Search Results

Search found 1798 results on 72 pages for 'incoming'.

Page 51/72 | < Previous Page | 47 48 49 50 51 52 53 54 55 56 57 58  | Next Page >

  • Centos IPTables configuration for external firewall

    - by user137974
    Current setup Centos which is a Web, Mail (Postfix,Dovecot), FTP Server and Gateway with public ip and private ip (for LAN Gateway). We are planning to implement external firewall box and bring the server to LAN Please guide on configuring IPTables... Unable to receive mail and outgoing mail stays in postfix queue and is sent after delaying... The local ip of the server is 192.168.1.220 iptables -P INPUT DROP iptables -P FORWARD DROP iptables -P OUTPUT DROP incoming HTTP iptables -A INPUT -i eth0 -p tcp --dport 80 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 80 -m state --state ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --dport 443 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 443 -m state --state ESTABLISHED -j ACCEPT outgoing HTTP iptables -A OUTPUT -o eth0 -p tcp --dport 80 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --sport 80 -m state --state ESTABLISHED -j ACCEPT FTP iptables -A INPUT -p tcp -s 0/0 --sport 1024:65535 -d 192.168.1.220 --dport 21 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp -s 192.168.1.220 --sport 21 -d 0/0 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT iptables -A INPUT -p tcp -s 0/0 --sport 1024:65535 -d 192.168.1.220 --dport 1024:65535 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A OUTPUT -p tcp -s 192.168.1.220 --sport 1024:65535 -d 0/0 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT SMTP iptables -A INPUT -p tcp -s 0/0 --sport 1024:65535 -d 192.168.1.220 --dport 25 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp -s 192.168.1.220 --sport 25 -d 0/0 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp -s 192.168.1.220 --sport 1024:65535 -d 0/0 --dport 25 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -p tcp -s 0/0 --sport 25 -d 192.168.1.220 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT POP3 iptables -A INPUT -p tcp -s 0/0 --sport 1024:65535 -d 192.168.1.220 --dport 110 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp -s 192.168.1.220 --sport 110 -d 0/0 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT

    Read the article

  • Networking "chokes" on Windows 7 64 bit

    - by Rohit Nair
    I've been having this problem for some months now, and I have been unable to figure out a solution, or even the cause. At random points throughout the day, my internet connectivity "freezes". I don't get disconnected from my local wireless network. My router doesn't get disconnected from the world. However, for some reason, my computer stops receiving packets. If I'm playing an MMO ( World of Warcraft, in this case, but it has happened with Eve Online as well ) all activity just freezes. If I try to browse, Opera, Firefox and IE all stall at "Waiting for google.com..." or whatever the hostname may be. Inspection with a packet sniffer seems to reveal that there are no incoming packets. Here's the interesting part. Disconnecting from my wireless network and reconnecting fixes the issue. Obviously this led me to conclude that it was a problem with my router or wireless card. However, I have tweaked all the settings on my router that I could think of, including things like QoS, AP Isolation, etc. with no change. My wireless card doesn't really have that many options, and I have uninstalled and reinstalled drivers a few times without any change. Windows Firewall on/off doesn't make a difference. Anyone have any suggestions for debugging this? It's becoming an annoyance.

    Read the article

  • Looking for a help desk ticketing system..

    - by Dan
    Hi guys Im looking for a good help desk ticket solution. It must perform the following actions for it to be useful. It needs to have a single point of contact via email..e.g [email protected] If we recieve a telephone(or an email outside of the system) we need to be able to create a ticket as if had been added via the single point of contact, this needs to be done with ease in order to save time. Certain people within our organisation deal with certain customers, so if the email/ custom input support call as mentioned in bullet 2 is picked up as having a relationship with that certain person in our organisation it needs to be sent to them/put in their queue for them to work on. If a person is out of office or sick any tickets sent to them must be forwarded to somebody else or put into a seperate pool of tickets that anybody can access. Perhaps have an agent that sorts through tickets in the pool and assigns them to anybody who is available, preferably the person with fewest tickets in their queue/list. Once a customer emails and the system logs it they immediately get a response with a ticket number and maybe details of who is dealing with the problem. Any correspondance in relation to a particular ticket is automatically grouped into some sort of message, and not made into a load of separate tickets. I.e system scans incoming email subjects for ticket numbers and assosciates it with exisiting tickets if that number exists. Any help is much appreciated Thanks P.S I have taken a look at OTRS but i'm not feeling it so unless someone can convince me I guess i'm after an alternative.

    Read the article

  • Mail.app doesn't detect sender in Address Book

    - by CoreSandello
    Hi there. I don't understand, how does 'smart addresses' in Mail.app work. Recently I mentioned, that for some emails I don't see person's full name in 'From' column. I started to dig into this behavior and found out, that I have few contacts in my Address Book, that are not recognized by Mail.app. Here how it looks: I have a person in Address Book with filled email entry and filled first/last name (localized). I have an incoming email from that person (from email specified in Address Book), but first/last name in the email itself doesn't match with ones specified in Address Book (e. g. 'From' field in email looks like 'John [work] <[email protected]>' while Address Book entry is 'John Smith' (localized, in Russian)). And Mail.app doesn't recognize that this mail is originating from that person in Address Book: if I click on 'From' field, it suggests to me to add sender to Address Book, while for others' emails I have 'Show in Address Book' menu entry (especially for ones with full localized name in 'From' field). I'm wondering, is that behavior correct or I'm missing something? I'm using Snow Leopard & Mail 4.0; my system language set to English, if that matters. I'd like to have some clarifications on that Mail.app behavior: whenever it fixable or not (and if it's fixable, I'd like to see a fix). By the way, is it possible to match sender's address against Address Book entry in filter rules or not? That would be great, if I can create rules like 'move all mail from that person to that folder' without specifying exact source address. Thanks, Ivan.

    Read the article

  • AWS lighttpd: Sending a copy of requests to test.

    - by Martin
    I have a load balanced service on AWS. So the ELB evenly distributes the load across my servers. Each server is running lighttpd that does logging and forwards the requests to my service (on the same machine). I have written a new version of the service. It is installed and running on an EC2 machine test1 (basically a mirror of our current server but the new service running instead of the original) and I have done some preliminary tests that look good. But what I would like to do is mirror a fraction of incoming traffic to the new version of the service so I can do some comparisons between an original version and the new version based on real traffic. Thus I was thinking I could modify one box behind the ELB to duplicate its traffic to the test1. I was thinking I could modify the configuration of lighttpd so that each request is mirrored/duplicated. i.e. the original service keeps responding as before but a mirror request is sent to test1 but the reply is just dropped). Unfortunately I have not been able to work this out. Any ideas on how I could mirror the requests from one box to itself and test1. Or any other ideas for testing.

    Read the article

  • How can I explain to dspam that the user "brandon" is the same as "brandon@mydomain"

    - by Brandon Craig Rhodes
    I am using dspam for spam filtering by running the "dspamd" daemon under Ubuntu 9.10 and then setting up a Postfix rule that says: smtpd_recipient_restrictions = ... check_client_access pcre:/etc/postfix/dspam_everything ... where that PCRE map looks like this: /./ FILTER lmtp:[127.0.0.1]:11124 This works well, and means that all users on my system get all of their email, whether "dspam" thinks it is innocent or not, and have the option of filtering on its decisions or ignoring them. The problem comes when I want to train dspam using my email archives. After reading about the "dspam" command, I tried this on the files in my Inbox and spam boxes (which date from when I was using another filtering solution): for file in Mail/Inbox/*; do cat $file | dspam --class=innocent --source=corpus; done for file in Mail/spam/*; do cat $file | dspam --class=spam --source=corpus; done The symptom I noticed after doing all of this was that dspam was horrible at classifying spam — it couldn't find any! The problem, when I tracked it down, was that I was training the user "brandon" with the above commands, but the incoming email was instead compared against the username "brandon@mydomain", so it was running against a completely empty training database! So, what can I do to make the above commands actually train my fully-qualified email address rather than my bare username? I would like to avoid having to run "dspam" as root with a "--user" option. I would have expected that the "dspam" configuration files would have had an "append_domain" attribute or something with which to decorate local usernames with an appropriate email domain, but I can't find any such thing. When I used to use the Berkeley DB backend to "dspam", I solved this problem by creating a symlink from one of the databases to the other. :-) But that solution eventually died because the BDB backend is not thread-safe, so now I have moved to the PostgreSQL back-end and need a way to solve the problem there. And, no, the table where it keeps usernames has a UNIQUE constraint that prevents me from listing both usernames as mapping to the same ID. :-)

    Read the article

  • Wordpress hacked. Disabled hacked site but bad traffic continues [closed]

    - by tetranz
    Possible Duplicate: My server's been hacked EMERGENCY My Ubuntu 10.04 LTS VPS has been hacked, probably via a WordPress site. I was alerted to it when I noticed the incoming traffic was unusually high. A WordPress site was littered with eval(base64_decode(...)) code in lots of files. My fault, I had some files writeable by www-data which shouldn't have been. I've disabled that site (a2dissite ... and restart Apache). This has reduced it but I am still getting some malware type traffic. My server runs several WordPress and Drupal sites and a home grown PHP site. I have captured traffic with tcpdump and looked at it Wireshark. It's reaching out to the login page of some Joomla sites, trying multiple logins. The traffic stops when I stop Apache. If I a2dissite every site and reload (not restart) Apache the traffic continues. At that point I have no virtual hosts running and no DocumentRoot in my apache2.conf so I don't know how Apache is still running something. I have searched the other sites with grep for likely looking php code with no success. I may have missed it but I haven't found anything suspicious in the Apache logs. I have mod-status running. I haven't really seen anything much there except that someone is still trying to do a POST to the theme page on the disabled WordPress site but they now get a 404. What should I be looking for? Are there any tools or whatever which would give me more info about how Apache is generating that traffic? Thanks

    Read the article

  • Postfix: change sender in queued messages

    - by ring0
    Following a complete re-installation we got a problem with the configuration: the sender address was wrong and some recipients (mail servers) rejected them. So there is a bunch of mails stuck in the Postfix queue. Ideally, a change of the sender address directly in the queued mails, and then flushing the queue would be optimal. I tried this answer that addresses this very problem. But messages don't seem to be easily modifiable in the version I have (2.11.0). For instance there is no /var/spool/mqueue dir, but, instead, /var/spool/postfix/... active bounce corrupt defer deferred dev etc flush hold incoming lib maildrop pid private public saved trace usr and the dir of interest is deferred. I tried to modify a few files there changing the wrong domain with the correct one (and was careful to ensure only those were changed). But then, those mails were moved to corrupt, meaning that a simple text change doesn't seem to work (done with vi). Any other cleaner way to change the sender in queued mails?

    Read the article

  • System Idle Process network traffic?-Updated

    - by Moab
    I was using NetBalancer and noticed network traffic on an unidentified service, but when I highlight it and then go to the lower center pane and click the parent process it says it is the System Idle process, it is showing incoming and outgoing traffic in the upper pane, anyone know why this Windows System Idle Process is talking on the network? Windows 7 HP 64bit . . . Edit, after blocking the traffic for that unidentified Service I checked my event viewer (Windows LogsSystem) and found 3 new events that were never recorded before and matched the time I blocked the traffic. So is this part of the Windows local DNS cache? Event ID 1014 DNS Client Events Name resolution for the name dns.msftncsi.com timed out after none of the configured DNS servers responded. dns.msftncsi.com Name resolution for the name wpad.home timed out after none of the configured DNS servers responded. wpad Name resolution for the name mscrl.microsoft.com timed out after none of the configured DNS servers responded. mscrl.microsoft.com . Then My Web Browser refused to work, I re-enabled the traffic and all returned to normal. .

    Read the article

  • Cannot establish a network connect to VMWare Fusion VM

    - by twolfe18
    I am running Snow Leopard 10.6.2 (not the server edition) with VMWare Fusion 3.0.0 and I trying to get my Ubuntu 9.10 x86_64 VM working. I am using a bridged connection, and I have an internet connection FROM the Ubuntu VM (I can download updates, ping websites, etc), but I cannot connect TO the Ubuntu box from any other device on my network. I am trying to get Mongrel up on the Ubuntu VM for some Rails stuff, but it's not working. I know Mongrel/Rails is not the problem because if I start the server on the Ubuntu VM, background the process, and then wget the index page, it works. I just cannot connect to the site from another IP. I have tried using a static IP and a DHCP IP configuration on the Ubuntu VM, neither work (for incoming connections, both work for outwards). I have port scanned the Ubuntu VM, and it appears that all ports are closed. However, the Ubuntu VM does respond to pings. I noticed a similar question here: http://serverfault.com/questions/99757/setting-up-a-bridged-network-with-vmware-fusion, but no answer. Any ideas?

    Read the article

  • Domain authentication over OPEN wireless pre-logon (Windows 7 Pro) - No logon servers avail

    - by Shadow00Caster
    I have a plethora of laptops that are joined to an AD domain. I have an enterprise wireless system setup, the users of these laptops will be using an OPEN unsecured SSID which will ultimately have a captive portal that uses Radius-AD auth and firewall rules to allow access pre-captive portal auth to the proper ip's/ports of DC's etc for auth etc. I already have other laptops/users connecting to another SSID with 802.11x and SSO, all works perfectly pre-logon etc. My problem is with this open network, for some reason I cannot get the machines to auth to AD. The laptops connect to the wireless network, I confirm this on the controller and can ping the laptop at startup. I sharked the wires on the 2 DC's that these machines auth to, I can see a DNS SOA update from a laptop im testing with and can ping that test laptop from both DC's. When I try to logon, "There are currently no logon servers available to service the logon request." The shark shows no incoming connections to either DC even though the laptop is connected and pingable. Any help is greatly appreciated.

    Read the article

  • Configuring DNS & MX records for exchange 2010

    - by Mahmoud Saleh
    i am trying to configure Exchange Server 2010 on Windows Server 2008 R2 to receive emails from the internet following the danscourses tutorials: and i followed this video for the DNS & MX records: http://www.youtube.com/watch?v=jdf_3DRssks i don't have any windows administration skills, and i am stuck with the DNS configuration. and the following are my domain configuration i got from the hosting. following are the steps i made: 1- Add new name server: add ns1.centors.com ip Exchange Server Public IP: 41.233.26.131 2- Change the A record change it to point to the public ip address Exchange Server Public IP: 41.233.26.131 3- New cname record for www and make it resolve to centors.com 4- New mx record for mail.centors.com 5- New A record for mail.centors.com: name: mail ip: Exchange Server Public IP: 41.233.26.131 6- new A record for ns1: ip: Exchange Server Public IP: 41.233.26.131 7- i made port forward in the router for SMTP and POP3 to the exchange server local ip address. ISSUE: i have a user account in the active directory, and the user is member of the domain, the user is [email protected] and when trying to login with this account in outlook 2010 on other machine using following data: account type: POP3 incoming mail server: mail.centors.com outgoing mail server: mail.centors.com i always get the error: Authorization failed, check your server settings. please advise what's wrong with the configuration, thanks in advance.

    Read the article

  • Windows update stuck. Fixt it stuck. So is KB947821. What should I do?

    - by Jim Thio
    I installed a new computer. After I installed I update everything and let the computer runs for days. Then I don't know what my daughter do. The computer stop responding. Windows update no longer work. People said to run fix it. Fix it run and after that the problem still persist and it still doesn't work. The problem changes though. Before there is some error code. Now windows update simply "updating" never end. So I downloaded KB947821. It's been 3 hour and it's still installing. Looks like it hit firewall or something. i don't see windows update on firewall exception list. However, I've never heard that this is an issue. Firewall only protect against incoming transaction, not outgoing right? Or what am I missing. What should I do?

    Read the article

  • Packet drop measured by ethtool, tcpdump and ifconfig

    - by Rayne
    Hi all, I have a question regarding packet drops. I am running a test to determine when packet drops occur. I'm using a Spirent TestCenter through a switch (necessary to aggregate Ethernet traffic from 5 ports to one optical link) to a server using a Myricom card. While running my test, if the input rate is below a certain value, ethtool does not report any drop (except dropped_multicast_filtered which is incrementing at a very slow rate). However, tcpdump reports X number of packets "dropped by kernel". Then if I increase the input rate, ethtool reports drops but "ifconfig eth2" does not. In fact, ifconfig doesn't seem to report any packet drops at all. Do they all measure packet drops at different "levels", i.e. ethtool at the NIC level, tcpdump at the kernel level etc? And am I right to say that in the journey of an incoming packet, the NIC level is the "so-called" first level, then the kernel, then the user application? So any packet drop is likely to happen first at the NIC, then the kernel, then the user application? So if there is no packet drop at the NIC, but packet drop at the kernel, then the bottleneck is not at the NIC? Thank you. Regards, Rayne

    Read the article

  • Port translation in router causing some email to fail

    - by user22037
    We are in the process of setting up a spam filter (SAVASM). One change we are making is to push incoming email on port 25 through our spam filter/server but have users actually send their email on a different port. I am attempting to make this happen by using port address translation to send port 25 traffic to the SAVASM server IP. As a step in making this change I setup port translation without actually changing the IP addresses. The NAT rules for the email server went from one Static NAT rule with no port specified, to multiple Static NAT rules each with a port or group matching the Access Rules for that server (smtp, pop3, http, https, and some other custom ports). The problem we are running into is confusing. Some outgoing mail through this server is failing when the router has the multiple NAT rules with port translation settings. Email goes through fine FROM our email to our internal accounts and to Gmail. However email fails when FROM our client's email address TO our client's email or their personal Comcast. The only situation that worked for them was if they changed FROM to Comcast and then messages went through fine to both Comcast and the client's accounts. Switching back to regular Static NAT rule everything then worked for them. Does anyone have a clue as to what might be going on? We are on a Cisco ASA 5500 box.

    Read the article

  • Request bursting from web application Load Tests

    - by MaseBase
    I'm migrating our web and database hosting to a new environment on all new machines. I've recently performed a Load Test using WAPT to generate load from multiple distributed clients. The server has plenty of room to handle the traffic load, but I'm seeing an odd pattern of incoming traffic during the load tests. Here is the gist of our setup: Firewall server running MS Forefront TMG 2010 on Win 2k8 server Request routing done by IIS Application Request Routing on firewall machine Web server is a Hyper-V VM on the Database server (which is the host OS) These machines are hefty with dual-CPU's with six cores (12 total procs) Web server running IIS 7.5 Web applications built in ASP.NET 2.0, with 1 ISAPI filter (Url Rewrite) in front What I'm seeing during the load tests is that the requests all come through in bursts. Even though I have 7 different distributed clients sending traffic loads, the requests come through about 300-500 requests at a time. The performance monitor shows nearly all of the counters moving through this pattern, where a burst of requests comes in the req/sec jumps to 70, the queued requests jumps to 500, the current requests jumps up, the CPU jumps up, everything. Then once it's handled that group of requests, it has a lull for nearly 10 seconds where nearly nothing is happening. 0-5 req/sec, 0 queued requests, minimal CPU usage. Then after 10 seconds of inactivity, another burst comes through, spiking all of the counters once again. What I can't figure out is why the requests are coming through in bursts when I know that the load being generated is not sent that way, especially considering the various load-generating clients sending traffic all in different intervals with random think time's between each request. Is there something in the layers between Hyper-V or perhaps in the hardware which might cause this coalesce of requests together? Here is what i'm looking at, the highlighted metric is Requests/sec, but the others critical counter go with it: Requests Queued (which I'd obviously like to keep as close to 0 as possible). Any ideas on this?

    Read the article

  • BGP Multipath & return routes

    - by Dennis van der Stelt
    I'm probably a complete n00b concerning serverfault related questions, but our IT department makes a bold statement I wish to verify. I've searched the internet, but can find nothing related to my question, so I come here. We have Threat Management Gateway 2010 and we used to just route the request to IIS and it contained the ip address so we could see where it was coming from. But now they turned on "Requests apear to come the TMG server" so ip addresses aren't forwarded anymore. Every request has the ip of the TMG server. Now the idea behind this is that because of multipath bgp routes, the incoming request goes over RouteA, but the acknowledgement messages could return over RouteB. The claim is that because the request doesn't come from the first known source, our proxy, but instead from IIS, some smart routers at the visitor of our websites don't recognize the acknowledgement message and filter it out. In other words, the response never arrives. Again, this is the claim. But I cannot find ANY resources on the internet that support this claim. I do read about bgp multipath, but more in the case that there are alternative routes when the fastest route fails for some reason. So is the claim completely bogus or is there (some) truth to it? Can someone explain or point me to resources? Thanks in advance!

    Read the article

  • How to balance the root domain using NS records?

    - by Patrick McCurley
    I have two load balancers that balance incoming traffic across multiple data centers. These work fine. I can test them out by doing an 'nslookup mydomain.com xIP' I have now taken out DNS services with DYN.com to allow me to manage the DNS Zone file so that typing mydomain.com will ask my load balancers what the IP address is to resolve. Step 1 : the NS record for www. I set up A records (glue) for ns1 & ns2, then the corresponding NS record to delegate the DNS lookup to the balancers instead of DYN.com's nameservers. ns1.mydomain.com A [ip address of load balancer 1] ns2.mydomain.com A [ip address of load balancer 1] www.mydomain.com NS ns1.mydomain.com www.mydomain.com NS ns2.mydomain.com All is well - when I type www.mydomain.com, the requests get delegated to my load balancers who provide the IP address of the endpoint and the connect is made successfully. Step 2 : the NS record for root. This is where I run into problems. I need customers to be able to type 'mydomain.com' (without the www) and ALSO get delegated to the load balancers for the IP address. However - of the research I have done, and through the DYN control panel, it seems to be not allowed to provide an NS record for the root - as this overrides the default NS servers. How can i delegate both the root, and the www. to my load balancers?

    Read the article

  • Configure Windows firewall to prevent an application from listening on a specific port

    - by U-D13
    The issue: there are many applications struggling to listen on port 80 (Skype, Teamviewer et al.), and to many of them that even is not essential (in the sense that you can have a httpd running and blocking the http port, and the other application won't even squeak about being unable to open the port). What makes things worse, some of the apps are... Well, I suppose, that it's okay that the mentally impaired are being integrated in the society by giving them a job to do, but... Programming requires some intellectual effort, in my humble opinion... What I mean is that there is no way to configure the app not to use specific ports (that's what you get for using proprietary software) - you can either add it to windows firewall exceptions (and succumb to undesired port opening behavior) or not (and risk losing most - if not all - of the functionality). Technically, it is not impossible for the firewall to deny an application opening an incoming port even if the application is in the exception list. And if this functionality is built into the Windows firewall somewhere, there should be a way to activate it. So, what I want to know is: whether there exists such an option, and if it does how to activate it.

    Read the article

  • Best Practical RT, sorting email into queues automatically using procmail

    - by user52095
    I'm trying to get incoming e-mail to automatically go directly into whichever queue/ticket they are related to or create a new one if none exist and the right queue e-mail setup in the web interface is used. I will have too many queues to have two line items within mailgate per queue. A similar issue was discussed here (http://serverfault.com/questions/104779/procmail-pipe-to-program-otherwise-return-error-to-sender), but I thought it best to open a new case instead of tagging on what appeared to be an answer to that person's query. I'm able to send and receive e-mail (via PostFix) to the default rt user and this user successfully accepts all e-mail for the relative domain. I have no idea where the e-mail goes - it's successfully delivered, but it does not update existing tickets (with a Subject line match) and it does not create any new. Here's and example of my ./procmail.log: procmail: [23048] Mon Aug 23 14:26:01 2010 procmail: Assigning "MAILDOMAIN=rt.mydomain.com " procmail: Assigning "RT_MAILGATE=/opt/rt3/bin/rt-mailgate " procmail: Assigning "RT_URL=http://rt.mydomain.com/ " procmail: Assigning "LOGABSTRACT=all " procmail: Skipped " " procmail: Skipped " " procmail: Assigning "LASTFOLDER={ " procmail: Opening "{ " procmail: Acquiring kernel-lock procmail: Notified comsat: "rt@18337:./{ " From [email protected] Mon Aug 23 14:26:01 2010 Subject: RE: [RT.mydomain.com #1] Test Ticket Folder: { 1616 Does the notified comsat portion mean that it notified RT? The contents of my ./procmailrc: #Preliminaries SHELL=/bin/sh #Use the Bourne shell (check your path!) #MAILDIR=${HOME} #First check what your mail directory is! MAILDIR="/var/mail/rt/" LOGFILE="home/rt//procmail.log" LOG="--- Logging ${LOGFILE} for ${LOGNAME}, " VERBOSE=yes MAILDOMAIN="rt.mydomain.com" RT_MAILGATE="/opt/rt3/bin/rt-mailgate" #RT_MAILGATE="/usr/local/bin/rt-mailgate" RT_URL="http://rt.mydomain.com/" LOGABSTRACT=all :0 { # the following line extracts the recipient from Received-headers. # Simply using the To: does not work, as tickets are often created # by sending a CC/BCC to RT TO=`formail -c -xReceived: |grep $MAILDOMAIN |sed -e 's/.*for *<*\(.*\)>* *;.*$/\1/'` QUEUE=`echo $TO| $HOME/get_queue.pl` ACTION=`echo $TO| $HOME/get_action.pl` :0 h b w |/usr/bin/perl $RT_MAILGATE --queue $QUEUE --action $ACTION --url $RT_URL } I know that my get_queue.pl and get_action.pl scripts work, as those have been previously tested. Any help and/or guidance you can give would be greatly appreciated. Nicôle

    Read the article

  • IPTables: NAT multiple IPs to one public IP

    - by Kaemmelot
    I'm looking for a way how to nat 2 or more inner IPs (in my case xen doms) to one outer IP. I tried to use iptables -t nat -A PREROUTING -d 123.123.123.123 -j DNAT --to 1.2.3.4 --to 1.2.3.7 iptables -t nat -A POSTROUTING -s 1.2.3.4 -j SNAT --to 123.123.123.123 iptables -t nat -A POSTROUTING -s 1.2.3.7 -j SNAT --to 123.123.123.123 And got an error: iptables v1.4.14: DNAT: Multiple --to-destination not supported Try `iptables -h' or 'iptables --help' for more information. I found this in the manpage: Later Kernels (= 2.6.11-rc1) don't have the ability to NAT to multiple ranges anymore. So my question is: Why is it not possible anymore and is there a workaround? Maybe I should use an other method I don't know yet? EDIT: The idea is to use the system like a router, so I have one address but multiple users behind. The problem is I don't know which connection reffers to a user (for example 1.2.3.4). But I know, they all have different ports open for incomming traffic. So my solution (for DNAT) would be to nat all incoming connections to all users and filter all unused ports, so the connection goes to one single user. For outgoing traffic I would use iptables -A FORWARD -i eth0 -d 1.2.3.4 -m state --state ESTABLISHED,RELATED -j ACCEPT

    Read the article

  • New AD-DC in a new Site is refusing cross-site IPv4 connections

    - by sysadmin1138
    We just added a new Server 2008 (sp2) Domain Controller in a new Site, our first such config. It's over a VPN gateway WAN (10Mbit). Unfortunately it is displaying a strange network symptom. Connections to the SMB ports (TCP/139 and TCP/445) are being actively refused... if the connection is coming in on pure IPv4. If the incoming connection is coming by way of the 6to4 tunnel those connections establish and work just fine. It isn't the Firewall, since this behavior can be replicated with the firewall turned off. Also, it's actually issuing RST packets to connection attempts; something that only happens with a Windows Firewall if there is a service behind a port and the service itself denies access. I doubt it's some firewall device on the wire, since the server this one replaced was running Samba and access to it from our main network functioned just fine. I'm thinking it might have something to do with the Subnet lists in AD Sites & Services, but I'm not sure. We haven't put any IPv6 addresses in there, just v4, and it's the v4 connections that are being denied. Unfortunately, I can't figure this out. We need to be able to talk to this DC from the main campus. Is there some kind of site-based SMB-level filtering going on? I can talk to the DC's on campus just fine, but that's over that v6 tunnel. I don't have access to a regular machine on that remote subnet, which limits my ability to test.

    Read the article

  • How to make gpg2 to flush the stream?

    - by Vi
    I want to get some slowly flowing data saved in encrypted form at the device which can be turned off abruptly. But gpg2 seems to not to flush it's output frequently and I get broken files when I try to read such truncated file. vi@vi-notebook:~$ cat asdkfgmafl asdkfgmafl ggggg ggggg 2342 2342 cat behaves normally. I see the output right after input. vi@vi-notebook:~$ gpg2 -er _Vi --batch ?pE??x...(more binary data here)....???-??.... asdfsadf 22223 sdfsdfasf Still no data... Still no output... ^C gpg: signal Interrupt caught ... exiting vi@vi-notebook:~$ gpg2 -er _Vi --batch /tmp/qqq skdmfasldf gkvmdfwwerwer zfzdfdsfl ^\ gpg: signal Quit caught ... exiting Quit vi@vi-notebook:~$ gpg2 < /tmp/qqq You need a passphrase to unlock the secret key for user: "Vitaly Shukela (_Vi) " 2048-bit ELG key, ID 78F446CA, created 2008-01-06 (main key ID 1735A052) gpg: [don't know]: 1st length byte missing vi@vi-notebook:~$ # Where is my "skdmfasldf" How to make gpg2 to handle such case? I want it to put enough output to reconstruct each incoming chunk of input. (Also fsyncing after each output can be benefitial as an additional option). Should I use other tool (I need pubkey encryption).

    Read the article

  • Strange ASP.NET Queue Performance Counters Behavior?

    - by LemurTech
    We have an ASP.NET 2.0 site running in classic mode. I am seeing very strange behavior in the performance counter values. Perhaps these are bugs (I've been all over Google trying to verify this, without much luck), or perhaps it is just my inexperience with monitoring these things. This PerfMon graph (http://imgur.com/Jv5io5J) represents a load test where I add up to 350 virtual users to the site, at a rate of about 1/sec, performing relatively simple page browsing. At the end of the test, I gradually taper off the number of users. This is a 4 CPU server. Machine.config settings for are at the defaults. The solid blue line is ASP.NET Apps v2.x\Requests Executing for the application in question. The profile makes perfect sense, with a quick ramp-up to 32 executing requests (minWorkerThreads x 4CPUs), followed by a slower ramp-up to 48 ((maxWorkerThreads - minWorkerThreads) x 4CPUs). The solid yellow line is ASP.NET v2.x\Requests Queued. Again, this makes sense: after the initial 32 request threads are activated, the queue begins to build as new thread initialization can't keep pace with incoming requests. But as executing requests reaches its highest possible value of 48, the counter for ASP.NET Apps v2.x\Requests Queued (green solid line) suddenly springs to life and maintains step with the yellow counter. As far as I can tell, and with no other apps running on the server, these two counters should have had the same values from the start. One other odd thing: The counter for ASP.NET v2.x\Request Wait Time (dotted yellow line) also does not spring to life until executing requests reaches 48. Shouldn't I be seeing values here from the moment ASP.NET v2.x\Requests Queued begins to build? And likewise, why would ASP.NET Apps v2.x\Request Execution Time (dotted blue) increase significantly only after that peak of 48 is reached? Shouldn't it ramp-up gradually along with queued requests?

    Read the article

  • nginx reverse ssl proxy with multiple subdomains

    - by BrianM
    I'm trying to locate a high level configuration example for my current situation. We have a wildcard SSL certificate for multiple subdomains which are on several internal IIS servers. site1.example.com (X.X.X.194) -> IISServer01:8081 site2.example.com (X.X.X.194) -> IISServer01:8082 site3.example.com (X.X.X.194) -> IISServer02:8083 I am looking to handle the incoming SSL traffic through one server entry and then pass on the specific domain to the internal IIS application. It seems I have 2 options: Code a location section for each subdomain (seems messy from the examples I have found) Forward the unencrypted traffic back to the same nginx server configured with different server entries for each subdomain hostname. (At least this appears to be an option). My ultimate goal is to consolidate much of our SSL traffic to go through nginx so we can use HAProxy to load balance servers. Will approach #2 work within nginx if I properly setup the proxy_set_header entries? I envision something along the lines of this within my final config file (using approach #2): server { listen Y.Y.Y.174:443; #Internally routed IP address server_name *.example.com; proxy_pass http://Y.Y.Y.174:8081; } server { listen Y.Y.Y.174:8081; server_name site1.example.com; -- NORMAL CONFIG ENTRIES -- proxy_pass http://IISServer01:8081; } server { listen Y.Y.Y.174:8081; server_name site2.example.com; -- NORMAL CONFIG ENTRIES -- proxy_pass http://IISServer01:8082; } server { listen Y.Y.Y.174:8081; server_name site3.example.com; -- NORMAL CONFIG ENTRIES -- proxy_pass http://IISServer02:8083; } This seems like a way, but I'm not sure if it's the best way. Am I missing a simpler approach to this?

    Read the article

< Previous Page | 47 48 49 50 51 52 53 54 55 56 57 58  | Next Page >