Search Results

Search found 4316 results on 173 pages for 'disabled'.

Page 50/173 | < Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >

  • Problems when trying to connect to a router wirelessly

    - by Ruud Lenders
    The situation - At my girlfriend's parents' place there are six Windows 7 devices that are wired or wireless connected to a router: 3 dekstops and 3 laptops. There are also several smartphones using the router. The router is secured with WPA2 (AES). The problem - We never had any problems with the router for over a year. But recently - about 3 weeks ago - my girlfriend's laptop (HP) and my laptop (ASUS) started to develop problems while trying to connect to the router. The router has stopped showing up from the network list. Sometimes it comes back and shows up, but then it keeps saying something along the lines of "Could not connect", and not long after that it dissapears again. The range of the router is not the problem here, because we experience the same when we sit next to the router. Sometimes, if we are lucky, and waited a long time (10-15 minutes) without using the laptop for anything, the laptop will eventually succesful connect to the router. The attempts - Of course, the Window 7 troubleshooter. We tried troubleshooting the connection problems and the wireless network adapter, but no luck. We also reset the router enough times to know that's not helping either. Here's the full list of things we tried, but did not help: Running the Windows 7 troubleshooter Resetting the router (more than once) Setting the router settings to factory defaults Disconnecting all other devices except one laptop Applying a system restore Trying static/dynamic IP/DNS - Dynamic is better, right? Enabling/disabling IPv6 - Should I keep IPv6 disabled? Running the command: netsh wlan stop hostednetwork Running the command: netsh wlan set hostednetwork mode=disallow Updating/reïnstalling wireless adapter drivers The tests - To help finding the core of the problem, we tested the following: Plugging an ethernet cable in the router and in our laptops - worked fine Connecting someone else's laptop to the router (wireless) - worked fine Connecting our laptops to someone else's router - worked fine The router - This information might be relevant: Router model: Sitecom 300N Wireless Router Router hardware: version 01 The DCHP Server's IPs range from 192.168.0.100 to 192.168.0.200. Router settings: Wireless channel: 12 Channel bandwidth: 20/40 MHz Extension channel: 8 Preamble type: Long 802.11g protection: Disabled UPnP: Enabled The laptops - If you are wondering about our laptops: My laptop model: ASUS Pro64JQ Girlfriend's laptop: HP Pavillion G6 OS: Both Windows 7 Professional x64 - with Service Pack 1 My wireless adapter: Atheros AR9285 AdHoc 11n: Enabled The question - Does anyone have experienced the same problems as I do? Or does someone know how to solve this? Are there more tricks I can try, or settings I should change? Note - Our laptops are not slow or old. My laptop is 1.5 years old, and the other laptop is just 5 months old. I know how to keep laptops clean and I'm pretty sure both laptops are not bloated with useless software.

    Read the article

  • Remote Desktop and Num Lock

    - by PressAnyKey
    Whenever I log into my Windows 7 desktop from my Windows 7 laptop using RDC, the Num Lock is enabled on the host computer and it is not disabled after disconnecting. What can I do to stop the Num Lock from being enabled or automatically disable it at the end of the session? (I do not know if this happens only on Windows 7 and have no way of checking, so I went with the generic windows tag)

    Read the article

  • Installing Git on Ubuntu 12.04

    - by Sven Jung
    I installed git with gitolite on my vserver using this tutorial. But I've got a problem to clone the gitolite-admin repo to my computer. The user is created with the option --disabled-password But if I try to clone with git clone git@<server>:gitolite-admin.git he asks not only for the passphrase of my rsa_key but also for the password of the gituser. Anyone an idea? I thought the user is created without password and I don't know what to type in

    Read the article

  • Mod_rewrite with UTF-8 accent, multiviews , .htaccess

    - by GuruJR
    Problem: with Mod_rewrite, multiview & Apache config Introduction: The website is in french and i had problem with unicode encoding and mod_rewrite within php wihtout multiviews Old server was not handling utf8 correctly (somewhere between PHP, apache mod rewrite or mysql) Updated Server to Ubuntu 11.04 , the process was destructive lost all files in var/www/ (the site was mainly 2 files index.php & static.php) lost the site specific .Htaccess file lost MySQL dbs lost old apache.conf What i have done so far: What works: Setup GNutls for SSL, Listen 443 = port.conf Created 2 Vhosts in one file for :80 and :443 = website.conf Enforce SSL = Redirecting :80 to :443 with a mod_rewrite redirect Tried to set utf-8 everywhere.. Set charset and collation , db connection , mb_settings , names utf-8 and utf8_unicode_ci, everywhere (php,mysql,apache) to be sure to serve files as UTF-8 i enabled multiview renamed index.php.utf8.fr and static.php.utf8.fr With multiview enabled, Multibytes Accents in URL works SSL TLS 1.0 What dont work: With multiview enabled , mod_rewrite works for only one of my rewriterules With multiview Disabled, i loose access to the document root as "Forbidden" With multiview Disabled, i loose Multibytes (single charater accent) The Apache Default server is full of settings. (what can i safely remove ?) these are my configuration files so far :80 Vhost file (this one work you can use this to force redirect to https) RewriteEngine On RewriteCond %{HTTPS} off RewriteRule (.*) https://%{HTTP_HOST}%{REQUEST_URI} LanguagePriority fr :443 Vhost file (GnuTls is working) DocumentRoot /var/www/x ServerName example.com ServerAlias www.example.com <Directory "/var/www/x"> allow from all Options FollowSymLinks +MultiViews AddLanguage fr .fr AddCharset UTF-8 .utf8 LanguagePriority fr </Directory> GnuTLSEnable on GnuTLSPriorities SECURE:+VERS-TLS1.1:+AES-256-CBC:+RSA:+SHA1:+COMP-NULL GnuTLSCertificateFile /path/to/certificate.crt GnuTLSKeyFile /path/to/certificate.key <Directory "/var/www/x/base"> </Directory> Basic .htaccess file AddDefaultCharset utf-8 Options FollowSymLinks +MultiViews RewriteEngine on RewriteRule ^api/$ /index.php.utf8.fr?v=4 [L,NC,R] RewriteRule ^contrib/$ /index.php.utf8.fr?v=2 [L,NC,R] RewriteRule ^coop/$ /index.php.utf8.fr?v=3 [L,NC,R] RewriteRule ^crowd/$ /index.php.utf8.fr?v=2 [L,NC,R] RewriteRule ^([^/]*)/([^/]*)$ /static.php.utf8.fr?VALUEONE=$2&VALUETWO=$1 [L] So my quesiton is whats wrong , what do i have missing is there extra settings that i need to kill from the apache default . in order to be sure all parts are using utf-8 at all time, and that my mod_rewrite rules work with accent Thank you all in advance for your help, I will follow this question closely , to add any needed information.

    Read the article

  • Disable WLan if Wired/Cable Network is available

    - by ifischer
    The question says it all. All i want is that my W-Lan connection should be disabled whenever a wired connection is available. What would be the easiest way to do that in Ubuntu/Gnome? In all guides (for instance some about guessnet) i found i had to configure my whole network configuration (WPA keys, DHCP, ...), but i find that a bit too complicated for such a simple use case. I just want to disable wlan0 when eth0 is connected.

    Read the article

  • How to stop the Google Update background tool?

    - by Dimitri C.
    On my Windows Vista PC, there is always an instance of "GoogleUpdate.exe" running. I find this annoying, so I'd like to make sure it doesn't start automatically. This proves to be not so easy, as I have tried these solutions: I disabled the "Google updateservice" service I removed the registry section "HKCU\Software\Microsoft\Windows\CurrentVersion\Run\Google Update" None of these worked. The registry section is simply re-added. Does anyone know the trick to avoid GoogleUpdate.exe to be started after booting the system?

    Read the article

  • Windows Media Player Network Sharing eating lots of CPU

    - by reyjavikvi
    There is a process, wmpnetwk.exe, which sometimes goes crazy and starts eating like 60-70% CPU. If I kill the process it just comes back again, so the only solution I've found is to stop the WMPNetworkSvc service, which makes the whole thing stop. I don't use WMP, so I don't care if this is disabled, but I'd like to know what's causing it (Google has revealed that it also happened to other people), and if there's a more permanent way of fixing the problem.

    Read the article

  • emule cannot create Incoming Files directory

    - by Tim
    Hi, I have installed emule on Windows 7. When I start emule, I will receive a message "failed to create Incoming Files directory 'C:\Program Files\eMule\Incoming' - Access is denied", similar message for "C:\Program Files\eMule\Temp" and "Failed to initialize cryptokeys - secure ident disabled". It looks like Windows 7 does not allow emule to make such operation. How can I give emule the right to do what it needs? Thanks!

    Read the article

  • Why does unpartitioned Hitachi HDS5C3020 drive start consuming 50% more power 15 minutes after boot?

    - by Pro Backup
    In a Debian 6.0.6 system there are 74 pieces of 2TB Toshiba DT01ABA200 drives. These drives are identified as Hitachi HDS5C3020BLE630 drives running firmware revision MZ4OAAB0. 64 Drives attached via HP SAS expander cards to an LSI 2008 SAS controller, another 5 drives are connected directly to the mainboard, 4 drives are connected to a Sil based PCI controller and last 1 drive is only powered and has no data cable connected. The controller LSI and Sil card's their onboard BIOS are both disabled and the mpt2sas and sata_sil modules are removed from the Linux debian 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux kernel. The mpt2sas module is loaded after boot using a modprobe command in /etc/rc.local. These 74 drives are not partitioned, neither formatted and also not mounted. The system consumes: with 0 drives: 70.6 - 70.9 Watt (also 15 minutes after boot); with 74 drives: 330 - 360 Watt, just after boot (is equivalent to 3.5 - 3.9W per drive in idle state); with 74 drives: 420 - 466 Watt, each time in the 15th minute of uptime (is equivalent to 4.7 - 5.3W per drive in idle state). The drive specification lists 4.7W as read/write, and 3.3W as idle power consumption. The increased power consumption is most likely on the 5V line, because after roughly 1 minute an "over current protection" (OCP) of the power supply (PSU) shuts down the power. The used PSU is a single rail model with an OCP of 122A on the 12V line and 55A on the 5V line. Regression: It doesn't matter whether the drive its APM value is set to disabled or 1 (maximum power saving). The operating system records no read/write activity in /proc/diskstats. The values there are identical (28 read, 0 write operations) as immediately after the modprobe operation. Can't test what happens when booting into the mainboard it's BIOS - to exclude any OS intervention - because the Super Micro X8SI6-F mainboard running firmware 06/27/12 has a bug that incorrectly reads a +74.0 C CPU sensor temperature as "High" in BIOS mode, and shuts down the power after 1 minute. What might be causing the drive read/write activity on all drives in the 15th minute after boot and how to prevent it from happening?

    Read the article

  • Does BitLocker reduce write reliability?

    - by Unsigned
    For the purposes of this question, BitLocker refers to the BitLocker-to-go variety on a disk with write-caching disabled. NTFS supports metadata journaling, which, although not completely failsafe, does mitigate certain types of potential filesystem errors. Assuming an NTFS volume is protected with BitLocker, does this reduce the failure tolerance? Would a power failure during a write to an NTFS volume, that's protected with BitLocker, be more prone to corruption than on an unencrypted NTFS volume?

    Read the article

  • disable using of desktop.ini file

    - by osgx
    Hello How can i disable explorer in winXP from using desktop.ini /folder.ini files? some viruses are on the flash card, and they can be in that files. I want make explorer safe from opening such flashes. Autorun is disabled. Yes, there are another file managers, but it is comp of my girlfriend.

    Read the article

  • Apache Proxy HTTP CONNECT method enabled

    - by John
    I'm using Apache as reverse proxy for several different projects. PCI-DSS compliance scanning shows that my Apache is having HTTP CONNECT method enabled. as stated on Acunetix's site - http://www.acunetix.com/vulnerabilities/apache-proxy-http-connect-metho/ As far as I know, CONNECT is used by the web server to tunnel SSL to application server. Any suggestion how should I fix this? Otherwise, anyone know how should I perform the test if my Apache's HTTP CONNECT method is enabled/disabled?

    Read the article

  • Anyone else experiencing high rates of Linux server crashes during a leap second day?

    - by Bron Gondwana
    POSTMORTEM Anticlimax: only thing that died was my VPN (openvpn) link to the cluster, so there was an exciting few seconds while it re-established. Everything else was fine. Starting back ntp everywhere. If you look at Marco's blog at http://my.opera.com/marcomarongiu/blog/2012/06/01/an-humble-attempt-to-work-around-the-leap-second - he has a solution for phasing the time change over 24 hours using ntpd -x to avoid the 1 second skip. Give that a go if it matters to you. For the systems I run, the jump isn't a problem. Just today, Sat June 30th - starting soon after the start of the day GMT. We've had a handful of blades in different datacentres as managed by different teams all go dark - not responding to pings, screen blank. They're all running Debian Squeeze - with everything from stock kernel to custom 3.2.21 builds. Most are Dell M610 blades, but I've also just lost a Dell R510 and other departments have lost machines from other vendors too. There was also an older IBM x3550 which crashed and which I thought might be unrelated, but now I'm wondering. The one crash which I did get a screen dump from said: [3161000.864001] BUG: spinlock lockup on CPU#1, ntpd/3358 [3161000.864001] lock: ffff88083fc0d740, .magic: dead4ead, .owner: imapd/24737, .owner_cpu: 0 Unfortunately the blades all supposedly had kdump configured, but they died so hard that kdump didn't trigger - and they had console blanking turned on. I've disabled console blanking now, so fingers crossed I'll have more information after the next crash. Just want to know if it's a common thread or "just us". It's really odd that they're different units in different datacentres bought at different times and run by different admins (I run the FastMail.FM ones)... and now even different vendor hardware. Most of the machines which crashed had been up for weeks/months and were running 3.1 or 3.2 series kernels. The most recent crash was a machine which had only been up about 6 hours running 3.2.21. THE WORKAROUND Ok people, here's how I worked around it. disabled ntp: /etc/init.d/ntp stop created http://linux.brong.fastmail.fm/2012-06-30/fixtime.pl (code stolen from Marco, see blog posts in comments) ran fixtime.pl without an argument to see that there was a leap second set ran fixtime.pl with an argument to remove the leap second NOTE: depends on adjtimex. I've put a copy of the squeeze adjtimex binary at http://linux.brong.fastmail.fm/2012-06-30/adjtimex - it will run without dependencies on a squeeze 64 bit system. If you put it in the same directory as fixtime.pl, it will be used if the system one isn't present. Obviously if you don't have squeeze 64 bit... find your own. I'm going to start ntp again tomorrow. As an anonymous user suggested - an alternative to running adjtimex is to just set the time yourself, which will presumably also clear the leapsecond counter.

    Read the article

  • cron job email customization

    - by user12145
    I have a list of cronjobs where some executes daily and others execute very 15 minutes. I do want to receive an email for the ones executed daily, but wants email disabled for the ones executing every 15 minutes(or maybe receive a daily email), is there a way to do this in crontab?

    Read the article

  • Trusted Sites via GPO: <*.> gets left off

    - by HannesFostie
    As stated in the question title: one of our end users has to make use of a web application which requires her to add the website to trusted sites. By default, this is disabled, but after my colleague added the sites to the GPO pushing these in such form: *.domain.com it shows up as domain.com in her trusted sites. Has anyone encountered or even fixed this issue?

    Read the article

  • Cannot clear away BitDefender Internet Security system tray message

    - by unknown (google)
    I have BitDefender IS 2008 installed on my PC. In the last few days I have noticed the taskbar icon grumbling 1 issue requires your attention The Real-Time File Scanning is disabled and no amount of clicking "Fix" solved this issue. I have tried umpteen reboots and what have you. I really don't want to uninstall and re-install BitDefender (unless there's no other way out). How do I clear away the notification message?

    Read the article

  • Disable option never goes away for network adapters

    - by mathee
    Hi, guys, I'm running Windows 7. Whenever I disable the wireless adapter, the "Disable" option does not change to "enable". Similarly, for the "Local Area Connection", when I click on "Disable", the adapter gets disabled, but the "Disable" option remains. In summary, I am never offered the option to enable an adapter.

    Read the article

  • How can I use Zend Studio for Java development?

    - by Itay Moav
    I have the Zend Studio, which is a PHP editor based on Eclipse. I want to use it now to develop some Java. I think Zend has disabled all the Java centric project/views/perspectives that come with Eclipse (or may be not included the right plugins?) What steps should I take to use it, instead of having two Eclipse instances open at the same time.

    Read the article

  • How can make rsync use sudo

    - by Bryan M.
    I use rsync to mirror a number of folders on our failover server. However, some of our files, such as thumbnails or full-text indexes, are generated by our applications under the web user (named 'nobody'), and default to restrictive permissions. Also, I'm doing this over ssh, where root access is disabled, and I'd like to keep it that way, if possible. Is there any reasonable way I can tell rsync to run as sudo? Or should I look into changing the file permissions? Thanks

    Read the article

  • remaping ctrl+capslock and alt+capslock on ubuntu

    - by qtwtetrt
    I'm trying to disabled capslock and make the following remaps ctrl+capslock = capslock alt+capslock = escape (since my escape key is broken) right now I'm trying to use xmodmap i have only the following keycode 66 = NoSymbol Caps_Lock this disables capslock and maps shift+capslock to capslock but what I what is ctrl+capslock instead of shift+capslock and I have no idea how to map alt+capslock to escape any help is appreciated, thank you

    Read the article

  • windows xp - shift key pops up a menu

    - by shachar
    Helo all! A wierd shift-key problem, for which all I found was sticky keys answers First of all, I have all the sticky keys and related, Disabled. Every windows that is currently in focus, if I press the left shift-key alone, pops up the current window menu. I have no idea how and why this has happened, or how to disable it. I could not find any reference in google about it (perhaps my search-string was not good..) any help would be appriciated

    Read the article

  • Oracle 11g RDBMS Enterprise Edition download?

    - by Oliver Michels
    I am looking for a URL where i can download the Enterprise Edition of Oracle 11g. I know that i can download the Standard Edition of 11g at Oracle's technet, but as i would like to use some of those enterprise options, which are disabled in standard, i would rather reinstall the enterprise software on our development server.

    Read the article

  • Does Windows 8 support wubi installation?

    - by vignesh4303
    I recently installed Windows 8 from MSDN. I used to install Linux within Windows in my Windows operating systems. But when I tried to install my Ubuntu 10.10 with Wubi installer the option to install with wubi was disabled. Help me to install Ubuntu with Wubi installer on Windows 8 if Windows 8 supports it. If it does not, please recommend any other alternative to Wubi. I use Wubi mainly because I can easily remove the Linux operating system.

    Read the article

< Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >