Search Results

Search found 1733 results on 70 pages for 'isc dhcp'.

Page 51/70 | < Previous Page | 47 48 49 50 51 52 53 54 55 56 57 58  | Next Page >

  • Add a server between router and switch (production)

    - by Kossel
    I have a small office network basically like below, there are more router/pc connected in S1. As you can see, the router is doing job of DHCP, DNS. but now I wish to add a Linux server between R1 and S1, So I can monitor the network traffic and do other more advance server admin stuff. the whole office network is 192.168.1.x and people are using their computer everyday. What network configuration should the new Linux server have (both interfaces) in order to minimize the changes need in the network? tried to change R1 ip to 192.168.100.1 them add the server with FE0/0 192.168.100.1 and FE0/1 192.168.1.1 but looks cannot ping the original Router..

    Read the article

  • Windows 7 ipv4 autoconfiguration - cannot connect to internet

    - by GuiccoPiano
    I get my internet connection from a guy (lets call him my service provider henceforth). He gives internet connections to many students here in my hostel. My PC gets a private IP through his DHCP server. Now, when I switch on my WiFi, my PC gets a private IP as it should and I can connect to the internet just fine. But now when I connect my LAN cable, my PC gets some "Autoconfiguration IPv4 address" 169.254.110.154(Preferred) and I cannot connect to the internet. Here is the ipconfig /all output for ethernet port: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Marvell Yukon 88E8059 PCI-E Gigabit Ethernet Controller Physical Address. . . . . . . . . : <<MAC DISPLAYED HERE>> DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::5054:a347:7d06:6e9a%11(Preferred) Autoconfiguration IPv4 Address. . : 169.254.110.154(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : DHCPv6 IAID . . . . . . . . . . . : 285222078 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-50-AC-68-54-42-49-EE-52-16 DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1 fec0:0:0:ffff::2%1 fec0:0:0:ffff::3%1 NetBIOS over Tcpip. . . . . . . . : Enabled I also tried: Start a command prompt as admin. Run "netsh winsock reset" Run "netsh interface ipv4 reset" Run "netsh interface ipv6 reset" Restart your computer. All this does not work. Any idea to solve the problem?

    Read the article

  • ubuntu server in a vm, can't connect to internet

    - by jessh
    I'm attemtping to host my own development web server in a virtual box guest, Ubuntu Server. I would like this virtual machine to be accessible from not only my home network, but outside the LAN as well. As such, I've set up a static IP (so I can later forward ports to this static IP.) My virtual box settings have this vm only using one adapter -- in bridged mode. Here's what my /etc/network/interfaces looks like: iface eth0 inet static address 10.0.1.203 /*this is outside the DHCP range*/ netmask 255.255.255.0 gateway 10.0.1.1 network 10.0.1.0 broadcast 10.0.1.255 dns-nameservers: 8.8.8.8 8.8.8.4 Here's what the output of ifconfig looks like: https://dl.dropbox.com/u/2241201/locker/ubuntu.png My Host is a mac mini, running OS X 10.7. From within the guest, if I ping google.com: $ ping google.com # outputs 'ping: unknown host google.com' immediately Why am I unable to access the web?

    Read the article

  • How can I make my Ubuntu server accessible to the internet ?

    - by wahid
    Hi, I already installed applications to make my server web server. when I type the DHCP released ip address in the web browser, i can access it but all it says is "it works....etc". I can copy files to /var/www successfuly using WINSCP but yet, i can not see any files when I connect to it using my windows machine in the browser. Secondly , I tried to forward port on my home SMC router, it only accepts local lan ip which my ubuntu server picks up internet ip from router...what should i do ? can you help please ???? Thanks,

    Read the article

  • How to show what proxies/firewalls are enabled on Windows XP?

    - by Stephen Melrose
    Hi, I'm trying to fix a Windows XP PC that is having a strange problem. The computer can't seem to connect to the internet, even though an internet connection is present. The router and internet is working fine as I've connected a laptop to it via LAN and wireless and both worked fine. The PC in question is connected to the router as it has an IP from the DHCP. The problem is I can't connect to nor ping any internet address from the PC. I can't even connect to the router admin itself. I've tried both LAN ports in the PC, same problem and both. I'm assuming there's a proxy or firewall on the PC stopping the connections, I just don't know how to find them or see which one is causing the issue. So my question is how do I on Windows XP display the system proxy settings and/or any firewalls that are running? Cheers.

    Read the article

  • Proccess of carrying out a BER Test

    - by data
    I am subscribed to an ISP supplying a 3meg ADSL line. Lately (for the last 4 weeks) speeds have dropped from the usual average downstream speed of ~250kbps to just 0.14Mbps (according to speedtest.net) and employees are complaining about lack of access to the server. I have been calling customer support and logging calls for the last 3 weeks, but they have been unable to determine the source of the problem other carrying out a few bitstream tests and checking the DHCP renewal times. I am going to call back and suggest carrying out a BER test. What type of equipment is needed to carry out this test? I have access to a wide range of Cisco networking equipment. Other: We dont need a leased line as there are less than ten employees.

    Read the article

  • HUGE MAC FILTER and scripting

    - by user195917
    I make an dhcp server on CentOS, and i apply a mac filter for my clients. Now, with a small number of clients (max 10) ,is not that hard, but what I will do with 2000 clients? My idea was to create a list (ex. "macfilter.lst") and this list, to be updated after a database. I have tow questions. First: How do i create a filter in IPTABLES that takes info`s from a file (file hosted on server) Second: Any idea about how to write a script, that update a file after a database?? Thanks so much for your help.

    Read the article

  • Routing connections to passthrough a local machine

    - by xiamx
    Please tell me if what I'm trying to do is feasible. I have a router named "R" which is connected to WAN. R allows adding rules to the routing table. There are numerous of machines connected to the LAN port of R, they all have ip addresses 192.168.1.* assigned with DHCP on R. Among those machines, there's a machine C with ip address 192.168.1.100. I want all traffic of other machines in the subnet to pass-through machine C where some filtering and logging will be done. Is this possible? Is there a name for what I'm trying to do? (so i can do more googling later)

    Read the article

  • How do I bridge a connection from Wi-Fi to TAP on Mac OS X? (for the emulator QEMU)

    - by penx
    I'm trying to setup a bridge between my Wi-Fi connection and an emulator (QEMU). I need a virtual machine to be on the same LAN as the host, with its own IP address. QEMU requires using a TAP (virtual network device) so I have installed tuntaposx, have it running, and can open up QEMU using a TAP: qemu-system-arm -kernel zImage.integrator -initrd arm_root.img -m 256 -net nic -net tap,ifname=tap1 -nographic -append "console=ttyAMA0" I have a script that configures the bridge once QEMU has opened up the TAP interface: sysctl -w net.link.ether.inet.proxyall=1 sysctl -w net.inet.ip.forwarding=1 sysctl -w net.inet.ip.fw.enable=1 ifconfig bridge0 create ifconfig bridge0 addm en1 ifconfig tap1 0.0.0.0 up ifconfig bridge0 addm tap1 ifconfig bridge0 up If I manually set an IP on the VM, I can ping from the VM to the host, but not from the host to the VM. Also, I can't access the rest of the network from the VM - including not being able to set an IP over DHCP. Any ideas?

    Read the article

  • Can't access internet even though everything is working

    - by entity64
    A friend recently upgraded to a new cable internet connection. The modem connects to the router and various PCs and smartphones from her roommates connect to the router. They don't have any problem accessing the internet. She has Windows 8 and can't access any website (via wifi and ethernet). DNS (UDP) is working, DHCP set up everything correctly, Wifi is working, Trace routes and Pings (ICMP) go through with no problem at all. But neither Dropbox nor Skype nor Spotify nor any browser (all TCP) can access any website. The thing is though, she can connect through the university wifi and via a neighbors wifi. It's just her home connection. No firewalls are running and the computer is clean - no malware. How could it be that only her home connection won't work and others do?

    Read the article

  • Get the MAC addresses of all the machines connected to a LAN when NO machines have got an IP address yet

    - by JtheRocker
    Here is the real scenario. I have say 4 machines not having any IP address yet connected to a switch. In one of the machines (OS=CentOS), I would install a DHCP server and would provide the other machines IP addresses. Prior to assigning them IP addresses, I need to get the MAC address of each of the machines that I would assign IP addresses to. So, my question here is how to I get the MAC addresses of all the machines connected to a switch when NO machine has got any IP address yet? It's mandatory for my use case that I won't be having any IP addresses before the MAC addresses. -Thanks

    Read the article

  • My Laptop (HP/Compaq 2510p) running ubuntu 10.04 LTS keeps losing the WLAN connection.

    - by Ernelli
    I am using Wicd and can successfully connect to my ADSL router (Thomson TG 787) using WPA PSK. But with regular interval I lose the ability to connect to Internet. I can ping the GW and can actually ping servers on the Internet but not connect to them using HTTP (Tested with both Firefox and wget). I would suspect the router unless for the fact that the problem does not show up when running Windows XP on the same computer and also, when the problem arises, a simple disconnect/connect in Wicd solves the problem, which does not involve the router (Except for the DHCP request). I have searched Ubuntu forums without luck, most problems described relate to specific network drivers or other problems. Does anyone have the same experience with Linux/Ubuntu and WLAN?

    Read the article

  • Does my DLink DNS-323 need to reside on a "192.168.0.0/24" subnet?

    - by Raymond
    I've installed two brand new 2-tib drives in the DLink and plugged it in to my network. I set my router's static address table to include the MAC address of the device; however it doesn't ever "show up." Do I need to use the custom software to administer this device? Do I need to use a "192.168.0.0/24" network in order for this device to work (asking because it states that if DHCP isn't detected, it will default to an address in that range; and my network is not in that range).

    Read the article

  • Is there a Linux kernel boot parameter to configure an IPv6 address?

    - by aef
    I know there is a parameter named ip which lets you configure IPv4 addresses on the Linux kernel through the boot loader. That looks like the following: ip=192.0.2.1::192.0.2.62:255.255.255.192::eth0:none I'm looking for an equal parameter for IPv6 configuration. I couldn't find anything about this in the kernel documentations. Update: Because of a lot of you asked why I would need this: The idea to use a kernel configuration came up related to this problem. I suspect the regular boot-up interface configuration is not done, because the interfaces are already up. The reason for this could be that I'm using a pre-boot environment with a Dropbear SSH server to allow me to unlock my encrypted root partition. The IP addresses for this environment are configured through GRUB with the ip= parameter. There is no DHCP or Router Advertisement available on that Ethernet segment and as this is the uplink segment provided by a large hosting company, there is no way to change that fact.

    Read the article

  • Dns works, can ping, but cannot load web pages in browser

    - by user1224595
    Yesterday I changed routers, and my desktop computer started acting up. I could ping websites, and nslookup was able to resolve names to addresses, but neither chrome, firefox, nor ie could load any webpages. None of my other computers connected to the same wireless router have any problems. I connect my desktop to the router through a cheap wifi dongle. I did a wireshark capture of the browser request, and I have uploaded the pcap here. https://drive.google.com/file/d/0B7AsPdhWc-SwbTV0bUJLQXo4UUE/edit?usp=sharing One strange thing I noticed was the spamming of ssdp packets. I am not super familiar with networking, but it seems that it is not a problem with the router, as dns works, and so does dhcp (the desktop is assigned an address correctly). Any help would be appreciated.

    Read the article

  • Windows 7 - ICS - Xbox360

    - by Hailwood
    I am trying to connect my xbox360 to the internet through ICS using my laptop. I have done this a few days ago using the exact same hardware(so no hardware problems) The laptop can browse the internet. The laptop gets its settings though DHCP. I have enabled ICS on the Wireless connection (where the internet is coming from) I have set the xbox and the Wired connection on the laptop to obtain settings automatically. The issue is that the Wired connection only shows 'Unidentified Network'. What could i be doing wrong?

    Read the article

  • DNS point to server on ISP and keep shared host too?

    - by Dwayne
    I know this is probably quite easy to do, but I might just have the right search sorted out... so here is the situation: We have example.com set up as a hosted server along with app1.example.com, app2.example.com and a few others. What I would like to do is set up the right zone file to also make our internal server addressable from the outside world as internalapp.example.com. This server sits behind a firewall (pfsense) and is hooked up to the world via a cable modem that is technically on DHCP from our ISP, but has had the same external IP for the past 15 months so far. What would be the best way to set this up?

    Read the article

  • DNS record reappears after having been deleted

    - by palmbardier
    I've got a Microsoft Windows Server 2003 R2 acting as a domain controller for a small network. It provides DHCP and DNS among a few other services. It's only got a single NIC, but it's configured with two IP addresses. I want it's name to resolve to one of the two IP addresses assigned to its NIC. I've unchecked "Register this connection's addresses in DNS" under the "Advanced TCP/IP Settings". Currently we've got two distinct DNS Host (A) records for this domain controller: dc-001 - 10.0.0.1 dc-001 - 10.0.100.1 I've deleted the first entry but it continues to reappear in my dnsmgmt snap-in. Unfortunately I'm not a Microsoft systems administrator by trade. Does anyone familiar with Microsoft server environments know why a deleted Host (A) record would reappear? Is there another check-box I need to toggle? Thanks in advance to all of you Microsoft experts out there.

    Read the article

  • Ping reply not getting to LAN machines but getting in Linux router Gateway

    - by Kevin Parker
    I have configured Ubuntu 12.04 as Gateway machine.its having two interfaces eth0 with ip 192.168.122.39(Static) and eth1 connected to modem with ip address 192.168.2.3(through DHCP). ip-forwarding is enabled in router box. Client machine is configured as: ip address 192.168.122.5 and gateway 192.168.122.39 Client machines can ping router box(192.168.122.39).but when pinged 8.8.8.8 reply is not reaching Client machines but in the tcpdump output on gateway i can see echo request for 8.8.8.8 but never echo reply.Is this because of 122.5 not forwarding request to 2.0 network.Can u please help me in fixing this.

    Read the article

  • Sharing VPN access between two computers on the LAN

    - by Axelle Ziegler
    I have VPN access to several machines in my office from my home machine. I'd like to be able to access those machines from another computer on my LAN, without setuping a second VPN access. Both computers are Windows 7 machines. Is there a way for my "main" computer to share its VPN access to another machine on the LAN? How would one setup this share? I don't think "simple" Internet connection sharing fits my needs because: My LAN already has its own DHCP/Router to access the Internet, and I'd like to keep it this way I can't access the Internet through my VPN connection

    Read the article

  • Server 2012 file server security - File access through software only?

    - by user1607914
    I have just setup a server 2012 essentials R2 box as a test bed for my small business. Its running Essentials R2 as a VM on a Essentials R2 host. I have set it up to be the DC and DHCP server and joined a client. My next task is to use it as a file server but I am not quite sure how to set it up. All the client interactions with the file server will be through client side software. I therefore do not want any access to the files apart from through the software. I have looked at the ntfs permissions and there is a permission called "List Folder/Read Data" however I am unsure this will do what I want. Is it possible to give access to the files but not allow access through the windows explorer / command line?

    Read the article

  • Need to access Mac via ssh remotely through another Mac with Internet Sharing

    - by Ze'ev
    My setup at office is: Internet - AirportExtreme --(wifi)-- AirportExpress --(eth)-- MacPro1 --(eth)-- MacPro2 I want to be able to access MacPro2 from laptop at home via ssh (and sftp). Is it possible? The AirportExtreme is set to "DHCP and NAT" and is doling out 10.0.1.xxx IPs. The AirportExpress is 10.0.1.2. MacPro1 is 10.0.1.3 via Ethernet to AirportExpress. It is then connected by 2nd Ethernet port (192.168.2.1) to MacPro2, which is 192.168.2.2. Is there any way to "tunnel through" to MacPro2 from home? Thanks!

    Read the article

  • Networking issues with WNR3500L

    - by ageis23
    When I try connecting to my wireless network it attempts to connect then gives up. There's something strange going on with the mac's. The eternet switch and all the vlan interfaces have a mac 00:FF:FF:FF:FF:FF. config 'switch' 'eth0' option 'vlan0' '2 3 4 8*' option 'vlan1' '0 8' option 'vlan2' '1 8' config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'lan' option 'type' 'bridge' option 'ifname' 'eth0.1' option 'proto' 'static' option 'netmask' '255.255.255.0' option 'ipaddr' '192.168.2.1' option 'ip6addr' '' option 'gateway' '192.168.1.253' option 'ip6gw' '' option 'dns' '' config 'interface' 'wan' option 'ifname' 'eth0' option 'proto' 'dhcp' option 'ipaddr' '192.168.1.8' option 'ip6addr' '' option 'netmask' '255.255.255.0' option 'gateway' '192.168.1.253' option 'ip6gw' '' option 'dns' '192.168.1.253' config 'interface' 'dmz' option 'ifname' 'eth0.2' option 'proto' 'static' option 'ipaddr' '192.168.0.1' option 'netmask' '255.255.255.0' Any help on this will be greatly appreciated! When I try setting the mac using macaddr it does nothing. It works perfectly fine when I turn the authentication off.

    Read the article

  • Internet sharing over LAN on Windows Server 2012

    - by USER
    I have a DSL modem connected to a server (ON NIC1) running Windows Server 2012 and 7 computers (running Windows 7 32-Bit) connected to a server though a network switch (ON NIC2). I shared the internet connection from the server through DHCP so I am able to access the internet from those 7 computers, but I am unable to: Access Google.com Activate Windows Update Windows An error is arising that says UNABLE TO ACTIVATE WINDOWS Activation Error Code: 0x80072EE2 Firewall and Anti-Virus are off on both the Server and the Clients. Is there is any additional setting that I want to do?

    Read the article

  • Why does my ethernet connection keep re-connecting, only with Windows?

    - by Nick Bolton
    I'm using Windows 7, and I have several computers on my network. For some reason, the network connection keeps disconnecting and immediately re-connecting. Infact, it may just be refreshing the DHCP lease... but I'm not sure. I've tried changing the network card, and ethernet cable, but the issue is still happening. I can only imagine that the issue is with the ethernet switch, but this doesn't happen on my other desktop which uses the same ethernet switch. Any ideas?

    Read the article

< Previous Page | 47 48 49 50 51 52 53 54 55 56 57 58  | Next Page >