Search Results

Search found 18580 results on 744 pages for 'wireless connection'.

Page 5/744 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• 12.04 drops Wired Network if Wireless connects

  - by mitt10tim

  This is a little different then most of the questions I have seen here. When I am at my office I keep my Lenovo Thinkpad t61p running Ubuntu 12.04 x64 connected via wired Ethernet. I also typically leave the wireless radios on. After a recent update the behavior of laptop in regards to the networks has changed. It used to be that if the laptop had a wired connection, the wired would supersede the wireless. Now, when I get to work and plug the laptop in and power it up, it connects via wired (correct behavior), shortly after the wireless begins searching for its favorite network (also correct) but as soon as it finds a network to connect to, I lose Internet. If I disconnect from the wireless network, leaving the wireless radios powered on, and refresh the wired connection, all is well again. Powering down the wireless radios also corrects the problem. How can I set this up so that the wired network (if available) always has precedence over the wireless?

  Read the article

• Internet access using Edimax BR-6204WG as NIC

  - by Mat Richardson

  My internet access at home is provided by Virgin Media via their superhub. I have a laptop with no NIC - however I do have a spare wireless router, the Edimax BR-6204WG, which I have been led to believe can be used to bridge wireless connections. Only problem is, I'm not sure how to go about doing this. The manual for the device is here:- http://www.edimax.co.uk/images/Image/manual/Wireless/BR-6204Wg/BR-6204Wg_Manual.pdf Basically, I want to be able to connect the Edimax wireless router to my laptop using ethernet cable and to use it to pick up the wireless connection from my Virgin superhub. I've managed to get so far in some ways, but then I'm stuck.

  Read the article

• What is causing my internet to be slow on one laptop but not the other and only at a distance?

  - by Matt Case

  I have a newer laptop, purchased within the last year (acer aspire 7740). This laptop does not have any problem connecting to wireless networks and indicates that the signal strength is excellent on most of the wireless networks I connect to. When the laptop is within 10 feet of my wireless router it gets 30 down 10 up. When it is farther away than 10 feet it will be lucky to get 3 down and 1 up. I also have an older laptop, purchased in 2005, that has no problems at all at the same range. None of my phones, gaming consoles or tablets have this problem. I am beginning to think that the problem must be some hardware defect with the wireless card. I can provide additional information if needed. Just thought I'd check to see what others thought because I've been working on computers my whole life and have never heard of this happening. I have also tried to change the channels on my wireless router and have had no success with this idea.

  Read the article

• How to configure a wireless router to point to a remote www proxy

  - by Mark

  I have a LG smart Tv with browser. I need the tv browser to connect to a uk based proxy server on port 808. Unfortunately there is no option within tv to setup proxy for its browser. Now the Tv connects via a wireless connection to the internet. IE: TV <- D-Link DIR-605L <- ADSL <- WWW. Is it possible to setup this wireless router to connect the TV to the Proxy ?? If so ? where ? and what setings do i need to change in the wireless router ?? In short my question is ? How do i get the wireless router to make up for the lack of proxy connectivity within my Tv browser ?? Thanks in advance NB: I have configured my Pc's browser's proxy settings, and streaming via the proxy works 100%

  Read the article

• How do I get a Wireless N PCi card to connect to a wireless G router?

  - by Andy

  I'm having some problems setting up a new wireless PCI card on a WinXP SP3 PC. I know that the router is configured correctly. It is a Linksys WRT54GL, using 802.11b/g. Security mode is WPA2 Personal with TKIP+AES encryption. I am able to connect to this fine using my laptop (first gen MacBook with a 802.11b built in card). The new PCI card is also Linksys, but it supports 802.11n. Card seems to be installed ok (Windows sees it fine, doesn't list any errors in Device Manager), however when it scans for available wireless networks it can't find my wireless network (the router is set to broadcast the SSID). I tried to enter the network SSID manually, but that didn't seem to help. I chose WPA2-PSK for network authentication. The only options for encryption are TKIP or AES - I've tried both, neither worked. I am sure that I typed in my wireless key correctly. At this point, I don't think the problem is with encryption, but something else. It almost seems like I need to switch the wireless card into g mode, but I haven't found a way to do that (if that is even possible/necessary - I thought n was fully backwards compatible with g). Also, the PC is in the same room as the router, and my laptop, so I don't think that it is an interference issue. Any ideas what I'm doing wrong? I'm running out of things to try at this point. :(

  Read the article

• Wireless Repeating with two Netgear N750 (WNDR4300)

  - by jomo1911

  I have a Netgear N750 as my main router, which connects to the internet via a modem. I have a second Netgear N750 which I want to use to repeat the wireless signal of the main router. I logged in to routerlogin of my main router (192.168.1.1) and set up the "Wireless Repeating Function". I set it as the "Wireless Base Station" and filled in the MAC adress of my second Netgear N750. Then I logged in to routerlogin of my second router and set it up as the "Wireless Repeater", I gave it the IP 192.168.1.11 and filled in the MAC adress of the base station. During the setup of the second router (Repeater) I had to disable all security functions. If I connect to the repeaters' WLAN signal, I get no internet connection. Maybe you can help me, thanks

  Read the article

• Wireless Network Disappearing From Available Networks (Windows 7)

  - by PeteDaMeat

  I have been using Windows 7 with a BT Voyager wireless adapter to connect to my home wireless network for around the last 6 months or so and until recently have experienced no problems. However, over the last couple of days Windows has been unable to connect to the network and the network name is no longer visible in the list of available wireless networks. The only way I have got round the problem is to reboot the NetGear router and to change the SSID to a network name which has not already been used. I do not believe the problem is with the router as my mobile phone can connect to it without any problems. The BT Voyager wireless adapter detects all other available networks so I presume this is a Windows 7 issue as it seems to occur when the PC is rebooted. This problen has happened twice in the last 2 days and is becoming extremely annoying. Does anyone have any suggestions?

  Read the article

• Wireless Connection unstable when multiple devices connected

  - by KingIsulgard

  My wireless network works perfectly when only 1 device is connected. Super fast, full strength. But as soon as multiple devices are connected to the wireless network the connections become unstable (constantly losing connection). It's quite annoying. I have a Sitecom Wireless 300N XR Gigabit Router WL-306, which should be a decent router so I'm guessing there must be something wrong with my configuration. Does any of you know what might cause this? Thanks

  Read the article

• Wireless is disabled by hardware switch on Dell Inspiron 1750

  - by lowerkey

  I have a problem where Ubuntu (12.04) says there is a wireless network card, but it is disabled by a hardware switch. How do I turn it on? I checked the BIOS, and the wireless card is enabled there. Fn + F2 was also no success. The results of rfkill list: 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes sudo rfkill unblock wifi did nothing to the Wireless Status.

  Read the article

• Wireless broken after latest 12.04 update

  - by inderpaldeol

  I updated 12.04 yesterday and it broke my wireless connection. iwconfig lo no wireless extensions. eth0 no wireless extensions. l@ubuntu:~$ lspci|grep Network 03:00.0 Network controller: Ralink corp. RT3090 Wireless 802.11n 1T/1R PCIe In the hardware drivers, I see - rt3090sta is activated but currently not in use. WICD does not show wireless networks. Can someone help me please? Thanks id

  Read the article

• WIFI looses connection with AR9285 - have to disconnect / connect to regain internet?

  - by CodyLoco

  I have a G73JW laptop using Ubuntu 12.04. It has an Atheros AR9285 card. While wifi seems to work fine most of the time, about every hour or two it will loose the connection to the internet. The connection will appear to be connected still to the wireless router, but internet access is gone. Disconnecting and reconnecting to the access point solves the problem, as does disabling and reenabling the adapter via the hardware keyboard shortcut. How might this be solved so the connection is stable and doesn't drop? EDIT: It looks like the network dropping isn't related to DNS as it fails either way: codyloco@CodyLoco-Ubuntu:~$ dig askubuntu.com @8.8.8.8 ; <<>> DiG 9.8.1-P1 <<>> askubuntu.com @8.8.8.8 ;; global options: +cmd ;; connection timed out; no servers could be reached codyloco@CodyLoco-Ubuntu:~$ dig askubuntu.com ; <<>> DiG 9.8.1-P1 <<>> askubuntu.com ;; global options: +cmd ;; connection timed out; no servers could be reached Again cycling (disabling / enabling) the adapter corrects the issue.

  Read the article

• Macbook Pro Wireless Reconnecting

  - by A Student at a University

  I'm using a WPA2 EAP network. I'm sitting next to the access point. The connection keeps dropping and taking ~10 seconds to reconnect. My other devices are staying online. What's causing it? syslog: 01:21:10 dhclient: DHCPREQUEST of XXX.XXX.XXX.XXX on eth1 to XXX.XXX.XXX.XXX port 67 01:21:10 dhclient: DHCPACK of XXX.XXX.XXX.XXX from XXX.XXX.XXX.XXX 01:21:10 NetworkManager[XX40]: <info> (eth1): DHCPv4 state changed reboot -> renew 01:21:10 NetworkManager[XX40]: <info> address XXX.XXX.XXX.XXX 01:21:10 NetworkManager[XX40]: <info> prefix 20 (XXX.XXX.XXX.XXX) 01:21:10 NetworkManager[XX40]: <info> gateway XXX.XXX.XXX.XXX 01:21:10 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:21:10 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:21:10 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:21:10 NetworkManager[XX40]: <info> domain name 'server.domain.tld' 01:21:10 dhclient: bound to XXX.XXX.XXX.XXX -- renewal in XXX seconds. 01:33:30 dhclient: DHCPREQUEST of XXX.XXX.XXX.XXX on eth1 to XXX.XXX.XXX.XXX port 67 01:33:30 dhclient: DHCPACK of XXX.XXX.XXX.XXX from XXX.XXX.XXX.XXX 01:33:30 dhclient: bound to XXX.XXX.XXX.XXX -- renewal in XXX seconds. 01:35:13 wpa_supplicant[XX60]: CTRL-EVENT-EAP-STARTED EAP authentication started 01:35:13 wpa_supplicant[XX60]: CTRL-EVENT-EAP-METHOD EAP vendor 0 method 25 (PEAP) selected 01:35:14 wpa_supplicant[XX60]: EAP-MSCHAPV2: Authentication succeeded 01:35:14 wpa_supplicant[XX60]: EAP-TLV: TLV Result - Success - EAP-TLV/Phase2 Completed 01:35:14 wpa_supplicant[XX60]: CTRL-EVENT-EAP-SUCCESS EAP authentication completed successfully 01:35:14 NetworkManager[XX40]: <info> (eth1): supplicant connection state: completed -> 4-way handshake 01:35:14 wpa_supplicant[XX60]: WPA: Key negotiation completed with XX:XX:XX:XX:XX:XX [PTK=CCMP GTK=TKIP] 01:35:14 NetworkManager[XX40]: <info> (eth1): supplicant connection state: 4-way handshake -> group handshake 01:35:14 NetworkManager[XX40]: <info> (eth1): supplicant connection state: group handshake -> completed 01:35:17 wpa_supplicant[XX60]: CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys 01:35:17 NetworkManager[XX40]: <info> (eth1): supplicant connection state: completed -> disconnected 01:35:17 NetworkManager[XX40]: <info> (eth1): supplicant connection state: disconnected -> scanning 01:35:26 wpa_supplicant[XX60]: CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys 01:35:26 NetworkManager[XX40]: <info> (eth1): supplicant connection state: scanning -> disconnected 01:35:29 NetworkManager[XX40]: <info> (eth1): supplicant connection state: disconnected -> scanning 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 8 -> 3 (reason 11) 01:35:32 NetworkManager[XX40]: <info> (eth1): deactivating device (reason: 11). 01:35:32 NetworkManager[XX40]: <info> (eth1): canceled DHCP transaction, DHCP client pid XX27 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) starting connection 'Auto XXXXXXXXXX' 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 3 -> 4 (reason 0) 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) scheduled... 01:35:32 NetworkManager[XX40]: <info> (eth1): supplicant connection state: scanning -> disconnected 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) started... 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) scheduled... 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) complete. 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) starting... 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 4 -> 5 (reason 0) 01:35:32 NetworkManager[XX40]: <info> Activation (eth1/wireless): access point 'Auto XXXXXXXXXX' has security, but secrets are required. 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 5 -> 6 (reason 0) 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) complete. 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) scheduled... 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) started... 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 6 -> 4 (reason 0) 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) scheduled... 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) complete. 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) starting... 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 4 -> 5 (reason 0) 01:35:32 NetworkManager[XX40]: <info> Activation (eth1/wireless): connection 'Auto XXXXXXXXXX' has security, and secrets exist. No new secrets needed. 01:35:32 NetworkManager[XX40]: <info> Config: added 'ssid' value 'XXXXXXXXXX' 01:35:32 NetworkManager[XX40]: <info> Config: added 'scan_ssid' value '1' 01:35:32 NetworkManager[XX40]: <info> Config: added 'key_mgmt' value 'WPA-EAP' 01:35:32 NetworkManager[XX40]: <info> Config: added 'password' value '<omitted>' 01:35:32 NetworkManager[XX40]: <info> Config: added 'eap' value 'PEAP' 01:35:32 NetworkManager[XX40]: <info> Config: added 'fragment_size' value 'XXX0' 01:35:32 NetworkManager[XX40]: <info> Config: added 'phase2' value 'auth=MSCHAPV2' 01:35:32 NetworkManager[XX40]: <info> Config: added 'ca_cert' value '/etc/ssl/certs/Equifax_Secure_CA.pem' 01:35:32 NetworkManager[XX40]: <info> Config: added 'identity' value 'XXXXXXX' 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) complete. 01:35:32 NetworkManager[XX40]: <info> Config: set interface ap_scan to 1 01:35:32 NetworkManager[XX40]: <info> (eth1): supplicant connection state: disconnected -> scanning 01:35:36 wpa_supplicant[XX60]: Associated with XX:XX:XX:XX:XX:XX 01:35:36 NetworkManager[XX40]: <info> (eth1): supplicant connection state: scanning -> associated 01:35:36 wpa_supplicant[XX60]: CTRL-EVENT-EAP-STARTED EAP authentication started 01:35:36 wpa_supplicant[XX60]: CTRL-EVENT-EAP-METHOD EAP vendor 0 method 25 (PEAP) selected 01:35:36 wpa_supplicant[XX60]: EAP-MSCHAPV2: Authentication succeeded 01:35:36 wpa_supplicant[XX60]: EAP-TLV: TLV Result - Success - EAP-TLV/Phase2 Completed 01:35:36 wpa_supplicant[XX60]: CTRL-EVENT-EAP-SUCCESS EAP authentication completed successfully 01:35:36 NetworkManager[XX40]: <info> (eth1): supplicant connection state: associated -> 4-way handshake 01:35:36 wpa_supplicant[XX60]: WPA: Could not find AP from the scan results 01:35:36 wpa_supplicant[XX60]: WPA: Key negotiation completed with XX:XX:XX:XX:XX:XX [PTK=CCMP GTK=TKIP] 01:35:36 wpa_supplicant[XX60]: CTRL-EVENT-CONNECTED - Connection to XX:XX:XX:XX:XX:XX completed (reauth) [id=0 id_str=] 01:35:36 NetworkManager[XX40]: <info> (eth1): supplicant connection state: 4-way handshake -> group handshake 01:35:36 NetworkManager[XX40]: <info> (eth1): supplicant connection state: group handshake -> completed 01:35:36 NetworkManager[XX40]: <info> Activation (eth1/wireless) Stage 2 of 5 (Device Configure) successful. Connected to wireless network 'XXXXXXXXXX'. 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 3 of 5 (IP Configure Start) scheduled. 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 3 of 5 (IP Configure Start) started... 01:35:36 NetworkManager[XX40]: <info> (eth1): device state change: 5 -> 7 (reason 0) 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Beginning DHCPv4 transaction (timeout in 45 seconds) 01:35:36 NetworkManager[XX40]: <info> dhclient started with pid XX87 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 3 of 5 (IP Configure Start) complete. 01:35:36 dhclient: Internet Systems Consortium DHCP Client VXXX.XXX.XXX 01:35:36 dhclient: Copyright 2004-2009 Internet Systems Consortium. 01:35:36 dhclient: All rights reserved. 01:35:36 dhclient: For info, please visit https://www.isc.org/software/dhcp/ 01:35:36 dhclient: 01:35:36 NetworkManager[XX40]: <info> (eth1): DHCPv4 state changed nbi -> preinit 01:35:36 dhclient: Listening on LPF/eth1/XX:XX:XX:XX:XX:XX 01:35:36 dhclient: Sending on LPF/eth1/XX:XX:XX:XX:XX:XX 01:35:36 dhclient: Sending on Socket/fallback 01:35:36 dhclient: DHCPREQUEST of XXX.XXX.XXX.XXX on eth1 to XXX.XXX.XXX.XXX port 67 01:35:36 dhclient: DHCPACK of XXX.XXX.XXX.XXX from XXX.XXX.XXX.XXX 01:35:36 dhclient: bound to XXX.XXX.XXX.XXX -- renewal in XXX seconds. 01:35:36 NetworkManager[XX40]: <info> (eth1): DHCPv4 state changed preinit -> reboot 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 4 of 5 (IP4 Configure Get) scheduled... 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 4 of 5 (IP4 Configure Get) started... 01:35:36 NetworkManager[XX40]: <info> address XXX.XXX.XXX.XXX 01:35:36 NetworkManager[XX40]: <info> prefix 20 (XXX.XXX.XXX.XXX) 01:35:36 NetworkManager[XX40]: <info> gateway XXX.XXX.XXX.XXX 01:35:36 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:35:36 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:35:36 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:35:36 NetworkManager[XX40]: <info> domain name 'server.domain.tld' 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 5 of 5 (IP Configure Commit) scheduled... 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 4 of 5 (IP4 Configure Get) complete. 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 5 of 5 (IP Configure Commit) started... 01:35:37 NetworkManager[XX40]: <info> (eth1): device state change: 7 -> 8 (reason 0) 01:35:37 NetworkManager[XX40]: <info> (eth1): roamed from BSSID XX:XX:XX:XX:XX:XX (XXXXXXXXXX) to XX:XX:XX:XX:XX:XX (XXXXXXXXX) 01:35:37 NetworkManager[XX40]: <info> Policy set 'Auto XXXXXXXXXX' (eth1) as default for IPv4 routing and DNS. 01:35:37 NetworkManager[XX40]: <info> Activation (eth1) successful, device activated. 01:35:37 NetworkManager[XX40]: <info> Activation (eth1) Stage 5 of 5 (IP Configure Commit) complete. 01:35:43 wpa_supplicant[XX60]: Trying to associate with XX:XX:XX:XX:XX:XX (SSID='XXXXXXXXXX' freq=2412 MHz) 01:35:43 NetworkManager[XX40]: <info> (eth1): supplicant connection state: completed -> associating 01:35:43 wpa_supplicant[XX60]: Association request to the driver failed 01:35:46 wpa_supplicant[XX60]: Associated with XX:XX:XX:XX:XX:XX 01:35:46 NetworkManager[XX40]: <info> (eth1): supplicant connection state: associating -> associated 01:35:46 NetworkManager[XX40]: <info> (eth1): supplicant connection state: associated -> 4-way handshake 01:35:46 wpa_supplicant[XX60]: WPA: Key negotiation completed with XX:XX:XX:XX:XX:XX [PTK=CCMP GTK=TKIP] 01:35:46 wpa_supplicant[XX60]: CTRL-EVENT-CONNECTED - Connection to XX:XX:XX:XX:XX:XX completed (reauth) [id=0 id_str=] 01:35:46 NetworkManager[XX40]: <info> (eth1): supplicant connection state: 4-way handshake -> group handshake 01:35:46 NetworkManager[XX40]: <info> (eth1): supplicant connection state: group handshake -> completed 01:40:47 wpa_supplicant[XX60]: WPA: Group rekeying completed with XX:XX:XX:XX:XX:XX [GTK=TKIP] 01:40:47 NetworkManager[XX40]: <info> (eth1): supplicant connection state: completed -> group handshake 01:40:47 NetworkManager[XX40]: <info> (eth1): supplicant connection state: group handshake -> completed 01:50:19 dhclient: DHCPREQUEST of XXX.XXX.XXX.XXX on eth1 to XXX.XXX.XXX.XXX port 67 01:50:19 dhclient: DHCPACK of XXX.XXX.XXX.XXX from XXX.XXX.XXX.XXX

  Read the article

• How do I create a WiFi hotspot sharing wireless internet connection (single adapter)?

  - by Ruppesh Nalwaya

  I know how to create a hotspot when connected to a wired network, but when I am using internet from a WiFi connection, this disconnects the wireless connection the moment I activate the hotspot. In Windows I can use Connectify Hotspot, which enables me to share the internet connection from the same wireless adapter as I am creating an access point on. As you can read on the technology overview page: Access Point mode allows you to create a hotspot using the same Wi-Fi card that you are using to access the Internet. How do I do this on Ubuntu?

  Read the article

• Fedora 12 Wireless problems (Intel Wireless 4965AGN Card)

  - by Ninefingers

  Hi All, I'm having an interesting experience with my wireless card at the moment. Basically, it does like this: I connect to the local wireless network (netgear router) It works, briefly, allowing me to browse a webpage or maybe two, if I'm lucky. It then stops working / sending any packets, whilst reported still connected. Now, me being me I've had a look to see what I can find. wpa_supplicant.log looks like this: Trying to associate with valid_mac:a2:30 (SSID='vennardwireless' freq=2462 MHz) Associated with valid_mac:a2:30 WPA: Key negotiation completed with valid_mac:a2:30 [PTK=CCMP GTK=TKIP] CTRL-EVENT-CONNECTED - Connection to valid_mac:a2:30 completed (reauth) [id=0 id_str=] CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys So that's working fine. dmesg | grep "*iwl*" spits out this: iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27kds iwlagn: Copyright(c) 2003-2009 Intel Corporation iwlagn 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 iwlagn 0000:03:00.0: setting latency timer to 64 iwlagn 0000:03:00.0: Detected Intel Wireless WiFi Link 4965AGN REV=0x4 iwlagn 0000:03:00.0: Tunable channels: 13 802.11bg, 19 802.11a channels iwlagn 0000:03:00.0: irq 32 for MSI/MSI-X phy0: Selected rate control algorithm 'iwl-agn-rs' iwlagn 0000:03:00.0: firmware: requesting iwlwifi-4965-2.ucode iwlagn 0000:03:00.0: loaded firmware version 228.61.2.24 Registered led device: iwl-phy0::radio Registered led device: iwl-phy0::assoc Registered led device: iwl-phy0::RX Registered led device: iwl-phy0::TX iwlagn 0000:03:00.0: iwl_tx_agg_start on ra = 00:24:b2:32:a3:30 tid = 0 iwlagn 0000:03:00.0: iwl_tx_agg_start on ra = 00:24:b2:32:a3:30 tid = 0 So that's working too. I can also ping 192.168.0.1 -I wlan0 and arping 192.168.0.1 -I wlan0 the router until the network falls over. uname -r:2.6.32.10-90.fc12.x86_64. Laptop is a Core2 Duo (2Ghz) with 3GB RAM. Other symptoms I've noticed are that wireshark freezes when I capture on the "broken" interface until I disconnect. Am using networkmanager as per normal. Stupidly, I can connect to the same router via eth0/a cat6 cable just fine. Everyone else can connect to the AP fine (from Windows). Yes, I'm sat right next to it and not trying to access a hotspot the other side of the world. Any ideas? Is this a broken update? (I intend to reboot and test an older kernel later)? Anyone else come across this? Edit: iwconfig wlan0 rate auto is the settings I'm using for rates. Also, according to networkmanager the network is still connected. Thanks for any pointers / advice.

  Read the article

• Wireless doesn't work on a Lenovo V570

  - by Stephen

  I've had Ubuntu installed on my HD for about 3 months but ever since I ran into this wireless issue I kinda lost my lust of Ubuntu. I have zero experience getting around with/ using the console command. I have a Lenovo V570. I got the driver update for the broadcom networking card via the Additional Drivers application but that did nothing. I love the look and feel of using Ubuntu but I have no technological experience for the matter. Any help would be awesome. When I scan for wireless connections while in Ubuntu, my computer picks up nothing, while on Win7 it will pick up the handful of wireless networks around my area. My wired connection is fine, but the use of not having wireless on a laptop is rather contradictory to it as a feature. Cheers! Also, I just installed 11.10, if that helps any. Yes, I used the search before I posted this, but again I have ZERO understanding of the command stuff and need a meat and potatoes answer(s). stephen@ubuntu:~$ sudo lshw -class network [sudo] password for stephen: *-network UNCLAIMED description: Network controller product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f1900000-f1903fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: 06 serial: f0:de:f1:63:98:14 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.1.78 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:f1804000-f1804fff memory:f1800000-f1803fff stephen@ubuntu:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: yes Hard blocked: no 1: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no

  Read the article

• Ubuntu 12.04 Freezes w/ Ethernet Unplugged + Wireless Drops (Acer Aspire 5516)

  - by Grand Master T

  Ubuntu 12.04-12.10 32/64 freezes or won't boot if the Ethernet cable is unplugged and will not hold a wireless connection. Here is my scenario... Laptop: Acer Aspire 5516 Wireless card: Broadcom BCM4312 Ubuntu 12.04 32/64 Issues Unity 3d won't load without the Ethernet cable plugged in. If I let it load with Ethernet plugged in, it will freeze once I disconnect the cable. Unity 2d will load without the Ethernet cable plugged. In Unity 2d, wireless cannot hold a connection. I can connect to a Wireless network, but when I try to use it (i.e. open a browser), it disconnects. I can reconnect by disabling wireless (uncheck Enable Wireless), re-enable wireless, and reconnect. But, it will disconnect again once I start using it. Ubuntu 12.10 Issues Since 12.10 only gives me the option to load 3d (I assume), I experience the same thing as the first issue in 12.04. Attempted Solutions Enable networking/LAN in BIOS Set LAN first in boot priority in BIOS Remove STA wireless driver (bcmwl-kernel-source) and install b43 low power driver (firmware-b43-lpphy-installer). Remove default Network Manager and install Wicd. So far, I have had no luck with fixing this issue. Does anyone have any further suggestions?

  Read the article

• Wireless problems with Broadcom BCM4313 with windows7 (duplicate)

  - by user292394

  I have wireless connection problem can't connect my wireless adress lspci -vvnn | grep 14e4 03:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter [14e4:4727] (rev 01) iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no lsmod Module Size Used by bnep 19624 2 rfcomm 69160 8 ip6t_REJECT 12939 1 xt_hl 12521 6 ip6t_rt 13537 3 nf_conntrack_ipv6 18894 8 nf_defrag_ipv6 34768 1 nf_conntrack_ipv6 ipt_REJECT 12541 1 xt_LOG 17717 10 xt_limit 12711 13 xt_tcpudp 12884 18 xt_addrtype 12635 4 nf_conntrack_ipv4 15012 8 nf_defrag_ipv4 12758 1 nf_conntrack_ipv4 xt_conntrack 12760 16 ip6table_filter 12815 1 ip6_tables 27025 1 ip6table_filter nf_conntrack_netbios_ns 12665 0 nf_conntrack_broadcast 12589 1 nf_conntrack_netbios_ns nf_nat_ftp 12770 0 nf_nat 21798 1 nf_nat_ftp nf_conntrack_ftp 18638 1 nf_nat_ftp nf_conntrack 96976 8 nf_nat_ftp,nf_conntrack_netbios_ns,nf_nat,xt_conntrack,nf_conntrack_broadcast,nf_conntrack_ftp,nf_conntrack_ipv4,nf_conntrack_ipv6 iptable_filter 12810 1 ip_tables 27239 1 iptable_filter vx_tables 34059 13 ip6table_filter,xt_hl,ip_tables,xt_tcpudp,xt_limit,xt_conntrack,xt_LOG,iptable_filter,ip6t_rt,ipt_REJECT,ip6_tables,xt_addrtype,ip6t_REJECT uvcvideo 80885 0 videobuf2_vmalloc 13216 1 uvcvideo videobuf2_memops 13362 1 videobuf2_vmalloc snd_hda_codec_hdmi 46207 1 videobuf2_core 40664 1 uvcvideo videodev 134688 2 uvcvideo,videobuf2_core snd_hda_codec_conexant 57441 1 snd_hda_intel 52355 8 snd_hda_codec 192906 3 snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_hda_intel snd_hwdep 13602 1 snd_hda_codec snd_pcm 102099 4 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel snd_page_alloc 18710 2 snd_pcm,snd_hda_intel snd_seq_midi 13324 0 dm_multipath 22873 0 snd_seq_midi_event 14899 1 snd_seq_midi scsi_dh 14882 1 dm_multipath lib80211_crypt_tkip 17619 0 snd_rawmidi 30144 1 snd_seq_midi intel_powerclamp 14705 0 coretemp 13435 0 kvm_intel 143060 0 kvm 451511 1 kvm_intel joydev 17381 0 serio_raw 13462 0 snd_seq 61560 2 snd_seq_midi_event,snd_seq_midi intel_ips 18664 0 wl 4207846 0 snd_seq_device 14497 3 snd_seq,snd_rawmidi,snd_seq_midi btusb 32412 0 bluetooth 395423 22 bnep,btusb,rfcomm snd_timer 29482 2 snd_pcm,snd_seq snd 69238 26 snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device,snd_seq_midi lib80211 14381 2 wl,lib80211_crypt_tkip toshiba_bluetooth 12852 0 cfg80211 484040 1 wl lpc_ich 21080 0 fglrx 8085343 190 soundcore 12680 1 snd toshiba_acpi 22901 0 sparse_keymap 13948 1 toshiba_acpi wmi 19177 1 toshiba_acpi amd_iommu_v2 19054 1 fglrx video 19476 0 mei_me 18627 0 mei 82276 1 mei_me mac_hid 13205 0 parport_pc 32701 0 ppdev 17671 0 lp 17759 0 parport 42348 3 lp,ppdev,parport_pc hid_generic 12548 0 usbhid 52570 0 hid 106148 2 hid_generic,usbhid psmouse 102222 0 ahci 25819 3 libahci 32168 1 ahci atl1c 46086 0 dm_mirror 22135 0 dm_region_hash 20862 1 dm_mirror dm_log 18411 2 dm_region_hash,dm_mirror Can someone give any ideas on how I can fix my wireless

  Read the article

• Connection Pooling vs Per-Thread JDBC Connection

  - by java_geek

  Which of these approaches is better ?

  Read the article

• Wireless doesn't work on a Broadcom BCM4312

  - by Boderick

  As stated, I've just upgraded to 12.04 and my Dell Inspiron 1545 isn't recognising its wireless card and I was wondering if anybody could help? Edit: Okay, so I found the wireless card by using lspci -vvv and it returned this: 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) Subsystem: Dell Wireless 1397 WLAN Mini-Card Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast TAbort- SERR- Kernel modules: ssb lsmod Module Size Used by dm_crypt 22528 0 joydev 17393 0 dell_wmi 12601 0 sparse_keymap 13658 1 dell_wmi dell_laptop 13671 0 dcdbas 14098 1 dell_laptop psmouse 72919 0 uvcvideo 67203 0 serio_raw 13027 0 videodev 86588 1 uvcvideo snd_hda_codec_idt 60251 1 mac_hid 13077 0 snd_hda_intel 32765 5 snd_hda_codec 109562 2 snd_hda_codec_idt,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec parport_pc 32114 0 rfcomm 38139 0 bnep 17830 2 ppdev 12849 0 snd_pcm 80845 3 snd_hda_intel,snd_hda_codec bluetooth 158438 10 rfcomm,bnep snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq binfmt_misc 17292 1 snd 62064 18 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm lp 17455 0 parport 40930 3 parport_pc,ppdev,lp sky2 53628 0 ums_realtek 17920 0 uas 17699 0 i915 414603 3 wmi 18744 1 dell_wmi drm_kms_helper 45466 1 i915 drm 197692 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 video 19068 1 i915 usb_storage 39646 1 ums_realtek ifconfig -a eth0 Link encap:Ethernet HWaddr 00:23:ae:24:71:45 inet addr:192.168.1.158 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::223:aeff:fe24:7145/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14340 errors:0 dropped:0 overruns:0 frame:0 TX packets:10191 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:15403754 (15.4 MB) TX bytes:1262570 (1.2 MB) Interrupt:18 ham0 Link encap:Ethernet HWaddr 7a:79:05:2d:b0:f7 inet addr:5.45.176.247 Bcast:5.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::7879:5ff:fe2d:b0f7/64 Scope:Link inet6 addr: 2620:9b::52d:b0f7/96 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1404 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:179 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:0 (0.0 B) TX bytes:27480 (27.4 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:433 errors:0 dropped:0 overruns:0 frame:0 TX packets:433 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:60051 (60.0 KB) TX bytes:60051 (60.0 KB) iwconfig lo no wireless extensions. ham0 no wireless extensions. eth0 no wireless extensions. the results for sudo lshw -class network *-network description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0c:00.0 logical name: eth1 version: 01 serial: 00:22:5f:77:1f:e6 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:17 memory:f69fc000-f69fffff *-network description: Ethernet interface product: 88E8040 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 13 serial: 00:23:ae:24:71:45 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full firmware=N/A ip=192.168.1.158 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:45 memory:f68fc000-f68fffff ioport:de00(size=256) *-network description: Ethernet interface physical id: 2 logical name: ham0 serial: 7a:79:05:2d:b0:f7 size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full firmware=N/A ip=5.45.176.247 link=yes multicast=yes port=twisted pair speed=10Mbit/s and the results of rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: yes Hard blocked: yes 1: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes

  Read the article

• Wireless Network Performance Issues

  - by colithium

  My brand new Dell XPS system has been running flawlessly except its abysmal download speeds. I have tried isolating every variable I could possibly think of but I can't figure out the problem. I've talked to Dell and Belkin without making progress (thought I'd try). Here are the speeds: Note that most of the time, upload speeds are actually much faster than download speeds (around 4.0 Mb/s which is better than most other devices on the network) It's not the ISP. The slowdown happens even when transferring files inside the network. Plus every other wireless device gets approximately this: It's not the wireless router. It's a Lynksis WRT160N v1 with the latest firmware (1.02.2). Plus everything else connected to it has normal speeds. It's not the browser. Speeds are the same in IE, FF, and when transferring files with Windows between computers. It's not the wireless adapter. I've tried a Belkin N Wireless USB Adapter (which works fine on another computer) and a Dell Wireless Draft 802.11n WLAN Mini-Card. They have the same slow speeds when connected to the problem computer. It's not the adapter connection. One adapter used USB and the other is a Mini-Card. It's not antenna placement. With the same antenna position and the same device, I get different speeds when connected to the problem computer vs a good computer. Plus everything reports the connection speed as at least 11Mbps and good signal strength. I've tried disabling IPv6 since it sometimes causes weird problems. I've tried disabling Windows Firewall/anti-virus. I've ensured the computer has updated drivers for both adapters. I've ensured that Windows is up to date and so is the BIOS. For the USB adapter I ensured that that USB port functioned at normal speeds with other USB devices. What else could it possibly be? I finally received my copy of Windows 7 and will be trying that. I'd rather not install Windows 7 because of a particular program that will stop working so a solution besides that is welcome. Specs: Vista x64 Core i7 920 6GB RAM 500GB HD GTX 260

  Read the article

• very slow internet with Linksys WRT54GL only in wireless mode (wired is OK)

  - by gojira

  I bought a new Cisco Linksys WRT54GL router to connect my laptop (running Windows 7) to the internet. I installed Tomato 1.28 firmware on the router. When I connect the laptop to the router via ethernet cable, everything is fine and I get extremely fast up- and download speeds. When I connect wirelesssly however, websites load extremely slow - it takes dozens of seconds to load a website! <-- This is my question, how can I fix the wireless speed issue? Gmail for example is unusable this way. I tried speedtest.net, but this always fails in the upload part of the test so I can't even test the bandwidth (could the fact that it fails in the upload part, not the download part, be an indication what the problem is?!). I have isolated the problem a bit, I am convinced it has to do either with the router itself, the router settings, or the settings of the wireless connection in Win 7. Because previously, I was using another router by Buffalo and I had no problems whatsoever. I have tried to reproduce the settings from the Bufallo router as closely as possible on the Linksys router (same channel, same encryption etc). The download speed problem only occurs with the Linksys router, and only in wireless mode! When I exchange the Linksys router with the Buffalo router I have here for testing, the wireless speed is up to normal again. Also, before I had installed the Tomato firmware I had exactly the same problem, so it has nothing to do with the firmware itself. Notes & things I already tried: Changing the channel: does not seem to affect anything, I am also on the same channel (10) which I was previously on when I had a Buffalo router. QoS is off. Ping to the router itself is OK, ~ 1 ms. Some current settings of the linksys router: WAN / Internet Type: DHCP Wirelesss Mode: Access Point B/G Mode: Mixed Broadcast: check Channel: 10 - 2.457 GHz Security: WPA2 Personal Encryption: AES

  Read the article

• Configuring two nearby WLANs: should I use the same ssid?

  - by Rory

  I'm configuring a home network for basic internet use (ie don't really need connectivity between workstations on the network). My brick walls mean a single wireless router doesn't provide good coverage throughout the house, so I have purchased two powerline adapters and now have the incoming modem/wireless router at one end of the house plugged into a powerline adapter, and at the other end of the house the other powerline adapter plugged into another wireless router. Currently the two wireless networks have different ssids. (The powerline adapters only do power-Ethernet; they're not wireless access points themselves.) This works well, except when I move between rooms and would ideally like my devices (iPad, phones, laptops) to switch from the weak to the strong signal. Sometimes there's enough signal that they hold on to the weak connects instead of switching to the strong one. Should I name the two networks the same ssid, and if so what is the actual effect? Do the signals get confused, is the bandwidth affected, will this help my devices seamlessly move from one to the other, or is the ssid just a cosmetic thing that actually doesn't have any impact on this situation? Are there any other settings that I should configure to make my setup optimal?

  Read the article

• Configuring home wireless network

  - by dvanaria

  I'm new to setting up a home wireless network. I have Comcast tv/internet/phone service (modem included) as well as a wireless router. My question is pretty basic. How can I tell the performance of the following parts of the network? 1. incoming internet speed 2. speed of the modem 3. speed of the wireless router I basically want as fast an internet connection as possible, of course, but I'm not sure where to look for the bottleneck (and so, not sure where I can spend some money to speed things up). Right now I'm getting about 36 Mbps (as it shows in Windows). If I run an online speed test (xfinity has one) it shows Average download speed of 14.91 Mbps and Average upload speed of 5.72 Mbps. Thanks for your help.

  Read the article

• Atheros AR9285 / Lenovo G560 wireless not working after installing 13.04

  - by teyi

  I had Ubuntu 12.04 initially installed on my laptop. I upgraded to 12.10 then 13.04. Everything worked fine, including wireless. After adding a new memory card ( I only had 2 gb and one memory slot free) my wireess stopped working. I backed up all my data and reinstallled Ubuntu 13.04. Everything works fine except wireess. I bought this laptop in 2010 from Japan. It has Intel Core i5 CPU M 450 @2.40 Ghz * 4 3,7 Gb RAM os type 64 bit The output of iwconfig: eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off The output of rfkill list all: 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no The output of lshw -C network: *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:05:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:7d:fe:fa width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.8.0-19-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:d6400000-d640ffff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: 02 serial: 88:ae:1d:2b:36:ac size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.2 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:d2410000-d2410fff memory:d2400000-d240ffff memory:d2420000-d243ffff The wi-fi network appears as disconnected ( it's greyed out) Strangely enough I see a wifi network ( not mine) but not mine or the rest. That network doesn't require a password . I click on it, try to connect and i get an error message: failed to connect to xxxxx ... 32) The access point/org/freedesktop/NetworkManager/AccessPoint/0 was not in the scan list. Someone help please

  Read the article

• wireless network with cable modem and access point

  - by hayri

  I have a Scientific Atlanta EPC2203 cable modem and a TP-Link TL-WA500G access point. When I connect my computer directly to modem with a CAT5e cable I have internet connection on my laptop (when i type ipconfig i see my external ip there, provided by isp). So I decided to have wireless network in the flat, allowing other devices to connect as well. I bought this wireless ap (TL-WA500G) configured Wireless security stuff, and connected it to my modem. With that configuration (by default AP has static ip of 192.168.1.254) only my computer can connect to internet over wifi, but not any other device. When I set the IP of AP to Dynamic IP (DHCP) it is the same. How should I change my configuration to enable all wifi devices to connect to internet?

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >