Search Results

Search found 17130 results on 686 pages for 'computer lab'.

Page 493/686 | < Previous Page | 489 490 491 492 493 494 495 496 497 498 499 500  | Next Page >

• Motherboard warning lights when plugging in a display port cord to graphics card?

  - by rllr

  Earlier today, my computer spontaneously shut itself off and refused to turn back on. I tested my PSU and it's operating fine. I unplugged everything and let it sit for a while and it started to make a high pitched coil whine/hiss. When I came back an hour later and plugged in only the power cord, it turned on without any issues. After some troubleshooting, I noticed my motherboard (Intel D975XBX2) has a red CPU led and VR led that come on whenever I plug my monitor into my graphics card via display port. DVI does not cause a similar issue. I was running three monitors off the card, so I need both DVI ports and the display port working. Is it likely my graphics card needs to be replaced, or should I be looking elsewhere to resolve this issue?

  Read the article

• Ubuntu sound volume is 40% lower than in Windows

  - by ncomx

  I have 2x 2.1 speakers connected to the computer where I have Ubuntu 12.04 installed. On the software side I've set all the volume controls to 100% with the alsamixer program. The speakers have their own volume control, maintaining those at the same level, and switching between Ubuntu and Windows (XP and 7), on windows the output volume is at least 40% higher, even when having the windows volume control at 50% (without touching the speakers volume control) it's still much higher than the sound on Ubuntu. Why can this be happening? Are there some alternative sound drivers (other than the default ones) I could test to see if it makes a difference? some info about the card: root:$ cat /proc/asound/cards 0 [PCH ]: HDA-Intel - HDA Intel PCH HDA Intel PCH at 0xfbff4000 irq 55 1 [Generic ]: HDA-Intel - HD-Audio Generic HD-Audio Generic at 0xfbcfc000 irq 56 root:$ lspci | grep -i audio 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 04) 02:00.1 Audio device: Advanced Micro Devices [AMD] nee ATI Cayman/Antilles HDMI Audio [Radeon HD 6900 Series] I think the one i am using is the Intel one, the other seems to be from the vga card which is an ati radeon 6950. Running gstreamer-properties and switching between alsa, oss, ossv4 and pulseaudio doesn't seem to make any difference.

  Read the article

• A software to lock regions of a screen to prevent any windows from overlapping

  - by cybervaldez

  I've just installed nexus dock (a similar application like rocketdock), after playing with the preferences i've come across a very curious option (under position & behavior) that says: Prevent maximized windows from overlapping the dock. With it enabled, any application I maximize(and i do mean any) won't overlap the dock, it's really great. So i'm thinking perhaps there's a software that does this kind of feature which is really ideal for keeping my workspace really organized. I really hate repositioning and resizing my windows everytime. Of course there's always the manual way of doing these but it's just too much of a bother when someone from the family uses the computer. Do you know any software that does this? even a software that can just save/remember window positions would also be nice too.

  Read the article

• Seeking a solution to automatically copy files from the cd-rom disk to the USB drive once it's connected.

  - by Ray Nathan

  I plan to distribute a free CD that automatically copies files to a connected usb device. This process will be done on the computers of the users that obtain the cd. The CD will contain an autorun.ini file that will instruct the computer to copy a set of files located on the cd..to a specific directory on the connected usb device. The usb drive letter is not the same on all the systems, therefore...Windows XP should automatically know the drive letter of the usb device before the copy operation begins. What would be the best way of creating a short batch file or script that I can place on the CD to execute this process? Also, please note that it is NOT feasible or recommended to include a batch file on the USB devices to sync this operation due to the explanation at the beginning of this paragraph. :) Thank You All

  Read the article

• How do you make slides for programming talks?

  - by Yuvi Masory

  I've given a few talks recently and I have not found a good way to make slides. Here are a few desirable characteristics for programming slides: They're slides. A standard emacs buffer won't do it. They have syntax highlighting for code. They support basic formatting, like font size and color and bullets. No fancy animations needed. The only animation I desire is one-by-one appearance of bullets. So far I have considered: Microsoft Office - out of the question for Linux users. OpenOffice.org - too much for my needs, code formatting/highlighting needs to be done externally and pasted in. On the plus side supports bullets, bullet-by-bullet animation, and font formatting. Emacs - Supports all the code formatting but I haven't found a slides mode that lets me transition from one chunk to another. HTML5 - I once made slides using html5rocks as a template. It supports everything, but is too hard and time-consuming the "throw together" a few slides before a minor talk. Also the html5-only features may not work on the podium computer's installed browser. Any suggestions for programs/techniques for making code-centric presentations?

  Read the article

• Update saved password for basic authentication using a script

  - by Kalamane

  I have a website that uses basic authentication as described on this webpage. Each of the computers I manage have the password saved in their browser. There is only one username and password for this. After someone logs in to the site this way, they are presented with their individual username and password prompt as part of the web page. The purpose of the initial username/password is to discourage non-technical employees that aren't supposed to be using the page from even viewing it. So far, when we've had to change this password, I've manually gone to each computer and updated the saved password. I'm writing a startup script to configure other aspects of these systems so that I can maintain them easier. I'd like to be able to update the saved password via this script. The operating system running on these machines is Windows XP SP3 and the browsers they're using to access this site are IE8 and IE9. How can I update the saved basic authentication information for a website via a script?

  Read the article

• Saving Photoshop workspace doesn't remember docked panel state

  - by johnh

  A friend of mine has recently setup his computer with a fresh install of Windows 7 and Photoshop CS5. He's having a strange issue with saved workspaces not remembering the state of docked panels. As an example, he's docked several panels on the right of the screen. The Layers panel is docked but is open, showing all layers in the document. If he saves this as a workspace, closes and reopens Photoshop and loads the workspace, the Layers panel is docked but is closed. It's not the only panel this is happening with. It's not a big problem but he's having to open 4 panels and drag them to the appropriate height each time he starts Photoshop. Does anyone know of a possible fix for this? Any insight would be great.

  Read the article

• Looking for a central image database and tagging system for a group of users

  - by jstarek

  I'm doing IT support for a small volunteer organisation who needs to centrally store and organize around 2500 photos. Can anyone here recommend a database or similar system which matches the following criteria: Intuitive to use for users with little computer experience Multi-user support, ideally with integration in our existing LDAP user directory Should have a web-interface Not a hosted solution like Picasa (because we have a rather slow internet connection with very slow upload) Should allow tagging of images, sorting by various criteria and storing copyright information If there are native GNOME and/or Windows clients for the tool, that would be a great benefit. Many thanks in advance!

  Read the article

• IPSec on Domain Controllers and Trusted Domains

  - by OneLogicalMyth

  I am looking at configuring IPSec as follows: Isolation Request authentication for inbound and outbound connections Computer and user (Kerberos V5) I am looking to do a blanket deployment across all servers and domain controllers. Workstations I will leave as not set. What impact in terms of the domain controllers with the 2-way forest trust do think I would see? Should I exclude the IP addresses of the trusted domain controllers? I don't want to stop communication between the current and trusted forest, however I do want IPsec to be used within the current forest on all servers. The trusted forest is running 2008 R2 and the current forest is 2012 R2.

  Read the article

• Apple TV photo fail

  - by Tony

  I just bought the new (2nd gen) Apple TV. Everything works beautifully, except for Photos. I have 25,000 pictures on my computer, which creates 3 issues with Apple TV 1) It takes roughly an HOUR to load my photos, every time! (if I navigate anywhere else, its has to reload all over again next time) 2) It condenses all of my folders-sub-folders-sub-sub-folders into just the top folder. Having only 5 top folders with 5,000 pictures each is pretty much useless. 3) It has an artificial cap of 20,000 pictures, after which it won’t load more. The first two are the big ones, since they pretty much make the product unusable. I have called apple support (they just said “sorry…too bad”), and have checked all the online forums I can. Also it is definitely not a connection issue, as it streams HD Netflix movies with ease. Does anyone else here have this issue, and/or hopefully some solutions?

  Read the article

• deploying skype for 50 nationwide users with preset usernames

  - by kevyn

  Is there a way to sign up a large group of skype names at once? is there a way to enable the users to be given a skype username based on their own e-mail addresses? What I would like to do is roll out skype in an office in every county in UK with a pre defined username such as 'mycompanyname-warwickshire', 'mycompanyname-bedfordshire' and so on. Our users are only basic computer users, so I would ideally like this done with as least fuss as possible for them! Thanks in advance ps. if anyone has a good way of doing this by using any alternative software, I'm open to suggestions

  Read the article

• print job doesn't go to print queue

  - by flatsguide

  I have two printers hooked up to my intel imac. I am having a printing error. It seems that whenever i try to print (a simple text doc) I am unable to get the print job to go to print queue with one of my printers. I have a HP c7280 and a HP c3100. I am able to get one working properly, but the other doesn't seem to allow it to go to the print queue. I have switched usb cables (with the printer that I know works) and both printers are recognized by the computer in the printer preferences pane. I've tried reseting the printer system in the printer setup utility.. reloaded the drivers from HP.. etc. If anyone has a suggestion or could point me to a little help i'd be VERY grateful Best Regards.. B

  Read the article

• how to troubleshoot shutdown problems in windows 7

  - by Ieyasu Sawada

  I have a desktop with windows 7 ultimate installed. Whenever I shut it down from the start button. The text that says that it is logging off and shutting down is present and the monitor blacks out and says no signal. But the lights in the RAM is still on and all the fans in the desktop is still spinning. Why is that? It seems like its not shutting down completely. I have also got disk problems lately. Event id 175 and 50. Which I think is caused by the computer not shutting down completely. How do I troubleshoot this one? Feel free to ask if you need more details, thanks.

  Read the article

• Removing partition to install OS?

  - by Shane

  So i have a computer that has 2 hard drives and i installed Ubuntu server on it. I used LVM to connect the two. So i tried to put windows back on it but it failed because it said it couldn't position the drive and then when i booted again the OS couldn't be found. So i booted it with the Ubuntu setup disc but now when it goes to partition it says that the position can not be modified because its already in use. I am asking if there is a way i can just remove everything and start fresh?

  Read the article

• Ubuntu update deleted entries from grub

  - by Kevin

  My computer currently has Fedora, Ubuntu, and Windows installed. I just updated Ubuntu 12.04, and on restarting, the Fedora entry was gone from GRUB. Ubuntu and Windows remained, though. I have looked at these threads: Fedora login gone after Ubuntu updates on a dual boot http://forums.fedoraforum.org/showthread.php?t=279221 GRUB's menu.lst deleted after a kernel update However, I cannot figure out how to mount the drive as suggested. It does not appear in the list on the left side of nautilus as shown in the links above. I also tried running the following as suggested above: sudo grub-install /dev/sdX sudo update-grub But this gave scary errors: /usr/sbin/grub-setup: warn: Attempting to install GRUB to a partitionless disk or to a partition. This is a BAD idea.. /usr/sbin/grub-setup: warn: Embedding is not possible. GRUB can only be installed in this setup by using blocklists. However, blocklists are UNRELIABLE and their use is discouraged.. /usr/sbin/grub-setup: error: will not proceed with blocklists. The highlighted drive below is where Fedora lives. Thanks for any help reversing Ubuntu's decision to delete this from GRUB.

  Read the article

• i accidentally deleted the recovery folder on a partition (win vista home)

  - by paul

  i accidentally deleted the recovery folder on the recovery partition (win vista home) i think it was some sort of scheduled maintenance of some program that i did not configure properly? oops... lol i called toshiba and they said i needed to buy a recovery program, which i didnt bother doing. I bought a legal copy of vista and would like to install the correct files and in a way that when my computer starts looking for files it will eventually find them or i can point to the partition. i'm pretty sure it's not a matter of copy and paste (is it?) thanks Paul

  Read the article

• Isopropyl okay to use on MacBook screen?

  - by Archagon

  I've always used a mixture of isopropyl alcohol and distilled water to clean my computer screens (50% water and 50% * 70% isopropyl). From what I understand, these are exactly the same ingredients used in most commercial screen cleaners, perhaps even more diluted. I recently used this solution to wipe off my 2010 MacBook Pro screen, and there don't seem to be any problems, but this support page explicitly says not to use isopropyl. Now I'm worried that I might have inadvertently damaged something. I'm also concerned because I once managed to dissolve the surface rubber lining of one of my mice with the isopropyl solution, and the MacBook Pro display has a thin rubber bezel keeping the glass in place. Why would Apple single out isopropyl on their support page? Should I be concerned?

  Read the article

• Does Wake-on-LAN from power state S5 require any OS configuration?

  - by TARehman

  I am configuring a HTPC which I would like to be able to power on using Wake-on-LAN, from the S5 state (full shutdown, still plugged in). The system is running Linux Mint 14 Cinnamon. I'm getting some conflicting information in my searching on the Net. I am not concerned with using WoL to change the state from standby or hibernate to on. Because of the current interface to our TV, the system must be either turned on or turned off. So, basically, this system will cycle from S0 to S5, and from S5 back to S0, and so on. Some tutorials suggest that I need to use ethtool to configure things after enabling WoL in my BIOS, but my understanding is that doing an S5 - S0 power on only requires the BIOS to be configured (since when the computer is in state S5, the OS hasn't even been loaded anyway). Can I use WoL with only the BIOS configured to go from state S5 to S0, or will I need to configure the OS as well?

  Read the article

• Two users using the same same user profile while not in a domain.

  - by Scott Chamberlain

  I have a windows server 2003 acting as a terminal server, this computer is not a member of any domain. We demo our product on the server by creating a user account. The person logs in uses the demo for a few weeks and when they are done we delete the user account. However every time we do this it creates a new folder in C:\Documents and Settings\. I know with domains you can have many users point at one profile and make it read only so all changes are dumped afterwords, but is there a way to do that when the machine is not on a domain? I would really like it if I didn't have to remote in and clean up the folders every time.

  Read the article

• Will I have internet connection issues next day, if I unplug router at night?

  - by headskracher77

  I did this regularly a few years ago and used to feel like I was 'being punished' by the Interent svc provider for disabling access to my computer, because trying to re-connect the next day became a constant pain. I have the same linksys router, a comcast modem, and hi-speed broadband through their LAN. Question: who or what is at fault for lousy internet connections, slow connections, or no connections: (everybody's tech dept. blames everybody else) The router? 10 year olds, maybe obsolete? The modem? came with the service plan - can connect three devices on a sharedconnection. The ISP: I read they not only even control and completely regulate bandwidth usage, but they also ration it!! (true?) So can I safely 'pull the plug' each night for security or not? thnx

  Read the article

• Installation causing broken packages

  - by AWE

  Here I come I am so determined to use Ubuntu that I paid a professional to install it for me (dualboot). When I got it I got a lot of things from the software center. Skype did not have a download button so I googled it and Ubuntu help told me to do this: sudo add-apt-repository "deb http://archive.canonical.com/ $(lsb_release -sc) partner" and then this: sudo apt-get update && sudo apt-get install skype The terminal told me "that this is potentially harmful..." but I thought it was Ubuntu language meaning "are you sure?" Now items cannot be installed or removed until the package catalog is repaired, so I want to repair it but the package operation fails. "sudo aptitude -f install" - command not found Synaptic package manager tells me that I have two broken packages, libc6 and libc6-dev but doesn't help, only makes life complicated. What the *#$%&!!! I don't want to be forced to become a computer scientist just to be able to use a free source os. P.s. the sound stopped working

  Read the article

• Where should I plug in my monitor -- Motherboard or Graphics card?

  - by Jeremy White

  Assuming I am using the following equipment... motherboard with HDMI/DVI & no embedded graphics discrete graphics card (nVidia or ATI) on PCI-E slot Intel CPU with integrated graphics ...where should I plug my monitor into the computer? Presumably, I'll get the fastest speed on games connected directly to the graphics card. But there is also power savings when connecting to the motherboard and accessing the Intel on-board graphics. I've read that some motherboards can switch automatically between the Intel graphics and discrete graphics. Is that something that works well, and where do I connect the monitor to enable that?

  Read the article

• Chipset GPU causes a massive slowdown

  - by zyboxenterprises

  My AMD Radeon HD 7700 recently broke (fan stopped working and GPU overheated), and now I'm running on internal chipset graphics, and it causes a massive slowdown of the whole PC. I've changed the graphics memory from 32MB (minimum) to 256MB (highest), and it hasn't made any difference whatsoever. I'm using Windows Aero, and disabling it should have made a small difference, but it didn't; the whole PC is still slow. I know that it's not the computer build, because I built it myself, and it was a lot faster when it had the AMD Radeon HD 7700 in it, which is the reason why I believe it's the internal chipset graphics that are causing the problem. Is this behavior normal? I don't have the cash right now to go out and buy a new dedicated GPU. I'm using an ASRock N68C-GS FX motherboard with an AMD FX 4100 (overclocked to 4.3GHZ), with 4GB RAM. The overclock was an attempt to resolve this issue, and it isn't related to this issue that the integrated graphics is causing a slowdown.

  Read the article

• laptop suddenly became very slow

  - by Ieyasu Sawada

  I have a compaq laptop. And I've been using it 2 years now. Then this day, it suddenly became very slow. It almost took 5 minutes from turning on to the log on screen. I click my username and it took 3 minutes to show the desktop. I click on my computer then properties to see if it is still showing 2 Ghz for the Core 2 duo processor. And 2gb for the memory. It took 10 minutes for all the information to show up. And its still 2gb and 2Ghz. So I may conclude that this is not a problem in memory or cpu. Its still running perfectly last night. And I have not seen signs of it failing. Things I already tried: Rebooting Shutdown then turn on again So how do I determine what causes this problem? How do I fix it?

  Read the article

• Windows 7 - Remote Desktop - multiple credentials

  - by w-

  Hi, My home network consists of a couple XP machines and a windows 7 box. One of the XP boxes is like a shared server accessed via Remote Desktop. I have an account on there and my gf has another. Previously I was able to save RDC shortcuts to this shared server including credentials. So in order to access the server from a computer on the network, i just needed to open the shortcut. I thus would have two shortcuts, one for my account and one for my gf's. In windows 7, it seems to store credentials for a box based on machine name. i.e. i can only store one set of credentials per machine name. This seems incredibly stupid so my question is: In windows 7, is there some way to have RDC shortcuts that use different credentials to login to the same target box? thanks

  Read the article

< Previous Page | 489 490 491 492 493 494 495 496 497 498 499 500  | Next Page >