Search Results

Search found 11077 results on 444 pages for 'ip'.

Page 52/444 | < Previous Page | 48 49 50 51 52 53 54 55 56 57 58 59  | Next Page >

• Setting up Edimax EW-7206APg as Universal Repeater

  - by Ondra Žižka

  Hi, I've troubles setting up Edimax EW-7206APg as a Universal Repeater. I've read few manuals, but they are unclear on certain points. I've managed the repeater to get to a state when it's in a "connected" state. I've set the same WPA passphrase as the router has because I haven't seen any other place to set it at. These are my settings: System Uptime 0day:1h:33m:11s Hardware Version Rev. A Runtime Code Version 1.32 Wireless Configuration Mode Universal Repeater ESSID edimax Channel Number 6 Security WPA-shared key BSSID 00:c0:9f:40:bd:38 Associated Clients 0 Wireless Repeater Interface Configuration ESSID Dusan Security WPA BSSID 00:4f:62:23:8f:7e State Connected LAN Configuration IP Address 192.168.0.10 Subnet Mask 255.255.255.0 Default Gateway 192.168.0.1 MAC Address 00:c0:9f:40:bd:37 This is ipconfig /all: Prípona DNS podle pripojení . . . : riomail.cz Popis . . . . . . . . . . . . . . : Intel(R) PRO/Wireless 2200BG Network Connection Fyzická Adresa. . . . . . . . . . : 00-0E-35-3D-77-68 Protokol DHCP povolen . . . . . . : Ano Automatická konfigurace povolena : Ano Adresa IP . . . . . . . . . . . . : 192.168.0.5 Maska podsíte . . . . . . . . . . : 255.255.255.0 Výchozí brána . . . . . . . . . . : 192.168.0.1 Server DHCP . . . . . . . . . . . : 192.168.0.1 Servery DNS . . . . . . . . . . . : 94.74.192.252 94.74.192.244 I can ping the repeater, I can ping the root AP, but not a DNS server or any other IP beyond the root AP. Anyone has an idea what's wrong? Thanks, Ondra

  Read the article

• linux routing bug?

  - by Balázs Pozsár

  I have been struggling with this not easily reproducible issue since a while. I am using linux kernel v3.1.0, and sometimes routing to a few IP addresses does not work. What seems to happen is that instead of sending the packet to the gateway, the kernel treats the destination address as local, and tries to gets its MAC address via ARP. For example, now my current IP address is 172.16.1.104/24, the gateway is 172.16.1.254: # ifconfig eth0 eth0 Link encap:Ethernet HWaddr 00:1B:63:97:FC:DC inet addr:172.16.1.104 Bcast:172.16.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:230772 errors:0 dropped:0 overruns:0 frame:0 TX packets:171013 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:191879370 (182.9 Mb) TX bytes:47173253 (44.9 Mb) Interrupt:17 # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 172.16.1.254 0.0.0.0 UG 0 0 0 eth0 172.16.1.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 I can ping a few addresses, but not 172.16.0.59: # ping -c1 172.16.1.254 PING 172.16.1.254 (172.16.1.254) 56(84) bytes of data. 64 bytes from 172.16.1.254: icmp_seq=1 ttl=64 time=0.383 ms --- 172.16.1.254 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.383/0.383/0.383/0.000 ms root@pozsybook:~# ping -c1 172.16.0.1 PING 172.16.0.1 (172.16.0.1) 56(84) bytes of data. 64 bytes from 172.16.0.1: icmp_seq=1 ttl=63 time=5.54 ms --- 172.16.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 5.545/5.545/5.545/0.000 ms root@pozsybook:~# ping -c1 172.16.0.2 PING 172.16.0.2 (172.16.0.2) 56(84) bytes of data. 64 bytes from 172.16.0.2: icmp_seq=1 ttl=62 time=7.92 ms --- 172.16.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 7.925/7.925/7.925/0.000 ms root@pozsybook:~# ping -c1 172.16.0.59 PING 172.16.0.59 (172.16.0.59) 56(84) bytes of data. From 172.16.1.104 icmp_seq=1 Destination Host Unreachable --- 172.16.0.59 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms When trying to ping 172.16.0.59, I can see in tcpdump that an ARP req was sent: # tcpdump -n -i eth0|grep ARP tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 96 bytes 15:25:16.671217 ARP, Request who-has 172.16.0.59 tell 172.16.1.104, length 28 and /proc/net/arp has an incomplete entry for 172.16.0.59: # grep 172.16.0.59 /proc/net/arp 172.16.0.59 0x1 0x0 00:00:00:00:00:00 * eth0 Please note, that 172.16.0.59 is accessible from this LAN from other computers. Does anyone have any idea of what's going on? Thanks. update: replies to the comments below: there are no interfaces besides eth0 and lo the ARP req cannot be seen on the other end, but that's how it should work. the main problem is that an ARP req should not even be sent at the first place the problem persist even if I add an explicit route with the command "route add -host 172.16.0.59 gw 172.16.1.254 dev eth0"

  Read the article

• Ubuntu 12 crashed and took down network

  - by Leopd

  We recently set up a new Ubuntu 12.04LTS server on our network. It's not fully configured so it's not doing much beyond sshd and a default apache2 install. But this evening it appears to have crashed. It wasn't responding to the network or the keyboard. But the worst part is, it took down the entire network. My knowledge of the network stack below OSI layer 3 is very limited, so the rest confuses me. When this machine was physically connected to the network, no other machine could connect to the outside internet. When things were broken, running arp showed that our gateway's IP address (10.0.1.1) was listed as "invalid." Unplugging the server from the network fixed the problem, and plugging it back in broke it again. So the crashed server was advertising itself as owning the gateway's IP address? There's nothing at all in syslog during the time when it was causing problems. Any ideas about how to figure out what went wrong or what we can do to prevent it from happening again? I'm hesitant to even put the machine back on the network right now. Update ** It crashed again, and I ran tcpdump -penn arp (thanks bahamat!) for several minutes and got this... (timestamps and duplicate lines removed) 00:1e:65:f8:dc:24 > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 60: Request who-has 10.0.1.1 tell 10.0.2.191, length 46 00:1e:65:f8:dc:24 > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 60: Request who-has 10.0.1.44 tell 10.0.2.191, length 46 60:d8:19:d4:71:d6 > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 60: Request who-has 10.0.1.1 tell 10.0.2.125, length 46 d4:9a:20:04:e9:78 > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 42: Request who-has 192.168.1.1 tell 192.168.1.100, length 28 Update 2 ** When the network is functioning properly, arping -c4 10.0.1.1 returns this: ARPING 10.0.1.1 60 bytes from c0:c1:c0:77:25:8e (10.0.1.1): index=0 time=267.982 usec 60 bytes from c0:c1:c0:77:25:8e (10.0.1.1): index=1 time=422.955 usec 60 bytes from c0:c1:c0:77:25:8e (10.0.1.1): index=2 time=299.215 usec 60 bytes from c0:c1:c0:77:25:8e (10.0.1.1): index=3 time=366.926 usec --- 10.0.1.1 statistics --- 4 packets transmitted, 4 packets received, 0% unanswered (0 extra) When the bad server is plugged in, arping -c4 10.0.1.1 returns: ARPING 10.0.1.1 --- 10.0.1.1 statistics --- 4 packets transmitted, 0 packets received, 100% unanswered (0 extra) Context ** 10.0.x.x is the main subnet. 10.0.1.1 is the main internet gateway 10.0.1.44 is a printer 10.0.2.* devices are all laptops / workstations I have no idea what's using the 192.168.x.x subnet -- your guesses are at least as good as mine. A VM on a workstation? A misconfigured WAP? Somebody re-sharing wifi? A machine that failed to DHCP? The offending ubuntu server's MAC address ends in cd:80 so isn't listed in the dump. It should DHCP to 10.0.3.3 Thanks for any help. This ARP stuff is all voodoo to me. Packets just go to IP addresses, right? ;)

  Read the article

• dedicated server - cgi-sys/defaultwebpage.cgi redirect when accessing via server IP

  - by Ross

  This isn't so much of a problem, but would like to know why this happens. we have a dedicated server running WHM. If I access the server via its IP address directly I am automatically redirected to http://xx.xxx.xx.xxx/cgi-sys/defaultwebpage.cgi I know how to edit this page (this isnt the problem) I'm just curious why I get redirected to this .cgi page, rather than simply remain @ xx.xxx.xx.xxx/ and view my default "landing page", if you like. What setting could I change so that if anyone visits my server IP, they do not get redirected to xx.xxx.xx.xxx/cgi-sys/defaultwebpage.cgi For instance if you visit 173.194.37.104 (google), you view the google home page, but URL remains the same. Hope this makes sense. thanks

  Read the article

• Dual Exchange 2010 on different VM + single public IP + multiple domains

  - by Shivan Raptor

  Here is the scenario: I have 2 Exchange Server 2010 on 2 different Virtual Machines, created by and based on Hyper-V. They have IP and domain: 192.168.5.11, domainA.com ; and 192.168.5.12, domainB.com respectively. The problem is, I only have 1 public IP, say 123.123.1.1 . How do I configure the settings so that I can successfully receive emails using both Exchange servers? Given that I cannot use single Exchange server for multiple domains. -- UPDATE -- To clarify, the domainA.com and domainB.com mentioned above are website domains, instead of multiple Active Directory forests. Users of the two Exchange Server shares the same Active Directory. I know that ONE Exchange Server can handle multiple domains, but I would like to separate them into different Virtual Machines, for load balancing and data separation.

  Read the article

• Tunneling a TCP/IP Connection through Remote Desktop Connection

  - by Kristopher Johnson

  There is a remote Windows server on a private network which I can connect to via Remote Desktop Connection. I would like to be able to make TCP/IP connections from my computer to other computers on that server's network. Remote Desktop Connection makes it possible to share printers, drives, and other local resources through the connection. Is there any way to "tunnel" a TCP/IP connection via RDC? I'd like something similar to the port-forwarding provided by SSH. I don't see any way to do this via RDC, but I'm hoping the capability is there and I just don't know about it.

  Read the article

• Monitoring Bandwidth Usage (Per Internal IP) - Cisco ASA 5505

  - by Joseph Sturtevant

  I manage a small network with a Cisco ASA 5505 and a shared DSL connection. I would like to be able monitor the bandwidth usage of the various users/devices on my network (by IP). Can I do that using the ASA? Has anyone got this working? What is the best way to do this? Some Ideas I Have Seen Online: SNMP with a tool like Cacti Does this give per IP usage with an ASA or just overall usage? Netflow with a tool like ntop Couldn't get this to work. It seems that the Netflows sent by ASA are not exactly standard. Ntop receives them, but doesn't seem to know what do with them.

  Read the article

• dedicated server - cgi-sys/defaultwebpage.cgi redirect when accessing via server IP

  - by Ross

  Hi This isn't so much of a problem, but would like to know why this happens. we have a dedicated server running WHM. If I access the server via its IP address directly I am automatically redirected to http://xx.xxx.xx.xxx/cgi-sys/defaultwebpage.cgi I know how to edit this page (this isnt the problem) I'm just curious why I get redirected to this .cgi page, rather than simply remain @ xx.xxx.xx.xxx/ and view my default "landing page", if you like. What setting could I change so that if anyone visits my server IP, they do not get redirected to xx.xxx.xx.xxx/cgi-sys/defaultwebpage.cgi For instance if you visit 173.194.37.104 (google), you view the google home page, but URL remains the same. Hope this makes sense. thanks

  Read the article

• One IP, One Port, Multiple Servers

  - by Adrian Godong

  I am looking for a solution to forward one public IP address and one specific port to different machines based on hostname (as of now, I need it only for HTTP). The current setup is NAT on a commodity router (it only provide simple public port to private IP address / port forwarding). I can add a Windows Server 2008 R2 machine before the router if required, but prefer not to do so. So ideally, I would like to have the current setup and the forwarding is done on one of the Windows Servers. Is it possible to do this?

  Read the article

• How to Unban an IP properly with Fail2Ban

  - by psp

  I'm using Fail2Ban on a server and I'm wondering how to unban an IP properly. I know I can work with IPTables directly: iptables -D fail2ban-ssh <number> But is there not a way to do it with the fail2ban-client? In the manuals it states something like: fail2ban-client get ssh actionunban <IP>. But that doesn't work. Also, I don't want to /etc/init.d/fail2ban restart as that would lose all the bans in the list.

  Read the article

• two domains two servers one dynamic ip address

  - by giantman

  as i said i have 2 domain hi.org and bye.net and one dynamic ip address and two servers. i want to attach one domain bye.net to server1 and hi.org to server2. using apache wamp 2.0i. i hope someone will be able to answer. ` httpd.conf file additions ProxyRequests Off Order deny,allow Allow from all vhost file additions NameVirtualHost *:80 default DocumentRoot "c:/wamp/www/fallback" Server 1 DocumentRoot "c:/wamp/www" ServerName h**p://bye.net ServerAlias bye.net Server 2 ProxyPreserveHost On ProxyPass / h*p://192.168.1.119/ DocumentRoot "g:/wamp/www" ServerName h*p://hi.org ServerAlias hi.org ` after doing all this i fallback to server1 only i don't get the page hi.org i only get the page bye.net, i don't even get the default fallback page which gets executed when a person enters ip address but not the domain name. i use windows 7 (server2) and windows xp (server 1)

  Read the article

• Restrict IPMI access on Dell BMC and iDRAC to an allowed IP range

  - by edgester

  I'm trying to secure the iDRAC's and BMC's on some of my Dell servers (R210, R410, R510). I want to restrict access to IPMI commands to only a few IP addresses. I've successfully restricted access to the iDrac using the instructions from http://support.dell.com/support/edocs/software/smdrac3/idrac/idrac10mono/en/ug/html/racugc2d.htm#wp1181529 , but the IP restrictions do not affect IPMI. A separate management network is not practical at this time because of lack or ports and some Dell BMC's don't offer a separate port. I'm told by my networking group that our switches don't support trunking, so using the vlan tagging is not an option either. Is there a way restrict the IPMI access to a list of allowed addresses? FYI, for various reasons, I have a mix of Dell servers with BMC's, iDrac Express and iDrac enterprise management features.

  Read the article

• Unable to ping local machines by name in Windows 7

  - by aardvarkk

  I'm having a strange (and persistent!) problem with pinging local machines on my network by name. I believe my machine (Windows 7 64-bit) is the only one having this issue. This is over a wireless connection. As an example, consider a device on my network by the name of WDTVLiveHub. It's a Western Digital Live Hub (surprise!). If I go to my router's DHCP Client Table in the browser (my router is a WRT400N), I see this entry: WDTVLiveHub 192.168.1.101 Great. So I try to ping that IP address: ping 192.168.1.101 Pinging 192.168.1.101 with 32 bytes of data: Reply from 192.168.1.101: bytes=32 time=9ms TTL=64 Reply from 192.168.1.101: bytes=32 time=16ms TTL=64 Reply from 192.168.1.101: bytes=32 time=16ms TTL=64 Reply from 192.168.1.101: bytes=32 time=16ms TTL=64 Ping statistics for 192.168.1.101: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 9ms, Maximum = 16ms, Average = 14ms OK, still looking good. Now I try to ping it by name: ping WDTVLiveHub Ping request could not find host WDTVLiveHub. Please check the name and try again. From what I've read, this implies a problem with DNS servers and host name lookups. Interestingly, if I type the following: pathping 192.168.1.101 I get this output: Tracing route to WDTVLIVEHUB [192.168.1.101] over a maximum of 30 hops: 0 Scotty [192.168.1.103] 1 WDTVLIVEHUB [192.168.1.101] Computing statistics for 25 seconds... Source to Here This Node/Link Hop RTT Lost/Sent = Pct Lost/Sent = Pct Address 0 Scotty [192.168.1.103] 1/ 100 = 1% | 1 12ms 1/ 100 = 1% 0/ 100 = 0% WDTVLIVEHUB [192.168.1.101] Trace complete. Scotty is obviously the name of my local machine. So it's able to find the name somehow when I do that approach... ipconfig /all shows the following under DNS servers: DNS Servers . . . . . . . . . . . : 192.168.1.1 ***.***.***.*** ***.***.***.*** Where the * represents the same DNS servers that show up in my router under DNS 1 and DNS 2 through the Internet. For completeness, here's the whole output of ipconfig /all: Windows IP Configuration Host Name . . . . . . . . . . . . : Scotty Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Peer-Peer IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Dell Wireless 1397 WLAN Mini-Card Physical Address. . . . . . . . . : 0C-EE-E6-D1-07-E8 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv6 Address. . . . . . . . . . . : 2002:d83a:31e5:1234:5592:398e:8968:43d1(Preferred) Temporary IPv6 Address. . . . . . : 2002:d83a:31e5:1234:ecce:2f79:72a5:5273(Preferred) Link-local IPv6 Address . . . . . : fe80::5592:398e:8968:43d1%26(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.1.103(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : September-17-12 11:05:57 PM Lease Expires . . . . . . . . . . : September-18-12 11:05:57 PM Default Gateway . . . . . . . . . : fe80::200:ff:fe00:0%26 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DHCPv6 IAID . . . . . . . . . . . : 537718502 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-12-80-3D-D7-00-26-B9-0D-08-70 DNS Servers . . . . . . . . . . . : 192.168.1.1 ***.***.***.*** ***.***.***.*** NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter VirtualBox Host-Only Network: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VirtualBox Host-Only Ethernet Adapter Physical Address. . . . . . . . . : 08-00-27-00-98-9A DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::b48a:916b:c0f:fb29%23(Preferred) Autoconfiguration IPv4 Address. . : 169.254.251.41(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : DHCPv6 IAID . . . . . . . . . . . : 570949671 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-12-80-3D-D7-00-26-B9-0D-08-70 DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1 fec0:0:0:ffff::2%1 fec0:0:0:ffff::3%1 NetBIOS over Tcpip. . . . . . . . : Enabled Tunnel adapter Local Area Connection* 15: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter isatap.{55899375-C31D-4173-A529-4427D63FD28B}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft ISATAP Adapter #2 Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter isatap.{64B8F35F-A6AB-4D6B-B1D5-DD95F57B1458}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft ISATAP Adapter #3 Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Not sure exactly how to diagnose exactly what's going on... but the problem is really frustrating! The biggest problem is that my mapped network drives have to be done by IP, and then any time the router assigns new IP addresses to those devices, all of my network shares break again. Stinks! Would love some assistance on possible solutions. I've tried all of this netsh catalog resetting and that didn't seem to fix anything at all. Would love an explanation of what's going wrong, too, rather than blindly resetting things! Thanks!

  Read the article

• One domain, dedicated SSL IP on whm

  - by Vanja D.

  It's long, but please read carefully. I am trying to install an SSL certificate on my dedicated server with WHM/cPanel. I have a dedicated IP to use with the SSL certificate. My main domain is example.com (NOT www.example.com), and I have an account and website already running on it. I bought the certificate for the main domain (example.com without www.). I installed the certificate (successfully). I used the example.com domain, the dedicated IP and the same cPanel user which owns example.com (non-ssl) I double checked ConfigServer for port 443 being open. RESULT: https://example.com won't open, ssl check tool returns a "SSL is not configured on this port (443)" error. I have three questions: where did I go wrong, wht did I miss? is it possible to have one domain on two ips (one for http, one for https)? is it possible to have an ssl host with the same user as the regular one?

  Read the article

• Socksify TCP connections reaching a gateway IP -- preferably without iptables

  - by Alexandra Neagu

  I have Virtualbox installed on Debian with a few virtual machines. I can't install anything in the guests, and I use host only networking, vboxnet0. The host IP in the host network is 192.168.56.1, and the guests have static IPs in 192.168.56.0/24. I access Internet with a SOCKS proxy (without authentication) and I would like the Virtualbox guests TCP connections to be sent through the SOCKS proxy. This would also be useful for socksifying external TCP reaching a gateway network card or wireless access point. I looked at transocks, tun2socks, with dante-client, etc., but I don't know how can I achieve this without enabling IP forwarding in the host and using iptables. Maybe to attach somehow the Virtualbox vboxnet0 network to the tunnel tun0 used by tun2socks? Or maybe there is a way to do NAT to tun0 in Virtualbox? I only need TCP traffic and I don't need UDP, not even for DNS.

  Read the article

• MAC Address to IP

  - by IT_07

  Is there a way to get the IP address when all you have is the MAC of an item?

  Read the article

• Access to NTP via IP which doesn't change often

  - by faulty

  I'm trying to sync the clock of our production server located in a data center with pool.ntp.org. For security reason, our servers has no internet access unless we requested to open specific ip/port explicitly. I worked out a list of IPs based on 0.asia.ntp.org 1.asia.ntp.org 2.asia.ntp.org 3.asia.ntp.org Not realizing ntp.org is using round robin DNS and the servers being voluntary, they changes from time to time. In fact the IP I've got from 3.asia.ntp.org last month is no longer working now. I'm wondering if there's a publicly known NTP server that doesn't change as often or if there's a way to go around this without having to request an update to the firewall on a monthly basis. I believe many admin is facing the same issue here.

  Read the article

• How to configure LAN IP Filter on Huawei E586 UMTS Modem

  - by Mose

  I need to prevent clients of an Huawei E586 UMTS to WiFi modem from downloading much data from specific servers eg. Windows update or OSX update. On the config page of the device there's an "LAN IP Filter" which seems pretty good but I can't figure out the right settings. The mask looks like this: The help pages states the following: My problem with this is, I want some wildcard for the local ip and port. In my opinion the help page can not be correct by "lan port: enter 80" because the source port is normally dynamic. I tried to set it up like stated there but as expected it doesn't work. As wildcards I tried * and "ALL" but nothing worked as it prevents me from saving settings with an "wrong value" error. Any suggestions? Thanks in advance!

  Read the article

• How to pass an IP address to inet_addr?

  - by November

  I can't seem to pass an IP address to inet_addr. I have gone through the debug but I still can't figure out why this won't work. printf("Server IP\nIP:"); scanf("%s",cmdPtr); //Bind socket address.sin_family = AF_INET; address.sin_addr.s_addr = inet_addr(&cmdPtr); address.sin_port = htonl(SERVER_PORT); lenC = sizeof(address); if (connect(sdC, (struct sockaddr *) &address , lenC) < 0) { perror("Could not bind Socket\n"); return -1; }

  Read the article

• Remote connection IP to use

  - by petwho

  I have two laptops that both run on ubuntu and installed ssh server and ssh client on them. One is usually on my desk at home and one I usually bring to my company. When I'm at home I can easily ssh to one from the other by typing this command (to login to the other laptop whose IP address is: 192.168.0.105) : ssh -p 22 [email protected] However, When I'm at my company, I try to type the same command and ofcourse it doesn't work. I understand that when at home I'm on LAN network, that my laptops actually using my ISP's address which differ from 192.168.0.107 asummed 203.113.131.1. So could you tell me what IP that ssh shoud use for my laptop (at work) to connet to my computer at home? Thank you.

  Read the article

• Track IP Messenger's chatting by wireshark

  - by Kumar P

  We have Linux server ( RHEL 5 ), and some client machines ( Windows XP ) in local area network. We using server as proxy server. I am using squid proxy. My windows machines using internet by proxy. Now my client machines using IP messenger for chatting and sharing files with in local network. How can i trace what they are doing or chatting by ip messenger, from my server by wireshark packet sniffer ? If i can't do it by wireshark , What will you give idea about it...

  Read the article

• Can't ping devices by IP address for devices allocated IPs by DHCP

  - by GiddyUpHorsey

  I have a home network with a Trendnet wireless router and a Windows Domain. The Domain Controller/DNS server is a Windows 2000 Server and is configured to forward queries to DNS servers provided by the ISP. The router provides DHCP and is configured with the Windows 2000 Server as the DNS server. The network has been set up for a couple of years and usually works fine. When I connect iPhones to the network over WiFi, the router can ping the iPhones through its browser based admin interface, but Windows machines that are part of the Windows Domain cannot. A laptop was connected to the network over WiFi that wasn't joined to the domain and it could see the iPhones. The router UI shows that the laptop has a reserved IP allocated via DHCP. All machines either have a static or DHCP allocated IP on the 192.168.0.* subnet. Router - 192.168.0.1 - Static - Wired Windows Domain Controller - 192.168.0.8 - Static - Virtual Windows 7 Workstation - 192.168.0.200 - DHCP Auto - Wired VMWare ESXi Host - 192.168.0.201 - Static? - Wired iPhone 1 - 192.168.0.202 - DHCP Auto - WiFi iPhone 2 - 192.168.0.203 - DHCP Auto - WiFi Windows Vista Laptop - 192.168.0.204 - DHCP Reserved - WiFi Using the Windows 7 machine (200), I try to ping each machine and the only DHCP machine that responds is itself. The other DHCP machines fail with Reply from 192.168.0.200: Destination host unreachable.. Using nslookup fails with *** domain.controller.name can't find 192.168.0.203: Non-existent domain. Using the Windows 2000 Domain Controller (8), I try to ping each machine and the only DHCP machine that responds is the Windows 7 machine (200). Pinging the other DHCP machines fails with Request timed out.. Using nslookup also fails with *** domain.controller.name can't find 192.168.0.203: Non-existent domain. Using the iPhone 2 (203), I try to ping (Network Ping Lite) the machines with static IP addresses and that works fine. When I try to ping the Windows 7 machine (200) it is unable to get a response. How do I configure the DNS server/Windows Domain/Router properly so that the Windows Domain machines can see the IPs allocated via DHCP?

  Read the article

• Assign two static IP addresses to one mac address

  - by Timo Ylikännö

  Can Isc-dhcp-server give two static ip addresses to one mac address? I have several home terminals in my network. Each terminal have two interfaces. One for public traffic and one for a management traffic. Both interfaces have same mac address. DHCP server can detect interfaces via dhcp option field and dhcp class declarations. Every terminal have to have static ip address instead of dynamic address. With dynamic address and dynamic pools this would be an easy task. Or is there any dhcp server that can do this?

  Read the article

• Apache server in raspberry PI not visible from outside( public IP)

  - by Kronos

  I have made a fresh install of Arch Linux ARM into a Raspberry PI and I mounted there a LAMP, all fresh. I have another Arch(x86) in my laptop with Apache also there, and as far as I know, two web servers cannot run in the same network segment so, the problem is as follows. I my laptop, having Apache running, if I enter via the public ip of my network everything turns ok and I can see my website but, (obviously turning this server down) if I enter from the public IP with the Apache running in the raspberry pi( yes, only that Apache running) i cannot see my website in there. Also, if I access via local network it is a normal success, I can see my website. So, I can enter my raspberry website only via local but in my other web server i can enter it via local and public. I have the same conf files in both of them so what is the difference? I was planning in making the rpi as a development server. Thanks in advance

  Read the article

• Does IP helper forward subnet broadcasts?

  - by Eamon

  Hi, I have a device on a VLAN that uses UDP subnet broadcasts to advertise its presence to similar devices. This works fine on a single VLAN, but now I need to allow it to communicate with similar devices on a second VLAN. I thought of using the IP helper command in the router, but I am wondering if that only forwards global broadcasts (255.255.255.255)? My device sends out a subnet broadcast (e.g. 192.168.6.255) Will IP helper change the destination address to the target subnet (e.g. 192.168.7.255)? Eamon

  Read the article

< Previous Page | 48 49 50 51 52 53 54 55 56 57 58 59  | Next Page >