Search Results

Search found 135 results on 6 pages for 'sdd'.

Page 5/6 | < Previous Page | 1 2 3 4 5 6  | Next Page >

  • repair partition table

    - by m.sr
    Hallo. I've just overwritten my partition table of my system's hard disk. i made a cfdisk on the wrong device (/dev/sda instead of /dev/sdd), deleted all partitions, made one new primary spanning over the whole device, set its type to 07 (NTFS) and hit write. So here i am with my system running. Until i reboot, i hope/guess nothing will change - meaning: all my data is accessible (I'm currently making a dd-backup of the whole device and plan to make a .tar.gz-backup of the most important data later). I also backed up /proc/partitions, /proc/diskstats (even though i guess this is more about throughput and stuff like this ...) and /sys/block/sda/sda?/{start,size}. Some further things i know: 4 primary partitions 1st partition: ~100Mb, ext3, /boot 2nd partition: ~100Mb, "Win7 Boot Partition", ntfs(?) 3rd partition: ~20...30GB, Win7, ntfs 4th partition: ~20...30GB, luks-encrypted device The luks- de crypted device is a LVM-PV The /, /home & swap-partitions are all LVs on the (VG on the) above noted PV So my questions: What is the simplest way to just write the kernels partition table to the disk? What is the simplest way to take the above mentioned (and perhaps other I don't know of ...) data and generate the partition table? Are there any problems to take care of regarding to luks and/or lvm? Is there any data I should backup before rebooting (meanig stuff from kernel [ /sys/..., /proc/...] and so on, which could help me regenerate the partition table)? Thanks a lot! P.S.: debian sid, Kernel 2.6.34-1-amd64 from debian-experimental, 80GB Intel SSD

    Read the article

  • Move an existing RAID 5 array from Ubuntu to Gentoo

    - by Cocoabean
    I have a 64-bit Ubuntu machine with a 4-disk RAID 5 using software raid (md). I've been able to boot an Ubuntu LiveCD and recognize the array with a simple mdadm -A /dev/md0. It was easy to mount after that and nothing had to rebuild. I'm installing Gentoo on this box now (multi-boot, non-RAID root partition) and I have md auto-detect turned on in the kernel. When I boot Gentoo I get: "invalid superblock magic on sdd" for each of the drives in the array. I boot back to Ubuntu and they mount no problem. I tried copying the mdadm.conf that works in Ubuntu to Gentoo, and then ran mdadm -A /dev/md0 but it reports that there is no array named md0. I don't want to lose data (obviously) and I don't want to have to let the RAID rebuild every time I switch between OSes. Any help is appreciated. Both are using mdadm 3.1.4 Both are running 64-bit kernels. mdadm -D /dev/md0 from Ubuntu yields: http://pastebin.com/5gj2QNkV UPDATE: After rebooting I noticed that it still complains about invalid blocks, but cat /proc/mdstat shows an inactive /dev/md127 with the same disks as my raid. I want to mount it but I don't want to get stuck waiting for a rebuild or destroying it inadvertently. mdadm -D /dev/md127 Here is pastebin of mdadm -D /dev/md127 on gentoo: http://pastebin.com/gDCWn0Rn UPDATE II: dmesg output about 'invalid raid superblocks' http://paste.ubuntu.com/885471/ fdisk -l from Ubuntu, /dev/md0 does not have any partitions but I do have it mounted and accessible: http://paste.ubuntu.com/885475/

    Read the article

  • What do you upgrade to make games load faster? [on hold]

    - by Superbest
    Let's say you have a relatively modern game like Shogun 2. The loading screens take several minutes. This bothers you and you'd like to improve it. What is actually going on when loading screens are up? I'm guessing assets are being loaded into memory from disk, and possibly being decompressed first. However, what is actually causing the slow down? The memory? Mainboard? CPU? HDD? If you had $100 to spend on upgrades and your only goal is to speed up loading screens without reducing other performance, what component of the computer does it make sense to upgrade for maximum benefit? If your answer is "it depends on the existing setup", what sort of benchmarks would you run to determine what is causing the bottleneck? What if you had $500 instead? I give the two budgets for context. I am not asking for actual recommendations about which component to buy (nor are the numbers supposed to be rigid limits), but what features are important when shopping for components with small and large budgets (a large budget could allow buying multiple components which are not so good on their own, but work particularly well together). I mention Shogun 2 as an example, but I'm asking about reducing overall loading times, across all games, not just one game. Therefore, "put it on a solid state disk" probably won't be good solution, because putting every game on your SDD will quickly fill it up.

    Read the article

  • Write Fedora.iso to USB and boot it from a Macbook

    - by MTilsted
    I have an .iso image of the full Fedora 16 install (Downloaded from http://fedoraproject.org/en/get-fedora-options#formats as "Fedora 16 DVD") and the question now is: How do I write it on a USB stick, so I can install it on my Mac book? I tried using DD as the install guide said, and that gave me a USB stick which can boot from my PC. But it can't boot from the Mac (The Mac start menu don't show it as a boot option). Edit: I downloaded a live install image, and did this (SSD is my USB 4GB thing) /sbin/mkdosfs -F 32 -n usbdisk /dev/dev/sdd1 sudo livecd-iso-to-disk --format --reset-mbr --efi /tmp/download/Fedora-16-i686-Live-KDE.iso /dev/sdd1 And this produced an image which can boot on my pc but not on my mac. This seems to indicate that the --efi is not working, because if it really was EFI it would not boot on a normal pc, would it? I then tried this: (Difference being that I write the image directory to /dev/sdd instead of /dev/sdd1) but this still will not boot on the Mac (it newer shows up at the startup screen on the Mac). sudo livecd-iso-to-disk --format --reset-mbr --efi /tmp/download/Fedora- PS: My host Linux is Fedora 13.

    Read the article

  • How to create partition when growing raid5 with mdadm.

    - by hometoast
    I have 4 drives, 2x640GB, and 2x1TB drives. My array is made up of the four 640GB partitions and the beginning of each drive. I want to replace both 640GB with 1TB drives. I understand I need to 1) fail a disk 2) replace with new 3) partition 4) add disk to array My question is, when I create the new partition on the new 1TB drive, do I create a 1TB "Raid Auto Detect" partition? Or do I create another 640GB partition and grow it later? Or perhaps the same question could be worded: after I replace the drives how to I grow the 640GB raid partitions to fill the rest of the 1TB drive? fdisk info: Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xe3d0900f Device Boot Start End Blocks Id System /dev/sdb1 1 77825 625129281 fd Linux raid autodetect /dev/sdb2 77826 121601 351630720 83 Linux Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xc0b23adf Device Boot Start End Blocks Id System /dev/sdc1 1 77825 625129281 fd Linux raid autodetect /dev/sdc2 77826 121601 351630720 83 Linux Disk /dev/sdd: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x582c8b94 Device Boot Start End Blocks Id System /dev/sdd1 1 77825 625129281 fd Linux raid autodetect Disk /dev/sde: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xbc33313a Device Boot Start End Blocks Id System /dev/sde1 1 77825 625129281 fd Linux raid autodetect Disk /dev/md0: 1920.4 GB, 1920396951552 bytes 2 heads, 4 sectors/track, 468846912 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk identifier: 0x00000000

    Read the article

  • Move EFI System Partition to another drive

    - by Pincopallino
    I had a Windows 8 installation on an HDD, using UEFI as boot. The HDD has the following GPT table: DISKPART> list partition Partizione ### Tipo Dim. Offset --------------- ---------------- ------- ------- Partizione 1 Ripristino 300 Mb 1024 Kb Partizione 2 Sistema 100 Mb 301 Mb Partizione 3 Riservato 128 Mb 401 Mb Partizione 4 Primario 390 Gb 529 Mb Partizione 5 Primario 540 Gb 390 Gb (I apologize it's in Italian, but the translation is quite straightforward). I recently bought an SSD drive, connected it and installed a fresh Windows 8. Now I have a working dual boot, but the UEFI partition is on the HDD instead of the SSD. Here's the SDD partition list: Partizione ### Tipo Dim. Offset --------------- ---------------- ------- ------- Partizione 1 Riservato 128 Mb 1024 Kb Partizione 2 Primario 221 Gb 129 Mb I think that the best solution would be to have it on the SSD for two reasons: the first is performance (I guess it would be a little be faster on the SSD due to the spin up time for an HDD, but I may be wrong about that) second reason is consistency. As I plan to use only the Windows 8 installation that is located on the SSD and I'm probably going to erase the system partition on the HDD to use it as a data storage device, I think that the boot partition should be on the same drive as the OS. So the question is how do I move the EFI System Partition to the SSD?

    Read the article

  • Is it a good Idea to switch to a SSD to use less battery?

    - by Walter Maier-Murdnelch
    I am thinking of buying a SSD for my laptop, mainly for the purpose of extended operating time when running on battery. At the moment I use a Hitachi HTS545032B9A300 (320GB) (Datasheet) as main drive and a Seagate Momentus 5400.3 120GB as secondary drive. I dualboot Windows and Linux but I don't need the windows partition any longer, a 120GB SDD would be more than sufficient space-wise. Speed is not an issue for me, I make heavy use of tmpfs (ramdrive) within Linux and transfers of bigger files are mainly through some network filesystem anyways, thus a cheaper SSD should do. For the purpose of comparison I chose the OCZ Vertex Plus 120GB. Power consumption always is a big promotional thing the industry uses to make me want to buy their SSDs, some sheet on the OCZ page provides an astonishing comparison of desktop HDDS and SSDs. The numbers I got comparing my laptop HDD and their SSD were not really astonishing any longer. Hitachi 320GB HDD: Startup (W, peak, max.) 4.5 Seek (W, avg.) 1.7 Read / Write (W, avg.) 1.4 Performance idle (W, avg.) 1.3 Active idle (W, avg.) 0.8 Low power idle (W, avg.) 0.5 Standby (W, avg.) 0.2 Sleep 0.1 OCZ 120GB SSD: 1.5W active 0.3W standby I see that there are differences, but actually they don't seem that high as I though they were. And compared to the power consuption of the rest of my system I wonder if it makes a difference at all. Have I just taken the wrong look at the whole thing or may I be better off to buy another battery for my laptop?

    Read the article

  • Compatibility of Fedora install on a Hybrid drive

    - by kjh
    I recently bought un ultrabook with a 500gb/32gb sdd hdd hybrid drive, and I'm having trouble replacing windows on it with fedora seventeen. it errors out saying there was an unhandled exception. Is linux compatible with hybrid drives? or can the operating system on a hybrid drive not be replaced? Edit: here are the steps I select special storage devices because it ignores my hard drives otherwise at this point i get the message: "Disk contains bios raid meta data, disk sda will be ignored" I can pick a hostname, select my timezone and set a password at the install type screen, no matter what I select (use all free space, replace linux systems, create custom partition etc..) once I click next, it says "an unhandled exception" has occured. and I can no longer proceed with installation. Here is the error message: anaconda 17.29 exception report Traceback (most recent call first); File "/usr/lib64/python2.7/size-packages/pyanaconda/bootloader.py"; line 183 self.stage1_drive=self_drives[0] File "/usr/lib64/python2.7/site-packages/pyanaconda/rw/cleardisks_gui.ph"; line... and tons of more lines like that

    Read the article

  • When using software RAID and LVM on Linux, which IO scheduler and readahead settings are honored?

    - by andrew311
    In the case of multiple layers (physical drives - md - dm - lvm), how do the schedulers, readahead settings, and other disk settings interact? Imagine you have several disks (/dev/sda - /dev/sdd) all part of a software RAID device (/dev/md0) created with mdadm. Each device (including physical disks and /dev/md0) has its own setting for IO scheduler (changed like so) and readahead (changed using blockdev). When you throw in things like dm (crypto) and LVM you add even more layers with their own settings. For example, if the physical device has a read ahead of 128 blocks and the RAID has a readahead of 64 blocks, which is honored when I do a read from /dev/md0? Does the md driver attempt a 64 block read which the physical device driver then translates to a read of 128 blocks? Or does the RAID readahead "pass-through" to the underlying device, resulting in a 64 block read? The same kind of question holds for schedulers? Do I have to worry about multiple layers of IO schedulers and how they interact, or does the /dev/md0 effectively override underlying schedulers? In my attempts to answer this question, I've dug up some interesting data on schedulers and tools which might help figure this out: Linux Disk Scheduler Benchmarking from Google blktrace - generate traces of the i/o traffic on block devices Relevant Linux kernel mailing list thread

    Read the article

  • FDE / SSD - partition and leave some unencrypted?

    - by Web Design Hero
    Just bought a used beast of a desktop pc. The system drive is setup as a Raid 0 SSD (Intel 510 SSD Drives) with 128 each. I will probably not have to many programs beyond office and maybe Adobe CS if I spring for it, I will be keeping big data on a regular hdd. My question is about setting up TrueCrypt with my configuration. I have not previously done full disk encryption, but I feel that its probably a good idea. I have done some speed tests using file containers on the hdd and the sdd with truecrypt. While there is a huge hit with the SSDs and Truecrypt, it still outperforms the hdd on its own by a good margin, so I think i will be okay for my needs with truecrypt. I have seen in a few places that they recommend partitioning the drive and leavign some of the SSD not inside truecrypt, does this really make a difference? If so, how much should I leave? Will there be any issue in the Raid0 configuration? I am not really concerned about all the wear leveling issue, rather loose data and be secure, but since I don't need all that space neccesarily, I would like to optimize my setup for security and speed.

    Read the article

  • Using Solaris zfs + iscsi targets with Oracle VM

    - by wim.coekaerts
    I was playing with my Oracle VM setup and needed some shared storage that was block based. I did not have a storage array available but I did have a solaris box, that I use for Oracle VDI, available. I set up a few iscsi targets on this solaris server and exported them to my 2 Oracle VM servers. Here's how I did this : (1) On the solaris side : # zpool list NAME SIZE USED AVAIL CAP HEALTH ALTROOT rpool 544G 129G 415G 23% ONLINE - I just have a simple zpool, called rpool, on this box. It has plenty of space available for my needs. So I will use rpool and I will create 5 50gb vols : zfs create -V 50G rpool/ovm1 zfs create -V 50G rpool/ovm2 zfs create -V 50G rpool/ovm3 zfs create -V 50G rpool/ovm4 zfs create -V 50G rpool/ovm5 I want to use these volumes for iscsi so I have to enable them as shared iscsi devices : zfs set shareiscsi=on rpool/ovm1 zfs set shareiscsi=on rpool/ovm2 zfs set shareiscsi=on rpool/ovm3 zfs set shareiscsi=on rpool/ovm4 zfs set shareiscsi=on rpool/ovm5 The command iscsitadm list target should list these devices so make sure they show up. # iscsitadm list target Target: rpool/ovm1 iSCSI Name: iqn.1986-03.com.sun:02:896c766c-0943-4da5-d47e-9575b5a0be36 Connections: 2 Target: rpool/ovm2 iSCSI Name: iqn.1986-03.com.sun:02:a3116b46-73e0-e8c2-e80c-9a4f71aff069 Connections: 2 Target: rpool/ovm3 iSCSI Name: iqn.1986-03.com.sun:02:a838c400-2730-c0d6-f2c2-ee186a0261c1 Connections: 2 Target: rpool/ovm4 iSCSI Name: iqn.1986-03.com.sun:02:2e046afb-d66d-4f3f-c5de-8115e0ddd931 Connections: 2 Target: rpool/ovm5 iSCSI Name: iqn.1986-03.com.sun:02:66109fbe-81ac-ef05-f85e-ab8c1f34cb43 Connections: 2 At this point I want to make sure that I have some access control on these devices. To make it easier, I will create an alias for my 2 servers and use the alias for the ACL. get the iqn from the 2 servers on my 2 ovm servers (wcoekaer-srv1, wcoekaer-srv2) get the content of /etc/iscsi/initiatorname.iscsi (for each server) InitiatorName=iqn.1986-03.com.sun:01:2a7526f0ffff On the solaris side create the aliases : iscsitadm create initiator -n iqn.1986-03.com.sun:01:2a7526f0ffff wcoekaer-srv1 iscsitadm create initiator -n iqn.1986-03.com.sun:01:e31b08110f1 wcoekaer-srv5 Add the ACL to the targets : iscsitadm modify target -l wcoekaer-srv1 rpool/ovm1 iscsitadm modify target -l wcoekaer-srv1 rpool/ovm2 iscsitadm modify target -l wcoekaer-srv1 rpool/ovm3 iscsitadm modify target -l wcoekaer-srv1 rpool/ovm4 iscsitadm modify target -l wcoekaer-srv1 rpool/ovm5 iscsitadm modify target -l wcoekaer-srv5 rpool/ovm1 iscsitadm modify target -l wcoekaer-srv5 rpool/ovm2 iscsitadm modify target -l wcoekaer-srv5 rpool/ovm3 iscsitadm modify target -l wcoekaer-srv5 rpool/ovm4 iscsitadm modify target -l wcoekaer-srv5 rpool/ovm5 (2) the Oracle VM side On each server just do 2 simple things : # iscsiadm -m discovery -t sendtargets -p ca-vdi1 where ca-vdi1 is my solaris server name # service iscsi restart When I do cat /proc/partitions on my servers I will see the devices show up # cat /proc/partitions major minor #blocks name 8 0 160836480 sda 8 1 104391 sda1 8 2 3148740 sda2 8 3 1052257 sda3 253 0 6377804 dm-0 253 1 6377804 dm-1 253 2 6377804 dm-2 8 16 52428800 sdb 8 32 52428800 sdc 8 48 52428800 sdd 8 80 52428800 sdf 8 64 52428800 sde These 5 new devices sd[b..f] are shared storage for Oracle VM and can be used to pass through to the VM's as phy: devices or put ocfs2 on it and use as shared filesystem storage for dom0 repositories. I am setting up an 11gR2 rac template (the cool stuff Saar did) so I am using my devices to create a 2 node RAC cluster with phy: devices.

    Read the article

  • lvm disappeared after disc replacement on raid10

    - by user142295
    here my problem: I am running ubuntu 12.04 on a raid10 (4 disks), on top of which I installed an lvm with two volume groups (one for /, one for /home). The layout of the disks are as follows: Disk /dev/sda: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930277168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0003f3b6 Device Boot Start End Blocks Id System /dev/sda1 * 63 481949 240943+ 83 Linux /dev/sda2 481950 2910640634 1455079342+ fd Linux raid autodetect /dev/sda3 2910640635 2930272064 9815715 82 Linux swap / Solaris Disk /dev/sdb: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930277168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00069785 Device Boot Start End Blocks Id System /dev/sdb1 63 2910158684 1455079311 fd Linux raid autodetect /dev/sdb2 2910158685 2930272064 10056690 82 Linux swap / Solaris Disk /dev/sdc: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930277168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdc1 63 2910158684 1455079311 fd Linux raid autodetect /dev/sdc2 2910158685 2930272064 10056690 82 Linux swap / Solaris Disk /dev/sdd: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930277168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000f14de Device Boot Start End Blocks Id System /dev/sdd1 63 2910158684 1455079311 fd Linux raid autodetect /dev/sdd2 2910158685 2930272064 10056690 82 Linux swap / Solaris The first disk (/dev/sda) contains the /boot partition on /dev/sda1. I use grub2 to boot the system off this partition. On top of this raid10 I installed two volume groups, one for /, one for /home. This system worked well, I even exchanged two disks during the last two years. It always worked. But not this time. For the first time, /dev/sda broke. I do not know if this is an issue – I know I would have struggled anyways to overcome the problem with /boot installed on that disk and grub2 installed on the mbr of /dev/sda. Anyways, I did what I always did: start knoppix fire up the raid sudo mdadm --examine -scan which returns ARRAY /dev/md127 UUID=0dbf4558:1a943464:132783e8:19cdff95 start it up sudo mdadm --assemble /dev/md127 fail the failing disk (smart event) sudo mdadm /dev/md127 --fail /dev/sda2 remove the failing disk sudo mdadm /dev/md127 --remove /dev/sda2 stop the raid sudo mdadm -S /dev/md127 take out the disk replace it with a new one create the same partitions as on the failling one add it to the raid sudo mdadm --assemble /dev/md127 sudo mdadm /dev/md127 --add /dev/sda2 wait 4 hours All looks fine: cat /proc/mdstat returns: Personalities : [raid10] md127 : active raid10 sda2[0] sdd1[3] sdc1[2] sdb1[1] 2910158464 blocks 64K chunks 2 near-copies [4/4] [UUUU] unused devices: <none> and sudo mdadm --detail /dev/md127 returns /dev/md127: Version : 0.90 Creation Time : Wed Jun 10 13:08:46 2009 Raid Level : raid10 Array Size : 2910158464 (2775.34 GiB 2980.00 GB) Used Dev Size : 1455079232 (1387.67 GiB 1490.00 GB) Raid Devices : 4 Total Devices : 4 Preferred Minor : 127 Persistence : Superblock is persistent Update Time : Thu Mar 21 16:27:40 2013 State : clean Active Devices : 4 Working Devices : 4 Failed Devices : 0 Spare Devices : 0 Layout : near=2 Chunk Size : 64K UUID : 0dbf4558:1a943464:132783e8:19cdff95 (local to host Microknoppix) Events : 0.4824680 Number Major Minor RaidDevice State 0 8 2 0 active sync /dev/sda2 1 8 17 1 active sync /dev/sdb1 2 8 33 2 active sync /dev/sdc1 3 8 49 3 active sync /dev/sdd1 However, there is no trace of the volume groups. Rebooting into knoppix does not help Restarting the old system (I actually replugged and re-added the failing disk for that – the system begins to start, but then fails to see the / partition – no wonder if the volume group is gone) does not help. sudo vgscan, sudo vgdisplay, sudo lvs, sudo lvdisplay, sudo vgscan –mknodes all returned No volume groups found. I am completely at a loss. Can anyone tell me if and how I can recover my data? Thanks in advance!

    Read the article

  • Failed to unmount partitions

    - by msknapp
    I'm trying to install ubuntu from a pen drive. I have windows 7 installed already and want to keep that installation. I have a 3TB drive that has one 2TB partition on it, so the last 1TB is completely unused, which is where I want to install ubuntu. I started ubuntu in "try ubuntu" mode and then opened gparted, and then deleted the unused partition for the last third of my drive, then tried to install ubuntu. During the install, it asked me if I wanted to unmount the drives I already have The installer has detected that the following disks have mounted partitions: /dev/sda, /dev/sdb Do you want the installer to try to unmount the partitions on these disks before continuing? If you leave them mounted, you will not be able to create, delete, or resize partitions on these disks, but you may be able to install to existing partitions there. No, Yes I said no because I don't want to lose my windows 7 installation, nor any of that data. I wonder, if I had said yes above, would I have lost all the data on those drives? Anyways, I hit no and continued. I chose to install ubuntu alongside windows 7, and hit continue. A few minutes passed when this popup appeared: Failed to unmount partitions The installer needs to commit changes to partition tables, but cannot do so because the partitions on the following mount points could not be unmounted: /media/ubuntu/Three\ Terabyte Drive Terabyte\ DriveDrive Please close any applications using these mount points. Would you like the installer to try to unmount these partitions again? Go Back, Continue Why is this not working? What am I supposed to do? ========== Update: I went ahead and said yes, it can unmount those partitions. It finished installing Ubuntu, but now when i start my machine it just takes me to the grub rescue prompt. Seems like it broke something. What can I do now? =============== Results of fdisk -l: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00027e14 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 976771071 488282112 7 HPFS/NTFS/exFAT WARNING: GPT (GUID Partition Table) detected on '/dev/sdb'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sdb: 3000.6 GB, 3000592982016 bytes 255 heads, 63 sectors/track, 364801 cylinders, total 5860533168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 4294967295 2147483647+ ee GPT Partition 1 does not start on physical sector boundary. Disk /dev/sdc: 16.0 GB, 16008609792 bytes 255 heads, 63 sectors/track, 1946 cylinders, total 31266816 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdc1 * 32 31266815 15633392 c W95 FAT32 (LBA) Disk /dev/sdd: 999.5 GB, 999501594624 bytes 255 heads, 63 sectors/track, 121515 cylinders, total 1952151552 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0002ae3f Device Boot Start End Blocks Id System /dev/sdd1 2048 1952151551 976074752 7 HPFS/NTFS/exFAT

    Read the article

  • missing files after reassemble of RAID-5

    - by Kris_R
    I had to open my file-server's housing on Sunday to replace a faulty fan. What I didn't see was that one of the sata-cables was not properly connected. The 1st thing I did after a reboot was a check of the RAID status and it showed immediately that one drive is missing. Till this moment the device was not used (however it was mounted, so I'm not 100% sure that system did nothing). I stopped md0 and re-plugged the cable: mdadm --stop /dev/md0 poweroff After another reboot I checked the removed drive: mdadm --examine /dev/sdd1 ... Checksum : 3276bc1d - correct Events : 315782 Layout : left-symmetric Chunk Size : 32K Number Major Minor RaidDevice State this 0 8 49 0 active sync /dev/sdd1 0 0 8 49 0 active sync /dev/sdd1 1 1 8 65 1 active sync /dev/sde1 2 2 8 33 2 active sync /dev/sdc1 3 3 8 17 3 active sync /dev/sdb1 I was a bit surprised that it was shown as active (even if earlier mdadm said, that this device was removed from array) and its checksum was OK. I recreated RAID with: mdadm --assemble /dev/md0 --scan The command mdadm --detail /dev/md0 showed that all drives were running and system was in "clean" state. I mounted the device md0 and then came hic-cup. I wanted to work on one of the last files that I had been using before all the situation and it was not there. In another place I missed actually all files from the directory where I was working. As far as I can see most of the files that are older than a few days are intact but some newer ones are missing. Now the big question: what would be your advice? Is there a way to get these data? I thought about removing the drive that was earlier labeled by mdadm and rebuild array with another empty HDD. I've found that after re-assemble the "broken" drive has another label (changed from sdd to sdb). Can this have influence on rebuilt process? If yes, how to reassemble the array properly? I'm sure the SATA-cables are connected still in the same order to the controller. p.s. Please no advises like "restore from backup". I'm doing back-ups on Sunday's night and this happened in the late afternoon, so backup is not really options for me. p.s.s. I asked this question on Unix&Linux but no answer came up during last two days. I'm getting quite anxious. Sorry for duplicating if any of you reading the other forum.

    Read the article

  • What is some good lossless video codec for recording gameplay?

    - by Don Salva
    I'm an avid gamer and I like to record my gameplay. Usually I've been using Fraps to do it, however I'm thinking of switching to Dxtory as it allows to write on multiple HDDs at once. Say I have 3 HDDs with the following write speeds: HDD1 with 50 mb/s, HDD2 with 22 mb/s and HDD3 with 45 mb/s. Combined write speed would be: 117 mb/s. Dxtory allows you to utilize all 3 HDD's at once while recording your gameplay. Using this formula: RGB24 YUV24: Width x Height x 3 x fps = bitrate (byte/sec) YUV420: Width x Height x 3 / 2 x fps = bitrate (byte/sec) YUV410: Width x Height x 9 / 8 x fps = bitrate (byte/sec) And recording in YUV420 colorspace at 1920x1080 with 30 fps I'd need about 95 mb/s write speed. Dxtory is good because it allows me to play with constant 60 fps while recording in 30 fps. Fraps does not (even though they say it does), once you start recording with Fraps, the game's fps drops. So I'm looking for a codec that doesn't need a very high write speed (bitrate) yet records in good (lossless) quality. Dxtory comes with its own codec, the Dxtory codec. Which allows me some experimentation. Fraps has it's own codec which I can use in Dxtory to expirement around. I also came across http://lags.leetcode.net/codec.html . Are there more lossless codecs out there (besides Fraps' and Dxtory's) which are good for what I want to do? Edit: To clarify, yes, I'm aware a lossless codec always has "good" quality. But that's not what I'm looking for. Let me take the Fraps codec and Dxtory codec to clarify what I'm looking for. When I record with the Dxtory codec in RGB colorspace at 1920x1080 with targeted 30 fps, I can play the game at 60 fps, BUT I'm recording with 10-15 fps, that's because RGB with Dxtory needs much, much more write speed than my hdd can handle. When recording with Dxtory codec in YUV410 colorspace at 1920x1080 with targeted 30 fps, I can play at 60 fps and record at 30 fps, again, that's because YUV410 in Dxtory's codec takes much, much less write speed than RGB When recording with Fraps codec in ??? (I dunno the color space Fraps records in, I guess YUV420), I can play with 60 fps and record with 30 fps. What I'm looking for is a lossless codec that can record in YUV420 (or even RGB??) which does not exceed a write speed (or bitrate if you will) of 100 mb/s in 1920x1080 or in other words, which will allow me to record in constant 30fps. Obviously the best solution would be to buy an SDD, but that's not what I'm after.

    Read the article

  • Ubuntu 12.04 boot degraded raid

    - by beacon_bonanza
    I've installed Ubuntu 12.04.1 in a new server and set up the 4 hard drives with 3 RAID 1 devices, the configuration is such that the first two drives have md0 (swap space) and md1 (/) with the third and fourth drives having md2 (/var). I've been testing the operation under a drive failure and found that the system boots fine if I remove disk two but if I remove disk one then the system gets to grub and then just restarts. I'm confused as to why grub appears to be loading properly from disk two but then the boot fails. I've tried to copy the MBR from disk 1 to 2: dd if=/dev/sda of=/dev/sdb bs=512 count=1 but this didn't make a difference. Any ideas how to get it to boot from just the second disk? fdisk -l Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000ccfa5 Device Boot Start End Blocks Id System /dev/sda1 2048 31250431 15624192 fd Linux RAID autodetect /dev/sda2 * 31250432 3907028991 1937889280 fd Linux RAID autodetect Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000ccfa5 Device Boot Start End Blocks Id System /dev/sdb1 2048 31250431 15624192 fd Linux RAID autodetect /dev/sdb2 * 31250432 3907028991 1937889280 fd Linux RAID autodetect Disk /dev/sdd: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00035b05 Device Boot Start End Blocks Id System /dev/sdd1 2048 3907028991 1953513472 fd Linux RAID autodetect Disk /dev/sdc: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000c73aa Device Boot Start End Blocks Id System /dev/sdc1 2048 3907028991 1953513472 fd Linux RAID autodetect Disk /dev/md1: 1984.3 GB, 1984264208384 bytes 2 heads, 4 sectors/track, 484439504 cylinders, total 3875516032 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md2: 2000.3 GB, 2000263380992 bytes 2 heads, 4 sectors/track, 488345552 cylinders, total 3906764416 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0: 16.0 GB, 15990652928 bytes 2 heads, 4 sectors/track, 3903968 cylinders, total 31231744 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000

    Read the article

  • Very poor read performance compared to write performance on md(raid1) / crypt(luks) / lvm

    - by Android5360
    I'm experiencing very poor read performance over raid1/crypt/lvm. In the same time, write speeds are about 2x+ faster on the same setup. On another raid1 setup on the same machine I get normal read speeds (maybe because I'm not using cryptsetup). OS related disks: sda + sdb. I have raid1 configuration with two disks, both are in place. I'm using LVM over the RAID. No encryption. Both disks are WD Green, 5400 rpm. IO test results on this raid1: dd if=/dev/zero of=/tmp/output.img3 bs=8k count=256k conv=fsync - 2147483648 bytes (2.1 GB) copied, 22.3392 s, 96.1 MB/s sync echo 3 > /proc/sys/vm/drop_caches dd if=/tmp/output.img3 of=/dev/null bs=8k - 2147483648 bytes (2.1 GB) copied, 15.9 s, 135 MB/s And here is the problematic setup (on the same machine). Currently I have only one sdc (WD Green, 5400rpm) configured in software raid1 + crypt (luks, serpent-xts-plain) + lvm. Tomorrow I will attach another disk (sdd) to complete this two-disk raid1 setup. IO tests results on this raid1: dd if=/dev/zero of=output.img3 bs=8k count=256k conv=fsync 2147483648 bytes (2.1 GB) copied, 17.7235 s, 121 MB/s sync echo 3 > /proc/sys/vm/drop_caches dd if=output.img3 of=/dev/null bs=8k 2147483648 bytes (2.1 GB) copied, 36.2454 s, 59.2 MB/s We can see that the read performance is very very bad (59MB/s compared to 135MB/s when using no encryption). Nothing is using the disks during benchmark. I can confirm this because I checked with iostat and dstat. Details on the hardware: disks: all are WD green, 5400rpm, 64mb cache. cpu: FX-8350 at stock speed ram: 4x4GB at 1066Mhz. Details on the software: OS: Debian Wheezy 7, amd64 mdadm: v3.2.5 - 18th May 2012 LVM version: 2.02.95(2) (2012-03-06) LVM Library version: 1.02.74 (2012-03-06) LVM Driver version: 4.22.0 cryptsetup: 1.4.3 Here is how I configured the slow raid1+crypt+lvm setup: parted /dev/sdc mklabel gpt type: ext4 start: 2048s end: -1 Now the raid, crypt and the lvm configuration: mdadm --create /dev/md1 --level=1 --raid-disks=2 missing /dev/sdc cryptsetup --cipher serpent-xts-plain luksFormat /dev/md1 cryptsetup luksOpen /dev/md1 md1_crypt vgcreate vg_sql /dev/mapper/md1_crypt lvcreate -l 100%VG vg_sql -n lv_sql mkfs.ext4 /dev/mapper/vg_sql-lv-sql mount /dev/mapper/vg_sql-lv_sql /sql So guys, can you help me identify the reason and fix it? It has to be something with the cryptsetup as there is no such read slowdown on the other setup (sda+sdb) where no encryption is present. But I have no idea what to do. Thanks!

    Read the article

  • MegaCli newly created disk doesn't appear under /dev/sdX

    - by Henry-Nicolas Tourneur
    After having successfully added 2 new disks in a new RAID virtual drive (background initialization done), I would have exepected it to appear under /dev/sdh but it's not there (so, unusable). The system is running a CentOS 5.2 64 bits, HAL and udev daemons are running, not records of any sdh apparition under the messsage log file or in dmesg, only MegaCli do see that virtual drive. Any idea ? Some data: [root@server ~]# ./MegaCli -LDInfo -LALL -a0 Adapter 0 -- Virtual Drive Information: Virtual Disk: 0 (target id: 0) Name: RAID Level: Primary-1, Secondary-0, RAID Level Qualifier-0 Size:139392MB State: Optimal Stripe Size: 64kB Number Of Drives:2 Span Depth:1 Default Cache Policy: WriteBack, ReadAheadNone, Direct, No Write Cache if Bad BBU Current Cache Policy: WriteBack, ReadAheadNone, Direct, No Write Cache if Bad BBU Access Policy: Read/Write Disk Cache Policy: Disk's Default Virtual Disk: 1 (target id: 1) Name: RAID Level: Primary-1, Secondary-0, RAID Level Qualifier-0 Size:285568MB State: Optimal Stripe Size: 64kB Number Of Drives:2 Span Depth:1 Default Cache Policy: WriteBack, ReadAheadNone, Direct, No Write Cache if Bad BBU Current Cache Policy: WriteBack, ReadAheadNone, Direct, No Write Cache if Bad BBU Access Policy: Read/Write Disk Cache Policy: Disk's Default [root@server ~]# ls -l /dev/disk/by-id/scsi-360* lrwxrwxrwx 1 root root 9 Nov 17 2010 /dev/disk/by-id/scsi-36001ec90f82fe100108ca0a704098d09 -> ../../sda lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36001ec90f82fe100108ca0a704098d09-part1 -> ../../sda1 lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36001ec90f82fe100108ca0a704098d09-part2 -> ../../sda2 lrwxrwxrwx 1 root root 9 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fe07e78f94940c0000a0ee -> ../../sdf lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fe07e78f94940c0000a0ee-part1 -> ../../sdf1 lrwxrwxrwx 1 root root 9 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fe972a3f91240a0000005f -> ../../sdb lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fe972a3f91240a0000005f-part1 -> ../../sdb1 lrwxrwxrwx 1 root root 9 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fea7e18f94640c000020ec -> ../../sde lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fea7e18f94640c000020ec-part1 -> ../../sde1 lrwxrwxrwx 1 root root 9 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0feb7da8f94340c0000203d -> ../../sdd lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0feb7da8f94340c0000203d-part1 -> ../../sdd1 lrwxrwxrwx 1 root root 9 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fed7d78f94040c000080b7 -> ../../sdc lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fed7d78f94040c000080b7-part1 -> ../../sdc1 lrwxrwxrwx 1 root root 9 Nov 17 2010 /dev/disk/by-id/scsi-36090a05830145e58e0b9c479000010a1 -> ../../sdg lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36090a05830145e58e0b9c479000010a1-part1 -> ../../sdg1

    Read the article

  • ZFS Recover from Faulted Pool State

    - by nickv2002
    I have a six disk ZFS raidz1 pool and had a recent failure requiring a disk replacement. No problem normally, but this time my server hardware died before I could do the replacement (but after and unrelated to the drive failure as far as I can tell). I was able to get another machine from a friend to rebuild the system, but in the process of moving my drives over I had to swap their cables around a bunch until I got the right configuration where the remaining 5 good disks were seen as online. This process seems to have generated some checksum errors for the pool/raidz. I have the 5 remaining drives set up now and a good drive installed and ready to take the place of the drive that died. However, since my pool state is FAULTED I'm unable to do the replacement. root@zfs:~# zpool replace tank 1298243857915644462 /dev/sdb cannot open 'tank': pool is unavailable Is there any way to recover from this error? I would think that having 5 of the 6 drives online would be enough to rebuild the right data, but that doesn't seem to be enough now. Here's the status log of my pool: root@zfs:~# zpool status tank pool: tank state: FAULTED status: One or more devices could not be used because the label is missing or invalid. There are insufficient replicas for the pool to continue functioning. action: Destroy and re-create the pool from a backup source. see: http://zfsonlinux.org/msg/ZFS-8000-5E scan: none requested config: NAME STATE READ WRITE CKSUM tank FAULTED 0 0 1 corrupted data raidz1-0 ONLINE 0 0 8 sdd ONLINE 0 0 0 sdf ONLINE 0 0 0 sdh ONLINE 0 0 0 1298243857915644462 UNAVAIL 0 0 0 was /dev/sdb1 sde ONLINE 0 0 0 sdg ONLINE 0 0 0 Update (10/31): I tried to export and re-import the array a few times over the past week and wasn't successful. First I tried: zpool import -f -R /tank -N -o readonly=on -F tank That produced this error immediately: cannot import 'tank': I/O error Destroy and re-create the pool from a backup source. I added the '-X' option to the above command to try to make it check the transaction log. I let that run for about 48 hours before giving up because it had completely locked up my machine (I was unable to log in locally or via the network). Now I'm trying a simple zpool import tank command and that seems to run for a while with no output. I'll leave it running overnight to see if it outputs anything.

    Read the article

  • The Linux powered LAN Gaming House

    - by sachinghalot
    LAN parties offer the enjoyment of head to head gaming in a real-life social environment. In general, they are experiencing decline thanks to the convenience of Internet gaming, but Kenton Varda is a man who takes his LAN gaming very seriously. His LAN gaming house is a fascinating project, and best of all, Linux plays a part in making it all work.Varda has done his own write ups (short, long), so I'm only going to give an overview here. The setup is a large house with 12 gaming stations and a single server computer.The client computers themselves are rack mounted in a server room, and they are linked to the gaming stations on the floor above via extension cables (HDMI for video and audio and USB for mouse and keyboard). Each client computer, built into a 3U rack mount case, is a well specced gaming rig in its own right, sporting an Intel Core i5 processor, 4GB of RAM and an Nvidia GeForce 560 along with a 60GB SSD drive.Originally, the client computers ran Ubuntu Linux rather than Windows and the games executed under WINE, but Varda had to abandon this scheme. As he explains on his site:"Amazingly, a majority of games worked fine, although many had minor bugs (e.g. flickering mouse cursor, minor rendering artifacts, etc.). Some games, however, did not work, or had bad bugs that made them annoying to play."Subsequently, the gaming computers have been moved onto a more conventional gaming choice, Windows 7. It's a shame that WINE couldn't be made to work, but I can sympathize as it's rare to find modern games that work perfectly and at full native speed. Another problem with WINE is that it tends to suffer from regressions, which is hardly surprising when considering the difficulty of constantly improving the emulation of the Windows API. Varda points out that he preferred working with Linux clients as they were easier to modify and came with less licensing baggage.Linux still runs the server and all of the tools used are open source software. The hardware here is a Intel Xeon E3-1230 with 4GB of RAM. The storage hanging off this machine is a bit more complex than the clients. In addition to the 60GB SSD, it also has 2x1TB drives and a 240GB SDD.When the clients were running Linux, they booted over PXE using a toolchain that will be familiar to anyone who has setup Linux network booting. DHCP pointed the clients to the server which then supplied PXELINUX using TFTP. When booted, file access was accomplished through network block device (NBD). This is a very easy to use system that allows you to serve the contents of a file as a block device over the network. The client computer runs a user mode device driver and the device can be mounted within the file system using the mount command.One snag with offering file access via NBD is that it's difficult to impose any security restrictions on different areas of the file system as the server only sees a single file. The advantage is perfomance as the client operating system simply sees a block device, and besides, these security issues aren't relevant in this setup.Unfortunately, Windows 7 can't use NBD, so, Varda had to switch to iSCSI (which works in both server and client mode under Linux). His network cards are not compliant with this standard when doing a netboot, but fortunately, gPXE came to the rescue, and he boostraps it over PXE. gPXE is also available as an ISO image and is worth knowing about if you encounter an awkward machine that can't manage a network boot. It can also optionally boot from a HTTP server rather than the more traditional TFTP server.According to Varda, booting all 12 machines over the Gigabit Ethernet network is surprisingly fast, and once booted, the machines don't seem noticeably slower than if they were using local storage. Once loaded, most games attempt to load in as much data as possible, filling the RAM, and the the disk and network bandwidth required is small. It's worth noting that these are aspects of this project that might differ from some other thin client scenarios.At time of writing, it doesn't seem as though the local storage of the client machines is being utilized. Instead, the clients boot into Windows from an image on the server that contains the operating system and the games themselves. It uses the copy on write feature of LVM so that any writes from a client are added to a differencing image allocated to that client. As the administrator, Varda can log into the Linux server and authorize changes to the master image for updates etc.SummaryOverall, Varda estimates the total cost of the project at about $40,000, and of course, he needed a property that offered a large physical space in order to house the computers and the gaming workstations. Obviously, this project has stark differences to most thin client projects. The balance between storage, network usage, GPU power and security would not be typical of an office installation, for example. The only letdown is that WINE proved to be insufficiently compatible to run a wide variety of modern games, but that is, perhaps, asking too much of it, and hats off to Varda for trying to make it work.

    Read the article

  • ?Linux 6???UDEV??RAC ASM???????

    - by Liu Maclean(???)
    Maclean?????UDEV??ASMLIB?RAC???????????,???????????????????:Why ASMLIB and why not???UDEV????RAC ASM?????  ?«??UDEV????RAC ASM????? »???????????????,????????udev rule????: for i in b c d e f g h i j k ; do echo "KERNEL==\"sd*\", BUS==\"scsi\", PROGRAM==\"/sbin/scsi_id -g -u -s %p\", RESULT==\"`scsi_id -g -u -s /block/sd$i`\", NAME=\"asm-disk$i\", OWNER=\"grid\", GROUP=\"asmadmin\", MODE=\"0660\"" done ?????Linux 5?????, ????????redhat/Oracle Linux 6???????????? ????: ?OEL6??RHEL6?,????????? ??????:1. scsi_id??????????,scsi_id -g -u -s??????????2. udevtest???????,????udevadm??How to use udev for Oracle ASM in Oracle Linux 6   ???????????,???redhat/Oracle Linux 6??????udev rule ????: 1. #????? Linux 6.0???? [root@vrh6 dev]# cat /etc/issue Oracle Linux Server release 6.2 Kernel \r on an \m 2. #?????/etc/scsi_id.config echo "options=--whitelisted --replace-whitespace" >> /etc/scsi_id.config 3. #?????????udev?? [root@vrh6 dev]# ls -l sd* brw-rw----. 1 root disk 8, 0 Jun 30 09:29 sda brw-rw----. 1 root disk 8, 1 Jun 30 09:29 sda1 brw-rw----. 1 root disk 8, 2 Jun 30 09:29 sda2 brw-rw----. 1 root disk 8, 16 Jun 30 09:29 sdb brw-rw----. 1 root disk 8, 32 Jun 30 09:29 sdc brw-rw----. 1 root disk 8, 48 Jun 30 09:29 sdd brw-rw----. 1 root disk 8, 64 Jun 30 09:29 sde brw-rw----. 1 root disk 8, 80 Jun 30 09:29 sdf ??????? sdb-> sdf???????? 4. ? b->f?????for ???,??: # AUTO UDEV RULE BY Maclean Liu 2012/06/30 for i in b c d e f ; do echo "KERNEL==\"sd*\", BUS==\"scsi\", PROGRAM==\"/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/\$name\", RESULT==\"`/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/sd$i`\", NAME=\"asm-disk$i\", OWNER=\"grid\", GROUP=\"asmadmin\", MODE=\"0660\"" done ????sdb->sdf ?????RULE,????RULE???/etc/udev/rules.d/99-oracle-asmdevices.rules? ??????????? ,??RULE?99-oracle-asmdevices.rules # AUTO UDEV RULE BY Maclean Liu 2012/06/30 for i in b c d e f ; do echo "KERNEL==\"sd*\", BUS==\"scsi\", PROGRAM==\"/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/\$name\", RESULT==\"`/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/sd$i`\", NAME=\"asm-disk$i\", OWNER=\"grid\", GROUP=\"asmadmin\", MODE=\"0660\"" >> /etc/udev/rules.d/99-oracle-asmdevices.rules done 5. ?????root??/sbin/start_udev ?? ??????: [root@vrh6 dev]# echo "options=--whitelisted --replace-whitespace" >> /etc/scsi_id.config [root@vrh6 dev]# for i in b c d e f ; > do > echo "KERNEL==\"sd*\", BUS==\"scsi\", PROGRAM==\"/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/\$name\", RESULT==\"`/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/sd$i`\", NAME=\"asm-disk$i\", OWNER=\"grid\", GROUP=\"asmadmin\", MODE=\"0660\"" >> /etc/udev/rules.d/99-oracle-asmdevices.rules > done [root@vrh6 dev]# [root@vrh6 dev]# cat /etc/udev/rules.d/99-oracle-asmdevices.rules KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/$name", RESULT=="1ATA_VBOX_HARDDISK_VB09cadb31-cfbea255", NAME="asm-diskb", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/$name", RESULT=="1ATA_VBOX_HARDDISK_VB5f097069-59efb82f", NAME="asm-diskc", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/$name", RESULT=="1ATA_VBOX_HARDDISK_VB4e1a81c0-20478bc4", NAME="asm-diskd", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/$name", RESULT=="1ATA_VBOX_HARDDISK_VBdcce9285-b13c5a27", NAME="asm-diske", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/$name", RESULT=="1ATA_VBOX_HARDDISK_VB82effe1a-dbca7dff", NAME="asm-diskf", OWNER="grid", GROUP="asmadmin", MODE="0660" [root@vrh6 dev]# [root@vrh6 dev]# /sbin/start_udev Starting udev: [ OK ] [root@vrh6 dev]# ls -l asm* brw-rw----. 1 grid asmadmin 8, 16 Jun 30 09:34 asm-diskb brw-rw----. 1 grid asmadmin 8, 32 Jun 30 09:34 asm-diskc brw-rw----. 1 grid asmadmin 8, 48 Jun 30 09:34 asm-diskd brw-rw----. 1 grid asmadmin 8, 64 Jun 30 09:34 asm-diske brw-rw----. 1 grid asmadmin 8, 80 Jun 30 09:34 asm-diskf

    Read the article

  • Upgraded Ubuntu, all drives in one zpool marked unavailable

    - by Matt Sieker
    I just upgraded Ubuntu 14.04, and I had two ZFS pools on the server. There was some minor issue with me fighting with the ZFS driver and the kernel version, but that's worked out now. One pool came online, and mounted fine. The other didn't. The main difference between the tool is one was just a pool of disks (video/music storage), and the other was a raidz set (documents, etc) I've already attempted exporting and re-importing the pool, to no avail, attempting to import gets me this: root@kyou:/home/matt# zpool import -fFX -d /dev/disk/by-id/ pool: storage id: 15855792916570596778 state: UNAVAIL status: One or more devices contains corrupted data. action: The pool cannot be imported due to damaged devices or data. see: http://zfsonlinux.org/msg/ZFS-8000-5E config: storage UNAVAIL insufficient replicas raidz1-0 UNAVAIL insufficient replicas ata-SAMSUNG_HD103SJ_S246J90B134910 UNAVAIL ata-WDC_WD10EARS-00Y5B1_WD-WMAV51422523 UNAVAIL ata-WDC_WD10EARS-00Y5B1_WD-WMAV51535969 UNAVAIL The symlinks for those in /dev/disk/by-id also exist: root@kyou:/home/matt# ls -l /dev/disk/by-id/ata-SAMSUNG_HD103SJ_S246J90B134910* /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51* lrwxrwxrwx 1 root root 9 May 27 19:31 /dev/disk/by-id/ata-SAMSUNG_HD103SJ_S246J90B134910 -> ../../sdb lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-SAMSUNG_HD103SJ_S246J90B134910-part1 -> ../../sdb1 lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-SAMSUNG_HD103SJ_S246J90B134910-part9 -> ../../sdb9 lrwxrwxrwx 1 root root 9 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51422523 -> ../../sdd lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51422523-part1 -> ../../sdd1 lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51422523-part9 -> ../../sdd9 lrwxrwxrwx 1 root root 9 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51535969 -> ../../sde lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51535969-part1 -> ../../sde1 lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51535969-part9 -> ../../sde9 Inspecting the various /dev/sd* devices listed, they appear to be the correct ones (The 3 1TB drives that were in a raidz array). I've run zdb -l on each drive, dumping it to a file, and running a diff. The only difference on the 3 are the guid fields (Which I assume is expected). All 3 labels on each one are basically identical, and are as follows: version: 5000 name: 'storage' state: 0 txg: 4 pool_guid: 15855792916570596778 hostname: 'kyou' top_guid: 1683909657511667860 guid: 8815283814047599968 vdev_children: 1 vdev_tree: type: 'raidz' id: 0 guid: 1683909657511667860 nparity: 1 metaslab_array: 33 metaslab_shift: 34 ashift: 9 asize: 3000569954304 is_log: 0 create_txg: 4 children[0]: type: 'disk' id: 0 guid: 8815283814047599968 path: '/dev/disk/by-id/ata-SAMSUNG_HD103SJ_S246J90B134910-part1' whole_disk: 1 create_txg: 4 children[1]: type: 'disk' id: 1 guid: 18036424618735999728 path: '/dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51422523-part1' whole_disk: 1 create_txg: 4 children[2]: type: 'disk' id: 2 guid: 10307555127976192266 path: '/dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51535969-part1' whole_disk: 1 create_txg: 4 features_for_read: Stupidly, I do not have a recent backup of this pool. However, the pool was fine before reboot, and Linux sees the disks fine (I have smartctl running now to double check) So, in summary: I upgraded Ubuntu, and lost access to one of my two zpools. The difference between the pools is the one that came up was JBOD, the other was zraid. All drives in the unmountable zpool are marked UNAVAIL, with no notes for corrupted data The pools were both created with disks referenced from /dev/disk/by-id/. Symlinks from /dev/disk/by-id to the various /dev/sd devices seems to be correct zdb can read the labels from the drives. Pool has already been attempted to be exported/imported, and isn't able to import again. Is there some sort of black magic I can invoke via zpool/zfs to bring these disks back into a reasonable array? Can I run zpool create zraid ... without losing my data? Is my data gone anyhow?

    Read the article

  • Windows 7: How to place SuperFetch cache on an SSD?

    - by Ian Boyd
    I'm thinking of adding a solid state drive (SSD) to my existing Windows 7 installation. I know I can (and should) move my paging file to the SSD: Should the pagefile be placed on SSDs? Yes. Most pagefile operations are small random reads or larger sequential writes, both of which are types of operations that SSDs handle well. In looking at telemetry data from thousands of traces and focusing on pagefile reads and writes, we find that Pagefile.sys reads outnumber pagefile.sys writes by about 40 to 1, Pagefile.sys read sizes are typically quite small, with 67% less than or equal to 4 KB, and 88% less than 16 KB. Pagefile.sys writes are relatively large, with 62% greater than or equal to 128 KB and 45% being exactly 1 MB in size. In fact, given typical pagefile reference patterns and the favorable performance characteristics SSDs have on those patterns, there are few files better than the pagefile to place on an SSD. What I don't know is if I even can put a SuperFetch cache (i.e. ReadyBoost cache) on the solid state drive. I want to get the benefit of Windows being able to cache gigabytes of frequently accessed data on a relativly small (e.g. 30GB) solid state drive. This is exactly what SuperFetch+ReadyBoost (or SuperFetch+ReadyDrive) was designed for. Will Windows offer (or let) me place a ReadyBoost cache on a solid state flash drive connected via SATA? A problem with the ReadyBoost cache over the ReadyDrive cache is that the ReadyBoost cache does not survive between reboots. The cache is encrypted with a per-session key, making its existing contents unusable during boot and SuperFetch pre-fetching during login. Update One I know that Windows Vista limited you to only one ReadyBoost.sfcache file (I do not know if Windows 7 removed that limitation): Q: Can use use multiple devices for EMDs? A: Nope. We've limited Vista to one ReadyBoost per machine Q: Why just one device? A: Time and quality. Since this is the first revision of the feature, we decided to focus on making the single device exceptional, without the difficulties of managing multiple caches. We like the idea, though, and it's under consideration for future versions. I also know that the 4GB limit on the cache file was a limitation of the FAT filesystem used on most USB sticks - an SSD drive would be formatted with NTFS: Q: What's the largest amount of flash that I can use for ReadyBoost? A: You can use up to 4GB of flash for ReadyBoost (which turns out to be 8GB of cache w/ the compression) Q: Why can't I use more than 4GB of flash? A: The FAT32 filesystem limits our ReadyBoost.sfcache file to 4GB Can a ReadyBoost cache on an NTFS volume be larger than 4GB? Update Two The ReadyBoost cache is encrypted with a per-boot session key. This means that the cache has to be re-built after each boot, and cannot be used to help speed boot times, or latency from login to usable. Windows ReadyDrive technology takes advantage of non-volatile (NV) memory (i.e. flash) that is incorporated with some hybrid hard drives. This flash cache can be used to help Windows boot, or resume from hibernate faster. Will Windows 7 use an internal SSD drive as a ReadyBoost/*ReadyDrive*/SuperFetch cache? Is it possible to make Windows store a SuperFetch cache (i.e. ReadyBoost) on a non-removable SSD? Is it possible to not encrypt the ReadyBoost cache, and if so will Windows 7 use the cache at boot time? See also SuperUser.com: ReadyBoost + SSD = ? Windows 7 - ReadyBoost & SSD drives? Support and Q&A for Solid-State Drives Using SDD as a cache for HDD, is there a solution? Performance increase using SSD for paging/fetch/cache or ReadyBoost? (Win7) Windows 7 To Boost SSD Performance How to Disable Nonvolatile Caching

    Read the article

  • Performance issues when using SSD for a developer notebook (WAMP/LAMP stack)?

    - by András Szepesházi
    I'm a web application developer using my notebook as a standalone development environment (WAMP stack). I just switched from a Core2-duo Vista 32 bit notebook with 2Gb RAM and SATA HDD, to an i5-2520M Win7 64 bit with 4Gb RAM and 128 GB SDD (Corsair P3 128). My initial experience was what I expected, fast boot, quick load of all the applications (Eclipse takes now 5 seconds as opposed to 30s on my old notebook), overall great experience. Then I started to build up my development stack, both as LAMP (using VirtualBox with a debian guest) and WAMP (windows native apache + mysql + php). I wanted to compare those two. This still all worked great out, then I started to pull in my projects to these stacks. And here came the nasty surprise, one of those projects produced a lot worse response times than on my old notebook (that was true for both the VirtualBox and WAMP stack). Apache, php and mysql configurations were practically identical in all environments. I started to do a lot of benchmarking and profiling, and here is what I've found: All general benchmarks (Performance Test 7.0, HDTune Pro, wPrime2 and some more) gave a big advantage to the new notebook. Nothing surprising here. Disc specific tests showed that read/write operations peaked around 380M/160M for the SSD, and all the different sized block operations also performed very well. Started apache performance benchmarking with Apache Benchmark for a small static html file (10 concurrent threads, 500 iterations). Old notebook: min 47ms, median 111ms, max 156ms New WAMP stack: min 71ms, median 135ms, max 296ms New LAMP stack (in VirtualBox): min 6ms, median 46ms, max 175ms Right here I don't get why the native WAMP stack performed so bad, but at least the LAMP environment brought the expected speed. Apache performance measurement for non-cached php content. The php runs a loop of 1000 and generates sha1(uniqid()) inisde. Again, 10 concurrent threads, 500 iterations were used for the benchmark. Old notebook: min 0ms, median 39ms, max 218ms New WAMP stack: min 20ms, median 61ms, max 186ms New LAMP stack (in VirtualBox): min 124ms, median 704ms, max 2463ms What the hell? The new LAMP performed miserably, and even the new native WAMP was outperformed by the old notebook. php + mysql test. The test consists of connecting to a database and reading a single record form a table using INNER JOIN on 3 more (indexed) tables, repeated 100 times within a loop. Databases were identical. 10 concurrent threads, 100 iterations were used for the benchmark. Old notebook: min 1201ms, median 1734ms, max 3728ms New WAMP stack: min 367ms, median 675ms, max 1893ms New LAMP stack (in VirtualBox): min 1410ms, median 3659ms, max 5045ms And the same test with concurrency set to 1 (instead of 10): Old notebook: min 1201ms, median 1261ms, max 1357ms New WAMP stack: min 399ms, median 483ms, max 539ms New LAMP stack (in VirtualBox): min 285ms, median 348ms, max 444ms Strictly for my purposes, as I'm using a self contained development environment (= low concurrency) I could be satisfied with the second test's result. Though I have no idea why the VirtualBox environment performed so bad with higher concurrency. Finally I performed a test of including many php files. The application that I mentioned at the beginning, the one that was performing so bad, has a heavy bootstrap, loads hundreds of small library and configuration files while initializing. So this test does nothing else just includes about 100 files. Concurrency set to 1, 100 iterations: Old notebook: min 140ms, median 168ms, max 406ms New WAMP stack: min 434ms, median 488ms, max 604ms New LAMP stack (in VirtualBox): min 413ms, median 1040ms, max 1921ms Even if I consider that VirtualBox reached those files via shared folders, and that slows things down a bit, I still don't see how could the old notebook outperform so heavily both new configurations. And I think this is the real root of the slow performance, as the application uses even more includes, and the whole bootstrap will occur several times within a page request (for each ajax call, for example). To sum it up, here I am with a brand new high-performance notebook that loads the same page in 20 seconds, that my old notebook can do in 5-7 seconds. Needless to say, I'm not a very happy person right now. Why do you think I experience these poor performance values? What are my options to remedy this situation?

    Read the article

  • How to place SuperFetch cache on an SSD?

    - by Ian Boyd
    I'm thinking of adding a solid state drive (SSD) to my existing Windows 7 installation. I know I can (and should) move my paging file to the SSD: Should the pagefile be placed on SSDs? Yes. Most pagefile operations are small random reads or larger sequential writes, both of which are types of operations that SSDs handle well. In looking at telemetry data from thousands of traces and focusing on pagefile reads and writes, we find that Pagefile.sys reads outnumber pagefile.sys writes by about 40 to 1, Pagefile.sys read sizes are typically quite small, with 67% less than or equal to 4 KB, and 88% less than 16 KB. Pagefile.sys writes are relatively large, with 62% greater than or equal to 128 KB and 45% being exactly 1 MB in size. In fact, given typical pagefile reference patterns and the favorable performance characteristics SSDs have on those patterns, there are few files better than the pagefile to place on an SSD. What I don't know is if I even can put a SuperFetch cache (i.e. ReadyBoost cache) on the solid state drive. I want to get the benefit of Windows being able to cache gigabytes of frequently accessed data on a relativly small (e.g. 30GB) solid state drive. This is exactly what SuperFetch+ReadyBoost (or SuperFetch+ReadyDrive) was designed for. Will Windows offer (or let) me place a ReadyBoost cache on a solid state flash drive connected via SATA? A problem with the ReadyBoost cache over the ReadyDrive cache is that the ReadyBoost cache does not survive between reboots. The cache is encrypted with a per-session key, making its existing contents unusable during boot and SuperFetch pre-fetching during login. Update One I know that Windows Vista limited you to only one ReadyBoost.sfcache file (I do not know if Windows 7 removed that limitation): Q: Can use use multiple devices for EMDs? A: Nope. We've limited Vista to one ReadyBoost per machine Q: Why just one device? A: Time and quality. Since this is the first revision of the feature, we decided to focus on making the single device exceptional, without the difficulties of managing multiple caches. We like the idea, though, and it's under consideration for future versions. I also know that the 4GB limit on the cache file was a limitation of the FAT filesystem used on most USB sticks - an SSD drive would be formatted with NTFS: Q: What's the largest amount of flash that I can use for ReadyBoost? A: You can use up to 4GB of flash for ReadyBoost (which turns out to be 8GB of cache w/ the compression) Q: Why can't I use more than 4GB of flash? A: The FAT32 filesystem limits our ReadyBoost.sfcache file to 4GB Can a ReadyBoost cache on an NTFS volume be larger than 4GB? Update Two The ReadyBoost cache is encrypted with a per-boot session key. This means that the cache has to be re-built after each boot, and cannot be used to help speed boot times, or latency from login to usable. Windows ReadyDrive technology takes advantage of non-volatile (NV) memory (i.e. flash) that is incorporated with some hybrid hard drives. This flash cache can be used to help Windows boot, or resume from hibernate faster. Will Windows 7 use an internal SSD drive as a ReadyBoost/*ReadyDrive*/SuperFetch cache? Is it possible to make Windows store a SuperFetch cache (i.e. ReadyBoost) on a non-removable SSD? Is it possible to not encrypt the ReadyBoost cache, and if so will Windows 7 use the cache at boot time? See also SuperUser.com: ReadyBoost + SSD = ? Windows 7 - ReadyBoost & SSD drives? Support and Q&A for Solid-State Drives Using SDD as a cache for HDD, is there a solution? Performance increase using SSD for paging/fetch/cache or ReadyBoost? (Win7) Windows 7 To Boost SSD Performance How to Disable Nonvolatile Caching

    Read the article

< Previous Page | 1 2 3 4 5 6  | Next Page >