Search Results

Search found 7875 results on 315 pages for 'wired networking'.

Page 54/315 | < Previous Page | 50 51 52 53 54 55 56 57 58 59 60 61  | Next Page >

• How do I get my RTL8192ce based wireless device working properly?

  - by JonnyTruelove

  I am using the rtl8192cu chipset (on a Belkin wireless USB adapter N300) combined with 64 bit architecture and the 3.8 kernel. Some of you may know that this doesn't work. I tried this fix - RTL8188CU USB Network Adaptor on ubuntu 13.04 and now my internet is super slow. I am totally new to Ubuntu and I am concerned I do not have the right driver. The "stock" driver was the RTL8192cu, but it didn't connect 99% of the time and if it did the upload speed was higher than the download. Right now I am connecting through my laptop with a crossover cable, so my internet connection is just fine in my apartment. Relevant output from lsusb is here: Bus 002 Device 002: ID 050d:2103 Belkin Components F7D2102 802.11n N300 Micro Wireless Adapter v3000 [Realtek RTL8192CU] (bonus question: is that [050d:2103] the actual physical address straight from the hardware? Or does it change when I put different drivers on it? I am concerned I do not have the right driver)

  Read the article

• My internet connection slows or dies unexpectedly

  - by genesis

  I installed Ubuntu 10.04 once again and I'm having some problems which I had before, but I have no idea how I solved them. On Windows, everything's working fine and I had no problems with this. My problem is that sometimes, when browsing through the internet, webpages just start to load really slow, sometimes it doesn't load anything at all (Error 118 (net::ERR_CONNECTION_TIMED_OUT): The operation timed out.) and it starts to work after few minutes. My IPv4 settings are automatic (DHCP), and IPv6 settings are Ignored/Disabled. I think my previous problems had something to do with IPv6, but I'm not sure. Is there a fix for this? iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Fsite1" Mode:Managed Frequency:2.442 GHz Access Point: C8:3A:35:40:43:68 Bit Rate=0 kb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on Link Quality=43/70 Signal level=-67 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0

  Read the article

• Internet stopped working suddenly on 12.04

  - by Daniel

  My laptop was running smoothly until yesterday. Today, I can't connect to the Internet at home anymore. I am only able to access the router, but no Internet access. A have a Dell Latitude E6320 with Ubuntu 12.04. At my job, I don't have any problems connecting this laptop both via Wireless and Ethernet. At home, if I try connecting it through Windows, it does work fine. I even checked the MAC address and it's OK. My other laptop, which also runs Ubuntu, is not facing this problem. I have already tried to restart and downgrade network-manager package and its dependencies. Can anyone help me please? I am afraid, I will have to reinstall everything.

  Read the article

• unreachable subnet in one direction

  - by Carl Michaud

  I'm unable to route traffic to a subnet in my home. Here's my topology: INET <- Router A <- Router B <- WIFI AP where: Router A - ARRIS TG862G/CT (from comcast) - WAN DHCP, LAN 10.0.0.99 Router B - Linksys WRT400N with DD-WRT - WAN 10.0.0.12 , LAN 10.0.1.1 I was able to use DD-WRT to configure a static route for the 10.0.1.x network back to the 10.0.0.x network. But I'm not sure if i can do the reverse on the ARRIS router and was looking for suggestions on how to fix that. I've set things up this wasy because I am using OpenDNS to mange internet content for my kids and of course I wasn't able to configure DNS to my liking on Router A either. So at present I'm using Router A on 10.0.0.x to provide a private unfiltered WIFI AP (no ssid broadcast) that I use for netflix only and then I use router B to provide a filtered WIFI AP for the rest of my WIFI devices on 10.0.1.x. However I would like to be able to connect to my 10.0.1.x devices from the internet via dynamic dns; but I can't see anything behind router B this way. Thoughts?

  Read the article

• ubuntu nic card issue

  - by Blainer

  I am trying to install NIC r8168 and it shows everything installed ok. It is a brand new NIC and the lights wont come on when I plug in a ethernet. The NIC is that is not working is eth0. Why does it show the r8168 driver being used by 0? My NIC model number is ST1000SPEX if anyone is wondering. lsmod Module Size Used by r8168 215669 0 ifconfig eth0 Link encap:Ethernet HWaddr 00:0a:cd:1e:0a:4a UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 Base address:0x2000 eth1 Link encap:Ethernet HWaddr 00:19:d1:1d:f6:7a inet addr:192.168.1.83 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::219:d1ff:fe1d:f67a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:551467 errors:0 dropped:0 overruns:0 frame:0 TX packets:145219 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:409744342 (409.7 MB) TX bytes:12233173 (12.2 MB) Interrupt:21 Memory:dfde0000-dfe00000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:280 errors:0 dropped:0 overruns:0 frame:0 TX packets:280 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:22608 (22.6 KB) TX bytes:22608 (22.6 KB) Ubuntu 11.10 x64 Kernel 3.0.0-12-generic

  Read the article

• Client side prediction/simulation Question

  - by Legendre

  I found a related question but it doesn't have what I needed. Client A sends input to move at T0. Server receives input at T1. All clients receive the change at T2. Question: With client-side prediction, client A would start moving at T0, client-side. All other clients receive the change at T2, so to them, client A only started moving at T2. If I understand correctly, client B will always see client A's past position and not his current position? How do I sync both client B and client A?

  Read the article

• ubuntu 12.04 server doesn't resolve local domain name

  - by jdog

  After apt-get upgrade this morning, my Ubuntu 12.04 web server does no longer resolve a domain name hosted on it. I also received the error message: "resolvconf: Error: /etc/resolv.conf isn't a symlink, not doing anything." I found this question Network Manager not populating resolv.conf but the solutions provided there did not resolve the problem. Creating the symlink in fact caused websites to load very slowly, so I assume there is some sort of (reverse?) DNS lookup not working, when I create the symlink.

  Read the article

• Wireless connected but internet not working, modem is fine because I'm typing over wifi on my android

  - by Sandro Livaja

  I can't connect to the Internet in 11.10. I tried switching my wifi card to another USB slot but nothing changed. Is it possible that the card is able to connect while not being able to receive packages? $ ifconfig eth0 Link encap:Ethernet HWaddr 40:61:86:35:11:b0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 Base address:0x6000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 74:ea:3a:8c:d5:5c inet addr:192.168.2.5 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::76ea:3aff:fe8c:d55c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1209 (1.2 KB) TX bytes:15329 (15.3 KB)

  Read the article

• Wireless ad-hoc network between Ubuntu and MS Windows

  - by nixnotwin

  I have setup a wireless ad-hoc connection between two laptops: one running ubuntu and the other MS XP. I have assigned static IP to both the laptops and both get connected quite easily. I can access all ubuntu services like ssh, squid, samba from the laptop running MS Windows. But from Ubuntu machine I cannot access any Windows services like shared directories etc. The Windows machine doesn't even respond to ping requests from ubuntu.

  Read the article

• How do I re-install Samba?

  - by Sheldon

  I recently followed a guide to configure Samba but I couldn't get it configured properly. After realizing that the guide was six years out of date I thought I should start again. I reinstalled samba by first using these commands: sudo apt-get purge samba sudo apt-get install samba But after reading my configuration file (/etc/samba/smb.conf) I noticed that it was the same file, containing the same edits I had made. I then proceeded to delete the directory and then re-install samba again. However, the directory is not replaced after re-instillation and now I don't appear to have a configuration file. How do I get it back? Or install Samba correctly?

  Read the article

• Advice on how to understand in general and in practice IT Infrastructure

  - by Luca

  My IT knowledge resides mainly in SW development. I have just some basic know how about networks. On the net I tried to get information and read books in order to better understand the overall IT infrastrcuture, but all the sources I found are too generic or, mainly, too detailed in just one aspect, making me lost. Could anyone suggest some books or web resources as good compromise in details? My goal would be able to understand the network issues and security threats when, for example, two remote system have to be setup and put in connection each other. Considering this scenario there are several aspects to consider: firewalls, intranet/internet interconnections, certificates for httpS, etc. The argument is quite wide, therefore I was looking for something that might help to start to understand this subject without going too deep in details (Computer Networks from A.Tanenbaum is a wonderful milestone, but way too specific for my scope). Thanks

  Read the article

• Multicast in Ubuntu

  - by iwant2learn

  Can some one please explain the steps required to configure a multicast in Ubuntu? I have a simple program taken from Internet. I get errors when I execute the client program. I get the error as: Opening datagram socket....OK. Setting SO_REUSEADDR...OK. Binding datagram socket...OK. Adding multicast group error: No such device: When I execute the server program I get the error as: Opening the datagram socket...OK. Setting local interface error: Cannot assign requested address I am using Ubuntu to run the program. I have two different laptops but connected via the same network. I am using wireless network to perform the above operation.

  Read the article

• How to create shared home directories across multiple computers?

  - by Joe D

  I know there are ways to share a folder across computers making it easy to move files. But I was wondering how one would setup a single login which lets you access the same files regardless of which machine you login on? What I would like is something similar to something you would see in a college campus where students login on machines in the lab and see their files regardless of which machine they use. I know there are server involved here. I have a need to create this on a smaller scale where we have a few computers available (and one of these could act as the server if needed and host the files) that every one shares. Note, the specific install of software might be different on each computer but the login and OS are the same. Since some computers have additional capability that our group members will need to use at rotating schedules (software licenses or hardware components, etc.). I have not done this before, so I would appreciate detailed instructions if possible or a reference to a guide that describes this. Thanks in advance.

  Read the article

• Ubuntu Desktop on PC as an IPv6 router?

  - by Cliff

  I have a DELL PC with Ubuntu 12.10 and a pandaboard running the latest linaro ubuntu 12.08. The Ethernet on the panda board is reporting 'no ipv6 router present' regardless of what router I connect (they are all probably not ipv6). I can connect via a cross-over Ethernet cable the pandaboard to the DELL PC. Can I setup the DELL PC to act as an IPv6 router. the PC has a wireless connect to our router/ADSL box. I would Really appreciate some help here so if you have an alternative please suggest it.

  Read the article

• How to set up an ethernet and wireless network using /etc/network/interfaces?

  - by den-javamaniac

  Hi. Currently I have ethernet and wireless networks configured through a network manager (further NM) but it seems to be a bit buggy (I need a different MAC for ether which is never applied if using NM), so I would like to move all the network configs to interfaces file. I know (or can google for) configuration code, but I'm not sure how NM works and it looks like it overrides interface config. Please advice, how I can handle this issue. NOTE: I also would like to be able to locate and connect to various wireless networks but not sure how to do it.

  Read the article

• Can't ping external websites

  - by Frantumn

  I can't ping google.com with my virtual ubuntu 12.04 server. I have set up a proxy URL in my /etc/apt/apt.conf file and it says Aquire::http::proxy http://urlname.com:9999; Now, I don't know a lot about how the proxy works, but I do know when we use it on windows VMachines it's a pac script that we place in internet explorer LAN settings and it automatically detects the script and gives internet access. I tried including the 9999/proxy.pac in the apt.conf URL and it didn't seem to work any better. Would ubuntu know how to handle a proxy.pac assuming it was created for windows? Should my URL include the .pac or just end after the port numbers? I've tried both without sucess, but I would like to know. A quick test to ping a fellow co-workers' PC was sucessful. So I can see network computers, but not google. or other internet sources.

  Read the article

• Disabling IPv6 on a single interface

  - by ijw

  I'm slightly weirded out by the fact that Ubuntu won't process ipv4 DHCP unless you explicitly tell it to, but will happily take ipv6 RAs unless you tell it not to. Is there any way to change the default behaviour to be 'do nothing unless I explicitly turn it on'? (Note to answerers: I'm not looking to globally disable ipv6, or completely turn off autoconf. I'm looking to disable autoconf by default (as in, I don't want ipv6 unless I say so in /etc/network/interfaces, in the same way that I don't just get a v4 address unless I've explicitly turned on dhcp). What's happening is that, for any interface that's up - e.g. has an ipv4 config - a v6 address tends to just turn up on the interface as well, despite the fact that I've not enabled that explicitly. The solutions to date are fine as far as they go, but if I disable v6 or autoconf globally, I can't then re-enable v6 on a per-interface basis with a simple command in /etc/network/interfaces. I'm fairly sure I'm asking for the moon on a stick, mind you.)

  Read the article

• Start & Stop internet connexion without broking Network Manager

  - by user3634569

  I am on Precise. I used this command (with an alias), to close the network, dbus-send --system --print-reply --reply-timeout=120000 --type=method_call --dest=org.freedesktop.NetworkManager /org/freedesktop/NetworkManager org.freedesktop.NetworkManager stop it worked, now I have to use dbus-send --system --print-reply --reply-timeout=120000 --type=method_call --dest=org.freedesktop.NetworkManager /org/freedesktop/NetworkManager org.freedesktop.NetworkManager.Sleep boolean:true it work but not so well, sometimes I can't restart the network and NetworkManager is blocked too and strange errors even GUI freeze . What I need is a command line which close the network and don't mess with Network Manager, maybe with the routing table or what else.

  Read the article

• Ubuntu 12.04 Network Manager: unable to save manual setting to set up a static ip

  - by Andy

  I am fairly familiar with setting up servers, and ubuntu is generally my flavor of choice, but I just installed 12.04 desktop and I am seeing some behavior in network manager that is really puzzling. The network connection works fine if I leave it set on dhcp, but I would like a static IP address for my new web server. When I go into network manager and edit the connection for the one and only NIC I can select MANUAL from the dropdown menu but as soon as I do the Save button becomes greyed out. Even after filling out all fields for the connection it is still grey and I am unable to save the static IP connection information. Any thoughts would be greatly appreciated. I'm hoping there is just some new setting that I am unaware of.... On another note, if I stop the network manager and go edit the interfaces file (and the appropriate hosts/routes/dns files), I do get a static ip address assigned and I can contact my server from the outside, however, the server cannot find the internet. Can't ping even its own ip... I can ping the loopback interface though. I'm really confused on this one. Hoping someone can offer some help.

  Read the article

• connecting ubuntu with 7 via network cable

  - by VeXe

  i was tryin to connect my ubuntu toshiba satalite L650 laptop with my desktop via a network cable so that i can share things and remotely control the desktop from the laptop, i googled the problem out and found a guide page , i followed all the steps , i installed samba, i had the two computer have the same workgroup name , i had everything correct, but i still dont see connection estbalished between the two computers, (neither one is visible to the other) what is missing ? thanx in advance.

  Read the article

• How to connect ethernet on ubuntu (with auto-detection by Ubuntu)

  - by user12285

  Do I need to post another thread for the same? If so, sorry. Yes, I saw that it's been well over six months but I have the same router SmartAX MT880d with ethernet, and the exact same problem, that is no internet even though I can successfully reach the modem settings page by entering 192.168.1.1 in Firefox. Sorry if I don't use the right (technical) terminology to express my issue. English is not my mother tongue. I'm a total beginner with ubuntu. My internet works great in Windows but does not work in Ubuntu. For 2 weeks, I've kept reading on the web and forums and the ubuntuguide.org to name a few but to no avail. Now I see no other solution but to ask for help. My problem is that as a beginner, I can't find a way to put the right digits in the right place because I don't know what numbers I need to put in what files (eg: do I need to use DHCP? or a static IP address? No clue whatsoever. I'm confused between putting figures in the wrong spaces. For example, is the modem/router's IP exactly 192.168.1.1 for Huawei Smart AXMT880d modem?? Is the subnet 255.255.255.0? Gateway 192.168.1.1. I'm confused as I can also see a different IP starting with 155131*** (is it an account number? no clue again) on my contract with Huawei (a Chinese ISP). Apart from calling 911, what other numbers do I need to put in and where? How do I check that all the numbers have been entered correctly in every appropriate space before trying to connect the Internet?

  Read the article

• Scuttlebutt Reconciliation from "Efficient Reconciliation and Flow Control for Anti-Entropy Protocols"

  - by Maus

  This question might be more suited to math.stackexchange.com, but here goes: Their Version Reconciliation takes two parts-- first the exchange of digests, and then an exchange of updates. I'll first paraphrase the paper's description of each step. To exchange digests, two peers send one another a set of pairs-- (peer, max_version) for each peer in the network, and then each one responds with a set of deltas. The deltas look like: (peer, key, value, version), for all tuples for which peer's state maps the key to the given value and version, and the version number is greater than the maximum version number peer has seen. This seems to require that each node remember the state of each other node, and the highest version number and ID each node has seen. Question Why must we iterate through all peers to exchange information between p and q?

  Read the article

• All my bandwidth eaten up - report included

  - by Mel

  I have my network bandwidth eaten up totally. Whenever I connect my network, without any application being opened it is always full. I have prepared report of iftop, nethogs and network system monitor. iftop and nethogs My host IP is 192.168.1.203 and all the rest are not known though I have tried to pin 192.168.1.105, it doesn't reply. If possible I would like to block the most disturbing IP which is 192.168.1.105 to block it. but don't know how.

  Read the article

• Network print to brother MFC-7420

  - by trampster

  I am trying to pint to a Brother MFC-7420 from my ubuntu 10.04 machine. The brother is attached to a windows XP machine and is shared. This is what I have tried: System-Administration-Printing, Add, Expand Network Printer, Windows Printer via SAMBA, Browse (I can find the printer no problems here), Foward, Choose Driver Dialog, Brother, My printer is not in this list So the next thing I tried was to download the printer driver from here http://welcome.solutions.brother.com/bsc/public_s/id/linux/en/download_prn.html The driver installed fine but my printer still does not appear in the list. I also tried installing the cups wrapper but that gave the following error. Restarting Common Unix Printing System: cupsd [ OK ] cp: cannot stat `/usr/share/cups/model/MFC7420.ppd': No such file or directory dpkg: error processing cupswrappermfc7420 (--install): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: cupswrappermfc7420 I tried connecting the printer directly but even though I have installed the driver, when I go to printers and click on the printer (it shows up fine as a USB printer) then it say searching for drivers and then gives me a list, this is the same list as before which doesn't have my printer. It really shouldn't be this hard. on window you don't have to installing anything it just works and the same is true for my brothers Mac. How do I print to my printer?

  Read the article

• how to find 3g modem signal strength with out AT commands?

  - by neckTwi

  when i try to find signal strength of my modem using AT+CSQ, the usb device is locked by the network manager. To find the signal strength with AT+CSQ i have to first disable network connection using #nmcli nm wwan off to unlock the device inode /dev/ttyUSBX. Is there any nmcli option to get signal strength or any other option? EDIT The gdbus object for NetworkManager don't have any method like getSignalStrength. Network manager is locking device file preventing to use AT commands. nm-applet was able to display signal strength in system tray. so there should be a way to get signal strength form network manager! nmcli is command line counter part of nm-applet. Can i get signal strength using nmcli? nothing about signal strength is mentioned in its man pages.

  Read the article

< Previous Page | 50 51 52 53 54 55 56 57 58 59 60 61  | Next Page >