Search Results

Search found 29876 results on 1196 pages for 'ubuntu 8 04 lts'.

Page 501/1196 | < Previous Page | 497 498 499 500 501 502 503 504 505 506 507 508  | Next Page >

  • Bridged VM guest does not get IPv6 prefix

    - by Arne
    I have a similar problem and setup as described in IPv6 does not work over bridge. My host get a IPv6 prefix but the guest VM only gets a local fe80-prefix. Using tcpdump I can see that solicit messages are going out from the guest but the host (ubuntu-server) doesn't seem to respond: arne@ubuntu-server:/var/log$ sudo tcpdump -i br0 host fe80::5054:00ff:fe4d:9ae0 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on br0, link-type EN10MB (Ethernet), capture size 65535 bytes 14:31:15.314419 IP6 fe80::5054:ff:fe4d:9ae0 > ff02::16: HBH ICMP6, multicast listener report v2, 4 group record(s), length 88 14:31:15.322337 IP6 fe80::5054:ff:fe4d:9ae0 > ff02::16: HBH ICMP6, multicast listener report v2, 1 group record(s), length 28 14:31:15.502374 IP6 fe80::5054:ff:fe4d:9ae0 > ff02::16: HBH ICMP6, multicast listener report v2, 1 group record(s), length 28 14:31:15.743894 IP6 fe80::5054:ff:fe4d:9ae0.dhcpv6-client > ff02::1:2.dhcpv6-server: dhcp6 solicit 14:31:15.802389 IP6 fe80::5054:ff:fe4d:9ae0 > ff02::16: HBH ICMP6, multicast listener report v2, 4 group record(s), length 88 14:31:17.906580 IP6 fe80::5054:ff:fe4d:9ae0.dhcpv6-client > ff02::1:2.dhcpv6-server: dhcp6 solicit I had a firewall issue which I fixed by adding the following (copied from similar IPv4 before.rules settings) to /etc/ufw/before6.rules at the end before the commit statement: # allow bridging (for KVM) -I FORWARD -m physdev --physdev-is-bridged -j ACCEPT I am running the host on a Ubuntu 14.04 server so I guess I could have used dnsmasq but I didn't find any howto for it so I used radvd (which had to be installed) with the following configuration in /etc/radvd.conf: interface br0 { AdvSendAdvert on; AdvLinkMTU 1480; prefix 2a01:79d:xxx::/64 { AdvOnLink on; AdvAutonomous on; }; }; This didn't help though so I guess I must have configured it wrong? Any help appreciated. Br, Arne PS: I wish the Ubuntu documentation included how to configure virtualization to work with IPv6

    Read the article

  • Remmina 1.0 problems

    - by kamil
    I downloaded, compiled remmina and freerdp from the source repositories. Unlikely I am having troubles in RDP connections. When I initiate any RDP connection from Remmina, Remmina is closed immidialtely. I tried to open freerdp from terminal, it worked like a charm. I tried to open remmina from terminal to check errors. It says: segmentation fault - after connecting to any rdp connection I got the source from git: git clone git://github.com/FreeRDP/Remmina.git git clone git://github.com/FreeRDP/FreeRDP.git// Compilation is successfull with all dependencies. I tried to remove old remmina 0.9.9.1 with no chance I tried to reboot my machine and issue ldconfig with no chance I switched to other rdp clients right now. How can I be able to fix this? the old remmina was working well with RDP but causing sometimes high memory consumption (about 1GB of RAM) I am using Ubuntu 12.04.1 64bit

    Read the article

  • Nvidia G96 [GeForce 9400 GT] and application graphic issues

    - by Fabio
    I've got a quite old NVIDIA graphic card and I with installed restricted drivers from Settings panel (as also shown in this thread). ? ~ lspci 02:00.0 VGA compatible controller: NVIDIA Corporation G96 [GeForce 9400 GT] (rev a1) I tried a lot of them: version 173-update, current, beta, but the only one that can run unity-2d it's current-update. That's Ubuntu 12.04.1 LTS 64bit. However... Unity crashes, sometimes windows border disappear, Java Virtual Machine doesn't works, font rendering it's slow and so on. How can I solve this? Some suggestions? Thanks!

    Read the article

  • I cannot search/find any applications in the Dash on 12.04

    - by Russell
    Its been a while since I booted my Ubuntu (12.04), but when i did I had several updates (over 100) and I installed them along with rebooting. These updates seemed to mess with my video driver but I seemed to have fixed this. My problem is that my applications do not show anywhere. I can open them via terminal or if there are shortcuts (such as on the toolbar) but if I hit Super and go to Apps, there is nothing. This is true if I hit Super and search any app name nothing will come back (except for files). I need help to understand what happened! Also for some reason I can't upgrade to 12.10 (I assume because I have 12.04 and not 12.04.1, which I don't understand how to get).

    Read the article

  • Can't connect to Wired Network after installing 12.04

    - by ezz9
    I have installed 12.04 into a used HP Compaq DC 7100 CMT. Plugged in LAN cable into the computer and it says network disconnected. from what I understand on the things I've read, it's not getting the address right, maybe it's just a guess (hardware address 00:16:35:78:47:bb). I know the LAN cable is working I can get on the net with the old computer. (Old computer is using device MAC address; Auto eth0 00:11:11:E6:4F:FE). I have put this address into the newer HP and it shows last used (minutes ago) but no Internet sever not found. I tried the hardware address it says never. I feel and think this should be easy to fix. But I just don't know. Here is the info everyone has asked for, but they never say what I should do. sudo lshw -C network; rfkill list; cat /etc/network/interfaces; cat /etc/lsb-release; lspci -nn; lsusb; uname -a; ifconfig; route -n *-network description: ethernet interface product; NetXtreme BCM5751 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:40:00.0 logical name: eth0 verson: 01 serial: 00:16:35:78:47:bb size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000-fd configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion= 3.121 duplex=full firmware=5751-v3.29a latency=0 link=yes multicast=yes port=twi sted pair speed=100Mbit/s resources: irq:17 memory:f0400000-f040ffff auto lo iface lo inet loopback DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION= "Ubuntu 12.04 LTS" 00:00.0 host bridge [0600]: Inter Corporation 82915G/P/GV/GL/PL/910GL Memory Con troller Hub [8086:2580] (rev 04) 00.02.0 VGA compatible controller [0300]: Intel Corporation 82915G/GV/910GL inte grated Graphics Controller [8086:2582] (rev 04) 00:1c.0 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 [8086:2660] (rev 03) 00:1c.1 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 2 [8086:2662] (rev 03) 00:1d.0 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #1 [8086:2658] (rev 03) 00:1d.1 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #2 [8086:2659] (rev 03) 00:1d.2 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #3 [8086:265a] (rev 03) 00:1d.3 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #4 [8086:265b] (rev 03) 00:1d.7 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB2 UHCI Controller [8086:265c] (rev 03) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI bridge [8086:244e] (rev d 3) 00:1e.2 Multimedia audio controller [0401]: Intel Corporation 82801FB/FBM/FR/FW/ FRW (ICH6 Family) AC'97 Autio conrtroller [8086:266e] (rev 03) 00:1f.0 ISA bridge [0601]: Intel Corporation 82801FB/RF (ICH6/ICH6R) LPC Interfa ce Bridge [8086:2640] (rev 03) 00:1f.1 IDE interface [0101]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 fami ly) IDE Controller [8086:266f] (rev 03) 00:1f.2 IDE interface [0101]: Intel Corporation 82801FB/FW (ICH6/ICH6W) SATA Con troller [8086:2651] (rev 03) 40:00.0 Ethernet controller [0200]: Broadcom Corporation NetXreme BCM5751 Gigab it Ethernet PCI Express [14e4:1677} (rev 01) Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Linux bob-desktop 3.2.0-23-generic-pae #36-Ubuntu SMP Tpr 10 22:19:09 UTC 20 12 i686 i686 i386 GNU/Linux eth0 Link encap:Ethernet HWaddr 00:16:35:78:47:bb inet6 addr: fe80::216:35ff:47bb/64 Scope:link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2517 errors:0 dropped:0 overruns:0 frame:0 TX packets:164 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:164508 (164.5 KB) TX bytes: 40884 (40.0 KB) Interrupt:17 lo Link encap:Local loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:3290 errors:0 dropped:0 overruns:0 frame:0 TX packets:3290 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen: 0 RX bytes:267212 (267.2 KB) TX bytes: 267212 (267.2 KB) Kernel Ip routing table Destination Gateway Genmask Flags Metric Ref Use Iface ran this sudo dhclient eth0 no reply ran this ip addr 1: lo <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST ,MULTICAST ,UP ,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000 link/enter 00:16:35:78:47:BB brd ff:ff:ff:ff:ff:ff inet 169.254.7.172/16 brd 169.254.255.255 scope link eth0:avahi inet6 fe80::216:35ff:fe78:47bb/64 scope link valid_lft forever preferred_lft forever Help please.

    Read the article

  • How to recover unavailable memory in /dev/shm

    - by Alain Labbe
    Good day to all, I have a question regarding the use of /dev/shm. I use it as a temporary folder for large files to speed up processing and save IO off the HD. My problem is that some of my scripts sometimes require "forceful" interruption for a variety of reasons. I can then manually remove the files left over in /dev/shm but the memory is not returned to available space (as seen by df -h). Is there any way to recover the memory without restarting the system? I'm using LTS12.04 and most of the scripts are PERL running system call on C programs (bioinformatics tools). Thanks.

    Read the article

  • Why can't I run Compiz?

    - by jasoncruz98
    I installed Ubuntu 11.10 on my laptop. The main reason I switched to Ubuntu is because I wanted to use Compiz. The first thing I did was to go to Additional Drivers and install ATI/AMD Proprietary FGRLX Graphics Driver. There was also another one available, ATI/AMD Proprietary FGRLX Graphics Driver (post-release updates), but I didn't install that one, because it basically meant the same thing to me as the one I already installed. Next, I went to the ubuntuguide.org Oneiric Wiki http://ubuntuguide.org/wiki/Ubuntu:Oneiric#Compiz_Fusion So I followed the instructions there and ran this command in terminal: sudo apt-get install compiz compizconfig-settings-manager compiz-fusion-plugins-main compiz-fusion-plugins-extra emerald librsvg2-common But then, the terminal window said that the package "emerald" could not be found. So, I ran this command instead: sudo apt-get install compiz compizconfig-settings-manager compiz-fusion-plugins-main compiz-fusion-plugins-extra After that, I installed Fusion Icon by running this command: sudo apt-get install fusion-icon I restarted my computer, searched for Compiz Config Settings Manager, and clicked on it. Then, I activated Wobbly Windows. I logged off and logged back on again, but there was no wobbly windows effect. So I tried clicking on Fusion Icon, but it never started. Can someone please tell me what I did wrong here? Because I see everyone seems to be able to run Compiz except me. I really need to start Compiz, or else I think I'm going to uninstall Ubuntu.

    Read the article

  • How to install Ubiquity into a Live CD installation image?

    - by Patrick L
    I am trying a create a small Ubuntu installation ISO image. I am using a tool called Ubuntu-Builder. To make the final ISO as small as possible, I have decided to use Ubuntu Mini Remix. It is a small Live CD without GUI. It does not come with any installer software like Ubiquity. I want to embed an installer software into the ISO image so that user can install it into harddisk. In Ubuntu-Builder, I have tried the following: Install LXDE Desktop, then install Ubiquity. But the final ISO boots into command line. Install OpenBox Desktop, then install Ubiquity. But the final ISO boots into command line. Do not install DE, directly install Ubiquity. But the final ISO still boots into command line. After booting up from ISO, I have checked the software in the OS. It seems that Ubiquity has been installed. But it didn't show up when I boot the ISO image. Anyone knows how to install Ubiquity into a Live CD ISO image? Anyone knows any text mode installer which can replace Ubiquity?

    Read the article

  • Can't complete dropbox installation from behind proxy

    - by Mark Jones
    Problem: My PC on campus sits behind a proxy (requiring authentication) and I can't setup Dropbox. I am convinced that this is a proxy issue as I can't setup Ubuntu one either (but I don't use Ubuntu One so that is not a problem). I have looked at the Ubuntu One fix but it seems to be to modify settings explicitly related to Ubuntu One. I can install the nautilus-dropbox package (compiled from source and from .deb package from website and from software centre) but once I click OK from the "Dropbox Installation" dialog box (prompting me to download the proprietary daemon) the installation just freezes with the OK button pressed. When I look at its process in System Monitor its waiting channel is inet_wait_for_connect. I have set the following proxy directives thus far: Added mj22:**@proxy.waikato.ac.nz:80 information to network proxy settings under network in settings. Added http_host and http_port variables under gconf-editor-system-proxy Added 'host', 'authentication_password' 'authentication_user' and ticked 'user authentication' and 'use_http_proxy' under gconf-editor-system-http_proxy Added export http_proxy="http://mj22:**@proxy.waikato.ac.nz:80/" to /etc/bash.bashrc Added Acquire::http::proxy "http://mj22:**@proxy.waikato.ac.nz:80/"; to /etc/apt/apt.conf (which is what I imagine is letting Software Center retrieve packages). (where ** is my password) I have also added the equivalent ftp and https lines for the above entries. I get the internet fine and Software Centre can download packages but thats it. Related issues: The software centre can't fetch reviews (but can download packages). When trying to add an online account in Gnome 3 a dialog pop up appears with "Error getting a Request Token: Cannot connect to proxy (proxy.waikato.ac.nz)" Updates: After some time (10mins ish) Dropbox shows an error dialog box that reads: Trouble connecting to Dropbox servers. Maybe your internet connection is down, or you need to set you http_proxy environment variable. Is there a way I can see what environment variables are currently set?

    Read the article

  • Cannot choose windows installation [closed]

    - by Toby
    Possible Duplicate: Ubuntu 12.4 and XP on Seperate Drives, Dual Boot, How? I've never used Linux before in any form, but was always intrigued, so after a while of deciding whether to risk it I installed Ubuntu 12.04 During the installation I was asked "what would you like to do?" Install Ubuntu as the only operating system, alongside another os, or something else. I chose something else as I wanted to format one of my old 100Gb IDE drives to serve as the partition to install ubuntu on. I formatted this drive with ext4 and made it the root directory for the installation, all ok. I also have on a 1Tb SATA drive two partitions (splitting the disk in 2) one of these contains windows 7 and I did nothing to this drive (and was careful to do so) After the installation finished the computer restarted and gave me no option for choosing operating systems? what have I done wrong how can this be fixed? I would still like to be able to use Win7 for gaming. Any help on this matter would be greatly appreciated. :)

    Read the article

  • Getting a TV Capture Card working

    - by Benny Hallett
    I'm new to Linux, and am trying to get my Capture Card working on 11.04. The only command that I know to run to find out any information is lspci, which tells me that I have 02:00.0 Multimedia video controller: Conexant Systems, Inc. CX23885 PCI Video and Audio Decoder (rev 04) I've looked at using Me TV, but haven't worked out how to configure it for my card, or what I need to do to get it running. I'm not fussed on what software I use to run the Capture Card, but I've currently got only Me TV installed. Edit: When I run tvtime, I get the following errors: videoinput: Cannot open capture device /dev/video0: No such file or directory mixer: find error: Success mixer: Can't open mixer default, mixer volume and mute unavailable. mixer: Can't open device default/Line, mixer volume and mute unavailable. Segmentation fault

    Read the article

  • The annoyed configuration of java-6-openjdk

    - by kit.yang
    I want to change the java environment to java-6-openjdk. /etc/environment: PATH="/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games" JAVA_HOME=/usr/lib/jvm/java-6-openjdk/ CLASSPATH=.:$CLASSPATH:$JAVA_HOME/lib java -version: java version "1.6.0_20" OpenJDK Runtime Environment (IcedTea6 1.9.5) (6b20-1.9.5-0ubuntu1~10.04.1) OpenJDK 64-Bit Server VM (build 19.0-b09, mixed mode) javac -version:javac 1.6.0_20 But in the shell: the echo $JAVA_HOME result is /usr/lib/jvm/java-6-sun-1.6.0.22 while the $CLASSPATH is /usr/lib/jvm/java-6-sun-1.6.0.22/lib. How to find the other files in which $JAVA_HOME & $CLASSPATH value is setted by the java-6-sun-1.6.0.22 location?

    Read the article

  • Help with IPTables - Masquerading + Forwarding, 1-to-1?

    - by Artiom Chilaru
    I've got a clean Ubuntu Server 10.10 with OpenSSH, OpenVPN and vsFTPd installed. The server is running as a VM on the Hyper-V server (hypervisor), has two network interfaces mapped to physical adapters (eth0 and eth1), and a virtual interface with a direct connection to the hypervisor (eth2). The VPN will create a tun0 interface when a client connects. What I want is the remote user, connecting over VPN to be able to connect to the hypervisor (all ports, ping etc). The initial idea was to make the VPN create a tap0 interface, and bridge eth2 to tap0, but this didn't work, unfortunately, as it seems that the adapters don't want to go into promiscuous mode (partially confirmed by MS) At the same time, both the hypervisor and the remove client over VPN can successfully ping/connect to the ubuntu server with no problems. So my plan right now is to try doing some 1-1 masquerading, if possible. Basically, I want every request sent from the VPN client to the ubuntu server to be redurected to the hypervisor instead (with IP translation ofc), and every request from the hypervisor to the ubuntu machine sent to the VPN client (IP translated too). Only 1 client will be connected at a time to the VPN, so I can force limit it to a single IP at all times, if necessary. Is this the right way to go, and if true, how can this be achieved? It's almost like a special case of port-forwarding, except every single port on tun0 is forwarded to a machine in eth2, and every port on the eth2 side forwards to an ip on tun0 I guess it could be done with iptables, but I'm rather new in linux, so I can't do it myself... help? :(

    Read the article

  • How to get Broadcom BCM 43XX Wireless card working

    - by Fer1805
    NOTE - Although this question is for a specific version of Ubuntu and a specific Broadcom model, the answer to it is for most Broadcom models and versions of Ubuntu 11.04, 11.10, 12.04 and 12.10. If you have come here from another question, feel free to read the answer instead. The answer covers many problems with several solutions. I'm having serious problems installing the Broadcom drivers for Ubuntu 11.04. It worked perfectly on my previous version, but now, it is impossible. I'm a user with no advance knowledge in Linux, so I would need clear explanations on make, compile, etc. I was following the instructions on the following blog, with no luck. How can I get Broadcom BCM4311 Wireless working? Can someone help me? Edit: For the command: "lspci | grep Network", I get the following message: 06:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) For the command: iwconfig, i get the following: lo no wireless extensions. eth0 no wireless extensions. When i follow the following steps (from the above link), there are a NO error message at all: open the 'Synaptic Package Manager' and search for bcm uninstall the bcm-kernel-source package make sure that the firmware-b43-installer and the b43-fwcutter packages are installed type into terminal: cat /etc/modprobe.d/* | egrep '8180|acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl' (you may want to copy this) and see if the term blacklist bcm43xx is there if it is, type cd /etc/modprobe.d/ and then sudo gedit blacklist.conf put a # in front of the line: blacklist bcm43xx then save the file (I was getting error messages in the terminal about not being able to save, but it actually did save properly). reboot 'End of procedure' Before (not ubuntu 11.04), if i wanted to connect wireles, i just went to the icon at the upper side of the screen, click, showed ALL the wireless network available, and done. Now, the only options i see are: Wired Network Auto Eth0 Disconnect VPN Enable networking Connection information Edit connection. hope above info is enough for your help.

    Read the article

  • How can I roll back xserver-xorg-core and xserver-common?

    - by Ville Sundberg
    A recent update to Xorg broke my desktop, which now looks like this: http://i.imgur.com/PbBxh.jpg In short, the desktop background is not updating on the secondary display. (And if there is no secondary display, the primary display background stops updating.) Looking into the history, I found that this happened right after upgrading two packages: xserver-xorg-core xserver-common These were upgraded to 1.9.0-0ubuntu7.3. I'd like to downgrade these packages. How do I do that? I've checked that both have another version in the maverick repo: xserver-xorg-core: Installed: 2:1.9.0-0ubuntu7.3 Candidate: 2:1.9.0-0ubuntu7.3 Version table: *** 2:1.9.0-0ubuntu7.3 0 500 http://fi.archive.ubuntu.com/ubuntu/ maverick-updates/main amd64 Packages 100 /var/lib/dpkg/status 2:1.9.0-0ubuntu7 0 500 http://fi.archive.ubuntu.com/ubuntu/ maverick/main amd64 Packages However, apt won't let me downgrade them: ville@fluxx ~ % sudo apt-get install xserver-common=2:1.9.0-0ubuntu7 xserver-xorg-core=2:1.9.0-0ubuntu7 The following packages have unmet dependencies: xserver-xorg-core : Depends: xserver-xorg but it is not going to be installed E: Broken packages And this is the reason: ville@fluxx ~ % sudo apt-get install xserver-common=2:1.9.0-0ubuntu7 xserver-xorg-core=2:1.9.0-0ubuntu7 xserver-xorg-core The following packages have unmet dependencies: xserver-xorg-core : Depends: xserver-common (>= 2:1.9.0-0ubuntu7.3) but 2:1.9.0-0ubuntu7 is to be installed E: Broken packages Am I out of options here?

    Read the article

  • How can I track a bug that caused a crash and was reported via apport / whoopsie?

    - by nealmcb
    It used to be that when a program crashed, especially when a user was using a pre-release of Ubuntu, apport could be used to open a bug report. The user could then track the bug, see if it affected others, help fix it, etc. As of Precise 12.04, this behavior and workflow changed. As I discovered in Bug #993450 “Apport fails to submit bug report”, by default apport no longer opens a bug report (and it is awkward but not impossible to get it to do so). At the same time people are noticing a new "whoopsie" process, as described at What is the 'whoopsie' process and what does it do?. After some more googling, I dug this blueprint up, which describes the whole process: ErrorTracker - Ubuntu Wiki. (It didn't mention whoopsie or daisy, so I added them - please correct me if I got it wrong). Wow - this sounds like great work to streamline and improve the crash reporting process. I'm left with this question: how does a user learn what the status of the problem is? The blueprint now has this requirement The user should have some way to check back on the status of their crash report; e.g. have some report ID they can look at to see statistics and/or any associated bug #. E.g. provide a serial number at time of filing that they can load via a web page later on. which seems unimplemented. Is there anything available in the meantime? And how does a developer get into the game? Going to https://daisy.ubuntu.com just provides an "Incorrect Content-Type" error message. Finally, I suggest documenting the apport behavior changes in the Release Notes. It should be of interest to anyone who has been trying to help out Ubuntu.

    Read the article

  • How do I properly set up and secure a production LAMP Server?

    - by Niklas
    It's very hard to find comprehensive information on this subject. Either I found short tutorials on how you perform the installation, as simple as "apt-get install apache2", or outdated tutorials. So I was hoping I could get some professional information from my fellow members of the Ubuntu community :D I have performed a normal Ubuntu Server 11.04 with LAMP, SAMBA and SSH installed through the system installation. But I'm having some trouble setting up virtual hosts and to make the system secure enough to expose the server to the web. I've somewhat followed this tutorial this far. I have 3 sites in /etc/apache2/sites-available which all looks like this except for different site names: <VirtualHost example.com> ServerAdmin webmaster@localhost ServerAlias www.edunder.se DocumentRoot /var/www/sites/example CustomLog /var/log/apache2/www.example.com-access.log combined </VirtualHost> And I have enabled them with the command a2ensite so I have symbolic links in /etc/apache2/sites-enabled. My /etc/hosts file has these lines: 127.0.0.1 localhost 127.0.1.1 Ubuntu.lan Ubuntu 127.0.0.1 localhost.localdomain localhost example.com www.example.com 127.0.0.1 localhost.localdomain localhost example2.com www.example2.com 127.0.0.1 localhost.localdomain localhost example3.com www.example3.com And I can only access one of them from the browser (I have lynx installed on the server for testing purposes) so I guess I haven't set them up properly :) How should I proceed to get a secure and proper setup? I also use MySQL and I think that this tutorial will be enough to set up SSH securely. Please help me understanding Apache configuration better since I'm new to setting up my own server (I've only run XAMPP earlier) and please advise regarding how I should setup a firewall as well :D

    Read the article

  • Is this an apt-get issue or network issue?

    - by zharvey
    I just installed my first Ubuntu server (12.04) instance and immediately am noticing a few things: Running apt-get install or update fails (see below) Running ifconfig produces peculiar IP addresses starting with 10.x.x.x and my router does not see the server at all in its "Attached Devices" page (its a consumer grade Netgear) When I run apt-get I get 50+ of the following errors: Failed to fetch <some-http-url. Temporary failure resolving <blah.ubuntu.com I read up on this error for 12.04, and found some similar posts on this forum and on serverfault that recommended going into /etc/resolv.conf and adding an entry: nameserver 8.8.8.8 To my surprise, I found that /etc/resolve.conf was a symlink pointing to somewhere else and I had to delete it first, then create a new one with the entry indicated above. I restarted the server and tried running apt-get again: same results. How do I start diagnosing the problem (I'm a relatively new Linux/Ubuntu user)? Additional details that may help: This is actually a virtual machine running as a VirtualBox guest OS The physical host that is running this VM is my laptop which has a wireless connection; I'm wondering if (somehow) the laptop is getting the network wirelessly, but perhaps either the VBox VM and/or the Ubuntu server OS isn't configured for wireless and so nothing is "getting through"? Thanks in advance for any pointers! Edit: Here is a snapshot of my VM's Network settings (only Adapter 1 has any information populating its fields, so I assume my VM has only 1 adapter): Here is the output when I run ifconfig from the terminal: And here is the output when I run route from the terminal: Running ping google.com:

    Read the article

  • Keyboard layout - certain keys work with AltGr, other doesn't

    - by user23122
    I run Ubuntu 12.04 in VirtualBox 4.3.14 on Windows 7 with a Swedish keyboard layout. In Windows everything works fine but in Ubuntu some keys/characters (the most important for a programmer) doesn't work. This is the result from pressing the keys in the top row 1234567890+´ (Unmodified top row on keyboard) @£$€ {[]}\ (Windows with AltGr) ¡ £$€¥ ± (Ubuntu with "AltGr") More characters are broken (pipe | is a notable example) but the top row is the biggest problem. I can workaround this by enabling "direct connection" from my USB keyboard to VirtualBox but then I have to manually disable that every time I switch out of VirtualBox. I have tried different keyboard layout, sometimes @ et al works but then other characters are broken. I also tried sudo dpkg-reconfigure keyboard-configuration with default values, but it didn't change anything. I have guest additions installed (from the built in virtual CD). I got my VB disk image from a colleague who does not have this problem, however, he does not have guest additions installed (and hence can't use a higher resolution than 1024x768, and I need to run Ecplipse...). He also have different installation of Virtual Box and Windows. For example, the key for 2 should, in Ubuntu, produce four different characters, 2"²@. The first three works fine, including superscript 2 that requires AltGr-Shift-2, it is just plain AltGr-2 to get @ that does not work on this key (and all the other keys I have problem with). Any ideas for a fix?

    Read the article

  • How do I resolve "No JSON object could be decoded" on mythbuntu live CD?

    - by Neil
    I have been running a MythTV frontend on my laptop for some time against a MythTV backend installed in Linux Mint 12 on another computer, and everything works fine. Now, I'm trying out the Mythbuntu Live CD (12.04.1 32-bit) on the laptop, to turn it into a dedicated front end. It's connecting to the network just fine, and I can see my server. When I click on the frontend icon on the desktop, it asks me for the security code, which I've verified against mythtv-setup on the server. However, when I test that code, it shows the error message "No JSON object could be decoded". I've looked in the control center to see if there's something else I should be setting up. The message above implies to me that it can't find the server, but I can find no place in the control center to tell it where to find my myth backend, which I find a little odd. Does the live CD not work against a backend server on another machine?

    Read the article

  • Flash video streaming choppy for Chrome, alright for Firefox

    - by Ben
    I'm using Ubuntu 12.04.1, Chrome 21 and Firefox 15. Flash player 11.2 has been installed, and I've just started using Ubuntu... yesterday. And I'm using a Lenovo T61. The problem is that it doesn't matter if it's youtube or vimeo or some other flash player, it streams fine on chrome but every 30 seconds or so, there is a pause in video playback (with audio continuing) before it catches up, skipping quite a few seconds of video. It works perfectly fine in Firefox, and I've tried disabling PepperFlash/libpepflashplayer.so in Chrome but it doesn't seem to affect the performance. Anyone know how to work around this? It's more a problem of convenience because I don't like the idea of having to switch between Chrome and Firefox just to watch videos.

    Read the article

  • How do I change my resolution to 1600*900 for a wide screen monitor?

    - by Madhu
    How do I change my resolution to 1600*900 for a wide screen monitor in Oneiric? My Hardware configuration is as below: madhu@madhu-Home:~$ lspci 00:00.0 Host bridge: Silicon Integrated Systems [SiS] 671MX 00:01.0 PCI bridge: Silicon Integrated Systems [SiS] AGP Port (virtual PCI-to-PCI bridge) 00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS968 [MuTIOL Media IO] (rev 01) 00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev 01) 00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f) 00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f) 00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller 00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] 191 Gigabit Ethernet Adapter (rev 02) 00:05.0 IDE interface: Silicon Integrated Systems [SiS] SATA Controller / IDE mode (rev 03) 00:06.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge 00:07.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge 00:0f.0 Audio device: Silicon Integrated Systems [SiS] Azalia Audio Controller 00:1f.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge 01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 771/671 PCIE VGA Display Adapter (rev 10) madhu@madhu-Home:~$ cat /etc/X11/xorg.conf

    Read the article

  • JUJU and ERROR environment has no access-key or secret-key

    - by Riccardo Magrini
    following the official guide: [1]https://juju.ubuntu.com/docs/config-maas.html and considered that I've generated the ssh key (added it to UI of MAAS) and the API key, my environments.yaml file presents in this way: environments: maas: type: maas maas-server: 'http://x.x.x.x/MAAS/' maas-oauth: 'NDPA86PsEzS7bFynSy:vqJLkyHUJbvYzbtY5Q:sXXXXXXXXXXXXXXXXXXXXXX admin-secret: 'nothing' default-series: precise authorized-keys-path: ~/.ssh/id_rsa.pub # or any file you want. when I try to run the command: juju bootstrap receive the following error: ERROR environment has no access-key or secret-key Someone can explain me where is the wrong? MAAS and JUJU are installed using their ppa stable on an Ubuntu 12.04.3 Server

    Read the article

  • Dock with dual external DVI monitors with Intel + Nvidia Optimus?

    - by Ryan
    I have a Dell Latitude E6420 laptop plugged into a docking station, and the dock has 2 monitors (connected with DVI). Also note that I've installed Ubuntu alongside (dual-boot) Windows 7. I can't get the dual monitors to work both on Ubuntu (either 11.10 or 12.04) and Windows 7. When I run lspci | grep VGA, I get: 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 01:00.0 VGA compatible controller: nVidia Corporation GF108 [Quadro NVS 4200M] (rev a1) If I then reboot and uncheck Optimus setting in the BIOS during reboot, I'm able to get the dual monitors to work in Ubuntu 12.04 (but I need to configure them every boot in Nvidia Settings). When I run lspci | grep VGA, I get: 01:00.0 VGA compatible controller: NVIDIA Corporation GF119 [Quadro NVS 4200M] (rev a1) But then if I reboot into Windows (leaving the Optimus unchecked), Windows can't detect external monitors, and the resolution is unacceptably low. I've seen on many forum posts that this particular graphics card setup causes lots of headaches. I haven't been able to resolve my problem yet. How can I use my external display on my laptop with intel and nvidia video cards? How to use external displays with Intel driver on a NVidia/Intel hybrid system nVidia Optimus , Unity 3D and Dual Monitors "Just use VGA instead of DVI" isn't an option because my dock has only 1 VGA port (and 2 DVI). Switching the BIOS setting on every reboot and then reconfiguring the display settings every time is tedious, time-consuming, and impractical. Do you know how to make this work smoothly? Thanks for your help! P.S. see also: http://superuser.com/questions/434358/dell-latitude-e6420-dual-boot-ubuntu-windows-7-optimus-graphics-problems

    Read the article

  • Add Windows 7 to boot menu

    - by Cumatru
    Device Boot Start End Blocks Id System /dev/sda1 * 1 13 102400 7 HPFS/NTFS - system restore /dev/sda2 13 4674 37436416 7 HPFS/NTFS - Windows 7 /dev/sda3 4674 58843 435116032 7 HPFS/NTFS - data storage /dev/sda4 58843 60802 15728640 83 Linux - Ubuntu 10.10 Initially i´ve installed StartUpManager. This ( i think ) added another 4 instances of Linux + memtest to my boot menu list. Altough, i din´t see any boot menu. It boots into Ubuntu after a few seconds. I´ve tried to add windows 7, but i did not succeed. This is a part of my menu.lst file. title Ubuntu 10.10, kernel 2.6.35-24-generic uuid 1c9748e2-2f11-4a6c-91c0-7310d48c4a7a kernel /boot/vmlinuz-2.6.35-24-generic root=UUID=1c9748e2-2f11-4a6c-91c0-7310d48c4a7a ro quiet splash initrd /boot/initrd.img-2.6.35-24-generic title Chainload into GRUB 2 root 1c9748e2-2f11-4a6c-91c0-7310d48c4a7a kernel /boot/grub/core.img title Ubuntu 10.10, memtest86+ uuid 1c9748e2-2f11-4a6c-91c0-7310d48c4a7a kernel /boot/memtest86+.bin menuentry “Windows 7? { set root=(hd0,2) chainloader +1 } And this is after a upgrade-grub Searching for GRUB installation directory ... found: /boot/grub Searching for default file ... found: /boot/grub/default Testing for an existing GRUB menu.lst file ... found: /boot/grub/menu.lst Searching for splash image ... none found, skipping ... Found kernel: /boot/vmlinuz-2.6.35-24-generic Found kernel: /boot/vmlinuz-2.6.35-22-generic Found GRUB 2: /boot/grub/core.img Found kernel: /boot/memtest86+.bin Updating /boot/grub/menu.lst ... done Later Edit: Ive added the following in 40_custom from /etc/grub.d/ and ive decommented hidden menu line from menu.lst, but i still cant see any boot menu. Ive also tried to press ESC and SHIFT. menuentry "Windows 7 (loader) (on /dev/sda1)" { insmod part_msdos insmod ntfs set root='(hd0,msdos1)' chainloader +1 } menuentry "Windows 7 (loader) (on /dev/sda1)" { insmod part_msdos insmod ntfs set root='(hd0,msdos0)' chainloader +1 } menuentry "Windows 7 (loader) (on /dev/sda1)" { set root= hd(0,0) chainloader +1 } menuentry "!Windows 7 (loader) (on /dev/sda1)" { set root= hd(0,1) chainloader +1 } menuentry "!!Windows 7 (loader) (on /dev/sda1)" { set root= hd(0,2) chainloader +1 }

    Read the article

< Previous Page | 497 498 499 500 501 502 503 504 505 506 507 508  | Next Page >