Search Results

Search found 1456 results on 59 pages for 'wall'.

Page 51/59 | < Previous Page | 47 48 49 50 51 52 53 54 55 56 57 58  | Next Page >

  • Determining the health of a Cisco switch port?

    - by ewwhite
    I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced recently, however, the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link. We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

    Read the article

  • Understading the output of syslogd -d

    - by Heoa
    What is the meanding of 80, F and X in the following output of syslogd -d? 0: X X X X FF X X X X X FF X X X X X X X X X X X X X X FILE: /var/log/auth.log (unused) 1: FF FF FF FF X FF FF FF FF FF X FF FF FF FF FF FF FF FF FF FF FF FF FF FF FILE: /var/log/syslog (unused) 2: X X X FF X X X X X X X X X X X X X X X X X X X X X FILE: /var/log/daemon.log (unused) 3: FF X X X X X X X X X X X X X X X X X X X X X X X X FILE: /var/log/kern.log (unused) 4: X X X X X X FF X X X X X X X X X X X X X X X X X X FILE: /var/log/lpr.log (unused) 5: X X FF X X X X X X X X X X X X X X X X X X X X X X FILE: /var/log/mail.log (unused) 6: X FF X X X X X X X X X X X X X X X X X X X X X X X FILE: /var/log/user.log (unused) 7: X X 7F X X X X X X X X X X X X X X X X X X X X X X FILE: /var/log/mail.info (unused) 8: X X 1F X X X X X X X X X X X X X X X X X X X X X X FILE: /var/log/mail.warn (unused) 9: X X F X X X X X X X X X X X X X X X X X X X X X X FILE: /var/log/mail.err (unused) 10: X X X X X X X 7 X X X X X X X X X X X X X X X X X FILE: /var/log/news/news.crit (unused) 11: X X X X X X X F X X X X X X X X X X X X X X X X X FILE: /var/log/news/news.err (unused) 12: X X X X X X X 3F X X X X X X X X X X X X X X X X X FILE: /var/log/news/news.notice (unused) 13: 80 80 X 80 X 80 80 X 80 80 X 80 80 80 80 80 80 80 80 80 80 80 80 80 80 FILE: /var/log/debug (unused) 14: 70 70 X X X 70 70 X 70 X X 70 70 70 70 70 70 70 70 70 70 70 70 70 70 FILE: /var/log/messages (unused) 15: 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 WALL: 16: F0 F0 FF FF F0 F0 F0 FF F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 PIPE: |/dev/xconsole (unused)

    Read the article

  • Error installing scipy on Mountain Lion with Xcode 4.5.1

    - by Xster
    Environment: Mountain Lion 10.8.2, Xcode 4.5.1 command line tools, Python 2.7.3, virtualenv 1.8.2 and numpy 1.6.2 When installing scipy with pip install -e "git+https://github.com/scipy/scipy#egg=scipy-dev" on a fresh virtualenv. llvm-gcc: scipy/sparse/linalg/eigen/arpack/ARPACK/FWRAPPERS/veclib_cabi_c.c In file included from /System/Library/Frameworks/vecLib.framework/Headers/vecLib.h:43, from /System/Library/Frameworks/Accelerate.framework/Headers/Accelerate.h:20, from scipy/sparse/linalg/eigen/arpack/ARPACK/FWRAPPERS/veclib_cabi_c.c:2: /System/Library/Frameworks/vecLib.framework/Headers/vfp.h:51:23: error: immintrin.h: No such file or directory In file included from /System/Library/Frameworks/vecLib.framework/Headers/vecLib.h:43, from /System/Library/Frameworks/Accelerate.framework/Headers/Accelerate.h:20, from scipy/sparse/linalg/eigen/arpack/ARPACK/FWRAPPERS/veclib_cabi_c.c:2: /System/Library/Frameworks/vecLib.framework/Headers/vfp.h: In function ‘vceilf’: /System/Library/Frameworks/vecLib.framework/Headers/vfp.h:53: error: incompatible types in return /System/Library/Frameworks/vecLib.framework/Headers/vfp.h: In function ‘vfloorf’: /System/Library/Frameworks/vecLib.framework/Headers/vfp.h:54: error: incompatible types in return /System/Library/Frameworks/vecLib.framework/Headers/vfp.h: In function ‘vintf’: /System/Library/Frameworks/vecLib.framework/Headers/vfp.h:55: error: ‘_MM_FROUND_TRUNC’ undeclared (first use in this function) /System/Library/Frameworks/vecLib.framework/Headers/vfp.h:55: error: (Each undeclared identifier is reported only once /System/Library/Frameworks/vecLib.framework/Headers/vfp.h:55: error: for each function it appears in.) /System/Library/Frameworks/vecLib.framework/Headers/vfp.h:55: error: incompatible types in return /System/Library/Frameworks/vecLib.framework/Headers/vfp.h: In function ‘vnintf’: /System/Library/Frameworks/vecLib.framework/Headers/vfp.h:56: error: ‘_MM_FROUND_NINT’ undeclared (first use in this function) /System/Library/Frameworks/vecLib.framework/Headers/vfp.h:56: error: incompatible types in return In file included from /System/Library/Frameworks/vecLib.framework/Headers/vecLib.h:43, from /System/Library/Frameworks/Accelerate.framework/Headers/Accelerate.h:20, from scipy/sparse/linalg/eigen/arpack/ARPACK/FWRAPPERS/veclib_cabi_c.c:2: /System/Library/Frameworks/vecLib.framework/Headers/vfp.h:51:23: error: immintrin.h: No such file or directory In file included from /System/Library/Frameworks/vecLib.framework/Headers/vecLib.h:43, from /System/Library/Frameworks/Accelerate.framework/Headers/Accelerate.h:20, from scipy/sparse/linalg/eigen/arpack/ARPACK/FWRAPPERS/veclib_cabi_c.c:2: /System/Library/Frameworks/vecLib.framework/Headers/vfp.h: In function ‘vceilf’: /System/Library/Frameworks/vecLib.framework/Headers/vfp.h:53: error: incompatible types in return /System/Library/Frameworks/vecLib.framework/Headers/vfp.h: In function ‘vfloorf’: /System/Library/Frameworks/vecLib.framework/Headers/vfp.h:54: error: incompatible types in return /System/Library/Frameworks/vecLib.framework/Headers/vfp.h: In function ‘vintf’: /System/Library/Frameworks/vecLib.framework/Headers/vfp.h:55: error: ‘_MM_FROUND_TRUNC’ undeclared (first use in this function) /System/Library/Frameworks/vecLib.framework/Headers/vfp.h:55: error: (Each undeclared identifier is reported only once /System/Library/Frameworks/vecLib.framework/Headers/vfp.h:55: error: for each function it appears in.) /System/Library/Frameworks/vecLib.framework/Headers/vfp.h:55: error: incompatible types in return /System/Library/Frameworks/vecLib.framework/Headers/vfp.h: In function ‘vnintf’: /System/Library/Frameworks/vecLib.framework/Headers/vfp.h:56: error: ‘_MM_FROUND_NINT’ undeclared (first use in this function) /System/Library/Frameworks/vecLib.framework/Headers/vfp.h:56: error: incompatible types in return error: Command "/usr/bin/llvm-gcc -fno-strict-aliasing -Os -w -pipe -march=core2 -msse4 -fwrapv -DNDEBUG -g -fwrapv -O3 -Wall -Wstrict-prototypes -Iscipy/sparse/linalg/eigen/arpack/ARPACK/SRC -I/Users/xiao/.virtualenv/lib/python2.7/site-packages/numpy/core/include -c scipy/sparse/linalg/eigen/arpack/ARPACK/FWRAPPERS/veclib_cabi_c.c -o build/temp.macosx-10.4-x86_64-2.7/scipy/sparse/linalg/eigen/arpack/ARPACK/FWRAPPERS/veclib_cabi_c.o" failed with exit status 1 Is it supposed to be looking for headers from my system frameworks? Is the development version of scipy no longer good for the latest version of Mountain Lion/Xcode?

    Read the article

  • Cannot install passenger with Nginx

    - by Luc
    Hello, I have a rack application that I want to migrate from Ruby 1.8.7 + Apache + passenger to Ruby 1.9.1 + Nginx + passenger. I have made up the following script for a quick install all in one, and it raises an error... Here is the installation script: (basic one with all the steps I need to install everything on a Ubuntu 10.04 Lucid Lynx fresh box) Nginx sources cd /tmp wget http://nginx.org/download/nginx-0.7.66.tar.gz tar xzf nginx-0.7.66.tar.gz cd nginx-0.7.66 openssl required for SSL/TLS sudo apt-get install openssl sudo apt-get install libssl-dev Compilation stuff sudo apt-get zlib1g-dev Ruby interpreter 1.9.1 sudo apt-get install ruby1.9.1 ruby1.9.1-dev rubygems1.9.1 irb1.9.1 ri1.9.1 rdoc1.9.1 build-essential nginx libopenssl-ruby1.9.1 Make sure default ruby uses version 1.9.1 sudo update-alternatives --install /usr/bin/ruby ruby /usr/bin/ruby1.9.1 400 --slave /usr/share/man/man1/ruby.1.gz ruby.1.gz /usr/share/man/man1/ruby1.9.1.1.gz --slave /usr/bin/ri ri /usr/bin/ri1.9.1 --slave /usr/bin/irb irb /usr/bin/irb1.9.1 --slave /usr/bin/rdoc rdoc /usr/bin/rdoc1.9.1 sudo update-alternatives --config ruby Passenger (rake-0.8.7, fastthread-1.0.7, rack-1.1.0, passenger-2.2.14) sudo gem install passenger Activate Passenger in nginx, select option 2 to use nginx sources donwloaded above cd /var/lib/gems/1.9.1/gems/passenger-2.2.14/bin sudo ./passenger-install-nginx-module And this is the error message I got: /var/lib/gems/1.9.1/gems/passenger-2.2.14/ext/nginx/ContentHandler.c gcc -c -pipe -O -W -Wall -Wpointer-arith -Wno-unused-parameter -Wunused-function -Wunused-variable -Wunused-value -Werror -g -I src/core -I src/event -I src/event/modules -I src/os/unix -I /tmp/pcre-8.00 -I objs -I src/http -I src/http/modules -I src/mail \ -o objs/addon/nginx/StaticContentHandler.o \ /var/lib/gems/1.9.1/gems/passenger-2.2.14/ext/nginx/StaticContentHandler.c /var/lib/gems/1.9.1/gems/passenger-2.2.14/ext/nginx/StaticContentHandler.c: In function ‘passenger_static_content_handler’: /var/lib/gems/1.9.1/gems/passenger-2.2.14/ext/nginx/StaticContentHandler.c:71: error: ‘ngx_http_request_t’ has no member named ‘zero_in_uri’ make[1]: *** [objs/addon/nginx/StaticContentHandler.o] Error 1 make[1]: Leaving directory `/tmp/nginx-0.7.66' make: *** [build] Error 2 -------------------------------------------- It looks like something went wrong Please read our Users guide for troubleshooting tips: /var/lib/gems/1.9.1/gems/passenger-2.2.14/doc/Users guide Nginx.html I do not understand the reason of this error. Is this a compatibility problem ? Hope you have any clues :) Thanks a lot, Luc

    Read the article

  • D-Link DIR-300 slows down / loses network

    - by basic6
    Hi there, there are 2 buildings (A and B). In bldg A is an open WLAN (which I'm allowed to use btw). In bldg B is a computer that I want to connect to that network. So I flashed an old D-Link DIR-300 AP with DD-WRT, mounted it to the wall (bldg B) near a window, attached a 13 dBi directional antenna (pointing to bldg A) and configured it as AP client in that wireless network. Then there's another AP, connected to the D-Link AP, acting as standard access point, which the computer is connected to. That's basically working so far, but: Every now and then the connection is lost. Not the connection between the computer and the D-Link (I can access the DD-WRT admin page normally) or the connection between the D-Link and the WLAN (in Status - Wireless it says it's still connected to the network), but when I want to access a web page (which only works if I'm connected to the wireless network from bldg A), my Firefox keeps "Looking for" (name resolution) without finding anything. When I reset the D-Link (power off, power on) in this situation, after some moments, everything's working fine again (Internet access). I've no idea why this is happening, but usually it's at most every few weeks (most times when nobody was using the computer, so no traffic). Compared to the connection speed when I connect directly to the WLAN in bldg A (Laptop), the speed in bldg B is rather slow, but I have the impression that this difference is worse in the last few days. A few minutes ago, I got 582 KB/s down and 911 KB/s up in bldg A (directly/laptop) and 84 KB/s down and 9 KB/s up in bldg B. The speed in bldg B used to be way higher (I remember 200 KB/s up) while the actual network speed in bldg A was lower than it is now (close to those 200). I'm aware that the wireless connection between those buildings should slow things down, but I'm wondering why this difference has become that extreme. Thanks for any tips... Update: I currently want to upload a large file (1.5 GB) via FTP (FileZilla). Since that caused the D-Link to disconnect (as described in first post), I took my laptop to bldg A, connected directly to the original WLAN (bypassing my D-Link) and tried the same upload. Guess what - same issue: At some point the connection is dead (at this point I would have reset my D-Link if I was connected to it). Just as the D-Link, my laptop is still connected, but not even name resolution is working ("Looking for..." in Firefox). After reconnecting, it's working again. Maybe my D-Link isn't the problem at all...

    Read the article

  • WinXP - Having trouble sharing internet with 3G USB modem via ICS

    - by Carlos Nunez
    all! I've been banging my head against a wall with this issue for a few days now and am hoping someone can help out. I recently signed up for T-Mobile's webConnect 3G/4G service to replace the faltering (and slow) DSL connection in my apartment. The goal was to put the SIM in one of my old phones and use its built-in WLAN tethering feature to share Internet out to rest of my computers. I quickly found out that webConnect-provisioned SIMs do not work with regular smartphones, so I was forced to either buy a 4G-compatible router or tether one of my old laptops to my wireless router and share out that way. I chose the latter, and it's sharpening my inner masochistic self by the day. Here's the setup: GSM USB modem (via hub), ICS host - 10/100 Mbps Ethernet NIC, ICS "guest" - WAN port of my SMC WGBR14N wireless router in bridged mode (i.e. wireless access point). Ideally, this would make my laptop the DHCP server and internet gateway with the WAP giving everyone wireless coverage. I can browse internet on the host laptop fine. However, when clients try to connect, they get a DHCP-assigned IP from the laptop and are able to use the Internet for a few minutes before completely dying. After that happens, they are able to re-associate with the WAP and get IP addresses, but are unable to use Internet or resolve IP addresses until the laptop and router are restarted. If they do get access, it's very, very slow. After running Wireshark on the host machine, it turns out that this is because every TCP connection keeps getting RST. DNS seems to work. I would normally think the firewall is the culprit here, but when it drops packets, it drops them completely. The fact that TCP connections are being ACK'ed by the destination rules that out. Of course, none of the event Log isn't saying anything about what's going on. I also tried disabling power management on the NIC, since that's caused problems in the past; that didn't help either. I finally disabled receive-side scaling as per a Microsoft KB (that applied to Windows Server 2003, SP2) to no avail. I'm thinking of trying it with a different NIC (will be tough; don't have a spare Ethernet NIC around for the laptop), but I'm getting the impression that this simply doesn't work. Can anyone please advise? I apologise for the length of this post; all contributions are much appreciated! -Carlos.

    Read the article

  • Win 8: Adding a boot volume to an MBR dynamic disk [NOT about changing to basic disks]

    - by Stilez
    (This is NOT aiming to convert to basic disk. In this question, the disk stays dynamic but becomes bootable) There doesn't seem to be a clear, well stated answer I can find, for the question "What are the criteria for Windows 8 to successfully boot from an MBR dynamic disk", or "how do I fix a dynamic MBR partition that's failing boot"? I've tried to educate myself but can't find crucial information to clear it all up. My existing HDD/SSD setup: DISK 0 ~ 60GB SSD/MBR/basic: (350MB recovery)(60GB windows 8 bootable) DISK 1 ~ 512GB SSD/MBR/dynamic: (350MB recovery)(60GB unallocated)(410GB mirrored data) DISK 2 ~ 512GB SSD/MBR/dynamic: (350MB recovery)(60GB unallocated)(410GB mirrored data) DISKS 3, 4, 5: (ignored for simplicity: 2xHDD RAID1 + caching SSD) I'm heavy duty on data crunching and virtualisation, just maxxed out 32GB RAM @ 2133 and moved to 4960X + 64GB. Disk 0 is a pure system disk of little value, and virtualisations runs off mirrored SSDs (Samsung 840 Pro 512 x 2) for double speed reading and so they snapshot in reasonable time. I'm using 4 SATA3 ports and the board only has two decent Intel ports (onboard Marvell are poorer quality). I'm wary of choosing between LSI, HighPoint and other 3rd party controllers as I'm unfamiliar with the maze of decent RAID cards (that's a whole other issue!). I want to cut down my SSD needs by moving the boot volume and caching volume to the 840 pros, giving a setup with 2 fewer SSDs: DISK 0 ~ 512GB SSD/MBR/dynamic: (350MB recovery)(60GB boot)(410GB mirrored data) DISK 1 ~ 512GB SSD/MBR/dynamic: (350MB recovery)(30GB cache for the ICH10R mirror)(30GB temp)(410GB mirrored data) DISKS 2, 3: (2xHDD RAID1) Intel's RST allows this, Win 8 allows booting off a MBR/dynamic disk, and the two 60GB SSDs are hardly the fastest SSDs anyway, they'll get repurposed. Moving the caching volume is easy. Moving the boot volume has me stumped. The difficulty is, I'm hitting a wall of knowledge here. I have a UEFI Asus motherboard with an previous traditional MBR/basic boot disk, and I want it to boot from a disk and volume that's MBR/dynamic. The disk copy is physically ok (Partition Wizard Server will copy to dynamic volumes) but then hits a light blue 0xc000000e boot error. No real surprise, I expected to have some boot fixing, but had expected Windows to boot-fix it (all drivers exist), or the usual manual fixes to work. Specifically, I don't know enough, to know what's got to be manually checked and perhaps corrected for the disk to boot (legacy/uefi/bios, odd partitions, boot tables, disk IDs, hidden boot files, oh my!), or if I need to change any of this secure boot/UEFI/legacy stuff in the bios, convert a 512 SSD to basic and then back to dynamic when working, or if the issue is pure OS config using "diskpart", "bootsect" and "bootrec" from the Win8 DVD. The old system disk still boots but I don't know enough to figure what to fix, to make the system boot as I want. The answers probably aren't hard but the real issue is my confusion and missing information. Thanks for helping!

    Read the article

  • Effecient organization of spare cables and hardware

    - by Jake Wharton
    As many of you also likely do, I have a growing collection of cables, hardware, and spare parts (screws, connectors, etc.). I'm looking to find a good system of organization so that everything isn't a tangled mess, mismatched, and potentially able to be damaged. Since the the three things listed above are all have varying sizes and degrees of delicacy this poises an interesting problem. Presently I have those cheap plastic storage bins you find at Wal-mart for everything. Cables that were once wrapped neatly have become tangled due to numerous "I know I have a cable for this" moments. Hardware is mixed in other bins with odds and ends with no protection from each other. NICs, CPUs, and HDDs are all interacting and likely causing damage. Finally there are stray parts sprinkled amongst these two both in plastic bags and loose. I'm looking to unify this storage into a controlled chaos. Here are my thoughts: Odds and ends are the easiest. Screws, connectors, and small electronic parts lend themselves perfectly to tackle boxes and jewelry boxes. Since these are usually dynamically compartmentalized I can adjust for the contents and label them on the outside or inside of the lid. Cables are easily wrangled with short velcro strips but that doesn't stop them from being all mixed in together. Hardware is the worst offender. Size, shape, and degree of delicacy changes with nearly every piece. I'm willing to sacrifice a bit of organization for a somewhat efficient manner. What are all your thoughts? What is the best type of tackle or jewelry box to use? Most of them are cheap and flimsy. Is there a better alternative? How can I organize cables to know exactly (within reason) where one is? What about associating cables with hardware (Wall adapter to router, etc.)? What kind of storage unit lends itself to all shapes of hardware? Do I need to separate by size or degree of delicacy for better organization?

    Read the article

  • Is it possible to configure a CDN so that it will step out of the way for a subset of regional IPs?

    - by rwired
    We have a website which targets customers in China, both expat and local Chinese. We have an ICP license which allows us to host in a datacenter inside China. Internet in China is actually as fast as anywhere else (faster than most places actually), so long as the content is served-up within the boundaries of the Great-Firewall. Anything that crosses the wall is horribly slow. The problem is that most expats have some sort of VPN installed so that they can access all the blocked stuff. What this means is that when they access our site, the traffic first has to go out of China through the firewall to their VPN, and then back in. The performance is terrible, worse than if we were just hosting outside of China directly (which we used to do before the ICP was issued). So I want to use a global CDN to mirror the site automatically, but I only want to deliver the content via the CDN if the user's request IP address is outside of China. Inside China I would like the content to be served by our own server. I also want to be careful with the domain names. We currently use www.xxx.com and www.xxx.cn for language selection purposes, as these perform well in SEO on Google (which the expats use), and Baidu (which the locals use). If possible I would like to avoid having one domain on the outside, and the other on the inside since not all expats use a VPN, and some Chinese speakers also use VPNs. Also some of our legitimate customers in both languages are from outside of China. I also don't want to resort to using something like www2.xxx.com/cn for the outside connection if at all possible, since I have worries about duplicate content and canonical URLs ruining our SEO (unless you know of a quick fix for that). CDNs I'm considering are: Google PageSpeed, CloudFlare, Amazon CloudFront. None of which have datacenters inside China. I have complete control of the .com DNS zone records, but the .cn zones are under the control of the domain issuing body in China. I'm not sure at this time if they would allow even a CNAME to point to an IP outside of China (although I don't see why not). They no longer allow outside registrars like they used to.

    Read the article

  • Passenger 2.2.4, nginx 0.7.61 and SSL

    - by boompa
    Has anyone had any luck configuring Passenger and nginx with SSL? I've spent hours trying to get this configuration working as I'd like, using what few resources there are out there on the net, and I can't get any of the supposedly forwarded headers to show up in the Rails controller. For example, with a conf file of the following (and multiple variations thereof): server { listen 3000; server_name .example.com; root /Users/website/public; passenger_enabled on; rails_env development; } server { listen 3443; root /Users/website/public; rails_env development; passenger_enabled on; ssl on; #ssl_verify_client on; ssl_certificate /Users/website/ssl/server.crt; ssl_certificate_key /Users/website/ssl/server.key; #ssl_client_certificate /Users/website/ssl/CA.crt; ssl_session_timeout 5m; ssl_protocols SSLv3 TLSv1; ssl_ciphers ALL:!ADH:RC4+RSA:+HIGH:+MEDIUM:-LOW:-SSLv2:-EXP; proxy_set_header Host $http_host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X_FORWARDED_PROTO https; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; #proxy_set_header X-SSL-Subject $ssl_client_s_dn; #proxy_set_header X-SSL-Issuer $ssl_client_i_dn; proxy_redirect off; proxy_max_temp_file_size 0; } and Rails code in the controller like this: request.headers.each { |k, v| RAILS_DEFAULT_LOGGER.error "Header #{k} Val #{v}" } other headers appear, but not those set in nginx, e.g.: Header rack.multithread Val false Header REQUEST_URI Val /login/new Header REMOTE_PORT Val 64021 Header rack.multiprocess Val true Header PASSENGER_USE_GLOBAL_QUEUE Val false Header PASSENGER_APP_TYPE Val rails Header SCGI Val 1 Header SERVER_PORT Val 3443 Header HTTP_ACCEPT_CHARSET Val ISO-8859-1,utf-8;q=0.7,*;q=0.7 Header rack.request.query_hash Val Header DOCUMENT_ROOT Val /Users/website/public I've even gone so far as to modify Passenger's abstract_request_handler's main_loop method, i.e., headers, input = parse_request(client) if headers if headers[REQUEST_METHOD] == PING process_ping(headers, input, client) else headers.each { |h,v| log.unknown "abstract_request_handler: #{h} = #{v}" } process_request(headers, input, client) end end only to find that the supposedly added headers do not exist there either: abstract_request_handler: HTTP_KEEP_ALIVE = 300 abstract_request_handler: HTTP_USER_AGENT = Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10.5; en-US; rv:1.9.1) Gecko/20090624 Firefox/3.5 abstract_request_handler: PASSENGER_SPAWN_METHOD = smart-lv2 abstract_request_handler: CONTENT_LENGTH = 0 abstract_request_handler: HTTP_IF_NONE_MATCH = "b6e8b9afbc1110ee3bf0c87e119252ad" abstract_request_handler: HTTP_ACCEPT_LANGUAGE = en-us,en;q=0.5 abstract_request_handler: SERVER_PROTOCOL = HTTP/1.1 abstract_request_handler: HTTPS = on abstract_request_handler: REMOTE_ADDR = 127.0.0.1 abstract_request_handler: SERVER_SOFTWARE = nginx/0.7.61 abstract_request_handler: SERVER_ADDR = 127.0.0.1 abstract_request_handler: SCRIPT_NAME = abstract_request_handler: PASSENGER_ENVIRONMENT = development abstract_request_handler: REMOTE_PORT = 64021 abstract_request_handler: REQUEST_URI = /login/new abstract_request_handler: HTTP_ACCEPT_CHARSET = ISO-8859-1,utf-8;q=0.7,*;q=0.7 abstract_request_handler: SERVER_PORT = 3443 abstract_request_handler: SCGI = 1 abstract_request_handler: PASSENGER_APP_TYPE = rails abstract_request_handler: PASSENGER_USE_GLOBAL_QUEUE = false I'm tired of banging my head against the wall, so I'd truly appreciate any help I can get!

    Read the article

  • Legacy VB6 application under Win7 SQL error

    - by Shial
    We have a rather unfortunate legacy application at work, written originally in VB6 it predates anybody in our IT department by at least 5 years. We have a contracted developer for ongoing maintenance and where he can he rewrites sections over into .NET code (Not sure about his techniques here, this is a side job for his regular work as an IBM engineer) the application works fine (such as it is) under windows XP. We have only a couple of Windows 7 machines mainly for testing and this application seems to run into a wall. Things like the background not loading and SQL errors. This is even running under administrator. Running an SQL trace from the ODBC control panel shows several interesting things. It makes a connection to the database successfully initially where it runs a query to determine if it is running the correct version. This query works fine. 558-1af0 ENTER SQLExecDirectW HSTMT 0x020D7548 WCHAR * 0x04C8F0F0 [ 115] "SELECT count(*) c FROM tblSoftwareVersion WHERE fldSoftwareVersion = '123456' AND fldSoftwareName = 'Application.VB'" SDWORD 115 BMS 558-1af0 EXIT SQLExecDirectW with return code 1 (SQL_SUCCESS_WITH_INFO) HSTMT 0x020D7548 WCHAR * 0x04C8F0F0 [ 115] "SELECT count(*) c FROM tblSoftwareVersion WHERE fldSoftwareVersion = '123456' AND fldSoftwareName = 'Application.VB'" SDWORD 115 It then seems to drop its connection and can't find the ODBC connection despite the fact its connecting to the same DB. From the trace it looks like it configures the connection then it starts firing off SQLFreeStmt to unbind and close out then when in the application and it tries to do its thing there is no connection. 558-1af0 ENTER SQLFreeStmt HSTMT 0x020D7548 UWORD 2 <SQL_UNBIND> BMS 558-1af0 EXIT SQLFreeStmt with return code 0 (SQL_SUCCESS) HSTMT 0x020D7548 UWORD 2 <SQL_UNBIND> Then this happens when I try to do something that pulls data 558-1af0 ENTER SQLDriverConnectW HDBC 0x020DDA00 HWND 0x00000000 WCHAR * 0x73EF8634 [ -3] "******\ 0" SWORD -3 WCHAR * 0x73EF8634 SWORD -3 SWORD * 0x00000000 UWORD 0 <SQL_DRIVER_NOPROMPT> BMS 558-1af0 EXIT SQLDriverConnectW with return code -1 (SQL_ERROR) HDBC 0x020DDA00 HWND 0x00000000 WCHAR * 0x73EF8634 [ -3] "******\ 0" SWORD -3 WCHAR * 0x73EF8634 SWORD -3 SWORD * 0x00000000 UWORD 0 <SQL_DRIVER_NOPROMPT> DIAG [IM002] [Microsoft][ODBC Driver Manager] Data source name not found and no default driver specified (0) Nearly all of my searching on this issue comes up with programming issues where the connection string has a problem. The only thing that is different in this particular scenario though is Windows 7, I know the connection string is fine since it works on the XP machines. The VB components are supposed to be still functional under Win7. My computer is running 32 bit win7 and my VP is running Win7 64 bit and both have the same problem so that can be ruled out. I have already tried reinstalling the SQL Native Client and the VB runtime as well as the application in question. Hopefully I can find a solution and not have to resort to using the XP VM.

    Read the article

  • Proper Imaging Procedures to Restore and Deploy Image with Separate System Reserved Partition

    - by alharaka
    UPDATE: As per my experience here, no one responded. If I do not hear back from TechNet forum members about it, I will post a bounty here, if it makes a difference. I have banged my head against a wall for what seems like all week. I am going to explain my simple procedure, and how none of it, absolutely none, seems to work afterword despite few alternatives and everyone on the internet telling assuming this is how to do it. Diskpart Commands to Create FS Structure REM Select the disk targeted for deployment. REM REM NOTE: Usually disk 0, but drive failure can make it external USB REM media. This will erase the drive regardless! select disk 0 REM Remove previous formatting. clean REM Create System Reserved partition bootloader and files. create partition primary size=100 REM Format the volume format fs=ntfs label="System Reserved" quick override noerr REM Assign the System Reserved partition the D: mount for now assign letter=C REM The main system partition, size not specified to occupy whole drive. create partition primary REM Format the volume format fs=ntfs quick override noerr REM Assign the OS partition the D: mount for now assign letter=D REM Make this the active/bootable partition. sel disk 0 sel partition 1 active REM Close out the diskpart session. exit Now, I thought this was madness, but it turns out the System Reserved partition and standard "System Partition" (C:, commonly both the boot and system volumes where you find the Windows directory AND the bootmgr/ntldr hardware files, this is where Windows 7 diverges) as mounted in the Windows PE session where I run these commands do not matter. See reference here. Since this needs to be BitLocker-ready, enter this crappy System Reserved partition that is separate 100MB of awesome that goes before the regular boot volume. I do this, then I proceed to the next step. Deploy System Reserved and Normal System Images REM C is still the "System Reserved Partition", and the image is just like it sounds. imagex /apply G:\images\systemreserved.wim 1 C: REM D is now what will be the C: system partition on reboot, supposedly. imagex /apply G:\images\testimage.wim 1 D: Reboot the system Now, the images I just captured should look good. This is not even sysprepped, but reapplying the same fscking image I prepared on the same reference workstation hours before. Problem is I get 0xc000000e could not detect the accessible boot device \Windows\system32\winload.exe or different kinds of nonsense revolving around being able to find the boot volume with all the right files. I try different variations of things, now none of them work. I tried repairs with bcdboot, with a fresh System Reserved partition or not, bootrec, and maually editing the damn BCD store with bcdedit. I tried finalizing the above process with and without bootsect /nt60 C: /force. I need to wrap up and automate this procedure. What am I doing wrong that does not make the image happy, but really just miserable.

    Read the article

  • Problems migrating an EBS backed instance over AWS Regions

    - by gshankar
    Note: I asked this question on the EC2 forums too but haven't received any love there. Hopefully the ServerFault community will be more awesome. The new AWS Sydney region opening up is something that we've been waiting for for a long time but I'm having a lot of trouble migrating our instances over from N. California. I managed to migrate 1 instance over using CloudyScripts to move a snapshot and then firing up a new instance in the Sydney region. This was a very new instance so both the source and destination were running on a Ubuntu 12.04 LTS server and I had no issues there. However, the rest of our instances are all Ubuntu 10.04 LTS and with these, I'm having a lot of problems. I've tried following: 1- following the AWS whitepaper on moving instances which was given to us at the recent Customer Appreciation Day in Sydney where the new region was launched. The problem with this approach was with the last step (Step 19) here you register the image: ec2-register -s snap-0f62ec3f -n "Wombat" -d "migrated Wombat" --region ap-southeast-2 -a x86_64 --kernel aki-937e2ed6 --block-device-mapping "/dev/sdk=ephemeral0" I keep getting this error: Client.InvalidAMIID.NotFound: The AMI ID 'ami-937e2ed6' does not exist which I think is due to the kernel_id not existing in the Sydney region? 2- Using CloudyScripts to move a snapshot and then creating a new volume and attaching to a new instance in Sydney This results in the instance just hanging on boot and failing the status checks. I can't SSH in or look at the server log I suspect that my issue is with finding the right kernel_id for the volume in the new region. However I can't seem to work out how to go about finding this kernel_id, the ones I've tried (from the original instance) don't result in the Client.InvalidAMIID.NotFound: The AMI ID 'ami-937e2ed6' error and any other kernel_id just won't boot. I've tried both 12.04 and 10.04 versions of Ubuntu. Nothing seems to work, I've been banging my head against a wall for a while now, please help! New (broken) instance i-a1acda9b ami-9b8611a1 aki-31990e0b Source instance i-08a6664e ami-b37e2ef6 aki-937e2ed6 p.s. I also tried following this guide on updating my Ubuntu LTS version to 12.04 before doing the migration but it didn't seem to work either, still getting stuck on updating the kernel_id http://ubuntu-smoser.blogspot.com.au/2010/04/upgrading-ebs-instance.html

    Read the article

  • Is my Cisco switch port bad?

    - by ewwhite
    I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced last week, however the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link (switchport configuration pastebin). We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

    Read the article

  • "Error 1067: The process terminated unexpectedly" when trying to install MySQL on Win7 x64.

    - by Gravitas
    Hi, I've run into a brick wall trying to install MySQL v5.5 on my machine. My PC is Windows 7 x64, Enterprise edition. MySQL installs fine, but when I run the "MySQL Instance Configuration Wizard", it pauses forever on the step "Start Service" (I can let it run for 30 minutes with no response). If I go into services, I see that the "MySQL" service hasn't started, and if I try to start it, it says "Windows could not start MySQL Service on Local Computer. Error 1067: The process terminated unexpectedly." I've tried the following: Turning off firewall. Uninstalling all antivirus software. Installing / reinstalling 32-bit version of MySQL. Installing / reinstalling 64-bit version of MySQL. Uninstalling, deleting the contents of "C:\program files\MySQL" and "C:\program files (x86)\MySQL", reinstalling. Checking to see that there is no rogue services named MySQL???? (from a previous install). Checking that port 3306 is not used by an alternate program. Changing the default port that MySQL uses. Checking for "my.ini" and "my.ini.cnf" in "C:\windows" (nothing there but that can cause a problem). Running both MySQL installer, and configuration wizard, in "Adminstrator mode". Turning off UAC. Installing with defaults, not changing anything. Rebooting my machine (about 6 reboots so far). Opening up port 3306 in the firewall (both TCP and UDP, inbound and outbound). Swearing at the klutz of a programmer who designed MySQL so you can't even install it (as if that would help!) My machine is working 100% in every other way. InfiniDB (a MySQL compatible database) installs 100%, as does Visual Studio 2010, Microsoft SQL Server, etc, etc. Your advice on how to work around this? p.s. Here is the screen it got stuck on for 15 minutes until I killed the process: Update 2010-12-20 Tried MySQL v5.1, it didn't work either. Its amazing - if you type "mysqld /?", or "mysqld -help", it doesn't give you any help. And, if you try to restart the service manually, it doesn't display any error messages. Could it be any more unhelpful? Update 2010-12-21 Installed MySQL 6.0 alpha, and it worked. However, I'd rather not use an alpha release, given that the "stable" release is anything but :( Update 2010-12-21 Found http://dev.mysql.com/doc/refman/5.1/en/windows-troubleshooting.html, dealing with troubleshooting under Windows. Discovered that you can generate an error log if the service doesn't start - see here: http://dev.mysql.com/doc/refman/5.1/en/error-log.html

    Read the article

  • Automatic layout of manual network mapping

    - by Paul
    So I have a small business network mainly consisting of two routed layer-2 domains with a total of ca. 100 devices spread over ca. 2000m² production and office spaces. Typical problems to solve using the graph would be: Over what (cable) path is a PC connected to the server? Where to expect devices connected to a switch port? I want to generate a graph of the physical network topology: Nodes are endpoint devices, switch ports, wall outlets, patch panel ports etc. Edges are cable connections. Ideally, grouping edges (or segments) that pass through the same bundle could be grouped. Also I would like to augment the graph data with automatically gathered data (monitoring state, MAC address, Switch port <- MAC entries to build up parts of the map). At the moment I use graphviz for this inside a Confluence wiki like that: layout = "neato" overlap = scale subgraph { rankdir = "TB" subgraph cluster_r1pf1 { r1pf1 [label="{ Rack 1 PF 1 | { <p1>P1 | <p2>P2 | <p3>P3} }", shape=record] } subgraph cluster_switch1 { switch1 [label="{ Rack 1 Switch 1 | { <p1> P1 | <p1> P1 | <p3> P3} }", shape=record] } r1pf1:p1 -> switch1:p1 (obviously there are dozens of entries omitted here) Problem is: I have a hard time to influence graphviz to generate a bearable layout. Edges overlap so bad that you can't read the diagram anymore. The question is: What other tools (be it interactive like Visio, Omnigraffle or I/O-oriented like graphviz) exist that would allow an easily versionable (as in: Operates on a text file) documentation that is both machine and human readable and editable? Why not OmniGraffle or Visio? Well we don't have Macs and Visio is not available at the moment. To buy it I would need good arguments. Automation would be one of that. But last time I looked, versioning Visio files or even thinking about automatic handling was a nightmare. Related: Network Mapping Tools basically asks the same with a focus on generating the complete graph automatically (but without the need to document cabling connections) Recommendations for automatic computer inventory brings up links of "all-in-one" solutions

    Read the article

  • What is it that kills laptop batteries?

    - by Mala
    There are many superstitions on what you must never do lest your battery become worthless - and by worthless I mean hold about 16 - 24 seconds of charge. This has happened to every laptop I have ever owned, and I just got a new one, so please help me sort out fact from fiction. Here are some of the things I've heard: Do not keep your laptop fully charged. You must run it completely down every so often. Do not use your laptop plugged in to the wall. Only plug it in when it needs charge. If you will not be using your laptop for a long period of time, don't leave it at full charge. Do not leave your laptop running 24/7. The first two I know to be complete fiction: this was true of old batteries such as you might have had in an iPod in 2003, but modern batteries function better when kept at or near full charge. Devices even have circuitry to prevent you from completely depleting your battery, as this is dangerous. The third point sounds probable, and I'd be interested to know if it was true. However, it doesn't really apply to me because I'm not really the type to leave my laptop alone for a day, much less a "long period of time" The fourth seems most likely of the above, but only because of causality: I have always done this, and my batteries have always crapped out on me. I've generally treated a laptop like a desktop with a battery backup, and that I can move from one room to another if necessary. The fact that my batteries tend to last less than 30 seconds has further entrenched this behavior. Should I be trying to break this habit? Are there any other things that ruin laptop batteries? I love that I can actually use my new laptop unplugged :) I'd like to keep it that way. Update: Additional question: If the computer will be used for an extended period of time plugged in, does it make sense to remove the battery first? Update 2: I know people with laptops older than mine, who actively use their laptops as much as I do, and their batteries still hold about an hours' charge while mine holds less than 30 seconds, hence my belief that something I'm doing kills them.

    Read the article

  • Wirelss card not being detected in backtrack 5

    - by Jesse Nelson
    I just installed backtrack 5 and I am unable to detect my wireless card. iwconfig doesn't list my interface. I can see that the hardware is present in lspci -vnn (see below) but I can't get the interface detected. I have tried to reinstall the compat-wireless package but I get errors during the build (see below) I have done a ton of researching and I keep hitting a brick wall, mostly because the wiki for backtrack is down and I can't find any good resources. Does anyone know how to fix the issue? Also, does anyone no how I can scan the hardware to determine what NIC is assigning my interface? If I can figure out the interface name I think I can set it up manually by putting up the link and using wireless-tools to manually configure the connection, this is what I had to do in arch on my mac. As stated the wiki for backtrack is down and I can't find any help on the issue. I tried to do the full kernel upgrade suggested in my software update but after the update was complete and I logged back in I had a new log in manager and the only thing I was able to log into was window managers. However, after this update my wireless was working fine. Please help I am new to Linux and the wiki is down, I have nowhere else to turn. Forgot to mention I am using the KDE version, not Gnome. Thanks in advance for any help or support. Attempt at make: root@bt:/usr/src/compat-wireless-3.3-rc1-2# make /usr/src/compat-wireless-3.3-rc1-2/config.mk:254: "WARNING: CONFIG_CFG80211_WEXT will be deactivated or not working because kernel was compiled with CONFIG_WIRELESS_EXT=n. Tools using wext interface like iwconfig will not work. To activate it build your kernel e.g. with CONFIG_LIBIPW=m." make -C /lib/modules/2.6.38/build M=/usr/src/compat-wireless-3.3-rc1-2 modules make: *** /lib/modules/2.6.38/build: No such file or directory. Stop. make: *** [modules] Error 2 lspci output: root@bt:/usr/src/compat-wireless-3.3-rc1-2# lspci -vnn -i net lspci: I/O error at net, line 0 root@bt:/usr/src/compat-wireless-3.3-rc1-2# lspci -vnn 02:00.0 Network controller [0280]: Atheros Communications Inc. Device [168c:0032] (rev ff) (prog-if ff) !!! Unknown header type 7f ( This is the problem but I can't find the solution) Kernel modules: ath9k iwconfig output: root@bt:/usr/src/compat-wireless-3.3-rc1-2# iwconfig lo no wireless extensions. eth0 no wireless extensions.

    Read the article

  • Getting error while installing mod_wsgi in centos

    - by user825904
    I have reinstalled python with enable shared [root@master mod_wsgi-3.4]# make clean rm -rf .libs rm -f mod_wsgi.o mod_wsgi.la mod_wsgi.lo mod_wsgi.slo mod_wsgi.loT rm -f config.log config.status rm -rf autom4te.cache [root@master mod_wsgi-3.4]# LD_RUN_PATH=/usr/local/lib make apxs -c -I/usr/local/include/python2.7 -DNDEBUG mod_wsgi.c -L/usr/local/lib -L/usr/local/lib/python2.7/config -lpython2.7 -lpthread -ldl -lutil -lm /usr/lib64/apr-1/build/libtool --silent --mode=compile gcc -prefer-pic -O2 -g -pipe -Wall -Wp,-D_FORTIFY_SOURCE=2 -fexceptions -fstack-protector --param=ssp-buffer-size=4 -m64 -mtune=generic -Wformat-security -fno-strict-aliasing -DLINUX=2 -D_REENTRANT -D_GNU_SOURCE -pthread -I/usr/include/httpd -I/usr/include/apr-1 -I/usr/include/apr-1 -I/usr/local/include/python2.7 -DNDEBUG -c -o mod_wsgi.lo mod_wsgi.c && touch mod_wsgi.slo In file included from /usr/local/include/python2.7/Python.h:8, from mod_wsgi.c:142: /usr/local/include/python2.7/pyconfig.h:1161:1: warning: "_POSIX_C_SOURCE" redefined In file included from /usr/include/sys/types.h:26, from /usr/include/apr-1/apr-x86_64.h:127, from /usr/include/apr-1/apr.h:19, from /usr/include/httpd/ap_config.h:25, from /usr/include/httpd/httpd.h:43, from mod_wsgi.c:34: /usr/include/features.h:162:1: warning: this is the location of the previous definition In file included from /usr/local/include/python2.7/Python.h:8, from mod_wsgi.c:142: /usr/local/include/python2.7/pyconfig.h:1183:1: warning: "_XOPEN_SOURCE" redefined In file included from /usr/include/sys/types.h:26, from /usr/include/apr-1/apr-x86_64.h:127, from /usr/include/apr-1/apr.h:19, from /usr/include/httpd/ap_config.h:25, from /usr/include/httpd/httpd.h:43, from mod_wsgi.c:34: /usr/include/features.h:164:1: warning: this is the location of the previous definition mod_wsgi.c: In function ‘wsgi_server_group’: mod_wsgi.c:991: warning: unused variable ‘value’ mod_wsgi.c: In function ‘Log_isatty’: mod_wsgi.c:1665: warning: unused variable ‘result’ mod_wsgi.c: In function ‘Log_writelines’: mod_wsgi.c:1802: warning: unused variable ‘msg’ mod_wsgi.c: In function ‘Adapter_output’: mod_wsgi.c:3087: warning: unused variable ‘n’ mod_wsgi.c: In function ‘Adapter_file_wrapper’: mod_wsgi.c:4138: warning: unused variable ‘result’ mod_wsgi.c: In function ‘wsgi_python_term’: mod_wsgi.c:5850: warning: unused variable ‘tstate’ mod_wsgi.c:5849: warning: unused variable ‘interp’ mod_wsgi.c: In function ‘wsgi_python_child_init’: mod_wsgi.c:7050: warning: unused variable ‘l’ mod_wsgi.c:6948: warning: unused variable ‘interp’ mod_wsgi.c: In function ‘wsgi_add_import_script’: mod_wsgi.c:7701: warning: unused variable ‘error’ mod_wsgi.c: In function ‘wsgi_add_handler_script’: mod_wsgi.c:8179: warning: unused variable ‘dconfig’ mod_wsgi.c:8178: warning: unused variable ‘sconfig’ mod_wsgi.c: In function ‘wsgi_hook_handler’: mod_wsgi.c:9375: warning: suggest parentheses around assignment used as truth value mod_wsgi.c:9377: warning: suggest parentheses around assignment used as truth value mod_wsgi.c:9379: warning: suggest parentheses around assignment used as truth value mod_wsgi.c:9383: warning: suggest parentheses around assignment used as truth value mod_wsgi.c:9403: warning: suggest parentheses around assignment used as truth value mod_wsgi.c:9405: warning: suggest parentheses around assignment used as truth value mod_wsgi.c:9408: warning: suggest parentheses around assignment used as truth value mod_wsgi.c: In function ‘wsgi_daemon_worker’: mod_wsgi.c:10819: warning: unused variable ‘duration’ mod_wsgi.c:10818: warning: unused variable ‘start’ mod_wsgi.c: In function ‘wsgi_hook_daemon_handler’: mod_wsgi.c:13172: warning: unused variable ‘i’ mod_wsgi.c:13170: warning: unused variable ‘elts’ mod_wsgi.c:13169: warning: unused variable ‘head’ mod_wsgi.c: At top level: mod_wsgi.c:8142: warning: ‘wsgi_set_user_authoritative’ defined but not used mod_wsgi.c:15251: warning: ‘wsgi_hook_check_user_id’ defined but not used /usr/lib64/apr-1/build/libtool --silent --mode=link gcc -o mod_wsgi.la -rpath /usr/lib64/httpd/modules -module -avoid-version mod_wsgi.lo -L/usr/local/lib -L/usr/local/lib/python2.7/config -lpython2.7 -lpthread -ldl -lutil -lm

    Read the article

  • tc rules block traffic from some hosts at network

    - by user139430
    I have a problem I can not solve. The script, which sets the rules for traffic shaping is blocking the traffic from some hosts.If I remove all the rules, then it works. I can not understand why? Here is my script... #!/bin/sh cmdTC=/sbin/tc rateLANDl="60mbit" ceilLANDl="60mbit" rateLANUl="40mbit" ceilLANUl="40mbit" quantLAN="1514" # Nowaday bandwidth limit set to 100mbit. # We devide it with 60mbit download and 40mbit upload bandthes. rateHiDl="30mbit" ceilHiDl="60mbit" rateHiUl="20mbit" ceilHiUl="40mbit" quantHi="1514" rateLoDl="30mbit" ceilLoDl="60mbit" rateLoUl="20mbit" ceilLoUl="40mbit" quantLo="1514" devNIF=eth0 devFIF=ifb0 modprobe ifb ip link set $devFIF up 2>/dev/null #exit 0 ################################################################################################ # Remove discuiplines from network and fake interfaces ################################################################################################ $cmdTC qdisc del dev $devNIF root 2>/dev/null $cmdTC qdisc del dev $devFIF root 2>/dev/null $cmdTC qdisc del dev $devNIF ingress 2>/dev/null if [ "$1" = "down" ]; then exit 0 fi ################################################################################################ # Create discuiplines for network interface ################################################################################################ $cmdTC qdisc add dev $devNIF root handle 1:0 htb default 12 # Create classes for network interface $cmdTC class add dev $devNIF parent 1:0 classid 1:1 htb rate ${rateLANDl} ceil ${ceilLANDl} quantum ${quantLAN} $cmdTC class add dev $devNIF parent 1:1 classid 1:11 htb rate ${rateHiDl} ceil ${ceilHiDl} quantum ${quantHi} $cmdTC class add dev $devNIF parent 1:1 classid 1:12 htb rate ${rateLoDl} ceil ${ceilLoDl} quantum ${quantLo} $cmdTC qdisc add dev $devNIF parent 1:11 handle 111: sfq perturb 10 $cmdTC qdisc add dev $devNIF parent 1:12 handle 112: sfq perturb 10 # Create filters for network interface $cmdTC filter add dev $devNIF protocol all parent 1:0 u32 match ip dst 10.252.2.0/24 flowid 1:11 $cmdTC filter add dev $devNIF protocol all parent 111: handle 111 flow hash keys dst divisor 1024 baseclass 1:11 $cmdTC filter add dev $devNIF protocol all parent 112: handle 112 flow hash keys dst divisor 1024 baseclass 1:12 ################################################################################################ # Create discuiplines for fake interface ################################################################################################ $cmdTC qdisc add dev $devFIF root handle 1:0 htb default 12 # Create classes for network interface $cmdTC class add dev $devFIF parent 1:0 classid 1:1 htb rate ${rateLANUl} ceil ${ceilLANUl} quantum ${quantLAN} $cmdTC class add dev $devFIF parent 1:1 classid 1:11 htb rate ${rateHiUl} ceil ${ceilHiUl} quantum ${quantHi} $cmdTC class add dev $devFIF parent 1:1 classid 1:12 htb rate ${rateLoUl} ceil ${ceilLoUl} quantum ${quantLo} $cmdTC qdisc add dev $devFIF parent 1:11 handle 111: sfq perturb 10 $cmdTC qdisc add dev $devFIF parent 1:12 handle 112: sfq perturb 10 # Create filters for network interface $cmdTC filter add dev $devFIF protocol all parent 1:0 u32 match ip src 10.252.2.0/24 flowid 1:11 $cmdTC filter add dev $devFIF protocol all parent 111: handle 111 flow hash keys src divisor 1024 baseclass 1:11 $cmdTC filter add dev $devFIF protocol all parent 112: handle 112 flow hash keys src divisor 1024 baseclass 1:12 ################################################################################################ # Create redirect discuiplines from network to fake interface ################################################################################################ $cmdTC qdisc add dev $devNIF handle ffff:0 ingress $cmdTC filter add dev $devNIF parent ffff:0 protocol all u32 match u32 0 0 action mirred egress redirect dev $devFIF Here is my /etc/modules: loop ifb ppp_mppe nf_conntrack_pptp nt_conntrack_proto_gre nf_nat_pptp nf_nat_proto_gre The system is Linux wall 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux

    Read the article

  • Frequent and weird wifi disconnections

    - by Sidou
    How would you explain, troubleshoot (and solve) the following problem? Wifi ADSL modem router D-link 2640R installed in living room at about 1.8m height. Working fine, synchronising and getting/serving stable internet connection. First situation: -Laptop 01 in other end of the house, let's say in room01 southern to the living room, distant by about 15m. Getting stable signal of good to very good quality. No disconnection. -Laptop 02 in room02 opposite to room01 (5m West) which makes it almost at the same distance and direction from the router located 15m North. Getting stable signal of good to very good quality. No disconnection. Second situation: -Laptop 01 moved to room03 Northern to the living room (actually just 3m behind the wall where the router lies). Getting stable signal of excellent quality. No disconnection. -Laptop 02 still in room02 but now experiences frequent disconnections (actually almost impossible to get the Internet even though the signal level is still very good. Either no Internet with the wifi icon appearing connected to access point or no connection established at all which happens every 2 minutes and that means virtually no Internet at all as I can just get a timeframe of 1 minute or so to load any website or even get to the router's web based control panel. If Laptop 01 is completely shut down or its wifi adapters shut down or even still working but its wifi MAC address forbidden, then Laptop 02 has no problem at all. If Laptop 02 is moved to a nearer location to the router, in the living room for instance, then no connection problem occurs even if Laptop 01 is also connected. And also if we move back Laptop 01 to its original location (room 01), then no problem as well. I'm completely lost and don't know how to address this issue. I tried to change the Wifi channel and even tried the auto channel scan but that didn't solve it. I know that the problem is probably coming from Laptop 01 being in its new location or some sort of interference as the problem occurs only under the described condition but I have no idea how to solve it! I also scanned the neighborhood for wifi jam using InSSIDer, there are few other access points but they don't seem to affect the situation. Any ideas about the steps to follow or tools to use ?

    Read the article

  • D-Link DIR-300 slows down / loses network

    - by basic6
    there are 2 buildings (A and B). In bldg A is an open WLAN (which I'm allowed to use btw). In bldg B is a computer that I want to connect to that network. So I flashed an old D-Link DIR-300 AP with DD-WRT, mounted it to the wall (bldg B) near a window, attached a 13 dBi directional antenna (pointing to bldg A) and configured it as AP client in that wireless network. Then there's another AP, connected to the D-Link AP, acting as standard access point, which the computer is connected to. That's basically working so far, but: Every now and then the connection is lost. Not the connection between the computer and the D-Link (I can access the DD-WRT admin page normally) or the connection between the D-Link and the WLAN (in Status - Wireless it says it's still connected to the network), but when I want to access a web page (which only works if I'm connected to the wireless network from bldg A), my Firefox keeps "Looking for" (name resolution) without finding anything. When I reset the D-Link (power off, power on) in this situation, after some moments, everything's working fine again (Internet access). I've no idea why this is happening, but usually it's at most every few weeks (most times when nobody was using the computer, so no traffic). Compared to the connection speed when I connect directly to the WLAN in bldg A (Laptop), the speed in bldg B is rather slow, but I have the impression that this difference is worse in the last few days. A few minutes ago, I got 582 KB/s down and 911 KB/s up in bldg A (directly/laptop) and 84 KB/s down and 9 KB/s up in bldg B. The speed in bldg B used to be way higher (I remember 200 KB/s up) while the actual network speed in bldg A was lower than it is now (close to those 200). I'm aware that the wireless connection between those buildings should slow things down, but I'm wondering why this difference has become that extreme. Thanks for any tips... Update: I currently want to upload a large file (1.5 GB) via FTP (FileZilla). Since that caused the D-Link to disconnect (as described in first post), I took my laptop to bldg A, connected directly to the original WLAN (bypassing my D-Link) and tried the same upload. Guess what - same issue: At some point the connection is dead (at this point I would have reset my D-Link if I was connected to it). Just as the D-Link, my laptop is still connected, but not even name resolution is working ("Looking for..." in Firefox). After reconnecting, it's working again. Maybe my D-Link isn't the problem at all...

    Read the article

  • What router hardware or software should be used when multiple public IPs are routed into the same LAN?

    - by lcbrevard
    I am looking for recommendations to replace a set of consumer grade (Linksys, Netgear, Belkin) routers with something that can handle more traffic while routing more than one static public IP into the same LAN address space. We have a block of static public IPs, 5 usable, with Comcast Business. Currently four of them are in use for: General office access Web server Mail and DNS servers Download and backup web server for separate business All systems (a mixture of physical and virtual) are in the same LAN address space (10.x.y.0/24) to enable easy access between them inside the office. There are 30 or more systems in use depending on which virtual machines are currently active. We have a mixture of Windows, Linux, FreeBSD, and Solaris. Currently a separate consumer grade router is used for each of the four static addresses, with its WAN address set to the specific static address and a different gateway address for each: uses 10.x.y.1 - various ports are forwarded to various LAN IPs on systems with gateway 10.x.y.1 uses 10.x.y.254 - port 80 is forwarded to a server with gateway 10.x.y.254 uses 10.x.y.253 - ports for mail and dns are forwarded to a server with gateway 10.x.y.253 uses 10.x.y.252 - ports as needed are forwarded to server with gateway 10.x.y.252 Only router 1. is allowed to serve DHCP and address reservation based on the MAC is used for most of the internal "server" IP addresses so they are at fixed values. [Some are set static due to limitations in the address reservation capabilities of router 1.] And, yes, this really does work! But... I am looking for: better DHCP with more capable address reservation higher capacity so I don't have to periodically power cycle the routers One obvious improvement would be to have a real DHCP server and not use a consumer grade router for that purpose. I am torn between buying a "professional" router such as Cisco or Juniper or Sonic Wall verus learning to configure some spare hardware to perform this function. The price goes up extremely rapidly with capabilities for commercial routers! Worse, some routers require licensing based on the number of clients - a disaster in our environment with so many virtual machines. Sorry for such a long posting but I am getting tired of having to power cycle routers and deal with shifting IP addresses afterwards!

    Read the article

  • AGENT: The World's Smartest Watch

    - by Rob Chartier
    AGENT: The World's Smartest Watch by Secret Labs + House of Horology Disclaimer: Most if not all of this content has been gleaned from the comments on the Kickstarter project page and comments section. Any discrepancies between this post and any documentation on agentwatches.com, kickstarter.com, etc.., those official sites take precedence. Overview The next generation smartwatch with brand-new technology. World-class developer tools, unparalleled battery life, Qi wireless charging. Kickstarter Page, Comments Funding period : May 21, 2013 - Jun 20, 2013 MSRP : $249 Other Urls http://www.agentwatches.com/ https://www.facebook.com/agentwatches http://twitter.com/agentwatches http://pinterest.com/agentwatches/ http://paper.li/robchartier/1371234640 Developer Story The first official launch of the preview SDK and emulator will happen on 20-Jun-2013.  All development will be done in Visual Studio 2012, using the .NET Micro Framework SDK 2.3.  The SDK will ship with the first round of the expected API for developers along with an emulator. With that said, there is no need to wait for the SDK.  You can download the tooling now and get started with Apps and Faces immediately.  The only thing that you will not be able to work with is the API; but for example, watch faces, you can start building the basic face rendering with the Bitmap graphics drawing in the .NET Micro Framework.   Does it look good? Before we dig into any more of the gory details, here are a few photos of the current available prototype models.   The watch on the tiny QI Charter   If you wander too far away from your phone, your watch will let you know with a vibration and a message, all but one button will dismiss the message.   An app showing the premium weather data!   Nice stitching on the straps, leather and silicon will be available, along with a few lengths to choose from (short, regular, long lengths). On to those gory details…. Hardware Specs Processor 120MHz ARM Cortex-M4 processor (ATSAM4SD32) with secondary AVR co-processor Flash & RAM 2MB of onboard flash and 160KB of RAM 1/4 of the onboard flash will be used by the OS The flash is permanent (non-volatile) storage. Bluetooth Bluetooth 4.0 BD/EDR + LE Bluetooth 4.0 is backwards compatible with Bluetooth 2.1, so classic Bluetooth functions (BD/EDR, SPP/AVRCP/PBAP/etc.) will work fine. Sensors 3D Accelerometer (Motion) ST LSM303DLHC Ambient Light Sensor Hardware power metering Vibration Motor (You can pulse it to create vibration patterns, not sure about the vibration strength - driven with PWM) No piezo/speaker or microphone. Other QI Wireless Charging, no NFC, no wall adapter included Custom LED Backlight No GPS in the watch. It uses the GPS in your phone. AGENT watch apps are deployed and debugged wirelessly from your PC via Bluetooth. RoHS, Pb-free Battery Expected to use a CR2430-sized rechargeable battery – replaceable (Mouser, Amazon) Estimated charging time from empty is 2 hours with provided charger 7 Days typical with Bluetooth on, 30 days with Bluetooth off (watch-face only mode) The battery should last at least 2 years, with 100s of charge cycles. Physical dimensions Roughly 38mm top-to-bottom on the front face 35mm left-to-right on the front face and around 12mm in depth 22mm strap Two ~1/16" hex screws to attach the watch pin The top watchcase material candidates are PVD stainless steel, brushed matte ceramic, and high-quality polycarbonate (TBD). The glass lens is mineral glass, Anti-glare glass lens Strap options Leather and silicon straps will be available Expected to have three sizes Display 1.28" Sharp Memory Display The display stays on 100% of the time. Dimensions: 128x128 pixels Buttons Custom "Pusher" buttons, they will not make noise like a mouse click, and are very durable. The top-left button activates the backlight; bottom-left changes apps; three buttons on the right are up/select/down and can be used for custom purposes by apps. Backup reset procedure is currently activated by holding the home/menu button and the top-right user button for about ten seconds Device Support Android 2.3 or newer iPhone 4S or newer Windows Phone 8 or newer Heart Rate monitors - Bluetooth SPP or Bluetooth LE (GATT) is what you'll want the heart monitor to support. Almost limitless Bluetooth device support! Internationalization & Localization Full UTF8 Support from the ground up. AGENT's user interface is in English. Your content (caller ID, music tracks, notifications) will be in your native language. We have a plan to cover most major character sets, with Latin characters pre-loaded on the watch. Simplified Chinese will be available Feature overview Phone lost alert Caller ID Music Control (possible volume control) Wireless Charging Timer Stopwatch Vibrating Alarm (possibly custom vibrations for caller id) A few default watch faces Airplane mode (by demand or low power) Can be turned off completely Customizable 3rd party watch faces, applications which can be loaded over bluetooth. Sample apps that maybe installed Weather Sample Apps not installed Exercise App Other Possible Skype integration over Bluetooth. They will provide an AGENT app for your smartphone (iPhone, Android, Windows Phone). You'll be able to use it to load apps onto the watch.. You will be able to cancel phone calls. With compatible phones you can also answer, end, etc. They are adopting the standard hands-free profile to provide these features and caller ID.

    Read the article

  • Nerdstock 2012: A photo review of Microsoft TechEd North America 2012

    - by The Un-T Guy
    Not only could I not fathom that I would ever be attending a tech event of the magnitude of TechEd, neither could any of my co-workers.  As the least technical person in the history of Information Technology ever, I felt as though I were walking into the belly of the beast, fearing I’d not be allowed out until I could write SSIS packages, program in Visual Basic, or at least arm wrestle a DBA.  Most of my fears were unrealized.   But I made it.  I was here.  I even got to wear the Mark of the Geek neck package with schedule, eyeglass cleaners, name badge (company name obfuscated so they don’t fire me), and a pen.  The name  badge was seemingly the key element, as every vendor in the place wanted to scan it to capture name, email address, and numbers to show their bosses back home.  It also let me eat the food and drink the coffee so that’s a fair trade.   A recurring theme throughout the presentations and vendor demos was “the Cloud” and BYOD (bring your own device).  The below was a common site throughout the week, as attendees from all over the world brought their own devices and were able to (seemingly) seamlessly connect to the Worldwide Innerwebs.  Apparently proof that Microsoft and the event organizers were practicing what they were preaching.   “Cavernous” is one way to describe the downstairs facility itself.  “Freaking cavernous” might be more accurate.  Work sessions were held in classrooms on the second and third floors but the real action was happening downstairs.  Microsoft bookstore, blogger hub (shoutout to Geekswithblogs.net), The Wall (sans Pink Floyd, sadly), couches, recharging stations…   …a game zone with pool and air hockey tables, pinball machines, foosball…   …vintage video games…           …and a even giant chess board.  Looked like this guy was opening with the Kaspersky parry.   The blend of technology and fantasy even went so far as to bring childhood favorites to life.  Assuming, of course, your childhood was pre-video games (like mine) and you were stuck with electric football and Rock ‘em Sock ‘em robots:   And, lest the “combatants” become unruly or – God forbid – afternoon snacks were late, Orange County’s finest was on the scene to keep the peace.  On a high-tech mode of transport, of course.   She wasn’t the only one to think this was a swell way to transition from one concourse to the next.  Given the level of support provided by the entire Orange County Convention Center staff, I knew they had to have some secret.   Here’s one entrance to the vendor zone/”Technical Learning Center.”  Couldn’t help but think of them as the remora attached to the Whale Shark that is Microsoft…   …or perhaps planets orbiting the sun. Microsoft is just that huge and it seemed like every vendor in the industry looks forward to partnering with the tech behemoth.   Aside from the free stuff from the vendors, probably the most popular place in the house was the dining area.  Amazing spreads every day, multiple times a day.  While no attendance numbers were available at press time, literally thousands of attendees were fed, and fed well, every day.  And lest you think my post from earlier in the week exaggerated about the backpacks…   …or that I’m exaggerating about the lunch crowds.  This represents only about between 25-30% of the lunch crowd – it was all my camera could capture at once.  No one went away hungry.   The only thing missing was a a vat of Red Bull but apparently organizers went old school, with probably 100 urns of the original energy drink – coffee – all around the venue.   Of course, following lunch and afternoon sessions, some preferred the even older school method of re-energizing.  There were rumors that Microsoft was serving graham crackers and milk in this area.  But they were only rumors.   Cannot overstate the wonderful service provided by the Orange County Convention Center staff.  Coffee, soft drinks, juice, and water were available always.  Buffet meals were delicious with a wide range of healthy options available, in addition to hundreds (at least) special meal requests supported every day.  Ever tried to keep up with an estimated 9,000 hungry and thirsty IT-ers?  These folks did.  Kudos to all of the staff and many thanks!   And while I occasionally poke fun at the Whale Shark, if nothing else this experience convinced me of one thing:  Microsoft knows how to put on a professional event.  Hundreds of informative, professionally delivered sessions, covering a wide range of topics set at varying levels of expertise (some that even I was able to follow), social activities, vendor partnerships…they brought everything you could ask for to inform, educate, and inspire an entire IT industry.   So as I depart the belly of the beast, I can both take pride in the fact that I survived the week and marvel at the brilliance surrounding me.  The IT industry – or at least the segment associated with Microsoft – is in good, professional hands.  And what won’t fit in their hands can be toted in the Microsoft provided backpacks.  Win-win.   Until New Orleans…

    Read the article

< Previous Page | 47 48 49 50 51 52 53 54 55 56 57 58  | Next Page >