Search Results

Search found 21942 results on 878 pages for 'internet friend'.

Page 516/878 | < Previous Page | 512 513 514 515 516 517 518 519 520 521 522 523 | Next Page >

How to set up IP forwarding on Nexenta (Solaris)?

- by Gleb

I am trying to set up IP forwarding on my Nexenta box: root@hdd:~# uname -a SunOS hdd 5.11 NexentaOS_134f i86pc i386 i86pc Solaris The box has 2 network interfaces: root@hdd:~# ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 e1000g1: flags=1001100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4,FIXEDMTU> mtu 1500 index 2 inet 192.168.12.2 netmask ffffff00 broadcast 192.168.12.255 ether 68:5:ca:9:51:b8 myri10ge0: flags=1100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4> mtu 9000 index 3 inet 10.10.10.10 netmask ffffff00 broadcast 10.10.10.255 ether 0:60:dd:47:87:2 lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1 inet6 ::1/128 192.168.12.0 is my normal LAN with 192.168.12.1 being the firewall/gateway 10.10.10.0 is a separate LAN for iSCSI (with no internet access) I want to set up IP forwarding so that a computer on 10.10.10.0 will be able to access the internet by using 10.10.10.10 as a gateway (I don't need any port forwarding) I have turned on IP forwarding: root@hdd:~# routeadm Configuration Current Current Option Configuration System State --------------------------------------------------------------- IPv4 routing disabled disabled IPv6 routing disabled disabled IPv4 forwarding enabled enabled IPv6 forwarding disabled disabled Routing services "route:default ripng:default" Routing daemons: STATE FMRI disabled svc:/network/routing/rdisc:default disabled svc:/network/routing/route:default disabled svc:/network/routing/legacy-routing:ipv4 disabled svc:/network/routing/legacy-routing:ipv6 disabled svc:/network/routing/ripng:default online svc:/network/routing/ndp:default But when I dry to start ipnat, I get an error: root@hdd:~# ipnat -CF -f /etc/ipf/ipnat.conf ioctl(SIOCGNATS): I/O error Here is the config: root@hdd:~# cat /etc/ipf/ipnat.conf #!/sbin/ipnat -f - # map e1000g1 10.10.10.10/24 -> 192.168.12.2/32 So the question is how to fix this.. Thanks in advance!

Read the article
Opening and Testing Ports on Modem > Router Connection

- by JakeTheSnake

Working off of my last question, I can access my server's FTP over the LAN but not over the internet. I'm using Filezilla on port 666. My router/modem configuration is as such (similar to other post): 1) Modem connects to WAN 2) WAN port on modem connects to LAN port on Router 3) Modem internal IP address is 192.168.0.254 4) Router internal IP address is 192.168.0.1 5) Modem has DHCP turned OFF 6) Router has DHCP turned ON 7) Router is running Tomato firmware and it's set as 'Router' (not 'Gateway') 8) The internet is working (just had to say that) I've set up port forwarding both on the modem and router - both route port 666 to the IP address of 192.168.0.3 (TCP); that is the IP address of the server which has FileZilla running. I don't know if that's hindering anything but I've also tried it with just the modem and just the router...same result. I've also tried setting the server to be DMZ (both on router and modem). Neither router nor modem have anything in their logs about denying inbound traffic on port 666 so my ability to troubleshoot stops there. I've tried contacting my ISP (Telus, running on mobility plan...it's a "Smart" Hub) but they weren't much help. They said they only block port 25 and 80 and maybe a few others, but not most ports. I test whether or not the port is open by going to canyouseeme.org - I don't know whether or not that would produce a 'connection refused' result just based on the fact that the FTP requires a login...I'm not well versed on this matter. FWIW, sometimes I get a 'connection refused' error on canyouseeme.org but mostly it's 'connection timed out'. I don't know what else to do at this point.

Read the article
Configure Domino to use SMTP routing and hMailServer

- by Sébastien Lachance

I have been trying for a couple of days to set up a Domino 8.5 server. Basically, I want everything to be run inside a local network. Right now I can send email to other user in the Domino directory without any mail address. I am pretty new to all this stuff, so maybe the answer will be really obvious. What I need to do is be able to send a mail from somewhere else to a domino user that will be redirected to his account. On the Domino server, I also have hMailServer installed on port 25. I configured Domino to use port 26. I followed those step to get where I am now. -I have set the Fully qualified Internet host name to "preview.notes". -Smtp Listener task changed to Enabled to turn on the Listener so that the server can receive messages routed via SMTP routing -Setting up SMTP routing within the local Internet domain (http://www.h2l.com/help/help85%5Fadmin.nsf/f4b82fbb75e942a6852566ac0037f284/7f9738a49efc4f58852574d500097b01?OpenDocument) -I modified the person to use the [email protected] address. -I'm using the hMailServer (which have the local "preview.local" domain name) to send mail to [email protected]. When sending mail I got an error telling that the DNS is not set up correctly. Is using the Domino Smtp server instead of hMailServer will solve the problem? I can Telnet the Domino Smtp Server.

Read the article
Using bind (named) as a public proxy server

- by TrentDavis

We have a Python DNS server that does a bunch of stuff to figure out values it should return for various DNS records. This works nicely, however as it is Python, the performance under high load won't be great. What I would like to do is have a "proxy" bind server sit in front of it to return results to the public internet. This will cache the results (typically 15 minutes, some records are a few seconds), so the load on the Python server will be greatly reduced as it will only see one look up per domain (only about 100 domains) every 15 minutes. The data in these domains changes a lot, so using a master won't work as it will constantly be changing. I have something setup that looked like it would work great (using a forwarder for the zone), and tested it with dig etc, all going great. However when we went to go live with it, things weren't working, and we figured out that named is not setting the "Authoritative" bit (fair enough, it is a forwarder). So my question is, can we tell bind to set the Authoritative bit for forwarded domains? I have looked at all the doco I can find, and can't find anything about doing things this way. Most of the doco about using it as a proxy if for a LAN to the internet. Ideally I would like to use bind as it is there and installed (CentOS 5 servers). But at a pinch we could look at a different name server to do the work if it just can't be done with bind. Thanks.

Read the article
rdesktop over ssh

- by Dan

In Ubuntu, I'm trying to log into my friend's windows machine using rdesktop. First, I can log into his outward facing linux box using ssh. Then from there I can log into his linux host machine using ssh. This host machine is running Windows XP inside virtualbox. Is there a way for me to tunnel rdesktop through these two ssh connections (may just need the first connection to the outward facing linux box just to get inside the network, depending on how virtualbox's network connection is set up). Thanks

Read the article
RRAS NAT not working on a certain computer

- by legenden

This is driving me crazy. I have a virtualized W2K8 server running RRAS. Every other computer or server on the network can access the internet through the NAT except one. On one server, it just won't work. I can ping the ip address of the NAT gateway just fine, and everything else works. (SMB, etc) DNS, which is hosted by the same server, also works just fine. I have even reinstalled the OS on the problem server and it still doesn't work. Recap of the steps I tried: There are 3 network cards in the server, I tried every one and different switch ports. Not a hardware problem. Reinstalled W2K8 R2 on server with the problem, didn't help. Tried the IP of the internet gateway directly - this did work (!). But I need NAT to work. All firewalls are disabled. Removed computer from domain, deleted computer membership in Active Directory Users and Computers and added it back. Disabled all other network adapters and set a static ip and specified the gateway ip manually. When I tracert a public IP, the first hop (or any other hop) comes up as: C:\>tracert www.google.com Tracing route to www.l.google.com [209.85.225.106] over a maximum of 30 hops: 1 * * * Request timed out. 2 * * * Request timed out. From a different computer, on which NAT works, the first hop comes up as: tracert www.google.com Tracing route to www.l.google.com [209.85.225.105] over a maximum of 30 hops: 1 <1 ms * <1 ms xxxx [10.5.1.1] This is the most bizarre problem I ever came across, and I realize that it's a long shot asking it here given all the details, but I'm pulling my hair out. Maybe someone has an idea...

Read the article
IT lead does not have a backup, DR plan in writing

- by Alex

This is a general management question to IT managers out there. We are a small firm with about 4 servers in our colo cabinent. No full time IT manager. But we do have one person on monthly contract and I am having a terrible time getting him to share what these plans actually are. I am sure he HAS a plan (and its probably in his head..) but that does us no good if he gets hit by a bus.. How would you guys handle this? He is a long time friend, but I fear this is dangerous for us long term..I have confronted him on several occasions about this, and he tells me not to worry, he has go it covered.. Thanks.

Read the article
Issue resolving names on Hyper-V guest with Routing and Remote Access

- by John Sheehan

I've got a Win2k8 standard server running Hyper-V with a Server 2003 web guest instance running. The host is publicly available on the internet. I've created an Internal Private network in the Hyper-V Virtual Network manager. I've set the host IP for that virtual adapter to 192.168.0.1. I've set the IP on the guest to 192.168.0.2. They can ping each other and share files. I can't browse the web on the guest though. NSLOOKUPs are working. I've tried setting the DNS server setting on the guest to 192.168.0.1 and something external like Google's 8.8.8.8 server to no avail. Windows firewall is disabled on the internal virtual network. I've tried it with both DNS installed on the host and without it. I'm not sure which RRAS/NAT settings are relevant to pass on so ask if you need me to clarify anything. How do I get outbound internet working on the guest VM?

Read the article
Wireless router blocking some sites while using ethernet is fine

- by Micke

I'm using Windows 7 and my router is a wireless Apple Airport Express that is approximately two years old. Suddenly I can't access some sites (for example www.sthlm.friskissvettis.se, or www.vegetarian-shoes.co.uk, some streamed tv-shows on svtplay.se, and a number of other random sites) when connecting to internet with my router. It worked good until recently and I'm fairly sure this problem emerged when my ISP upgraded from 10/10mbit to 100/10mbit speed. Most other sites like facebook and google works fine. When using my network cable to connect to internet everything works fine and I can access these sites. Firmware is current and I've tried reseting the router to factory defaults. Tried different browsers, and I can't ping the "blocked" sites either. Tracert www.sthlm.friskissvettis.se starts with 10.0.0.1 and continues through a number of long addresses until it says timeout. The last working address before timeout was sth-tcy-ipcore01-ge-0-2-0.neq.dgcsystems.net [83.241.252.13], if it matters. Tracert www.vegetarian-shoes.co.uk also eventually gives me a timeout. When the network cable is plugged in, I still get timeout on tracert www.sthlm.friskissvettis.se even though I can access the site in Chrome. Weird. www.vegetarian-shoes.co.uk doesn't give me a tracert timeout when the cable is plugged in, and I can access the site as usual. I've tried changing DNS servers to use opendns servers instead, but to no use. I've tried pinging these two sites with a lower MTU packet size (with this method: http://www.richard-slater.co.uk/archives/2009/10/23/change-your-mtu-under-vista-or-windows-7/), but still can't access them through ping... I don't know what to do anymore.... any suggestions???

Read the article
Windows 7 wireless not seeing any networks

- by jkohlhepp

I think I have managed to confuse Windows 7. When I did the install, I had the network cable plugged in to my router, but the wireless card was also enabled. During the install, Windows 7 seemed to see my wireless network and even asked me for the WEP key. I know that it used the WEP key because I initially entered an invalid one and it gave me an error. Then the network said "SoAndSoWireless Connected". However, when I unplug or disable my wired network card, then I have no internet, and it can't see any networks. When I plug in the wired network card, it says "SoAndSoWireless Connected". Under Network and Internet Network Connections I have "Local Area Connection" and "Wireless Network Connection". The wired one's status is "SoAndSoWireless" and the wireless status is "Not Connected". Also, the wireless connection can't seem to see any other wireless networks in the area and I know there are tons. My neighbors have several. I've somehow seemingly confused Windows 7 into thinking that my wired network card is my wireless card or something. Any ideas on how to un-confuse it? This is a desktop machine by the way, if it matters. EDIT: Ah, I think part of the problem is that I named my network accidentally the same as the name of the wireless network being broadcast by the wireless router. So that might be why it says that name on the hard-wired connection. Perhaps the drivers just are completely not working for the wireless card. Thanks, ~ Justin

Read the article
2 nics. 2 Defaults Gateways

- by andre.dias

Here is my scenario: i have this server with 2 nics, each one with different IPs, connected to differents routers. Almost everything is configured whe way i need. Traffic coming from eth0 exits using eth0, traffic coming from eth1 exits using eth1. And there is a default gateway configured. $route: default IP 0.0.0.0 UG 0 0 0 eth0 With this configuration, the traffic generated in the server is going out using eth0 (lynx www.google.com for example). The problem is: the Internet link from eth0 went down today. The traffic coming from eth1 was ok...no problem. But the traffic generated in the server was a problem...the default gateway was out...no access do the Internet anymore (no more lynx www.google.com) So i added a new default gateway configuration, pointing to eth1. For 30 minutes i kept that way...2 default gateways, but just one was "working"...and everything was working just fine. But then i removed de eth0 gateway entry because, well, 2 default gateways is kind of weird. My question: is there any problem on keeping these 2 default gateways, one for each? So i don´t need to do nothing when one link go down again? $route: default IP1 0.0.0.0 UG 0 0 0 eth0 default IP2 0.0.0.0 UG 0 0 0 eth1

Read the article
Setting up a laptop hard drive as a secondary on a tower?

- by vermiculus

I'm trying to install Windows 8 for a friend who has recently bricked a laptop hard drive. The new one is OEM so there is no OS - I need to be able to stick it in to my tower and load the new OS on it. Both bricked and replacement laptop hard drives are SATA and connect to my mobo just like any other. After I post this I'm going to check the BIOS and see if it shows up, but so far I don't have it showing up in Disk Management. Any ideas would be greatly appreciated.

Read the article
Change which server mailbox is associated with in Exchange 2007

- by tacos_tacos_tacos

I have restored and mounted an EDB file onto a new Exchange 2007 Server. However, the old server is still online and although all the mailboxes I need are in the newly-mounted database, in Exchange 2007 System Manager it still shows that the mailbox is associated with the old server. If I try to "Move" the database it actually tries to copy the files from the old server to the new server, which is not necessary because they are already there - and produces and error about the mailbox on the destination already existing. How can I simply tell Exchange (AD?) to use the new server to find the mailbox rather than the old? Edit: I did the restore by taking the old server offline (turning off all Exchange services), copying EDB file to the new server, restoring it with eseutil, and mounting it to the new server. I did it this way in part because I didn't know a better way and in part because I couldn't use move-mailbox as the source location had a horrible Internet connection (which is why Exchange is being moved to the new location). I had to copy the EDB from the old server to a hard disk, go somewhere with a better Internet connection, upload the EDB to the new server.

Read the article
Software available for singing "lessons" via computer microphone?

- by drozzy

Looking for a software to help my friend learn to sing. Can't seem to find anything on googles. Does there exist software (preferably downloadable and from this century!) that records one's voice and then analyzes it to see how "accurate" it was. It would be great if it also had some kind of "lessons" of some sort, and not simply sound recorder that shows waveforms. I can't imagine it would be so hard to implement, and there probably is one out there - I just can't find it. Any recommendations are welcome. Thanks.

Read the article
What is polarity for an unmarked USB hub?

- by Feral Oink

On my USB hub where the power supply plugs in, the polarity is unmarked (I got it used, from my brother's friend). I need to know what the polarity should be. I don't think it makes a difference about the brand. Could someone who has a USB hub tell me what the polarity markings are? This is why I need to know about the polarity: Usually the center pin is positive and the outer pin is negative. But I'm not sure with this, and want to be certain before I plug anything into it.

Read the article
NAT ports - how do they work?

- by Davidoper

I have the following network schema: Computer A: three nics: NIC 1 (eth0): dhcp, public internet NIC 2 (eth1): static 192.168.1.1, gateway for Computer B NIC 3 (eth2): static 192.168.2.1, gateway for Computer C Computer B: static 192.168.1.2, using gateway 192.168.1.1 (NIC 2). Computer C: static 192.168.2.2, using gateway 192.168.2.1 (NIC 3). So I applied this to get NAT working: iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE Every computer can connect to the internet now. I have been applying rules to the main computer (Computer A), like dropping connections to some ports, e.g ssh: iptables -A INPUT -p tcp --dport 22 -j DROP But for instance, now I would like only allow connections for ports 20,21,22,53 and 80 in Computer C, and ignore the outside traffic if it's not related to those ports. The allowed connections should be FROM Computer C to outside, but not from outside to Computer C (I mean - Computer C is not hosting any HTTP or SSH, but it is going to use them as a client). I guess this sould be done like this: iptables -A OUTPUT -i eth2 -o eth0 -p tcp --dport 21 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i eth2 -o eth0 -p tcp --sport 21 -m state --state ESTABLISHED -j ACCEPT The last rule (dropping any other traffic different from those) is at the end of the configuration, so -A should be working correctly. The thing is... it is not working. If I put the last rule like this: iptables -A FORWARD -i eth2 -o eth0 -j DROP It just drops everything and, for instance, port 21 (previously opened as you can see above) is not either working. Can you tell me what could I have done wrong? I have been struggling with this problem for some time and I am unable to solve it. Thanks!

Read the article
SSRS 2005 inaccessible after install

- by Gabriel Guimarães

Hi I've just installed SQL 2005 and Database Engine is ok, however I can't access it for nothing. When I go to http://localhost/reports I get this prompt for a username and password and it fails with 401.1. When I tried to disable kerberos on the virtual directories, nothing changed. I've tried changing the auth to anonymous and get: Internet Explorer cannot display the webpage. When I access from another machine, I get the prompt only once and get this error. Internet Explorer cannot display the webpage. Can't access this with IE or SSMS 2005. If I try to access with Management Studio i get this error: TITLE: Microsoft SQL Server Management Studio The underlying connection was closed: An unexpected error occurred on a receive. (Microsoft.SqlServer.Management.UI.RSClient) ADDITIONAL INFORMATION: Unable to read data from the transport connection: An existing connection was forcibly closed by the remote host. (System) An existing connection was forcibly closed by the remote host (System) BUTTONS: OK By the way the server info: its a Win 2003 R2 Standard with IIS 6 Can't seem to understand this. Does anyone have a hint?

Read the article
Ubuntu 12.04 Netinstall URL? Xen Host

- by notFound

Well I have an Xen server, I've got a CentOS container up fine but a friend of mine wants (oh god) Ubuntu Server 12.04, why he can't use Debian is beyond my understanding. But anyways, I can't remember how I installed the CentOS container but I'm giving virt-manager a try now, since I don't have a disk image already the only option is to get a Network Install URL since I'm using PV. So does anyone know what I should type in there, if it was CentOS I could easily type http://mirror.centos.org/centos/6.2/os/i386 for example. The furthest I've got in finding a suitable URL is http://archive.ubuntu.com/ubuntu/dists/precise/ but that of course wont work. Any ideas?

Read the article
Merge only a one remote branch into a local branch with Mercurial

- by Pepijn

I wan to manage some profiles as XML files in Mercurial repos. The setup I'm thinking of: Each user has a repo with a branch where he manages his own profile, and a number of branches where he can pull and merge other profiles from that branch of another user. So for example I have my own profile branch and a branch labeled friends, in which I want to pull the profile branches of a few remote repos, to collect like a collection of profiles. I figured out that since the repos are unrelated I need to use -f, but I can't figure out how to pull and merge only a single branch into another. So I want like me friend someone profile ---> friends <--- profile \-> family friends <--- profile Is this even possible? Should I use separate repos instead? Is there a better solution?

Read the article
Overriding routes on Openvpn client, iproute, iptables2

- by sarvavijJana

I am looking for some way to route packets based on its destination ports switching regular internet connection and established openvpn tunnel. This is my configuration OpenVPN server ( I have no control over it ) OpenVPN client running ubuntu wlan0 192.168.1.111 - internet connected if Several routes applied on connection to openvpn from server: /sbin/route add -net 207.126.92.3 netmask 255.255.255.255 gw 192.168.1.1 /sbin/route add -net 0.0.0.0 netmask 128.0.0.0 gw 5.5.0.1 /sbin/route add -net 128.0.0.0 netmask 128.0.0.0 gw 5.5.0.1 And I need to route packets regarding it's destination ports for ex: 80,443 into vpn everything else directly to isp connection 192.168.1.1 What i have used during my attempts: iptables -A OUTPUT -t mangle -p tcp -m multiport ! --dports 80,443 -j MARK --set-xmark 0x1/0xffffffff ip rule add fwmark 0x1 table 100 ip route add default via 192.168.1.1 table 100 I was trying to apply this settings using up/down options of openvpn client configuration All my attempts reduced to successful packet delivery and response only via vpn tunnel. Packets routed bypassing vpn i have used some SNAT to gain proper src address iptables -A POSTROUTING -t nat -o $IF -p tcp -m multiport --dports 80,443 -j SNAT --to $IF_IP failed in SYN-ACK like 0 0,1 0,1: "70","192.168.1.111","X.X.X.X","TCP","34314 > 81 [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=18664016 TSER=0 WS=7" "71","X.X.X.X","192.168.1.111","TCP","81 > 34314 [SYN, ACK] Seq=0 Ack=1 Win=5792 Len=0 MSS=1428 TSV=531584430 TSER=18654692 WS=5" "72","X.X.X.X","192.168.1.111","TCP","81 > 34314 [SYN, ACK] Seq=0 Ack=1 Win=5792 Len=0 MSS=1428 TSV=531584779 TSER=18654692 WS=5" "73","192.168.1.111","X.X.X.X","TCP","34343 > 81 [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=18673732 TSER=0 WS=7" I hope someone has already overcome such a situation or probably knows better approach to fulfill requirements. Please kindly give me a good advice or working solution.

Read the article
BGP Multipath & return routes

- by Dennis van der Stelt

I'm probably a complete n00b concerning serverfault related questions, but our IT department makes a bold statement I wish to verify. I've searched the internet, but can find nothing related to my question, so I come here. We have Threat Management Gateway 2010 and we used to just route the request to IIS and it contained the ip address so we could see where it was coming from. But now they turned on "Requests apear to come the TMG server" so ip addresses aren't forwarded anymore. Every request has the ip of the TMG server. Now the idea behind this is that because of multipath bgp routes, the incoming request goes over RouteA, but the acknowledgement messages could return over RouteB. The claim is that because the request doesn't come from the first known source, our proxy, but instead from IIS, some smart routers at the visitor of our websites don't recognize the acknowledgement message and filter it out. In other words, the response never arrives. Again, this is the claim. But I cannot find ANY resources on the internet that support this claim. I do read about bgp multipath, but more in the case that there are alternative routes when the fastest route fails for some reason. So is the claim completely bogus or is there (some) truth to it? Can someone explain or point me to resources? Thanks in advance!

Read the article
VPN to Buffalo WHR-HP-G300N produces a Connection Error 807

- by Darius

My friend has modem/router from Clear and I have sent him Buffalo router to put it between his Clear device and the Network. I walked him thru establishing VPN in DD-WRT but when I try to VPN I get a VPN Connection Error 807. I am out of ideas how to solve this. Any suggestion? Clear Modem WAN: xx.xx.xx.xx Clearn Modem NAT's to: 192.168.15.XXX Clear Modem DHCP: 192.168.15.2 - 192.168.15.2 (range is limited to that of ONE ip address) Clear Modem DMZ: 192.168.15.2 the LAN of the clear modem is 192.168.15.XXX The DD-WRT IP: 192.168.4.1 Port FWD: 1723 to 192.168.4.1 PPTP server listens on 192.168.4.1 Where is the problem with this setup?

Read the article
Running a Check-Disk (Is it dangerous)

- by vaccano

I have a lap top that a friend of mine would like me to fix. It is giving a blue screen on boot up. When I looked up the error message it indicates that I should run a check disk. Is this dangerous? Should I try to off load stuff from the hard drive first? I ask because I had a hard drive of my own that when I ran check disk it wiped a bunch of "bad sectors" and I lost most of the info on it (but it had been going bad). Opinions?

Read the article
How to set up QoS on ADSL router (terracom) for prioritizing browsing

- by DBZ_A

I want to configure the ADSL router which connects 10+ machines to the internet. I want to give maximum priority to browsing (ports 80,443) and set low priority for bittorrent etc.(port 42180) I have been experimenting with settings , but with no luck. There are three settings which confuse me, along with my understanding. 802.1 Priority - Related to LAN level, possible values 0-7 , higher numbers means higher priority. 'Mark traffic priority' - clueless about this. IPP/DS - IP Precedence - possible values 0-7 ; 6 & 7 are reserved, so set 5 for highest priority. Or when using DSCP - set 46 for highest priority. Please help me in getting this done... Similer question for another model of router here , but with less number of confusing options :) How to configure QoS on home router Update: from discussion on another thread, QoS can control only upstream traffic (from router to the internet) , while this may in turn affect downstream traffic rate, there is no direct control over data coming into the router.

Read the article
Her microphone produces white noise, after a while?

- by Wolfpack'08

When my friend Skypes with me or gets on FB Video with me, her sound works fine... at first. After a bit, it starts sounding like loud static. It happens more frequently as we restart video chats, until it happens as soon as we open video chats. We usually restart her PC to fix the issue. Is there a process we could kill, maybe? Skip that question, if you will, and jump to these two: How do we fix this? Why is this happening?

Read the article

< Previous Page | 512 513 514 515 516 517 518 519 520 521 522 523 | Next Page >