Search Results

Search found 21942 results on 878 pages for 'internet friend'.

Page 517/878 | < Previous Page | 513 514 515 516 517 518 519 520 521 522 523 524  | Next Page >

  • Cisco Catalyst 3750 connected to Cisco ASA 5505 and dropping packets

    - by Bo102010
    (Cross posted from Super User per suggestion there) At the office, I have inherited a network that I am still trying to fully comprehend. I have a problem today with a new connection between: A port on a Cisco Catalyst 3750 [WS-C3750G-48TS-S running C3750-IPSERVICESK9-M version 12.2(53)SE1] A port on a Cisco ASA 5505 [ASA Software version 8.3(2)] The 3750 is home to a Vlan that has a few ports assigned to it. interface Vlan3 description Internal network (172.18.160.0/24) ip address 172.18.160.1 255.255.255.0 I have a host (outside of my control) that needs to be in this VLAN (i.e it must have an address 172.18.160.something/24) that also needs to access the Internet. To accomplish this, I ran a link from the Catalyst (Gi1/0/13) to the ASA (Ethernet 0/5). I configured the Catalyst port like so: interface GigabitEthernet1/0/13 description To ASA, 172.18.160.69 switchport access vlan 3 switchport mode access speed 100 duplex full I configured the ASA like so: interface Vlan1 nameif inside security-level 100 ip address 172.18.160.69 255.255.255.0 interface Ethernet0/5 speed 100 duplex full Then I plugged the host into Ethernet 0/4 on the ASA and instructed its owner to make its default gateway 172.18.160.69. I made a NAT rule in the ASA and set up some rules, and it's able to access the Internet without issue. However, I noticed that the Catalyst reports a ton of packets being dropped toward the ASA. Catalyst3750#show interfaces GigabitEthernet 1/0/13 | include counters|drops Last clearing of "show interface" counters 00:28:13 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 136909347 This is a huge number of drops, since there's not much traffic on this VLAN at all. I tried these things: Make sure speed and duplex agree on both sides (100 Mbps / Full) Set no cdp enable on the Catalyst Gi10/13 Set no keepalive on the Catalyst Gi10/13 Checked for excessive CPU usage on both Checked for excessive traffic on both Am I missing something? Any help would be appreciated.

    Read the article

  • What keeps you from changing your public IP address and wreak havok?

    - by Whitemage
    An interesting question was asked to me and I did not know what to answer.. So I'll ask here. Let's say I subscribed to an ISP and I'm using cable internet access. ISP gives me a public IP address of 60.61.62.63. What keeps me from changing this IP address to, let's say, 60.61.62.75 and mess with another consumer's internet access? For the sake of this argument, let's say that this other IP address is also owned by the same ISP. Also, let's assume that it's possible for me to go into the cable modem settings and manually change the IP address. Under a business contract where you are allocated static addresses, you are also assigned a default gaetway, a network address and a broadcast address. So that's 3 addresses the ISP "loses" to you. That seems very wastefull for dynamically assigned IP addresses where the majority of customers are.. Could they simply be using static arps? ACLs? Other simple mechanisms? Anyone who worked at an ISP would be willing to explain this a bit?

    Read the article

  • Can not connect to tomcat server externally,

    - by KItis
    My Tomcat server is running on virtual server, this server is running on fedora machine. I have setted up everything on this machine to run tomcat, tomcat working well on local host. but i can not access the wsdl of the webservice running on this tomcat server remotely using IP address of this server, as follows. http://xxx.xxx.xxx.xxx:8080/axis2/services/listServices one of my friend said that i need to configure DNS to access remotely using IP address, i didn't understand what he said also. iptables on this server is also stooped. Also , i can access mysql running on this server remotly, my problem is why doesn't it work for tomcat. could someone can help me to find a solution for this problem. Thanks in advance for any help

    Read the article

  • How can I setup apache+mod_proxy so when I connect to mod_proxy on interface X, it sends the traffic

    - by aspitzer
    We use a service that allots us X number of requests per IP and has allows us to setup 5 IPs with such a limit (I know.. it seems stupid they could not just up the limit 5x on one IP). Pretend I have a linux box with the following address on the internet: 66.249.90.104 - that is an Google IP and not mine... so feel free to try to hack into it :) I setup apache+mod_proxy as a forwarding proxy (ProxyRequests On). i.e. you can setup firefox to use 66.249.90.104:8080 as a proxy, and all firefox traffic comes out as 66.249.90.104. So far so good. Problem: Now I add more alias interfaces so the total looks like this: eth0: 66.249.90.104 eth0:1 66.249.90.105 eth0:2 66.249.90.106 eth0:3 66.249.90.107 eth0:4 66.249.90.108 I run apache+mod_proxy (single apache instance) which binds to all interfaces, but no matter which address I connect to use the forwarding proxy, all traffic goes out to the internet as 66.249.90.104 I have also tried running 5 different apaches, each binding to its own interface only, but that still sends the outbound request through 66.249.90.104. I was hoping to get it to work as follows: I connect to 66.249.90.108 and make a proxy request, and it goes out as 66.249.90.108. I connect to 66.249.90.107 and make a proxy request, and it goes out as 66.249.90.107. etc. Has anyone else had to deal with this issue? The fall back solution would be to just run apache on 5 separate boxes, but I would prefer it to all work on one box. Thanks!

    Read the article

  • Replacing local home server with VPS: Suggestions?

    - by CamronBute
    So right now, I'm running an old box with a 2TB HDD in it. I use this as a file server for the home network, as well as a box for downloading large files which are synced via Dropbox. Lots of other tinkering things, too. Basically, I'm sick of paying extra for the power and having to worry about drive failures and whatnot. I'd rather get a remote server, let someone else manage it and provide access from the Internet. So, I've been looking for a Windows VPS that would give me access to install things and tinker, and I'm having a problem finding a host that offers more than 100GB of hard drive space. If they do offer a package with 100GB of storage, everything else is waaayyyy more than what I actually need. The idea is to create a permanent VPN connection from the cloud server to my home network to provide a transparent solution so I'm not having to go to lengths to transfer files or whatnot. I think a VPS solution will allow me to do this. I would like 1TB of storage space, minimum 100Mbps Internet connection, minimum 250GB bandwidth, admin access. Anyone have anything? Or am I being unreasonable? If I am, why?

    Read the article

  • Network share not always available on Windows 2003

    - by JP Hellemons
    Hello everybody, we have a windows 2003 server with a shared directory/folder. I've seen this thread but this wasn't any help: http://superuser.com/questions/58890/the-specified-network-name-is-no-longer-available I have a ping -t running from 3 pc's (vista and two windows 7) they all work. the problem occurss when two users enter the network share then this 'network share is no longer available' appears and the explorer windows turn white. after f5 or refresh the shared directory is back. this is really strange. there is no anti virus or kasparsky running on either end. this is all in the same LAN. the internet connection is really stable, so it's really strange. because a stable internet connection should imply that the local network connection is also stable and that this is a windows issue. can it be a router issue? I have checked the eventlog on the server for diskfailure related messages, but there are none. EDIT: can this be related to mapping a shared directory to a drive letter? and that there is a router between me and the mapped network drive? or is it just windows that is not working well with two users on the same shared folder? should I install samba or something?

    Read the article

  • How to connect 2 routers (Asmax and D-link) RJ11 vs RJ45 issue

    - by piobyz
    I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

    Read the article

  • MP3 player no longer syncs after installing Sixaxis drivers

    - by zildjohn01
    I recently installed third-party drivers for the (Sony) PS3 controller on my friend's PC (Windows XP). I found out a few days later that his MP3 player (also Sony) is no longer recognized by Windows. He gets the "connect device" sound, and about 250ms later, the "disconnect device" sound. I figured the controller driver took over the Walkman's device ID, so I went through the registry and C:\Windows\inf removing all references to Sony's VID (054C), but I haven't had any luck. What would you do in this situation?

    Read the article

  • Cannot Get Sound Over HDMI in Windows 7

    - by Aayush
    Windows 7 has been really good to me, I never needed to install any drivers & that included sound. Win7 took care of all that, but because of that I don't have any extra controls. Just the native Windows sound controls. I connected my LCD and PC using the HDMI, works great with video but the sound seems to stick with the PC speakers. My friend somehow solved this in Vista, but to port the sound to the LCD, he always had to restart the computer, which I found really weird and never made me interested to even know how he did that. There has to be way to do this easily. Please let me know if anyone else had the same problem & solved it somehow. Thanks!

    Read the article

  • Improving abysmal 802.11n wireless network

    - by concept
    I am in desperate need of help to improve the abysmal performance of my 802.11n wireless network. At best I get 30Mbs (this is an internet download) from a technology that boasts 300Mbs, even worse is the LAN where to date best i have ever gotten is 1Mbs. It is literally quicker to copy the file to a USB and walk it to the other computer. Infrastructure is this AP 802.11n only broadcasting at both 2.4GHz and 5GHz Mac with 802.11a/b/g/n card is connected to the AP via 5GHz Linux with 802.11a/b/g/n card is connected to AP via 2.4GHz I have conducted the following tests (results at end of post) Internet based speed test wired and wireless LAN file copy wired and wireless I have read: http://nutsaboutnets.com/troubleshooting-wi-fi-problems/ http://www.smallnetbuilder.com/wireless/wireless-basics/30664-5-ways-to-fix-slow-80211n-- speed http colon //www.wi-fiplanet dot com/tutorials/7-tips-to-increase-wi-fi-performance.html Slow file transfer on network between two 802.11n laptops (connected directly together via access point) Wireless Network Performance Issues Slower than expected 802.11n wireless network speeds I have made the following optimizations AP broadcasts only 802.11n on both 2.4GHz and 5GHz frequencies 2.4GHz is on a channel with least interference (live in an apartment with lots of APs), this did make a 10Mb/sec improvement Our AP is the only one transmitting on the 5GHz freq. Security: WPA Personal WPA2 AES encryption Bandwidth: 20MHz / 40MHz (i assume this to be channel bonding) I have tried the following with 0 improvement Dropped the Fragment Threshold to 512 Dropped the Request To Send (RTS) Threshold to 512 and 1 Even thought of buying a frequency spectrum analyzer, until i saw the cost of them!!! Speed test results Linux Wired: DOWNLOAD 128.40Mb/s UPLOAD 10.62Mb/s www dot speedtest dot net/my-result/2948381853 Mac Wired: DOWNLOAD 118.02Mb/s UPLOAD 10.56Mb/s www dot speedtest dot net/my-result/2948384406 Linux Wireless: DOWNLOAD 23.99Mb/s UPLOAD 10.31Mb/s www.speedtest dot net/my-result/2948394990 Mac Wireless: DOWNLOAD 22.55Mb/s UPLOAD 10.36Mb/s www.speedtest dot net/my-result/2948396489 LAN NFS 53,345,087 bytes (51Mb) file Linux Mac NFS Wired: 65.6959 Mb/sec Linux Mac NFS Wireless: .9443 Mb/sec All help is appreciated, even testing methods will be accepted.

    Read the article

  • How to connect 2 routers (Asmax and D-link) RJ11 vs RJ45 issue

    - by piobyz
    I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

    Read the article

  • How to connect 2 routers (Asmax and D-link) RJ11 vs RJ45 issue

    - by piobyz
    I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

    Read the article

  • Something very strange with network

    - by Rodnower
    Hello, I have Windows 7 and I have very strange thing with my network. Some time I was connected through wireless router and my IP was 192.168.2.103, router's IP was 192.168.2.1 and some other IP was 192.168.2.100. The last I get from page "active DHCP clients" of web interface of the router and from "wireless clients" I may to see that 192.168.2.100 not (!) belong to my MAC address. Router build by EDimax. So after that I disabled wireless function of the router and restarted it. In this time I had not ping to 192.168.2.1. Also I had not any other connection, not wireless nor cable, but (!) I still had ping to 192.168.2.100 and I not understand what this voodoo is... C:\Users\Andrey>ping 192.168.2.100 Pinging 192.168.2.100 with 32 bytes of data: Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Ping statistics for 192.168.2.100: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms This is what I had: C:\Users\Andrey>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : Andrey-PC Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Wireless LAN adapter Wireless Network Connection 3: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Virtual WiFi Miniport Adapter #2 Physical Address. . . . . . . . . : 06-1D-7D-40-61-EB DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Wireless LAN adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Gigabyte GN-WS50G (mini) PCI-E WLAN Card Physical Address. . . . . . . . . : 00-1D-7D-40-61-EB DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Controller Physical Address. . . . . . . . . : 00-1B-24-B6-09-91 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes C:\Users\Andrey>arp -a -v Interface: 127.0.0.1 --- 0x1 Internet Address Physical Address Type 224.0.0.22 static 239.255.255.250 static Interface: 0.0.0.0 --- 0xffffffff Internet Address Physical Address Type 192.168.2.1 00-0e-2e-d2-8c-af invalid 192.168.2.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Interface: 0.0.0.0 --- 0xffffffff Internet Address Physical Address Type 192.168.2.1 00-0e-2e-ff-f1-f6 dynamic 192.168.2.101 00-27-19-bc-8b-9c dynamic 192.168.2.102 00-16-e6-6c-ae-d4 dynamic 192.168.2.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Interface: 0.0.0.0 --- 0xffffffff Internet Address Physical Address Type 224.0.0.22 01-00-5e-00-00-16 static 255.255.255.255 ff-ff-ff-ff-ff-ff static C:\Users\Andrey>route print =========================================================================== Interface List 14...06 1d 7d 40 61 eb ......Microsoft Virtual WiFi Miniport Adapter #2 13...00 1d 7d 40 61 eb ......Gigabyte GN-WS50G (mini) PCI-E WLAN Card 11...00 1b 24 b6 09 91 ......Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Controller 1...........................Software Loopback Interface 1 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 1 306 ff00::/8 On-link =========================================================================== Persistent Routes: None Only after reboot I lost ping to there: C:\Users\Andrey>ping 192.168.2.100 Pinging 192.168.2.100 with 32 bytes of data: PING: transmit failed. General failure. PING: transmit failed. General failure. PING: transmit failed. General failure. PING: transmit failed. General failure. Ping statistics for 192.168.2.100: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), So what this mysterious cache is? Thank you for ahead.

    Read the article

  • Pinging an external server through OpenVPN tunnel doesn’t work

    - by qdii
    I have an OpenVPN server and a client, and I want to use this tunnel to access not only 10.0.8.0/24 but the whole internet. So far, pinging the server from the client through the tun0 interface works, and vice versa. However, pinging www.google.com from the client through tun0 doesn’t work (all packets are lost). I figured that I should configure the server so that any packet coming from tun0 in destination of the internet be forwarded, so I came up with this iptables config line: interface_connecting_to_the_internet='eth0' interface_openvpn='tun0' internet_ip_address=`ifconfig "$interface_connecting_to_the_internet" | sed -n s'/.*inet \([0-9.]*\).*/\1/p'` iptables -t nat -A POSTROUTING -o "${interface_connecting_to_the_internet}" -j SNAT --to-source "${internet_ip_address}" echo '1' > /proc/sys/net/ipv4/ip_forward Yet, this doesn’t work, the packets are still lost and I am wondering what could possibly be wrong with my setup. Some details: ip route gives on the server: default via 176.31.127.254 dev eth0 metric 3 10.8.0.0/24 via 10.8.0.2 dev tun0 10.8.0.2 dev tun0 proto kernel scope link src 10.8.0.1 127.0.0.0/8 via 127.0.0.1 dev lo 176.31.127.0/24 dev eth0 proto kernel scope link src 176.31.127.109 ip route gives on the client: default via 192.168.1.1 dev wlan0 proto static 10.8.0.1 via 10.8.0.5 dev tun0 10.8.0.5 dev tun0 proto kernel scope link src 10.8.0.6 127.0.0.0/8 via 127.0.0.1 dev lo scope link 192.168.1.0/24 dev wlan0 proto kernel scope link src 192.168.1.109 client uses wifi adapter wlan0 and TUN adapter tun0. server uses ethernet adapter eth0 and TUN adapter tun0. the VPN spans on 10.0.8.0/24 both client and linux are using Linux 3.6.1.

    Read the article

  • Debian/OVH: How to configure multiple Failover IP on the same Xen (Debian) Virtual Machine?

    - by D.S.
    I have a problem on a Xen virtual machine (running latest Debian), when I try to configure a second failover IP address. OVH reports that my IP is misconfigured and they complaint they receive a massive quantity of ARP packets from this IPs, so they are going to block my IP unless I fix this issue. I suspect there's a routing issue, but I don't know (and can't find any useful info on the provider's website, and their support doesn't provide me a valid solution, just bounce me to their online - useless - guides). My /etc/network/interfaces look like this: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address AAA.AAA.AAA.AAA netmask 255.255.255.255 broadcast AAA.AAA.AAA.AAA post-up route add 000.000.000.254 dev eth0 post-up route add default default gw 000.000.000.254 dev eth0 # Secondary NIC auto eth0:0 iface eth0:0 inet static address BBB.BBB.BBB.BBB netmask 255.255.255.255 broadcast BBB.BBB.BBB.BBB And the routing table is: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 000.000.000.254 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 0.0.0.0 000.000.000.254 0.0.0.0 UG 0 0 0 eth0 In these examples (true IP addresses are replaced by fake ones, guess why :)), 000.000.000.000 is my main server's IP address (dom0), 000.000.000.254 is the default gateway OVH recommends, AAA.AAA.AAA.AAA is the first IP Failover and BBB.BBB.BBB.BBB is the second one. I need both AAA.AAA.AAA.AAA and BBB.BBB.BBB.BBB to be publicly reachable from Internet and point to my domU, and to be able to access Internet from inside the virtual machine (domU). I am using eth0 and eth0:0 because due to OVH support, I have to assign both IPs to the same MAC address and then create a virtual eth0:0 interface for the second IP. Any suggestion? What am I doing wrong? How can I stop OVH complaining about ARP flood? Many thanks in advance, DS

    Read the article

  • where to look for computer technician jobs

    - by Kareem
    Hi I am currently studying for the A+ certification, I plan to have it by the end of this month and I plan to go for farther education. I’ve built two high end computers by myself for a friend and family member. Install OS and everything. I’m looking in to finding either a computer assembly or computer technician job . Where is the best place to look for one? I’ve looked in to best buy but I find their geek squad to be a little bit shady. Where is a good place to look for a full time entry level computer technician job just starting out in Tampa, FL?

    Read the article

  • Question about domain name registration

    - by Obay
    I received the following email from a certain [email protected] YYY is a company name ZZZ is OUR company name Dear Manager, We are a professional intellectual property rights consultant organization, mainly deal with the global domain name registration and internet intellectual property rights protection. On March. 24th, 2010, we formally received an application from YYY, they applied to register the internet brand “ZZZ” and some relevant domain names with our organization. During our preliminary investigation, we found that these domain names' keyword is fully identical with your trademark. Therefore, we need to confirm with you, whether you consigned YYY to register these domain names with us or not? Or, is YYY your business partner or distributor? If you have no relationship with this company, we assume that they have other purposes to obtain these domain names. Currently, we have already suspended this company's application temporarily due to the seriousness of this isuue. In order to avoid the vicious domain name grabbing, please let the relevant person make a confirmation with me via telephone or email as soon as possible. Thank you for your support to our work! Best Regards XXX Tel: xxxxx-xxxx xxxx Fax: xxxxx-xxxx xxxx Email: [email protected] www.world-wtc.cn This seems legit, or is it? By the way, XXX is just a first name, not a complete name.

    Read the article

  • Ubuntu-VirtualBox-LikeWiseOpen network disaster

    - by Sergio
    I've a virtual machine on VirtualBox 4.1.4 with Ubuntu 11.04. It was working perfectly, but after a reboot something really wrong happened: I wasn't able to connect to the internal network (same for NAT). $ sudo dhclient -v Internet Systems Consortium DHCP Client 4.1.1-P1 Copyright 2004-2010 Internet System Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Error creating socket to list interfaces; Permission denied Can't get list of interfaces. The network interface is PCnet-FAST III. Additional information: $ uname -a Linux LinuxFileServer 2.6.38-8-generic #42-Ubuntu SMP Mon Apr 11 03:31:50 UTC 2011 i686 i686 i386 GNU/Linux Any ideas? Thanks EDIT: $ sudo ifconfig -a eth1 Link encap:Ethernet HWaddr 08:00:27:af:f2:c7 indirizzo inet6: fe80::a00:27ff:feaf:f2c7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:16 errors:0 dropped:0 overruns:0 carrier:0 collisioni:0 txqueuelen:1000 Byte RX:0 (0 B) Byte TX:3870 (3.8 KB) Interrupt:10 lo Link encap:Loopback locale indirizzo inet:127.0.0.1 Maschera:255.0.0.0 indirizzo inet6: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:16 errors:0 dropped:0 overruns:0 frame:0 TX packets:16 errors:0 dropped:0 overruns:0 carrier:0 collisioni:0 txqueuelen:0 Byte RX:960 (960.0 B) Byte TX:960 (960.0 B)

    Read the article

  • Limiting bandwith on an Windows 7 machine

    - by Mihai Damian
    I need to limit the bandwidth on my Windows 7 x64 machine. In the past (on XP) I've been able to use NetLimiter for similar tasks. However for some reason I can't get it to work anymore. For lower limits the bandwidth tests are able to exceed the limit by 10-50%; higher limits seem to be ignored completely and the bandwidth tests report download speeds of over 10 times the speed I set. I'm using speedtest.net and some similar service from my ISP for these tests. Anyway, I don't necessarily need a program as complex as NetLimiter since I only need to throttle my machine's bandwidth, not a specific program's. In case you are wondering why in the world I'd want to cripple my Internet speed, there is a funny story behind this. Long story short, my modem gets random disconnects. Tech support comes in, says my Internet speed is abnormally high and I must be using some tools to somehow make it go faster than it's supposed to and this messes up my modem. I check the connection with another computer and it seems that my PC is the only one in my network that gets abnormal speeds. I reinstall my OS, speed looks normal at first, after I install the batch of 50 or so updates, it goes back to abnormally high speeds and the disconnect problems are not solved. Now I don't have a clue if the explanation the tech team gave me was just a strategy to lay the blame on someone else, but I was trying to give them the benefit of the doubt and see what happens if I really reduce my speed to their specification. Any help appreciated.

    Read the article

  • Is there any descent open-source search engine solutions?

    - by Nazariy
    Few weeks ago my friend asked me how hard is it to launch your own search engine service with list of websites that suppose to be crawled time to time. First what come at my mind was Google Custom Search however pricing policy is quite tricky and would drain your budget if you reach 500K queries per year. Another solution I found here was SearchBlox, which can be compared to Google Mini service. It's quite good solution if you planing to cover search over small amount of websites but for larger projects it is not very handy. I also found few other search platforms like Lucene, Hadoop and Xapian which seems to be quite powerful solutions to reach Google search quality, and Nutch as a web crawler. As most of open-source projects they share same problem, luck of comprehensive guidance of usage, examples and it's expected that you are expert in this subject. I'm wondering if any of you using this solutions, which of them would you recommend, and what should I be aware of?

    Read the article

  • DDWRT or similar as repeater in a network.

    - by Quantumplation
    I have a friend with sever connection issues due to her wireless router being on the bottom floor of her house, and the computer being a story or two away. I have several old Linksys routers lying about, one of which is currently running DDWRT for my network. Would it be a good idea (effective) to configure one of these routers as a wireless bridge of some kind in an intermediary floor to improve her connection? Is there any specific configuration beyond the standard DDWRT setup that I would need to do? Thanks for your help. =)

    Read the article

  • Remote desktop With client on Red Hat and Server Vista Business Edition

    - by Dean
    Hi, I'm trying to configure my vista machine to run the Remote Desktop Server yet i'm having problems. I have configured it using the following instructions. Yet it doesn't work. I have disabled the firewall and antivirus software but to no avail. I know the client is set up properly as i can log in to my friend's Remote Desktop server. The client i am using is rdesktop. What else can i try? Thanks in Advance, Dean

    Read the article

  • Printing from a Linux using an Acer Aspire Netbook

    - by JoelFan
    A friend asked me to check why their Linux Acer Aspire netbook can't print to their HP printer. When I plugged in the USB cable, the a "balloon" popped up on the netbook saying it was installing the printer. But the printing does not work. I was able to get into a Settings area and click on Print Test Page but nothing happened. If it was Ubuntu, I would go into the Log File Viewer, but I couldn't find that on whatever Linux flavor the Acer is running. I couldn't even figure out how to get to a terminal (shell) window. I tried searching the HP and Acer sites but nothing seems to apply to this issue.

    Read the article

  • Suspected Router problems, [closed]

    - by jordon_user
    I am new to this forum. I appreciate any help you can offer. I have been troubleshooting an error with both my WIRED Internet Connection I have 3 desktops running through this working connection (Router) with no problems. Two computers, one laptop and desktop experience the issue. If I connect directly to the Modem, on either, no problem on the internet. Through the Router, my computer connects for a period of time but if ever awaking my comp, or restarting, the yellow explanation mark returns. The only way I can get the connection up = cmd. ipconfig /release, ipconfig /renew. This constant command is annoying and was hoping for a permanent fix. Audio is also not working. I know its likely a driver error, but its an old comp we put together and if there's an easy fix itd be great to hear from you! If you need any more info just let me know. Thanks! THanks guys!

    Read the article

  • Why does just splitting an Ethernet cable not work?

    - by Sin Jeong-hun
    I thought the Ethernet is logically a one-line communication bus (for argument's sake, I am excluding hubs). All machines attached on the bus hears the same signals and the machines themselves try to avoid collisions by randomly backing off. http://computer.howstuffworks.com/ethernet6.htm If so, why would splitting one Ethernet line from my home router into two and connecting two computers not work? Why do I have to add a switch to it? *What the Internet said would not work. [4 port home router] ------[one Ethernet cable]-----[simple splitter]======[two computers] *What the Internet said I should do [4 port home router] ------[one Ethernet cable]-----[switch]======[two computers] Is this because of the signal degradation (reduced electric current)? Thank you for all the answers! The reason why I did not just use the two ports of my home router is... The 4-port gigabit router is in my room, and I had put a computer in another room (also my room, though). Since a wired network is far more reliable and secure, I had bought a long Ethernet cable and and connected the computer to the router. Now I was thinking about adding another computer to that room. I could buy another long Ethernet cable, but then there will be two cables between the rooms. The one line already is a minor annoyance, so I thought if I could share the one line between the two computers in that room. A switch would work, but it requires power and is a little bit pricey. That is why I wondered why it would not work to simply split the physical Ethernet cable. Apparently I do not completely understand how Ethernet and a switch work. I just have some bit of knowledge I heard in my college class.

    Read the article

< Previous Page | 513 514 515 516 517 518 519 520 521 522 523 524  | Next Page >