Search Results

Search found 1456 results on 59 pages for 'wall'.

Page 55/59 | < Previous Page | 51 52 53 54 55 56 57 58 59  | Next Page >

  • Visiting the Emtel Data Centre

    Back in February at the first event of the Emtel Knowledge Series (EKS) I spoke to various people at Emtel about their data centre here on the island. I was trying to see whether it would be possible to arrange a meeting over there for a selected group of our community members. Well, let's say it like this... My first approach wasn't that promising and far from successful but during the following months there were more and more occasions to get in touch with the "right" contact persons at Emtel to make it happen... Setting up an appointment and pre-requisites The major improvement came during a Boot Camp for Windows Phone 8.1 App development organised by Microsoft Indian Ocean Islands in cooperation with Emtel at the Emtel World, Ebene. Apart from learning bits and pieces regarding Universal Apps I took the opportunity to get in touch with Arvin Lockee, Sales Executive - Data, during our lunch break. And this really kicked off the whole procedure. Prior to get access to the Emtel data centre it is requested that you provide full name and National ID of anyone going to visit. Also, it should be noted that there was only a limited amount of seats available. Anyways, packed with this information I posted through the usual social media channels. Responses came in very quickly and based on First-come, first-serve (FCFS) principle I noted down the details and forwarded them to Emtel in order to fix a date and time for the visit. In preparation on our side, all attendees exchanged contact details and we organised transport options to go to the data centre in Arsenal. The day before and on the day of our meeting, Arvin send me a reminder to check whether everything is still confirmed and ready to go... Of course, it was! Arriving at the Emtel Data Centre As I'm coming from Flic En Flac towards the North, we agreed that I'm going to pick up a couple of young fellows near the old post office in Port Louis. All went well, except that Sean eventually might be living in another time zone compared to the rest of us. Anyway, after some extended stop we were complete and arrived just in time in Arsenal to meet and greet with Ish and Veer. Again, Emtel is taking access procedures to their data centre very serious and the gate stayed close until all our IDs had been noted and compared to the list of registered attendees. Despite having a good laugh at the mixture of old and new ID cards it was a straight-forward processing. The ward was very helpful and guided us to the waiting area at the entrance section of the building. Shortly after we were welcomed by Kamlesh Bokhoree, the Data Centre Officer. He gave us brief introduction into the rules and regulations during our visit, like no photography allowed, not touching the buttons, and following his instructions through the whole visit. Of course! Inside the data centre Next, he explained us the multi-factor authentication system using a combination of bio-metric data, like finger print reader, and "classic" pin panel. The Emtel data centre provides multiple services and next to co-location for your own hardware they also offer storage options for your backup and archive data in their massive, fire-resistant vault. Very impressive to get to know about the considerations that have been done in choosing the right location and how to set up the whole premises. It should also be noted that there is 24/7 CCTV surveillance inside and outside the buildings. Strengths of the Emtel TIER 3 Data Centre, Mauritius Finally, we were guided into the first server room. And wow, the whole setup is cleverly planned and outlined in the architecture. From the false floor and ceilings in order to provide optimum air flow, over to the separation of cold and hot aisles between the full-size server racks, and of course the monitored air conditions in order to analyse and watch changes in temperature, smoke detection and other parameters. And not surprisingly everything has been implemented in two independent circuits. There is a standardised classification for the construction and operation of data centres world-wide, and the Emtel's one has been designed to be a TIER 4 building but due to the lack of an alternative power supplier on the island it is officially registered as a TIER 3 compliant data centre. Maybe in the long run there might be a second supplier of energy next to CEB... time will tell. Luckily, the data centre is integrated into the National Fibre Optic Gigabit Ring and Emtel already connects internationally through diverse undersea cable routes like SAFE & LION/LION2 out of Mauritius and through several other providers for onwards connectivity. The data centre is part of the National Fibre Optic Gigabit Ring and has redundant internet connectivity onwards. Meanwhile, Arvin managed to join our little group of geeks and he supported Kamlesh in answering our technical questions regarding the capacities and general operation of the data centre. Visiting the NOC and its dedicated team of IT professionals was surely one of the visual highlights. Seeing their wall of screens to monitor any kind of activities on the data lines, the managed servers and the activity in and around the building was great. Even though I'm using a multi-head setup since years I cannot keep it up with that setup... ;-) But I got a couple of ideas on how to improve my work spaces here at the office. Clear advantages of hosting your e-commerce and mobile backends locally After the completely isolated NOC area we continued our Q&A session with Kamlesh and Arvin in the second server room which is dedictated to shared environments. On first thought it should be well-noted that there is lots of space for full-sized racks and therefore co-location of your own hardware. Actually, given the feedback that there will be upcoming changes in prices the facilities at the Emtel data centre are getting more and more competitive and interesting for local companies, especially small and medium enterprises. After seeing this world-class infrastructure available on the island, I'm already considering of moving one of my root servers abroad to be co-located here on the island. This would provide an improved user experience in terms of site performance and latency. This would be a good improvement, especially for upcoming e-commerce solutions for two of my local clients. Later on, we actually started the conversation of additional services that could be a catalyst for the local market in order to attract more small and medium companies to take the data centre into their evaluations regarding online activities. Until today Emtel does not provide virtualised server environments but there might be ongoing plans in the future to cover this field as well. Emtel is a mobile operator and internet connectivity provider in the first place, entering a market of managed and virtualised server infrastructures including capacities in terms of cloud storage and computing are rather new and there is a continuous learning curve at Emtel, too. You cannot just jump into a new market and see how it works out... And I appreciate Emtel's approach towards a solid fundament and then building new services on top of that. Emtel as a future one-stop-shop service provider for all your internet and telecommunications needs. Emtel's promotional video about their TIER 3 data centre in Arsenal, Mauritius More details are thoroughly described in Emtel's brochure of their data centre. Check out their PDF document here. Thanks for this opportunity Visiting and walking through the Emtel data centre for more than 2 hours was a great experience. As representative of the Mauritius Software Craftsmanship Community (MSCC) I would like to thank anyone at Emtel involved in the process of making it happen, and especially to Arvin Lockee and Kamlesh Bokhoree for their time and patience in explaining the infrastructure and answering all the endless questions from our members. Thank You!

    Read the article

  • Netgear VPN endpoint drops connectivity to single IP address

    - by Justin Bowers
    I'm having a strange issue with one of the networks I manage recently. We have about 14 different networks connected together through a Netgear hardware VPN. Everything has been running fine (other than standard connectivity problems) for a few years now, but I've hit a wall with a problem that's just cropped up at one of the VPN endpoint locations. Our primary VPN network is on the 192.168.1.0/24 subnet and our other 13 networks are on the 192.168.2.0/24 - 192.168.14.0/24 subnets. We run a terminal server on the 192.168.1.0/24 network with IP address 192.168.1.100. Starting Thursday of last week, we had a problem with connectivity of the 192.168.2.0/24 network to 192.168.1.100. When troubleshooting the problem, I found that Network 2 (192.168.2.0/24) still had connectivity to the Internet as well as VPN connectivity to Network 1 (192.168.1.0/24). We could ping and connect to any other device other than the server with IP address 192.168.1.100. Also, none of our networks had an issue accessing 192.168.1.100. I ran a scan on Network 2 after assigning static IP addresses to one of the workstations but received no response from 192.168.1.100 (looking for possibly a new device that someone had plugged into Network 2 that had a duplicate IP address with the server). Asking the staff, noone had reported connecting a new device to Network 2 as well. I then assigned a secondary IP address of 192.168.1.88 to the server and could ping and connect to the secondary IP address from Network 2, but still couldn't access it via 192.168.1.100. I then just rebooted the Netgear VPN Firewall (FVS318v3) and after it came back up, connectivity to 192.168.1.100 was restored. Beforehand, when checking for devices with a possible duplicate IP address, I did run a check for available wireless access points and stations and found none (our wireless is secured via MAC address access control through a WG102 device). I thought that it may have been a fluke for some reason since everything came back up after a power cycle of the VPN Firewall. Things ran fine for a few days until this afternoon, when the problem happened again. One of our users claimed that they had connectivity problems to the server and after connecting to the computer, I found that I couldn't ping the server address anymore. I could still ping the alternate IP address of the server though, so I went ahead and rebooted the VPN firewall again and connectivity was restored. Unfortunately, I can't find anything in the security or VPN logs of the firewall that helps point me in the right direction, so I thought I would go ahead and ask to see if anyone else has any other insight into why we've started having this problem. I am aware that it could still be a device with a duplicate IP address of the server on Network 2, but every employee claim states that there's been no such new device brought in to the network. I know this is a long read, but any help is appreciated! Thanks, Justin

    Read the article

  • Crash in audio resampler with some audio rates - FFMPEG PHP ( Solved! )

    - by Olaf Erlandsen
    i have a problem with this command( FFMPEG PHP ): Command: ffmpeg -i 62f76f050494f0ed6a5997967c00c0c0.wmv -ss 0 -t 99 -y -ar 44100 -async 44100 -r 29.970 -ac 2 -qscale 5 -f flv 62f76f050494f0ed6a5997967c00c0c0.flv Output: FFmpeg version 0.6.5, Copyright (c) 2000-2010 the FFmpeg developers built on Jan 29 2012 17:52:15 with gcc 4.4.5 20110214 (Red Hat 4.4.5-6) configuration: --prefix=/usr --libdir=/usr/lib64 --shlibdir=/usr/lib64 --mandir=/usr/share/man --incdir=/usr/include --disable-avisynth --extra-cflags='-O2 -g -pipe -Wall -Wp,-D_FORTIFY_SOURCE=2 -fexceptions -fstack-protector --param=ssp-buffer-size=4 -m64 -mtune=generic -fPIC' --enable-avfilter --enable-avfilter-lavf --enable-libdc1394 --enable-libdirac --enable-libfaac --enable-libfaad --enable-libfaadbin --enable-libgsm --enable-libmp3lame --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-librtmp --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libx264 --enable-gpl --enable-nonfree --enable-postproc --enable-pthreads --enable-shared --enable-swscale --enable-vdpau --enable-version3 --enable-x11grab libavutil 50.15. 1 / 50.15. 1 libavcodec 52.72. 2 / 52.72. 2 libavformat 52.64. 2 / 52.64. 2 libavdevice 52. 2. 0 / 52. 2. 0 libavfilter 1.19. 0 / 1.19. 0 libswscale 0.11. 0 / 0.11. 0 libpostproc 51. 2. 0 / 51. 2. 0 [asf @ 0xe81670]max_analyze_duration reached Input #0, asf, from '/var/www/resources/tmp/62f76f050494f0ed6a5997967c00c0c0.wmv': Metadata: WMFSDKVersion : 12.0.7601.17514 WMFSDKNeeded : 0.0.0.0000 IsVBR : 0 Duration: 00:00:50.87, bitrate: 2467 kb/s Stream #0.0: Audio: wmapro, 44100 Hz, stereo, flt, 256 kb/s Stream #0.1: Video: vc1, yuv420p, 950x460 [PAR 1:1 DAR 95:46], 25 fps, 25 tbr, 1k tbn, 25 tbc Output #0, flv, to '/var/www/resources/media/62f76f050494f0ed6a5997967c00c0c0.flv': Metadata: encoder : Lavf52.64.2 Stream #0.0: Video: flv, yuv420p, 950x460 [PAR 1:1 DAR 95:46], q=2-31, 200 kb/s, 1k tbn, 29.97 tbc Stream #0.1: Audio: libmp3lame, 11025 Hz, stereo, s16, 64 kb/s Stream mapping: Stream #0.1 -> #0.0 Stream #0.0 -> #0.1 Press [q] to stop encoding frame= 72 fps= 0 q=5.0 size= 0kB time=10.91 bitrate= 0.0kbits/s Multiple frames in a packet from stream 0 Warning, using s16 intermediate sample format for resampling frame= 141 fps=139 q=5.0 size= 103kB time=8.15 bitrate= 103.2kbits/s frame= 220 fps=144 q=5.0 size= 875kB time=10.92 bitrate= 656.6kbits/s frame= 290 fps=143 q=5.0 size= 1525kB time=13.74 bitrate= 909.1kbits/s frame= 356 fps=141 q=5.0 size= 2153kB time=15.99 bitrate=1103.1kbits/s frame= 427 fps=141 q=5.0 size= 2847kB time=18.70 bitrate=1247.0kbits/s frame= 497 fps=141 q=5.0 size= 3771kB time=21.16 bitrate=1460.0kbits/s frame= 575 fps=142 q=5.0 size= 4695kB time=24.61 bitrate=1563.0kbits/s frame= 639 fps=141 q=5.0 size= 5301kB time=26.80 bitrate=1620.2kbits/s frame= 703 fps=139 q=5.0 size= 5829kB time=29.36 bitrate=1626.2kbits/s frame= 774 fps=139 q=5.0 size= 6659kB time=32.39 bitrate=1684.0kbits/s frame= 842 fps=139 q=5.0 size= 7915kB time=35.27 bitrate=1838.6kbits/s frame= 911 fps=139 q=5.0 size= 9011kB time=37.98 bitrate=1943.4kbits/s frame= 975 fps=138 q=5.0 size= 9788kB time=40.59 bitrate=1975.3kbits/s frame= 1041 fps=138 q=5.0 size= 10904kB time=43.83 bitrate=2037.9kbits/s frame= 1115 fps=138 q=5.0 size= 11795kB time=46.24 bitrate=2089.8kbits/s frame= 1183 fps=138 q=5.0 size= 12678kB time=48.74 bitrate=2130.7kbits/s frame= 1247 fps=137 q=5.0 size= 13964kB time=51.36 bitrate=2227.5kbits/s frame= 1271 fps=136 q=5.0 Lsize= 15865kB time=58.86 bitrate=2208.1kbits/s video:15366kB audio:462kB global headers:0kB muxing overhead 0.238956% Problem: Warning, using s16 intermediate sample format for resampling I've also tried changing the parameter From -ar 44100 to -ar 11025 Thanks! Solution: Read this link: http://en.wikipedia.org/wiki/MP3#Bit_rate

    Read the article

  • Dell Studio 1737 Overheating

    - by Sean
    I am using a Dell Studio 1737 laptop. I have been running Linux and have ran Windows recently for a very long time. I upgraded to the 10.10 distribution and since that distro, it seems that for some reason all Linuxes want to push my laptop to extremes. I have recently upgraded to Ubuntu 12.04 since I heart that it contains kernel fixes for overheating issues. 12.04 will actually eventually cool the system, but that is after the fans run to the point it sounds like a jet aircraft taking off and the laptop makes my hands sweat. In trying to combat the heat problems I have done the following: I installed the propriatery driver for my ATI Mobility HD 3600. I have tried both the one in the Additional Drivers and also tried ATI's latest greatest version. If I don't install this my laptop will overheat and shut off in minutes. Both seem to perform similarly, but the heat problem remains. I have tried limiting the CPU by installing the CPUFreq Indicator. This does help keep the machine from shutting off, but the heat is still uncomfortable to be around the machine. I usually run in power saver mode or run the cpu at 1.6 GHZ just to error on safety. I ran sensors-detect and here are the results: sean@sean-Studio-1737:~$ sudo sensors-detect # sensors-detect revision 5984 (2011-07-10 21:22:53 +0200) # System: Dell Inc. Studio 1737 (laptop) # Board: Dell Inc. 0F237N This program will help you determine which kernel modules you need to load to use lm_sensors most effectively. It is generally safe and recommended to accept the default answers to all questions, unless you know what you're doing. Some south bridges, CPUs or memory controllers contain embedded sensors. Do you want to scan for them? This is totally safe. (YES/no): y Module cpuid loaded successfully. Silicon Integrated Systems SIS5595... No VIA VT82C686 Integrated Sensors... No VIA VT8231 Integrated Sensors... No AMD K8 thermal sensors... No AMD Family 10h thermal sensors... No AMD Family 11h thermal sensors... No AMD Family 12h and 14h thermal sensors... No AMD Family 15h thermal sensors... No AMD Family 15h power sensors... No Intel digital thermal sensor... Success! (driver `coretemp') Intel AMB FB-DIMM thermal sensor... No VIA C7 thermal sensor... No VIA Nano thermal sensor... No Some Super I/O chips contain embedded sensors. We have to write to standard I/O ports to probe them. This is usually safe. Do you want to scan for Super I/O sensors? (YES/no): y Probing for Super-I/O at 0x2e/0x2f Trying family `National Semiconductor/ITE'... No Trying family `SMSC'... No Trying family `VIA/Winbond/Nuvoton/Fintek'... No Trying family `ITE'... No Probing for Super-I/O at 0x4e/0x4f Trying family `National Semiconductor/ITE'... Yes Found `ITE IT8512E/F/G Super IO' (but not activated) Some hardware monitoring chips are accessible through the ISA I/O ports. We have to write to arbitrary I/O ports to probe them. This is usually safe though. Yes, you do have ISA I/O ports even if you do not have any ISA slots! Do you want to scan the ISA I/O ports? (YES/no): y Probing for `National Semiconductor LM78' at 0x290... No Probing for `National Semiconductor LM79' at 0x290... No Probing for `Winbond W83781D' at 0x290... No Probing for `Winbond W83782D' at 0x290... No Lastly, we can probe the I2C/SMBus adapters for connected hardware monitoring devices. This is the most risky part, and while it works reasonably well on most systems, it has been reported to cause trouble on some systems. Do you want to probe the I2C/SMBus adapters now? (YES/no): y Using driver `i2c-i801' for device 0000:00:1f.3: Intel ICH9 Module i2c-i801 loaded successfully. Module i2c-dev loaded successfully. Now follows a summary of the probes I have just done. Just press ENTER to continue: Driver `coretemp': * Chip `Intel digital thermal sensor' (confidence: 9) To load everything that is needed, add this to /etc/modules: #----cut here---- # Chip drivers coretemp #----cut here---- If you have some drivers built into your kernel, the list above will contain too many modules. Skip the appropriate ones! Do you want to add these lines automatically to /etc/modules? (yes/NO)y Successful! Monitoring programs won't work until the needed modules are loaded. You may want to run 'service module-init-tools start' to load them. Unloading i2c-dev... OK Unloading i2c-i801... OK Unloading cpuid... OK sean@sean-Studio-1737:~$ sudo service module-init-tools start module-init-tools stop/waiting I also tried installing i8k but that didn't work since it didn't seem to be able to communicate with the hardware (probably for different kind of device). Also I ran acpi -V and here are the results: Battery 0: Full, 100% Battery 0: design capacity 613 mAh, last full capacity 260 mAh = 42% Adapter 0: on-line Thermal 0: ok, 49.0 degrees C Thermal 0: trip point 0 switches to mode critical at temperature 100.0 degrees C Thermal 1: ok, 48.0 degrees C Thermal 1: trip point 0 switches to mode critical at temperature 100.0 degrees C Thermal 2: ok, 51.0 degrees C Thermal 2: trip point 0 switches to mode critical at temperature 100.0 degrees C Cooling 0: LCD 0 of 15 Cooling 1: Processor 0 of 10 Cooling 2: Processor 0 of 10 I have hit a wall and don't know what to do now. Any advice is appreciated.

    Read the article

  • Profiling Startup Of VS2012 &ndash; SpeedTrace Profiler

    - by Alois Kraus
    SpeedTrace is a relatively unknown profiler made a company called Ipcas. A single professional license does cost 449€+VAT. For the test I did use SpeedTrace 4.5 which is currently Beta. Although it is cheaper than dotTrace it has by far the most options to influence how profiling does work. First you need to create a tracing project which does configure tracing for one process type. You can start the application directly from the profiler or (much more interesting) it does attach to a specific process when it is started. For this you need to check “Trace the specified …” radio button and enter the process name in the “Process Name of the Trace” edit box. You can even selectively enable tracing for processes with a specific command line. Then you need to activate the trace project by pressing the Activate Project button and you are ready to start VS as usual. If you want to profile the next 10 VS instances that you start you can set the Number of Processes counter to e.g. 10. This is immensely helpful if you are trying to profile only the next 5 started processes. As you can see there are many more tabs which do allow to influence tracing in a much more sophisticated way. SpeedTrace is the only profiler which does not rely entirely on the profiling Api of .NET. Instead it does modify the IL code (instrumentation on the fly) to write tracing information to disc which can later be analyzed. This approach is not only very fast but it does give you unprecedented analysis capabilities. Once the traces are collected they do show up in your workspace where you can open the trace viewer. I do skip the other windows because this view is by far the most useful one. You can sort the methods not only by Wall Clock time but also by CPU consumption and wait time which none of the other products support in their views at the same time. If you want to optimize for CPU consumption sort by CPU time. If you want to find out where most time is spent you need Clock Total time and Clock Waiting. There you can directly see if the method did take long because it did wait on something or it did really execute stuff that did take so long. Once you have found a method you want to drill deeper you can double click on a method to get to the Caller/Callee view which is similar to the JetBrains Method Grid view. But this time you do see much more. In the middle is the clicked method. Above are the methods that call you and below are the methods that you do directly call. Normally you would then start digging deeper to find the end of the chain where the slow method worth optimizing is located. But there is a shortcut. You can press the magic   button to calculate the aggregation of all called methods. This is displayed in the lower left window where you can see each method call and how long it did take. There you can also sort to see if this call stack does only contain methods (e.g. WCF connect calls which you cannot make faster) not worth optimizing. YourKit has a similar feature where it is called Callees List. In the Functions tab you have in the context menu also many other useful analysis options One really outstanding feature is the View Call History Drilldown. When you select this one you get not a sum of all method invocations but a list with the duration of each method call. This is not surprising since SpeedTrace does use tracing to get its timings. There you can get many useful graphs how this method did behave over time. Did it become slower at some point in time or was only the first call slow? The diagrams and the list will tell you that. That is all fine but what should I do when one method call was slow? I want to see from where it was coming from. No problem select the method in the list hit F10 and you get the call stack. This is a life saver if you e.g. search for serialization problems. Today Serializers are used everywhere. You want to find out from where the 5s XmlSerializer.Deserialize call did come from? Hit F10 and you get the call stack which did invoke the 5s Deserialize call. The CPU timeline tab is also useful to find out where long pauses or excessive CPU consumption did happen. Click in the graph to get the Thread Stacks window where you can get a quick overview what all threads were doing at this time. This does look like the Stack Traces feature in YourKit. Only this time you get the last called method first which helps to quickly see what all threads were executing at this moment. YourKit does generate a rather long list which can be hard to go through when you have many threads. The thread list in the middle does not give you call stacks or anything like that but you see which methods were found most often executing code by the profiler which is a good indication for methods consuming most CPU time. This does sound too good to be true? I have not told you the best part yet. The best thing about this profiler is the staff behind it. When I do see a crash or some other odd behavior I send a mail to Ipcas and I do get usually the next day a mail that the problem has been fixed and a download link to the new version. The guys at Ipcas are even so helpful to log in to your machine via a Citrix Client to help you to get started profiling your actual application you want to profile. After a 2h telco I was converted from a hater to a believer of this tool. The fast response time might also have something to do with the fact that they are actively working on 4.5 to get out of the door. But still the support is by far the best I have encountered so far. The only downside is that you should instrument your assemblies including the .NET Framework to get most accurate numbers. You can profile without doing it but then you will see very high JIT times in your process which can severely affect the correctness of the measured timings. If you do not care about exact numbers you can also enable in the main UI in the Data Trace tab logging of method arguments of primitive types. If you need to know what files at which times were opened by your application you can find it out without a debugger. Since SpeedTrace does read huge trace files in its reader you should perhaps use a 64 bit machine to be able to analyze bigger traces as well. The memory consumption of the trace reader is too high for my taste. But they did promise for the next version to come up with something much improved.

    Read the article

  • Issues configuring Exchange 2010 as well as SSL problems.

    - by Eric Smith
    Possibly-Relevant Background Info: I've recently moved up from icky shared hosting to a glorious, Remote Desktop-administrated VPS server running Windows Server 2008 R2. Even though I'm only 21 now and a computer science major, I've tried to play with every Windows Server release since '03, just to learn new things. What usually happens is inevitably I'll do something wrong and pretty much ruin the install. You're dealing with an amateur here :) Through the past few months of working with my new server, I've mastered DNS, IIS, got Team Foundation Server running (yay!), and can install all of the other basics like SQL Server and Active Directory. The Problem: Now, these last few weeks I've been trying to install Exchange Server 2010 (SP1). To make a long story short, it took me several attempts, and I even had to get my server wiped just so I could start fresh since Exchange decided uninstalling properly was for sissies (cost me $20, bah). Today, at long last, I got Exchange mostly working. There were two main problems left, however, that left me unsatisfied: Exchange installed itself and all of its child sites into Default Web Site. I wanted to access Exchange via mail.domain.com, but instead everything was configured to domain.com. My limited server admin knowledge was not enough to configure IIS or Exchange to move itself over to the website I had set up for it, appropriately titled 'mail.domain.com', which I had bound to a dedicated IP address (I was told this was necessary, but he may have been wrong). I have two SSL certificates: one for my main domain and one for my mail subdomain. For whatever reason, I had issues geting Exchange to use my mail certificate, even though I had assigned the proper roles in the MMC. I did, at one point, get it to work (or mostly work, anyways. Frankly, my memory of today is clouded by intense frustration). Additionally, I was confused which type of SSL certificate I should be using for Exchange. My SSL provider, GoDaddy, allows me to request a new certificate whenever, so I can use either the certificate request provided by IIS or the more complicated and specific request you can create with Exchange. Which type should I be using, the IIS or Exchange certificate? If I must use the Exchange certificate, will that 1) cause issues when I bind that certificate to my mail.domain.com subdomain or 2) is that an unnecessary step? The SSL Certificate Strikes Back When I thought I had the proper SSL certificate assigned for those brief, sweet moments, Google Chrome reported the correct mail.domain.com certificate when browsing https://mail.domain.com. However, Outlook 2010 threw up an error when trying to configure my email account claiming that the certificate didn't match the domain of "mail.domain.com". Is this an issue that will be resolved by problem #2 or is it a separate one entirely? Apologies for the massive wall of text, but I wanted to provide as much info as I possibly could. Exchange is the last thing I'd like installed on my server, and naturally it's turning out to be the hardest. Thanks for any info at all. Even a point in a vague direction would be a huge help at this point. Thanks! -Eric P.S.: The reason I keep ruining my install is that when I attempt to uninstall Exchange, something invariably goes wrong. The last time the uninstaller complained that there was still a mailbox active and it couldn't proceed until I deleted it. ... The only mailbox left was the Administrator account, the built-in one I couldn't delete. So I attempted to manually uninstall it following several guides online only to now be stuck unable to launch the installer and have to get my system wiped AGAIN for the second time today ($40 down the drain, bah!). I do not understand at all why "uninstall" just can't mean "hey, you, delete everything and go away". There's not even a force uninstall option, only a "recover system" option that just fails to fix anything and makes it so I can't even use the GUI uninstaller. </rant>

    Read the article

  • A star algorithm implementation problems

    - by bryan226
    I’m having some trouble implementing the A* algorithm in a 2D tile based game. The problem is basically that the algorithm gets stuck when something gets in its direct way (e.g. walls) Note that it only allows Horizontal and Vertical movement. Here's a picture as it works fine across the map without something in its direct way: (Green tile = destination, Blue = In closed list, Green = in open list) This is what happens if I try to walk 'around' a wall: I calculate costs with the F = G + H formula: G = 1 Cost per Step H = 10 Cost per Step //Count how many tiles are between current-tile & destination-tile The functions: short c_astar::GuessH(short Startx,short Starty,short Destinationx,short Destinationy) { hgeVector Start, Destination; Start.x = Startx; Start.y = Starty; Destination.x = Destinationx; Destination.y = Destinationy; short a = 0; short b = 0; if(Start.x > Destination.x) a = Start.x - Destination.x; else a = Destination.x - Start.x; if(Start.y > Destination.y) b = Start.y - Destination.y; else b = Destination.y - Start.y; return (a+b)*10; } short c_astar::GuessG(short Startx,short Starty,short Currentx,short Currenty) { hgeVector Start, Destination; Start.x = Startx; Start.y = Starty; Destination.x = Currentx; Destination.y = Currenty; short a = 0; short b = 0; if(Start.x > Destination.x) a = Start.x - Destination.x; else a = Destination.x - Start.x; if(Start.y > Destination.y) b = Start.y - Destination.y; else b = Destination.y - Start.y; return (a+b); } At the end of the loop I check which tile is the cheapest to go according to its F value: Then some quick checks are done for each tile (UP,DOWN,LEFT,RIGHT): //...CX are holding the F value of the TILE specified // Info: C0 = Center (Current) // C1 = UP // C2 = DOWN // C3 = LEFT // C4 = RIGHT //Quick checks if(((C1 < C2) && (C1 < C3) && (C1 < C4))) { Current.y -= 1; bSimilar = false; if(DEBUG) hge->System_Log("C1 < ALL"); } //.. same for C2,C3 & C4 If there are multiple tiles with the same F value: It’s actually a switch for DOWNLEFT,UPRIGHT.. etc. Here’s one of it: case UPRIGHT: { //UP Temporary = Current; Temporary.y -= 1; bTileStatus[0] = IsTileWalkable(Temporary.x,Temporary.y); if(bTileStatus[0]) { //Proceed normal we are OK & walkable Tilex.Tile = map.at(Temporary.y).at(Temporary.x); //Search in lists if(SearchInClosedList(Tilex.Tile.ID,C0)) bFoundInClosedList[0] = true; if(SearchInOpenList(Tilex.Tile.ID,C0)) bFoundInOpenList[0] = true; //RIGHT Temporary = Current; Temporary.x += 1; bTileStatus[1] = IsTileWalkable(Temporary.x,Temporary.y); if(bTileStatus[1]) { //Proceed normal we are OK & walkable Tilex.Tile = map.at(Temporary.y).at(Temporary.x); //Search in lists if(SearchInClosedList(Tilex.Tile.ID,C0)) bFoundInClosedList[1] = true; if(SearchInOpenList(Tilex.Tile.ID,C0)) bFoundInOpenList[1] = true; //************************************************* // Purpose: ClosedList behavior //************************************************* if(bFoundInClosedList[0] && !bFoundInClosedList[1]) { //UP found in ClosedList. Go RIGHT return RIGHT; } if(!bFoundInClosedList[0] && bFoundInClosedList[1]) { //RIGHT found in ClosedList. Go UP return UP; } if(bFoundInClosedList[0] && bFoundInClosedList[1]) { //Both found in ClosedList. Random value switch(hge->Random_Int(8,9)) { case 8: return UP; break; case 9: return RIGHT; break; } } //************************************************* // Purpose: OpenList behavior //************************************************* if(bFoundInOpenList[0] && !bFoundInOpenList[1]) { //UP found in OpenList. Go RIGHT return RIGHT; } if(!bFoundInOpenList[0] && bFoundInOpenList[1]) { //RIGHT found in OpenList. Go UP return UP; } if(bFoundInOpenList[0] && bFoundInOpenList[1]) { //Both found in OpenList. Random value switch(hge->Random_Int(8,9)) { case 8: return UP; break; case 9: return RIGHT; break; } } } else if(!bTileStatus[1]) { //RIGHT is not walkable OR out of range //Choose UP return UP; } } else if(!bTileStatus[0]) { //UP is not walkable OR out of range //Fast check RIGHT Temporary = Current; Temporary.x += 1; bTileStatus[1] = IsTileWalkable(Temporary.x,Temporary.y); if(bTileStatus[1]) { return RIGHT; } else return FAILED; //Failed, no valid path found! } } break; A log for the second picture: (Cut down to ten passes, because it’s just repeating itself) ----------------------------------------------------- PASS: 1 | C1: 211 | C2: 191 | C3: 211 | C4: 191 DOWN + RIGHT SIMILAR Going DOWN ----------------------------------------------------- PASS: 2 | C1: 200 | C2: 182 | C3: 202 | C4: 182 DOWN + RIGHT SIMILAR Going DOWN ----------------------------------------------------- PASS: 3 | C1: 191 | C2: 193 | C3: 193 | C4: 173 C4 < ALL Tile(12.000000,6.000000) not walkable. MAX_F_VALUE set. ----------------------------------------------------- PASS: 4 | C1: 182 | C2: 184 | C3: 182 | C4: 999 UP + LEFT SIMILAR Going UP Tile(12.000000,5.000000) not walkable. MAX_F_VALUE set. ----------------------------------------------------- PASS: 5 | C1: 191 | C2: 173 | C3: 191 | C4: 999 C2 < ALL Tile(12.000000,6.000000) not walkable. MAX_F_VALUE set. ----------------------------------------------------- PASS: 6 | C1: 182 | C2: 184 | C3: 182 | C4: 999 UP + LEFT SIMILAR Going UP Tile(12.000000,5.000000) not walkable. MAX_F_VALUE set. ----------------------------------------------------- PASS: 7 | C1: 191 | C2: 173 | C3: 191 | C4: 999 C2 < ALL Tile(12.000000,6.000000) not walkable. MAX_F_VALUE set. ----------------------------------------------------- PASS: 8 | C1: 182 | C2: 184 | C3: 182 | C4: 999 UP + LEFT SIMILAR Going LEFT ----------------------------------------------------- PASS: 9 | C1: 191 | C2: 193 | C3: 193 | C4: 173 C4 < ALL Tile(12.000000,6.000000) not walkable. MAX_F_VALUE set. ----------------------------------------------------- PASS: 10 | C1: 182 | C2: 184 | C3: 182 | C4: 999 UP + LEFT SIMILAR Going LEFT ----------------------------------------------------- Its always going after the cheapest F value, which seems to be wrong. If someone could point me to the right direction I'd be thankful. Regards, bryan226

    Read the article

  • CodePlex Daily Summary for Monday, August 18, 2014

    CodePlex Daily Summary for Monday, August 18, 2014Popular ReleasesMagick.NET: Magick.NET 7.0.0.0001: Magick.NET linked with ImageMagick 7-Beta.CMake Tools for Visual Studio: CMake Tools for Visual Studio 1.2: This release adds the following new features and bug fixes from CMake Tools for Visual Studio 1.1: Added support for CMake 3.0. Added support for word completion. Added IntelliSense support for the CMAKEHOSTSYSTEM_INFORMATION command. Fixed syntax highlighting for tokens beginning with escape sequences. Fixed issue uninstalling CMake Tools for Visual Studio after Visual Studio has been uninstalled.GW2 Personal Assistant Overlay: GW2 Personal Assistant Overlay 1.1: Overview1.1 is the second 'stable' release of the GW2 Personal Assistant Overlay. This version includes just a couple of very minor features and some minor bug fixes. For details regarding installation, setup, and general use, see Documentation. Note: If you were using a previous version, you will probably want to copy over the following user settings files: GW2PAO.DungeonSettings.xml GW2PAO.EventSettings.xml GW2PAO.WvWSettings.xml GW2PAO.ZoneCompletionSettings.xml New FeaturesAdded new "No...WallSwitch: WallSwitch 1.2.5: Version 1.2.5 Changes: Added support for sequential order in collage mode. Added option to display multiple images per switch in collage mode. Fixed bug where border width wasn't being loaded properly, and was reverting to default values. Fixed bug where sequential order was repeating images on multiple monitors. Decreased likelihood of random images being repeated.OpenCppCoverage: OpenCppCoverage 0.9.1: - Add Jenkins support. - Command line argument can be placed inside a config file. If you do not have Visual Studio C++ 2013 you need to download redistributable packages: http://www.microsoft.com/en-us/download/details.aspx?id=40784Easy Backup Windows Service: Release 2.0 with CU: Fix log error when "To" directory not exist in fyle system. Force run program as administrator by default. Add 'everyday' schedule element. Update solution to VS 2013.Easy Backup Application: Release 2.0 with CU: Fix log error when "To" directory not exist in fyle system. Fix app location initialization. Force run program as administrator by default. Update solution to VS 2013.TEBookConverter: 1.5: Added: Turkish and French translations Added: A few interface changes Removed: SkinDynamulet: Dynamulet v0.1: DynamoDB Transaction Server v0.1Console parallel nunit tests runner: ConsoleUnitTestsRunner 1.03: bugfixingFluentx: Fluentx v1.5.3: Added few more extension methods.fastJSON: v2.1.2: 2.1.2 - bug fix circular referencesJPush.NET: JPush Server SDK 1.2.1 (For JPush V3): Assembly: 1.2.1.24728 JPush REST API Version: v3 JPush Documentation Reference .NET framework: v4.0 or above. Sample: class: JPushClientV3 2014 Augest 15th.SEToolbox: SEToolbox 01.043.008 Release 1: Changed ship/station names to use new DisplayName instead of Beacon/Antenna. Fixed issue with updated SE binaries 01.043.018 using new Voxel Material definitions.Google .Net API: Drive.Sample: Google .NET Client API – Drive.SampleInstructions for the Google .NET Client API – Drive.Sample</h2> http://code.google.com/p/google-api-dotnet-client/source/browse/?repo=samples#hg%2FDrive.SampleBrowse Source, or main file http://code.google.com/p/google-api-dotnet-client/source/browse/Drive.Sample/Program.cs?repo=samplesProgram.cs <h3>1. Checkout Instructions</h3> <p><b>Prerequisites:</b> Install Visual Studio, and <a href="http://mercurial.selenic.com/">Mercurial</a>.</p> ...FineUI - jQuery / ExtJS based ASP.NET Controls: FineUI v4.1.1: -??Form??????????????(???-5929)。 -?TemplateField??ExpandOnDoubleClick、ExpandOnEnter、ExpandToSelectRow????(LZOM-5932)。 -BodyPadding???????,??“5”“5 10”,???????????“5px”“5px 10px”。 -??TriggerBox?EnableEdit=false????,??????????????(Jango_Jing-5450)。 -???????????DataKeyNames???????????(yygy-6002)。 -????????????????????????(Gnid-6018)。 -??PageManager???AutoSizePanelID????,??????????????????(yygy-6008)。 -?FState???????????????,????????????????(????-5925)。 -??????OnClientClick???return?????????(FineU...DNN CMS Platform: 07.03.02: Major Highlights Fixed backwards compatibility issue with 3rd party control panels Fixed issue in the drag and drop functionality of the File Uploader in IE 11 and Safari Fixed issue where users were able to create pages with the same name Fixed issue that affected older versions of DNN that do not include the maxAllowedContentLength during upgrade Fixed issue that stopped some skins from being upgraded to newer versions Fixed issue that randomly showed an unexpected error during us...WordMat: WordMat for Mac: WordMat for Mac has a few limitations compared to the Windows version - Graph is not supported (Gnuplot, GeoGebra and Excel works) - Units are not supported yet (Coming up) The Mac version is yet as tested as the windows version.MFCMAPI: August 2014 Release: Build: 15.0.0.1042 Full release notes at SGriffin's blog. If you just want to run the MFCMAPI or MrMAPI, get the executables. If you want to debug them, get the symbol files and the source. The 64 bit builds will only work on a machine with Outlook 2010/2013 64 bit installed. All other machines should use the 32 bit builds, regardless of the operating system. Facebook BadgeEWSEditor: EwsEditor 1.10 Release: • Export and import of items as a full fidelity steam works - without proxy classes! - I used raw EWS POSTs. • Turned off word wrap for EWS request field in EWS POST windows. • Several windows with scrolling texts boxes were limiting content to 32k - I removed this restriction. • Split server timezone info off to separate menu item from the timezone info windows so that the timezone info window could be used without logging into a mailbox. • Lots of updates to the TimeZone window. • UserAgen...New Projectsballmon: ballmonExchange Database Recovery With and Without Log Files is Possible: This segments giving an overview of Exchange Server transaction log files. It describes process how users can recover their database with & without log filesFabs.Net: Ego tatmini ve gelisme amaçli yaptigim bir projedir.JacoChat: JacoChat is a simple chatting interface that uses my personal webserver as a "wall" for people to chat on.ManagedWin32: ManagedWin32 is a library that exposes the Win32 API to .NET applications.Open XML Extensions: The project provides additions to the Open XML SDK and related projects (e.g., PowerTools for Open XML), starting with MemoryStreams for Open XML Documents.orntic: Project for insurace companyTBOX: The Treasure Box Library: TBOX is a mutli-platform c library for unix, windows, mac, ios, android, etc. It includes asio, stream, container, algorithm, xml and other library modules.WeatherTS: Typescript weather application.?????@/????: ??????????????:????,????,????,???????,????????,??????:????????,?????! ?????????: ????????????????????,????????:??、??、???,?????????????????????! ????-??: ??????????????,????,???????????????。

    Read the article

  • How to begin? Windows 8 Development

    - by Dennis Vroegop
    Ok. I convinced you in my last post to do some Win8 development. You want a piece of that cake, or whatever your reasons may be. Good! Welcome to the club! Now let me ask you a question: what are you going to write? Ah. That’s the big one, isn’t it? What indeed? If you have been creating applications for computers before you’re in for quite a shock. The way people perceive apps on a tablet is quite different from what we know as applications. There’s a reason we call them apps instead of applications! Yes, technically they are applications but we don’t call them apps only because it sounds cool. The abbreviated form of the word applications itself is a pointer. Apps are small. Apps are focused. Apps are more lightweight. Apps do one thing but they do that one thing extremely good. In the ‘old’ days we wrote huge systems. We build ecosystems of services, screens, databases and more to create a system that provides value for the user. Think about it: what application do you use most at work? Can you in one sentence describe what it is, or what it does and yet still distinctively describe its purpose? I doubt you can. Let’s have a look at Outlouk. We all know it and we all love or hate it. But what is it? A mail program? No, there’s so much more there: calendar, contacts, RSS feeds and so on. Some call it a ‘collaboration’  application but that’s not really true as well. After all, why should a collaboration application give me my schedule for the day? I think the best way to describe Outlook is “client for Exchange”  although that isn’t accurate either. Anyway: Outlook is a great application but it’s not an ‘app’ and therefor not very suitable for WinRT. Ok. Disclaimer here: yes, you can write big applications for WinRT. Some will. But that’s not what 99.9% of the developers will do. So I am stating here that big applications are not meant for WinRT. If 0.01% of the developers think that this is nonsense then they are welcome to go ahead but for the majority here this is not what we’re talking about. So: Apps are small, lightweight and good at what they do but only at that. If you’re a Phone developer you already know that: Phone apps on any platform fit the description I have above. If you’ve ever worked in a large cooperation before you might have seen one of these before: the Mission Statement. It’s supposed to be a oneliner that sums up what the company is supposed to do. Funny enough: although this doesn’t work for large companies it does work for defining your app. A mission statement for an app describes what it does. If it doesn’t fit in the mission statement then your app is going to get to big and will fail. A statement like this should be in the following style “<your app name> is the best app to <describe single task>” Fill in the blanks, write it and go! Mmm.. not really. There are some things there we need to think about. But the statement is a very, very important one. If you cannot fit your app in that line you’re preparing to fail. Your app will become to big, its purpose will be unclear and it will be hard to use. People won’t download it and those who do will give it a bad rating therefor preventing that huge success you’ve been dreaming about. Stick to the statement! Ok, let’s give it a try: “PlanesAreCool” is the best app to do planespotting in the field. You might have seen these people along runways of airports: taking photographs of airplanes and noting down their numbers and arrival- and departure times. We are going to help them out with our great app! If you look at the statement, can you guess what it does? I bet you can. If you find out it isn’t clear enough of if it’s too broad, refine it. This is probably the most important step in the development of your app so give it enough time! So. We’ve got the statement. Print it out, stick it to the wall and look at it. What does it tell you? If you see this, what do you think the app does? Write that down. Sit down with some friends and talk about it. What do they expect from an app like this? Write that down as well. Brainstorm. Make a list of features. This is mine: Note planes Look up aircraft carriers Add pictures of that plane Look up airfields Notify friends of new spots Look up details of a type of plane Plot a graph with arrival and departure times Share new spots on social media Look up history of a particular aircraft Compare your spots with friends Write down arrival times Write down departure times Write down wind conditions Write down the runway they take Look up weather conditions for next spotting day Invite friends to join you for a day of spotting. Now, I must make it clear that I am not a planespotter nor do I know what one does. So if the above list makes no sense, I apologize. There is a lesson: write apps for stuff you know about…. First of all, let’s look at our statement and then go through the list of features. Remove everything that has nothing to do with that statement! If you end up with an empty list, try again with both steps. Note planes Look up aircraft carriers Add pictures of that plane Look up airfields Notify friends of new spots Look up details of a type of plane Plot a graph with arrival and departure times Share new spots on social media Look up history of a particular aircraft Compare your spots with friends Write down arrival times Write down departure times Write down wind conditions Write down the runway they take Look up weather conditions for next spotting day Invite friends to join you for a day of spotting. That's better. The things I removed could be pretty useful to a plane spotter and could be fun to write. But do they match the statement? I said that the app is for spotting in the field, so “look up airfields” doesn’t belong there: I know where I am so why look it up? And the same goes for inviting friends or looking up the weather conditions for tomorrow. I am at the airfield right now, looking through my binoculars at the planes. I know the weather now and I don’t care about tomorrow. If you feel the items you’ve crossed out are valuable, then why not write another app? One that says “SpotNoter” is the best app for preparing a day of spotting with my friends. That’s a different app! Remember: Win8 apps are small and very good at doing ONE thing, and one thing only! If you have made that list, it’s time to prepare the navigation of your app. The navigation is how users see your app and how they use it. We’ll do that next time!

    Read the article

  • Adventures in Windows 8: Working around the navigation animation issues in LayoutAwarePage

    - by Laurent Bugnion
    LayoutAwarePage is a pretty cool add-on to Windows 8 apps, which facilitates greatly the implementation of orientation-aware (portrait, landscape) as well as state-aware (snapped, filled, fullscreen) apps. It has however a few issues that are obvious when you use transformed elements on your page. Adding a LayoutAwarePage to your application If you start with a blank app, the MainPage is a vanilla Page, with no such feature. In order to have a LayoutAwarePage into your app, you need to add this class (and a few helpers) with the following operation: Right click on the Solution and select Add, New Item from the context menu. From the dialog, select a Basic Page (not a Blank Page, which is another vanilla page). If you prefer, you can also use Split Page, Items Page, Item Detail Page, Grouped Items Page or Group Detail Page which are all LayoutAwarePages. Personally I like to start with a Basic Page, which gives me more creative freedom. Adding this new page will cause Visual Studio to show a prompt asking you for permission to add additional helper files to the Common folder. One of these helpers in the LayoutAwarePage class, which is where the magic happens. LayoutAwarePage offers some help for the detection of orientation and state (which makes it a pleasure to design for all these scenarios in Blend, by the way) as well as storage for the navigation state (more about that in a future article). Issue with LayoutAwarePage When you use UI elements such as a background picture, a watermark label, logos, etc, it is quite common to do a few things with those: Making them partially transparent (this is especially true for background pictures; for instance I really like a black Page background with a half transparent picture placed on top of it). Transforming them, for instance rotating them a bit, scaling them, etc. Here is an example with a picture of my two beautiful daughters in the Bird Park in Kuala Lumpur, as well as a transformed TextBlock. The image has an opacity of 40% and the TextBlock a simple RotateTransform. If I create an application with a MainPage that navigates to this LayoutAwarePage, however, I will have a very annoying effect: The background picture appears with an Opacity of 100%. The TextBlock is not rotated. This lasts only for less than a second (during the navigation animation) before the elements “snap into place” and get their desired effect. Here is the XAML that cause the annoying effect: <common:LayoutAwarePage x:Name="pageRoot" x:Class="App13.BasicPage1" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:common="using:App13.Common" xmlns:d="http://schemas.microsoft.com/expression/blend/2008" xmlns:mc="http://schemas.openxmlformats.org/markup-compatibility/2006" mc:Ignorable="d"> <Grid Style="{StaticResource LayoutRootStyle}"> <Grid.RowDefinitions> <RowDefinition Height="140" /> <RowDefinition Height="*" /> </Grid.RowDefinitions> <Image Source="Assets/el20120812025.jpg" Stretch="UniformToFill" Opacity="0.4" Grid.RowSpan="2" /> <Grid> <Grid.ColumnDefinitions> <ColumnDefinition Width="Auto" /> <ColumnDefinition Width="*" /> </Grid.ColumnDefinitions> <Button x:Name="backButton" Click="GoBack" IsEnabled="{Binding Frame.CanGoBack, ElementName=pageRoot}" Style="{StaticResource BackButtonStyle}" /> <TextBlock x:Name="pageTitle" Grid.Column="1" Text="Welcome" Style="{StaticResource PageHeaderTextStyle}" /> </Grid> <TextBlock HorizontalAlignment="Center" TextWrapping="Wrap" Text="Welcome to my Windows 8 Application" Grid.Row="1" VerticalAlignment="Bottom" FontFamily="Segoe UI Light" FontSize="70" FontWeight="Light" TextAlignment="Center" Foreground="#FFFFA200" RenderTransformOrigin="0.5,0.5" UseLayoutRounding="False" d:LayoutRounding="Auto" Margin="0,0,0,153"> <TextBlock.RenderTransform> <CompositeTransform Rotation="-6.545" /> </TextBlock.RenderTransform> </TextBlock> <VisualStateManager.VisualStateGroups> [...] </VisualStateManager.VisualStateGroups> </Grid> </common:LayoutAwarePage> Solving the issue In order to solve this “snapping” issue, the solution is to wrap the elements that are transformed into an empty Grid. Honestly, to me it sounds like a bug in the LayoutAwarePage navigation animation, but thankfully the workaround is not that difficult: Simple change the main Grid as follows: <Grid Style="{StaticResource LayoutRootStyle}"> <Grid.RowDefinitions> <RowDefinition Height="140" /> <RowDefinition Height="*" /> </Grid.RowDefinitions> <Grid Grid.RowSpan="2"> <Image Source="Assets/el20120812025.jpg" Stretch="UniformToFill" Opacity="0.4" /> </Grid> <Grid> <Grid.ColumnDefinitions> <ColumnDefinition Width="Auto" /> <ColumnDefinition Width="*" /> </Grid.ColumnDefinitions> <Button x:Name="backButton" Click="GoBack" IsEnabled="{Binding Frame.CanGoBack, ElementName=pageRoot}" Style="{StaticResource BackButtonStyle}" /> <TextBlock x:Name="pageTitle" Grid.Column="1" Text="Welcome" Style="{StaticResource PageHeaderTextStyle}" /> </Grid> <Grid Grid.Row="1"> <TextBlock HorizontalAlignment="Center" TextWrapping="Wrap" Text="Welcome to my Windows 8 Application" VerticalAlignment="Bottom" FontFamily="Segoe UI Light" FontSize="70" FontWeight="Light" TextAlignment="Center" Foreground="#FFFFA200" RenderTransformOrigin="0.5,0.5" UseLayoutRounding="False" d:LayoutRounding="Auto" Margin="0,0,0,153"> <TextBlock.RenderTransform> <CompositeTransform Rotation="-6.545" /> </TextBlock.RenderTransform> </TextBlock> </Grid> <VisualStateManager.VisualStateGroups> [...] </Grid> Hopefully this will help a few people, I banged my head on the wall for a while before someone at Microsoft pointed me to the solution ;) Happy coding, Laurent   Laurent Bugnion (GalaSoft) Subscribe | Twitter | Facebook | Flickr | LinkedIn

    Read the article

  • I'm a contract developer and I think I'm about to get screwed [closed]

    - by kagaku
    I do contract development on the side. You could say that I'm a contract developer? Considering I've only ever had one client I'd say that's not exactly the truth - more like I took a side job and needed some extra cash. It started out as a "rebuild our website and we'll pay you $10k" type project. Once that was complete (a bit over schedule, but certainly not over budget), the company hired me on as a "long term support" contractor. The contract is to go from March of this year, expiring on December 31st of this year - 10 months. Over which a payment is to be paid on the 30th of each month for a set amount. I've been fulfilling my end of the contract on all points - doing server maintenence, application and database changes, doing huge rush changes and pretty much just going above and beyond. Currently I'm in the middle of development of an iPhone mobile application (PhoneGap based) which is nearing completion (probably 3-4 weeks from submission). It has not been all peaches and flowers though. Each and every month when my paycheck comes due, there always seems to be an issue of sorts. These issues did not occur during the initial project, only during the support contract. The actual contract states that my check should be mailed out on the 30th of the month. I have received my check on time approximately once (on time being about 2-3 days within the 30th). I've received my paycheck as late as the 15th of the next month - over two weeks late. I've put up with it because I need the paycheck. There have been promises and promises of "we'll send it out on time next time! I promise" - only to receive it just as late the next month. When I ask about payment they give me a vibe like "why are you only worried about money?" - unfortunately I don't have the luxury of not worrying about money. The last straw was with my August payment, which should have been mailed on August 30th. I received it on September 12th. The reason for the delay? "USPS is delaying it man! we sent it out on the 1st!" is the reason I got. When I finally got the check in the mail, the postage on the envelope was marked September 10th - the date it was run through the postage machine. I've been outright lied to, at this point. I carry on working, because again - I need a paycheck. I orchestrated the move of our application to a new server, developed a bunch of new changes and continued work on the iPhone app. All told I probably went over my hourly allotment (I'm paid for 40 hours a month, I probably put in at least 50). On Saturday, the 1st, I gave the main contact at the company (a company of 3, by the way - this is not some big corporation) a ring and filled him in on the status of my work for the past two weeks. Unusually I hadn't heard from him since the middle of September. His response was "oh... well, that is nice and uh.. good job. well, we've been talking within the company about things and we've certainly got some decisions ahead of us..." - not verbatim but you get the idea (I hope?). I got out of this conversation that the site is not doing very well (which it's not) and they're considering pulling the plug. Crap, this contract is going to end early - there goes Christmas! Fine, that's alright, no problem. I'll get paid for the last months work and call it a day. Unfortunately I still haven't gotten last months check, and I'm getting dicked around now. "Oh.. we had problems transferring funds, we'll try and mail it out tomorrow" and "I left a VM with the finance guy, but I can't get ahold of him". So I'm getting the feeling I'm not getting paid for all the work I put in for September. This is obviously breach of contract, and I am pissed. Thinking irrationally, I considered changing all their passwords and holding their stuff hostage. Before I think it through (by the way, I am NOT going to do this, realized it would probably get me in trouble), I go and try some passwords for our various accounts. Google Apps? Oh, I'm no longer administrator here. Godaddy? Whoops, invalid password. Disqus? Nope, invalid password here too. Google Adsense / Analytics? Invalid password. Dedicated server account manager? Invalid password. Now, I have the servers root password - I just built the box last week and haven't had a chance to send the guy the root password. Wasn't in a rush, I manage the server and they never touch it. Now all of a sudden all the passwords except this one are changed; the writing is on the wall - I am out. Here's the conundrum. I have the root password, they do not. If I give them this password all the leverage I have is gone, out the door and out of my hands. During this argument of why am I not getting paid the guy sends me an email saying "oh by the way, what's the root username and password to the server?". Considering he knows absolutely nothing, I gave him an "admin" account which really has almost no rights. I still have exclusive access to the server, I just don't know where to go. I can hold their data hostage, but I'm almost positive this is the wrong thing to do. I'd consider it blackmail, regardless of whether or not I have gotten paid yet. I can "break" something on the server and give them the whole "well, if you were paying me I could fix it!" spiel. This works from a "well he's not holding their stuff hostage" point of view, but what stops them from hiring some one else to just fix the issue at hand? For all I know the guys nephew is a "l33t hax0r" and can figure it out for free. I can give in, document as much as I can and take him to small claims court. This is breach of contract, I'm not getting paid. I have a case, right? ???? Does anyone have any experience in this? What can I do? What are my options? I'm broke, I can't afford a lawyer and I can barely afford not getting this paycheck. My wife doesn't work (I work two jobs so she doesn't have to work - we have a 1 year old) and is already looking at getting a part time job to cover the bills. Long term we'll be fine, but this has pissed me off beyond belief! Help me out, I'm about to get screwed.

    Read the article

  • OpenVPN Error : TLS Error: local/remote TLS keys are out of sync: [AF_INET]

    - by Lucidity
    Fist off thanks for reading this, I appreciate any and all suggestions. I am having some serious problems reconnecting to my OpenVPN client using Riseup.net's VPN. I have spent a few days banging my head against the wall in attempts to set this up on my iOS devices....but that is a whole other issue. I was however able to set it up on my Mac OS X specifically on my Windows Vista 32 bit BootCamp VM with relatively little trouble. To originally connect I only had to modify the recommended Config file very slightly (Config file included at the end of this post): - I had to enter the code directly into my config file - And change "dev tap" to "dev tun" So I was connected. (Note - I did test to ensure the VPN was actually working after I originally connected, it was. Also verified the .pem file (inserted as the coding in my config file) for authenticity). I left the VPN running. My computer went to sleep. Today I went to use the internet expecting (possibly incorrectly - I am now unsure if I was wrong to leave it running) to still be connected to the VPN. However I saw immediately I was not. I went to reconnect. And was (am) unable to. My logs after attempting to connect (and getting a connection failed dialog box) show everything working as it should (as far as I can tell) until the end where I get the following lines: Mon Sep 23 21:07:49 2013 us=276809 Initialization Sequence Completed Mon Sep 23 21:07:49 2013 us=276809 MANAGEMENT: >STATE:1379995669,CONNECTED,SUCCESS, OMITTED Mon Sep 23 21:22:50 2013 us=390350 Authenticate/Decrypt packet error: packet HMAC authentication failed Mon Sep 23 21:23:39 2013 us=862180 TLS Error: local/remote TLS keys are out of sync: [AF_INET] VPN IP OMITTED [2] Mon Sep 23 21:23:57 2013 us=395183 Authenticate/Decrypt packet error: packet HMAC authentication failed Mon Sep 23 22:07:41 2013 us=296898 TLS: soft reset sec=0 bytes=513834601/0 pkts=708032/0 Mon Sep 23 22:07:41 2013 us=671299 VERIFY OK: depth=1, C=US, O=Riseup Networks, L=Seattle, ST=WA, CN=Riseup Networks, [email protected] Mon Sep 23 22:07:41 2013 us=671299 VERIFY OK: depth=0, C=US, O=Riseup Networks, L=Seattle, ST=WA, CN=vpn.riseup.net Mon Sep 23 22:07:46 2013 us=772508 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Mon Sep 23 22:07:46 2013 us=772508 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Mon Sep 23 22:07:46 2013 us=772508 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Mon Sep 23 22:07:46 2013 us=772508 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Mon Sep 23 22:07:46 2013 us=772508 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 2048 bit RSA So I have searched for a solution online and I have included what I have attempted below, however I fear (know) I am not knowledgeable enough in this area to fix this myself. I apologize in advance for my ignorance. I do tech support for a living, but not this kind of tech support unfortunately. Other notes and troubleshooting done - - Windows Firewall is disabled completely, as well as other Anti-virus programs - Tor is disabled completely - No Proxies running - Time is correct in all locations - Router Firmware is up to date - Able to connect to the internet and as far as I can tell all necessary ports are open. - No settings have been altered since I was able to connect successfully. - Ethernet as well as wifi connections attempted, resulted in same error. Also tried adding the following lines to my config file (without success or change in error): persist-key persist-tun proto tcp (after reading that this error generally occurs on UDP connections, and is extremely rare on TCP) resolv-retry infinite (thinking the connection may have timed out since the issues occurred after leaving VPN connected during about 10 hrs of computer in sleep mode) All attempts resulted in exact same error code included at the top of this post. The original suggestions I found online stated - (regarding the TLS Error) - This error should resolve itself within 60 seconds, or if not quit wait 120 seconds and try again. (Which isnt the case here...) (regarding the Out of Sync" error) - If you continue to get "out of sync" errors and the link does not come up, then it means that something is probably wrong with your config file. You must use either ping and ping-restart on both sides of the connection, or keepalive on the server side of a client/server connection, in order to gracefully recover from "local/remote TLS keys are out of sync" errors. I wouldn't be surprised if my config file is lacking, or not correct. However I can confirm I followed the instructions to a tee. And was able to connect originally (and have not modified my settings or config file since I was able to connect to when the error began occurring). I have a very simple config file: client dev tun tun-mtu 1500 remote vpn.riseup.net auth-user-pass ca RiseupCA.pem redirect-gateway verb 4 <ca> -----BEGIN CERTIFICATE----- [OMITTED] -----END CERTIFICATE----- </ca> I would really appreciate any help or suggestions. I am at a total loss here, I know I'm asking a lot here. Though I am a new user on this site I help others on many forums including Microsoft's support community and especially Apple's support communities, so I will definitely pass on anything I learn here to help others. Thanks so so so much in advance for reading this.

    Read the article

  • Need help diagnosing network performance issues

    - by tokes
    I am currently working in a developing country as a system analyst for a government department. My area of expertise is software projects, but I've come across a few issues with the network setup in my office. (Unfortunately, being a developing country, there's not a lot of professional help available for this sort of thing.) Most recently, I am trying to diagnose a problem with slowness on the network. Our office is connected to the internet via an ADSL wireless modem/router (called Router). The modem is connected via ethernet to a switch (called Switch). The modem also acts as a wireless access point (called Wireless1), though because it is in a room at the end of the floor, it's range is limited. There are ethernet ports installed around the office. The cables of these all lead back to the same switch. In closer vicinity to the bulk of the client computers, there is another wireless router that acts as an access point for those clients (called Wireless2). That router is connected via ethernet to a wall port, and therefore to Switch. There is also a Windows server which acts as a DNS server (called DNSBox) which is located in the same room and is connected directly to Switch. ---Internet----------| Router/Wireless1 192.168.10.1 ---------------| |----|=========| DNSBox | |-------------------- 192.168.10.4 --------------------| Switch |---Other clients---- | |-------------------- |----|=========| Wireless2 ------------------| 192.168.10.198 One final thing to mention about the network setup. All clients are configured with manual IP addresses. Their router/gateway is set to the IP address of Router, and their DNS server is set to the IP address of DNSBox (with a secondary IP set to an external IP - that of our ISP's DNS server). Here are the symptoms we are experiencing: Clients connected to Wireless2 AP experience slow and unstable connections to the internet. (Slow here is defined as speeds of ~1KB/s, though ping response times seem to be as normal.) Clients connected via ethernet to Switch also experience the same slowness. Clients connected to Wireless1 AP (i.e. connecting via wireless directly to the ADSL modem) experience normal connections to the internet. Clients connected via ethernet to Router (i.e. connecting via ethernet directly to the ADSL modem) also experience normal connections to the internet. I also tried to gauge the connection performance between two machines on the network via ethernet: A file transfer between two clients who were both directly connected to Switch was the fastest; A file transfer between one client directly connected to Switch, and one client directly connected to Router (which is directly connected to Switch) performed much slower; A file transfer between two clients directly connected to Router also performed slowly. Things I have attempted to diagnose the problem: Restarted Switch -- no change. We tried unplugging ethernet jacks from Switch 4 at a time and testing the internet connection. The thought here was that perhaps a client on the network has contracted a virus, and is possibly spamming the network with traffic? (Not very technical, I know.) Unfortunately we couldn't get any significant increases in performance using this method. There were a couple of times when it seemed to be better, but then the connection speed quickly dropped back to slow/dead pace. I didn't want to unplug all jacks from Switch because I was concerned that users might be affected or that I would re-plug in the jacks incorrectly (should I even be worried about that? a port is a port on a switch, right?) I tried swapping the ethernet cable used to connect Router to Switch -- no change in performance. I tried swapping the port used on Switch for Router -- no change in performance. Anyone got any ideas on what this could be? Should I be mentioning specific brand names/models of the hardware used? Virii outbreaks are common in this country/office -- what could I be doing to figure out if a virus is at fault? If it is a virus, it doesn't seem to be generating a lot of traffic to/from the internet, because a) I can still get a good speed if I am directly connected to Router / Wireless1 and b) our ISP data usage has not risen suspiciously. Thanks for your help! Update #1 Here are the specs of some of the hardware: Switch is an Edimax ES3132RL 32-Port 10/100 Rackmount Switch Router is a D-Link DSL-G604T Update #2 I just tried unplugging everything except a laptop and Router from Switch. Speeds are still slow. I guess that means that Router / Switch are not being flooded? It seems more and more likely that the cause is something to do with the interaction between Router and Switch. However, I still can't find any useful resources on setting the LAN speed for either (and I'm not well-versed in these advanced networking configurations).

    Read the article

  • All downloads being interrupted

    - by Jake
    System: Windows 7 Professional 64bit. 8GB RAM, Intel i5-2400 CPU, +300GB free on the hard drive. AVG Internet Security 2012 (enabled & disabled, with firewall enabled and disabled - no effect for either). This computer is less than a year old. Network: This problem is occurring on a single computer on a network with multiple computers. The router is a Motorola Netopia 3347-02 (DSL Modem/Wireless Router combined). The computer is plugged in directly to the modem, other computers are using the wireless successfully. The router has been reset. The only thing odd about the connection between the router and computer is that it is configured to allow RDP through, so it is assigned a static IP by the router and port forwarding is enabled for port 3389. Also, though I doubt it matters, a second wireless router is active behind this router providing a second network that some computers in the area use without issues. Details: All downloads initiated on this specific computer eventually fail, this includes streaming from youtube, specialized downloads (itunes), downloads from websites, FTP downloads, etc. Failure occurs with all browsers, but in chrome this is the process it takes: 1) Download begins normally, 2) At some point between (observed) 7MBs and 229MBs the download stops progressing (at this point, if watching chrome's task manager, you can see the network activity for the downloading tab drop to 0kps), 3) for some time the download sits there still attempting to complete, but will eventually display "123,049,871/0 B, Interrupted" (where the number is whatever it actually got to). The file I am using to test this is a very large .zip file located on a server I control, but the problem seems to occur on any site. The amount downloaded is completely random, and seems to be more time-based than anything (if I start a download immediately after the last one fails, it tends to get further than the last one). Small files can get through for this reason, though they can fail as well. In a test where I simultaneously downloaded the same file via HTTP (chrome) and FTP (windows explorer), both downloads failed at the same instant, though explorer displayed "Connection timed out" several minutes before chrome finally showed the download as interrupted. Other things I have tried based on advice given to people with similar/identical problems: Setting my MTU to 1492 (as described here: http://blog.thecompwiz.com/2011/08/networking-issues.html) Disabling write caching to the hard drive storing the download on an external device successfully transmitted +1GB file from one computer on the same network to this computer disabling indexing in the folder the download was being stored in disabling all security software checked to make sure all drivers were up to date read about 50 accounts with nearly exact descriptions of what I'm experiencing, none of which had a solution given Running Processes: Image Name PID Session Name Session# Mem Usage ========================= ======== ================ =========== ============ System Idle Process 0 Services 0 24 K System 4 Services 0 104,836 K smss.exe 332 Services 0 1,276 K csrss.exe 764 Services 0 5,060 K wininit.exe 820 Services 0 4,748 K csrss.exe 844 Console 1 23,764 K services.exe 876 Services 0 11,856 K lsass.exe 892 Services 0 14,420 K lsm.exe 900 Services 0 7,820 K winlogon.exe 944 Console 1 7,716 K svchost.exe 428 Services 0 12,744 K svchost.exe 796 Services 0 12,240 K svchost.exe 1036 Services 0 22,372 K svchost.exe 1084 Services 0 174,132 K svchost.exe 1112 Services 0 56,144 K svchost.exe 1288 Services 0 18,640 K svchost.exe 1404 Services 0 29,616 K spoolsv.exe 1576 Services 0 25,924 K svchost.exe 1616 Services 0 12,788 K AppleMobileDeviceService. 1728 Services 0 9,796 K avgwdsvc.exe 1820 Services 0 8,268 K mDNSResponder.exe 1844 Services 0 5,832 K w3dbsmgr.exe 1108 Services 0 43,760 K QBCFMonitorService.exe 1336 Services 0 16,408 K svchost.exe 2404 Services 0 28,240 K taskhost.exe 3020 Console 1 12,372 K dwm.exe 2280 Console 1 5,968 K explorer.exe 2964 Console 1 152,476 K WUDFHost.exe 3316 Services 0 6,740 K svchost.exe 3408 Services 0 5,556 K RAVCpl64.exe 3684 Console 1 13,864 K igfxtray.exe 3700 Console 1 7,804 K hkcmd.exe 3772 Console 1 7,868 K igfxpers.exe 3788 Console 1 10,940 K sidebar.exe 3836 Console 1 84,400 K chrome.exe 3964 Console 1 19,640 K pptd40nt.exe 4068 Console 1 5,156 K acrotray.exe 3908 Console 1 14,676 K avgtray.exe 3872 Console 1 9,508 K jusched.exe 4076 Console 1 4,412 K iTunesHelper.exe 1532 Console 1 87,308 K SearchIndexer.exe 3492 Services 0 36,948 K iPodService.exe 4136 Services 0 7,944 K BrccMCtl.exe 4276 Console 1 18,132 K splwow64.exe 4380 Console 1 32,600 K qbupdate.exe 4836 Console 1 24,236 K svchost.exe 4288 Services 0 20,700 K wmpnetwk.exe 3112 Services 0 9,516 K FNPLicensingService.exe 5248 Services 0 5,852 K QBW32.EXE 5508 Console 1 127,068 K QBDBMgrN.exe 5600 Services 0 42,252 K EXCEL.EXE 2512 Console 1 99,100 K LMS.exe 3188 Services 0 5,616 K UNS.exe 1600 Services 0 7,308 K axlbridge.exe 5260 Console 1 5,132 K chrome.exe 5888 Console 1 200,336 K chrome.exe 3536 Console 1 26,076 K chrome.exe 1952 Console 1 20,168 K chrome.exe 4596 Console 1 24,696 K chrome.exe 4292 Console 1 48,096 K chrome.exe 2796 Console 1 23,520 K Acrobat.exe 1240 Console 1 87,252 K 123w.exe 4892 Console 1 22,728 K calc.exe 1700 Console 1 12,636 K chrome.exe 1328 Console 1 28,888 K chrome.exe 3696 Console 1 47,012 K rundll32.exe 6320 Console 1 7,104 K chrome.exe 4928 Console 1 44,248 K AVGIDSAgent.exe 260 Services 0 12,940 K avgfws.exe 6052 Services 0 26,912 K avgnsa.exe 5064 Services 0 2,496 K avgrsa.exe 3088 Services 0 2,200 K avgcsrva.exe 2596 Services 0 380 K avgcsrva.exe 6948 Services 0 408 K StikyNot.exe 452 Console 1 14,772 K chrome.exe 4580 Console 1 28,200 K chrome.exe 4016 Console 1 57,756 K svchost.exe 7140 Services 0 4,500 K chrome.exe 6264 Console 1 56,824 K chrome.exe 7008 Console 1 56,896 K chrome.exe 2224 Console 1 38,032 K taskhost.exe 612 Console 1 7,228 K chrome.exe 6000 Console 1 10,928 K chrome.exe 2568 Console 1 43,052 K chrome.exe 272 Console 1 75,988 K chrome.exe 7328 Console 1 53,240 K PaprPort.exe 7976 Console 1 137,152 K pplinks.exe 7500 Console 1 14,052 K ppscanmg.exe 5744 Console 1 18,996 K taskeng.exe 7388 Console 1 6,308 K SearchProtocolHost.exe 8024 Services 0 8,804 K SearchFilterHost.exe 7232 Services 0 7,848 K chrome.exe 8016 Console 1 37,440 K cmd.exe 7692 Console 1 3,096 K conhost.exe 7516 Console 1 5,872 K tasklist.exe 8160 Console 1 5,772 K WmiPrvSE.exe 7684 Services 0 6,400 K Any help with this would be greatly appreciated, I've been beating my head against a wall over this all day. This computer serves dual purpose as the main company document server and the Owner's work computer, it's fairly important it be fully functional and I cannot figure this out.

    Read the article

  • FFmpeg audio dont work in converted videos

    - by Juddy Swaft
    NOTICE: when i convert videos via terminal and download them from ftp into pc the audio works fine. I use: if($ext == "avi" && $convert_avi == true) { $convert_source = _VIDEOS_DIR_PATH.$new_name; $conv_name = substr(md5($file['name'].rand(1,888)), 2, 10).".mp4"; $converted_file = _VIDEOS_DIR_PATH.$conv_name; $ffmpeg_command = 'ffmpeg -i '.$convert_source.' -acodec libmp3lame -vcodec libx264 -s 1280x720 -ar 44100 -async 44100 -r 29.970 -ac 2 -qscale 5 '.$converted_file; echo exec($ffmpeg_command); $sql = "UPDATE pm_temp SET url = '".$conv_name."' WHERE url = '".$new_name."' LIMIT 1"; $result = @mysql_query($sql); unlink($convert_source); } This code to convert avi to mp4 ffmpeg concole output: root@1tb:~# ffmpeg -i sample.avi -acodec libmp3lame -vcodec libx264 -s 1280x720 -ar 44100 -async 44100 -r 29.970 -ac 2 -qscale 5 goodsample.mp4 ffmpeg version 0.7.15, Copyright (c) 2000-2013 the FFmpeg developers built on Feb 22 2013 07:18:58 with gcc 4.4.5 configuration: --enable-libdc1394 --prefix=/usr --extra-cflags='-Wall -g ' --cc='ccache cc' --enable-shared --enable-libmp3lame --enable-gpl --enable-libvorbis --enable-pthreads --enable-libfaac --enable-libxvid --enable-postproc --enable-x11grab --enable-libgsm --enable-libtheora --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-libx264 --enable-libspeex --enable-nonfree --disable-stripping --enable-avfilter --enable-libdirac --disable-decoder=libdirac --enable-libfreetype --enable-libschroedinger --disable-encoder=libschroedinger - s libavutil 50. 43. 0 / 50. 43. 0 libavcodec 52.123. 0 / 52.123. 0 libavformat 52.111. 0 / 52.111. 0 libavdevice 52. 5. 0 / 52. 5. 0 libavfilter 1. 80. 0 / 1. 80. 0 libswscale 0. 14. 1 / 0. 14. 1 libpostproc 51. 2. 0 / 51. 2. 0 [mp3 @ 0x191d4100] Header missing [mpeg4 @ 0x191d1dc0] Invalid and inefficient vfw-avi packed B frames detected Input #0, avi, from 'sample.avi': Metadata: encoder : VirtualDubMod 1.5.10.2 (build 2540/release) Duration: 00:01:01.81, start: 0.000000, bitrate: 1194 kb/s Stream #0.0: Video: mpeg4, yuv420p, 640x352 [PAR 1:1 DAR 20:11], 23.98 tbr, Stream #0.1: Audio: mp3, 48000 Hz, stereo, s16, 128 kb/s [buffer @ 0x191d1c80] w:640 h:352 pixfmt:yuv420p tb:1/1000000 sar:1/1 sws_param: [scale @ 0x191d6880] w:640 h:352 fmt:yuv420p -> w:1280 h:720 fmt:yuv420p flags:0 [libx264 @ 0x191ce5a0] Default settings detected, using medium profile [libx264 @ 0x191ce5a0] using SAR=45/44 [libx264 @ 0x191ce5a0] using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle S [libx264 @ 0x191ce5a0] profile High, level 3.1 [libx264 @ 0x191ce5a0] 264 - core 118 - H.264/MPEG-4 AVC codec - Copyleft 2003-2 6 chroma_me=1 trellis=1 8x8dct=1 cqm=0 deadzone=21,11 fast_pskip=1 chroma_qp_off 1 open_gop=0 weightp=2 keyint=250 keyint_min=25 scenecut=40 intra_refresh=0 rc_l Output #0, mp4, to 'goodsample.mp4': Metadata: encoder : Lavf52.111.0 Stream #0.0: Video: libx264, yuv420p, 1280x720 [PAR 45:44 DAR 20:11], q=2-31 Stream #0.1: Audio: libmp3lame, 44100 Hz, stereo, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop, [?] for help [mp3 @ 0x191d4100] Header missing Error while decoding stream #0.1 [mpeg4 @ 0x191d1dc0] Invalid and inefficient vfw-avi packed B frames detected [mp3 @ 0x191d4100] incomplete frame 9467kB time=00:01:00.32 bitrate=1285.5kbits/ Error while decoding stream #0.1 frame= 1852 fps= 20 q=29.0 Lsize= 9652kB time=00:01:01.72 bitrate=1280.9kbits video:9121kB audio:483kB global headers:0kB muxing overhead 0.499688% frame I:11 Avg QP:16.78 size: 51456 [libx264 @ 0x191ce5a0] frame P:784 Avg QP:20.81 size: 8954 [libx264 @ 0x191ce5a0] frame B:1057 Avg QP:26.06 size: 1659 [libx264 @ 0x191ce5a0] consecutive B-frames: 22.0% 3.1% 7.5% 67.4% [libx264 @ 0x191ce5a0] mb I I16..4: 31.1% 59.8% 9.1% [libx264 @ 0x191ce5a0] mb P I16..4: 1.8% 2.6% 0.2% P16..4: 24.3% 7.0% 4.0 [libx264 @ 0x191ce5a0] mb B I16..4: 0.1% 0.1% 0.0% B16..8: 22.7% 0.8% 0.2 [libx264 @ 0x191ce5a0] 8x8 transform intra:57.0% inter:72.6% [libx264 @ 0x191ce5a0] coded y,uvDC,uvAC intra: 44.4% 33.3% 10.3% inter: 7.6% 5. [libx264 @ 0x191ce5a0] i16 v,h,dc,p: 68% 14% 8% 10% [libx264 @ 0x191ce5a0] i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 21% 14% 27% 5% 7% 7% 6 [libx264 @ 0x191ce5a0] i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 28% 14% 14% 6% 10% 9% 7 [libx264 @ 0x191ce5a0] i8c dc,h,v,p: 67% 13% 17% 3% [libx264 @ 0x191ce5a0] Weighted P-Frames: Y:1.9% UV:0.4% [libx264 @ 0x191ce5a0] ref P L0: 62.2% 12.8% 10.3% 14.5% 0.2% [libx264 @ 0x191ce5a0] ref B L0: 88.1% 5.5% 6.4% [libx264 @ 0x191ce5a0] ref B L1: 95.7% 4.3% [libx264 @ 0x191ce5a0] kb/s:1209.03 I know there is couple errors tough, but i dont know hot to fix it. Also i would be very thankfull if someone can help reduce video size but is not main problem video weights as original avi but sill.

    Read the article

  • SVN Server not responding

    - by Rob Forrest
    I've been bashing my head against a wall with this one all day and I would greatly appreciate a few more eyes on the problem at hand. We have an in-house SVN Server that contains all live and development code for our website. Our live server can connect to this and get updates from the repository. This was all working fine until we migrated the SVN Server from a physical machine to a vSphere VM. Now, for some reason that continues to fathom me, we can no longer connect to the SVN Server. The SVN Server runs CentOS 6.2, Apache and SVN 1.7.2. SELinux is well and trully disabled and the problem remains when iptables is stopped. Our production server does run an older version of CentOS and SVN but the same system worked previously so I don't think that this is the issue. Of note, if I have iptables enabled, using service iptables status, I can see a single packet coming in and being accepted but the production server simply hangs on any svn command. If I give up waiting and do a CTRL-C to break the process I get a "could not connect to server". To me it appears to be something to do with the SVN Server rejecting external connections but I have no idea how this would happen. Any thoughts on what I can try from here? Thanks, Rob Edit: Network topology Production server sits externally to our in-house SVN server. Our IPCop (?) firewall allows connections from it (and it alone) on port 80 and passes the connection to the SVN Server. The hardware is all pretty decent and I don't doubt that its doing its job correctly, especially as iptables is seeing the new connections. subversion.conf (in /etc/httpd/conf.d) LoadModule dav_svn_module modules/mod_dav_svn.so <Location /repos> DAV svn SVNPath /var/svn/repos <LimitExcept PROPFIND OPTIONS REPORT> AuthType Basic AuthName "SVN Server" AuthUserFile /var/svn/svn-auth Require valid-user </LimitExcept> </Location> ifconfig eth0 Link encap:Ethernet HWaddr 00:0C:29:5F:C8:3A inet addr:172.16.0.14 Bcast:172.16.0.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fe5f:c83a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:32317 errors:0 dropped:0 overruns:0 frame:0 TX packets:632 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2544036 (2.4 MiB) TX bytes:143207 (139.8 KiB) netstat -lntp Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN 1484/mysqld tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN 1135/rpcbind tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 1351/sshd tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN 1230/cupsd tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN 1575/master tcp 0 0 0.0.0.0:58401 0.0.0.0:* LISTEN 1153/rpc.statd tcp 0 0 0.0.0.0:5672 0.0.0.0:* LISTEN 1626/qpidd tcp 0 0 :::139 :::* LISTEN 1678/smbd tcp 0 0 :::111 :::* LISTEN 1135/rpcbind tcp 0 0 :::80 :::* LISTEN 1615/httpd tcp 0 0 :::22 :::* LISTEN 1351/sshd tcp 0 0 ::1:631 :::* LISTEN 1230/cupsd tcp 0 0 ::1:25 :::* LISTEN 1575/master tcp 0 0 :::445 :::* LISTEN 1678/smbd tcp 0 0 :::56799 :::* LISTEN 1153/rpc.statd iptables --list -v -n (when iptables is stopped) Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination iptables --list -v -n (when iptables is running, after one attempted svn connection) Chain INPUT (policy ACCEPT 68 packets, 6561 bytes) pkts bytes target prot opt in out source destination 19 1304 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 0 0 ACCEPT icmp -- * * 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22 1 60 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:80 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:80 0 0 ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW udp dpt:80 Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 17 packets, 1612 bytes) pkts bytes target prot opt in out source destination tcpdump 17:08:18.455114 IP 'production server'.43255 > 'svn server'.local.http: Flags [S], seq 3200354543, win 5840, options [mss 1380,sackOK,TS val 2011458346 ecr 0,nop,wscale 7], length 0 17:08:18.455169 IP 'svn server'.local.http > 'production server'.43255: Flags [S.], seq 629885453, ack 3200354544, win 14480, options [mss 1460,sackOK,TS val 816478 ecr 2011449346,nop,wscale 7], length 0 17:08:19.655317 IP 'svn server'.local.http > 'production server'k.43255: Flags [S.], seq 629885453, ack 3200354544, win 14480, options [mss 1460,sackOK,TS val 817679 ecr 2011449346,nop,wscale 7], length 0

    Read the article

  • Web browsing is fast, but downloads are slow

    - by Ricket
    I work for a company on my university's campus, helping with general IT problems and some web development. But lately there has been a problem that has me and my boss completely stumped. We, plus one contractor, make up the entire IT department, so I'm reaching out to you for help. All around the office, we have wall jacks. These collect in a closet down the hall and all plug into a switch. This switch, along with our individual server jacks, plugs into another switch, and that switch plugs into our firewall hardware. Then the firewall is connected out to our campus network. Our campus internet is, well, very fast. I don't know exactly the terms, tiers, etc., but we have thousands of students and downloads can run as fast as 10 MB/s at night; uploads are sometimes even faster. I think we're practically ISP level. In short, I have a lot of faith that it is not the campus side of things that is causing a problem, combined with other evidence I'll mention in a moment. So our symptoms: web browsing is fast. Web pages, images, etc. load instantly. No problems there. But then when I go to download something, the download starts fast but very quickly (a matter of seconds) drops to nearly 0. Often it will actually drop to 0 and time out. This happens with even very small files, 1 MB or less. It smells to me like a QoS sort of thing. I'm not entirely sure, and I wanted to get your opinions first. My boss is hesitant to touch our firewall, much less let me touch it, and it was set up and is managed by a consultant remotely. These problems don't seem tied to a time of the day. I've tried downloads after 5:00 and still the same thing happens. From my desk, I can turn on my wireless adapter and pick up the campus wireless access point. If I unplug ethernet and connect to it, downloads are fast. This adds to my suspicion that it's limited to our company network. Also, a number of weeks ago the consultant upgraded our firewall firmware. Suddenly everything was very fast. I tested with downloads from Sun and speedtest.net and things were blazing fast, as they should be with our campus internet! It was wonderful, and I figured the slow speeds were an old firmware bug. In a matter of days, things steadily declined until they were back to the old symptoms. Oh, and we have antivirus installed on every computer, and we keep it up to date. Though I suppose the possibility is still there that someone could have spyware which is bogging down our internet, in which case what is the easiest/best way to find this out? (maybe this should go in a separate question) Thank you for your patience in reading all of this. Do you have any ideas as to what I can try? Is this something that you've experienced before? What sort of tools or methods can I use to try and diagnose the problem? P.S. everything here is Windows. Windows Server 2003 and 2008 on our servers, and Windows XP on employees' machines. Update: We are submitting a ticket to the university to just take a look and see if they see anything unusual and/or can suggestion methods for us to try and pinpoint our problem. Hopefully they'll be helpful! I'll update this to let you know what goes on. Update again: We found a hub (yes, a HUB) right between our campus connection and our firewall. It had only those two ethernet cables plugged into it, nothing else. After removing the hub, our speeds have jumped up to several mbps. However in talking with the campus, we got them to run a gigabit line to our firewall in place of the 100mbps line. As of friday, we are at about 65 mbps up and down (according to speedtest.net at 8am)!! Go NC State!!

    Read the article

  • Nginx HTTPS redirects causing loop

    - by Ben Chiappetta
    I've been banging my head against the wall trying to figure this out, so if anyone can help I'd appreciate it. My Nginx conf has three different redirect loops, haven't been able to get any of the three to work right. The three problem areas are: Redirecting memcache directory to SSL Redirecting accounts directory to SSL Redirecting SSL to www if non-www nginx.conf: user nginx; worker_processes 1; error_log /var/log/nginx/error.log warn; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log main; error_log /var/log/nginx/error.log notice; sendfile on; #tcp_nopush on; keepalive_timeout 65; proxy_set_header X-Url-Scheme $scheme; #gzip on; rewrite_log on; include /etc/nginx/conf.d/*.conf; } conf.d/default.conf: server { listen 80; server_name <redacted>.net; rewrite ^(.*) http://www.<redacted>.net$1; } server { listen 80; server_name www.<redacted>.net; set_real_ip_from 192.168.30.4; set_real_ip_from 192.168.30.5; set_real_ip_from 192.168.30.10; real_ip_header X-Forwarded-For; #charset koi8-r; access_log /var/log/nginx/host.access.log main; root /var/www/html; index index.php index.html index.htm; location =/memcache { rewrite ^/(.*)$ https://$server_name$request_uri? permanent; } location /accounts { rewrite ^/(.*)$ https://$server_name$request_uri? permanent; } #error_page 404 /404.html; # redirect server error pages to the static page /50x.html # error_page 500 502 503 504 /50x.html; location = /50x.html { } # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 # location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include /etc/nginx/fastcgi_params; try_files $uri = 404; } # deny access to .htaccess files, if Apache's document root # concurs with nginx's one # location ~ /\.ht { deny all; } } conf.d/ssl.conf: # HTTPS server # server { listen 443; server_name <redacted>.net; rewrite ^(.*) https://www.<redacted>.net$1; } server { listen 443 default_server ssl; server_name www.<redacted>.net; set_real_ip_from 192.168.30.4; set_real_ip_from 192.168.30.5; set_real_ip_from 192.168.30.10; real_ip_header X-Forwarded-For; proxy_set_header X-Forwarded_Proto https; proxy_set_header Host $host; proxy_redirect off; proxy_max_temp_file_size 0; proxy_set_header X-Forwarded-Ssl on; set $https_enabled on; ssl_certificate <redacted>.crt; ssl_certificate_key <redacted>.key; ssl_session_timeout 5m; ssl_protocols SSLv2 SSLv3 TLSv1; ssl_ciphers HIGH:!aNULL:!MD5; ssl_prefer_server_ciphers on; root /var/www/html; index index.php index.html index.htm; location /memcache { auth_basic "Restricted"; auth_basic_user_file $document_root/memcache/.htpasswd; } location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param HTTPS on; include /etc/nginx/fastcgi_params; try_files $uri = 404; } }

    Read the article

  • Stumped by "The remote server returned an error: (403) Forbidden" with WCF Service in https

    - by RJ
    I have a WCF Service that I have boiled down to next to nothing because of this error. It is driving me up the wall. Here's what I have now. A very simple WCF service with one method that returns a string with the value, "test". A very simple Web app that uses the service and puts the value of the string into a label. A web server running IIS 6 on Win 2003 with a SSL certificate. Other WCF services on the same server that work. I publish the WCF service to it's https location I run the web app in debug mode in VS and it works perfectly. I publish the web app to it's https location on the same server the WCF service resides under the same SSL certificate I get, "The remote server returned an error: (403) Forbidden" I have changed almost every setting in IIS as well as the WCF and Web apps to no avail. I have compared setting in the WCF services that work and everything is the same. Below are the setting in the web.config for the WCF Service and the WEB app: It appears the problem has to do with the Web app but I am out of ideas. Any ideas: WCF Service: <system.serviceModel> <bindings> <client /> <services> <service behaviorConfiguration="Ucf.Smtp.Wcf.SmtpServiceBehavior" name="Ucf.Smtp.Wcf.SmtpService"> <host> <baseAddresses> <add baseAddress="https://test.net.ucf.edu/webservices/Smtp/" /> </baseAddresses> </host> <endpoint address="" binding="wsHttpBinding" contract="Ucf.Smtp.Wcf.ISmtpService" bindingConfiguration="SSLBinding"> <identity> <dns value="localhost"/> </identity> </endpoint> <endpoint address="mex" binding="mexHttpsBinding" contract="IMetadataExchange"/> </service> </services> <behaviors> <serviceBehaviors> <behavior name="Ucf.Smtp.Wcf.SmtpServiceBehavior"> <serviceMetadata httpsGetEnabled="true" /> <serviceDebug includeExceptionDetailInFaults="true" httpsHelpPageEnabled="True"/> </behavior> </serviceBehaviors> </behaviors> Web App: <system.serviceModel> <bindings><wsHttpBinding> <binding name="WSHttpBinding_ISmtpService" closeTimeout="00:01:00" openTimeout="00:01:00" receiveTimeout="00:10:00" sendTimeout="00:01:00" bypassProxyOnLocal="false" transactionFlow="false" hostNameComparisonMode="StrongWildcard" maxBufferPoolSize="524288" maxReceivedMessageSize="65536" messageEncoding="Text" textEncoding="utf-8" useDefaultWebProxy="true" allowCookies="false"> <readerQuotas maxDepth="32" maxStringContentLength="8192" maxArrayLength="16384" maxBytesPerRead="4096" maxNameTableCharCount="16384" /> <reliableSession ordered="true" inactivityTimeout="00:10:00" enabled="false" /> <security mode="Transport"> <transport clientCredentialType="None" proxyCredentialType="None" realm="" /> <message clientCredentialType="Windows" negotiateServiceCredential="true" establishSecurityContext="true" /> </security> </binding> <client> <endpoint address="https://net228.net.ucf.edu/webservices/smtp/SmtpService.svc" binding="wsHttpBinding" bindingConfiguration="WSHttpBinding_ISmtpService" contract="SmtpService.ISmtpService" name="WSHttpBinding_ISmtpService"> <identity> <dns value="localhost" /> </identity> </client> </system.serviceModel>

    Read the article

  • mysql-connector-c++ - ‘get_driver_instance’ is not a member of ‘sql::mysql’

    - by rizzo0917
    I am a beginner at c++ and figured the only way I am going to learn is to get dirty with some code. I am trying to build a program that connects to a mysql database. I am using g++, on linux. With no ide. I run "make" and this is my error: hello.cpp:38: error: ‘get_driver_instance’ is not a member of ‘sql::mysql’ make: *** [hello.o] Error 1 Here is my code including makefile. Any Help would be great! Thanks in advance ###BEGIN hello.cpp### #include <stdlib.h> #include <iostream> #include <sstream> #include <stdexcept> #include "mysql_connection.h" #include <cppconn/driver.h> #include <cppconn/exception.h> #include <cppconn/resultset.h> #include <cppconn/statement.h> #include <cppconn/prepared_statement.h> #define EXAMPLE_HOST "localhost" #define EXAMPLE_USER "root" #define EXAMPLE_PASS "" #define EXAMPLE_DB "world" using namespace std; using namespace sql::mysql; int main(int argc, const char **argv) { string url(argc >= 2 ? argv[1] : EXAMPLE_HOST); const string user(argc >= 3 ? argv[2] : EXAMPLE_USER); const string pass(argc >= 4 ? argv[3] : EXAMPLE_PASS); const string database(argc >= 5 ? argv[4] : EXAMPLE_DB); cout << "Connector/C++ tutorial framework..." << endl; cout << endl; try { sql::Driver *driver; sql::Connection *con; sql::Statement *stmt; driver = sql::mysql::get_driver_instance(); con = driver->connect("tcp://127.0.0.1:3306", "user", "password"); stmt = con->createStatement(); stmt->execute("USE " EXAMPLE_DB); stmt->execute("DROP TABLE IF EXISTS test"); stmt->execute("CREATE TABLE test(id INT, label CHAR(1))"); stmt->execute("INSERT INTO test(id, label) VALUES (1, 'a')"); delete stmt; delete con; } catch (sql::SQLException &e) { /* The MySQL Connector/C++ throws three different exceptions: - sql::MethodNotImplementedException (derived from sql::SQLException) - sql::InvalidArgumentException (derived from sql::SQLException) - sql::SQLException (derived from std::runtime_error) */ cout << "# ERR: SQLException in " << __FILE__; cout << "(" << __FUNCTION__ << ") on line " << __LINE__ << endl; /* Use what() (derived from std::runtime_error) to fetch the error message */ cout << "# ERR: " << e.what(); cout << " (MySQL error code: " << e.getErrorCode(); cout << ", SQLState: " << e.getSQLState() << " )" << endl; return EXIT_FAILURE; } cout << "Done." << endl; return EXIT_SUCCESS; } ###END hello.cpp### ###BEGIN Make File### SRCS := hello.cpp OBJS := $(SRCS:.cpp=.o) CXXFLAGS := -Wall -pedantic INCPATHS := -I/home/user/mysql-connector/include/ LIBPATHS := -L/home/user/mysql-connector/lib/ -L/home/user/mysql-connector-c/lib/ LIBS := -static -lmysqlclient -mysqlcppconn-static EXE := MyExecutable $(EXE): $(OBJS) $(CXX) $(OBJS) $(LIBPATHS) $(LIBS) -o $@ .cpp.o: $(CXX) $(CXXFLAGS) $(INCPATHS) -c $< -o $@ ###End Makefile###

    Read the article

  • How to Reuse Your Old Wi-Fi Router as a Network Switch

    - by Jason Fitzpatrick
    Just because your old Wi-Fi router has been replaced by a newer model doesn’t mean it needs to gather dust in the closet. Read on as we show you how to take an old and underpowered Wi-Fi router and turn it into a respectable network switch (saving your $20 in the process). Image by mmgallan. Why Do I Want To Do This? Wi-Fi technology has changed significantly in the last ten years but Ethernet-based networking has changed very little. As such, a Wi-Fi router with 2006-era guts is lagging significantly behind current Wi-Fi router technology, but the Ethernet networking component of the device is just as useful as ever; aside from potentially being only 100Mbs instead of 1000Mbs capable (which for 99% of home applications is irrelevant) Ethernet is Ethernet. What does this matter to you, the consumer? It means that even though your old router doesn’t hack it for your Wi-Fi needs any longer the device is still a perfectly serviceable (and high quality) network switch. When do you need a network switch? Any time you want to share an Ethernet cable among multiple devices, you need a switch. For example, let’s say you have a single Ethernet wall jack behind your entertainment center. Unfortunately you have four devices that you want to link to your local network via hardline including your smart HDTV, DVR, Xbox, and a little Raspberry Pi running XBMC. Instead of spending $20-30 to purchase a brand new switch of comparable build quality to your old Wi-Fi router it makes financial sense (and is environmentally friendly) to invest five minutes of your time tweaking the settings on the old router to turn it from a Wi-Fi access point and routing tool into a network switch–perfect for dropping behind your entertainment center so that your DVR, Xbox, and media center computer can all share an Ethernet connection. What Do I Need? For this tutorial you’ll need a few things, all of which you likely have readily on hand or are free for download. To follow the basic portion of the tutorial, you’ll need the following: 1 Wi-Fi router with Ethernet ports 1 Computer with Ethernet jack 1 Ethernet cable For the advanced tutorial you’ll need all of those things, plus: 1 copy of DD-WRT firmware for your Wi-Fi router We’re conducting the experiment with a Linksys WRT54GL Wi-Fi router. The WRT54 series is one of the best selling Wi-Fi router series of all time and there’s a good chance a significant number of readers have one (or more) of them stuffed in an office closet. Even if you don’t have one of the WRT54 series routers, however, the principles we’re outlining here apply to all Wi-Fi routers; as long as your router administration panel allows the necessary changes you can follow right along with us. A quick note on the difference between the basic and advanced versions of this tutorial before we proceed. Your typical Wi-Fi router has 5 Ethernet ports on the back: 1 labeled “Internet”, “WAN”, or a variation thereof and intended to be connected to your DSL/Cable modem, and 4 labeled 1-4 intended to connect Ethernet devices like computers, printers, and game consoles directly to the Wi-Fi router. When you convert a Wi-Fi router to a switch, in most situations, you’ll lose two port as the “Internet” port cannot be used as a normal switch port and one of the switch ports becomes the input port for the Ethernet cable linking the switch to the main network. This means, referencing the diagram above, you’d lose the WAN port and LAN port 1, but retain LAN ports 2, 3, and 4 for use. If you only need to switch for 2-3 devices this may be satisfactory. However, for those of you that would prefer a more traditional switch setup where there is a dedicated WAN port and the rest of the ports are accessible, you’ll need to flash a third-party router firmware like the powerful DD-WRT onto your device. Doing so opens up the router to a greater degree of modification and allows you to assign the previously reserved WAN port to the switch, thus opening up LAN ports 1-4. Even if you don’t intend to use that extra port, DD-WRT offers you so many more options that it’s worth the extra few steps. Preparing Your Router for Life as a Switch Before we jump right in to shutting down the Wi-Fi functionality and repurposing your device as a network switch, there are a few important prep steps to attend to. First, you want to reset the router (if you just flashed a new firmware to your router, skip this step). Following the reset procedures for your particular router or go with what is known as the “Peacock Method” wherein you hold down the reset button for thirty seconds, unplug the router and wait (while still holding the reset button) for thirty seconds, and then plug it in while, again, continuing to hold down the rest button. Over the life of a router there are a variety of changes made, big and small, so it’s best to wipe them all back to the factory default before repurposing the router as a switch. Second, after resetting, we need to change the IP address of the device on the local network to an address which does not directly conflict with the new router. The typical default IP address for a home router is 192.168.1.1; if you ever need to get back into the administration panel of the router-turned-switch to check on things or make changes it will be a real hassle if the IP address of the device conflicts with the new home router. The simplest way to deal with this is to assign an address close to the actual router address but outside the range of addresses that your router will assign via the DHCP client; a good pick then is 192.168.1.2. Once the router is reset (or re-flashed) and has been assigned a new IP address, it’s time to configure it as a switch. Basic Router to Switch Configuration If you don’t want to (or need to) flash new firmware onto your device to open up that extra port, this is the section of the tutorial for you: we’ll cover how to take a stock router, our previously mentioned WRT54 series Linksys, and convert it to a switch. Hook the Wi-Fi router up to the network via one of the LAN ports (consider the WAN port as good as dead from this point forward, unless you start using the router in its traditional function again or later flash a more advanced firmware to the device, the port is officially retired at this point). Open the administration control panel via  web browser on a connected computer. Before we get started two things: first,  anything we don’t explicitly instruct you to change should be left in the default factory-reset setting as you find it, and two, change the settings in the order we list them as some settings can’t be changed after certain features are disabled. To start, let’s navigate to Setup ->Basic Setup. Here you need to change the following things: Local IP Address: [different than the primary router, e.g. 192.168.1.2] Subnet Mask: [same as the primary router, e.g. 255.255.255.0] DHCP Server: Disable Save with the “Save Settings” button and then navigate to Setup -> Advanced Routing: Operating Mode: Router This particular setting is very counterintuitive. The “Operating Mode” toggle tells the device whether or not it should enable the Network Address Translation (NAT)  feature. Because we’re turning a smart piece of networking hardware into a relatively dumb one, we don’t need this feature so we switch from Gateway mode (NAT on) to Router mode (NAT off). Our next stop is Wireless -> Basic Wireless Settings: Wireless SSID Broadcast: Disable Wireless Network Mode: Disabled After disabling the wireless we’re going to, again, do something counterintuitive. Navigate to Wireless -> Wireless Security and set the following parameters: Security Mode: WPA2 Personal WPA Algorithms: TKIP+AES WPA Shared Key: [select some random string of letters, numbers, and symbols like JF#d$di!Hdgio890] Now you may be asking yourself, why on Earth are we setting a rather secure Wi-Fi configuration on a Wi-Fi router we’re not going to use as a Wi-Fi node? On the off chance that something strange happens after, say, a power outage when your router-turned-switch cycles on and off a bunch of times and the Wi-Fi functionality is activated we don’t want to be running the Wi-Fi node wide open and granting unfettered access to your network. While the chances of this are next-to-nonexistent, it takes only a few seconds to apply the security measure so there’s little reason not to. Save your changes and navigate to Security ->Firewall. Uncheck everything but Filter Multicast Firewall Protect: Disable At this point you can save your changes again, review the changes you’ve made to ensure they all stuck, and then deploy your “new” switch wherever it is needed. Advanced Router to Switch Configuration For the advanced configuration, you’ll need a copy of DD-WRT installed on your router. Although doing so is an extra few steps, it gives you a lot more control over the process and liberates an extra port on the device. Hook the Wi-Fi router up to the network via one of the LAN ports (later you can switch the cable to the WAN port). Open the administration control panel via web browser on the connected computer. Navigate to the Setup -> Basic Setup tab to get started. In the Basic Setup tab, ensure the following settings are adjusted. The setting changes are not optional and are required to turn the Wi-Fi router into a switch. WAN Connection Type: Disabled Local IP Address: [different than the primary router, e.g. 192.168.1.2] Subnet Mask: [same as the primary router, e.g. 255.255.255.0] DHCP Server: Disable In addition to disabling the DHCP server, also uncheck all the DNSMasq boxes as the bottom of the DHCP sub-menu. If you want to activate the extra port (and why wouldn’t you), in the WAN port section: Assign WAN Port to Switch [X] At this point the router has become a switch and you have access to the WAN port so the LAN ports are all free. Since we’re already in the control panel, however, we might as well flip a few optional toggles that further lock down the switch and prevent something odd from happening. The optional settings are arranged via the menu you find them in. Remember to save your settings with the save button before moving onto a new tab. While still in the Setup -> Basic Setup menu, change the following: Gateway/Local DNS : [IP address of primary router, e.g. 192.168.1.1] NTP Client : Disable The next step is to turn off the radio completely (which not only kills the Wi-Fi but actually powers the physical radio chip off). Navigate to Wireless -> Advanced Settings -> Radio Time Restrictions: Radio Scheduling: Enable Select “Always Off” There’s no need to create a potential security problem by leaving the Wi-Fi radio on, the above toggle turns it completely off. Under Services -> Services: DNSMasq : Disable ttraff Daemon : Disable Under the Security -> Firewall tab, uncheck every box except “Filter Multicast”, as seen in the screenshot above, and then disable SPI Firewall. Once you’re done here save and move on to the Administration tab. Under Administration -> Management:  Info Site Password Protection : Enable Info Site MAC Masking : Disable CRON : Disable 802.1x : Disable Routing : Disable After this final round of tweaks, save and then apply your settings. Your router has now been, strategically, dumbed down enough to plod along as a very dependable little switch. Time to stuff it behind your desk or entertainment center and streamline your cabling.     

    Read the article

  • facebook iframe stream.Publish cannot close dialog or skip

    - by fooyee
    am pulling my hair over this :( spent 10 hrs but nothing came out I read this thread http://forum.developers.facebook.com/viewtopic.php?pid=198128 but it didn't help much. I'm running a local dev App Engine server ( localhost:8080 ) iframe app so I have a couple of problems. 1) on safari 4.0.4, the publish story dialog comes up nicely with all images/data/action_links. upon posting a story (or skipping), the dialog goes blank and wouldn't close. 2) I tested the same code on firefox 3.5.8, the dialog comes up with all images/data/action_links, but then the whole thing freezes. Clicking anywhere on the dialog doesn't help at all. If i'm patient enough and click "publish", I have to wait for abt 10 seconds before the dialog says "story is published". then it freezes. (clicking on skip doesn't make a difference). btw, there is no "button clicking effect" : ie: the buttons don't look like they "sink down" upon clicking. I checked the firefox memory using the command "top" on the terminal, it all seems okay, no spike in CPU processes ( i could open other firefox tabs and work on them) My futile attempts at solving the problems... 1) so i thought, hmm could this be because of local dev (localhost) problem? I uploaded the code to the production server, the same thing happens. 2) I tried an older firefox (3.1) and the same problem persisted ( the freezing ) 3) I noticed that i kind of used 2 different FB features ( Connect and XFBML). The Connect Feature I used in the PostStory function. The XFBML feature I used before the tag. So I thought, hmm ... I tried replacing the FB_RequireFeatures["Connect"] feature with FB_RequireFeatures["XFBML"]. nothing changed. I still can't close the story dialog. 4) Is there a possibility that I didn't connect to xd_receiver.htm properly? my xd_receiver.htm is stored in my folder /media/fbconnect in my app.yaml handler: - url: /fbconnect static_dir: media/fbconnect so i thought a connection has to be established with xd_receiver.htm. any way I can test that? here're all the codes: <script type="text/javascript"> //post story function function PostStory() { //init facebook FB_RequireFeatures(["Connect"], function() { FB.Facebook.init('my_app_key', "/fbconnect/xd_receiver.htm"); FB.ensureInit(function() { var message = 'the message'; var attachment = { 'name': 'a simple app to send gifts', 'href': 'http://apps.facebook.com/my_app_name', 'caption': '{*actor*} sent u something', 'description': 'some description', "media": [{ "type": "image", "src": "http://bit.ly/105QYr", "href": "http://bit.ly/105QYr"}] }; //action links can only be seen AFTER the feed is published var action_links = [{ 'text': 'Send him/her a gift back!', 'href': 'http://somelink.com'}]; FB.Connect.streamPublish(message, attachment, action_links, null, "Share the gift with your friends", callback, false, null); }); }); function callback(post_id, exception) { //alert('Wall Post Complete'); } } </script> just before the end of the /body tag, i have this: <script type="text/javascript"> function callFBInit() { FB_RequireFeatures( ["XFBML"], function(){ FB.Facebook.init("my_app_key", "/fbconnect/xd_receiver.htm"); } ); } callFBInit(); btw, my xd_receiver.htm contains: <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Strict//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd"> <html xmlns=? http://www.w3.org/1999/xhtml? > <head> <title>cross-domain receiver page</title> </head> <body> <script src=?http://static.ak.facebook.com/js/api_lib/v0.4/xdcommreceiver.debug.js? type=? text/javascript? ></script> </body> </html> hope you guys can help out. thx

    Read the article

  • Point of contact of 2 OBBs?

    - by Milo
    I'm working on the physics for my GTA2-like game so I can learn more about game physics. The collision detection and resolution are working great. I'm now just unsure how to compute the point of contact when I hit a wall. Here is my OBB class: public class OBB2D { private Vector2D projVec = new Vector2D(); private static Vector2D projAVec = new Vector2D(); private static Vector2D projBVec = new Vector2D(); private static Vector2D tempNormal = new Vector2D(); private Vector2D deltaVec = new Vector2D(); // Corners of the box, where 0 is the lower left. private Vector2D corner[] = new Vector2D[4]; private Vector2D center = new Vector2D(); private Vector2D extents = new Vector2D(); private RectF boundingRect = new RectF(); private float angle; //Two edges of the box extended away from corner[0]. private Vector2D axis[] = new Vector2D[2]; private double origin[] = new double[2]; public OBB2D(float centerx, float centery, float w, float h, float angle) { for(int i = 0; i < corner.length; ++i) { corner[i] = new Vector2D(); } for(int i = 0; i < axis.length; ++i) { axis[i] = new Vector2D(); } set(centerx,centery,w,h,angle); } public OBB2D(float left, float top, float width, float height) { for(int i = 0; i < corner.length; ++i) { corner[i] = new Vector2D(); } for(int i = 0; i < axis.length; ++i) { axis[i] = new Vector2D(); } set(left + (width / 2), top + (height / 2),width,height,0.0f); } public void set(float centerx,float centery,float w, float h,float angle) { float vxx = (float)Math.cos(angle); float vxy = (float)Math.sin(angle); float vyx = (float)-Math.sin(angle); float vyy = (float)Math.cos(angle); vxx *= w / 2; vxy *= (w / 2); vyx *= (h / 2); vyy *= (h / 2); corner[0].x = centerx - vxx - vyx; corner[0].y = centery - vxy - vyy; corner[1].x = centerx + vxx - vyx; corner[1].y = centery + vxy - vyy; corner[2].x = centerx + vxx + vyx; corner[2].y = centery + vxy + vyy; corner[3].x = centerx - vxx + vyx; corner[3].y = centery - vxy + vyy; this.center.x = centerx; this.center.y = centery; this.angle = angle; computeAxes(); extents.x = w / 2; extents.y = h / 2; computeBoundingRect(); } //Updates the axes after the corners move. Assumes the //corners actually form a rectangle. private void computeAxes() { axis[0].x = corner[1].x - corner[0].x; axis[0].y = corner[1].y - corner[0].y; axis[1].x = corner[3].x - corner[0].x; axis[1].y = corner[3].y - corner[0].y; // Make the length of each axis 1/edge length so we know any // dot product must be less than 1 to fall within the edge. for (int a = 0; a < axis.length; ++a) { float l = axis[a].length(); float ll = l * l; axis[a].x = axis[a].x / ll; axis[a].y = axis[a].y / ll; origin[a] = corner[0].dot(axis[a]); } } public void computeBoundingRect() { boundingRect.left = JMath.min(JMath.min(corner[0].x, corner[3].x), JMath.min(corner[1].x, corner[2].x)); boundingRect.top = JMath.min(JMath.min(corner[0].y, corner[1].y),JMath.min(corner[2].y, corner[3].y)); boundingRect.right = JMath.max(JMath.max(corner[1].x, corner[2].x), JMath.max(corner[0].x, corner[3].x)); boundingRect.bottom = JMath.max(JMath.max(corner[2].y, corner[3].y),JMath.max(corner[0].y, corner[1].y)); } public void set(RectF rect) { set(rect.centerX(),rect.centerY(),rect.width(),rect.height(),0.0f); } // Returns true if other overlaps one dimension of this. private boolean overlaps1Way(OBB2D other) { for (int a = 0; a < axis.length; ++a) { double t = other.corner[0].dot(axis[a]); // Find the extent of box 2 on axis a double tMin = t; double tMax = t; for (int c = 1; c < corner.length; ++c) { t = other.corner[c].dot(axis[a]); if (t < tMin) { tMin = t; } else if (t > tMax) { tMax = t; } } // We have to subtract off the origin // See if [tMin, tMax] intersects [0, 1] if ((tMin > 1 + origin[a]) || (tMax < origin[a])) { // There was no intersection along this dimension; // the boxes cannot possibly overlap. return false; } } // There was no dimension along which there is no intersection. // Therefore the boxes overlap. return true; } public void moveTo(float centerx, float centery) { float cx,cy; cx = center.x; cy = center.y; deltaVec.x = centerx - cx; deltaVec.y = centery - cy; for (int c = 0; c < 4; ++c) { corner[c].x += deltaVec.x; corner[c].y += deltaVec.y; } boundingRect.left += deltaVec.x; boundingRect.top += deltaVec.y; boundingRect.right += deltaVec.x; boundingRect.bottom += deltaVec.y; this.center.x = centerx; this.center.y = centery; computeAxes(); } // Returns true if the intersection of the boxes is non-empty. public boolean overlaps(OBB2D other) { if(right() < other.left()) { return false; } if(bottom() < other.top()) { return false; } if(left() > other.right()) { return false; } if(top() > other.bottom()) { return false; } if(other.getAngle() == 0.0f && getAngle() == 0.0f) { return true; } return overlaps1Way(other) && other.overlaps1Way(this); } public Vector2D getCenter() { return center; } public float getWidth() { return extents.x * 2; } public float getHeight() { return extents.y * 2; } public void setAngle(float angle) { set(center.x,center.y,getWidth(),getHeight(),angle); } public float getAngle() { return angle; } public void setSize(float w,float h) { set(center.x,center.y,w,h,angle); } public float left() { return boundingRect.left; } public float right() { return boundingRect.right; } public float bottom() { return boundingRect.bottom; } public float top() { return boundingRect.top; } public RectF getBoundingRect() { return boundingRect; } public boolean overlaps(float left, float top, float right, float bottom) { if(right() < left) { return false; } if(bottom() < top) { return false; } if(left() > right) { return false; } if(top() > bottom) { return false; } return true; } public static float distance(float ax, float ay,float bx, float by) { if (ax < bx) return bx - ay; else return ax - by; } public Vector2D project(float ax, float ay) { projVec.x = Float.MAX_VALUE; projVec.y = Float.MIN_VALUE; for (int i = 0; i < corner.length; ++i) { float dot = Vector2D.dot(corner[i].x,corner[i].y,ax,ay); projVec.x = JMath.min(dot, projVec.x); projVec.y = JMath.max(dot, projVec.y); } return projVec; } public Vector2D getCorner(int c) { return corner[c]; } public int getNumCorners() { return corner.length; } public static float collisionResponse(OBB2D a, OBB2D b, Vector2D outNormal) { float depth = Float.MAX_VALUE; for (int i = 0; i < a.getNumCorners() + b.getNumCorners(); ++i) { Vector2D edgeA; Vector2D edgeB; if(i >= a.getNumCorners()) { edgeA = b.getCorner((i + b.getNumCorners() - 1) % b.getNumCorners()); edgeB = b.getCorner(i % b.getNumCorners()); } else { edgeA = a.getCorner((i + a.getNumCorners() - 1) % a.getNumCorners()); edgeB = a.getCorner(i % a.getNumCorners()); } tempNormal.x = edgeB.x -edgeA.x; tempNormal.y = edgeB.y - edgeA.y; tempNormal.normalize(); projAVec.equals(a.project(tempNormal.x,tempNormal.y)); projBVec.equals(b.project(tempNormal.x,tempNormal.y)); float distance = OBB2D.distance(projAVec.x, projAVec.y,projBVec.x,projBVec.y); if (distance > 0.0f) { return 0.0f; } else { float d = Math.abs(distance); if (d < depth) { depth = d; outNormal.equals(tempNormal); } } } float dx,dy; dx = b.getCenter().x - a.getCenter().x; dy = b.getCenter().y - a.getCenter().y; float dot = Vector2D.dot(dx,dy,outNormal.x,outNormal.y); if(dot > 0) { outNormal.x = -outNormal.x; outNormal.y = -outNormal.y; } return depth; } public Vector2D getMoveDeltaVec() { return deltaVec; } }; Thanks!

    Read the article

  • CodePlex Daily Summary for Friday, April 16, 2010

    CodePlex Daily Summary for Friday, April 16, 2010New Projects[C#] UML Touch: This project is my master thesis project for Msc Software Engineering at Oxford Brookes univesity. The goal of this project is to develop a UML Edi...3D Chart Reports, using ASP.NET 2.0: Project focuses on the visibility of internal supply chain management process. The objective is materialized, using MSChart and hence provides asse...Active Directory Health: ActiveDirectoryHealth (ADHealth) Aim: To create a suite of tools to allow an Active Directory administrator monitor and identify problems, particu...Art4Desktop: Aplicação desktop simplesAuto Increment field for any entity in MS CRM: Auto Increment field for any entity in MS CRM will add an attribute in any entity which will be auto increment type.Convection Game Engine (Basic Edition): A basic 2D game engine written in C# using XNA 3.1CSharp Intellisense: VS 2010 IntelliSense plug-in Provides custom IntelliSense for the CSharp Editor that is capable to filter out events, preoperties or methods. ...EP: Generic platform for enterprise applications developed on .NETFile Change Checker: A simple windows form application that checks and copies all modified files given a specified date. It aims to help developers that use Visual Stu...Folder: Folder is a puzzle platformer game, which provides you a whole new experience. You can fold objects in game play; a wall becomes a road, a high sti...Industrial Dashboard: WCF service that allows executing SQL Server stored procedures straight from javascript code, enabling sending and receiving structured data withou...kafrilion: Open Source Platform GameLogikBug.Injection: LogikBug.Injection is an IOC container and is very light weight. It is very simple to use and yet very roboust, there are many options and ways to ...MongoMvc: NoSql with MongoDB, NoRM and ASP.NET MVC. For more details check out the blog post http://weblogs.asp.net/shijuvarghese/archive/2010/04/16/nosql-wi...MOSSDAL: MOSS Data Access Layer for data from the Sharepoint Lists Service: MOSSDAL is a lightweight framework for working with Sharepoint MOSS List data using the List web Service. It can be used with silverlight or regul...Should: This is a set of test framework agnostic extensions assetion extensions. This project was born because test runners Should be independent of the...Software Localization Tool: summaryTIMETABLEASY: planning managerTR9: implementions of t9 technologies from mobile device to personal computer and laptopTrp net tools: net toolTwep: Twep is a JavaScript lib.Using PowerPivot to analyze MS Dynamics NAV: Project show how to prepare MS Dynamics NAV data for analyzing in PowerPivot for Excel. Project include Data Warehouse demo database, sql procedure...vmware virtual mashines management system for education: System for management many classes with PC and VMware virtual mashines (bad english,sorry)WebSite: Mr. John's projectsWebtrends DX and DC Services Libraries: This project is setup to provide assemblies to simplify access to the REST based DX and DC Web Services that Webtrends Provides. For access you ne...YetAnotherFileRenamer: Searches a directory and/or sub-directories for files matching a certain extension and copies and renames them to the same folder. The intent is a...New Releases3D Chart Reports, using ASP.NET 2.0: Beta iscm1.0.0.1: Its first release, might be a tolerant to bugs.A Guide to Parallel Programming: Drop 2 - Guide Chapters 2 and 5, accompanying code: This is Drop 2 with just the Guide Chapters 2 and 5 and the accompanying code samples. This drop requires Visual Studio 2010 Beta 2 or later in ord...AnimeJ: AnimeJ 1.1: This new release features reversible animations. It is fully backward compatible, and by simply specifying an additional parameter to Run() you can...AutoPoco: AutoPoco 0.4: A load of additions to the convention system Inheritance precedence added And a pile of extra data sourcesCSharp Intellisense: V1.5: CSharpIntellisensePresenter(Free) Created by: Bnaya Eshet (Bnaya Eshet (credit to Karl Shifflett)) Last Updated: Tuesday, April 13, 2010 Version...DevTreks -social budgeting that improves lives and livelihoods: Social Budgeting Web Software, DevTreks alpha 4: Alpha 4 upgrades all story-telling with one very basic, simple, 'story' data pattern, schema, and stylesheet. Basic, simple, stories and eBook pa...ESPEHA: Espeha 4.3: Deletion of categories and tasks via F8 Saving on CtrlS, CtrlShiftS Navigating to search on CtrlF Hiding on CtrlQ, CtrlX, CtrlH, Q, X, H + Drag ...Folder Bookmarks: Folder Bookmarks 1.4.4: This is the latest version of Folder Bookmarks (1.4.4), with general improvements. It has an installer - it will create a directory 'CPascoe' in My...HouseFly controls: HouseFly controls alpha 0.9.1: Version 0.9.1 alpha release of HouseFly controlsIndustrial Dashboard: 2.0 Beta: 2.0 Beta includes : IndustrialDashboard Framework Sample widgets : TabularReport, DropDownPicker, DatePicker, ScopePicker Sample html pageskdar: KDAR 0.0.20: KDAR - Kernel Debugger Anti Rootkit - signature's bases updated - many bugs fixedLogikBug.Injection: Initial Release: This project is dependent upon Microsoft.Practices.ServiceLocation.IServiceLocator and must be referenced when referencing LogikBug.Injection.Mesopotamia Experiment: Mesopotamia 1.2.72: New Features - Select organims to load in sim or in hw mode Fixes - fixed robotics engine not shutting down properly - selects new robotics port o...MobySharp: MobySharp 1.1: Fixed GetComments Added the new Likes featureMongoMvc: NoSQL with MongoDB, NoRM and ASP.NET MVC: A demo on NoSQL with MongoDB, NoRM and ASP.NET MVC. To run the demo application do the ollowing actions. 1. Create a directory call C:\data\...NetMassDownloader: Release 1.6.0.0: Mass Downloader For .Net Framework which allows you do download .Net Framework source code all at once.Offline debugging for VS2005 , VS2008 , Code...Nito.KitchenSink: Version 4: Features added in this release: PDBs are source-indexed to CodePlex, so it should be possible to step through the code (with on-demand downloads) w...Nito.KitchenSink: Version 5: The only feature for this release is support of the .NET 4.0 platform. Dependencies Nito.Linq 0.4 Beta (released 2010-04-15) Rx 1.0.2441.0 (rele...Nito.LINQ: Beta (v0.4): Rx version The "with Rx" versions of Nito.LINQ are built against Rx 1.0.2441.0, released 2010-04-15. Breaking changes IEnumerable<T>.Min and IEnum...N-Twill Twitter Client for VB.NET: NTWILL PROJECT 15-abril-2010: Este archivo es un Zip que contiene el proyecto hasta este punto editado... tiene algunas que otras funciones, pero lo cuelgo para tener un referen...PanBrowser: 1.2.0: added screensaver support, hit a key to exit, up/down keys cycle through images.PersianDateTimePicker, PersianMonthCalendar: PersianDatetimePicker,PersianMonthCalendar: PersianDatetimePicker,PersianMonthCalendar 1.1 releasesPokeIn Comet Ajax Library: PokeIn Library v03: New Features! Client MessageLog Management Added CrossBrowser Script Injector Added to work with non ajax supported browsers and activeX disabled...PokeIn Comet Ajax Library: PokeIn Sample VS09: Sample Project of PokeIn VS09. Contains version 0.3 of LibraryPokeIn Comet Ajax Library: PokeIn Sample VS10: Sample Visual Studio 10 project for PokeIn. Contains v03 Library of PokeInSilverlight Toolkit: April 2010: Suggestions? Features? Questions? Ask questions in our Silverlight Toolkit forum on Silverlight.net. The forum is the best resource for Silverlig...Software Localization Tool: SharpSLT 0.9: This is the first release of SharpSLT. Features Framework: .Net 3.5 UI language: English Works as standalone and External Tool for Visual C# Ex...Star Trooper for XNA 2D Tutorial: Lesson two content: Here is Lesson two original content for the StarTrooper 2D XNA tutorial. The blog tutorial has now started over on http://xna-uk.net/blogs/darkgen...StyleCop for ReSharper: StyleCop for ReSharper 5.0.14714.1: StyleCop for ReSharper 5.0.14714.1 o StyleCop 4.3.3.0 o ReSharper 5.0.1659.36 o Visual Studio 2008 / Visual Studio 2010 Installation Instructi...TaskUnZip for SSIS: TaskUnZip for SSIS 1.1.1.0 (beta 2): Ver. 1.1.1.0 (beta2) Bug: Correct installation bug. Add: Support SQL SERVER 2008 / 2005 Minor corrections Ver. 1.1.0.0 (Tnx to: Kevin Wendler)...TaskUnZip for SSIS: TaskUnZip for SSIS 1.2.0.0: Ver. 1.2.0.0 Add: Support SQL SERVER 2008 / 2005. Add: recursive compress.* Add: filter option for extract e compress file.* Add: Test archiv...Test Project (ignore): abcde: aaaaadaTR9: TR9 Beta: this setup is first release of the program.TR9: TR9 Source Code: TR9 Source CodeUsing PowerPivot to analyze MS Dynamics NAV: GL sql procedures and demo DB: For using sql procedures and creating DW database, please see Documentation.VivoSocial: VivoSocial 7.1.1: Version 7.1.1 of VivoSocial has been released. If you experienced any issues with the previous version, please update your modules to the 7.1.1 rel...WPF Inspirational Quote Management System: Release 1.1.1: - Changed to only allow one running instance a time. - Custom icon in system tray popup removed for now as this breaks when text size is set to gr...WPF ShaderEffect Generator: WPF ShaderEffect Generator 1.6.1: Just a minor release to fix the problem with resource Uri generation in the C# Shadereffect files. ChangesThe Uri should be correctly generated no...Most Popular ProjectsRawrWBFS ManagerAJAX Control ToolkitMicrosoft SQL Server Product Samples: DatabaseSilverlight ToolkitWindows Presentation Foundation (WPF)ASP.NETMicrosoft SQL Server Community & SamplesPHPExcelpatterns & practices – Enterprise LibraryMost Active ProjectsRawrpatterns & practices – Enterprise LibraryGMap.NET - Great Maps for Windows Forms & PresentationIndustrial DashboardFarseer Physics EngineIonics Isapi Rewrite FilterNB_Store - Free DotNetNuke Ecommerce Catalog ModuleBlogEngine.NETjQuery Library for SharePoint Web ServicesDotRas

    Read the article

  • utf8 problem with Perl and XML::Parser

    - by René Nyffenegger
    I encountered a problem dealing with utf8, XML and Perl. The following is the smallest piece of code and data in order to reproduce the problem. Here's an XML file that needs to be parsed: <?xml version="1.0" encoding="utf-8"?> <test> <words>???????????? ??????? ????????? ???? ???????????? ??????</words> <words>???????????? ??????? ????????? ???? ???????????? ??????</words> <words>???????????? ??????? ????????? ???? ???????????? ??????</words> [<words> .... </words> 148 times repeated] <words>???????????? ??????? ????????? ???? ???????????? ??????</words> <words>???????????? ??????? ????????? ???? ???????????? ??????</words> </test> The parsing is done with this perl script: use warnings; use strict; use XML::Parser; use Data::Dump; my $in_words = 0; my $xml_parser=new XML::Parser(Style=>'Stream'); $xml_parser->setHandlers ( Start => \&start_element, End => \&end_element, Char => \&character_data, Default => \&default); open OUT, '>out.txt'; binmode (OUT, ":utf8"); open XML, 'xml_test.xml' or die; $xml_parser->parse(*XML); close XML; close OUT; sub start_element { my($parseinst, $element, %attributes) = @_; if ($element eq 'words') { $in_words = 1; } else { $in_words = 0; } } sub end_element { my($parseinst, $element, %attributes) = @_; if ($element eq 'words') { $in_words = 0; } } sub default { # nothing to see here; } sub character_data { my($parseinst, $data) = @_; if ($in_words) { if ($in_words) { print OUT "$data\n"; } } } When the script is run, it produces the out.txt file. The problem is in this file on line 147. The 22th character (which in utf-8 consists of \xd6 \xb8) is split between the d6 and b8 with a new line. This should not happen. Now, I am interested if someone else has this problem or can reproduce it. And why I am getting this problem. I am running this script on Windows: C:\temp>perl -v This is perl, v5.10.0 built for MSWin32-x86-multi-thread (with 5 registered patches, see perl -V for more detail) Copyright 1987-2007, Larry Wall Binary build 1003 [285500] provided by ActiveState http://www.ActiveState.com Built May 13 2008 16:52:49

    Read the article

< Previous Page | 51 52 53 54 55 56 57 58 59  | Next Page >