Search Results

Search found 20569 results on 823 pages for 'pc settings'.

Page 495/823 | < Previous Page | 491 492 493 494 495 496 497 498 499 500 501 502  | Next Page >

• DNS Resolution doesn't work after uninstalling Cisco VPN & Deterministic Network Enhancer in Win 7

  - by Craig M

  I just upgraded my home PC to Windows 7 Ultimate 32 bit. After trying various methods to get the Cisco VPN client to work, I gave up and decided to just run it in XP mode. The last steps I tried were in this article ( http://social.technet.microsoft.com/Forums/en-US/w7itproappcompat/thread/d880dfe5-7f44-4955-8620-2a9355d8ea8b/ ) After that, I uninstalled the Cisco client and rebooted. I uninstalled the Deterministic Network Enhancer and rebooted again. Both uninstalled successfully, but now I'm not able to resolve any DNS. The only way I can resolve DNS is to reinstall the DNE, reboot, and uninstall the DNE. Then I am able to resolve DNS lookups until I reboot again. Once it's rebooted, no more DNS. Any ideas?

  Read the article

• Easy way to access cookies in Chrome

  - by macek

  To view specific cookies in Chrome, currently I have to: Go to preferences Click Under the Hood tab Click Content Settings... button Click Cookies tab (if it's not already active) Click Show cookies and other site data... button If I want to narrow this down to a specific domain, I have to type it in, too. Compare this to Firefox: View Page Info Click Security tab Click View Cookies The domain for the page I'm currently on is already used as a filter, too. My question: Is there an easier way in Chrome? I've done some searching for an extension but have come up with nothing. Any help is appreciated :)

  Read the article

• Why do I get "General Failure" when pinging host name on a Win 7 node on the network?

  - by hydroparadise

  This is a very peculiar problem with a station on our network. The client pc is running Windows 7 Pro. What makes this problem interesting is that this client is the only node on the network that seems to be experiencing this proglem. When I try to ping a specific Win 08 server by host name, I get an IPv6 address and get General failure. But when I ping it's IPv4 address, it responds just fine. My first thought would check the DNS server the name resolutions to see what would be going on, but the problem begs the quesion, why does the station get an IPv6 address back and fails as opposed to using the IPv4 settings (which are static btw). What gives? I am including a screen shot of trying the one specific server and failing while trying another server with success. All other nodes on the network don't have problems communicating with the server the one station is having issues with.

  Read the article

• IE and Chrome won't browse the internet on dial up but firefox will. How could I fix it?

  - by Kelbizzle

  First let me say I've done plenty of troubleshooting and will try to explain as clearly and as much as I can. Please bear with me. I have a client's computer who uses dial-up and Windows XP. The problem is when I connect to the dial up ISP. IE or Chrome will not browse the internet. It says page cannot be displayed. but if I use firefox on the dialup connection it works. Sounds simple enough there has got to be something wrong with the proxy settings or something...well, that's what I thought here is the weird part. When connected to the LAN in my office IE, Chrome, and FF all work. I upgraded to ie8 and the issue still happens. How would you go about troubleshooting this issue? What should I do next?

  Read the article

• No network adapter drivers after Windows re-install

  - by Arno

  This is a pretty basic question. I got a PC (Packard Bell Easynote TK11-BZ-010BE) that had linux on it, so I thought, just delete the partition and its alright. Well, it wasn't. I went into grub recovery and couldn't do anything, so I re-installed windows again. Now the problem is that everything works expect my network adapter. When I go to device manager, I get that there aren't any driver's for it installed. But without internet, I can't install the so called driver finders. How should I solve this?

  Read the article

• What is the lease irriating printer manufacturer?

  - by aireq

  Currently I have a Lexmark all in one printer/scanner which has some of the worse drivers I've seen for a printer. The installation takes forever. Then once it's installed the printer will only work if I keep the "Lexmark Productivity Studio" running in my system tray. Then later after I've scanned something 99% of the time the "Save to PDF" button doesn't do anything when I click it. It is also a wireless printer, but of course the only way to set any of the wireless settings is during the driver setup. So if my WEP key changes then I have to go off and reinstall the entire printer driver. Lately I tried refilling one of the ink cartridges with a key I bought off amazon, and now both the printer and the drivers keep complaining about being out of "Official Lexmark Ink" This comic from The Oatmeal pretty much sums up my feelings about consumer printers and their drivers. This question is, of course, pretty subjective but I'd like to know what (if any) consumer printer brands actual provide quality drivers and software with their printers.

  Read the article

• Puppet yum repo - Pull down 2.7.x vs 3.0.x

  - by Mike Purcell

  So a few weeks ago I started on the path to using puppet to automate all the configs/services. At the time I was using the EPEL repo, which installed version 2.6.x. After some reading I was trying to gain access to the flatten method available via the puppet stdlib, and thought it was available by default in the newer 2.7.x version. So I added a puppet repo with the following settings: [puppetlabs] name=Puppet Labs Packages baseurl=http://yum.puppetlabs.com/el/$releasever/products/$basearch/ enabled=1 gpgcheck=1 gpgkey=http://yum.puppetlabs.com/RPM-GPG-KEY-puppetlabs The problem with this, is it installed v3.0.x instead of 2.7.x. And apparently 3.0.x is a major upgrade which was released only a few weeks ago. Obviously I would prefer to use the 2.7.x for the next few months while PuppetLabs fix any defects which will inevitably arise after a major version. So my question is, what setting can I add to the puppet repo config to pull down only the 2.7.x branch and not the 3.0.x branch?

  Read the article

• Domino 8.5.3: Modify Subject of Incoming Email

  - by Void

  I am a newbie in managing and development for Domino. Recently, I have request from other teams at work to set up a filter or agent for incoming mail. This is the requirement for the request: Look for Incoming Mail addressed to #CRITICAL (mutlipurpose, internal group containing a list of engineers) For mail matching Point 1, append "For Immediate Action: " to the front of the Subject Some restrictions I have: Only the Domino server is under my charge, not to touch on network-side or other servers No 3rd party software to be installed I have gone through the configurations in the Domino server and the closest thing I have to filtering Email is the Router/SMTP Restrictions... Rules. But this is not able to fulfill Point 2 in any way. Is this even possible using just Domino server settings, or through agents?

  Read the article

• McAfee VirusScan Enterprise or avast! Free?

  - by Pieter

  I currently have McAfee VirusScan Enterprise on my computer. This was preinstalled on my PC. (My university did a bulk laptop purchase so I got a sweet deal on my laptop. McAfee was one of the extras that were included.) Apparently, it's getting bad ratings from sites such as Virus Bulletin and AV-Test. Am I better off with avast's free antivirus? Is it worth considering avast! Internet Security? I currently have a three-year license for VirusScan Enterprise. I keep my software up to date using Secunia PSI and I don't click on any suspicious links.

  Read the article

• Changing Word mail merge data source locations in bulk?

  - by Daft Viking

  I've just moved a number of Word mail merge files, and a number of Excel spreadsheets that are the data sources for the mail merges, from a Windows XP computer to a Windows 7 computer, and now all the paths for the merge sources are incorrect (used to be c:\documents and settings\user\my documents.... now c:\users\documents....). While I can correct the path of the data source in each file individually, I was hoping that there would be some way of updating the files in bulk, as there are a relatively large number of them. Word 2007 is what is being used, but the documents are all in the previous DOC format (not DOCX).

  Read the article

• Access is denied while moving a file from different volumes

  - by logeeks

  i have a portable 500GB HDD plugged into my dell xps system. The system have windows 7 professional edition. the problem is that when i try to open a file(visual studio .sln file) it is saying that access is denied. I cannot copy this file to a different location(within my local HDD) it is saying that i need permission for the task to complete. I've checked and confirmed the following things 1) I've logged into an admin account before attempting these operations 2) My admin account have 'Full Control' 3) I've full control over the portable HDD 4) I changed the 'UAC' settings to 'Never notify' Please help.

  Read the article

• Improving TCP performance over a gigabit network lots of connections and high traffic for storage and streaming services

  - by Linux Guy

  I have two servers, Both servers hardware Specification are Processor : Dual Processor RAM : over 128 G.B Hard disk : SSD Hard disk Outging Traffic bandwidth : 3 Gbps network cards speed : 10 Gbps Server A : for Encoding videos Server B : for storage videos andstream videos over web interface like youtube The inbound bandwidth between two servers is 10Gbps , the outbound bandwidth internet bandwidth is 500Mpbs Both servers using public ip addresses in public and private network Both servers transfer and connection on nginx port , and the server B used for streaming media , like youtube stream videos Both servers in same network , when i do ping from Server A to Server B i got high time latency above 1.0ms , the time range time=52.7 ms to time=215.7 ms - This is the output of iftop utility 353Mb 707Mb 1.04Gb 1.38Gb 1.73Gb mqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqq server.example.com => ip.address 6.36Mb 4.31Mb 1.66Mb <= 158Kb 94.8Kb 35.1Kb server.example.com => ip.address 1.23Mb 4.28Mb 1.12Mb <= 17.1Kb 83.5Kb 21.9Kb server.example.com => ip.address 395Kb 3.89Mb 1.07Mb <= 6.09Kb 109Kb 28.6Kb server.example.com => ip.address 4.55Mb 3.83Mb 1.04Mb <= 55.6Kb 45.4Kb 13.0Kb server.example.com => ip.address 649Kb 3.38Mb 1.47Mb <= 9.00Kb 38.7Kb 16.7Kb server.example.com => ip.address 5.00Mb 3.32Mb 1.80Mb <= 65.7Kb 55.1Kb 29.4Kb server.example.com => ip.address 387Kb 3.13Mb 1.06Mb <= 18.4Kb 39.9Kb 15.0Kb server.example.com => ip.address 3.27Mb 3.11Mb 1.01Mb <= 81.2Kb 64.5Kb 20.9Kb server.example.com => ip.address 1.75Mb 3.08Mb 2.72Mb <= 16.6Kb 35.6Kb 32.5Kb server.example.com => ip.address 1.75Mb 2.90Mb 2.79Mb <= 22.4Kb 32.6Kb 35.6Kb server.example.com => ip.address 3.03Mb 2.78Mb 1.82Mb <= 26.6Kb 27.4Kb 20.2Kb server.example.com => ip.address 2.26Mb 2.66Mb 1.36Mb <= 51.7Kb 49.1Kb 24.4Kb server.example.com => ip.address 586Kb 2.50Mb 1.03Mb <= 4.17Kb 26.1Kb 10.7Kb server.example.com => ip.address 2.42Mb 2.49Mb 2.44Mb <= 31.6Kb 29.7Kb 29.9Kb server.example.com => ip.address 2.41Mb 2.46Mb 2.41Mb <= 26.4Kb 24.5Kb 23.8Kb server.example.com => ip.address 2.37Mb 2.39Mb 2.40Mb <= 28.9Kb 27.0Kb 28.5Kb server.example.com => ip.address 525Kb 2.20Mb 1.05Mb <= 7.03Kb 26.0Kb 12.8Kb qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq TX: cum: 102GB peak: 1.65Gb rates: 1.46Gb 1.44Gb 1.48Gb RX: 1.31GB 24.3Mb 19.5Mb 18.9Mb 20.0Mb TOTAL: 103GB 1.67Gb 1.48Gb 1.46Gb 1.50Gb I check the transfer speed using iperf utility From Server A to Server B # iperf -c 0.0.0.2 -p 8777 ------------------------------------------------------------ Client connecting to 0.0.0.2, TCP port 8777 TCP window size: 85.3 KByte (default) ------------------------------------------------------------ [ 3] local 0.0.0.1 port 38895 connected with 0.0.0.2 port 8777 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.8 sec 528 KBytes 399 Kbits/sec My Current Connections in Server B # netstat -an|grep ":8777"|awk '/tcp/ {print $6}'|sort -nr| uniq -c 2072 TIME_WAIT 28 SYN_RECV 1 LISTEN 189 LAST_ACK 139 FIN_WAIT2 373 FIN_WAIT1 3381 ESTABLISHED 34 CLOSING Server A Network Card Information Settings for eth0: Supported ports: [ TP ] Supported link modes: 100baseT/Full 1000baseT/Full 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 10000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 0 Transceiver: external Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes Server B Network Card Information Settings for eth2: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: Direct Attach Copper PHYAD: 0 Transceiver: external Auto-negotiation: off Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes ifconfig server A eth0 Link encap:Ethernet HWaddr 00:25:90:ED:9E:AA inet addr:0.0.0.1 Bcast:0.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1202795665 errors:0 dropped:64334 overruns:0 frame:0 TX packets:2313161968 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:893413096188 (832.0 GiB) TX bytes:3360949570454 (3.0 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2207544 errors:0 dropped:0 overruns:0 frame:0 TX packets:2207544 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:247769175 (236.2 MiB) TX bytes:247769175 (236.2 MiB) ifconfig Server B eth2 Link encap:Ethernet HWaddr 00:25:90:82:C4:FE inet addr:0.0.0.2 Bcast:0.0.0.2 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:39973046980 errors:0 dropped:1828387600 overruns:0 frame:0 TX packets:69618752480 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3013976063688 (2.7 TiB) TX bytes:102250230803933 (92.9 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:1049495 errors:0 dropped:0 overruns:0 frame:0 TX packets:1049495 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:129012422 (123.0 MiB) TX bytes:129012422 (123.0 MiB) Netstat -i on Server B # netstat -i Kernel Interface table Iface MTU Met RX-OK RX-ERR RX-DRP RX-OVR TX-OK TX-ERR TX-DRP TX-OVR Flg eth2 9000 0 42098629968 0 2131223717 0 73698797854 0 0 0 BMRU lo 65536 0 1077908 0 0 0 1077908 0 0 0 LRU I Turn up send/receive buffers on the network card to 2048 and problem still persist I increase the MTU for server A and problem still persist and i increase the MTU for server B for better connectivity and transfer speed but it couldn't transfer at all The problem is : as you can see from iperf utility, the transfer speed from server A to server B slow when i restart network service in server B the transfer in server A at full speed, after 2 minutes , it's getting slow How could i troubleshoot slow speed issue and fix it in server B ? Notice : if there any other commands i should execute in servers for more information, so it might help resolve the problem , let me know in comments

  Read the article

• Force Direct3D anti-aliasing in a Direct3D game?

  - by James McLaughlin

  Some old games look really jagged nowadays on large displays without any anti-aliasing, but don't have any option built-in to the game to enable it. On a PC with an NVIDIA graphics card, it's possible to force anti-aliasing in the NVIDIA control panel which can really improve this. But I'm playing the game in Parallels on a Mac, and although the Mac has an NVIDIA graphics card, it's Parallels' emulated card that Windows sees and so obviously there's no NVIDIA control panel. Is there some generic way I can force anti-aliasing for a Direct3D game without using the NVIDIA control panel?

  Read the article

• webm html5 videos lose connection with apache server

  - by Jizbo Jonez

  webm html5 videos that are played through a domain on my server sometimes lose connection. A video that is playing will start to buffer and then stop part of way through with that message "Video playback aborted due to a network error." displayed on the html5 video player. I am delivering the webm videos via a php script on an LAMP server. There doesn't seem to be any errors in the server logs. Is there any php.ini settings or httpd.conf that I need to set? I recently set 'Keep Alive" to "on" in httpd.conf could that be causing this?

  Read the article

• Disable spell checking in IE 11 (Win 8.1)

  - by ComFreek

  I have the same Problem as described here: Disable spell checking in Internet Explorer 10 (Windows 8) My system: Windows 8.1 Pro 64-bit What I've already done: Deactivating the spelling options: (There may be minor differences between the following screenshot and the actual 8.1 display. I copied it from here because I own a German Version and I therefore thought that an English one would be simpler to understand.) I turned both options off and tried to restart IE. It's still "correcting" my texts. Searching for 'spelling correction' addons As said in the picture, this entry does not exist on my PC. (The following screenshot is taken from here) Is there any way of disabling it? I prefer an "official" solution if one is available. Otherwise, I also take any registry involving Solutions.

  Read the article

• Motherboard max memory supported

  - by Ashfame

  I have an Intel DG965RY motherboard and its specification says it supports 8GB with 533 or 667Mhz RAM sticks and only 4GB with 800Mhz RAM sticks. I am running a 64bit OS. I earlier had 2 X 1GB sticks (800Mhz), so I bought 2 X 2GB sticks (800Mhz) and I underclocked them in the settings to run at 667Mhz. Shouldn't it support all 6GB RAM now? It would be a bummer if I will specifically need 667Mhz sticks thinking that at the worst they will underclock and then run at 667Mhz. I tried this because I saw someone posted at some forum that he put in 4GB+ of RAM in the same board @ 800Mhz and the system uses it all. In my case (On Ubuntu), it only shows 3.2GB as of now (link to Question) so needed to confirm if this is a hardware limitation.

  Read the article

• Duplicate xserver

  - by hariks0

  When I start my ubuntu pc, just before my login, I receive a message that says "An xserver is already started in display :0. Would you like to try starting xserver in another virtual workspace?". Now If I answer 'No' the message appears again and again. If I say 'Yes' It goes to gnome desktop in virtual desktop 9 [Ctrl+Alt+F9] It was previously available only in [Ctrl+Alt+F7] but now available in both F7 and F9. Now I assume that there are two instances of xserver both in [Ctrl+Alt+F7] and [Ctrl+Alt+F9]. I think by killing one instance of xserver manaually I can disable the message. How do I do this? Thanks in advance.

  Read the article

• How to quickly switch monitors on multi-monitor setup? (W7)

  - by Saxtus

  At my desktop PC, I have 3 displays hooked up on my Palit GeForce GTX 480 to extend my desktop: DVI: Samsung SyncMaster T220 (22" 16:10, 1680x1050, as my main) DVI: Samsung SyncMaster 940BF (19" 4:3, 1280x1024) HDMI: Sony Bravia KDL-32D3000 (32" 16:9, 1360x768) As expected, the GFX card can only utilize 2 of the displays at any given time, so I have to manually switch using Windows' "Display Properties" dialog, each time I want to switch between them. I've tried UltraMon, DisplayFusion and PowerStrip (so please don't refer me to a question where those are given as solutions) but they are unable to switch monitors. Instead they can only change display resolutions and settings on the existing active monitors, with specially weird results when I've saved the monitor states and then tried to switch monitors using the saved states! Any idea on how to bypass the awful "Display Properties" dialog and it's "confirm your change" timer? Thanks in advance.

  Read the article

• Factory Reset Asus

  - by Ben

  I have an ASUS All-in-one PC (not sure what model) and I'm trying to perform a Factory Restore but nothing is working yet. I have tried pressing F8, all I had access to was "Restore from an earlier point" - Today was the earliest point; and "Restore from an Image" - which I don't have. I have tried pressing F9, F10, and F11, but all that brought me was options to Start Windows normally, Run a system diagnostic, or try other options (F8 menu). I don't have any other discs to restore from or anything, and I have found a tutorial to try and create a Partition(?) to load the restore from that. Does anyone have any other ideas?

  Read the article

• How to get rid of diacritics on my keyboard?

  - by stevenvh

  I searched Google and SU for my problem, but everybody seems to want to add diacritics, while I don't want them. I'm using Windows 7 and have a US keyboard installed, not the international version. Despite that some keys, like ", ^ and ~ are used for diacritics, which means that I have to type "SPACE to get a double quote. How do I get rid of this? My other PC, with the same settings, doesn't show this behavior. edit re Stefan's answer I don't see the icon Stefan refers to in my taskbar, probably because I have Classic Shell installed. But this is a screenshot of the Input Languages dialog, there are no other keyboards installed:

  Read the article

• Setting Redmine path

  - by David Parunakian

  Hello, How can I set the path on which Redmine should be run, e.g. example.com:3000/redmine instead of example.com:3000? There is an appropriately named option in the settings panel, but it serves a different purpose, according to the documentation and experimental observations (it is used to write URL in emails sent to users). A wider picture: I need this in order to properly serve Redmine on port 80 over Apache's mod_proxy (i.e. at example.com/redmine). The problem is that when running it on /, the home page fails to load the necessary resources (such as JavaScript and CSS files). Any workarounds?

  Read the article

• Windows not booting, bcd corrupt?

  - by Bolaji Ibrahim

  The windows boot configuration data file does not contain a valid OS entry Windows failed to start. A recent hardware or software change might be the case.to fix the problem: 1.Insert your windows installation disc and restart your computer. 2.Choose your language settings, and click "next" . 3.Click "repair your computer." If you do not have this disc, contact your administrator or computer manufacture for assistance. File: \Boot\BCD Status:Oxc0000098 Info :The windows boot configuration data does not contain a valid OS entry.

  Read the article

• Recommendations for managing dedicated server DNS

  - by KP Overflow

  I've rented a dedicated server for several years with a number of domains. I've got a coding background so am comfortable with that side of the tech, but I hate that I still don't truly understand DNS settings. Example: My provider (hostgator) just told me that my parent nameservers are not correctly configured as there is no A record for my primary nameserver. What book/link/tutorial should I read to go from kind of understanding that comment to really understanding it & knowing exactly what I need to do to fix it rather than trial & error which is what I usually do. Thanks BTW I'm using a WHM/cpanel linux setup at hostgator but am eager to learn the fundamentals.

  Read the article

• Create access point (uap0) on debian 7(arm) - not found?

  - by ethrbunny

  I'm working with a fanless PC that has an ARM chipset, 2 eth plugs and a wifi card (among other things). If I install debian 6 on it all three network interfaces are available at boot time. Today I tried to install debian 7 and had numerous errors indicating that the wireless card isn't supported. uap0: error fetching interface information: Device not found SIOCSIFADDR: No such device uap0: ERROR while getting interface flags: No such device uap0: ERROR while getting interface flags: No such device No such device ERR:UAPHOSTCMD is not supported by uap0 ERR:Command sending failed! No such device ERR:UAPHOSTCMD is not supported by uap0 ERR:Command sending failed! I've tried comparing the kernel module list to the working system but there are too many other differences to make something obvious enough (to me) stand out. How would I get started debugging this problem?

  Read the article

• VMWare guest OS is not using full hard drive space

  - by syuusuke

  Hey everyone, I'm wondering if you can give me some insight on how to figure this out. I've recently virtualized a w2k3 server that had 10GB C:\ drive size. Once I finished virtualizing it, I expanded the disk to 20GB for C:\ and within guest OS (W2K3) computer management settings, you can see it recognizes as 20GB partition C:. But for some reason, if I opened windows explorer and see the properties of C:\, it will only show total size of 10GB. Does anyone know how to solve this or even had this problem before?

  Read the article

< Previous Page | 491 492 493 494 495 496 497 498 499 500 501 502  | Next Page >