Search Results

Search found 2066 results on 83 pages for 'cable'.

Page 50/83 | < Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >

  • Can SATA be used to connect computers?

    - by André
    Can SATA be used to connect two computers together, just like a crossover Ethernet cable would do ? I know SATA has no "networking" features and even though a controller may have multiple ports, the drives don't "see" each other, and that in SATA one device acts as the host (the computer) and the other device is some kind of "client" (the storage drive). But still, did anyone attempt to make a kernel module that would make one computer appear as a "client" (so that the host's SATA controller detects it as a standard hard drive) and then set up like a pseudo-Ethernet link or a very high speed serial link (and then run pppd on it and do networking) ? Note : I know this is an unprofessional and totally stupid idea, I'm just asking out of curiosity.

    Read the article

  • Cisco ASA 5505 and slow download speeds for Apple devices

    - by James
    For traffic routing through my ASA 5505, downloads for all Apple devices, including AppleTV iPad gen 1 IMac MacBook Pro are very slow. speedof.me show less than 1 Mbps download (where I should have 20 Mbps +), yet for any Windows-based device, the download speeds are in excess of 20 Mbps. The Windows device, including the iMac and MacBook Pro machines, are connected via ethernet cable. Why are Apple devices experiencing such pain? Is it an ASA setting, or something else? Thanks.

    Read the article

  • MacBook makes a noise from the power adapter every time I flip a widget...

    - by Timmy
    OK this is bizarre. But basically, what happens is on my MacBook (latest model) whenever I 'flip' a Dashboard Widget I hear a little noise for the duration of the flip: like a tiny continuous squeak noise. It's quite strange. However, it only ever happens when the MagSafe cable is plugged in. WHY?! :'( The noise appears to me emitted from the MagSafe area itself, but, there's not any other CoreAnimation or Quartzey bits that cause this to happen, it only happens with Dashboard widgets... The noise is very quiet and you can only hear it in a silent room. Edit: Running the latest Snow Leopard.

    Read the article

  • How do I replace the screen of a Dell Inspiron 1545?

    - by Ajus10
    I got a new screen for a Dell Inspiron 1545. The old screen says Dell Inspiron 1545 LP156WH1 (TL)(C1?) HD and the new one says Dell Inspiron 1545 LP156WH1 (TL)(C1?) LCD Does that make a difference? All I can get to work on the new screen is the backlight. The old screen had a crack. Now when I plug the old one in, it will not turn on at all. Could I have blown the inverter or messed up the cable?

    Read the article

  • Internet connection slower than network connection speed

    - by Mike Pateras
    I've got a computer connected to a wireless router on a different floor. When I look at the network connection, I'm told the signal strength is low, and that I've got a connection of about 26mbps (often higher). However, my internet connection on that machine is very slow. Speedtests show it at about 1-2mbps, and it really shows when loading pages and video. I have fiber optic internet access, and the machine that's connected to the router/modem via cable gets the 20mbps on speed tests, and is extremely fast in every day use. My question is, is the advertised 26mbps+ connection speed perhaps inaccurate, and that my wireless bandwidth is the likely bottleneck here? Or is the signal strength what's key here? And what might I do about this? Power cycling the router helped a bit, a speed test went as high as 6mbps after doing that.

    Read the article

  • Mini-DisplayPort to HDMI Adapter Sound Stopped Working

    - by jimdrang
    I have cancelled cable and want to watch the NCAA tournament games on my TV tonight through my 2011 Macbook Pro where I can stream the game in a browser. I have a cheap Mini-DisplayPort to HDMI converter that I have connected to my TV in the past and had no issues with audio or video, the problem is the audio has stopped working since the last time I used it a few months ago and now just keeps playing through the laptop speakers, but the video works fine. Everything with my setup is the same and when I try to force the audio output to the TV in the Audio system settings, my TV is not listed as an output option at all. I have tried various combinations of power cycling, replugging-in both devices and making sure the TV options are set properly to receive audio through HDMI but no luck. Anyone know what the issue could be?

    Read the article

  • Sonicwall - dual WAN ports - switch from one to another

    - by Charles
    Hi, Folks! I'm using a SonicWall NSA 240 which has two WAN ports (T1 and Comcast) and the LAN port has a cable which connects to a switch. From the switch, several cables connect to other switches. The SonicWall doesn't have DHCP enabled; one of our domain controllers running Windows Server 2003 also functions as a DHCP server. Is there a way for a user in our network to change connection from T1 to Comcast as their ISP or vice versa? In other words, if a user is connected via the T1, can he/she somehow connect via Comcast instead? Thanks, in advance, for your help! Sincerely, Charles

    Read the article

  • Wireless internet connection connects but internet does not work (no packets received). Wired does.

    - by Rodney
    When I connect my PC via ethernet cable to my ADSL router it works fine. When I connect via Wireless it connects and the internet will work for a random amount of time and then stop working. It stays connected with a strong signal but no packets are received. My laptop/iphone are right next to it and wireless works fine. If I open the Wireless USB status, it says it is connected to my SSID with full strength (54 mps - I am 3 meteres away from my router) and the activty shows as Packets 594 SENT and 105 RECEIVED (this goes up VERY slowly) I have tried the following: Turned off anitvirus and firewall completely. Tested the wifi signal- I am writing this on my laptop which is next to my PC and also has full wifi strength. Tried a different wireless adapter - I dug out an old PCI wireless card - it does the exact same thing. Compared all wireless settings to my laptop. I can ping google.com and it replies (sometimes with packet loss) When I reboot the PC it will connect for a minute or two (random time) and then just stops again. I tried Firefox, IE etc. no joy I have updated all latest versions (Netgear WG111v2) and drivers Checked Event Log - nothing unusual Ping the router (and even connect as admin for the few minutes when the internet does work) Changed the MTU down to 1200 using DrTCP Checked Device Manager for conflicts - none. I ping the router from the PC (192.168.0.10 - 192.168.0.1) and it replies with 4 packets. BUT, on my router admin page (which I access via http on my laptop wirelessly) - if I ping 192.168.0.10 all packets timeout (pinging my laptop 192.168.0.12 works fine) My router admin page shows the leased IP address for 192.168.0.10 (ie it is definitely talking to the router initially) Now I am out of ideas - please help. I think it is an OS/Software issue as I have tried 2 different wireless adapaters (PCI and USB) with the same result but all other wireless devices work fine around mine). It's not the firewall. It is getting assigned an IP address correctly (my PC gets 192.168.0.10, my laptop is .12) It is assigned by DHCP. As soon as I plug in the ethernet cable it all works fine. Repairing the adapter sometimes helps but it will always stop working after a random time. The wireless adapter always shows as connected with Excellent signal but the internet does not work. I am running Windows XP SP3 and have tried a Netgear WG111v2 USB adapter. Thanks in advance! UPDATE: The internet seems to be working, it is just either sending packets too small or slow to work (some small pages load bits of them very slowly but then hang). XP seems to have a networking diagnostic app - here is the output: Last diagnostic run time: 08/30/10 08:16:38 IP Configuration Diagnostic Invalid IP address info Valid IP address detected: 192.168.0.10 IP Layer Diagnostic Corrupted IP routing table info The default route is valid info The loopback route is valid info The local host route is valid info The local subnet route is valid Invalid ARP cache entries action The ARP cache has been flushed Gateway Diagnostic Gateway info The following proxy configuration is being used by IE: Automatically Detect Settings:Disabled Automatic Configuration Script: Proxy Server: Proxy Bypass list: info This computer has the following default gateway entry(ies): 192.168.0.1 info This computer has the following IP address(es): 192.168.0.10 info The default gateway is in the same subnet as this computer info The default gateway entry is a valid unicast address info The default gateway address was resolved via ARP in 1 try(ies) info The default gateway was reached via ICMP Ping in 1 try(ies) info TCP port 80 on host 65.55.12.249 was successfully reached info The Internet host www.microsoft.com was successfully reached info The default gateway is OK DNS Client Diagnostic DNS - Not a home user scenario info Using Web Proxy: no info Resolving name ok for (www.microsoft.com): yes No DNS servers DNS failure HTTP, HTTPS, FTP Diagnostic HTTP, HTTPS, FTP connectivity info FTP (Passive): Successfully connected to ftp.microsoft.com. info HTTP: Successfully connected to www.microsoft.com. warn HTTPS: Error 12002 connecting to www.microsoft.com: The operation timed out warn HTTPS: Error 12002 connecting to www.passport.net: The operation timed out error Could not make an HTTPS connection. info Redirecting user to support call WinSock Diagnostic WinSock status info All base service provider entries are present in the Winsock catalog. info The Winsock Service provider chains are valid. info Provider entry MSAFD Tcpip [TCP/IP] passed the loopback communication test. info Provider entry MSAFD Tcpip [UDP/IP] passed the loopback communication test. info Provider entry RSVP UDP Service Provider passed the loopback communication test. info Provider entry RSVP TCP Service Provider passed the loopback communication test. info Connectivity is valid for all Winsock service providers. Wireless Diagnostic Wireless - Service disabled Wireless - User SSID action User input required: Specify network name or SSID Wireless - First time setup info The Wireless Network name (SSID) to which the user would like to connect = RodSof Wifi. Wireless - Radio off info Valid IP address detected: 192.168.0.10 Wireless - Out of range Wireless - Hardware issue Wireless - Novice user Wireless - Ad-hoc network Wireless - Less preferred Wireless - 802.1x enabled Wireless - Configuration mismatch Wireless - Low SNR Network Adapter Diagnostic Network location detection info Using home Internet connection Network adapter identification info Network connection: Name=Local Area Connection 2, Device=Realtek RTL8168C(P)/8111C(P) PCI-E Gigabit Ethernet NIC, MediaType=LAN, SubMediaType=LAN info Network connection: Name=Wireless USB, Device=NETGEAR WG111v2 54Mbps Wireless USB 2.0 Adapter, MediaType=LAN, SubMediaType=WIRELESS info Both Ethernet and Wireless connections available, prompting user for selection action User input required: Select network connection info Wireless connection selected Network adapter status info Network connection status: Connected HTTP, HTTPS, FTP Diagnostic HTTP, HTTPS, FTP connectivity info FTP (Active): Successfully connected to ftp.microsoft.com. warn HTTP: Error 12007 connecting to www.microsoft.com: The server name or address could not be resolved warn HTTP: Error 12002 connecting to www.hotmail.com: The operation timed out warn HTTPS: Error 12002 connecting to www.passport.net: The operation timed out warn HTTPS: Error 12002 connecting to www.microsoft.com: The operation timed out error Could not make an HTTP connection. error Could not make an HTTPS connection.

    Read the article

  • Very low throughput on 10GbE network

    - by aix
    I have two Linux machines, each equipped with a Solarflare SFN5122F 10GbE NIC. The two NICs are connected together with an SFP+ Direct Attach cable. I am using netperf to measure TCP throughput between the two machines. On one box, I run: netserver and on the other: netperf -t TCP_STREAM -H 192.168.x.x -- -m 32768 I get: MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.x.x (192.168.x.x) port 0 AF_INET Recv Send Send Socket Socket Message Elapsed Size Size Size Time Throughput bytes bytes bytes secs. 10^6bits/sec 87380 16384 32768 10.02 1321.34 The measured throughput is 1.3Gb/s. This is 7.5x below the theoretical maximum, and only 30% faster than 1GbE. What steps can I take to troubleshoot this?

    Read the article

  • How do you test if a PCI slot is working - motherboard diagnostic software?

    - by Adam
    I suspect that my motherboard is bad, and that my PCI-E slot is not working. I have a Gigabyte motherboard that had a Hauppage 2250 working fine in the PCI-E slot for many months. However - recently - would not get TV channels that I used to get --- until finally Media center cant detect any channels at all. Got a new tuner card (ATI 350 card) - cant detect any channels. The cable signal is good - I have it connected directly to a TV - all channels come in clear. SO that is why I suspect a motherboard problem. Are there any motherboard diagnostic scanner utilities that can verify I need a new motherboard

    Read the article

  • When my printer fails to print with only "printer error" as the message, how can I find details?

    - by lavinio
    Setup: Dell Latitude D620 in the docking station HP color laserjet 2550L Parallel cable Sometimes when I undock (and I do suspend before undocking and docking), when I reattach, the printer will not print. It simply says "error", with no description. Killing and restarting the spooler will not help, but rebooting will. There is nothing in the system event logs, nor does the print spooler window provide any details other than "error" My question is, when there is an error, is there any way to find out what is causing it to get stuck, so that I can "unstuck" it instead of rebooting?

    Read the article

  • Can you play Halo 2 and Halo 3 on an Xbox360 Arcade?

    - by Jeremy Rudd
    I'm looking at purchasing a Xbox360 because I've wanted to catch up with the Halo trilogy. Does the cheap Arcade edition console support Halo 2 and Halo 3? Would I be able to save my game progress in single player? Would I be able to play online in typical maps? Would I be able to play games using the DVD drive or do I have to download everything? Does the tiny HDD hurt even if I don't download any games, trailers or music? Are there any other differences in comparison to the Xbox360 Pro? I have a regular TV that uses the composite cable, so I don't need the HDTV support in the Pro edition.

    Read the article

  • NIC light is turned off after boot on Redhat 4.6 server

    - by hoffmandirt
    I have a 2950 blade server setup with Red Hat 4.6 installed. I cannot get the NIC to work properly after reinstalling Linux. I activated the NIC, but the NIC light will not turn on when I plug the network cable into the hub. The status light on the hub will not turn on either. If I run ifconfig, the NIC status is UP. Also I can ping the IP address that I assign to the Linux machine, but I can't ping anything else that is plugged into the hub. When I reboot the system, the NIC light will stay on until the system fully boots and then it will turn off again. Is there something else that I need to do to get the NIC working? It appears to be disabled even though ifconfig says that it is UP. Maybe I need to configure something within the blade server (iDRAC)?

    Read the article

  • Black stripe appears to the right of the screen, impossible to get rid of

    - by Gabriele Cirulli
    After clicking the "Auto Config" button on my Acer AL2216w screen a stripe appeared on the right of the screen where the screen doesn't "exist" and I can't seem to take the screen viewport back even by using the OCD setting and moving it to the right. The left part of the screen is also hidden and I'm not able to see what's going on there. The PC is connected to the screen through a DVI adapter and a VGA cable. I also use multiple monitors and this is the second monitor. Anyway this seems not to be a related issue, as this used to happen even when I only had a single monitor. I managed to fix this issue once but it was more than two years ago and I can't remember what I did, and out of all of the things I've tried so far (connecting the screen to another PC and performing auto adjustment, switching the cables, etc.) none worked. Here's how it looks: Can anyone help me fix this?

    Read the article

  • How do I keep second monitor (HDTV) from auto-disabling in XP when it is turned off?

    - by ThantiK
    I have a new 32" TV that I hooked up to the HDMI port on the back of my video card to use as a second monitor. I used an HDMI/DVI cable to hook it to the TV, and whenever I turn my TV off, XP disables the device tied to the TV so each time I want to use the TV as the monitor, I have to go into my display properties and enable it; it gets pretty annoying. How do I turn this 'feature' off? -- I have an NVidia card should it be specific to the nvidia control panel.

    Read the article

  • How can I watch TV on my Computer (Not Online)?

    - by Sammy
    Novice question here, but how can I watch TV on my PC without using online sites? I have heard of tv tuners but is it just a matter of hooking a tv tuner to your computer and that's it? Do I have to just buy a tuner or pay for a service as well? If no service needs to be paid for, will I get just regular channels or cable/satellite channels as well? Will my PC need to be connected to the Internet when I want to watch TV? Do I need any type of software aside from the hardware tuner?

    Read the article

  • remote desktop over wireless

    - by tbischel
    So I'm trying to run remote desktop on my laptop to connect to my home desktop. I have a problem where this works fine if I connect my laptop with an ethernet cable, but fails when I try to use wireless internet access (which works fine for normal internet surfing). I've experienced this problem at home with my wireless router, and at work with the wireless network they have there, so I'm inclined to believe that its a setting local to my machine rather than the router blocking the requests... but I'm not sure where to look. Any suggestions?

    Read the article

  • Multi serial devices on one port

    - by adopilot
    I am developing one software for managing parking lot. System is designed to use four HID RFID devices for authorization clients on gates. Each device should be connected to server by Serial port RS232. Now I wondering is there some device or method to join all that devices on one device and after that to I have only one RS232 cable connected to server. My problem is in that RFID card readers are simple (stupid) devices and there I am not able to change anything, but Ill like to know from which specific device is coming input. What Ill want to do with that new device which need to join four readers is to add suffix or prefix to string that sent from RFID card reader. So I can identify device that is sending card number to my server. I am developing my system on Win platforms.

    Read the article

  • Windows Server 2003 Router with PortForwarding

    - by jM2.me
    Hello, I am owning a small company and we have purchased a server to setup few server applications on it as well as other software. We would like to setup our network in following way Internet<-WindowsServer2003 as router<-Switch<-Office Computers Server has two nic interfaces and we have 24ports 1GB network switch connected to one nic and internet connection to another nic. Our ISP is Frontier and we have Fios 25/25. We get network cable out of ONT box directly connected to our server. There are no modems/routers. Setting up DHCP on windows 2003 is easy job but we would like to have the ability to port forward some ports from office computers. I have some knowledge in networking but not as much. How could I setup FHCP server on win2k3 with the ability to port forward some ports to office computers? Thank you for your time

    Read the article

  • Getting packets from one port to another on a Dell PowerConnect 2824 switch

    - by Arvo Bowen
    I have a dell PowerConnect 2824 and I have a cat 5 cable connected from port 1 to port 23. Port 1 is reserved for VLAN 1 (the only VLAN that can manage the switch) and port 18-23 belong to VLAN 112. I currently have the switch setup with ip 10.71.3.5/27 and a test machine plugged into port 22 with IP address 10.71.3.30/27. For some reason I can not ping 10.71.3.5 from my test machine (10.71.3.30). Note: When I try to ping the server plugged into port 21 (IP: 10.71.3.7/27) also VLAN 112, I get responses just fine. Note: When I plug my test machine directly into port 1, I can ping 10.71.3.5 just fine. Quick Recap: Switch IP: 10.71.3.5 Port 1 - dedicated to management - (VLAN1) Port 21 - SERVER (10.71.3.7/27) - (VLAN112) Port 22 - test machine (10.71.3.30/27) - (VLAN112) Port 23 - dedicated to management (to hop over to VLAN 1 from VLAN 112) - (VLAN112)

    Read the article

  • Belkin router issue

    - by walr1
    Hi, My cousin and I bought a wireless Belkin router for testing purposes. Please keep in mind for all of our tests there is no ethernet cable plugged in, just the router's power cord. We have been trying to "flood" it with PING requests on its default address 192.168.2.1, but it isn't doing a thing; not even logging any attempts of too many requests. I've disabled the firewall, disabled PING request block, etc. Any idea why this thing isn't being affected? We sent 4 million packets and it hasn't done a thing. Quite odd! Thanks.

    Read the article

  • Why does changing the physical socket on your router cause delays?

    - by Josh Browning
    My question involves the delays involved with changing which physical socket your ethernet cable is connected to. I am aware that if you are connected to a router on a network and then change which physical socket on that router you are using you will gain very small additional delays initially. However I am curious as to what causes these delays. I originally thought it was to do with the infromation stored in the routing table and whether that was allocated to a specific socket on the router or not. Although, if your IP address is the same then I don't understand why there would be delays because I would of assumed that any information within the router was linked to an IP address rather than a physical socket.

    Read the article

  • Minimum power requirement for VGA vs. its working

    - by Shiki
    Got a new XFX GTX260^2 video card. The only problem is the "Minimum power" is 500W on the box. I've got a Chieftec 450AA PSU with just a minimal number of attached stuff (1hdd, WD green; 6gb (4module) ram; dvd writer). Bought a cable for the 6pin power input on the card. Got picture, works in every aspect. Still. Should I get a new PSU (like a Corsair or Antec 600W)? Will the card perform slower with this PSU? (Yeah the last part is a particular question but in I'm also asking in generic. I was wondering about this so many times and I hope we'll put and end for this question for once and for all.)

    Read the article

  • Stream music from Laptop to iPod Touch over Wi-Fi

    - by codeulike
    Rather than running a long cable from my Laptop to my stereo, I've been thinking for a while about getting one of those wireless devices that lets you transmit audio from your PC to a receiver plugged into the stereo. Then I realised I already have hardware that can potentially do this - I have an iPod Touch, and a Wi-Fi network in the house. So, is there some iPod Touch App that will let the iPod act as a Wi-Fi music receiver? And presumably, a corresponding piece of broadcast software for my (Windows Vista) Laptop?

    Read the article

  • Fujitsu siemens V6535 - crash when going standby ?

    - by marc
    Welcome, I trouble with my laptop fujitsu siemens model V6535. My siemens work under Windows 7, and from upgrade time (vista to 7) notice something what make me really angry. When my siemens go to standby mode (when i don't use it for some time), power diode change to red and start blinking (standbay mode). When i push power button (wake up it), blinking diode change to green but nothing else happend (nothing on display, no sound of HDD). When i press power button few second and try turn it on again... it wont display anything... i have unplug charger and then shutdown and power on again without power cable. Then he start working... Few days ago i done upgrade bios to nevest version... but it don't help... Anyone have idea what can be wrong ?

    Read the article

< Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >