Search Results

Search found 14951 results on 599 pages for 'connect by'.

Page 501/599 | < Previous Page | 497 498 499 500 501 502 503 504 505 506 507 508  | Next Page >

  • Can a USB/IDE/SATA adapter be flaky?

    - by Ward
    I use USB/IDE/SATA converters a lot and on the two that I have now, I sometimes get errors copying files to drives. It only happens when I'm copying big files to the drive (big can mean as little as 100MB, I think it happens more often with bigger files - 300MB or more), and basically the copy will fail and I'll get one or more error messages about "Delayed write failed." But if I disconnect the drive and re-connect it, I'll usually be able to continue. (The file that was being copied will be corrupt, but otherwise the drive is fine.) I just noticed a new type of flakiness: the data transfer rate can vary widely. I copied one set of files (5x300MB files) and it took 10+minutes, then I copied another set (approx. the same sizes) and it took less than a minute. I haven't done systematic testing, the other things I'm doing on my laptop at the same time might have some impact, and I haven't cross-checked the two adapters I have and the 3 hard drives I'm working with to see if there's a pattern. I'm more wondering if anyone else has seen anything like this.

    Read the article

  • EC2 AMI won't boot after edit

    - by Eric Lars0n
    I did something stupid, I got a new laptop and copied everything over to the new one, then wiped the old one clean. Then I realized that I forgot to copy the private key out of .ssh that I use to connect to my AWS EBS backed instance. So I can't log in to my custom AMI. So I created a new Volume from the Snapshot of the AMI, then started up a public instance and attached the Volume to it, edit the sshd_config to allow for password log in. Unmounted the volume, detached it, made a snapshot of it, then made a new AMI from the snapshot. The new AMI launches, but never passes the Status Checks and is not reachable. What am I doing wrong? Or alternatively how can I fix my problem? Edit: Adding some of the console output Linux version 2.6.16-xenU ([email protected]) (gcc version 4.0.1 20050727 (Red Hat 4.0.1-5)) #1 SMP Mon May 28 03:41:49 SAST 2007 BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000006a400000 (usable) 980MB HIGHMEM available. 727MB LOWMEM available. NX (Execute Disable) protection: active IRQ lockup detection disabled RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize NET: Registered protocol family 2 Registering block device major 8 XENBUS: Timeout connecting to devices! Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,0)

    Read the article

  • Capabilities of business and SOHO routers

    - by Q8Y
    I'm currently studying for the CCNA certifications (especially for Cisco routers and configuration). I know that business routers provide more features than SOHO routers, the processing speed and RAM can be enough. Assume I need to connect a number of users through a network (accessing internet, share files, printers, ...). I have a high speed connection to the internet and I already applied QoS. How can I find out how many users such a single (SOHO) router could handle? In my case I'd attach to it multiple switches until I have the number of ports needed. Would everything work well and smoothly with 50 users? What about 300? At which point would I need a business router instead? If I implemented VLAN here, would it make any difference in the performance? When do I really need to use more than one router? (Both SOHO and business) I'm thinking that I may need them only if I want to increase the performance (instead of replacing the existing one) and if I have multiple locations, so in this situation I need to have multiple routers, right? Put differently: Is there is a need to have another router if my business all in one place?

    Read the article

  • Openvpn - stuck on Connecting

    - by user224277
    I've got a problem with openvpn server... every time when I trying to connect to the VPN , I am getting a window with login and password box, so I typed my login and password (login = Common Name (user1) and password is from a challenge password from the client certificate. Logs : Jun 7 17:03:05 test ovpn-openvpn[5618]: Authenticate/Decrypt packet error: packet HMAC authentication failed Jun 7 17:03:05 test ovpn-openvpn[5618]: TLS Error: incoming packet authentication failed from [AF_INET]80.**.**.***:54179 Client.ovpn : client #dev tap dev tun #proto tcp proto udp remote [Server IP] 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert user1.crt key user1.key <tls-auth> -----BEGIN OpenVPN Static key V1----- d1e0... -----END OpenVPN Static key V1----- </tls-auth> ns-cert-type server cipher AES-256-CBC comp-lzo yes verb 0 mute 20 My openvpn.conf : port 1194 #proto tcp proto udp #dev tap dev tun #dev-node MyTap ca /etc/openvpn/keys/ca.crt cert /etc/openvpn/keys/VPN.crt key /etc/openvpn/keys/VPN.key dh /etc/openvpn/keys/dh2048.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt #push „route 192.168.5.0 255.255.255.0? #push „route 192.168.10.0 255.255.255.0? keepalive 10 120 tls-auth /etc/openvpn/keys/ta.key 0 #cipher BF-CBC # Blowfish #cipher AES-128-CBC # AES #cipher DES-EDE3-CBC # Triple-DES comp-lzo #max-clients 100 #user nobody #group nogroup persist-key persist-tun status openvpn-status.log #log openvpn.log #log-append openvpn.log verb 3 sysctl : net.ipv4.ip_forward=1

    Read the article

  • Access server using IP on another interface

    - by Markos
    I am using Windows Server 2012 instead of a router for my home network. Currently I am using RRAS and computers from local network can access Internet correctly. Here is a map of the current setup: [PC1] ---| |---- (lan ip)[Server](wan ip)--> internet [PC2] ---| I have applications running on Server, such as IIS and others. All can be accessed from internet using wan ip and from lan using lan ip. I have a domain, lets say its my-domain.com, which is resolved to my wan ip. What I want is to enable my LAN computers to be able to connect to services on my server using the very same address as internet users: eg http://my-domain.com/. However this does not work for my lan computers. What I understand is that I need to set up some kind of loopback route in a way that packets comming to LAN interface get routed to WAN interface. But I haven't found how to achieve this (in fact, I don't know WHAT to search for). Feel free to ask for additional informations and I will try to update the question.

    Read the article

  • LDAP groups not applying to filesystem permissions

    - by BeepDog
    System is ArchLinux, and I'm using nss-pam-ldapd (0.8.13-4) to connect myself to ldap. I've got my users and some groups in LDAP: [root@kain tmp]# getent group <localgroups snipped> dkowis:*:10000: mp3s:*:15000:rkowis,dkowis music:*:15002:rkowis,dkowis video:*:15003:transmission,rkowis,dkowis,sickbeard software:*:15004:rkowis,dkowis pictures:*:15005:rkowis,dkowis budget:*:15006:rkowis,dkowis rkowis:*:10001: And I have some directories that are setgid video so that the video group stays, and they're configured g=rwx so that members of the video group can write to them: [root@kain video]# ls -ld /srv/video drwxrwxr-x 8 root video 208 Oct 19 20:49 /srv/video However, members of that group, say dkowis cannot write into that directory: [root@kain video]# groups dkowis mp3s music video software pictures dkowis Total number of groups that dkowis is in is like 7, I redacted a few here. [dkowis@kain wat]$ cd /srv/video [dkowis@kain video]$ touch something touch: cannot touch 'something': Permission denied [dkowis@kain video]$ groups dkowis mp3s music video software pictures I'm at a loss as to why my groups show up in getent groups, but my filesystem permissions are not being respected. I've tried making a new directory in /tmp and setting it's group permissions to rwx, and then trying to write a file in there, it doesn't work. The only time it does work is if I open it wide up allowing o=rwx. That's obviously not what I want, and I'm not able to figure out what my missing piece is. Thanks in advance.

    Read the article

  • Writing xml with powershell

    - by alex
    i have a script that get all the info i need about my SharePoint farm : [System.Reflection.Assembly]::LoadWithPartialName("Microsoft.SharePoint") > $null $farm = [Microsoft.SharePoint.Administration.SPFarm]::Local $websvcs = $farm.Services | where -FilterScript {$_.GetType() -eq [Microsoft.SharePoint.Administration.SPWebService]} $webapps = @() foreach ($websvc in $websvcs) { write-output "Web Applications" write-output "" foreach ($webapp in $websvc.WebApplications) { write-output "Webapp Name -->"$webapp.Name write-output "" write-output "Site Collections" write-output "" foreach ($site in $webapp.Sites) { write-output "Site URL --> -->" $site.URL write-output "" write-output "Websites" write-output "" foreach ($web in $site.AllWebs) { write-output "Web URL --> --> -->" $web.URL write-output "" write-output "Lists" write-output "" foreach ($list in $web.Lists) { write-output "List Title --> --> --> -->" $list.Title write-output "" } foreach ($group in $web.Groups) { write-output "Group Name --> --> --> -->" $group.Name write-output "" foreach ($user in $group.Users) { write-output "User Name --> --> --> -->" $user.Name write-output "" } } } } } } i want to make the output to an XML file and then connect the xml file to HTML and make a site of it for manager use how can i do it ? thanks for the help !

    Read the article

  • KVM Guest Reboot Loop

    - by javano
    I have been pulled into a situation where a KVM server (CentOS 6.2) lost power and upon reboot one of the guests hasn't started up again (XP SP3). I have SSH'ed in and someone must have changed something relating to the hyper visors prior to the power loss, but not rebooted all the guests. This particular guest wouldn't start because it was configured to use /usr/bin/qemu-system-x86_64 which isn't there now (assuming it was before?). I changed it to use /usr/libexec/qemu-kvm as this is what all the other guests on this server seem to be using, and its booting up. Using virt-manager on my local machine I can connect to the display of the XP machine and it gets as far as this screen; http://support.gateway.com/emachines/issues/2-1131285152-01.gif The problem I face now, is that which ever option I choose the machine just reboots. So it's and endless loop. I thought that perhaps a file system error maybe present due to the unclean shutdown. There is an XP SP3 ISO mounted under the guest, which I booted from in an attempt to access the recovery tools, but I don't have the Administrator password! I am out of ideas, and it's turning out to be quite the conundrum. Should I use a 3rd party live CD to test the FS for errors? How else can I trouble shoot these restarts?

    Read the article

  • Low-profile, PCI Express, x1 video card with VGA-out?

    - by Dandy
    I just bought an Acer Aspire EasyStore H340 system (http://us.acer.com/acer/productv.do?LanguageISOCtxParam=en&kcond61e.c2att101=54825&sp=page16e&ctx2.c2att1=25&link=ln438e&CountryISOCtxParam=US&ctx1g.c2att92=450&ctx1.att21k=1&CRC=936243954) It comes with Windows Home Server, which I don't particularly care for (too dumbed down for my liking)--I bought the box mainly for the form factor, and intend to install Server 2008 on it and have it run as a small domain controller. The geniuses at Acer however went out of their way to ensure you can only run Home Server--you can only connect to it via the Home Server Connector software, as it has no video-out whatsoever (so essentially, there's no way to even get into the BIOS). It only has a low-profile, PCI Express x1 slot. It turns out to be way harder than I thought to locate a video card that both has an x1 connector, and is low-profile (I'd really rather not snip the bracket at the back just so it'll fit the case). I know they're out there, and I've seen one with Display Port outputs, but I don't have a monitor with this connection. So to reiterate, it needs to be: - x1 connector - low profile - VGA out (though DVI would be okay; I have some spare adapters) Can anyone recommend anything at all?

    Read the article

  • Wireless signal changes from strong to weak after connecting

    - by gibberish
    Router (primary AP) is a WRVS4400N, WAP (signal booster) is a WAP4410N. Problem: User is physically located within ten feet of WAP (200 feet from main wireless router). Signal is at 5 bars as user connects to wireless network. Within seconds, signal is at or below two bars and connection is poor. Background: Trying to solve problem of weak wireless signal in back offices. Desired result is for client laptops to automatically switch to the stronger signal. WAP is connected to network via Ethernet cable. WAP is set to AP mode (instead of Wireless Repeater mode) WAP does appear to boost signal. Using Windows 7 sys tray Connect To A Network applet, can observe signal boost as laptop approaches the WAP. Above-described problem happens to users located near or beyond the WAP. It does not happen to users in close proximity to the router. Secondary Question: If using WAP in AP Mode, do WAP and Router (primary AP) need to be on the same channel?

    Read the article

  • Postfix connects to wrong relay?

    - by Eric
    I am trying to set up postfix on my ubuntu server in order to send emails via my isp's smtp server. I seem to have missed something because the mail.log tells me: Jan 19 11:23:11 mediaserver postfix/smtp[5722]: CD73EA05B7: to=<[email protected]>, relay=new.mailia.net[85.183.240.20]:25, delay=6.2, delays=5.7/0.02/0.5/0, dsn=4.7.0, status=deferred (SASL authentication failed; server new.mailia.net[85.183.240.20] said: 535 5.7.0 Error: authentication failed: ) The relay "new.mailia.net[85.183.240.20]:25" was not set up by me. I use "relayhost = smtp.alice.de". Why is postfix trying to connect to a different server? Here is my main.cf: # See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. myhostname = mediaserver alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases mydestination = mediaserver, localhost.localdomain, , localhost relayhost = smtp.alice.de mynetworks = 127.0.0.0/8 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all myorigin = /etc/mailname inet_protocols = all sender_canonical_maps = hash:/etc/postfix/sender_canonical smtp_sasl_auth_enable = yes smtp_sasl_password_maps = hash:/etc/postfix/sasl_password smtp_sasl_security_options = noanonymous Output of postconf -n: alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no config_directory = /etc/postfix inet_interfaces = all inet_protocols = ipv4 mailbox_size_limit = 0 mydestination = mediaserver, localhost.localdomain, , localhost myhostname = mediaserver mynetworks = 127.0.0.0/8 myorigin = /etc/mailname readme_directory = no recipient_delimiter = relayhost = smtp.alice.de sender_canonical_maps = hash:/etc/postfix/sender_canonical smtp_generic_maps = hash:/etc/postfix/generic smtp_sasl_auth_enable = yes smtp_sasl_password_maps = hash:/etc/postfix/sasl_password smtp_sasl_security_options = noanonymous smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes

    Read the article

  • Network Sharing Issues

    - by Mark Kramer
    I have two computers I want to have on a network share together (so the laptop can print through the desktop's printer). These are both connected to the same router. (One wired and one wireless) And they both have the same workgroup name. However, when I type "net view" in the command prompt, the only computer that shows up is the computer I type the command into. How do I get these computers to be shared with each other? Update: The tower is running Windows XP, the Laptop is running Windows 7. I have disabled the Firewall on both until I get this set up. Update 2: Typing the command net view on my desktop is acting very strangely. Noe sometimes it only shows itself on the list of computers, sometimes it shows itself and the laptop and sometimes it doesn't work at all and displays system error 6118. I typed net view into the command prompt on the Windows 7 laptop and both computers showed up, so I went to connect to the desktop from the laptop and it said the dekptop could not be found, even though it is showing up int he list of shared computers. Here are supporting pictures (these are coming from the laptop)

    Read the article

  • A very peculiar problem with an old pc and a newer laptop...

    - by user553492
    I got my old pc ( 248mb ram , 80 GB ) repaired and the tech people put XP in it .My newer laptop has UBUNTU 10.04 .now I only have one cable and one usb cord .So I connected my modem (with only one CAT5 port and 4 usb ports ) to laptop with CAT5 cable .Th internet is working fine . I also wanted to use net on older pc so I installed the usb drivers for win and it worked. But I got fed up of win xp and made a separate partition for FreeBSD which I planned to install .During the install I screwd up sumthing and now freebsd starts with a boot option with a ? mark in place of win xp .If I click on that it gives me a "NTLDR missing " msg. I tried connecting CAT5 cable between old and new pc and tried connecting my laptop with USB cable but nothing happend and then I realozed the modem doesnt have a WORKING usb driver for LINUX :( .FCUK ! .Freebsd doesnt` even detect the LAN cable if I use it for old pc . So basically I have a old pc that has FREEBSD which I can olny start and stare at the blank terminal console but works perfectly otherwise .FREEBSD was supposed to detect the LAN cable ??.And I have a laptop that has LINUX which only works if I connect it with a CAT5 cable .wtf . So what can I do with my old pc ??? any local server (if possible :( ) or some such thing ? or can u suggest any use .Im 18 and im into learning programming , coding .So I can practice it .Thankx !

    Read the article

  • Primary/secondary ethernet interfaces in Ubuntu 9.10

    - by Josh
    I have an Ubuntu 9.10 machine with three ethernet interfaces, eth0, eth1 and eth2. eth2 is connected to a private network. eth0 and eth2 are connected to two different LANs. Either one will provide access to the internet. All three networks have DHCP servers. Using Ubuntu's the default settings (And Gnome), when I boot up all the interfaces are active and my system gets three IP addresses. However any attempt to access the internet results in connection timeouts and other weirdness. I suspect that traffic is going out on one NIC (like eth0) and coming back in on another (like eth1). I'm not sure what's going on. The only way I can access the internet at the moment is to bring two of the devices down with ifdown. How can I configure eth0 as my primary interface so all trafic goes out by default on that interface, while keeping the other two active? Also, I want to make sure Avahi broadcasts properly on all three IPs so that the computers on the LAN of eth1 can still connect to myHostname.local...

    Read the article

  • ATI Firepro v4800 3 monitor support

    - by Jared275
    I have an interesting, yet very frustrating problem. I have two computers, both running win7 32 bit, and both with ATI Firepro V4800 graphics cards. Both are using the DVI port and two DP to DVI adapters to connect 3 monitors. One of them is able to display three desktops, while the other fails at enabling the third, displaying "cannot save changes" in display properties while requiring that one monitor must be disabled when making the change in CCC. I've verified that both computers have the same driver version and that both are using the same DP-DVI adapters. This articles suggests a few things to try, but none of its suggestions seem to work either. I'm kind of at my wits end, hence my posting here. If this is not an appropriate question for SU, I apologize. I admit that I am not very familiar with the differences between dual link and single link DVI, and that is something I have not verified is standardized between the two computers. Is that a possible reason one is working and the other isn't? How do I check if the DVI cable is a single link, or dual link?

    Read the article

  • How to route between 2 networks with a server with 2 network cards?

    - by LumenAlbum
    This is the first time I am faced with routing and it seems I have hit a dead end. I have the following scenario: client1: 192.168.1.10 255.255.255.0 gateway: 192.168.1.100 DNS server: 192.168.1.100 client2: 192.168.1.20 255.255.255.0 gateway: 192.168.1.100 DNS server: 192.168.1.100 server (Windows Server 2008 R2 with enabled RAS & Routing Services) network card 1 (connected to a switch along with the clients) 192.168.1.100 255.255.255.0 DNS server: 127.0.0.1 network card 2 (connected to the router) 192.168.2.100 255.255.255.0 gateway: 192.168.2.1 DNS server: 127.0.0.1 (DNS forwarding to 192.168.2.1) ISP router (with connection to internet) 192.168.2.1 Now in this scenario I have tried to route traffic from the 192.168.1.0/24 network with the clients to the 192.168.2.0/24 network with the routers to connect them to the internet. However, no matter what I do I get no positive ping to the router 192.168.2.1. Ping from 192.168.168.1.10 to 192.168.1.20: Success to 192.168.1.100: Success to 192.168.2.100: Success to 192.168.2.1: not reachable The routing table contains the 2 routes 192.168.1.0 and 192.168.2.0 as directly connected. Does anyone know where the routing fails? I have searched different forums but mostly found nothing relevant. One post however pointed out that in a similar situation the problem was that the router doesn't know the way back and the internet router would need a static route back to the first router. If that really is the case, I take it there is no solution with my equipment, because the standart ISP router doesn't allow to set any static routes.

    Read the article

  • User permissions linux. (proftpd / nginx)

    - by user55745
    I've been having a complete nightmare trying to configure proftpd. I've got proftp server working with an sql database. However I want to have any files uploaded able to viewed by the webserver running on the same box. The folders get created in /var/tmp/ as rwx------ 2 ftpuser ftpgroup 4096 Oct 8 20:35 50730c4346512 drwx------ 2 ftpuser ftpgroup 4096 Oct 8 20:38 50730f3a811ca I've tried adding www-data to group with the following usermod -g www-data ftpuser But this doesn't allow the web server access. In proftpd.conf I have the following umask set Umask 0022 It doesn't seem to make a difference what I set that value to. /etc/group (sure I've messed up one of these two but I'm getting desperate) ftpgroup:x:2001:www-data www-data:x:33:ftpgroup /etc/passwd www-data:x:33:33:www-data:/var/www:/bin/sh proftpd:x:108:65534::/var/run/proftpd:/bin/false ftp:x:109:65534::/srv/ftp:/bin/false ftpuser:x:2001:33:proftpd user www-data:/bin/null:/bin/false The ftpuser table in the database has uid / gid set to 2oo1 for both. I'm going absolutely crazy trying to solve this any help would be greatly appreciated. p.s Also, although if I manually connect to the ftp server I can upload files via FileZilla. Although this isn't working for the web-camera, although there is talky talky going on between the server and the camera.

    Read the article

  • NTFS 'Owner' missing when accessing hard disk from external USB adapter

    - by trismarck
    I have a hard drive with Windows XP SP3 installed on it. When the drive is connected through the standard SATA connector inside the laptop, everything works as expected. However when I remove the drive from the laptop and connect the drive to the external USB adapter, almost all files / folders lose the 'Owner' field contents. I was wondering why could that be. I've tried two USB adapters and this happens on each. I could take the ownership of all of the files, but this would overwrite the Owner value (the Owner value that is present when the drive is accessed through standard SATA connector in the laptop). //edit: if the hard drive is used through the USB adapter, I can't access most of the files, at least until I take ownership of the files (/folders). This is how it looks like: HDD inside USB adapter: HDD inside laptop: (note the Owner column) //edit: some of the files on the first screenshot have Owner field filled up. That's because I took the ownership of those files / folders to be able to access the files on the hard drive. //edit2: also, if the hard drive is connected through USB adapter and if I've took the ownership of some files by the 'ddd' user, then if i login as a different user (lets say 'eee' user), the owner field is _still_ empty: ddd user: eee user: eee user can't access the 'ddd' folder. Both users have Administrator priviledges.

    Read the article

  • How can I pair two bluetooth dongles together?

    - by techaddict
    I want to hack a device which connects via USB, and plug a bluetooth USB dongle to the end of the USB cable (using a female to female adapter), and then connect to that device from another USB bluetooth dongle connected to my computer. How can I do this? It is straightforward? I don't want to spend $30 before I know how to do this. Also I think another concern is that the USB cable is providing power to the device. So I think that means I would also have to hack it for power. I have created this diagram in Photoshop to illustrate my intent: (NOTE: it won't be a USB mouse, as that would be pointless because there are already wireless mice in existence. The mouse is displayed for illustrative purposes) Don't tell me "it won't work". Because I KNOW it WILL work. Think for example, PS3 controller. That works, and in fact I was able to get it working with my laptop, over bluetooth. I just want to know HOW to make it work.

    Read the article

  • Configure linux machine as bridge/switch and end device

    - by leemes
    At my home, I have two desktop PCs in two rooms. The router / DSL modem is in one of these rooms. Now I want to configure a home server (having 2 LAN ports, running 24/7) in the corridor between the two rooms, using only one LAN cable at each door. This gives me the following physical configuration: (door) (door) .----/-/----. .-----/-/----------._ FritzBox | | | .----´´ DSL Router PC1 Server | PC2 As just said, the server has 2 network interfaces and is running Ubuntu. What I need now is a network configuration which enables both the server and PC1 to connect to the router. I think the server needs to serve as a bridge or switch. Currently, all computers are configured having static IP addresses. If I'm understanding it correctly, a bridge / switch doesn't have its own IP address, but as the server needs to be configured as an own end device, it needs to have one. My first question is, do I have to configure both interfaces separately, giving both the same static IP address? My next question is, how do I bridge the two physical networks into one? I have basic understanding (but am always confused again and again) of bridges and switches, but I don't know how to configure it in software. I only know that it's possible to do so :) The third question is: Is it possible to configure this in a way that network packets from/to PC1 to/from the router only go through hardware or only consume low CPU in the server? Can you help me? Thanks in advance!

    Read the article

  • OpenBSD pf - implementing the equivalent of an iptables DNAT

    - by chutz
    The IP address of an internal service is going to change. We have an OpenBSD access point (ssh + autpf rules) where clients connect and open a connection to the internal IP. To give us more time to reconfigure all clients to use the new IP address, I thought we can implement the equivalent of a DNAT on the authpf box. Basically, I want to write a rule similar to this iptables rule which lets me ping both $OLD_IP and $NEW_IP. iptables -t nat -A OUTPUT -d $OLD_IP -j DNAT --to-dest $NEW_IP Our version of OpenBSD is 4.7, but we can upgrade if necessary. If this DNAT is not possible we can probably do a NAT on a firewall along the way. The closest I was able to accomplish on a test box is: pass out on em1 inet proto icmp from any to 10.68.31.99 nat-to 10.68.31.247 Unfortunately, pfctl -s state tells me that nat-to translates the source IP, while I need to translate the destination. $ sudo pfctl -s state all icmp 10.68.31.247:7263 (10.68.30.199:13437) -> 10.68.31.99:8 0:0 I also found lots of mentions about rules that start with rdr and include the -> symbol to express the translation, but it looks like this syntax has been obsoleted in 4.7 and I cannot get anything similar to work. Attempts to implement a rdr fail with a complaint that /etc/pf.conf:20: rdr-to can only be used inbound

    Read the article

  • SSH Connection Error : No route to host

    - by dewbot
    There are three machines in this scenario: Desktop A : [email protected] Laptop A : [email protected] Machine B : [email protected] All the machines have Ubuntu 11.04 (Desktop A is a 64bit one) and have both openssh-server and openssh-client. Now when I try to connect Desktop A to Laptop A or vice-versa by ssh [email protected] I get an error as port 22: No route to host in both the cases. I own both the machines, now if I try same commands from my friend's machine, i.e. via Desktop B, I can access both my Laptop and Desktop. But if I try to access Desktop B from my Laptop or by Desktop I get port 22: Connection timed out I even tried changing ssh port no. in ssh_config file but no success. Note: that 'Laptop A' uses WiFi connection while 'Machine A' uses Ethernet Connection and 'Machine B' is on an entirely different network. Laptop A && Desktop A - Router/Nano_Rcvr provided to me by ISP. So to one Router two Machines are connected and can be accessed at the same time. here is my ifconfig output for both the machines :- Laptop wlan0 Link encap:Ethernet HWaddr X:X:X:X:00:bc inet addr:1.23.73.111 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::219:e3ff:fe04:bc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:108409 errors:0 dropped:0 overruns:0 frame:0 TX packets:82523 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:44974080 (44.9 MB) TX bytes:22973031 (22.9 MB) Desktop eth0 Link encap:Ethernet HWaddr X:X:X:X:c5:78 inet addr:1.23.68.209 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::227:eff:fe04:c578/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10380 errors:0 dropped:0 overruns:0 frame:0 TX packets:4509 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1790366 (1.7 MB) TX bytes:852877 (852.8 KB) Interrupt:43 Base address:0x2000

    Read the article

  • G4 server running slow

    - by Abby Kach
    I have HP proliant ML 350 servers. We have 8 remote locations where users connect and log on to our server through DYNDNS to access our company ERP's to conduct day to day work. The base of our company ERP's is oracle for which we have a separate server.Now the problem is day by day the load on the server is increasing and the speed is getting slower and slower and users are facing a lot of issues . so I are planning to implement Sonic wall VPN. I conducted a demo of sonic wall but it was slower than the current speed of dyndns. the configuration of my server is as follows :- Linux HP ProLiant 370 Intel Xenon 3.20 GHZ 150 GB (72 * 2) 3 GB Suse Omega HP ProLiant 370 Intel Xenon 3.20 GHZ 300GB (72.8 * 4) Raid 5 4 GB Windows Server 2K3 Enterprise Edition Storage Box HP Storage Works 1400 Intel Xenon 2.00 GHZ 4 TB(1 TB * 4) Raid 5 2 GB Windows Server 2K8 Enterprise Edition Domain & Terminal HP ProLiant 350 Intel Xenon 3.20 GHZ 250 GB(72.8 * 3) Raid 5 4 GB Windows Server 2K3 Enterprise Edition Can some one help me as to how can i speed up my network at remote locations and reduce the problems of speed etc..

    Read the article

  • ssh initial prompt hangs for 10 minutes but console login and initial prompt is very responsive - why?

    - by rfreytag
    I have been running an ESXi 4.0 server for months with a couple of WinServer2003 and several Ubuntu Server 10.4 VMs. The performance has been impressive on 6GB i7 Asus P6T hardware. Suddenly, a week ago, ssh logins to the Ubuntu VMs take 10 minutes when connecting over the LAN (over a WAN the connection (pipe) is broken long before that). When logging in to these VMs the password prompt arrives immediately, and failed passwords are responded to immediately. But the moment I log in then the shell prompt appears and I hang for many minutes. Sometimes the connection hangs before the shell prompt appears and sometimes I can type in a command but the moment I hit return the machine hangs. 10 full minute later control returns and the VM is responsive. NOTE: there are several Ubuntu VMs on the same host machine that are identical in all ways that I can tell. However, only one of the VMs displays this behavior. That is why I mention the ESXi host in passing - I don't think it has anything to do with the problem. This behavior is never seen when I connect with the troubled-VM's console (through vSphere Client). From the console the Ubuntu VMs all respond beautifully. I have seen: http://kb.vmware.com/selfservice/microsites/search.do?cmd=displayKC&docType=kc&externalId=1003496&sliceId=1&docTypeID=DT_KB_1_1&dialogID=229586372&stateId=1%200%20229588522 ...and since that relates to delays in seeing the password prompt that does not appear to be the solution here. Any other suggestions very welcome - thank you.

    Read the article

  • Linux will not activate wireless after device has been re-enabled

    - by XHR
    Using a Eee 900A netbook by Asus. By pressing Fn + F2, I can disable or enable the wireless chip on the netbook, a blue LED indicates the status. I've been able to connect to wireless networks just fine with this netbook. However, if the wireless chip ever becomes disabled, I have to reboot to get my network connection back. This generally happens when suspending. For some reason the LED will be off and I have to hit Fn + F2 for it to light up again. However, after doing so, Linux will not reconnect to the network. It simply changes the wireless status from "wireless is disabled" to "device not ready". Even worse, I've recently had issues with the chip being enabled at boot, thus making it nearly impossible to get connected. I've searched around on-line but haven't found much of anything useful on this. This happens on all kinds of different distros including Ubuntu 9.10 Netbook, EeeBuntu 4 beta, Jolicloud and Ubuntu 10.04 Netbook. Edit I noticed this question is getting a lot of views. To give a quick update, I never did resolve this issue with the given distro's. However, I'm currently running Ubuntu 10.10 netbook edition and this issue has gone away.

    Read the article

< Previous Page | 497 498 499 500 501 502 503 504 505 506 507 508  | Next Page >