Search Results

Search found 14951 results on 599 pages for 'connect by'.

Page 497/599 | < Previous Page | 493 494 495 496 497 498 499 500 501 502 503 504  | Next Page >

• Multiple Video Cards - Stuttering

  - by jstawski

  I have two video cards: - XFX PVT84JUDD3 GeForce 8600GT XXX 256MB 128-bit GDDR3 PCI Express x16 SLI Supported Video Card - EVGA 256-P1-N399-LX GeForce 6200 256MB 64-bit GDDR2 PCI Video Card both running the same set of drivers on Windows 7 64-bit. When I work with 2 monitors connected to the 8600GT card everything works smoothly. When I connect the third one to the 6200 then Windows works well and all of a suddon the screens turns black for up to 5 minutes. Then it goes back and at some random interval it goes black again. I can still see the pointer and hit CTRL+ALT+DEL and see the menu to log off, bring the task manager, etc. I've tried changing the 6200 to another PCI slot and the error persists. I've tried connecting 2 monitors only one to each card, same problem. Tried swapping them, mixed and matched the monitors to see if it was a problem with the monitor and my conclusion was that it is not the monitor. The problem also occurred with Vista 64 as well. What could be generating this problem? Can it be the fact that they are different interfaces? Maybe the Motherboard? Should I change something on the BIOS? What do you guys think?

  Read the article

• Create image (EBS AMI) takes forever - possibly caused MySQL Server to break?

  - by fuzzybee

  I'm trying to create an EBS AMI from my running EC2 instance to reuse my LAMP fully configured (for my needs). I got my website up and running yesterday on this EC2 instance my MySQL was working fine until this morning (it's not that difficult to install LAMP thanks to yum so I can't see how I could go wrong with this; having said that, it's always difficult for one to realise his own errors) I have seen "Loading, please wait ..." for a few hours now. How do I know whether this is completed or its progress? Shortly after I tried to create the AMI image from my EC2 instance, I encountered database connection error can't connect to local mysql server through socket '/var/lib/mysql/mysql.sock' I was able to restart mysqld at first. But database connection was down again. This time, I could not restart mysqld anymore. It shows MySQL Daemon failed to start. Could my attempt to create the AMI by any chance cause the MySQL server to reboot or corrupt? I did a lot of searched and have done the following although I think I shouldn't have to do any workaround for MySQL server to work here chown -R mysql.mysql /var/lib/mysql/ I also found this workaround but I'm very reluctant to follow due to my belief and the fact I would need to understand this problem first. Any help would be greatly appreciated. Getting back to searching for a solution for the MySQL server problem ... Thanks, Eric

  Read the article

• using gmail as email relay for sendmail

  - by Nikita

  I used to be able to send emails using a gmail account & sendmail configured using one of the guides on the Internet, for example: http://appgirl.net/blog/configuring-sendmail-to-relay-through-gmail-smtp/ This is a small server and I've recently moved it to a different house. And sendmail has stop working. The only thing different in the network setup is a new router. What is happening: In the log files, I see the following error: ...stat=Deferred: smtp.gmail.com: No route to host When I run from the command line: strace sendmail -f A -t B -u "Subject" -m "Message" -tls=yes ssl=yes -s smtp.gmail.com:587 -xu A -xp XYZ It hangs on this call: recvfrom(3, "m0\201\203\0\1\0\0\0\0\0\0\4ares\3lan\0\0\34\0\1", 8192, 0, {sa_family=AF_INET, sin_port=htons(53), sin_addr=inet_addr("192.168.1.254")}, [16]) = 26 close(3) = 0 time(NULL) = 1339997943 open("/etc/localtime", O_RDONLY) = 3 fstat64(3, {st_mode=S_IFREG|0644, st_size=3477, ...}) = 0 fstat64(3, {st_mode=S_IFREG|0644, st_size=3477, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb76ff000 read(3, "TZif2\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\4\0\0\0\4\0\0\0\0"..., 4096) = 3477 _llseek(3, -24, [3453], SEEK_CUR) = 0 read(3, "\nEST5EDT,M3.2.0,M11.1.0\n", 4096) = 24 close(3) = 0 munmap(0xb76ff000, 4096) = 0 socket(PF_FILE, SOCK_DGRAM|SOCK_CLOEXEC, 0) = 3 connect(3, {sa_family=AF_FILE, path="/dev/log"}, 110) = 0 send(3, "<18>Jun 18 01:39:03 sendmail[268"..., 96, MSG_NOSIGNAL) = 96 nanosleep({60, 0}, So it looks like at some point it tries to resolve the DNS name, but I don't have anything running on 53, so it dies out and then just hangs. The other interesting thing is that msmtp works just fine on the same server. Update: ares in strace output is actually the name of my server, but .254 IP address is the address of the router. Could anyone tell me why this is happening or what further steps can I take to investigate the issue? Thanks!

  Read the article

• How to configure Windows user accounts for ODBC network with NT authentication?

  - by Ian Mackinnon

  I'm trying to create a connection to an SQL Server database from the ODBC Data Source Administrator using "Windows NT authentication using the network login ID". Both server and client are running Windows XP. It appears that any account with administrator privileges can add the data source on the server*, though connection attempts from the client result in error messages that suggest it is trying to authenticate using a guest account. I found a Microsoft support page that says: For SQL Server...: connect using the impersonated user account. But it doesn't offer advice about how to do that. How do I impersonate a user account on the server? or (since it sounds like that would lead to an unfortuante squashing of privileges and loss of accountability): How do I give an account on the client privileges on the server database and then ensure the client attempts authentication with the privileged account and not with a guest account? I'm aware that I'm providing rather sparse information. This is because I'm in unfamiliar territory and don't know what's pertinent. I'll attempt to add any requested information as quickly as possible. *I'm planning on tightening privileges straight after I get it working as it stands.

  Read the article

• Regarding AD Domain controllers and remote branch offices

  - by Alex

  We have central HQ building and a lot of small branch offices connecting via VPN and want to implement AD (If you can believe we still haven't). We want everyone to log in using domain accounts and be policed centrally. We are OK with having a RODC in a branch office with like 10 computers. But we have these small branches with two to four PCs only. Some of these branches connect to HQ via IPSec site-to-site VPN, some via remote access (client-based) VPN. So there is no problem with ones that have local RODC or connecting to HQ DCs via VPN router. But how about small branches? We don't really want to set up a machine there, neither we want to invest into Windows Server licenses or fancy network equipment. Also, the problem is that we cannot access HQ DCs via VPN because we are not logged in and connected to HQ internal network yet, so DCs aren't reachable. What is typically done in that situation if it is needed to have central management over policies on those PCs? Or is it better to let 'em loose and use local policies and accounts in this situation?

  Read the article

• Trouble printing to local printer when connected to VPN with split-tunneling enabled

  - by Marve

  I'm a volunteer network admin for a multi-tenant non-profit office space. One of our new tenants uses a VPN to connect to remote resources using RRAS and Small Business Server 2008. They also have a local network printer for the workstations in our office. When connected to the VPN, they cannot print to the local printer. I informed their network admin that they need to enable split-tunneling to fix this. Their network admin enabled split-tunneling, but apparently printing still didn't work. He told me that I need to open port 1723 on our office firewall to allow it to work. I'm just a novice administrator and not familiar with RRAS, but this doesn't sound right to me and I haven't been able to find anything on the web to validate it. Additionally, my understanding of split-tunneling is that it is handled entirely by the VPN client and should work irrespective of firewall settings. Is my understanding of the situation incorrect? What steps should I take to resolve this problem?

  Read the article

• Checkpoint VPN-1 R60 and Windows 7 64 Bit Client

  - by Mohit

  Hi All, As per my knowledge of checkpoint VPN-1. My company is using checkpoint VPN-1 R 60 ( I guess as I dont know how to check server version) Firewall(VPN Server). Now the problem is that I installed Windows 7 64 bit. But, after my research I found that there are not even one client (SecuRemote/SecuClient) for Win7 64 bit, when Firewall or server is R60. I thought of some open source solutions. Can you guys please suggest me some with the configuration required. As of now, I know the IP of the server. I know my username and password using which I connect and that is not my domain password. that i can confirm to you guys. I am not a network guy. I am more of a developer. But, I need some help in this.So, let me know if I can provide you more details. Please please i need urgent help on this.

  Read the article

• Outlook locking network connection/session?

  - by HaydnWVN

  Scenario: We have an 'automatic orders' machine sat in the corner running XP with Outlook 2003. Its job is to check for new emails on a specific account, when it encounters one it checks the e-mail body for specific wording to determine which customer it is from (using a macro), then it checks the attachment for specific order codes before parsing the attachment to create a .csv file (which is then e-mailed onto one of the sales team) before importing the .csv into our bespoke ERP/Sales Order system to create an order. Problem: Periodically the machine will have symptoms of a lost network connection (unable to connect to any network source). Sometimes after several days, sometimes over a week. Volume of emails/orders processed does not seem to be linked. Additional info: The machines .pst is stored on a mapped network location. The .csv created is stored on a mapped network location. This is a workgroup, not a domain. All network drives are Samba shares from an Ubuntu fileserver. Our bespoke system runs from a database (MySQL) Ubuntu server. Our troubleshooting so far: I have switched machines (previous was Win2000) with the same symptoms. Restarting the machine FIXES the problem. Closing Outlook and then end tasking an Outlook.exe background process FIXES the problem. If you close Outlook, without end taking the background process, outlook will not reopen (saying it cannot find the pst file & it will not open any network location). Does Outlook have some kind of 'max session' linking it to network activity that is not closing after a mail request? Could Auto-archive be causing this? Is there a tool to check/display what each outlook.exe process is doing? Have not found many ways to troubleshoot this yet, as it is so infrequent...

  Read the article

• AWS: Multi-region setup using single RDS instance

  - by Ion

  I'm trying to scale our web application (PHP, MySQL, memcache) in a multi-region scheme. Currently we are using a setup with two EC2 instances behind an ELB and an RDS instance, all of them in US-EAST (Virginia) region. We would like to have a presence in the EU (Ireland) region as well. This means at least a new EC2 instance there (identical to the others, serving the same application). I have copied the desired AMI, setup the new instance, setup a same ELB configuration (required for SSL termination) and configured latency-based routing in Route53. And it works as suggested. But, clients from EU have speed problems. This is due to the fact that the EU EC2 instances connect to the US-based RDS instance. As far as I know Amazon has not yet enabled RDS multi-region replication. Do you have any suggestions on how to properly speed up the whole setup while using the single RDS instance? Also, any ideas in general on how to scale things up? Ideally we would like to continue using the RDS technology for various reasons. Nevertheless, I am open to suggestions (I guess the next idea would be to host our own MySQL servers).

  Read the article

• VNC Address Book - Window Invisible? Working as intended?

  - by user1445967

  I have VNC Server and VNC Viewer on the same PC with Windows 7 Ultimate x64. Is VNC Address Book supposed to have a main application window? I can't tell if this is bugged or working as intended. When I start VNC Address book, it creates an item in the task list and also an icon in the notification area. If I click the task list item once, nothing happens. If I click again, it disappears from the task list but remains in the notification area**. If I right-click the icon on the notification area, there is an option 'open address book', which if chosen, creates the item in the task list again, with the exact same behavior. If I left or right click on the address book icon, I have ways to connect to servers in the address book. However I have no way to add/remove/edit servers in the address book. **Note that this behavior is identical to that of an application with a main window where there is an option to 'minimize to system tray / notification area'. Only here, no main window is visible, ever. If fixing this problem is beyond the scope of this site, that's fine, but at this point I have no real way to tell if the program is malfunctioning on my pc or if it is far more minimalist than I expected. There appears to be no forum on realvnc.com where I can ask about this, perhaps this is to prevent me from getting any help unless I pay to register?

  Read the article

• RTNETLINK answers: File exists... maybe because assigned a new mac adress

  - by steven

  I got a "RTNETLINK answers: File exists Failed to bring up eth0:1" on "ifup eth0:1". I suspect it happens because i assigned a new mac adress in my VM's network adapter. Can you tell me how to fix the issue? My configuration looks like this: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 allow-hotplug eth0 iface eth0 inet static address 192.168.1.80 netmask 255.255.255.0 gateway 192.168.1.1 dns-nameservers 192.168.1.1 # Alias being connected to 192.168.10.x Network auto eth0:1 allow-hotplug eth0:1 iface eth0:1 inet static address 192.168.10.83 netmask 255.255.255.0 gateway 192.168.10.10 dns-nameservers 192.168.10.1 Why do I get "RTNETLINK answer: File exists.." suddenly? I worked with this configuration before without problems. All i did in the past is to renew the adapters mac adress. At the moment I am connected to the 192.168.10.x Network and if I do /etc/init.d/networking stop /etc/init.d/networking start then i got "RTNETLINK [...] falied to bring up eth0:1" but the strage thing is that i am able to connect to 192.168.10.83 via ssh from my host machine. But I cannot reach the internet from the debian client. I hope it is clear what my problem is, now. update if i change my /etc/network/interfaces like this then "ifup eth0" fails, too with the same error! # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 allow-hotplug eth0 iface eth0 inet static address 192.168.10.83 netmask 255.255.255.0 gateway 192.168.10.10 dns-nameservers 192.168.10.1 with verbose option enabled i got: Configuring interfache eth0=eth0 (inet) run-parts --verbose /etc/network/if-pre-up.d ip addr add 192.168.10.83/255.255.255.0 broadcast 192.168.10.255 dev eth0 label eth0 RTNETLINK answers: File exists Failed to bring up eth0. same if i type this manually: ip addr add 192.168.10.83/255.255.255.0 broadcast 192.168.10.255 dev eth0 label eth0

  Read the article

• VPN - local and remote networks IP collision

  - by Guido García

  I have created a VPN connection in Windows using the New Network Connection wizard that comes with Windows. It works without problems in most places, but there is one concrete place where, despite the connection to the remote public IP works fine, it is not able to validate the login/password and establish the VPN connection. In this place, the network is 10.0.0.x (the same I use in other places where I am able to connect). The remote network is 192.168.x.x, so I suspect there is some kind of IP collision, because before connecting, a traceroute to i.e. 192.168.0.40 does not fail. 1 4 ms 1 ms 1 ms LINKSYS [10.0.0.1] 2 5 ms 1 ms 1 ms 172.26.27.1 3 4 ms 5 ms 3 ms 192.168.1.100 ... (more) I can't modify the local network further than the first router (10.0.0.1). That is the only different I've found so far. Any idea about how to solve it? Thank you.

  Read the article

• Best NIC config when virtual servers need iSCSI storage?

  - by icky2000

  I have a Windows 2008 server running Hyper-V. There are 6 NICs on the server configured like this: NIC01 & NIC02: teamed administrative interface (RDP, mgmt, etc) NIC03: connected to iSCSI VLAN #1 NIC04: connected to iSCSI VLAN #2 NIC05: dedicated to one virtual switch for VMs NIC06: dedicated to another virtual switch for VMs The iSCSI NICs are used obviously for storage to host the VMs. I put half the VMs on the host on the switch assigned to NIC05 and the other half on the switch assigned to NIC06. We have multiple production networks that the VMs could appear on so the switch ports that NIC05 & NIC06 are connected to are trunked and we then tag the NIC on the VM for the appropriate VLAN. No clustering on this host. Now I wish to assign some iSCSI storage direct to a VM. As I see it I have 2 options: Add the iSCSI VLANs to the trunked ports (NIC05 and NIC06), add two NICs to the VM that needs iSCSI storage, and tag them for the iSCSI VLANs Create two additional virtual switches on the host. Assign one to NIC03 and one to NIC04. Add two NICs to the VM that needs iSCSI storage and let them share that path to the SAN with the host. I'm wondering about how much overhead the VLAN tagging in Hyper-V has and haven't seen any discussion about that. I'm also a bit concerned that something funky on the iSCSI-connected VM could saturate the iSCSI NICs or cause some other problem that could threaten storage access for the entire host which would be bad. Any thoughts or suggestions? How do you configure your hosts when VMs connect direct to iSCSI?

  Read the article

• ATI firepro will not detect a second DVI-D monitor

  - by John

  OK so weird issue here. I have previously been running 6 screens off of 3 of the older ATI firepro graphics cards but they had a problem with the heat sink getting too hot and warping the PCB resulting in total failure of the card, to replace my three dead cards I purchased a new-type ATI firepro with the newer heat sink design. I'm only using one at the moment to make sure they've fixed the problem before I waste more money on 2 more cards but this is where things start to get weird. The Firepro's only have one port on them, they connect to two monitors via a splitter cable going from the one port to two DVI connectors for the screens. When I plug two identical monitors in via their DVI inputs not matter what I do windows and Catalyst will only detect one screen. However if I use the VGA input on one of the screens with a VGA - DVI adaptor to plug it in to the card it works fine. This confuses me greatly. I'm currently using the ATI Firepro 2270 Graphics card with identical DELL U2311H screens. I can post the rest of the system spec as well if needed but I wouldn't have thought it would make much difference as it had no problem handling 6 screens before the graphics cards failed. Naturally both catalyst and ATI drivers are the most current version. ATI tech support has been absolutely zero help, they seemed to get stumped as soon as I verified that both screens were plugged in and connected properly. Anyone have any ideas?

  Read the article

• HP dv6910 laptop no longer recognizes wireless adapter, dvd drive, and one usb port. What can I do about this?

  - by Joan H.

  In the last 3 weeks, my not even 3 year old HP laptop (vista) just seems to be failing. First, one of the usb ports stopped working. Next, the dvd drive all of a sudden was not recognized as even existing, so it is now useless. And as of today, I no longer seem to have a wireless adapter on my laptop. It doesn't show up in device manager, same as the dvd drive. I can connect to the internet by ethernet cable, but not wirelessly. It worked fine last night; now it doesn't even exist! I have tried a 'hard reset' I read about on HP's forum- no help. I am not sure what else to try. I read about the USB wifi dongle in another response, but I already have maxed our my usb ports even though I have bought a USB hub since the one port failed. Plus, I'd like my laptop to just work like it's supposed to instead of being jerry rigged with usb hubs, external dvd drives, and wifi dongles etc. Any ideas?

  Read the article

• Does a VPN requirement kill the concept of having a Web Application in the Cloud?

  - by Christian

  Recently I posted a question in SO, but so far I got no answers. I wonder if I'm asking the wrong question. This is the problem: We need to design an application which offers a public http web service, but at the same time it must consume some services through a VPN connection from other existing company. There is no other alternative but to use a VPN connection to access those services. We want to host our application in some cloud infrastructure like Heroku or Amazon EC2. But there is no direct way to access the VPN services of the other company from there. The solution I'm thinking, but I don't like is to have a different server to expose the services from that VPN. But this will require the setup of another server which I prefer to avoid. In the case this is the solution, can I use an Amazon EC2 instance to connect to a VPN? This is what I was thinking, is it correct? I don't have experience using VPNs, tunnels or those kind of networking stuff. I will really appreciate if you can propose me an alternative solution, or just give me a comment.

  Read the article

• No LAN and SMB access, and Explorer not responsive, when using a second connection

  - by Lorenzo

  I apologize if this is a duplicate question, I know that there are several questions about multiple connection (LAN + LAN and LAN + dialup) but I haven't been able to find one that fits my scenario. I'm still using Windows XP on my corporate laptop, and I'm connected to the corporate LAN via Ethernet. The LAN NIC has a public IP address, although not accessible externally, obtained via the corporate DNS server. This connection is firewalled and requires a proxy to access Internet. To access Internet sites blocked by the corporate firewall, I use my smartphone via USB tethering. It is seen as a new LAN interface, and I get a private IP address (class 192.168..). There are two problems: The LAN is not accessible, as the default gateway goes to the tethering NIC. I'd like to solve this, but I can live with it. My PC becomes unresponsive if I use Windows Explorer to view local files, or even when I open the start menu. I guess that this is caused by attemps to connect to a mapped network drive. But I disabled the "Client for Microsoft Networks" in the tethering NIC. Why the system still hangs? Of course if I disable the Ethernet NIC, Explorer stops hanging. If you need further details, add a comment. Thanks!

  Read the article

• Printer spooler service stop running when sent print job

  - by Hanan N.

  Every time i am sending a print job to the printer, i am don't get any response from the printer, and at the printer job list at the status of the job, i see that there was an Error, but it don't give me any clue on what could be the problem. After some investigation i found that every time that i send the print job to the printer the printer spooler service stops to run, then after a second or two it start again (i think that this behavior is related to the printer spooler settings to rerun it self after it stops). Things that i have tried so far: Remove and Install again the Driver. After removing the driver, i have removed the unnecessary registry keys according to this article from Microsoft, these are: Rename all files and folders in: c:\windows\system32\spool\drivers\w32x86 Remove anything but Drivers Print and Processors: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Environment\Windows NT x86 Remove anything in here: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Monitors but: BJ Language Monitor Local Port Microsoft Document Imaging Writer Monitor Microsoft Shared Fax Monitor Standard TCP/IP Port USB Monitor WSD Port Disconnect and Reconnect the Printer. Clean the computer from Viruses & Spywares. Currently i am stuck, i have no more things to try, if anybody know about any kind of solution please let me know about it. Since i am want to keep this post as general problem that relate to the printer spooler, and not just my particular problem, i didn't included inside the windows version & the printer model, they are (although i think that it isn't relate just for that particular model): Windows 7 32bit, HP Officejet 4500 G510g-m (connect to the computer via USB). Thanks.

  Read the article

• How can I make sound over hdmi in kubuntu work?

  - by user32509

  I have used a hdmi cable to connect my lcd (which is connected with my speakers) with my nvida 275 gtx grafic card. I can not get the sound output to work. The hardware itself is working probably - I tested it under windows. Currently I am running Kubuntu 9.10 64 with Nvidia 190.53. The sound output worked fine before I installed the hdmi connection. (German output - i can change it, if you tell me how :)) aplay -l **** Liste von PLAYBACK Geräten **** Karte 0: Intel [HDA Intel], Gerät 0: ALC889A Analog [ALC889A Analog] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 Karte 0: Intel [HDA Intel], Gerät 1: ALC889A Digital [ALC889A Digital] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 aplay -L front:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog Front speakers surround40:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers iec958:CARD=Intel,DEV=0 HDA Intel, ALC889A Digital IEC958 (S/PDIF) Digital Audio Output null Discard all samples (playback) or generate zero samples (capture) pulse Playback/recording through the PulseAudio sound server And i disabled mute in kmix an all channels :)

  Read the article

• Instructions to setup primary and only domain controller

  - by Robert Koritnik

  Where could I get best step by step instructions (with some simple explanations) how to setup domain controller on Windows Server 2008 R2 Server Core? I don't know what do I need? Do I need DNS as well and AD and so on and so forth. I don't know enough about these things, but I need to set them up to prepare development environment. I would also like to know how to configure firewall on DC machine, to make it visible on other machines because I've setup DC somehow but I can't connect to it... This is my HW config: Linksys internet router with DHCP my dev machine is Windows 7 my DC machine is a VM in my dev machine my dev machine has a hw network adapter to linksys and a virtual network adapter to DC DC machine has two network adapters: one to linksys (to be internet connected so it can be updated etc.) and one to host (my dev Win7 machine) Edit My development machine should access domain controller and logon using domain credentials. Development machine would access internet directly via Linksys router. My domain controller machine would only serve authentication (and if I'm able to configure it right) should also have Active Directory Federation Services in a workable condition. I hope this is a bit more clear now. At least a small bit.

  Read the article

• How to avoid sshfs freezing?

  - by Andreas Hagen

  So the issue is this: I've installed sshfs on Ubuntu 12.04 and I'm trying to connect to a couple of remote servers. So initially the mount seams successful. Sometimes Gnome even picks it up and displays the "new device found" box at the bottom of the screen. but from here on there is not much that works. Or at least not any more. The first couple of times i connected it seamed to work fine, and I was able to transfer some files, then i disconnected using fusermount -u <folder> and after reconnecting a little later the trouble started. Now after executing sshfs -o ServerAliveInterval=15 -o reconnect -C -o workaround=all -o idmap=user root@<host>:/ <folder>, when I change directory into the mount-point, the shell just freezes. Strangely ls -al <folder> works when listing just the root of the remote system, but nothing more. Also every file-explorer I've tried freezes just like cd <folder>. To me it seamed like there was some kind of zombie thread or something hanging around my system, due to the fact that it did work the first time, so I have tried rebooting but no luck. sshfs -V gives this: SSHFS version 2.3 FUSE library version: 2.8.6 fusermount version: 2.8.6 using FUSE kernel interface version 7.12 So yea, any ideas?

  Read the article

• How to set up daisy-chained routers for separate sub-nets?

  - by joe

  This question seems to be similar to others, but I'll take a shot anyway. A client recently switched ISPs from TDS to Comcast Business Class. Before the switch, they had 5 static IP addresses assigned. Now they'll have a single IP address that will change whenever Comcast decides to do so. The issue is that this internet connection will be shared among two companies, both having (and wanting to keep) their own private subnets. Because TDS was supplying multiple IP addresses to the one location, this allowed me to put each router on the switch. Now, with Comcast, they only get one IP address, meaning there has to be a main router before the subnet routers. Luckily, the cable modem has a built-in router, which I would like to connect to each company's router, and still have DHCP enabled on all accounts. Question: What do I need to do to the subnet routers to keep them separate from each other, but still allow internet access from the main router. I would love to say "I tried this", and give you links, but everything I find on the internet only mentions daisy-chaining routers with DCHP disabled.

  Read the article

• Looking to get a small server – need web, PHP, PostgreSQL.

  - by Javawag

  Hi all! I'm looking to get a cheap (low end) server to serve web pages (xHTML/PHP), but I also need to be able to set up PostGreSQL on the system too. Ideally the server would have low power consumption, run Linux (I prefer Mac OS X but a Mac Mini, although the size I'm looking for, is too much money!) and be around £100 (~$160US). EDIT: Just to make it clearer, I'm looking to purchase the server hardware myself – but I want something about Mac Mini sized. I don't want to pay for hosting! Also, quick question – if it's to serve web pages from my home (standard ISP connection, no static IP!), what do I need in place to get this working. I'm guessing I would sign up with some service like no-ip, and register a domain to point to my no-ip address (then install the no-ip software on the server to update that with the current IP). I know the idea of running a server behind a normal ISP connection isn't very elegant, but I'd prefer to have the server where I can see it then pay over the odds for a hosting service where I have little to no control over what happens. Also, I could write my own server software for apps/etc to connect to as well. Anyways I'm rambling! What do you guys think?! Javawag

  Read the article

• Implementing emailing (bulk & event based) features for my website.

  - by Kabeer

  Hello. For my upcoming social networking website, I am looking for suggestions on the best way to implement emailing. Here are some of my requirements and constraints: Requirements: - Should be able to send emails based on events (new registrations, change password, etc.), promotions (advertisements based on user consent), bulk mails (newsletters), reminders (profile updates), etc. I hope I got the point through. - Should be able to process faults (incorrect email address, mail-box full, etc) - User initiated invites (inviting friends to connect) Constraints: - As of now I am looking at Godaddy for hosting. Subsequently I shall move to, may be Amazon Cloud. Godaddy seems to be excruciatingly conservative (not bad always) when it comes to the ability to send email. - My tests on Godaddy so far have been discouraging. There is limit to no. of emails I can send and sometimes if emails carries special characters it throws strange exceptions like there was a virus affected attachment (even though I hadn't attached a thing). The replies from Godaddy support have been equally funny. My intent is not to portray Godaddy as wrong but I am looking for a work-around that frees me from said constraints. I am looking for a mechanism / service that is either free of very cost effective. I wonder how other sites address this. Mine is a .Net / Windows based application.

  Read the article

• Guide To Setting Accessing PhpMyAdmin On NGINX, Ubuntu 11.04, EC2 Remote MySQL Instance

  - by darkAsPitch

  I have setup a domain name to run on amazon ec2 running ubuntu 11.04, nginx and php5-fpm. The domain name works great, I have setup it's own sites-available configuration file and sym-linked it to sites-enabled. I installed phpmyadmin via sudo apt-get install phpmyadmin and followed the instructions. I then added this just above my /etc/nginx/nginx.conf file and restarted nginx. server { listen 80; server_name phpmyadmin.domain.com; location / { root /usr/share/phpmyadmin; index index.php; } #make sure all php files are processed by fast_cgi location ~ \.php { # try_files $uri =404; fastcgi_index index.php; fastcgi_pass 127.0.0.1:9000; include fastcgi_params; fastcgi_split_path_info ^(.+\.php)(/.+)$; fastcgi_param PATH_INFO $fastcgi_path_info; fastcgi_param PATH_TRANSLATED $document_root$fastcgi_path_info; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; } } I have also added the appropriate dns A records for phpmyadmin.domain.com phpmyadmin.domain.com just shows a 404 error code. All other subdomains do not respond at all so at least something is working here. FYI I have edited the /etc/phpmyadmin/config.inc.php file so that I can connect to a remote MySQL Database. What else do I need to do?

  Read the article

< Previous Page | 493 494 495 496 497 498 499 500 501 502 503 504  | Next Page >