Search Results

Search found 18580 results on 744 pages for 'wireless connection'.

Page 6/744 | < Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >

• Wireless not working on Dell XPS 17 after installing 12.04

  - by user60622

  I (linux newbie) have a Dell XPS 17 and tried to install Ubuntu 12.04. After installation all WLAN accesspoints near are detected. But I can not connect (but I am able to connect with other computers as well as with Dell XPS 17 under windows). Outputs: iwconfig lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:"LerchenPoint" Mode:Managed Frequency:2.412 GHz Access Point: 58:6D:8F:A0:2D:58 Bit Rate=1 Mb/s Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-37 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:19 Missed beacon:0 eth0 no wireless extensions. sudo lshw -class network *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: 00:26:c7:99:98:28 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-24-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:50 memory:f0400000-f0401fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:0a:00.0 logical name: eth0 version: 06 serial: f0:4d:a2:56:e3:94 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.0.123 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:47 ioport:6000(size=256) memory:f0a04000-f0a04fff memory:f0a00000-f0a03fff dmesg | grep iwl [ 10.157531] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 10.157561] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 10.157598] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 10.157599] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90011090000 [ 10.157601] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 10.157731] iwlwifi 0000:04:00.0: irq 50 for MSI/MSI-X [ 10.157834] iwlwifi 0000:04:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 10.157976] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 10.179772] iwlwifi 0000:04:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 10.179775] iwlwifi 0000:04:00.0: Device SKU: 0X50 [ 10.179777] iwlwifi 0000:04:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 10.179796] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 10.574728] iwlwifi 0000:04:00.0: loaded firmware version 39.31.5.1 build 35138 [ 10.726409] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 19.714132] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 19.777862] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2251.603089] iwlwifi 0000:04:00.0: PCI INT A disabled [ 2266.578350] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 2266.578399] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 2266.578435] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 2266.578437] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90011090000 [ 2266.578439] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 2266.578704] iwlwifi 0000:04:00.0: irq 50 for MSI/MSI-X [ 2266.578808] iwlwifi 0000:04:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 2266.578916] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2266.600709] iwlwifi 0000:04:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 2266.600712] iwlwifi 0000:04:00.0: Device SKU: 0X50 [ 2266.600713] iwlwifi 0000:04:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 2266.600727] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 2266.605978] iwlwifi 0000:04:00.0: loaded firmware version 39.31.5.1 build 35138 [ 2266.606331] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 2266.614179] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2266.681541] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S Solutions I tried: rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf options iwlwifi 11n_disable=1 sudo modprobe -rfv iwlwifi WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release. rmmod /lib/modules/3.2.0-24-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko rmmod /lib/modules/3.2.0-24-generic/kernel/net/mac80211/mac80211.ko rmmod /lib/modules/3.2.0-24-generic/kernel/net/wireless/cfg80211.ko sudo modprobe iwlwifi WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release. replacing iwlwifi-1000-5.ucode (current driver) against iwlwifi-1000-3.ucode sudo jockey-gtk: (jockey-gtk:2493): Gtk-CRITICAL **: gtk_icon_set_render_icon_pixbuf: assertion icon_set != NULL' failed (jockey-gtk:2493): Gtk-CRITICAL **: gtk_icon_set_render_icon_pixbuf: assertion icon_set != NULL' failed nothing is listet in "Additional drivers" (german: "Zusätzliche Treiber"). gksudo gedit /etc/modprobe.d/blacklist.conf add "blacklist acer_wmi" Any help would be appreciated very much. Thanks!!

  Read the article

• windows 7 wireless knocks off other computers on the network

  - by Sean

  I am trying to fix a wireless network issue. When a new windows 7 machine (we have 2 in the house) we have problems with any other windows xp machines connecting to the wireless network. I am using a linksys WRT110 running Firmware Version: 1.0.04 (which is not the latest firmware its Ver.1.0.07 but the router would not use the bin update file). I have tried a ton of variations in setting for the wireless network, changed the channel, the security level (none, wep wpa, wpa2), network type (g,bg mixed). I have also read some stuff about homegroup settings for windows 7 but have not seen any differences that make a difference. Basically windows 7 does not like to connect to our network but when I manage to get it to work the windows xp pro machines get kicked off. The windows xp pro machines are a few years old but both windows 7 machines are less than 6 months old.

  Read the article

• My wireless is hard-blocked

  - by Cristian

  I'm new to linux and i am having trouble getting my wireless to work I've found the following things Wireless LAN Soft blocked: no Hard blocked: yes and : *-network DISABLED description: Wireless interface product: RT3090 Wireless 802.11n 1T/1R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 6c:62:6d:19:38:b9 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.2.0-25-generic-pae firmware=0.34 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:16 memory:fdfe0000-fdfefff Can you please tell me what to do?

  Read the article

• Suggestions for wireless adapter

  - by Michael Kniskern

  I recently purchased a desktop computer and it did not come with a wireless network card. I am currently using the Belkin Wireless G USB Adapter and it is a very sub par product. It has very slow response times and download speeds with just basic browsing and downloads podcasts through iTunes. Does anyone have a better suggestion for a wireless adapter? Should I go with another USB adapter or one that connects directly into the motherboard? I am current using Windows Vista 64 bit Home Premium.

  Read the article

• Wireless does not work anymore after software update with Ubuntu 12.10 on a Dell Latitude E6230

  - by Andy

  I just installed Ubuntu 12.10 on my DELL Latitude E6230, on first boot wifi worked properly but when I updated the software it stopped working. I can't figure out the problem... The wireless network controller is a Broadcom Corporation BCM4313 802.11b/g/n Wireless Lan Controller (rev 01) "lshw -class network" gives, for the above controller: *-network UNCLAIMED description: Network controller product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7d00000-f7d03fff After reading the answer to another similar question, I edited the file NetworkManager.conf to make "managed=true", but that did not make any difference, it is as if the wireless adapter were not there. In the "Network" setting window, I only see "Wired" and "Network proxy". Wireless has just disappeared: rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no and that's it! Nothing about the wireless controller... Any suggestions?

  Read the article

• Atheros AR5BWB222 Wireless Intermittent Connectivity

  - by Bart

  So I recently installed Ubuntu on my Acer Aspire V3-551 laptop. I have an Atheros AR5BWB222 wireless adapter. Everything works fine except for the wireless. I can sometimes connect to the wireless, but most of the time it will be making an attempt to connect and then enver connect. Or it will connect, but it will only stay connected for about 10 seconds before getting disconnected from the wireless. All the other drivers updated through System SettingsAdditional Drivers are fine, even the Ethernet. Its just the problem with the wireless. I've tried a power managment setting, tried looking for additional updates, but nothing fixes my problem. Is there any solution for my particular wireless card?

  Read the article

• Wireless problems on HP

  - by Sat93

  I'm not able to enable Wireless using the hardware switch on my HP ProBook4430s. Because of this the Enable Wireless option is greyd out and I cannot enable it. The greyd out option can be seen in the screenshot below. The results of iwconfig for my system are as follows, lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. Also I tried to do the following, sudo ifconfig wlan0 up but I got an error as below, SIOCSIFFLAGS: Operation not possible due to RF-kill Also the result of sudo rfkill list all for my system is as follows, 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no 2: hp-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 3: hci0: Bluetooth Soft blocked: no Hard blocked: no How do I fix this problem? Thanku!

  Read the article

• Programtically get the Wireless lan config of a machine and use netsh to setup new profile

  - by Maestro1024

  Programtically get the Wireless lan config of a machine and use netsh to setup new profile I am having trouble getting the netsh command to set the ssid of a new card. I installed the drivers and plugged it in. I see in ipconfig it says the "media is disconnected" (fair enough). I then send the following command netsh wlan connect name=profile1 ssid=myNetwork interface="Wireless Network Connection 2" problem is I get an error "There is no profile "profile1" assigned to the specified interface. What is a profile for a wireless card? What should I set it to? How Can I get my SSID set and connected for the card.

  Read the article

• D-Link DWA-125 Wireless network card not working after upgrade from 10.04 to 12.04

  - by dava2788

  I upgraded to Ubuntu 12.04 and now the wireless network card D-Link DWA-125 doesn't work. I have the drivers from the official website, But neither recognized during installation. iwconfig: lo no wireless extensions. vmnet8 no wireless extensions. ra0 Ralink STA Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. vmnet1 no wireless extensions. dava@Dava-Ubuntu:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 006: ID 07d1:3c0d D-Link System DWA-125 Wireless N 150 Adapter(rev.A1) [Ralink RT3070] And the chipset: ralink 2870/3070 (rt3070)

  Read the article

• Wireless Connection unstable with multiple devices connected

  - by KingIsulgard

  My wireless network works perfectly when only 1 device is connected. Super fast, full strength. But as soon as multiple devices are connected to the wireless network the connections become unstable (constantly losing connection with the internet, not the network itself). It's quite annoying. I have a Sitecom Wireless 300N XR Gigabit Router WL-306, which should be a decent router so I'm guessing there must be something wrong with my configuration. Does any of you know what might cause this? Thanks

  Read the article

• cannot connect to wireless network on ubuntu 12.04

  - by angjinhang

  i have installed ubuntu on my 6-year-old Acer Aspire 4310 and i love it's lightning speed.but, now i have a big problem, that is it cannot connect to any wireless network. the wireless network worked well in my windows. the wireless switch is not responding to me(i guess it only works on windows). there are also no wireless toggle switch on my keyboard. i have installed my driver, yeah, a proprietary driver. i installed it, and my i never see my wireless network anymore, even the enabling and disabling button in the system settings. i can connect my wireless network during the ubuntu installation. so what's the problem? i cannot find wlan0 in the ifconfig output. i can still see the enable and disable button in the system settings before i install the driver. now even i remove the driver, i will no longer display. i wanted my wifi back, help!

  Read the article

• No wireless adapter in msi u200

  - by Mino Marimat

  I have a MSi u200, and the weird thing was that I was using this normally before, then after a few minutes all of a sudden it couldn't find the wifi signal from my house. I did some troubleshooting and a bit of search in the control panel, and it seems like my hardware is missing. :( I can't even turn on the wireless light using Fn+F8, so my suspicions about the missing hardware strengthened. I tried searching for DIY fixes, but I found out that the wireless card is actually built-in deeper, unlike the RAM cards and the hard drive where you can either replace or add more cards. What do I do?? As of the moment, I can get connected to my wifi here at home using a wireless adapter via usb, and it's working. So my guess about the hardware problem seems correct. HELP!!! Thanks!

  Read the article

• Internet Connection Sharing, can't Share Wireless

  - by GuyNoir

  I'm using Windows XP, and I've been trying to setup my laptop so that I can connect to the internet connection that I get on the laptop through my mobile on an ad-hoc network. I've set up an ad-hoc network, but when I try to select "allow other users to connect through this computers internet connection", the only options I have are the Local Area Connections. The tutorial I've been using says that Wireless Connection should be in that pull down menu. Any help?

  Read the article

• forwarding packets from wireless nic wlan0 to another Wireless nic wlan1

  - by user179759

  I have two wireless interfaces wlan0, wlan1 I want wlan0 to be connected to the internet via a wireless router and I want wlan1 to be in AP mode acting as a router to give internet access to whoever connectes to it. So basically all packets coming through wlan1 should be forwarded to wlan0 = Router = Internet. That's including DNS/DHCP/etc.. [A]~~~~~(Wi-Fi)~~~~~~v [B]~~~~~(Wi-Fi)~~~> [me] ~~~~(Wi-Fi)~~~~~>[AP/Router]------->[internet] [C]~~~~~(Wi-Fi)~~~~~~^ Any idea how can I do this? ps: I tried using bridges but I always get 'operation not supported' using the brctl tool.

  Read the article

• Wireless Access Point - Can't ping other machines on the wireless network

  - by Surfer513

  I have a wireless access point (Netgear), and I have it setup so that it has an IP address in the current subnet (let's say 192.168.2.0, subnet mask of 255.255.255.0). The machine that it is connected to via ethernet cable has an IP in the same subnet as the AP. The machines that are connected to the AP via the wireless connection also have an IP address in the same subnet as the rest of the network (192.168.2.0). All machines can ping the access point, but they cannot ping each other. I don't totally understand why, because there is connection and all of the machines are in the same subnet. I realize this is a layer 3 device, but is there an issue because of this AP's lack of gateway capabilities? (i.e. no routing table, etc.)

  Read the article

• getting Internet connection sharing working in a slightly more complicated configuration

  - by tirichitirca t

  I have the following configuration: Computer A - Mac OSX 10.8.4, wireless & wired adapters Computer B - Windows 7 (64 bit), wireless & wired adapters, has internet connection via the wired adapter (ethernet) d-link wired/wireless router. Problem to solve: Connect from computer A to the internet through the wired connection of computer B. I tried the following: I set up a local network between A and B using the d-link router. The configuration is this: D-link router - 192.168.0.1 A - wired connection to the d-link router, static 192.168.0.101 (I could have used the wireless but I preferred the wired connection) B - wireless connection to the d-link router DHCP 192.168.0.102 (but I made sure it always gets the same address) B - wired connection to the internet using some address that begins with 10.x.y.z. In this configuration A can see B. I enabled ICS on the wired adapter of B. I set up the Gateway of A to point to B and DNS servers to point to the DNS servers specified for the 10.x.y.z address. It doesn't work, A goes only as far as B. It can ping the 10.x.y.z address of B though. I then found this article: http://terrybritton.com/windows-internet-connection-sharing-ics-not-working-with-linux-bridging-is-the-solution-916/. Terry is suggesting that a bridge should be defined on B between the two connections. I tried that but basically computer B is screwed as soon as I create the bridge. It can't connect to the internet anymore. It is as if the network bridge seems to think the traffic to the internet should go from the wired connection to the wireless and not the other way around. The other thing that puzzles me is the router itself. In general the router needs an internet address. In a normal configuration it is the router that gets the ip address and the internet traffic goes through the router. In my case I am not interested in that. So, any suggestions to get this working? I wouldn't shy away from using a commercial software but I would think windows 7 should allow me to do it. Thanks

  Read the article

• How To Get a Better Wireless Signal and Reduce Wireless Network Interference

  - by Chris Hoffman

  Like all sufficiently advanced technologies, Wi-Fi can feel like magic. But Wi-Fi isn’t magic – it’s radio waves. A variety of things can interfere with these radio waves, making your wireless connection weaker and more unreliable. The main keys to improving your wireless network’s signal are positioning your router properly — taking obstructions into account — and reducing interference from other wireless networks and household appliances. Image Credit: John Taylor on Flickr How To Get a Better Wireless Signal and Reduce Wireless Network Interference How To Troubleshoot Internet Connection Problems 7 Ways To Free Up Hard Disk Space On Windows

  Read the article

• FreeBSD 8.0 - Macbook: Trying to Connect to Wireless

  - by Koroviev

  What Happened A few days ago I installed FreeBSD 8from USB to my Macbook (Core Duo, 13"). The first thing I wanted to do was get my GUI back. I'm new to FreeBSD and it's my first time off of mac or windows, so I had some learning to do. I tried to a make clean install of xorg with ports but it returned many "No address record" errors. I realised I hadn't configured network settings and then the fun started. I ran ifconfig and it found 5 devices: msk0, ath0, fwe0, fwip0, lo0. * ath0 was identified as media: IEEE 802.11 Wireless Ethernet autoselect so it was clear which one I needed. From what I gathered, there are 3 files and two processes involved here: /boot/loader.conf /etc/wpa_supplicant.conf /etc/rc.conf /etc/rc.d/netif wpa_supplicant (which is a part of the former too) I'm certain it's a big simplification, so correct me if I'm wrong here. What I Tried I configured /boot/loader.conf with the few basic settings, and I'm most sure that this file is okay. The other 2 were more puzzling. I tried to make a network package in wpa_supplicant.conf. I found the ssid of the router, but the security wasn't so easy. The routers configuration on security is set to "Auto", with no explanation given. Other options are there, but Auto is selected. Another laptop uses WEP to connect (it's Vista, so I don't know how to get any more info than that), but I never configured it to do it. There's a string labled "wireless key" on the bottom of the router which I entered to set it up a new machine on the network (Windows and Macs, so it was simplified). I never had to choose a security type and only learned about them by installing FreeBSD. So perhaps WEP is what "Auto" means, but I can't find any other evidence. wpa_supplicant.conf seemed to never be correctly configured. I always got errors related to it and WPA_supplicant doesn't work. It gave me "Can't disable/enable WPA in the driver" errors and more once when I enabled -d -d. This was when I was trying some suspect configurations in rc.conf though. Usually it does nothing except hijack the shell and print "CTRL-SCAN-EVENT-RESULT" every 10 seconds. I learned how to clone the ath0 device to a wlandev interface (wlan0). ath0 is associated to it and their connection seems to go smoothly. But the wlan0's connection to the network is the problem. I couldn't create this with rc.conf, I do something wrong and get ifconfig: create: bad value errors whenever it's parsed. I did it via the shell instead. What Now? I scanned with wlan0 today: ifconfig wlan0 list scan It shows my router, even my neighbour's router. It was a relief to finally get some feedback. So wlan0 is UP and detects the router, but it is always status: no carrier. It can't associate with it and I can't figure out why. Running /etc/rc.d/netif start returns almost the same result as ifconfig would. It shows lo0 and wlan0, and sometimes ath0. I still not sure what lo0 is doing. So; how do I associate with it? We can assume it's WEP security based on how the other laptop is setup. I'll give every relevant output here. After boot, with a blank rc.conf this is what ifconfig returns: msk0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=11a<TXCSUM,VLAN_MTU,VLAN_HWTAGGING,TSO4> ether 00:17:f2:29:89:3b media: Ethernet autoselect ath0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 2290 ether 00:16:cb:bb:fe:65 media: IEEE 802.11 Wireless Ethernet autoselect (autoselect) status: no carrier fwe0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8<VLAN_MTU> ether 02:17:f2:60:ad:7e ch 1 dma -1 fwip0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 lladdr 0.17.f2.ff.fe.60.ad.7e.a.2.ff.fe.0.0.0.0 lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 I run: ifconfig wlan0 create wlandev ath0 It returns: wlan0: bpf attached wlan0: bpf attached wlan0: Ethernet address: xx:xx:xx:xx:xx:xx Ifconfig now returns: msk0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=11a<TXCSUM,VLAN_MTU,VLAN_HWTAGGING,TSO4> ether 00:17:f2:29:89:3b media: Ethernet autoselect ath0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 2290 ether 00:16:cb:bb:fe:65 media: IEEE 802.11 Wireless Ethernet autoselect (autoselect) status: no carrier fwe0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8<VLAN_MTU> ether 02:17:f2:60:ad:7e ch 1 dma -1 fwip0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 lladdr 0.17.f2.ff.fe.60.ad.7e.a.2.ff.fe.0.0.0.0 lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 wlan0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 ether 00:16:cb:bb:fe:65 media: IEEE 802.11 Wireless Ethernet autoselect (autoselect) status: no carrier ssid "" channel 1 (2412 Mhz 11b) regdomain 106 indoor ecm authmode OPEN privacy OFF txpower 20 bmiss 7 scanvalid 60 bgscan bgscanintvl 300 bgscanidle 250 roam:rssi 7 roam:rate 1 wme burst bintval 0 I run: ifconfig wlan0 up ifconfig wlan0 scan It finds my router and displays its details. I can feed it my routers details now, using: ifconfig wlan0 key value key value ... They show up in wlan0 when I run ifconfig, but it still doesn't associate. What details should I feed it, what exactly is needed? What, if anything, should I have in /etc/wpa_supplicant.conf (and if that psk is needed, is it most likely the string I mentioned above)? If I define the ssid in wpa_supplicant.conf, should I still feed it to wlan0? What process should I then use to associate it? 5 .How should I add these things to rc.conf so it will automatically do this at boot? A huge thank you in advance for any help you can give, I've spent hours crawling about the shell and I've learned quite a bit from it (I finally got the hang of vi too, from all that editing). But the sooner this is fixed, the better. *P.S. I was, and still am, wondering where the extra three devices come from (the wireless and wired were all I expected to find). lo0 is up at each boot and /etc/rc.d/netif, I have no idea what it is and can't find it in dmesg. Resources: /etc/loader.conf: Code: if_ath_load="YES" wlan_wep_load="YES" wlan_ccmp_load="YES" wlan_tkip_load="YES" /etc/wpa_supplicant.conf (I emptied it of everything unnecessary, because I was just causing errors) network={ ssid="BTVOYAGER2110-1C" } /etc/rc.conf has no network settings, I commented them out because of errors. There was my attempt to clone ath0 and feed it info, but I did if via the shell instead. I've included the output of dmesg as an attachment, in case it's useful. I'd include the boot text (which appears before login) but I don't know how to catch it into a text file. If it's needed and somebody tells me how, I will (actually, even if it's not needed, how can I view it to read?).

  Read the article

• Display wireless channels currently in use

  - by DrStalker

  Is there any windows utility to display the wireless channels are currently in use by the available wireless networks? I'd like to be able to see what existing channels are using so I can try to minimize interference on a new access point without a lot of trial and error.

  Read the article

• No Wireless Networks, BCM4313 [duplicate]

  - by TalonPlz

  This question already has an answer here: How to Install Broadcom Wireless Drivers (BCM43xx) 38 answers Just bought this little Asus 10 inch laptop that came with Ubuntu 12.04. Everything at my home was fine: Wireless identified and connected. As soon as I went to my girlfriend's house the trouble started. I couldn't connect to wireless (authentication... times out and asks for authentication) I started doing internet searching, tried a few solutions posted on line using terminal commands. No solutions. I decided to upgraded to 12.10-13.04 and that left me with a worse problem: I can no longer see ANY networks what so ever. Wireless card is ON, with out a doubt. Wired connection works. I have been fumbling with driver versions to no .avail, and have no idea which driver I am currently running I have a vague idea of what terminal lines to run: lshw: resources: irq:17 memory:f7d00000-f7dfffff *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth2 version: 01 serial: dc:85:de:56:c4:ea width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.20.155.1 (r326264) latency=0 multicast=yes wireless=IEEE 802.11abg resources: irq:17 memory:f7d00000-f7d03fff iwconfig: eth1 no wireless extensions. eth2 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off lo no wireless extensions. I am new and excited to start my Ubuntu and Linux life and this is only the first of my few hic cups i am sure! :) Thanks all UPDATE: Report from 2nd answer talon@Black1015E:~$ sudo apt-get remove --purge bcmwl-kernel-source [sudo] password for talon: Reading package lists... Done Building dependency tree Reading state information... Done Package 'bcmwl-kernel-source' is not installed, so not removed 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. talon@Black1015E:~$ wget http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb --2013-10-22 18:50:32-- http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb Resolving us.archive.ubuntu.com (us.archive.ubuntu.com)... 2001:67c:1562::15, 2001:67c:1562::13, 2001:67c:1562::14, ... Connecting to us.archive.ubuntu.com (us.archive.ubuntu.com)|2001:67c:1562::15|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1181334 (1.1M) [application/x-debian-package] Saving to: ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ 100%[======================================>] 1,181,334 3.37MB/s in 0.3s 2013-10-22 18:50:33 (3.37 MB/s) - ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ saved [1181334/1181334] talon@Black1015E:~$ arvh No command 'arvh' found, did you mean: Command 'arch' from package 'coreutils' (main) arvh: command not found talon@Black1015E:~$ arch x86_64 talon@Black1015E:~$ sudo dpkg -i bcmwl*.deb Selecting previously unselected package bcmwl-kernel-source. (Reading database ... 171895 files and directories currently installed.) Unpacking bcmwl-kernel-source (from bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb) ... Setting up bcmwl-kernel-source (5.100.82.112+bdcom-0ubuntu3) ... Loading new bcmwl-5.100.82.112+bdcom DKMS files... First Installation: checking all kernels... Building only for 3.8.0-32-generic Building for architecture x86_64 Building initial module for 3.8.0-32-generic Done. wl: Running module version sanity check. - Original module - No original module exists within this kernel - Installation - Installing to /lib/modules/3.8.0-32-generic/updates/dkms/ depmod........ DKMS: install completed. Error: Module b43 is not currently loaded Error: Module b43legacy is not currently loaded Error: Module ssb is not currently loaded Error: Module bcm43xx is not currently loaded Error: Module brcm80211 is not currently loaded Error: Module brcmfmac is not currently loaded update-initramfs: deferring update (trigger activated) Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.8.0-32-generic rebooting now

  Read the article

• good PCI-e Wireless card for Windows7?

  - by benwebdev

  Hi I've just build a 64bit Windows 7 PC but am unhappy with the piddly performance of the linksys USB wireless dingle I've used. Can anyone suggest a good PCIe alternative that will be stronger for connection and maybe faster. I dont see why my desktop should show a weaker performance on wireless than my laptop when its sat next to it or even my Palm Pre for that matter. any thoughts? UK based max around £60ish. thanks, Ben

  Read the article

• hp pavilion g6 1250 with a BCM 4313 doesn't see any wireless networks

  - by Ahmed Kotb

  i have tried using ubuntu 10.04 and ubuntu 11.10 and both have the same problem the driver is detected by the additional propriety drivers wizard and after installation, ubuntu can't see except on wireless network which is not mine (and i can't connect to it as it is secured) There are plenty of wireless networks around me but ubuntu can't detect them and if i tried to connect to one of them as if it was hidden connection time out. the command lspci -nvn | grep -i net gives 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) iwconfig gives lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off i guess it is something related to Broadcom driver .. but i don't know , any help will be appreciated UPDATE: ok i installed a new copy of 11.10 to remove the effect of any trials i have made i followed the link (http://askubuntu.com/q/67806) as suggested all what i have done now is trying the command lsmod | grep brc and it gave me the following brcmsmac 631693 0 brcmutil 17837 1 brcmsmac mac80211 310872 1 brcmsmac cfg80211 199587 2 brcmsmac,mac80211 crc_ccitt 12667 1 brcmsmac then i blacklisted all the other drivers as mentioned in the link the wireless is still disabled.. in the last installation installing the Brodcom STA driver form the additional drivers enabled the menu but as i have said before it wasn't able to connect or even get a list of available networks so what should i do now ? the output of command rfkill list all rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• hp pavilion g6 1250 wireless problems

  - by Ahmed Kotb

  i have tried using ubuntu 10.04 and ubuntu 11.10 and both have the same problem the driver is detected by the additional propriety drivers wizard and after installation , ubuntu can't see except on wireless network which is not mine (and i can't connect to it as it is secured) there are plenty of wireless networks around me but ubuntu can't detect them and if i tried to connect to one of them as if it was hidden connection time out. the command lspci -nvn | grep -i net gives 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) iwconfig gives lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off i guess it is something related to Broadcom driver .. but i don't know , any help will be appreciated UPDATE: ok i installed a new copy of 11.10 to remove the effect of any trials i have made i followed the link (http://askubuntu.com/q/67806) as suggested all what i have done now is trying the command lsmod | grep brc and it gave me the following brcmsmac 631693 0 brcmutil 17837 1 brcmsmac mac80211 310872 1 brcmsmac cfg80211 199587 2 brcmsmac,mac80211 crc_ccitt 12667 1 brcmsmac then i blacklisted all the other drivers as mentioned in the link the wireless is still disabled.. in the last installation installing the Brodcom STA driver form the additional drivers enabled the menu but as i have said before it wasn't able to connect or even get a list of available networks so what should i do now ? the output of command rfkill list all rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• Ralink RT3060 wireless device configuration on ubuntu 12.04

  - by Stephan

  concerning How do I get a Ralink RT3060 wireless card working? I'm running Ubuntu 12.04 with a 'LWPX07 Edimax EW-7711In 150M 1T1R WL PCI Card' which has a rt3060 chip. Out of the box the card is recognized as rt2800sta. I tried solution one, that didn't work. Still the card connects to the wireless network, but it seems to slow to load any pages. Then I tried solution 2, but then the network-manager doesn't see any wireless device. $ iwconfig lo no wireless extensions. ra0 Ralink STA Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. $ lsmod Module Size Used by rt3562sta 882296 0 $ lspci -v 05:02.0 Network controller: Ralink corp. RT3060 Wireless 802.11n 1T/1R Subsystem: Edimax Computer Co. Device 7711 Flags: bus master, slow devsel, latency 64, IRQ 23 Memory at ff9f0000 (32-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: rt2860 Kernel modules: rt3562sta, rt2800pci Am I missing a configuration step? How do I tell the network card which driver to use? Thanks in advance Stephan I found the problem. As described in stevens blog http://steveswinsburg.wordpress.com/2011/03/12/how-to-install-a-d-link-dwa-525-wireless-network-card-in-ubuntu-10-04/ sudo su make && make install "You need to use ‘sudo su’ and not just ‘sudo’ so it creates the directories properly." That is the problem with the solution describe above.

  Read the article

• Wireless drops on HP ENVY dv6 with RT3290 wireless, worked without problem prior to upgrading to Ubuntu 13.10, can it be fixed?

  - by Tim

  I have a HP ENVY dv6 Notebook PC with an AMD A10 quad core and RT3290 wireless. Since I upgraded from Ubuntu 13.04 to 13.10, the wireless connects, but then drops after a few minutes or longer, whether or not I am running openconnect to get through a VPN. If I attempt to run a remote X client (e.g. remote xterm) it drops. If I don't run an X client, it disconnects after a while, requiring a reload of the driver and reconnect. Wireless info... sudo lshw -c network *-network description: Wireless interface product: RT3290 Wireless 802.11n 1T/1R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 68:94:23:a7:09:cb width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.11.0-12-generic firmware=0.37 ip=192.168.1.115 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:55 memory:f0210000-f021ffff I have successfully built and installed the MediaTek driver with no luck on connecting, then the system hangs on reboot and I have to recover/undo the changes to boot successfully.

  Read the article

< Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >