Search Results

Search found 15824 results on 633 pages for 'event horizon'.

Page 516/633 | < Previous Page | 512 513 514 515 516 517 518 519 520 521 522 523  | Next Page >

• Windows Server 2008 - RAID 5 Fails on Reboot

  - by Adam

  Hey, I've got an install of Windows Server 2008 Enterprise. It's running software RAID-5 with five disks. The disks were originally formatted under Windows Server 2003, but came up fine once I installed Windows Server 2008. The issue I'm having is that every time I reboot the server, the RAID comes up with a "Failed Redundancy" - the data stays available. I have 4 disks on a PCI SATA controller, and one of the disks connected to the motherboard's on-board SATA ports. (The other on-board port has the system disk connected.) I was having Disk #4 fail consistently, so I tried swapping the cables on the controller end. I swapped the on-board RAID disk with one on the PCI controller. Same issue now, expect with disk #1. Once the system's up, I can reactivate the RAID, it will resync for a while, then go to "Healthy", and will stay that way for an indefinite amount of time - until I reboot. As soon as I reboot, the disk drops again. I've ruled out disk + cable with the recabling. I don't believe it would be the controller as it seems to work fine most of the time - only failing on reboot, and the other port on the same controller connects the system disk - which is clearly working. I did look in the event log, but didn't see anything particularly relevant (although I didn't know what I was looking for - just looked for anything with a "Warning" or "Error" symbol that looked disk-related :)). I'm not particularly familiar with RAID on Windows, does anyone have any idea why this might be doing this? Any idea how to fix it? Any suggestions appreciated! -- Adam

  Read the article

• Why am I seeing Zero errors in non-ECC RAM?

  - by Alexander Shcheblikin

  According to sources, memory errors are a very probable event: Some say the probability of a DRAM error is 95% in just 3 days of operation of a computer with just 4 GB of RAM, others say 32% of servers experience at least one error in a month with 8% of DIMMs being at fault. Contrary to those horrors, in my more than 10 years of personal computers use I have seen exactly none of the memory errors. I admit I never paid special attention to the subject. However, I have ventured multi-hour memtest86 runs couple of times and never seen an error either. Some of the factors that IMO should aggravate the memory problems: I build my computers out of the most "bulk commodity" parts: mainstream budget motherboards and the next to cheapest memory. also I usually max out the technology available, e.g. in the times of 32 bit OS'es I used 4 GB of RAM and with the current desktop CPUs and the newer 64 bit OS'es I use 32 GB of RAM. memory usage is moderately heavy with lots of virtual machines up running small and big tasks 24/7/365. But nevertheless, no memory-related problems ever found! How's that?

  Read the article

• Windows freezes when watching videos

  - by cornerback84

  I have Acer laptop Aspire 5740 - 5780 with windows 7 Ultimate 32 bit. I am using Chrome. Windows is 1 year old, but it's not the first time this has happened. Windows freezes whenever I am watching videos on facebook/youtube or when using SopCast. I thought there was some faulty plugin, so I recently re-installed chrome but it happened again. No keys work, and the sound of whatever I am listening starts repeating like grrrr..drrrr. Its seems like the sound in very slow motion. One time I left it in this freeze state for 5 min and it recovered automatically. It usually does not happen when I am using windows media player. I had some codecs installed but I removed them to see if that fixes. So far, I have narrowed it down to youtube/footytube videos and sopcast. I have checked event logs but nothing special. Is there any way I can narrow down the problem or any suggestions on how to fix it. I'd like to add that it does not always happen. Sometimes windows goes days/weeks without freezing, and sometimes it take a min into video to freeze.

  Read the article

• Installing Ubuntu guest crashes Hyper-V host

  - by Grant

  I have a weird problem that I don't even know where to begin diagnosing. Trying to install Ubuntu to a VM locks up the host system! My setup is: Dell R715 server, dual 16 core AMD opteron processors, 96GB RAM Dell MD3600f SAN Server 2008 R2 Datacenter System Center VMM 2012 There are 5 windows virtual machines running that have had no problems. This is the first linux VM I've tried to create. I setup a VM through virtual machine manager, set the CD drive to a Ubuntu 12.04 server x64 iso, and started it up. It boots up the normal ubuntu install menu, but the second I hit enter on "Install Ubuntu Server", I get disconnected. The HOST machine stops responding to pings. So do all virtual machines on it. It locks up entirely - keyboard on the host won't work, mouse won't move, numlock light won't change. There's no blue screen - the host is sitting at the login screen completely unresponsive. I can't find any relevant logs in event viewer after rebooting. What could cause the host machine to freeze like that? It's not a one time occurrence - it happens every time at the exact same point. Thank god this server isn't in production yet!

  Read the article

• sysbench memory test on ec2 small instance

  - by caribio

  I'm seeing a problem with sysbench memory test (the default version that's compiled in). This is on Ubuntu Maverick, sysbench installed via apt-get install sysbench. Running the same thing on Ubuntu @ Rackspace worked just as expected. While the CPU and I/O tests worked fine on EC2 servers, the memory test just runs without doing anything (notice the 0M in the test results). The instance used was the publicly available 'stock' Ubuntu image with no changes to it: ./ec2-run-instances ami-ccf405a5 --instance-type m1.small --region us-east-1 --key mykey Supplying more arguments (such as: --memory-block-size=1K --memory-total-size=102400M) didn't help. What am I doing wrong? Thanks. sysbench --num-threads=4 --test=memory run sysbench 0.4.12: multi-threaded system evaluation benchmark Running the test with following options: Number of threads: 4 Doing memory operations speed test Memory block size: 1K Memory transfer size: 0M Memory operations type: write Memory scope type: global Threads started! Done. Operations performed: 0 ( 0.00 ops/sec) 0.00 MB transferred (0.00 MB/sec) Test execution summary: total time: 0.0003s total number of events: 0 total time taken by event execution: 0.0000 per-request statistics: min: 18446744073709.55ms avg: 0.00ms max: 0.00ms Threads fairness: events (avg/stddev): 0.0000/0.00 execution time (avg/stddev): 0.0000/0.00

  Read the article

• How can I automatically synchronize a directory tree on multiple machines?

  - by Blacklight Shining

  I have two Mac laptops and a Debian server, each with a directory that I would like to keep in sync between the three. The solution should meet the following criteria (in rough order of importance): It must not use any third-party service (e.g. Dropbox, SugarSync, Google whatever). This does not include installing additional software (as long as it's free). It must not require me to use specific directories or change my way of storing things. (Dropbox does this IIRC) It must work in all directions (changes made on /any/ machine should be pushed to the others) All data sent must be encrypted (I have ssh keypairs set up already) It must work even when not all machines are available (changes should be pushed to a machine when it comes back online) It must work even when the /directories/ on some machines are not available (they may be stored on disk images which will not always be mounted) This can be solved for Macs by using launchd to automatically launch and kill (or in some way change the behavior of) whatever daemon is used for syncing when the images are mounted and unmounted. It must be immediate (using an event-based system, not a periodic one like cron) It must be flexible (if more machines are added, I should be able to incorporate them easily) I also have some preferences that I would like to be fulfilled, but do not have to be: It should notify me somehow if there are conflicts or other errors. It should recognize symbolic and hard links and create corresponding ones. It should allow me to create a list of exceptions (subdirectories which will not be synced at all). It should not require me to set up port forwarding or otherwise reconfigure a network. This can be solved by using an ssh tunnel with reverse port forwarding. If you have a solution that meets some, but not all of the criteria, please contribute it in the comments as it might be useful in some way, and it might be possible to meet some of the criteria separately. What I tried, and why it didn't work: rsync and lsyncd do not support bidirectional synchronization csync2 is designed for server clusters and does not appear to work with machines with dynamic IPs DRBD (suggested by amotzg) involves installing a kernel module and does not appear to work on systems running OS X

  Read the article

• Users are getting a temporary profile

  - by Serhiy

  A bit about current setup: It is windows 2008 R2 AD servers (all of them are 2008R2) and couple locations which set as Sites. Each location has DFS on AD server. Roaming profiles are not used nor configured. Users have their home folder configured as mapped S: drive to DFS shared folder. For example: in profile tab user has: Home Folder - connect - S: to \\domain.com\dc\users\%username% We also have redirected Desktop, Documents and Downloads folders to \\domain.com\dc\users. Everything was fine. Suddenly (today), users in most locations lost their local profile (both XP and W7 desktops) and got temporary profiles. Also, it looks like local profile was created today (from folder properties). I checked events at couple machines and there is not errors related to profiles or logon process. I do not see issues in event logs at servers as well. Basically, I run out of ideas what is wrong and why machines lost their local profiles. PS: Laptop users do not have their folders redirected, but lost profiles as well.

  Read the article

• windows 7 monitor instantly resumes from power off

  - by user167328

  It seems that some service or program is preventing my monitor from going into power save mode but I cannot find a way to dig down the cause. Does anybody know a way to find out which event may be causing the problem? Background information: If I leave/lock my computer I want to immediately power off the monitor. Stupid windows has no program for this so I use a third party utility. I use Display.exe from Noel Danjou since 2005 and have had no problem with it on XP, my Notebook with w7 x64 pro and at the office with w7 x64 enterprise. With my new home pc with w7 x64 pro the monitor goes off but instantly comes back on after a second. So I tested using a power plan with the shortest timeout of 1 minute but with that the display never goes off at all. (Setting a power plan timeout is no useful option because then I cannot read a document or watch a movie without the monitor going off) I could try trial and error methods but this is cumbersome and not what I regard as a professional solution. So I would prefer a way to analyze the windows events to find out the reason for the display staying active. Add On: In the meantime I tried safe mode and also exited from all tray programs but the problem is still there. I also checked the BIOS for special power settings but still no solution (P.S. Mobo is H87-G41 PC Mate with latest BIOS rev.)

  Read the article

• System Center 2012 VMM UI is very slow

  - by Grant

  I've recently setup system center 2012 a new server 2008 r2 server which I'm using for virtual machines. Everything seems to be working fine, and the virtual machines are nice and fast. But the Virtual Machine Manager interface is always excruciatingly slow. Sometimes taking up to 15 seconds moving between screens. It's very frustrating trying to use it when a task that just involves a couple clicks ends up taking several minutes. Pages that have a lot of form fields seem to take the longest to load - such as the page to change hardware settings of a virtual machine. Is this just normal performance for VMM? If not, where can I look to find what is slowing it down. Nothing else on the system seems to suffer. I can load and use Hyper-V manager with no noticable slowness. Even programs like event viewer that are usually rather slow seem to load fairly fast. Only the system center programs seem slow. Server is a Dell R710, 2x16 core opteron 6274 processors, 96GB RAM. OS drive is 2x500GB 7.2k RPM SAS drives in RAID1 (opted for the less expensive 7.2k drives since pretty much everything is stored on the SAN). Am I just being impatient? Does anyone else use VMM 2012 and find it slow?

  Read the article

• do I need to create an AD site for VPN network

  - by ykyri

  I have Windows Domain level 2008 R2. There are four GC DC in four different physical locations. I have Kerio-based VPN network for replication and remote administration. Here is how network configured: dc1: local IP: 192.168.0.10 VPN IP: 192.168.1.10 dc2: local IP: 10.10.8.11 VPN IP: 192.168.1.11 dc3: local IP: 10.10.9.12 VPN IP: 192.168.1.12 dc4: local IP: 10.10.10.13 VPN IP: 192.168.1.13 That's simple, replication and all works fine but when running dcdiag on dc3 I have an error: A warning event occurred. EventID: 0x000016AF During the past 4.12 hours there have been 216 connections to this Domain Controller from client machines whose IP addresses don't map to any of the existing sites in the enterprise. <...> The log(s) may contain additional unrelated debugging information. To filter out the needed information, please search for lines which contain text 'NO_CLIENT_SITE:'. The first word after this string is the client name and the second word is the client IP address. Here is netlogon.log lines example: 05/30 12:07:39 DOMAIN.NAME: NO_CLIENT_SITE: dc2 192.168.1.11 05/31 09:52:11 DOMAIN.NAME: NO_CLIENT_SITE: dc4 192.168.1.13 05/31 19:49:31 DOMAIN.NAME: NO_CLIENT_SITE: adm-note 192.168.1.101 07/01 05:16:26 DOMAIN.NAME: NO_CLIENT_SITE: dc1 192.168.1.10 All VPN-joined computers are generates same log line as above. Computer amd-note is for example administrator's notebook, also have VPN. Question is should I add new AD site and bind VPN subnet 192.168.1.0/24 with that site?

  Read the article

• KVM Hosting: How to efficiently replicate guests

  - by javano

  I have three KVM servers each with 1 guest VM, running directly on it's local storage, (so they are essentially getting a dedicated box worth of computing power each). In the event of a host failure I would like the guests replicated to at least one of the other hosts so I can spin it up there, until the failing host is fixed. I am curious about KVM cloning. I can clone a VM live or when it's suspended/shutdown. Obivously suspended VMs will naturally be quicker to clone but these three VMs comprise three parts of a single solution, so I don't want to ever have any one of them shutdown. How can I efficiently clone these VMs between servers? I have had a couple of ideas, but are these insane or, is there a better method I have missed for my scenario? Set up a DRDB partition between box 1 and 2 where VM 1 runs from, and so is replicated between box1 and box 2, repeat between box 2 & 3, and box 3 & 1 (This could be insane, I have never used DRDB only read about it) Just use standard KVM CLI clone options to perform live clones (I'm dubious about this because I don't know how long it will take and what the performance impact will be during) Run a copy of each VM on at least one other host, and have the guest on one host export it's data to the matching guest on another host where it can import that data, scripting this on the guest) Some of other way? Ideas welcome! Side Note These servers have 4x15k SAS drives in a RAID 10 so they aren't rocketing fast, and as I mentioned, each VM runs from the host's local storage, no NAS or SAN etc. So that is why I am asking this question about guest replication. Also, this isn't about disaster recovery. Guests will be exporting their data to a NAS over a VPN, so I am looking at how I can have them quickly spun up in a host failure situation.

  Read the article

• Problem running “Central Administration” website after windows update at Windows 2003 Server Standar

  - by Magdy Roshdy

  I was have WSS 2.0 and then I upgraded to WSS 3.0 and the old instalation database was SQL 2000, now I have another SQL Server instance called:server_name\MICROSOFT##SSEE . After upgrade every thing works fine and our team started to use the portal and we sent lot of documents and make lot of activities on it. The problem started after installing Windows updates the website suddenly stopped and giving me an error "Cannot connect to the configuration database" If I tried to open SharePoint Products and Technologies Configuration Wizard it is gives me a strange error says: "An exception of type Microsoft.SharePoint.PostSetupConfiguration.PostSetupConfigurationTaskException was thrown. Additional exception information: SharePoint Products and Technologies cannot be configured. The current installation mode does not support SKU to SKU upgrades because there exists an older version of Windows SharePoint Services that must be upgraded first " At this post:http://stackoverflow.com/questions/114398/iis-error-cannot-connect-to-the-configuration-database/249494#249494 the guy of the second answer have the same problem and he suggested a solution but I don't understand well. I tried as he suggested to make the identity of the app pool of the SharePoint web site as "IWAM_server_name " after that the error changed as he said and I web site give me "Server Application Unavailable " and when checked the Event Viewer at the server I found that ASP.NET 2.0 give this exception: "Could not load file or assembly 'System.Web, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a' or one of its dependencies. Access is denied ." and I don't know how to solve this problem. I'm really want to make my web site working because our team really need these documents and its stuff. I hope I will find some one to help me.

  Read the article

• Diagnose remote desktop freezes in Windows 7 when no BSOD?

  - by Paul Smith

  Okay, I'm getting no joy from Asus or Microsoft on this, so hoping for some clues on how to narrow down the cause. I have very frequent OS freezes, always & only when running Remote Destkop Client (mstsc) in Windows 7 x64. I never have a bluescreen, and there is never a minidump. The display & input just freezes -- no keyboard, no mouse, and sound will just continue the last wavelength if any. So far, I can't find a way to trap the hang given that there's no bluescreen; advanced startup & recovery settings for system failure are "Write an event" checked, "Automatically restart" checked, and "Kernel memory dump". I've updated to the lasted BIOS, and tried a few different graphics drivers, both generic & ATI. I've also tried disabling Aero, and everything about the remote desktop experience (incrementally unchecked every box in the mstsc - options - experience tab), even disabled/unplugged external monitor to make sure it wasn't a dual-monitor issue. My specs are: Asus G73jh notebook 8GB RAM ATI Mobility Radeon HD 5800 Series graphics (recently tried driver versions 8.791.0.0, 8.801.0.0) American Megatrends G73jh.211 BIOS (7/27/2010) Windows 7 Home Premium x64 Windows Memory Diagnostic passed all of the following at least 3 times with no errors: MATS+ INVC LRAND Stride6 WMATS+ WINVC This notebook is better than most at removing heat (laudable vent design), so I'm not inclined to suspect thermal causes (especially since running 1080p video for hours has never caused a freeze, but mstsc does, reliably, within 5 minutes to an hour). This did seem to start happening after a Windows Update, but I've since reverted every patch applied since a week before the first occurrence, with no joy. (And I'd only had the PC for a couple weeks before that, so it could have been chance + less actual time spent remoting at the beginning.) I'm at my wits end, and I bought this laptop primarily as a remote terminal client (go figure, right?) Any ideas on how to identify the cause of this? Thanks!

  Read the article

• Explorer.exe hangup during move large file into external drive

  - by PiotrK

  During move large files (700mb+) to external drive formated NTFS via USB 3.0 I've noticed strange things about explorer.exe (I am using Windows 7 up to date) Sometimes after move file the explorer get stuck (ie. it can happen after few files during move of several large files) - moving window freeze and I am unable to kill explorer (via taskmgr, or cmdline TASKKILL). In command line I've got something like this (taskmgr shows that explorer.exe is still running - I've got the same PID every time I try to kill it and no diagnostic message): C:\Windows\system32TASKKILL /F /IM explorer.exe SUKCES: proces "explorer.exe" o identyfikatorze PID 6296 zostal zakonczony. C:\Windows\system32TASKKILL /F /IM explorer.exe SUKCES: proces "explorer.exe" o identyfikatorze PID 6296 zostal zakonczony. If I try to run another explorer.exe process at this point, I got desktop icon and start bar back but I cannot open any explorer window After few minutes explorer.exe finally dies and I am able to rerun it without rebooting File that I moved have two copies - one local and one on the external drive (the original file wasn't delete after move); Both copies seems to contain the same data (same length and CRC info) If this happen during move of multiply files, only some files are moved and one of them have two copies (both locally and on the external drive) What can I do to fix those explorer hangs? Added: The same problem exist when copying files, it hangsup between large files Similar problem exist when I tried to use TotalCommander (x64): copying paused at 80% of one of files, TC didn't hung up (but clicking cancel in copying dialog box doesn't have any effect). During this pause I can't kill TotalCmd.exe just like Explorer.exe Added (2): This problem seems to disappear when I use 32 bit applications (like TotalCommander (x86) ), but I need to do more testing to be sure of this Added (3): There are several errors in event log, source: disk, id: 11, qualifiers: 49156, task: 0, level: 2, keywords: 0x80000000000000 (This may be important, and I forgot to mention this): Main disk is encrypted via Truecrypt (boot-in password)

  Read the article

• xen + debian network after upgrade squeeze to wheeze

  - by rush

  I've got a Debian + Xen server. After a system upgrade to the stable version the network doesn't come up after boot. Every time after reboot I need to bring it up manually. The network configuration was not changed during upgrade. Here is /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 11.22.33.44 netmask 255.255.255.0 gateway 11.22.33.1 nameserver 8.8.8.8 After boot ip r shows no route and eth0 has no ip address. Manually ip and route setup goes fine and network starts working. Messages from dmesg about network I've found (looks like nothing interesting) [ 3.894401] ACPI: Fan [FAN3] (off) [ 3.894444] ACPI: Fan [FAN4] (off) [ 4.178348] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c9 [ 4.178351] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 4.178392] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: 0100FF-0FF [ 4.178413] e1000e 0000:02:00.0: Disabling ASPM L0s L1 [ 4.178432] xen: registering gsi 16 triggering 0 polarity 1 -- [ 4.223667] ata5: DUMMY [ 4.223668] ata6: DUMMY [ 4.289153] e1000e 0000:02:00.0: eth1: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c8 [ 4.289155] e1000e 0000:02:00.0: eth1: Intel(R) PRO/1000 Network Connection [ 4.289245] e1000e 0000:02:00.0: eth1: MAC: 3, PHY: 8, PBA No: 1000FF-0FF [ 4.506908] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 4.542920] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) -- [ 10.362999] EXT4-fs (dm-23): mounted filesystem with ordered data mode. Opts: (null) [ 10.419103] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null) [ 10.988255] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 13.175533] Event-channel device installed. [ 13.287555] XENBUS: Unable to read cpu state -- [ 13.288670] XENBUS: Unable to read cpu state [ 13.965939] Bridge firewalling registered [ 14.134048] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 14.283862] ADDRCONF(NETDEV_UP): peth0: link is not ready [ 14.284543] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 17.800627] e1000e: peth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 17.801377] ADDRCONF(NETDEV_CHANGE): peth0: link becomes ready [ 18.307278] device peth0 entered promiscuous mode [ 24.538899] eth1: no IPv6 routers present [ 28.570902] peth0: no IPv6 routers present I've upgraded two servers and I've such behaviour on two of them. How to fix this and get network starts automatically on boot?

  Read the article

• Microsoft Word "Random" Crashes

  - by Bent Rasmussen

  Word seemingly randomly crashes in an application setting where it is first being used to programmatically databind (bookmarks) and then directly afterwards opened on the user machine for further user input. The error message is quite precise but the workaround has eluded me. Word crashes a moment or two after it has been opened on the user machine with the below exception details. Problem signature: Problem Event Name: APPCRASH Application Name: WINWORD.EXE Application Version: 14.0.6129.5000 Application Timestamp: 5082f354 Fault Module Name: wwlib.dll Fault Module Version: 14.0.6129.5000 Fault Module Timestamp: 5082f3dc Exception Code: c0000005 Exception Offset: 000eed32 OS Version: 6.1.7601.2.1.0.16.7 Locale ID: 1030 Additional information about the problem: LCID: 1030 skulcid: 1030 Sometimes one can run the exact same scenario 50 times before experiencing a crash, other times only a few times. We have tried using different versions of the Word format as well as renaming the databound file after saving so that the file being opened on the user machine is different. Principally Word should never crash but perhaps there is some workaround that can make Word not crash. Googling for a solution there appears to be multiple things that can trigger this bug.

  Read the article

• Application Pool Identity corruption

  - by Gavin Osborn

  I have observed a few times while deploying software into IIS that every now and again the related Application Pools fail to restart and in the Event Log we see an error like the following: The identity of application pool, 'AppPoolName' is invalid. If it remains invalid when the first request for the application pool is processed, the application pool will be disabled. This does not happen frequently but when it does the only solution is to re-apply the Identity password in the IIS Manager Window. As soon as I re-apply and then restart the application pool the web sites come back up. Facts: The account is a service account whose password never expires. The account is local to the IIS host. The account password is never changed. This is IIS 6 running on Windows Server 2003 Deployment of the software is via MSI and involves several IIS Resets. The software is created in house and does not do anything fancy to IIS. Any ideas how the identity information might become corrupt? Edit: Clarification To be clear - this user account and password combination work absolutely fine and usually works fine as the Identity of the Application Pool. It is only when we deploy updates of our software into an existing IIS application that it stops working. Our password has not changed Our deployment does not change the password or reconfigure the application pools. This does not happen every time, 1/20 times perhaps. If we re-enter the password into IIS and restart the App Pools everything works.

  Read the article

• hyper-v cluster behavior when losing network connectivity

  - by ChristopheD

  Setup: (rather new) Hyper-V R2 cluster with 2 nodes (in failover configuration). Fysical host OS: Windows Server 2008. About eight VM's (mixed: Windows Server 2008 and Linux) Yesterday we had a power outage of about 15 minutes. Our blades are on UPS so the fysical host machines (Windows Server 2008) never went down. Our main switches are not on UPS (yet) and we saw the behaviour similar to the following (as distilled from the event logs). The nodes in the cluster lost means of communication (because the external switches went down). The cluster wants to bring down one (the first) of the nodes (to start failover?). The previous step impacts clustered storage where the virtual machine VHD's are located. All VM's got brutally terminated and were found in a failed state in the failover manager in the host OS'es. The Linux VM's were kernel panicking and looked like they had their disk ripped out. This whole setup is rather new to us, so we are still learning about this. The question: We are putting switches on UPS soon but were wondering if the above is expected behavior (seems rather fragile) or if there are obvious improvements configuration-wise to handle such scenario's ? I can upload an evtx file concerning what exactly was going on in case that's necessary.

  Read the article

• What can I do to determine the root cause of a Windows server hanging/freezing?

  - by Aaronaught

  We set up a new server here a few weeks ago that I am informally responsible for managing. Almost everything works perfectly except for one thing: Every so often it hangs without warning. To clarify: When I say hangs, I mean completely. None of the services respond and I'm unable to even get onto a local console - the display acts as though there's no VGA signal. One time, the server actually responded to pings, another time I got the "destination host unreachable" response, but most of the time the pings just time out, as one would expect for a hung server. Event logs don't show anything after a reboot. I don't mean that they don't show anything interesting, I mean that they don't show anything at all from before the failure occurs to after the reboot. And there are never any performance problems, strange errors, or other obvious signs of impending doom before it happens. I don't expect any easy answers here. What I'd like to know his I can methodically determine the root cause of this problem, be it a misbehaving service, defective hardware, or something else. Is there any kind of logging I can set up that will help me get to the bottom of this? Any hardware diagnostics or remote monitoring? Anything else I can do to help me discover what's actually happening, or at least be able to eliminate what isn't wrong? Just to reiterate, I really don't want to start speculating about possible causes and take a trial-and-error approach, because it's going to be at least several days at a time before I would have conclusive results. I'm looking for solutions to reliably trace the problem to its source.

  Read the article

• Google Drive terminates without error on startup

  - by Iszi

  I've used Google Drive for awhile now, but it won't start up after installing on my latest system re-build. I'm still using the same OS, hardware, and basic software load (antivirus, firewall, etc.) that I have for years during which I had not previously had problems with Drive. OS: Windows 7 Ultimate x64 Google Drive Version: 1.12.5329.1887 Now, whenever I try to run Google Drive, it just spawns two instances of the executable which die shortly after. No error messages are posted to the desktop, and nothing indicating any problem is written to the Event Log. After some research, I've yet to find anyone having the same problem who's found an answer. I did find out how to run Google Drive in diagnostic mode, using the --vv parameter at the command line. After that, I opened up the sync log and got this: 2013-10-31 17:11:24,039 INFO pid=3664 1892:MainThread logging:1600 OS: Windows/6.1.7601-SP1 2013-10-31 17:11:24,039 INFO pid=3664 1892:MainThread logging:1600 Google Drive (build 1.12.5329.1887) 2013-10-31 17:11:24,039 DEBUG pid=3664 1892:MainThread logging:1608 DEBUGGING DUMP is ON. 2013-10-31 17:11:24,051 ERROR pid=3664 1892:MainThread logging:1575 ERROR, UNEXPECTED EXCEPTION 2013-10-31 17:11:24,051 ERROR pid=3664 1892:MainThread logging:1575 [Error 5] Access is denied Traceback (most recent call last): File "<string>", line 232, in Main File "<string>", line 118, in RegisterCustomFileTypes File "P:\p\agents\hpal4.eem\recipes\353983091\base\b\drb\googleclient\apps\webdrive_sync\windows\build\pyi.win32\main\outPYZ1.pyz/windows.registry", line 62, in GetValue WindowsError: [Error 5] Access is denied 2013-10-31 17:11:24,052 INFO pid=3664 1892:MainThread logging:1600 Crash reporting disabled. Ignoring report. 2013-10-31 17:11:24,052 INFO pid=3664 1892:MainThread logging:1600 Exiting with error code: 0 I'm running on an account with Administrator-level permissions, and have even tried using "Run As Administrator" on the EXE. I'm not sure why it's looking for a P:\ drive, as no such volume has ever been mounted on this system. What should I do to try to further troubleshoot, and resolve, this issue?

  Read the article

• Need help toubleshooting PC

  - by brux

  I have had problems since my dog pee'd on my computer. Problem: loads windows fine, at random intervals from 5 minutes to 30 minutes it restarts itself. There is nothing in the event log such as errors, no BSOD, just cold restart. after restarting - sometimes- it POST's and restarts itself at the end of POST. It will do this many times and then finally load windows. The cycle then begins again, it will restart eventually. What I have done: I thought it was HDD at first, since this is the only part of the computer which actually got wet with any fluid ( the case is off the PC and the dog pee'd down the front where the HDD is located). Seatool, the seagate HDD tool, found errors when I ran it inside windows, so I ran it in DOS mode from boo-table USB and ran it. It found the same number of errors and fixed them all. I ran the scan again and it says "Good". I loaded windows and ran the scan and it also said "Good there. So the HDD appears to be fine but the problem persists, random restarts. What else could this be? I have taken the computer apart and cleaned everything and also taken the PSU apart and cleaned it thoroughly. The problem still persists, what should my next steps be?

  Read the article

• Connection timed out on Node.js app running under CentOS

  - by ss1271

  I followed this tutorial to create a simple node.js app on my CentOS: the node.js version is: $ node -v v0.10.28 Here's my app.js: // Include http module, var http = require("http"), // And url module, which is very helpful in parsing request parameters. url = require("url"); // show message at console console.log('Node.js app is running.'); // Create the server. http.createServer(function (request, response) { request.resume(); // Attach listener on end event. request.on("end", function () { // Parse the request for arguments and store them in _get variable. // This function parses the url from request and returns object representation. var _get = url.parse(request.url, true).query; // Write headers to the response. response.writeHead(200, { 'Content-Type': 'text/plain' }); // Send data and end response. response.end('Here is your data: ' + _get['data']); }); // Listen on the 8080 port. }).listen(8080); However, when I uploaded this app onto my remote server (assume the address is 123.456.78.9), I couldn't get access to it on my browser http://123.456.78.9:8080/?data=123 The browser returned Error code: ERR_CONNECTION_TIMED_OUT. I tried the same app.js code which runs fine on my local machine, is there anything I am missing? I tried to ping the server and its address was reachable. Thanks.

  Read the article

• download and process a file by ftp at set intervals, with error handling, rescheduling and status messages

  - by compound eye

  I want to download a data file from a remote ftp server to my machine at regular intervals. Once the file is downloaded I want to call another script which will process the file. My development machine is mac os x, the eventual deployment environment is linux. What's would be the stock standard way to automate this? I know I can use cron to schedule curl to download and to run a script that will process the downloaded file at regular intervals, and I know could write a slightly more complex script or an application that would do this and add error handling, rescheduling and sending status emails. But one of my requirements for this project is to write as little custom code as possible, instead I should try to use standard, tried and true existing tools, and if I do have to write code, to try and write the most straightforward code possible. The reason for this is the code will potentially be installed on a large number of machines, all of which will need to be tweaked, customised and maintained by different people, long after I am gone from the project, so the intention is to use well documented, well supported tools as much as possible. This seems such a common task, there must be tools and scripts all over the internet, written by people who have carefully considered everything that could possibly go wrong when you need to download and process a file from a remote server at regular intervals, with error handling, rescheduling and sending status messages. Is that what Expect is for? What would you recommend? (the system will be downloading weather prediction data every six hours, so that the system can prepare in the event of bad weather warnings)

  Read the article

• Connecting to Server 2008 shares fails

  - by Chris J

  I'm having problems getting a reliable share working on an x64 Server 2008 R1 SP1 server. All works well after a reboot, but after some time (within a day) the shares become unavailable to XP and Server 2003 servers. Interestingly, they remain available to other Server 2008 servers. On trying to access \\server\share, Server 2003 returns immediately and simply gives me the message "The specified network name is no longer available", XP takes a minute or two to timeout before giving the same message. There doesn't seem to be anything in the event logs indicating a problem. Doing some googling over the last day or two I've seen the following blamed: Bad network drivers ... I've updated to the latest drivers with no result Symantec anti-virus ... we're not using it (currently no AV on the server) Receive window auto-tuning ... I've disabled with netsh int tcp set global autotuninglevel=disabled and netsh int tcp set global rss=disabled None of these have had an effect. Windows Firewall is currently disabled. As other Server 2008 boxes (both x32 and x64) can connect, I can only assume that there's some new security configuration that's not quite right - or there's an AD issue that I need to trace, but don't know where to start. Even if anyone doesn't know how to resolve, if someone knows what I need to look for with Wireshark this would be a help.

  Read the article

• Access is denied when running batch file on Windows7

  - by Radek

  I have a bat file on Windows7 that I used to run. Now I am not able to run it because of Access is denied error. My account is part of administrator group. C:\EduTester\others>mysqlbackup.bat Access is I am able to see the file via more mysqlbackup.bat when inside the directory where the file sits. C:\EduTester\others>more mysqlbackup.bat @echo off rem settings etc etch In fact I used to run the bat file as administrator using runas command runas /savecred /user:yogurt\administrator "c:\EduTester\others\mysqlbackup.bat" Attempting to start c:\EduTester\others\mysqlbackup.bat as user "yogurt\administrator" ... RUNAS ERROR: Unable to run - c:\EduTester\others\mysqlbackup.bat 2: The system cannot find the file It used to run ok few days ago. I am not aware that I would change something that could affect this. I have just tried to restart the Windows7 computer and I am experiencing the same. UPDATE In event viewer I can see this Windows cannot load the user's profile but has logged you on with the default profile for the system I think it might the be cause...

  Read the article

< Previous Page | 512 513 514 515 516 517 518 519 520 521 522 523  | Next Page >