Search Results

Search found 3195 results on 128 pages for 'utility'.

Page 49/128 | < Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >

• Why won't USB 3.0 external hard drive run at USB 3.0 speeds?

  - by jgottula

  I recently purchased a PCI Express x1 USB 3.0 controller card (containing the NEC USB 3.0 controller) with the intent of using a USB 3.0 external hard drive with my Linux box. I installed the card in an empty PCIe slot on my motherboard, connected the card to a power cable, strung a USB 3.0 cable between one of the new ports and my external HDD, and connected the HDD to a wall socket for power. Booting the system, the drive works 100% as intended, with the one exception of throughput: rather than using SuperSpeed 4.8 Gbps connectivity, it seems to be falling back to High Speed 480 Mbps USB 2.0-style throughput. Disk Utility shows it as a 480 Mbps device, and running a couple Disk Utility and dd benchmarks confirms that the drive fails to exceed ~40 MB/s (the approximate limit of USB 2.0), despite it being an SSD capable of far more than that. When I connect my USB 3.0 HDD, dmesg shows this: [ 3923.280018] usb 3-2: new high speed USB device using ehci_hcd and address 6 where I would expect to find this: [ 3923.280018] usb 3-2: new SuperSpeed USB device using xhci_hcd and address 6 My system was running on kernel 2.6.35-25-generic at the time. Then, I stumbled upon this forum thread by an individual who found that a bug, which was present in kernels prior to 2.6.37-rc5, could be the culprit for this type of problem. Consequently, I installed the 2.6.37-generic mainline Ubuntu kernel to determine if the problem would go away. It didn't, so I tried 2.6.38-rc3-generic, and even the 2.6.38 nightly from 2010.02.01, to no avail. In short, I'm trying to determine why, with USB 3.0 support in the kernel, my USB 3.0 drive fails to run at full SuperSpeed throughput. See the comments under this question for additional details. Output that might be relevant to the problem (when booting from 2.6.38-rc3): Relevant lines from dmesg: [ 19.589491] xhci_hcd 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 19.589512] xhci_hcd 0000:03:00.0: setting latency timer to 64 [ 19.589516] xhci_hcd 0000:03:00.0: xHCI Host Controller [ 19.589623] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 12 [ 19.650492] xhci_hcd 0000:03:00.0: irq 17, io mem 0xf8100000 [ 19.650556] xhci_hcd 0000:03:00.0: irq 47 for MSI/MSI-X [ 19.650560] xhci_hcd 0000:03:00.0: irq 48 for MSI/MSI-X [ 19.650563] xhci_hcd 0000:03:00.0: irq 49 for MSI/MSI-X [ 19.653946] xHCI xhci_add_endpoint called for root hub [ 19.653948] xHCI xhci_check_bandwidth called for root hub Relevant section of sudo lspci -v: 03:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30) Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f8100000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] #18 Kernel driver in use: xhci_hcd Kernel modules: xhci-hcd Relevant section of sudo lsusb -v: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 3 bMaxPacketSize0 9 idVendor 0x1d6b Linux Foundation idProduct 0x0003 3.0 root hub bcdDevice 2.06 iManufacturer 3 Linux 2.6.38-020638rc3-generic xhci_hcd iProduct 2 xHCI Host Controller iSerial 1 0000:03:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection TT think time 8 FS bits bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Device Status: 0x0003 Self Powered Remote Wakeup Enabled Full, non-verbose lsusb: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 011 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 003: ID 04d9:0702 Holtek Semiconductor, Inc. Bus 009 Device 002: ID 046d:c068 Logitech, Inc. G500 Laser Mouse Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 006: ID 174c:5106 ASMedia Technology Inc. Bus 003 Device 004: ID 0bda:0151 Realtek Semiconductor Corp. Mass Storage Device (Multicard Reader) Bus 003 Device 002: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 006: ID 1687:0163 Kingmax Digital Inc. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 046d:081b Logitech, Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Full output: full dmesg full lspci full lsusb

  Read the article

• Internal HDs that don't contain the OS aren't accessable unless I try to manually browse them

  - by Hrafn

  So I have 4 internal hard drives, one that contains the OS (Ubuntu 12.04), all ext4. After starting the computer up, and without having tried to access the drives (File manager, terminal etc) it seems like the drives haven't been mounted. If I go into the "Disks" utility I see that the disks haven't been mounted. Programs that try to access the HD's during startup throw an error. For example my music player can't find the library, my note taking software can't find the database etc. But after opening the drive in a file manager everything works. I've checked SMART on all the disks and everything is a ok. Any and all ideas would be appreciated.

  Read the article

• How to set PcManFm as the default file manager?

  - by JarekJ83

  I think Nautilus is so slow, and I'd like to move to PCmanFM, but didn't find any good tips how to do this in Ubuntu 12.10. I have PCmanFM installed already, and I even changed: $ sudo gedit /usr/share/applications/nautilus-folder-handler.desktop [Desktop Entry] Name=Files Comment=Access and organize files Exec=pcmanfm %U Icon=system-file-manager Terminal=false NoDisplay=true Type=Application StartupNotify=true OnlyShowIn=GNOME;Unity; Categories=GNOME;GTK;Utility;Core; MimeType=inode/directory;application/x-gnome-saved-search; X-GNOME-Bugzilla-Bugzilla=GNOME X-GNOME-Bugzilla-Product=nautilus X-GNOME-Bugzilla-Component=general X-GNOME-Bugzilla-Version=3.2.1 X-Ubuntu-Gettext-Domain=nautilus Still slow Nautilus is default one.

  Read the article

• What software is responsible for connecting to the wireless net specified in /etc/network/interfaces?

  - by zuba

  I'm curious what software (package, utility in bin's) handle interface parameters in /etc/network/interfaces and decides to connect to the specified wireless net. I use wifi usb stick dlink DWL-110 attached to wlan0 with ndiswrapper driver. Sometimes wlan0 sees my wifi net - iwlist wlan0 scan shows it, but does not connect to it - iwconfig shows AP Not-Associated, until I replug the stick. Neither reinserting module with ndiswrapper, not ifdown/ifup or restarting networking helps. That is why I need to know what OS entity handles connection/reconnection to wireless net. EDIT: shame on me, I use wireless-tool package with wep encryption

  Read the article

• How do I disable/modify CPU underclocking due to temperature on a laptop with a 2nd generation core cpu?

  - by Tyson Marchuk

  I am running Ubuntu 11.04 on a tablet with a Core i5-2557M processor. When doing processing intensive tasks the CPU is forcibly under-clocked to 800MHz (instead of the normal base of 1.7GHz.) The CPU temperature is around 75 C. I have disabled CPU scaling (set governor to performance) but this seems to have no effect. I would like to either modify the behavior so that the throttling happens at 95 C or I would like to disable it altogether. Changing the min/max frequency as root using cpufreq works until the temperature rises and then it ceases to work, ignoring a minimum frequency above the 800MHz. On Windows 7 there is a 3rd party utility that can do this (ThrottleStop). Thank you.

  Read the article

• Recovering a deleted partition

  - by Kishore

  I had a dual boot PC running Ubuntu 12.04 and Windows 7. About a month back, I deleted the Ubuntu partition via the disk management utility (I do not remember whether or not I formatted the partition after performing this action). I ran into some grub issues and used lilo to solve the issue. I followed the simple instructions described in this blog post. I now realize that there were some files in the Ubuntu installation that I need. Of course, I backed up the data, but not this folder apparently. Is there any way to get the data back? I tried following the process suggested on another post on askubuntu (suggesting the use of TestDisk), but was not able to even install TestDisk. The live USB I use is running Ubuntu 12.04 and it does not have a synaptic package manager. Installing from the terminal does not work because even after I type: sudo apt-get update sudo apt-get upgrade the command: sudo apt-get install testdisk fails to work.

  Read the article

• How to safely back up the "Private" folder?

  - by ImaginaryRobots

  I have an ecryptfs "Private" folder in my home directory, and it is set up to automatically mount whenever I log in. I want to set up automatic backups to a network drive, but I don't want the contents of Private to be readable on the remote server. My understanding is that the Ubuntu "Backup" utility would run while I'm logged in, so it would see the folder contents without encryption. I'm backing up from a laptop, so it is essentially only on when I am logged in. I know that the Private folder is essentially a mounted filesystem, so it seems like I should be able to backup the encrypted image rather than the cleartext contents. What steps are needed to safely back it up, while maintaining the encryption? Note that I'm already familiar with the backup tools available, this question is about dealing with the ecryptfs folder safely.

  Read the article

• Will the Global Demand for Water Outstrip the Supply by 2030?

  - by Evelyn Neumayr

  A recent study conducted by the Economist Intelligence Unit and sponsored by Oracle Utilities, titled “Water for All?”,considers the preparedness of utilities to supply water to the current global population of over 7 billion people, with a further 1 billion expected by 2030. It compares strategies used by utilities in 10 major countries to address this challenge. This study’s findings show that wide-ranging water management efforts and large-scale investments must be made if utilities are to meet near-certain water stress—demand outstripping supply—by 2030. The report is based on an online survey of 244 executives of water utilities in these countries, supplemented by in-depth interviews with 20 water utility executives and independent experts. The research concludes that utilities worldwide expect to meet future demand, despite increased supply pressure on supplies, due to improvements in water productivity that the wide range of measures utilities and governments will take to ensure that water is used more efficiently. Read more about this here.

  Read the article

• Installing g++ on 8.04

  - by mathematician1975

  I am running Ubuntu 8.04 (currently I do not have the option to upgrade due to hardware problems). I need to get g++ onto my installation but as this is no longer supported I am unable to use the traditional apt-get approach. What are my options? Are ubuntu packages configured specifically for each version? For example could I manually download a later version of gcc and g++ that do not originally ship with 8.04 (say the 10.04 version for example) and build them from scratch? Do the compilers work in this way in the sense that they have a version PER ubuntu version or are they maintained as separate entities?? I do not know enough about ubuntu internals really and always use apt-get to obtain/update any packages I need. If it is possible to do it this way is there a way to be certain that I have everything I need with regards to utility packages needed by g++ for the installation??

  Read the article

• Microphone doesn't give any input, yet music does

  - by user52643

  I've tried a few guides but nothing works as of yet. I've tried two microphones, both of which work on my Vista setup but do nothing on Ubuntu. Nothing is on mute both on the Sound utility or Skype (which I'm trying to use my mic for). I've been informed that when my speakers are playing very load, this can be heard on the other end of a call, too. See link for cat /proc/asound/card0/codec#0 results which are apparently relevant... _' N.B. I am noob x

  Read the article

• E-Business Suite Applications Technology Group (ATG) Advisor Webcast Program – June 2014

  - by LuciaC-Oracle

  Webcast: EBS Patch Wizard Overview Date: Thursday June 12, 2014 at 18:00 UK / 10:00 PST / 11:00 MST / 13:00 EST Topics covered will include: What is Oracle EBS Patch Wizard Tool? Benefits of the Patch Wizard utility Patch Wizard Interface Patch Impact Analysis Details & Registration : Doc ID 1672371.1Direct registration link. Webcast: EBS Proactive Analyzers Overview Date: Thursday June 26, 2014 at 18:00 UK / 10:00 PST / 11:00 MST / 13:00 EST Topics covered will include: What are Oracle Support Analyzers? How to identify the Analyzers available? Short Analyzers Overview Patch Impact Analysis How to use an Analyzer? Details & Registration : Doc ID 1672363.1Direct registration link.If you have any questions about the schedules or if you have a suggestion for an Advisor Webcast to be planned in future, please send an E-Mail to Ruediger Ziegler.

  Read the article

• grub not detecting windows 8

  - by Satyajit B M

  I have a dell inspiron 5520. I had installed windows 8 and have ubuntu 12.04 installed in a different partition. I installed grub but it was not showing windows 8. So i added menuentry "Windows 8" { set root = "(hd0,4)" chainloader +1 } in /etc/grub.d/40_custom. Now i see windows 8 option but it says "error-invalid selection" when i select it. please help. This is the op of fdisk -l command /dev/sda1 * 16072 626807 305368 de Dell Utility /dev/sda3 7645184 500201471 246278144 7 HPFS/NTFS/exFAT /dev/sda4 500203518 976771071 238283777 f W95 Ext'd (LBA) Partition 4 does not start on physical sector boundary. /dev/sda5 500203520 870275071 185035776 7 HPFS/NTFS/exFAT /dev/sda6 870277120 886276095 7999488 82 Linux swap / Solaris /dev/sda7 886278144 976771071 45246464 83 Linux

  Read the article

• /etc/crypttab not working

  - by Jeremy Stein

  I used the Disk Utility to create an encrypted volume on an external drive. When I click the Unlock Volume button in that program, it mounts the drive for me. Now, I want to automate this process so that it will happen at boot-up. When I run sudo cryptsetup luksUUID /dev/sdb1, I get this: ca709269-1e3e-4e9e-9e08-7248f0e6c5a6 So, I create /etc/crypttab like this: backup_drive UUID=ca709269-1e3e-4e9e-9e08-7248f0e6c5a6 none And I added this line to /etc/fstab: /dev/mapper/backup_drive /mnt/backup ext3 default 0 2 When I reboot, Ubuntu tells me that the device is not available to map, so I tell it to skip it. It appears that the /etc/crypttab is not getting run correctly. How can I debug this?

  Read the article

• Not enough components to start the RAID array?

  - by urig

  I'm trying to retrieve data from a "Western Digital MyBook World Edition (white light)" NAS device. This is basically an embedded Linux box with a 1TB HDD in it formatted in ext3. It stopped booting one day for no apparent reason. I have extracted the HDD from the NAS device and installed it in a desktop machine running Ubuntu 10.10 in the hope of accessing the files on the drive. Unfortunately, Ubuntu has not been able to mount the drive automatically. Having started up Disk Utility I see the drive as a multi disk device called "Array (Array)" showing Metadata Version 0.90.0. The device state is: "Not Running, not enough components to start". When I click the "Start RAID Array" button I get an error saying: "Not enough components to start the RAID array". Can you please tell me which components are missing and how to install them to get access to the drive's filesystem?

  Read the article

• USB disk not recognized after detaching from DVD player. What to do?

  - by MMA

  I had one Transcend 4GB USB stick formatted to NTFS and was working fine. Today I inserted this disk into a DVD player, and it was saying, "loading". After a long time, noting happened, and it seemed that the stick (NTFS) is not recognized by it. I took out the stick and tried to reformat to FAT32. But the stick is not being recognized in my machine (Ubuntu 12.04). I tried the advices from USB drive not recognized after Erase Disk, without any success. When I tried Disk Utility, the stick is indicated as a generic device. See image, Formatting this device fails, saying, No medium found. Again see image, gparted does not even list this device. The same thing happens for fdisk. It is not listed there. Have I totally lost this stick? What should I do?

  Read the article

• Oracle Fusion Middleware 11g (11.1.1.3.0) ?????????

  - by Hiroyuki Yoshino

  ????Media Pack??????????????????????1, 2???????????????? ??????????????????????Oracle Fusion Middleware 11g (11.1.1.3.0)??????????????????????????FAQ????????????????????????????????? (?????????????????????????????) ????FAQ????????? Q. Oracle Fusion Middleware?????·????????????????? A. ??·??????????????????????·?????Oracle??????????????SOA Suite 11g R1 (11.1.1.2.0)???·??????? ?????????????????Oracle??????????????????????????????????SOA Suite 11g R1 (11.1.1.3.0)?SOA Suite 11g R1 (11.1.1.2.0)????????????????????????????? ??Oracle Technology Network???????·??????·???????????????????????????????? Q. ??????????????????????????????? A. ?????????????????????????????? Product Version Required Product WebLogic Server Repository Creation Utility JDeveloper 11.1.1.2 10.3.2 11.1.1.2.1 11.1.1.2.0 11.1.1.3 10.3.3 11.1.1.3.0 11.1.1.3.0 ????? ??????????????????????????

  Read the article

• Not detecting HDD after installing Ubuntu 12.04!

  - by Arthur

  After installing Ubuntu 12.04, which I'm using right now and it works great, my extra hard drive was detected the first time I turned on my computer but then it does not show anymore on my Home Folder, when I run the Disk Utility says that has a few errors but when I try to fix it, says that hard drive is busy and cannot do anything else. I've unmounted it and mounted again but nothing happens. Do you know what can be going on? Cause the first time that I was able to see my hard drive it had all the files I have, but I don't know if deleting the partition will format the whole hard drive or just the ubuntu files. THANKS in advance! BY THE WAY, I'm new to Ubuntu... :S

  Read the article

• windows system (bootloader) partition accidently deleted during multiple installs

  - by S.Y.T.

  After experimenting with multiple variations of backtrack and xbmcbuntu variations of Ubuntu with dual boot successfully, my windows partition became unrecognizable to grub. I used my windows boot CD to try to correct the problem. However, I deleted all partitions except for the NFTS one that contains my old windows install. (And, merged all other ones into that in hopes of getting back to the windows boot loader and out of grub) Now, all I get is a grub command prompt when I try and boot the system (how??? - I thought I deleted grub) And, now the windows boot disc doesn't even recognize the install. I've tried TRK to try and resolve the problem. Though I must admit ignorance in correctly using this utility. I've searched for other answers to this problem. Any help would be much appreciated. S.Y.

  Read the article

• Is there an application or method to log of data transfers?

  - by Gaurav_Java

  My friend asked me for some files that I let him take from my system. I did not see he doing that. Then I was left with a doubt: what extra files or data did he take from my system? I was thinking is here any application or method which shows what data is copied to which USB (if name available then shows name or otherwise device id) and what data is being copied to Ubuntu machine . It is some like history of USB and System data. I think this feature exists in KDE This will really useful in may ways. It provides real time and monitoring utility to monitor USB mass storage devices activities on any machine.

  Read the article

• External hard drive failing, is backup recovery possible?

  - by backitup

  I have a Seagate Freeagent external hard drive. While I was backing it up on Windows XP my pc crashed and I received the horrifying "Delayed Write Error" when I rebooted citing "$MFT" and a few other files. I tried to unmount it, but to no avail. Now my pc just crashes when I try to access it via Windows. In Ubuntu I am able to view it through disk utility. SMART status is "DISK FAILURE IMMINENT". Fdisk doesn't work, and the SMART tests fail on "Reallocated Sector Count". Is there any way for me to rescue any of my data. I can still access the drive but as soon as I do that it crashes.

  Read the article

• Error creating an .img file from an .ISO (MD5 verified)

  - by Rob

  I was following the instructions on this website to create a bootable USB flash drive on a Mac: http://www.ubuntu.com/download/help/create-a-usb-stick-on-mac-osx The instruction: hdiutil convert -format UDRW -o ~/path/to/target.img ~/path/to/ubuntu.iso does not create a valid file that the disk utility can copy to the USB drive, making installation on a USB drive useless. I've been repeating these instructions for days with no luck. The only thing that does not work is the .ISO to .IMG conversion. Is there a way to download Ubuntu 12.04 LTS 64-but Desktop in a .IMG file already? Unfortunately, my install notebook does not have an optical drive so USB is the only way. Thanks for your help!

  Read the article

• Usb boot device totally unable to be formatted

  - by fuqda

  I'm really upset by now, I've been trying 2hours straight to format a stupid usb drive (I'm new to ubuntu and I dont know if I will last long at this rate) Basically this was the lubuntu boot usb key I tried to remove files with sudo rm I tried to format disk with disk utility I tried to format disk with gparted (with unmounting beforehand) NOTHING WORKS. I cant delete a file. I cant move a file to the usb key. I cant do anything. This is really infuriating.. I dont know what to do ? here are some gparted errors while trying to format to fat32 after unmounting error fsyncing/closing/dev/sdb: input/output error input/output error during write on /dev/sdb when I try to remove by hand, it says "read-only file"

  Read the article

• Is it possible to boot without mounting /home?

  - by Exeleration-G

  I want to backup my /home partition on /dev/sda6 using partclone, a command line utility. To do so, I first have to unmount the partition that I want to backup. Most of the time, this is easy, but /home is used by so many processes that it can't be unmounted without first killing all those processes. So, the thing I'm looking for is a way to boot Ubuntu, without mounting /home, so I can back up the not-mounted /dev/sda6 partition. Is that possible? To be clear, it would be nice if this special boot could be 'one-time-only'. So I'm not looking for ways to change /etc/fstab in such way that /dev/sda6 won't be mounted. That's because that would require me to change /etc/fstab twice each time just to make a backup. I'm aware of the fact that there are other backup solutions available, such as deja-dup. I'd like to use partclone, though.

  Read the article

• USB Port not working for Ubuntu 14.04 LTS

  - by user292125

  I have recently installed Ubuntu 14.04 LTS on my system. But the usb port does not seem to be working. When I type lsusb in terminal, following is displayed on the screen: Bus 002 Device 114: ID 0951:1665 Kingston Technology Bus 002 Device 004: ID 413c:2106 Dell Computer Corp. Dell QuietKey Keyboard Bus 002 Device 003: ID 04ca:0062 Lite-On Technology Corp. Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub. However the disk utility shows no media. Kindly help me on this. Suggestions will be appreciated.

  Read the article

• Kernel Panic while Installing Ubuntu 12.10 from USB Drive

  - by user100889

  Good evening, I recently looked into installing Ubuntu alongside my Windows. I was able to mount the iso on a USB drive using Universal USB Installer. I verified it with the MD5sum utility and the hash is correct. When installing, I can get to the screen where I choose the boot order, select the USB drive, and then I get to a screen where Ubuntu seems to be 'loading' (purple background with Ubuntu logo and name in the middle). Then, all of a sudden, I get a "Kernel Panic - Not syncing: fatal exception in interrupt" error message. My specs : Intel Core 2 Duo CPU T5850 @ 2.16 GHz / 4 GB of ram / Packard Bell computer from 2007. / Windows 7 Ultimate x64 installed. What should I do now ? Thanks for your help.

  Read the article

< Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >