Search Results

Search found 7875 results on 315 pages for 'wired networking'.

Page 50/315 | < Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >

• Duplicate ping response when running Ubuntu as virtual machine (VMWare)

  - by Stonerain

  I have the following setup: My router - 192.168.0.1 My host computer (Windows 7) - 192.168.0.3 And Ubuntu is running as virtual machine on the host. VMWare network settings is Bridged mode. I've modified Ubuntu network settings in /etc/netowrk/interfaces, set the following config: iface eth0 inet static address 192.168.0.220 netmask 255.255.255.0 network 192.168.0.0 broadcast 192.168.0.255 gateway 192.168.0.1 Internet works correctly, I can install packages. But it gets weird if I try to ping something I get this: PING belpak.by (193.232.248.80) 56(84) bytes of data. From 192.168.0.1 icmp_seq=1 Time to live exceeded From 192.168.0.1 icmp_seq=1 Time to live exceeded From 192.168.0.1 icmp_seq=1 Time to live exceeded From 192.168.0.1 icmp_seq=1 Time to live exceeded From 192.168.0.1 icmp_seq=1 Time to live exceeded 64 bytes from belhost.by (193.232.248.80): icmp_seq=1 ttl=250 time=17.0 ms 64 bytes from belhost.by (193.232.248.80): icmp_seq=1 ttl=249 time=17.0 ms (DUP! ) 64 bytes from belhost.by (193.232.248.80): icmp_seq=1 ttl=248 time=17.0 ms (DUP! ) 64 bytes from belhost.by (193.232.248.80): icmp_seq=1 ttl=247 time=17.0 ms (DUP! ) 64 bytes from belhost.by (193.232.248.80): icmp_seq=1 ttl=246 time=17.0 ms (DUP! ) ^CFrom 192.168.0.1 icmp_seq=2 Time to live exceeded --- belpak.by ping statistics --- 2 packets transmitted, 1 received, +4 duplicates, +6 errors, 50% packet loss, ti me 999ms rtt min/avg/max/mdev = 17.023/17.041/17.048/0.117 ms I think even more interesting are the results of pinging the router itself: stonerain@ubuntu:~$ ping 192.168.0.1 -c 1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. From 192.168.0.3: icmp_seq=1 Redirect Network(New nexthop: 192.168.0.1) 64 bytes from 192.168.0.1: icmp_seq=1 ttl=254 time=6.64 ms --- 192.168.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 6.644/6.644/6.644/0.000 ms But if I set -c 2: ... 64 bytes from 192.168.0.1: icmp_seq=1 ttl=252 time=13.5 ms (DUP!) 64 bytes from 192.168.0.1: icmp_seq=1 ttl=251 time=13.5 ms (DUP!) 64 bytes from 192.168.0.1: icmp_seq=1 ttl=254 time=13.5 ms (DUP!) 64 bytes from 192.168.0.1: icmp_seq=1 ttl=253 time=13.5 ms (DUP!) 64 bytes from 192.168.0.1: icmp_seq=1 ttl=252 time=13.5 ms (DUP!) 64 bytes from 192.168.0.1: icmp_seq=1 ttl=251 time=13.5 ms (DUP!) From 192.168.0.3: icmp_seq=2 Redirect Network(New nexthop: 192.168.0.1) 64 bytes from 192.168.0.1: icmp_seq=2 ttl=254 time=7.87 ms --- 192.168.0.1 ping statistics --- 2 packets transmitted, 2 received, +256 duplicates, 0% packet loss, time 1002ms rtt min/avg/max/mdev = 6.666/10.141/13.556/2.410 ms Pinging host machine on the other hand works absolutely correctly: no DUPs, no errors. What seems to be the problem and how can I fix it? Thank you.

  Read the article

• Slow on browsing web, but normal when using apt-get

  - by Arif Setyawan

  I have a problem with my fresh instalation of Ubuntu 11.10. The problem happen when i start up my browser and accessing website such google, askubuntu.com, facebook and other sites. frustate on the situation i try watch the progress in system monitor. the result from monitor shows that there is no data transfer when i try to accessing the page. firstly, i assume that it is the trouble from my ISP or my home connection. But it is not. When i try pinging google it shows transaction between my computer and the network but still null from browser. Then i tried to test the aptitude and it was work fine but still the browser won't recieve any packet from the internet. Here is the detail of my tools : Laptop : Toshiba Satellite e205 (network card atheros) Operating System : Ubuntu 11.04 dual booted with Win7 Browser : Mozilla Firefox comes up with the Ubuntu 11.10 installation Chrome : Last version (just yesterday install it) Thank You before :) [this question posted via win]

  Read the article

• /etc/network/interfaces doesn't always take affect

  - by user1221444

  For some reason my eth0 does not have internet on reboot sometimes. I am using a static ip. I can ping my gateway, but I am unable to ping dns servers, or anything out of my network. It seems that when my internet does work(Usually but just restarting enough times), my /etc/resolv.conf has a nameserver in it. It is empty when I have no internet access. I believe something is overwriting my interfaces settings sometimes on boot. Any help would be appreciated. I am running Ubuntu Server 12.04 64bit /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 173.213.192.234 netmask 255.255.255.248 network 173.213.192.232 broadcast 173.213.192.239 gateway 173.213.192.233 dns-nameservers 8.8.8.8 auto eth1 iface eth1 inet static address 10.0.0.106 netmask 255.255.255.0 gateway 10.0.0.1

  Read the article

• No Wireless In Ubuntu 13.10 (maybe Need Wireless Driver) [duplicate]

  - by viktorhubinette

  This question already has an answer here: No Wireless In Ubuntu 13.10 2 answers hi after updating to ubuntu 13.10 i cant see the wireless networks on the network meny so what should i do ? tell me some commands you need to see to solve the problem. Thanks (i maybe need a wireless driver becouse i installed one when i haved 12.04 becouse i could not connect to wireless before too) i cant connect to wireless that my problem so what do i need to do to get this wireless working again? some outputs lsmod | grep rt1 nothing sudo modprobe rt18192cu FATAL: Module rt18192cu not found. iwconfig eth0 no wireless extensions. lo no wireless extensions. sudo iwlist wlan0 scan wlan0 Interface doesn't support scanning. rfkill list all nothing

  Read the article

• Turn-based Client-Server Card Game - Unicast (TCP) or Multicast (UDP)

  - by LDM91

  I am currently planning to make a card game project where the clients will communicate with the server in a turn-based and synchronous manner using messages sent over sockets. The problem I have is how to handle the following scenario: (Client takes it turn and sends its action to server) Client sends a message telling the server its move for the turn (e.g. plays the card 5 from its hand which needs to placed onto the table) Server receives messages and updates game state (server will hold all game state). Server iterates through a list of connected clients and sends a message to tell of them change in state Clients all refresh to display the state This is all based on using TCP, and looking at it now it seems a bit like the Observer pattern. The reason this seems to be an issue to me is this message doesn't seem to be point-to-point like the others as I want to send it to all the clients, and doesn't seem very efficient sending the same message in that way. I was thinking about using multicasting with UDP as then I could send the message to all the clients, however wouldn't this mean that the clients would in theory be able to message each other? There is of course the synchronous aspect as well, though this could be put on top of the UDP I guess. Basically, I would like to know what would be good practice as this project is really all about learning, and even though it won't be big enough to encounter performance issues from this I would like to consider them anyway. However, please note I am not interested in using message oriented middleware as a solution (I have experience with using MOM and I'm interested in considering other options excluding MOM if TCP sockets is a bad idea!).

  Read the article

• Best way to implement mouse-based movement in MMOG

  - by fiftyeight

  I want to design an MMO where players click the destination they want to walk to with their mouse and the character moves there, similar to Runescape in this manner. I think it should be easier than keyboard movement since the client can simply send the server the destination each time the player clicks on a destination. The main thing I'm trying to decide is what to do when there are obstacles in the way. It's no problem to implement a simple path-finding solution on the client, the question is if the server will do path-finding as well, since it'll probably take too much Computation power from the server. What I though is that when there is an obstacle the client will send only the first coordinate it plans to go to and then when he gets there he'll send the next coordinate automatically. For example if there is a rock in the way the character will decide on a route that is made of two destinations so it goes around the rock and when it arrives at the first destination it sends the next coordinate. That way if the player changes destination is the middle he won't send unnecessary information. Is this a good way to implement it and is there a standard way MMOGs usually do it? EDIT: I should also mention that the server will make sure all movements are legal and there aren't any walls in the way etc. In the way I wrote it should be quite easy since all movements will be sent in straight lines so the server will just check there aren't any obstacles along that line.

  Read the article

• 1000baseT/Full Supported and Advertised but not working!

  - by user11973

  Hello, i'm using a AT3IONT-I motherboard with integrated card. If I ethtool it to 1000 full duplex it wont work! Here is sudo ethtool eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHYAD: 0 Transceiver: internal Auto-negotiation: on MDI-X: Unknown Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000033 (51) Link detected: yes here is sudo lshw -C network: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: 03 serial: bc:ae:c5:8b:7d:33 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8168 driverversion=8.021.00-NAPI duplex=full ip=192.168.0.2 latency=0 link=yes multicast=yes port=twisted pair speed=100MB/s resources: irq:42 ioport:e800(size=256) memory:f8fff000-f8ffffff memory:f8ff8000-f8ffbfff memory:fbff0000-fbffffff And lspci -nn: 00:00.0 Host bridge [0600]: nVidia Corporation MCP79 Host Bridge [10de:0a82] (rev b1) 00:00.1 RAM memory [0500]: nVidia Corporation MCP79 Memory Controller [10de:0a88] (rev b1) 00:03.0 ISA bridge [0601]: nVidia Corporation MCP79 LPC Bridge [10de:0aad] (rev b3) 00:03.1 RAM memory [0500]: nVidia Corporation MCP79 Memory Controller [10de:0aa4] (rev b1) 00:03.2 SMBus [0c05]: nVidia Corporation MCP79 SMBus [10de:0aa2] (rev b1) 00:03.3 RAM memory [0500]: nVidia Corporation MCP79 Memory Controller [10de:0a89] (rev b1) 00:03.5 Co-processor [0b40]: nVidia Corporation MCP79 Co-processor [10de:0aa3] (rev b1) 00:04.0 USB Controller [0c03]: nVidia Corporation MCP79 OHCI USB 1.1 Controller [10de:0aa5] (rev b1) 00:04.1 USB Controller [0c03]: nVidia Corporation MCP79 EHCI USB 2.0 Controller [10de:0aa6] (rev b1) 00:06.0 USB Controller [0c03]: nVidia Corporation MCP79 OHCI USB 1.1 Controller [10de:0aa7] (rev b1) 00:06.1 USB Controller [0c03]: nVidia Corporation MCP79 EHCI USB 2.0 Controller [10de:0aa9] (rev b1) 00:08.0 Audio device [0403]: nVidia Corporation MCP79 High Definition Audio [10de:0ac0] (rev b1) 00:09.0 PCI bridge [0604]: nVidia Corporation MCP79 PCI Bridge [10de:0aab] (rev b1) 00:0b.0 RAID bus controller [0104]: nVidia Corporation MCP79 RAID Controller [10de:0abc] (rev b1) 00:0c.0 PCI bridge [0604]: nVidia Corporation MCP79 PCI Express Bridge [10de:0ac4] (rev b1) 00:10.0 PCI bridge [0604]: nVidia Corporation MCP79 PCI Express Bridge [10de:0aa0] (rev b1) 00:15.0 PCI bridge [0604]: nVidia Corporation MCP79 PCI Express Bridge [10de:0ac6] (rev b1) 03:00.0 VGA compatible controller [0300]: nVidia Corporation ION VGA [10de:087d] (rev b1) 04:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 03) If i use Code: sudo ethtool -s eth0 speed 1000 duplex full autoneg off then in ethtool speed is Unknown and it doesn't work; if I set it via pre-up it wont work either... Please help!! Thanks!

  Read the article

• Intermittent ethernet connectivity

  - by Amey Jah

  I am facing a weird problem. I am connecting to my dsl modem via ethernet. After booting, sometimes Ubuntu 10.10 does not detect the eth0 card properly or does not connect to the modem. I have made the following observations: My modem is fully on. All indicators are on except ethernet, which is blinking continuously. My network indicator applet informs me that I am connected to modem, but I am not able to browse as it has not established connection with modem. I need to power off and on (restart) the modem several times OR disconnect/connect (via network applet) several times, before the system can establish a connection with the modem. Once it establishes the connection, the ethernet LED (on modem) stops blinking and glows continuously. However, I do not see this problem every time I reboot or start my computer. 3/5 time, it connects to the modem in a single attempt. Friends, I am not able to understand root cause of this problem. Plus I do not know what kind of logs should be attached. If you want any logs please give me command to run, and I will paste the result for you. Note: I ran system testing when above problem happened. Follow this link to download result.

  Read the article

• Use same dns server for all (future) connections

  - by kleofas

  I'm wondering if it is possible to specify, that all connections (even future, like when using wifi at some other place (=different SSID)) will be using pre-defined DNS server When I have some (concrete) connections, I could go to IPv4 settings, and specify DNS server there (however, in case of new connection I would have to do it (and not forget it)) This may be particularly useful for some safe/filtering dns (such as opendns's 208.67.222.123 & 208.67.220.123)

  Read the article

• Use hotplug and turn on/off PCI device for replacing NIC

  - by Ryota Hashimoto

  How can I turn off the PCI slots and change the device (especially NIC) without shutting the server down? I found a similar question (How do I turn off PCI devices?) but there are no /sys/bus/pci/slot and no files in /sys/bus/pci/slots. I'm using 12.04 LTS. $ uname -a Linux d1-c1-r1-p1 3.2.0-38-generic #61-Ubuntu SMP Tue Feb 19 12:18:21 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux $ lspci | grep Eth 04:00.0 Ethernet controller: Intel Corporation I350 Gigabit Network Connection (rev 01) 04:00.1 Ethernet controller: Intel Corporation I350 Gigabit Network Connection (rev 01) 09:00.0 Ethernet controller: Intel Corporation 82599EB 10-Gigabit SFI/SFP+ Network Connection (rev 01) 09:00.1 Ethernet controller: Intel Corporation 82599EB 10-Gigabit SFI/SFP+ Network Connection (rev 01) $ ls /sys/bus/pci/ devices/ drivers_probe slots/ drivers/ rescan uevent drivers_autoprobe resource_alignment $ ls /sys/bus/pci/devices/0000\:04\:00.0/ broken_parity_status driver modalias rescan subsystem class enable msi_bus reset subsystem_device config firmware_node net resource subsystem_vendor consistent_dma_mask_bits irq numa_node resource0 uevent device local_cpulist power resource2 vendor dma_mask_bits local_cpus remove resource3

  Read the article

• How to prevent WLAN connection from dropping permanently?

  - by Chris

  I have a desktop with a Fritz USB WLAN N stick and tried Ubuntu 12.04. Installation went fine and WLAN is working. However, connection drops permanent. Reconnecting manually fixes it but after a few minutes it drops again. It's connected to a Vodafone 802 box with WLAN N fix set. It seems that it works when I switch off N mode. But I need to test. Can someone confirm this issue or is there another solution? I have another machine with 12.04 (HP 625 laptop) running where connection is stable.

  Read the article

• dhcp configuration not working ubuntu 11.10

  - by Vivek Pradhan

  I am usually behind a proxy server in college so I connect to the ethernet or wifi using manual IPv4 addresses only inside college. I have been trying really hard to get the internet work at home, there is no proxy and I have set the network to use automatic dhcp. It seems like it is not able to connect to the port, It gets disconnected after some time automatically and then tries to reconnect. The same thing is happening with wifi networks also, after some time i see a pop up asking for authentication and ultimately its not able to connect. What might be the problem here. I looked up some similar questions and checked the /etc/network/interfaces file and looks like this: auto lo iface lo inet loopback I have no idea what those lines mean but there is no configuration for eth0 or wlan0. Any help is deeply appreciated. Ubuntu loses it charms due to these small glitches.

  Read the article

• Sending state diffs (deltas) and unreliable connections

  - by spaceOwl

  We're building a realtime multiplayer game, in which each player is responsible for reporting its state on every iteration of the game loop. The state updates are broadcasted using unreliable UDP. To minimize state data sending, we've come up with a system that will send only deltas (whatever state data that was changed). This method however is flawed, since a lost packet will mean that other players will not receive the delta, making the game behave in an unexpected way. For example: Assume that state is comprised of: { positionX, positionY, health } Frame 1 - positionX changed --> send a packet with positionX only. Frame 2 - health changed // lost ! Frame 3 - positionY changed --> send a packet with positionY only. // Other players don't know about health change. How can one overcome this issue then? sending the entire data is not always feasible.

  Read the article

• 12.04 - why does the network icon dissapear every time my machine is turned off

  - by Howard Walker

  After spending an hour or two working out how to find the network Icon, I find that when I reboot the machine, I have to go through the whole procedure again. 1. The network menu is not there - so first I have to find the terminal. This has no particular location that I can find but usually I have to type terminal in the dash. 2. Then I have to type nm-applet in terminal 3. The network manager icon then appears, but only works if the terminal window remains open. Shut down the terminal window and the network disappears. This is a pain - plus I have to type my password in every time, which is another waste of time, thought this has always been a problem. So can anyone tell me how to make the web automatically connect at startup without any intervention from me.

  Read the article

• How do I airport-utils to configure my Airport Extreme?

  - by chands

  I'm trying to use this package (airport-utils) to try to configure my Airport Extreme. I was able to install it without a problem using apt-get but when I try to use it nothing happens. Literally, nothing: shreyas@shreyas-laptop:~$ airport2-portinspector shreyas@shreyas-laptop:~$ No windows open, nothing. I tried calling ps aux and grepping for anything that might hint to the command actually doing something but I came up empty. Does anyone have any experience with this package and can help me, or is there something else I can do to work with my Airport Extreme?

  Read the article

• TCP port are filtered in VirtualBox

  - by iUngi

  I'm running Ubuntu using VirtualBox to test a server application, but I couldn't get it work the communication. I used nmap to check whether the port is open or not: nmap -T4 -n vbip -p 30000 Host is up (0.00061s latency). PORT STATE SERVICE 30000/tcp filtered unknown when I'm checking the port inside the VirtualBox, than the port is open Host is up (0.00061s latency). PORT STATE SERVICE 30000/tcp open unknown I'm using bridge connection, does the VB filter the ports?

  Read the article

• A "tinkered" PC can ping by IP, not by hostname. How to fix?

  - by aitchnyu

  Like this: root@tis-server:~# ping www.google.com ping: unknown host www.google.com root@tis-server:~# ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_req=1 ttl=55 time=50.3 ms 64 bytes from 8.8.8.8: icmp_req=2 ttl=55 time=65.4 ms It was tinkered by somebody else and I (and him!) cant trace his actions. The graphical connection manager also refuses to work thanks to the tinkering. It also makes route add default gw 192.168.0.1 necessary for each reboot to atleast ping by IP. How do I fix this? It is Ubuntu 11.10 As requested: Output of ifconfig: eth0 Link encap:Ethernet HWaddr 48:5b:39:ae:21:98 inet addr:192.168.0.100 Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::4a5b:39ff:feae:2198/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13194 errors:0 dropped:0 overruns:0 frame:0 TX packets:5156 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1420596 (1.4 MB) TX bytes:827295 (827.2 KB) Interrupt:42 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4817 errors:0 dropped:0 overruns:0 frame:0 TX packets:4817 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:377732 (377.7 KB) TX bytes:377732 (377.7 KB) Output of resolv.conf: Output of /etc/network/interfaces: GNU nano 2.2.6 File: /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.0.100 netmask 255.255.255.0

  Read the article

• gnome-file-share-properties doesn't work

  - by Riccardo Magrini

  I've configured gnome-file-share-properties on all my Ubuntu's PC for sharing the directory Public to each other. I following some guide found on Internet for the configuration of it, all explain the same procedure but in my case I don't see any Public directory shared with the PC. Following this link http://library.gnome.org/users/gnome-user-share/stable/gnome-user-share-getting-started.html.en I'd see the directory Public plus the name of PC that shares its directory on Nautilus Places. In my case I don't see anything, therefore on the Network place see all the machines 'n if I try to click on one receive this: "DBus error org.freedesktop.DBus.Error.NoReply: Message did not receive a reply (timeout by message bus)" note: I don't want to use Samba because I've all Ubuntu PC, and the firewall is disabled on all PC.

  Read the article

• Network sharing for android

  - by Shagun

  I am on ubuntu 12.04 and I want to create a wifi hotspot to be used with my android device. Now I know there are so many tutorials available every where and that I have all options in network tab to use but I couldn't get it to work. Android does not work with an adhoc connection and whatever wifi network I created, my android device could not connect to it (I could connect a phone using bada to it and other computers can also be connected) I know the work around to get android on a adhoc connection but can't I have some thing as simple as connectify for windows? PS : I am not looking for workarounds involving android.

  Read the article

• Procedural object generation and unique identification

  - by 2080

  My question relates to procedural content generation and data management of the emerging objects in a database. I assume a networked game, with a server-client model. Unspecified objects in the game world are generated while the game is running with procedural algorithms (for example perlin noise). The players (/clients) can modify the properties of these objects, but have to notify the server of these changes. How could this communication address unique objects, so that both the server and the client know of which object they are speaking? Not only the inner properties of the objects can differ, but also visible, such as the position. When the player wants to select one of these objects the game has to find out the id - does anyone know which methods or algorithms can accomplish that?

  Read the article

• How to install Netgear N-300 UAB adapter WNA3100 on Ubuntu 12.04

  - by JacobusR

  After a fresh install of Ubuntu 12.04, the first thing I'm trying to do, is to setup my wireless adapter. I can see it using lsusb: beer@beer-linux:~$ lsusb ... Bus 002 Device 006: ID 0846:9020 NetGear, Inc. WNA3100(v1) Wireless-N 300 [Broadcom BCM43231] ... I have found a lot of dated instructions on the net and just wanted to know what the right way is to set it up on 12.04. I don't want to mess up a brand new install by tweaking things that don't need tweaking. According to most posts, you have to install the Windows drivers using the ndiswrapper package. Is this still the right way to go? If so, it would be great if someone could write down the steps to do this under 12.04

  Read the article

• Wifi networks will not show up!

  - by Kcahmadi

  I'm running Ubuntu 14.04 on an old '08 macbook. I've gone to system settingsSoftware & UpdatesAdditional Drivers and enabled the wireless driver. But when I click the wifi icon on the top toolbar no networks show up. When running lshw it clearly shows my wireless card under Network controller and it says the driver is installed. However, nm-tool only shows ethernet. And rfkill only shows bluetooth. What can I do?

  Read the article

• Connecting to VPN / proxy with different port number

  - by user779159

  I have an IP address, port, username, and password for one of those VPN / proxy services that allows you to use an IP address other than what your ISP gives you, but in the 'Edit Connections VPN' GUI I don't see where to enter a port. I enter the IP address under 'Gateway' and the username and password where it asks for it, but it doesn't work. I try to enter it with the IP address ending with a colon, followed by the port, but that doesn't work either (e.g. "1.1.1.1:9999"). Any idea how I could make it work? I'm using Ubuntu 12.04 LTS. Thanks.

  Read the article

• Bridge Laptop's Ethernet to Wireless

  - by Kalphiter

  The laptop wirelessly connects to my router, while the desktop is connected to the laptop with an ethernet wire. The desktop successfully can use the internet if I set the connection to be shared on the laptop. The problem is, I need the laptop to forward the desktop's packets across the link unmodified, so the desktop is on the same network as the router. The desktop needs its IP assigned by the router, so that I can access it from another computer as "192.168.1.8".

  Read the article

• How to direct Ubuntu to use USB connection for Internet

  - by t3ch

  Hi folks, I posted yesterday regarding how to configure easytether on Ubuntu. I followed the steps and everything looks good from the terminal. But I am not able to connect to the Internet. Currently I am connected to a Wireless network, I tried disconnecting to it, in hope to connect to Internet using my phone but with no help. How do I make my notebook use my cell phone's connection. I have attached the snapshot from the terminal.

  Read the article

< Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >