Search Results

Search found 2795 results on 112 pages for 'nic strong'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 5/112 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • Setting my NIC to full duplex

    - by David
    I am trying to optimize the network speed of my Solaris X86 server, and have discovered that the Cisco 3548 that it is connected to has issues with the NIC in my server. The NIC appears to have not been configured fully, and is coming up 100 half-duplex. The 3548 ports are all set to 100 full. Ideally I'd like to have the server set for 100 full, and have been attempting to configure it using ndd commands. However I have had no results. The following command: -bash-3.00# dladm show-dev rtls0 link: unknown speed: 100 Mbps duplex: unknown The NIC shows up as: pci bus 0x0001 cardnum 0x06 function 0x00: vendor 0x10ec device 0x8139 Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ which should be configurable. I have modified the configuration file from auto config (5) to 100 fdx (4) to no avail. If there is no other choice, I could alter the Cisco 3548 to be 100 half-duplex. However, this solution causes huge performance loss. Currently throughput is about 500Kbps, when it should be around 40Mbps.

    Read the article

  • qemu -cdrom ubuntu.iso -boot d -net nic,model=virtio -m 1024 -curses

    - by Gert Cuykens
    How do I disable frame buffers in Ubuntu 13.10 Saucy kernel, I tried all kinds of kernel parameters but none work? DEFAULT ramdisk LABEL ramdisk kernel /casper/vmlinuz append boot=casper toram initrd=/casper/initrd.img -- vesafb.nonsense=1 LABEL isotest kernel /casper/vmlinuz append boot=casper integrity-check initrd=/casper/initrd.img -- vesafb.nonsense=1 LABEL memtest kernel /install/memtest append - DISPLAY isolinux.txt TIMEOUT 300 PROMPT 1

    Read the article

  • Hyper-V: Dedicated NIC for Guests VMs

    - by TheLizardKing
    I have two NIC cards and created a private virtual network for my virtual machines and unchecked "Allow management operating system to share this network adapter" which basically turns my Guest NIC into this sorta shell of a NIC card on the host machine and the only thing checked in it's properties is "Microsoft Virtual Network Switch Protocol" which I am fine with. Everything works and everything is connected. My issue is that for some reason my guest (Ubuntu Server with legacy network drivers) is not talking properly to my DHCP server. Specifically my DHCP server reserves the guest's IP address using it's MAC address but the guest isn't picking it up. It's picking up any old IP it can get and I can't even ping the hostname from another PC on the network but it pings fine if I use the IP. I see the guest showing up in my DHCP table but I can't get the reservation to stick. Is there some reason it's only partially communicating with my DHCP server? Pinging it's hostname on itself reveals it's using 127.0.0.1 instead of it's network IP. Is this an issue with the legacy drivers used in Hyper-V?

    Read the article

  • Davicom DM9601 USB LAN NIC Ubuntu 11.10 issue

    - by Gaurav_Java
    I have a davicom dm9601 USB ethernet card. When I plug in the device, it is detected and drivers are loaded, but I can't connect to internet using it. It works perfectly on XP, other laptop but not working on Ubuntu 11.10 How can I install the driver for this? I have tried many things But nothing is working. If I go to this link driver but not compiling or may I be doing something wrong. I found this one but don't know how to follow these steps . This is my lsusb output: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 004: ID 064e:a103 Suyin Corp. Acer/HP Integrated Webcam [CN0314] Bus 003 Device 002: ID 08ff:1600 AuthenTec, Inc. AES1600 Bus 005 Device 002: ID 0a46:9601 Davicom Semiconductor, Inc. DM9601 Fast Ethernet Adapter Bus 006 Device 002: ID 046d:c045 Logitech, Inc. Optical Mouse Bus 003 Device 003: ID 0a5c:2101 Broadcom Corp. Bluetooth Controller Bus 004 Device 002: ID 04d9:1702 Holtek Semiconductor, Inc. But when I connected my Internet from different system its start working.

    Read the article

  • dhcp3-server (dhcpd) is tampering with host NIC

    - by user61000
    Hi all, I have a debian box that is serving as a router (using iptables NAT). When first turned on, everything works fine for a few minutes. Then the dhcp server assigns an IP (other than 192.168.0.1) to its' host NIC, eth0. This is NOT what I want. I just want dhcp3-server to listen on eth0, not assign it an IP, and changes the kernel routing table. This of course ruins the NAT capablities of the box. How can I tell the dhcp3-server NOT to do this? Thanks Before dhcp3-server tampers with eth0, the IP is 192.168.0.1, and the routing table looks like this: ~# netstat -r Kernel IP routing table Destination Gateway Iface 192.168.0.0 * eth0 173.33.220.0 * eth1 default 173.33.220.1 eth1 After dhcp3-server tampers with eth0, the IP is 192.168.0.3, and the routing table looks like this: ~# netstat -r Kernel IP routing table Destination Gateway Iface 192.168.0.0 * eth0 173.33.220.0 * eth1 default 192.168.0.1 eth0 default 173.33.220.1 eth1 SETUP Outbound NIC is eth1 Internal NIC is eth0 /etc/network/interfaces ... iface eth0 inet static address 192.168.0.1 netmask 255.255.255.0 /etc/default/dhcp3-server INTERFACES="eth0"

    Read the article

  • Using Ops Center to Provision Solaris using a Card-Based NIC

    - by Larry Wake
    Scott Dickson writes:  "Here's what I want to do:  I have a Sun Fire T2000 server with a Quad-GbE nxge card installed.  The only network is connected to port 2 on that card rather than the built-in network interfaces.  I want to install Solaris on it across the network, either Solaris 10 or Solaris 11." See what he did, using Oracle Enterprise Manager Ops Center 12c. [Read More]

    Read the article

  • VMWare hypervisor with only 1 network card?

    - by Rafiq Maniar
    VMWare hypervisor minimum requirements states that the minimum network requirements is: one NIC, plus one for Management interface (source: http://www.vmware.com/products/datacenter-virtualization/vsphere-hypervisor/requirements.html) It used to be possible to use 1 NIC only. Is anybody using the new versions of VMWare in this configuration? I ask because my colo provider will only provide me with 1 uplink (my server does have 2 NICs). I need to be able to run the VMs and also have remote management using only 1 NIC. Possible?

    Read the article

  • Bind nic to VM on VMware ESXi 5

    - by lewis
    I have physical server with 2 Broadcom NIC's. First NIC connected to local network, via this connection we can: Connect to ESXi hypervisor (hypervisor has local ip, e.g. 192.168.1.5) Connect to VM on this hypervisor (VM has network adapter, with local ip, e.g. 192.168.1.6) Second NIC connected to "global" network. Via second link(and public IP), we can have access to VM from Internet. How I may setup VM to use second NIC's connection?

    Read the article

  • 3 Servers, 2 Work Fine, One Has Network Issues

    - by ScaleOvenStove
    i have 3 servers, all relatively the same hardware/config, etc. I run some data pulls on all 3, and on 2 of them, they have 1 nic, and they work fine. On the other , there are 2 nics, and unless they are both plugged in or teamed, the processes time out. Any ideas on why this would be? It doesn't make sense to me, as the other two work fine with 1 nic and don't time out when running the same processes.

    Read the article

  • "System cannot find the file specified" trying to reinstall network driver.

    - by Justin Love
    After uninstalling Symantec Enpoint Protection (manually) one computer (Windows XP) has an inoperative NIC; it shows up in device manager as conflicted. I tried doing a windows repair from CD, which did not improve the situation. When I went to reinstall the drivers, driver installation failed with: Cannot install this hardware The system cannot find the file specified I've deleted the NIC in device manager without improvement.

    Read the article

  • Should I enable "Intel NIC DMA Channels"?

    - by javapowered
    I have HP DL360p Gen8 646902-xx1 I'm trying to optimize my config for low latency trading. Should I enable "Intel NIC DMA Channels"? Will that help/affect my system? From HP doc: Added a new ROM Based Setup Utility (RBSU) Advanced Performance Option menu that allows the user to enable Intel NIC DMA Channels (IOAT). This option is disabled by default. When enabled, certain networking devices may see an improvement in performance by utilizing Intel's DMA engine to offload network activity. Please consult documentation from the network adapter to determine if this feature is supported.

    Read the article

  • VMXNET3 nic loses the ability to update ARP table after N hours

    - by Peter
    I have a fedora 18 VM that stops updating the arp table on eth1 after running for a number of hours to days. There are other VMs on the same hypervisor that can access all of the same networks without issue. A tcpdump of the offending NIC shows only ARP broadcasts but no responses. None of the other VMs on the vDS see the ARP broadcasts from the offending NIC. The only way I can currently solve the problem is to reboot the VM and then everything works for a while. I've tried changing the port on the vDS and even flipping the network configurations after I lose eth1's ARP table, but the ARP problem follows eth1 but I can access the machines that were originally on eth1. If I statically add the arp entries for machines on the same subnet I have no problems with connectivity. The Hypervisor is an HP BL49X series with flex-10 network modules. Has anyone seen anything like this before?

    Read the article

  • Virtual NIC on VM couldn't ping externally after Vmotion

    - by ToreTrygg
    Today I vmotioned 5 MS SQL 2005 servers over to a new DRS Cluster. All SQL servers use the "Production_LAN" network and a single virtual NIC of type "VMXNET 3". The first 4 SQL VM (Windows 2003 Standard or Enterprise x32 bit) vmotioned over without a hitch. The last SQL VM I vmotioned (Windows 2003 Standard x64 bit R2) vmotioned over without error, but I upon completion, I could no longer ping the VM. I went into the VM and could not even ping the gateway, however I could ping the loopback. This SQL server is extremely busy in comparison with the previous 4 VM's. I restarted the server and it came back up with the virtual nic working just fine. The build of both servers (vmotioner and vmotionee) is ESX 4.0.0 175625 - So, pre-update 1. Should I suspect the network switch/VM for possibly not updating the mac table on the switch? Anybody else ever have this issue or know what may have caused it? Thank you!

    Read the article

  • CPU load, USB connection vs. NIC

    - by T.J. Crowder
    In general, and understanding the answer may vary by manufacturer and model (and driver, and...), in consumer-grade workstations with integrated NICs, does the NIC rely on the CPU for a lot of help (as is typically the case with a USB controller, for instance), or is it fairly intelligent and capable on its own (like, say, the typical Firewire controller)? Or is the question too general to answer? (If it matters, you can assume Linux.) Background: I'm looking at connecting a device (digital television capture) that will be delivering ~20-50 Mbit/sec of data to a somewhat under-powered workstation. I can get a USB 2 High-speed device, or a network-attached device, and am interested in avoiding impacting the CPU where possible. Obviously, if it's a 100Mbit NIC, that's roughly half its theoretical inbound bandwidth, whereas it's only roughly a tenth of the 480 Mbit/second the USB 2 "High Speed" interface. But if the latter requires a lot of CPU support and the former doesn't...

    Read the article

  • NIC: Changing Link Speed & Duplex to Full Duplex Is Drastically Slower

    - by rism
    I have an old Win Xp box with a 100 PRO/100 VE NIC and connecting to a Win 7 box with gigabit NIC via an ASUS gigabit router and peer to peer. I was getting 76% network utilisation on the XP machine using AUTO as the value for Link Speed and Duplex which is fine. But I decided to see what would happen if i selected Full Duplex 100Mbps on the XP box. I thought at worst it would be as good as auto detect since the Win 7 box it's transferring to is faster. Instead network utilisation dropped to 0.12% (as in a 10th of a percent) and the transfers just timed out. No biggie to reverse back to Auto but my question is why is full duplex such a dog? Im not "stuck" but just dont understand. There are only 2 machines here connecting through a router so i cant see how that would cause alot of collisions etc (if thats the problem).

    Read the article

  • Missing Jumbo and MTU for Broadcom NIC?

    - by Mike
    I have two Broadcom BCM5708C NetXtreme II GigE NICs in my Dell Windows SBS 2008 server. I would like make one them them Jumbo Frames enabled so that I can add it to my SAN whose VLAN on the switch is already using 9000 MTU. Broadcom's own data sheet for this NIC claims that it is Jumbo Frame capable up to a 9000 MTU. The problem is that there is no setting for Jumbo or MTU in the NIC's configurable settings. There are other settings but just not the one I need to change. Am I missing something here? The driver claims to be up-to-date when I allow Windows to search on-line.

    Read the article

  • Failover NIC with Windows 7 running Apache Server

    - by Benjamin Jones
    I have a Apache Server running on a Windows 7 Desktop for a internal website (Intranet). I am trying to figure out how I can make this system as failover safe as possible. One thing I want to do is use the 2nd NIC card that is currently disable. I only have one gateway address to my router. I do not have any computer running a Server O/S. If NIC1 crashes by chance(just humor me!), how could NIC2's IP take on the host name (I have mapped in host file) . I don't really care if the static IP of NIC2 changes seeing that the host name is the only thing I need. Could I add two IP's to the host file, with same host email and maybe create some script that will run IF NIC 1 fails? OR is there any failover software that will do this for me?

    Read the article

  • vmdk to live cd - VMware vmxnet virtual NIC driver Kernel panic

    - by ronalchn
    Task I am trying to convert a virtual machine to a live CD. Specifically, the virtual machine I am trying to convert is the IOI 2013 Competition Environment. In this task, I am aided by a guide Converting a virtual disk image: VDI or VMDK to an ISO you can distribute. Symptoms However, after getting through all the instructions, the live CD causes a kernel panic on boot on bare metal. In particular, the screen shows: [0.737348] cdrom: Uniform CD-ROM driver Revision: 3.20 [0.737503] sr 3:0:0:0: >Attached scsi CD-ROM sr0 [0.737638] sr 3:0:0:0: >Attached scsi generic sg2 type 5 [0.737771] Freeing unused kernel memory: 756k freed [0.738093] Write protecting the kernel text: 5960k [0.738155] Write protecting the kernel read-only data: 2424k [0.738224] NX-protecting the kernel data: 4280k Loading, please wait... [0.752252] udevd[100]: starting version 175 [0.768708] VMware vmxnet3 virtual NIC driver - version 1.1.29.0-k-NAPI [0.781204] VMware PVSCSI driver - version 1.0.2.0-k [0.789555] VMware vmxnet virtual NIC driver [0.799356] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000200 [0.799356] [0.799472] Pid: 1, comm: init Tainted: G 0 3.5.0-17-generic #28-Ubuntu [0.799549] Call Trace: [0.799603] [<c15bf0ec>] panic+0x81/0x17b [0.799654] [<c104a6a5>] do_exit+0x745/0x7a0 [0.799707] [<c104a9a4>] do_group_exit+0x34/0xa0 [0.799760] [<c104aa28>] sys_exit_group+0x18/0x20 [0.799813] [<c15cff5f>] sysenter_do_call+0x12/0x28 Possible problem I suspect that the problem is the VMware vmxnet virtual NIC driver - however, I do not know how I can uninstall it, and possibly install one for a bare metal machine. If anyone knows which packages needs installing/uninstalling at the .rootfs/ chroot directory stage, please let me know. Details on procedure Do note that after importing the .ova file into Virtualbox, the virtual machine is stored as a .vmdk file already, and not a .vdi file. I would like to point out some results of the procedure followed in case of any questions. This is after extracting the filesystem from the .raw file to the .rootfs/ directory mentioned in the blog. I changed the filesystem table as mentioned in the blog, then looked at the possible "kernel optimized for virtualization". However, I found that linux-image-generic was already installed. Also, when running the command dpkg-query --showformat='${Package}\n' -W 'vmware-tools*' (or dpkg-query --showformat='${Package}\n' -W '*-virtual'), no packages were found. Thus, I did not find any virtualization specific packages. I proceeded to generate the iso following the steps in the blog, and burned it to a DVD.

    Read the article

  • Hyper-V with a single host NIC

    - by Cylindric
    I'm trying to create a simple Hyper-V test machine, and am having more problems than expected with the basic networking. All other hypervisors I've used (vmware server, vmware player, virtualbox) allow me to use the default single NIC in my machine, and then create guests with "bridged" mode so they appear like a normal machine on the network. With the Hyper-V server, when I create a Virtual Switch and set it to "external", I lose all network access from the host. The solutions I've seen online seem to rely on complex configurations requiring multiple vSwitches and RRAS on the host to get it going. Is it really that complex to get a simple, single-NIC Hyper-V server going, in such a way that I can still use the host? The host is Windows 8.

    Read the article

  • Multiple IPs on firewall, are these virtual interfaces or what?

    - by Jakobud
    We have 5 static IP addresses from our ISP: XXX.XXX.XXX.180 XXX.XXX.XXX.181 XXX.XXX.XXX.182 XXX.XXX.XXX.183 XXX.XXX.XXX.184 On our firewall box, the NIC that is connected to our cable modem, appears to have all 5 IP addresses set on it. A previous IT guy set this thing up, and I'm not sure exactly what he did. Are these virtual interfaces on this NIC or what? Here is my ip addr output for that NIC: rwd0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether XX:XX:XX:XX:XX:XX brd ff:ff:ff:ff:ff:ff inet XXX.XXX.XXX.180/24 brd XXX.XXX.XXX.186 scope global rwd0 inet XXX.XXX.XXX.181/29 brd XXX.XXX.XXX.186 scope global rwd0:FWB9 inet XXX.XXX.XXX.182/29 brd XXX.XXX.XXX.186 scope global secondary rwd0:FWB10 inet XXX.XXX.XXX.183/29 brd XXX.XXX.XXX.186 scope global secondary rwd0:FWB11 inet XXX.XXX.XXX.184/29 brd XXX.XXX.XXX.186 scope global secondary rwd0:FWB12 inet6 fe80::250:8bff:fe61:5734/64 scope link valid_lft forever preferred_lft forever I'm a bit new to firewalls and networking so I'm just trying to figure out what he had going on here. I know he used Firewall Builder to configure the iptables rules, maybe that has something to do with the "FWB" I see in those names? So my questions are: What is going on here? Virtual Interfaces? Or something else? If we want to put in a second firewall in parallel with this firewall but we only want it to handle traffic to XXX.XXX.XXX.182, how do we get rid of the static XXX.XXX.XXX.182 address on this existing firewall box?

    Read the article

  • One Comcast Business Gateway, One Router, Two Web Servers

    - by Kevin Scheidt
    I have a Comcast business account with a router and a web server (info) attached. behind the router there are multiple computers and a second web server (info) which also serves as a file server. (info) has two nics in it. One direct to comcast and one connected to the router. It needs to serve the world it's websites. It needs however, to also be able to see all the internal computers and (com)'s served files. With just 1 nic (the one connected to the router, not comcast), (info) works fine but no one outside can see it. (com) services port 80 and (info) needs to handle port 80 as well. I have two domain names registered, and 5 static ip's from comcast. right now h t t p: / /www.graceamazing.com handled by (com) works fine and h t t p: / /www.graceamazing.com:1307 handled by (info) works fine. but as soon as I enable the 2nd nic in (info) h t t p: / /www.graceamazing.info runs extremely slow (Horribly slow). however, h t t p: / /www.graceamazing.com:1307 and .com work fine. (com) has an ip address via the router 70.89.233.41 (info) has a ip addy of 70.89.233.46 via comcast (2nd nic) and a internal ip of 192.168.x.100 via static behind the router. Any suggestions or changes to make that will make h t t p: / /www.graceamazing.info perform with the same speed it has when going through h t t p: / /graceamazing.com:1307 is there a setting I should check / could have misssed?

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >