http-backend; fastcgi_param PATH_INFO $uri; fastcgi_param GIT_PROJECT_ROOT /home/git/repositories; include /etc/nginx/fcgiwrap.conf; } Result: > git clone http://myservername/projectname.git test/ Cloning into test... error: The requested URL returned error: 502 while accessing http://myservername/projectname.git/info/refs fatal: HTTP request failed and > git clone http://myservername/git/projectname.git test/ Cloning into test... error: The requested URL returned error: 502 while accessing http://myservername/git/projectname.git/info/refs fatal: HTTP request failed Also note that with any of those configurations, when I try to clone with a project name that actually doesn't exist, I get a 502 error. Does anyone already succeeded in doing this? What am I doing wrong? Thanks. UPDATE: nginx error log file said: 2012/04/05 17:34:50 [crit] 21335#0: *50 connect() to unix:/var/run/fcgiwrap.socket failed (13: Permission denied) while connecting to upstream, client: 192.168.12.201, server: myservername, request: "GET /git/oct_editor.git/info/refs HTTP/1.1", upstream: "fastcgi://unix:/var/run/fcgiwrap.socket:", host: "myservername" So I changed permissions for /var/run/fcgiwrap.socket, and now I have : > git clone http://myservername/git/projectname.git test/ Cloning into test... error: The requested URL returned error: 403 while accessing http://myservername/git/projectname.git/info/refs fatal: HTTP request failed Here is the error.log file I have now: 2012/04/05 17:36:52 [error] 21335#0: *78 FastCGI sent in stderr: "Cannot chdir to script directory (/usr/lib/git-core/git/projectname.git/info)" while reading response header from upstream, client: 192.168.12.201, server: myservername, request: "GET /git/projectname.git/info/refs HTTP/1.1", upstream: "fastcgi://unix:/var/run/fcgiwrap.socket:", host: "myservername" I keep on investigating.

  Read the article

• Weird vps server issue

  - by anon-user0

  I have an unmanaged linux vps Ubuntu 11.10 (Oneiric Ocelot). I have LNMP installed. Also php-fpm php-apc, varnish, memcache. I have (or rather had) several live sites on it. under normal load the server uses ~700 mb memory. But since last night its using only 20mb~ memory and a lot of the services seems to be down (according to htop) I only see nginx working and mysql starts up and goes does every few minutes on a loop. Here are some information on the server that might help you help me: root@server:~# uname -a Linux server 2.6.18-308.el5.028stab099.3 #1 SMP Wed Mar 7 15:56:00 MSK 2012 i686 i686 i386 GNU/Linux - root@server:~# ifconfig -a lo Link encap:Local Loopback LOOPBACK MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:127.0.0.2 P-t-P:127.0.0.2 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:12515 errors:0 dropped:0 overruns:0 frame:0 TX packets:9541 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:7191214 (7.1 MB) TX bytes:536726 (536.7 KB) venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:176.31.158.78 P-t-P:176.31.158.78 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 - root@server:~# netstat -l Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 *:http-alt *:* LISTEN tcp 0 0 *:ssh *:* LISTEN tcp6 0 0 [::]:http-alt [::]:* LISTEN tcp6 0 0 [::]:ssh [::]:* LISTEN Active UNIX domain sockets (only servers) Proto RefCnt Flags Type State I-Node Path unix 2 [ ACC ] STREAM LISTENING 9307368 @/com/ubuntu/upstart - htop: http://i.stack.imgur.com/NHKYX.png EDIT: Stressed. mind was not working adding log: root@server:~# less /var/log/syslog Jun 27 05:27:42 server syslogd 1.5.0#6ubuntu1: restart. Jun 27 05:39:01 server CRON[9298]: (root) CMD ([ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) -delete) Jun 27 05:40:01 server CRON[9463]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jun 27 05:46:21 server sm-msp-queue[9480]: q5R1R7Ue004056: to=root, ctladdr=root (0/0), delay=00:19:14, xdelay=00:06:18, mailer=relay, pri=122407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 05:52:39 server sm-msp-queue[9480]: q5QMk7S9009582: to=root, ctladdr=root (0/0), delay=03:06:32, xdelay=00:06:18, mailer=relay, pri=842407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 06:00:01 server CRON[15671]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jun 27 06:06:22 server sm-msp-queue[15690]: q5R1R7Ue004056: to=root, ctladdr=root (0/0), delay=00:39:15, xdelay=00:06:18, mailer=relay, pri=212407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 06:09:01 server CRON[18114]: (root) CMD ([ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) -delete) Jun 27 06:12:40 server sm-msp-queue[15690]: q5QMk7S9009582: to=root, ctladdr=root (0/0), delay=03:26:33, xdelay=00:06:18, mailer=relay, pri=932407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 06:20:02 server CRON[21888]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jun 27 06:26:22 server sm-msp-queue[21907]: q5R1R7Ue004056: to=root, ctladdr=root (0/0), delay=00:59:15, xdelay=00:06:18, mailer=relay, pri=302407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 06:27:02 server CRON[24021]: (root) CMD (cd / && run-parts --report /etc/cron.hourly) Jun 27 06:32:40 server sm-msp-queue[21907]: q5QMk7S9009582: to=root, ctladdr=root (0/0), delay=03:46:33, xdelay=00:06:18, mailer=relay, pri=1022407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 06:39:01 server CRON[27941]: (root) CMD ([ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) -delete) Jun 27 06:40:02 server CRON[28110]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jun 27 06:46:22 server sm-msp-queue[28125]: q5R1R7Ue004056: to=root, ctladdr=root (0/0), delay=01:19:15, xdelay=00:06:18, mailer=relay, pri=392407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 06:52:40 server sm-msp-queue[28125]: q5QMk7S9009582: to=root, ctladdr=root (0/0), delay=04:06:33, xdelay=00:06:18, mailer=relay, pri=1112407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 06:52:40 server sm-msp-queue[28125]: q5QMk7S9009582: q5R2e4uo028125: sender notify: Warning: could not send message for past 4 hours Jun 27 06:52:44 server sm-msp-queue[28125]: q5R2e4uo028125: to=root, delay=00:00:04, xdelay=00:00:04, mailer=relay, pri=33690, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 07:00:02 server CRON[1543]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jun 27 07:06:21 server sm-msp-queue[1560]: q5R2e4uo028125: to=root, delay=00:13:41, xdelay=00:06:18, mailer=relay, pri=123690, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 07:09:01 server CRON[3986]: (root) CMD ([ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) -delete) Jun 27 07:12:39 server sm-msp-queue[1560]: q5R1R7Ue004056: to=root, ctladdr=root (0/0), delay=01:45:32, xdelay=00:06:18, mailer=relay, pri=482407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 07:18:57 server sm-msp-queue[1560]: q5QMk7S9009582: to=root, ctladdr=root (0/0), delay=04:32:50, xdelay=00:06:18, mailer=relay, pri=1202407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 07:20:02 server CRON[7760]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jun 27 07:26:22 server sm-msp-queue[7775]: q5R2e4uo028125: to=root, delay=00:33:42, xdelay=00:06:18, mailer=relay, pri=213690, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 07:27:01 server CRON[9887]: (root) CMD (cd / && run-parts --report /etc/cron.hourly) Jun 27 07:32:40 server sm-msp-queue[7775]: q5R1R7Ue004056: to=root, ctladdr=root (0/0), delay=02:05:33, xdelay=00:06:18, mailer=relay, pri=572407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 07:38:58 server sm-msp-queue[7775]: q5QMk7S9009582: to=root, ctladdr=root (0/0), delay=04:52:51, xdelay=00:06:18, mailer=relay, pri=1292407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 07:39:01 server CRON[13813]: (root) CMD ([ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth : root@server:~# df -h Filesystem Size Used Avail Use% Mounted on /dev/simfs 20G 2.3G 18G 12% / - Jun 26 16:22:41 server varnishd[1413]: Child (32425) died signal=3 Jun 26 16:22:41 server varnishd[1413]: child (21687) Started Jun 26 16:22:41 server varnishd[1413]: Child (21687) said Child starts Jun 26 16:22:41 server varnishd[1413]: Child (21687) said SMF.s0 mmap'ed 1073741824 bytes of 1073741824 Jun 26 16:34:28 server -- MARK -- Jun 26 16:54:29 server -- MARK -- Jun 26 17:14:29 server -- MARK -- Jun 26 17:34:29 server -- MARK -- Jun 26 17:54:29 server -- MARK -- Jun 26 18:14:29 server -- MARK -- Jun 26 18:34:29 server -- MARK -- Jun 26 18:54:29 server -- MARK -- Jun 26 19:14:29 server -- MARK -- Jun 26 19:34:29 server -- MARK -- Jun 26 19:54:29 server -- MARK -- Jun 26 20:14:29 server -- MARK -- Jun 26 20:34:29 server -- MARK -- Jun 26 20:48:12 server exiting on signal 15 Jun 26 20:51:58 server syslogd 1.5.0#6ubuntu1: restart. Jun 26 20:52:01 server varnishd[1324]: Platform: Linux,2.6.18-308.el5.028stab099.3,i686,-sfile,-smalloc,-hcritbit Jun 26 21:11:58 server -- MARK -- Jun 26 21:31:58 server -- MARK -- Jun 26 21:51:58 server -- MARK -- Jun 26 22:11:58 server -- MARK -- Jun 26 22:31:58 server -- MARK -- Jun 26 22:51:58 server -- MARK -- Jun 26 23:11:58 server -- MARK -- Jun 26 23:31:58 server -- MARK -- Jun 26 23:51:58 server -- MARK -- Jun 27 00:11:58 server -- MARK -- Jun 27 00:23:42 server exiting on signal 15 Jun 27 02:21:10 server syslogd 1.5.0#6ubuntu1: restart. Jun 27 02:21:12 server varnishd[1341]: Platform: Linux,2.6.18-308.el5.028stab099.3,i686,-sfile,-smalloc,-hcritbit Jun 27 02:41:10 server -- MARK -- Jun 27 02:46:41 server syslogd 1.5.0#6ubuntu1: restart. Jun 27 03:20:44 server syslogd 1.5.0#6ubuntu1: restart. Jun 27 03:20:46 server varnishd[1238]: Platform: Linux,2.6.18-308.el5.028stab099.3,i686,-sfile,-smalloc,-hcritbit Jun 27 03:20:46 server varnishd[1238]: child (1239) Started Jun 27 03:20:46 server varnishd[1238]: Child (1239) said Child starts Jun 27 03:20:46 server varnishd[1238]: Child (1239) said SMF.s0 mmap'ed 1073741824 bytes of 1073741824 Jun 27 03:32:52 server exiting on signal 15 Jun 27 03:33:16 server syslogd 1.5.0#6ubuntu1: restart. Jun 27 03:33:31 server varnishd[1372]: Platform: Linux,2.6.18-308.el5.028stab099.3,i686,-sfile,-smalloc,-hcritbit Jun 27 03:53:16 server -- MARK -- Jun 27 04:13:16 server -- MARK -- Jun 27 04:33:16 server -- MARK -- Jun 27 04:53:16 server -- MARK -- Jun 27 05:13:16 server -- MARK -- Jun 27 05:27:42 server syslogd 1.5.0#6ubuntu1: restart. Jun 27 05:53:17 server -- MARK -- Jun 27 06:13:17 server -- MARK -- Jun 27 06:33:17 server -- MARK -- Jun 27 06:53:17 server -- MARK -- Jun 27 07:13:17 server -- MARK -- Jun 27 07:33:17 server -- MARK -- Jun 27 07:53:17 server -- MARK -- Jun 27 08:13:17 server -- MARK -- Jun 27 08:33:17 server -- MARK -- Jun 27 08:53:17 server -- MARK -- Jun 27 09:13:17 server -- MARK -- Jun 27 09:33:17 server -- MARK -- Jun 27 09:53:17 server -- MARK -- Jun 27 10:13:17 server -- MARK -- Jun 27 10:33:17 server -- MARK -- Jun 27 10:53:17 server -- MARK -- Jun 27 11:13:17 server -- MARK -- Jun 27 11:33:17 server -- MARK -- Jun 27 11:53:18 server -- MARK -- Jun 27 12:13:18 server -- MARK -- Jun 27 12:33:18 server -- MARK -- Jun 27 12:53:18 server -- MARK -- Jun 27 13:13:18 server -- MARK -- Jun 27 13:33:18 server -- MARK -- Jun 27 13:53:18 server -- MARK -- Jun 27 14:13:18 server -- MARK -- Jun 27 14:33:18 server -- MARK -- Jun 27 14:53:18 server -- MARK -- -- root@server:~# cat /var/log/nginx/error.log 2012/06/27 03:32:54 [alert] 1199#0: worker process 1203 exited on signal 9 2012/06/27 03:32:54 [alert] 1199#0: worker process 1200 exited on signal 9 2012/06/27 03:32:54 [alert] 1199#0: worker process 1201 exited on signal 9 2012/06/27 03:32:54 [alert] 1199#0: worker process 1202 exited on signal 9 root@server:~# cat /var/log/nginx/access.log 31.210.99.87 - - [27/Jun/2012:09:09:08 +0400] "GET /w00tw00t.at.ISC.SANS.DFind:) HTTP/1.1" 400 172 "-" "-" 88.191.138.103 - - [27/Jun/2012:13:27:08 +0400] "GET /cms/cmx.jsp HTTP/1.1" 301 184 "-" "-" 88.191.138.103 - - [27/Jun/2012:13:27:08 +0400] "GET /iesvc/iesvc.jsp HTTP/1.1" 301 184 "-" "-" 88.191.138.103 - - [27/Jun/2012:13:27:08 +0400] "GET /cmd2/index.jsp HTTP/1.1" 301 184 "-" "-" 88.191.138.103 - - [27/Jun/2012:13:27:09 +0400] "GET /cmd/index.jsp HTTP/1.1" 301 184 "-" "-" 58.97.147.197 - - [27/Jun/2012:17:17:19 +0400] "GET / HTTP/1.1" 301 184 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_7_4) AppleWebKit/536.5 (KHTML, like Gecko) Chrome/19.0.1084.56 Safari/536.5" 58.97.147.197 - - [27/Jun/2012:17:17:37 +0400] "GET / HTTP/1.1" 301 184 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_7_4) AppleWebKit/536.5 (KHTML, like Gecko) Chrome/19.0.1084.56 Safari/536.5" 58.97.147.197 - - [27/Jun/2012:17:17:38 +0400] "-" 400 0 "-" "-" 58.97.147.197 - - [27/Jun/2012:17:17:38 +0400] "-" 400 0 "-" "-" 58.97.147.197 - - [27/Jun/2012:17:17:48 +0400] "-" 400 0 "-" "-" - root@server:~# cat /var/log/daemon.log Jun 26 20:48:10 server xinetd[1177]: Exiting... Jun 26 20:51:58 server xinetd[1174]: Reading included configuration file: /etc/xinetd.d/daytime [file=/etc/xinetd.d/daytime] [line=28] Jun 26 20:51:58 server xinetd[1174]: Reading included configuration file: /etc/xinetd.d/discard [file=/etc/xinetd.d/discard] [line=26] Jun 26 20:51:58 server xinetd[1174]: Reading included configuration file: /etc/xinetd.d/echo [file=/etc/xinetd.d/echo] [line=25] Jun 26 20:51:58 server xinetd[1174]: Reading included configuration file: /etc/xinetd.d/time [file=/etc/xinetd.d/time] [line=26] Jun 26 20:51:58 server xinetd[1174]: removing chargen Jun 26 20:51:58 server xinetd[1174]: removing chargen Jun 26 20:51:58 server xinetd[1174]: removing daytime Jun 26 20:51:58 server xinetd[1174]: removing daytime Jun 26 20:51:58 server xinetd[1174]: removing discard Jun 26 20:51:58 server xinetd[1174]: removing discard Jun 26 20:51:58 server xinetd[1174]: removing echo Jun 26 20:51:58 server xinetd[1174]: removing echo Jun 26 20:51:58 server xinetd[1174]: removing time Jun 26 20:51:58 server xinetd[1174]: removing time Jun 26 20:51:58 server xinetd[1174]: xinetd Version 2.3.14 started with libwrap loadavg options compiled in. Jun 26 20:51:58 server xinetd[1174]: Started working: 0 available services Jun 26 20:52:01 server vnstatd[1330]: vnStat daemon 1.11 started. Jun 26 20:52:01 server vnstatd[1330]: Monitoring: venet0 Jun 27 00:23:41 server xinetd[1174]: Exiting... Jun 27 02:21:12 server vnstatd[1349]: vnStat daemon 1.11 started. Jun 27 02:21:12 server vnstatd[1349]: Monitoring: venet0 Jun 27 03:20:44 server xinetd[1166]: attribute: disable should not be in default section [file=/etc/xinetd.conf] [line=12] Jun 27 03:20:44 server xinetd[1166]: Reading included configuration file: /etc/xinetd.d/chargen [file=/etc/xinetd.conf] [line=15] Jun 27 03:20:44 server xinetd[1166]: Reading included configuration file: /etc/xinetd.d/daytime [file=/etc/xinetd.d/daytime] [line=28] Jun 27 03:20:44 server xinetd[1166]: Reading included configuration file: /etc/xinetd.d/discard [file=/etc/xinetd.d/discard] [line=26] Jun 27 03:20:44 server xinetd[1166]: Reading included configuration file: /etc/xinetd.d/echo [file=/etc/xinetd.d/echo] [line=25] Jun 27 03:20:44 server xinetd[1166]: Reading included configuration file: /etc/xinetd.d/time [file=/etc/xinetd.d/time] [line=26] Jun 27 03:20:44 server xinetd[1166]: removing chargen Jun 27 03:20:44 server xinetd[1166]: removing chargen Jun 27 03:20:44 server xinetd[1166]: removing daytime Jun 27 03:20:44 server xinetd[1166]: removing daytime Jun 27 03:20:44 server xinetd[1166]: removing discard Jun 27 03:20:44 server xinetd[1166]: removing discard Jun 27 03:20:44 server xinetd[1166]: removing echo Jun 27 03:20:44 server xinetd[1166]: removing echo Jun 27 03:20:44 server xinetd[1166]: removing time Jun 27 03:20:44 server xinetd[1166]: removing time Jun 27 03:20:44 server xinetd[1166]: xinetd Version 2.3.14 started with libwrap loadavg options compiled in. Jun 27 03:20:44 server xinetd[1166]: Started working: 0 available services Jun 27 03:20:46 server vnstatd[1249]: vnStat daemon 1.11 started. Jun 27 03:20:46 server vnstatd[1249]: Monitoring: venet0 Jun 27 03:32:41 server xinetd[1166]: Exiting... Jun 27 03:33:32 server vnstatd[1380]: vnStat daemon 1.11 started. Jun 27 03:33:32 server vnstatd[1380]: Monitoring: venet0 root@server:~# - Anything else you need let me know

  Read the article

• HTTP response time profiling

  - by Sparsh Gupta

  Hello I have a nginx reverse proxy. The server is close to serving 600-700 requests per second. I have a Munin HTTP load time plugin which is outputting this: http://monitor.wingify.com/munin/visualwebsiteoptimizer.com/lb1.visualwebsiteoptimizer.com-http_loadtime.html Now, the problem is I am seeing some spikes in the graph. Expected response times should always be under 200ms. I am keeping an eye on syslog and messages but I am unable to figure out the actual cause of this. I was wondering if there is any good HTTP response time profiling system which I can install / embed with this nginx server and get a detailed reports / logs on the breakup of time taken by different things and what exactly is the cause of the spikes. The profiling system would also help me understand bottlenecks and how can I further optimize the latency. Most important right now is to investigate the cause of the spikes in the HTTP load time graphs (similar pattern is reported by external monitors - Pingdom) and to fix it to get consistent response times Thanks

  Read the article

• Cannot start serial over lan on iDrac6

  - by Bryan Agee

  I have a couple of Dell R610/R710 servers loaded with iDrac6 system management boards. I figured out how to log into the SM CLP with ssh. According to the dell documentation, I should be able to start a console session by running: start /system1/sol1 but I get the following failure message: cmdstat status : 3 status_tag : COMMAND EXECUTION FAILED job job_id : 12 joberr errtype : 1 errtype_desc : Other cimstat : 6 cimstat_desc : CIM_ERR_NOT_FOUND severity : 2 severity_desc : Low /system1/sol1 started FAILED at Sun Sep 16 00:20:58 2012 I have enabled the serial-over-lan via the web interface and rebooted, but nothing seems to make them available.

  Read the article

• SharePoint webpart for WebEx

  - by Kelly French

  Is there a SharePoint webpart available for WebEx? We do a lot of web conferencing and want the functionality to be exposed through SharePoint but WebEx hasn't released a webpart yet. The solution provided by WebEx has its critics. I searched for 'SharePoint' in Cisco's WebEx knowledgebase and got back zero (0) results. Has anyone found either a workaround or maybe a third-party webpart?

  Read the article

• backup exec - backup to disk offline

  - by Adam

  Hi We are running backup exec 9.1 doing a backup to disk to portable hard disk drives. When we run the backup manually it works fine. But when the backup is setup to run in the evening on a schedule it does not run as the backup to disk folders goes offline and therefore has to be switched back on line. After we have done this the backup runs and completes fine. Any ideas? We have tried leaving the progam open and this makes no difference. Server is Windows 2003 SBS

  Read the article

• Pain removing a perl rootkit

  - by paul.ago

  So, we host a geoservice webserver thing at the office. Someone apparently broke into this box (probably via ftp or ssh), and put some kind of irc-managed rootkit thing. Now I'm trying to clean the whole thing up, I found the process pid who tries to connect via irc, but i can't figure out who's the invoking process (already looked with ps, pstree, lsof) The process is a perl script owned by www user, but ps aux |grep displays a fake file path on the last column. Is there another way to trace that pid and catch the invoker? Forgot to mention: the kernel is 2.6.23, which is exploitable to become root, but I can't touch this machine too much, so I can't upgrade the kernel EDIT: lsof might help: lsof -p 9481 COMMAND PID USER FD TYPE DEVICE SIZE NODE NAMEss perl 9481 www cwd DIR 8,2 608 2 /ss perl 9481 www rtd DIR 8,2 608 2 /ss perl 9481 www txt REG 8,2 1168928 38385 /usr/bin/perl5.8.8ss perl 9481 www mem REG 8,2 135348 23286 /lib64/ld-2.5.soss perl 9481 www mem REG 8,2 103711 23295 /lib64/libnsl-2.5.soss perl 9481 www mem REG 8,2 19112 23292 /lib64/libdl-2.5.soss perl 9481 www mem REG 8,2 586243 23293 /lib64/libm-2.5.soss perl 9481 www mem REG 8,2 27041 23291 /lib64/libcrypt-2.5.soss perl 9481 www mem REG 8,2 14262 23307 /lib64/libutil-2.5.soss perl 9481 www mem REG 8,2 128642 23303 /lib64/libpthread-2.5.soss perl 9481 www mem REG 8,2 1602809 23289 /lib64/libc-2.5.soss perl 9481 www mem REG 8,2 19256 38662 /usr/lib64/perl5/5.8.8/x86_64-linux-threa d-multi/auto/IO/IO.soss perl 9481 www mem REG 8,2 21328 38877 /usr/lib64/perl5/5.8.8/x86_64-linux-threa d-multi/auto/Socket/Socket.soss perl 9481 www mem REG 8,2 52512 23298 /lib64/libnss_files-2.5.soss perl 9481 www 0r FIFO 0,5 1068892 pipess perl 9481 www 1w FIFO 0,5 1071920 pipess perl 9481 www 2w FIFO 0,5 1068894 pipess perl 9481 www 3u IPv4 130646198 TCP 192.168.90.7:60321-www.**.net:ircd (SYN_SENT)

  Read the article

• least privilege account for WinRM remote calls on Windows 2008 Server

  - by aldrin

  ServerFault Windows experts: please consider the following use case: I have 2 Windows 2008 Server SP2 boxes let’s call them – SOURCE, CLIENT. On SOURCE: I create a new user called 'normal'. Just a plain user - no special privileges. On CLIENT: I run the following from a command prompt winrm get wmi/root/cimv2/Win32_UTCTime -r:SOURCE -u:normal -p:NormalPassword I get an output containing WSManFault: Message = Access is denied. On CLIENT: I repeat step 3 with the administrator identity, i.e. winrm get wmi/root/cimv2/Win32_UTCTime -r:SOURCE -u:Administrator -p:AdminPassword I get the current UTC time at SOURCE. The question is, what are the least privileges I need to assign to the user 'normal' to ensure that Step 3 behaves like Step 5. In other words, what's the least privilege to enable WinRM access for a non-Admin account?

  Read the article

• iftop - how to generate text file with its output?

  - by mickula

  iftop is great tool to view almost live bandwidth usage distinguished by source-ip source-port destination-ip destination port. I'm using it to see which client's ip is using most bandwidth. Now I would like to store output somewhere. iftop uses ncurses so iftop > log.txt does not work as expected, result file is not readable. Is there any tool like this which can be used to pipe output to a text file? Thanks for your replies.

  Read the article

• Import PCF file in Windows 7 VPN connection

  - by Prashant

  I have got PCF file for VPN connection from my client to login into there network. I can able to us it with Cisco client without any problem, but I noticed there is option in Window 7 for connection to VPN natively and I'm could not able figure out how to import PCF file content to it. I really appreciate if any one can help with this...

  Read the article

• How to set ulimits in Solaris 10

  - by James Bradley

  I normally use pam_limits.so and /etc/security/limits.conf to set ulimits on filesize/cputime etc for the regular users logging in to my server running Ubuntu. Can anyone give the best way of doing similar with Solaris 10. I think it is done using /etc/system but have no idea what to add to the file or indeed if it is the correct file. I'm particularly interested in setting up ulimit -f without going down the .profile route.

  Read the article

• WmiPrvSE memory leak on Windows 2008 *R2*

  - by MichaelGG

  I've seen references on Windows 2008 to WmiPrvSE leaks, but nothing about Windows 2008 R2. We're running R2 on top of Hyper-V (2008). We are also running NSClient++ for monitoring from opsview. Over time, WmiPrvSE.exe starts to use a lot of memory, causing memory alert issues (less than 10% free). VM has 2GB, WmiPrvSE consumes up to 500-600MB before I kill it. Killing the process doesn't seem to have any negative effect; it starts up again and I haven't noticed any problems. But after a day or two, it's back in the same situation. Any ideas on what to do? Resource Monitor doesn't show any Disk or Network IO by WmiPrvSE.exe. Just slowly climbing private memory... Edited to add: We aren't running clustering, or Windows System Resource Manager. The only regular WMI user I can guess is NSClient++, but we don't seem to have this problem on other servers.

  Read the article

• Updating Windows DNS records from a remote windows DNS server

  - by Luckyboy

  Does anyone know if it is possible for a windows 2003 DNS server to update the records for a domain so that it contains all the records of a domain of of a remotely based DNS server? Im almost certain that doesn't quite explain the problem so I shall illustrate with an example: We have two offices, both are based about 100 miles apart. One deals with IT (Intranet development etc.) while the other is a call centre that uses the Intranet systems. Currently each office has its own DNS server, with the IT office's and call centre's DNS servers containing entries for intranet site. The difference is that the IT DNS server records point to the various servers that host the Intranet sites (e.g. intranetsite1 - 192.168.1.10, intranetsite2 - 192.168.1.11) while all of the entries in the call centre's DNS point to the IT office's DNS server (intranetsite1 - [it office ip address], intranetsite2 - [it office ip address]). Is there any way that the call centre's DNS server could automatically add all DNS records hosted by the IT office's DNS, translating the IP addresses to the IP address of the IT office?

  Read the article

• Zimbra vs. Kerio Connect

  - by rahum

  We've been a Kerio partner for years and have deployed much Kerio Connect. Now we're looking at beginning hosting groupware for our clients and are wrestling over the right backend. Kerio Connect is fantastic, but we have a couple gripes: Kerio is often weeks behind on releases to keep up with major Microsoft and Apple updates that break functionality or at least impede new Apple/Microsoft features in their desktop clients We've been worried that Kerio has a historical habit of corrupting Apple's Open Directory; we know this happened years ago, and have suspected it happening earlier this year There's always some one or two features that are buggy in Kerio, in every release. These usually aren't dealbreakers, just annoyances. Kerio does not have any kind of HA feature set How does Zimbra compare? What are your gripes? Thanks! noam

  Read the article

• Yum update not working on CentOS 6.2 minimal install

  - by Owen

  Note: This is my first question on the stack exchange network so please give mercy and provide guidance where needed. I have installed a CentOS 6.2 KVM guest and I am having problem getting yum to work. This is my first time working with CentOS so I feel that it's a setting somewhere that I am missing but cannot find using google. Here are my steps; Downloaded CentOS-6.2-x86_64-minimal.iso, booted, and went through default steps (only questions asked where keyboard, timezone, root password and use entire hdd) Restarted, logged in, pinged google.com to no avail Set the following settings; vi /etc/resolv.conf nameserver 8.8.8.8 nameserver 8.8.4.4 vi /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE="eth0" HWADDR="52:54:00:42:1B:4A" #NM_CONTROLLED="yes" BOOTPROTO=none ONBOOT="yes" NETMASK=255.255.255.0 IPADDR=192.168.122.151 TYPE=Ethernet vi /etc/sysconfig/network NETWORKING=yes NETWORKING_IPV6=no HOSTNAME=server3.example.com GATEWAY=192.168.122.1 I can now ping google.com ping google.com PING google.com (173.194.70.139) 56(84) bytes of data. 64 bytes from fa-in-f139.1e100.net (173.194.70.139): icmp_seq=1 ttl=50 time=5.88 ms 64 bytes from fa-in-f139.1e100.net (173.194.70.139): icmp_seq=2 ttl=50 time=5.77 ms But I cannot 'yum update' yum update Loaded plugins: fastestmirror, presto Loading mirror speeds from cached hostfile Could not retrieve mirrorlist http://mirrorlist.centos.org/?release=6&arch=x86_64&repo=os error was 14: PYCURL ERROR 7 - "Failed to connect to 2a01:c0:2:4:216:3eff:fe0d:266d: Network is unreachable" Error: Cannot find a valid baseurl for repo: base My KVM guest is also NAT'd incase it's of concern.

  Read the article

• Are VMWare ESXi 5 patches cumulative?

  - by ewwhite

  It seems basic, but there's confusion about the patching strategy needed to manually update standalone VMWare ESXi hosts. The VMWare vSphere blog attempts to explain this, but it's still not clear. From the blog: Say Patch01 includes updates for the following VIBs: "esxi-base", "driver10" and "driver 44". And then later Patch02 comes out with updates to "esxi-base", "driver20" and "driver 44". P2 is cumulative in that the "esxi-base" and "driver44" VIBs will include the updates in Patch01. However, it's important to note that Patch02 not include the "driver 10" VIB as that module was not updated. Many of my ESXi installations are standalone and do not make use of Update Manager. It is possible to update an individual host using the patches make available through the VMWare patch download portal. The process is quite simple, and that part makes sense. The bigger issue is determining what to actually download and install. In my case, I have a good number of HP-specific ESXi builds that incorporate sensors and management for HP ProLiant hardware. Let's say that those servers start at ESXi build #474610 from 9/2011. Looking at the patch portal screenshot below, there is a patch for ESXi update01, build #623860. There are also patches for builds #653509 and #702118. Coming from the old version of ESXi, what is the proper approach to bring the system fully up-to-date? Which patches are cumulative and which need to be applied sequentially? Perhaps the download size is the confusing factor, but is installing the newest build the right approach, or do I need to step back and patch incrementally?

  Read the article

• LiteSpeed enable Access-Control-Allow-Origin (no response header on CORS request)

  - by Joe Coder Guy

  Seriously, I can't find a single page discussing this for litespeed. Using this format in the htaccess "Header set Access-Control-Allow-Origin http://aSite.com" (and https) sends the setting in the http response header, but I still get the "XMLHttpRequest cannot load https://aSite.com/aFile.php. Origin aSite.com is not allowed by Access-Control-Allow-Origin" error when trying to access https from http origin. Also, I receive no response header for https, only that message shows up in Chrome. Is the server still blocking it even though I've sent the proper headers? I read elsewhere that it helps to add these terms Access-Control-Allow-Headers X-Requested-With Access-Control-Allow-Methods OPTIONS, GET, POST Access-Control-Allow-Headers Content-Type, Depth, User-Agent, X-File-Size, X-Requested-With, If-Modified-Since, X-File-Name, Cache-Control but I don't see these in my headers. Using these, my PHP files aren't even reached (because they register no errors or anything), so it looks like it comes from the server only, but what do I know. Thanks in advance! Update Since no response header, Prashant seems to suggest it's a server issue in his error since it worked on another server. http://stackoverflow.com/questions/11953132/no-response-obtained-while-implementing-cors Anyone know how to flip this switch? Headers work now Bad litespeed format. Should look like this. Still being denied though. Header set Access-Control-Allow-Headers X-Requested-With Header set Access-Control-Allow-Methods OPTIONS Header set Access-Control-Allow-Methods GET Header set Access-Control-Allow-Methods POST Header set Access-Control-Allow-Headers Content-Type Header set Access-Control-Allow-Headers Depth Header set Access-Control-Allow-Headers User-Agent Header set Access-Control-Allow-Headers X-File-Size Header set Access-Control-Allow-Headers X-Requested-With Header set Access-Control-Allow-Headers If-Modified-Since Header set Access-Control-Allow-Headers X-File-Name Header set Access-Control-Allow-Headers Cache-Control

  Read the article

• Windows 2008, IIS7 and virtual directories

  - by Thomas

  I created a virtual directory called test (C:\test) under the Default Web Site and added two simple test files (one html and one aspx). I thought I had to add the IUSR and NetworkService (for application pools) to C:\test and grant the users appropriate rights in order for IIS7 to serve the content. It appears that is not the case at all as I can view any files in the virtual directory (even if I convert it to an application) without changing or adding any security settings on the C:\test folder. I just installed IIS7 with ASP.NET on Windows 2008 without changing any settings besides adding the virtual directory. Am I missing something? Even my book on IIS7 states that the user accounts should be added an appropriate rights should be added. I added the following to answer the comments: I am referencing the file using a public IP http://xxx.xxx.xxx.xxx/test/one.html and the IP nor localhost is in my trusted sites. I am not signed in on the server at all as I am accessing the content from my home machine and the content is on my production server. The following users/groups have access to c:\test on the server (Creator Owner, System, Administrators, Users) and the app pool is running under the default NetworkService account. I basically installed win2008, added the IIS role with asp.net. I then opened IIS7, added a virtual directory and copied two files to the directory to test. It works which is great but I want to understand why it works. How is it that IIS7 can access files in the C:\test folder without any permissions set.

  Read the article

• Nagios Creating lots of zombie process

  - by pradeepchhetri

  In my monitoring box, I have lots of zombie process created by nagios and they gets remove quickly also. I am using active checks to perform monitoring of my servers. I accumulated the defunct processes created using the following command: $ top -d 0.25 -b -n 20 > topout.txt This collected the output of top with 0.25s delay 20 times. I did grep on the topout.txt for the defunct process. $ cat topout.txt | grep defunct I get the following output. 8957 nagios 20 0 0 0 0 Z 6.0 0.0 0:00.02 nagios <defunct> 8951 nagios 20 0 0 0 0 Z 3.0 0.0 0:00.01 nagios <defunct> 8954 nagios 20 0 0 0 0 Z 3.0 0.0 0:00.01 nagios <defunct> 8945 nagios 20 0 0 0 0 Z 0.0 0.0 0:00.01 nagios <defunct> 8946 nagios 20 0 0 0 0 Z 0.0 0.0 0:00.01 nagios <defunct> 8980 nagios 20 0 0 0 0 Z 0.0 0.0 0:00.01 nagios <defunct> 9000 nagios 20 0 0 0 0 Z 0.0 0.0 0:00.00 nagios <defunct> 9024 nagios 20 0 0 0 0 Z 7.0 0.0 0:00.02 nagios <defunct> 9025 nagios 20 0 0 0 0 Z 3.5 0.0 0:00.01 nagios <defunct> 9040 nagios 20 0 0 0 0 Z 3.1 0.0 0:00.01 nagios <defunct> 9086 nagios 20 0 0 0 0 Z 0.0 0.0 0:00.01 nagios <defunct> 9087 nagios 20 0 0 0 0 Z 0.0 0.0 0:00.01 nagios <defunct> 9123 nagios 20 0 0 0 0 Z 6.1 0.0 0:00.02 nagios <defunct> 9126 nagios 20 0 0 0 0 Z 3.0 0.0 0:00.01 nagios <defunct> 9131 nagios 20 0 0 0 0 Z 3.0 0.0 0:00.01 nagios <defunct> 9091 nagios 20 0 0 0 0 Z 0.0 0.0 0:00.05 nagios <defunct> 9111 nagios 20 0 0 0 0 Z 0.0 0.0 0:00.01 nagios <defunct> 9119 nagios 20 0 0 0 0 Z 0.0 0.0 0:00.01 nagios <defunct> 9118 nagios 20 0 0 0 0 Z 0.0 0.0 0:00.01 nagios <defunct> 9151 nagios 20 0 0 0 0 Z 2.9 0.0 0:00.02 nagios <defunct> 9153 nagios 20 0 0 0 0 Z 2.9 0.0 0:00.02 nagios <defunct> 9150 nagios 20 0 0 0 0 Z 0.0 0.0 0:00.01 nagios <defunct> 9164 nagios 20 0 0 0 0 Z 3.5 0.0 0:00.02 nagios <defunct> 9171 nagios 20 0 0 0 0 Z 3.5 0.0 0:00.02 nagios <defunct> 9154 nagios 20 0 0 0 0 Z 0.0 0.0 0:00.01 nagios <defunct> 9156 nagios 20 0 0 0 0 Z 0.0 0.0 0:00.01 nagios <defunct> 9163 nagios 20 0 0 0 0 Z 0.0 0.0 0:00.01 nagios <defunct> 9167 nagios 20 0 0 0 0 Z 0.0 0.0 0:00.01 nagios <defunct> 9178 nagios 20 0 0 0 0 Z 3.8 0.0 0:00.02 nagios <defunct> 9174 nagios 20 0 0 0 0 Z 0.0 0.0 0:00.01 nagios <defunct> 9179 nagios 20 0 0 0 0 Z 0.0 0.0 0:00.01 nagios <defunct> 9182 nagios 20 0 0 0 0 Z 0.0 0.0 0:00.01 nagios <defunct> Can somebody help me in finding out the reason of these zombie processes and how i can prevent these zombie processes ?

  Read the article

• Should I enable "Intel NIC DMA Channels"?

  - by javapowered

  I have HP DL360p Gen8 646902-xx1 I'm trying to optimize my config for low latency trading. Should I enable "Intel NIC DMA Channels"? Will that help/affect my system? From HP doc: Added a new ROM Based Setup Utility (RBSU) Advanced Performance Option menu that allows the user to enable Intel NIC DMA Channels (IOAT). This option is disabled by default. When enabled, certain networking devices may see an improvement in performance by utilizing Intel's DMA engine to offload network activity. Please consult documentation from the network adapter to determine if this feature is supported.

  Read the article

• Should I switch my server to Ubuntu Server from Windows Server 2003

  - by user22162

  I have a server thats primarily used for SRCDS, I host a few Team Fortress 2 servers on it and I would much prefer a ssh-like (more so the no-gui part) for something like this, mostly because I can't navigate with my phone on VNC very well and also because there really is no need for a gui in this situation. I sort of want to make the switch but I am unsure, because my server 2003 is very fast and If I do need to reboot, it can reboot in under 30 seconds to desktop. Should I switch?

  Read the article

• Using unixODBC to connect to Oracle server

  - by Paul

  I am trying to configure our web server (RHEL 5.4 x86) to connect to an Oracle database using unixODBC. I have installed unixODBC-2.2.11-7.1.1, which yum tells me is the latest version. I have also installed the Oracle InstantClient 11.2 and the Oracle InstantClient ODBC library. I have symlinked the all the .so files in /usr/lib/oracle/11.2/client/lib to /usr/lib. I have set $LD_LIBRARY_PATH to /usr/lib/, $ORACLE_HOME to /usr/lib/oracle and $TNS_ADMIN to the directory containing my (valid) Tnsnames.ora file. Here are the contents of my /etc/odbcinst.ini file: [Oracle] Description = Oracle ODBC Connection Driver = /usr/lib/libsqora.so.11.1 Setup = FileUsage = and my /etc/odbc.ini file: [Oracle] Application Attributes = T Attributes = W BatchAutocommitMode = IfAllSuccessful CloseCursor = F DisableDPM = F DisableMTS = T Driver = Oracle EXECSchemaOpt = EXECSyntax = T Failover = T FailoverDelay = 10 FailoverRetryCount = 10 FetchBufferSize = 64000 ForceWCHAR = F Lobs = T Longs = T MetadataIdDefault = F QueryTimeout = T ResultSets = T ServerName = //<host>:<port>/<db> SQLGetData extensions = F Translation DLL = Translation Option = 0 UserID = (ServerName has been edited...host, port, and db are actually there, and correct) When I run isql I get $ isql -v Oracle isql: symbol lookup error: /usr/lib/libsqora.so.11.1: undefined symbol: SQLGetPrivateProfileStringW And running dltest gives me $ dltest Oracle SQLConnect [dltest] ERROR dlopen: Oracle: cannot open shared object file: No such file or directory If anyone has any insights I would be grateful, I've been trying to get this to connect for about 5 hours now... I am going home for the night, but will gladly provide more details, if necessary, tomorrow morning, to anyone willing to help...

  Read the article

< Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >